TORi Minimalist Linear CSS - Cable Suspended J-BOX (BY OTHERS) 3-O or 4-0 MUD RING (BY OTHERS) J-BOX BRACKET BAR 1/4-20 STUD 8-32 BRACKET BAR SCREWS (BY OTHERS) CANOPY STND - 5 CANOPY 1. Cut cables to desired length - take care not to fray cable ends. 2. Insert cables into gripper ends and adjust to desired length. 3. Insert power cable through canopy and secure with provided strain relief. 4. Complete wire make-up. 5. Install canopy with cable gripper parts. CANOPY MOUNTING GRIPPER AIRCRAFT CABLE NC - NO CANOPY TYPICAL TORI CABLE SUSPENDED COMPONENTS CABLE LENGTH
TORi Minimalist Linear CSS - Cable Suspended Cable Mount Center Dimensions Nominal Wattage Cable Mounting Centers 3' 21w 39w 35-5/8" 4' 28w 54w 47-7/16" 5' 35w 80w 59-1/4" Overall T5 T5HO 2' 14w 24w 23-13/16" 24-13/16" 36-5/8" 48-7/16" 60-1/4" TORi-RB S Nominal Wattage Cable Mounting Centers T5 T5HO 2' 14w 24w 24-1/16" 3' 21w 39w 35-5/8" 4' 28w 54w 48-11/16" 5' 35w 80w 60-1/2" Overall 24-5/16" 35-7/8" 48-15/16" 60-3/4" TORi-IB Continuous Run Information 1/16 AIRCRAFT CABLE POWER CORD T5 OR T5HO LAMP 5-3/4 SOCKET COVER STARTER FIXTURE MIDDLE FIXTURE MIDDLE FIXTURE END FIXTURE
TORi Minimalist Linear ARM - Arm Mount Remote Ballast 1. Install J-box with 3-0 mud ring (provided by contractor). Use fixture mounting centers worksheet for location information. Note: It is critical that these dimensions are precisely followed. 2. Install drywall and complete finish work. 3. Slide cover plates over arms. 4. Slide threads through mounting plate, star washer and flat washer. 5. Securely tighten with nut - make sure mounting holes align with mud ring mounting holes. Note: Ensure arms are lined up correctly. 6. Completely wire make-up. 7. Securely mount fixture to wall with provided 8-32 flat undercut head screws. 8. Slide cover plate over mounting plate (magnets will pull the cover plate tight against wall.)
TORi Minimalist Linear SSM - Suspended Surface Mount 1. Drill necessary mounting holes and power feed and mounting in Housing in desired location. 2. Secure whip (by others) to housing 3. Secure housing to mounting surface (fasteners by others). 4. Make up necessary wires and install fixture lid assembly to housing. 5. Snap lid on 6. Install fixture by feeding cable into cable grippers on fixture Housing Fastener (supplied by others) 7. Install lamp and socket covers 8. Install accessory reflectors/lenses if applicable. Aircraft Cable Housing Lid Cable Gripper
TORi IB Minimalist Linear SM - Surface Mount 1-1/8 O SQUARE EXTRUDED HOUSING 2-1/2 T5 OR T5HO LAMP SOCKET COVER 1. Drill necessary mounting holes and power feed hole in mounting plate in desired location. 2. Secure whip (by others) to mounting plate 3. Secure mounting plate to mounting surface (fasteners by others). If wall make sure orientation of mounting plate is such that fixture will swing down to be installed (see illustration below). If mounting to a ceiling make sure to attached safety cables (provided) between mounting plate and fixture housing. 4. Make up necessary wires and install fixture housing assembly to lid. 5. Install lamp and accessory reflectors/lenses if applicable. Housing Mounting Plate
TORi RB Minimalist Linear Lamp Changing Guide PLUNGER SOCKET SOCKET COVER 1. Disconnect from power 2. Unscrew socket covers 3. Release lamp from static socket on opposite side 4. Remove socket covers from the old lamp and slide them on the new lamp. 5. install lamp and screw on socket covers 6. Install lamp and socket covers 7. Depress the plunger socket with lamp Unhook lamp from static socket and lower down Push lamp into plunger socket