1. Electronics and Instrumentation Lab. S. NO. NAME OF ARTICLE WITH SPECIFICATION Budgam Ganderbal Kulgam Quantity required for Anantnag Kishtwar Udhampur Doda Samba Unit cost to be quoted 1. Fully Automatic Compression Testing Machine 2000 KN capacity, fully Automatic Electrically Operated for testing specimens of concrete cubes & cylinders, cold crushing strength of refractory and other materials. The machine should consist of loading unit,- pumping unit, calibrated gauges, Computer System with software and should confirm to IS 14858. 2. Vee Bee Consistometer As per IS 119 consisting or vibrating table 380mm long and 260mm wide. Resting upon elastic support at a height of about 305mm above the floor Complete with start/stop switch, cord and plug. A holder is fixed to the base into which a swivel arm is telescoped with funnel and guide sleeve. The swivel arm is also detachable from the vibrating table. A graduated rod is fixed on a swivel arm and at its end a plastic
disc is screwed. The divisions of scale on the rod record the slump of the rod record the slump of the concrete in millimeters. Supplied complete with a sheet metal container with lifting handles which can easily be fixed to the vibrating table. A slump cone open at both ends with lifting handles and a tamping rod of size 16mm dia and 600mm long rounded at one end. 3. Blaine s Air Permeability Apparatus Consisting of permeability cell, U tube manometer mounted on a Stand with a stop cock, perforated disk, p1unger rubber stopper, rubber tube 30 cm long, packet of filter paper discs, and a bottle of 100 cc dibutyiphthalate liquid confirming to IS 403, 5516, 1727 and 4028. 4. Curing Tank Temperature Range 5 0 C to 100 0 C. The tank should accommodate 150 mm/70.6 mm cubes upto 36 / 72 cubes and fully insulated covered with a hinged lid, heater, and thermostat and recirculation pump. Provision of two removable racks with free circulation of water around each cube, pump, drain valve etc. complete 5. Los Angeles Abrasion Testing machine Consisting of hollow cylinder mounted
on a sturdy frame on ball bearings. A detachable shelf which extends throughout the inside length of the drum, catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated at a speed of 30-33 rpm by an electric motor through a heavy duty reduction gear with a tray provided for sample collection etc complete 6. Cement Motar Cubes 70.6 mm cube confirming to IS 10080 7. Flexure Strength Testing Machine. Consisting of light weight rugged high strength frame, double action hydraulic pump, self aligning roller assembly and hydraulic jack provided with retraction spring. 8. Density Basket 06 06 06 06 06 06 06 06 Ruggedly constructed from galvanized wire mesh,20cm dia x 20cm high (approx) 9. Cylindrical Metal Measure Consisting of one each of the following measures: 3litres, 5litres and 30litres. A tamping rod of 16mm dia x 60cm long should also be provided.
10. I.S. Sieves 20 cm diameter brass 03 Sets 03 Sets 03 Sets 03 Sets 03 Sets 03 Sets 03 Sets 03 Sets Aperture size 4.75 mm,2.36 mm,1.18 mm,600micron,300 micron,150 micron and 75 micron as per IS 460 11. California Bearing Ration Test Apparatus Electrically operated of motorized load frame, capacity 5000kg, Mould, perforated base plate, Penetration piston, extension collar, metal space disc, annular metal weight, slotted metal weight, proving ring, dial gauges, tripod stand, cutting collar, rammer 2.6 kg weight with drop of 310mm,rammer 4.89 kg weight with drop of 450mm etc complete as per IS 2720(XVI) 12. Core Cutter Consisting of cylindrical core cutter 100 mm dia and 130 mm long, steel dolly 25 mm high, rammer with steel rod etc complete as per IS 2720(XXIX) 13. Universal Automatic Rammer Electrically operated motor driven mechanical compactor used for compaction of soil in 100 mm and 150
mm dia moulds. Rammer - Circular faced, 50 mm dia adjustable to 2.6 kg or 4.9 kg weight, drop adjustable to 310 mm -450 mm 14. Proctor Penetrometer Consisting of a body housing a spring a plunger calibrated to read 0-40 kg X 1 Kg and a handle Two stems are provided, a Larger stem and a shorter stem both graduated at 12.5 mm intervals, to indicate the depth of penetration. Needle point set comprising of each of 0.25,0.5,1,1.5,2,3.5 cross sectional area and 6 cm and a Tommy Pin Complete. 15. Laboratory Vane Shear Apparatus Consisting of a torque head, adjustable in height by means of a lead screw rotated by a drive wheel to enable the vane to be lowered into the specimen. Rotation of the vane is by means of an electric motor which operates a worm gear arrangement turning the upper end of a calibrated torsion spring. The vane shaft is attached through the hollow upper shaft to a resettable
pointer which indicates the angle of torque on a dial graduated in degrees. The rate of rotation should be 1/60 rpm. The equipment should consists of one container and set of 4 springs, (one each of capacity 2kg-cm, 4kgcm,6kg-cm and 8kg-cm) 16. Field Vane Shear Apparatus The equipment should consists of Torque Applicator Assembly complete with stand having a capacity 2000kgcm, vane(with vane rod) 37.5mm dia x 75mm high, vane (with vane rod) 50mm dia x 100mm high, torque rod (square cross section) 60cm long, rods (quick coupling type) 1m long, rods (quick coupling type) 0.5m long and a dummy rod 17. Digital Platform Balance Capacity 50 Kg 18. Hand Operated Extractor The equipment should consists of sample extractor frame of screw type with a wire sample trimmer, jarring link for driving the sample tube of 38mm dia, adapter with locking screw for fitting the 38mm dia sampling tube to
jarring link, split mould 38mm x 88mm long provided with quick releasing clamps, split mould 38mm x 76mm long and 1 pair sampling tube unrelieved 38mm dia x 200mm long. 19. Sample Ejector The equipment should consists of adapter rings and ejector discs fior 38,50,75,100 and 150mm dia sampling tubes and moulds and sampling tube unrelieved 38mm dia x 200mm long. 20. Infra Red Moisture Meter The equipment should consists of heating element, thermometer (L shaped) and bulb. The capacity and sensitively should be 10g approx and 5mg approx respectively. The range of the stuff gauge should lie in 0-1g. the reading accuracy should be +/- 0.20%. The range of thermoregulation should be 75-160C. The diameter of scale pan should be 100mm. 21. Stripping value Apparatus Consisting of a circular tray rotating in a vertical plane at a rate of
approximately 100rpm by an electric geared motor, four bottles mounted on circular tray, time switch etc complete 22. Flash Point and fire Point Apparatus Consisting of Flash cup brass with a insulated handle power supply, thermometer etc complete as per IS 1448(Part69) 23. Standard Tar Viscometer Consisting of a chrome plated copper bath, with a drain valve and a central tube to receive the test cup and to position the stirrer, and is mounted on a stand with leveling feet. Stirrer has a curved shield and is provided with an insulated handle, thermometer socket and a swivel support for the valve. Supplied complete with 10 mm cup and ball valve 24. Say Bolt Viscometer It should comprises one each of cylindrical oil cup, universal tip, furol tip, bath fitted with immersion heater mounted on a stand, dimmer stat for temperature control, stirrer with
shield. Apparatus is supplied complete with insulated handle and thermometer support, receiving flask, withdrawal tube, filter funnel, thermometer support for cup and circular spirit level. 25. Marshall Apparatus The Equipment should consists of Marshall load Frame Cap 50 KN having speed 50.8 mm/min, Breaking head stability mould, steel cylindrical compaction mould, base plate, extension collar, manually operating compaction pedestal comprising of a steel plate capped on a wooden post, mould clamp should be fitted to the top of the plate, compaction hammer for use with compaction pedestal and mould having weight 4.5 kg with a free fall of 457 mm, load transfer bar, sample ejector for 4 inches dia sample, dial gauge 25 mm travel having 0.01 mm least count and proving ring with capacity 25 KN(2500 kgf) 26. Hot Plate Rectangular with energy regulator
300x450x180mm, 2.0 Kw. 27. Mastic Asphalt Taster The equipment should consists of water bath 440x350x180mm, mould 150mm dia x 25mm depth. The heating power should be 1KW and the temperature range should be room temperature to 85+/-0.1 C. the accuracy of penetration should be 0.01mm. 28. Pavement Intensity Test apparatus The equipment should consists sturdy frame having two chrome plated pillars and cross head having capacity 100 KN. The maximum vertical distance between the plates should be 200mm. The allowed overload should be 30%. The speed of piston should be 50.8mm/min (high) and 1mm/min (low). The speed can be adjusted with the help of mechanical lever fitted on main frame. 29. Vertical Asphalt Mixing Apparatus The equipment should consist of main frame, variable speed mixer, elevating
system, heating pot, electrical control box, gear box and vertical curved blade. The elevating system consists of a motor, worm gear, up right column, guide bar and stopper block and the heating pot has a double lever metal pot, conduction coil and electrical heater. The vertical capacity should be 20lt. The temperature range should be room temperature to 200+/-0.5 C. The timer should be in the range of 0-999sec. The speed of blade should be 42-48 rpm (revolution) and 70-75 rpm (rotation). The vertical heating power should be 3KW. The testing environment should be 10 to 40C & < 80% RH. The power should be 415v,50hz, 10A, 3ph. 30. Automatic Level 06 06 06 06 06 06 06 06 Magnification 32x, standard deviation per km (double run level)=2.0mm Accessories : Stand: Aluminum (heavy duty)-1no Staff : Aluminum (4m folding)-1no 31. Digital Theodolite 03 03 03 03 03 03 03 03
2 angle accuracy,30 x telescope, clear aperture 45mm two faced LCD display. Till compensation automatically, range o compensator +3 nickel hydrogen chargeable battery. Accessories: all standard accessories included complete with manual and training of staff. 32. Ranging Rod 30 30 30 30 30 30 30 30 Made of mild steel, 3m high, alternate red and white paint strips, flag at top, and metal shoe. 33. Reynolds s Apparatus The apparatus should consists of a glass tube with one end having bell mouth entrance, connected to a constant head water tank, at the other end another valve is provided to vary the flow rate. A self contained water re - circulating unit, provided with a sump tank and a centrifugal pump should also included in setup. Flow control valve and by pass valve should be fitted in water line. A capillary tube should be introduced centrally in the bell mouth for feeding dye from a small container placed at the top of tank,
through polythene tubing. 34. Pitot Tube Ellipsoidal head, an intake for total pressure and 6 holes for static pressure, sheated thermometer K probe integrated, with connection cable length 1.5m. Body made of stainless steel 35. Universal Current Meter The equipment should consists of a streamlined body which houses the sensing mechanism, an encapsulated reed switch, and the horizontal axis propeller shaft which has a permanent magnet mounted on it. The current mater should be provided with a calibration certificate and rating table. 36. Searls Apparatus The apparatus should comprise of two metal frames connected by a link mechanism carrying a sprit level. Supplied complete with ceiling bracket having itself a pair of chucks similar to those on the frame, counter poise weight and set of suitable wires, without slotted masses. The wire under test is
held in self centering steel chucks capable of holding wires of 1.mm diameter (18SWG).A micrometer head reading to 0.01mm is provided for readjusting the spirit level. 37. Simple Roof Truss Apparatus Bench-top, to demonstrate simple structure in civil engineering. Pinjointed structure frame loaded at its apex by dead weight. Leaf-spring balances. Adjustable tie. Digital caliper. Weight hanger, weights set. 38. Beam deflection Apparatus The main frame of the apparatus should consists of an upper cross member carrying graduated scales and two lower members bolted to T - legs to form a rigid assembly. The three load cells and cantilever - support pillar slide along the lower members and can be clamped firmly in any position. The load cells should have direct digital read out and each should be fitted with a hardened steel knife edge which can be adjusted to set the intial level or to simulate a sinking support. Locking pins should convert
each load cell to a rigid support when required. The cantilever support should be a rigid pillar with a sturdy clamping arrangement to hold the beams when built-in end conditions are required. Four weight hangers and a set of weights should be supplied to apply static loads. Three digital indicators should measure all beam deflections. The indicators should mount on magnetic carriers that slide along the upper cross member. The indicators, carriers, load cells and weight hangers should all have cursors that register on the scale (located on the upper cross member) to ensure easy, accurate positioning. All digital indicators and load cells should have sockets for connection.