Technical Information Plastic Additives TI/EVN 1184 e November 21 Page 1 of 6 = registered Trademark of BASF Specialty Chemicals Holding GmbH Paliotol Yellow K 961 HD General properties Chemical character Chinophthalone Colour Index Part I P. Y. 138 Colour Index Part II 563 CAS Number 3125-47-4 Physical form Powder Color shade Yellow Coloristic properties Hue angle in PVC 1/3 SD 96.7 Chroma in PVC 1/3 SD 79 Red. ratio in PVC 1/3 SD 5.2 Hue angle in PVC 1/9 SD 11 Chroma in PVC 1/9 SD 57.4 Red. ratio in PVC 1/9 SD 2.2 Hue angle in PE-LD 1/3 SD 96.3 Chroma in PE-LD 1/3 SD 78.7 Red. ratio PE-LD 1/3 SD 5.5 Hue angle in PE-LD 1/9 SD 1 Chroma in PE-LD 1/9 SD 57 Red. ratio in PE-LD 1/9 SD 2.8 Ease of dispersion < 1 Physical properties Density 1.8 g/cm³ Bulk density.4 g/cm³ Index of ph 3 5 Conductivity > 5 µs/cm Specific surface 28 m²/g Fastness properties Heat stability 27 C Light fastness 8 Weather fastness see diagram Migration fastness 4 5 Infl. on warping of PE-HD distinct Fastness to chemicals HCl conc. HCl 1 % H 2 SO 4 conc. 5 months H 2 SO 4 1 % HNO 3 1 % NaOH conc. Na 2 CO 3 sat. Criteria for the fastness to chemicals was a possible color change of the colored plastic material during the storage in the test medium.
TI/EVK 1184 e November 21 Page 2 of 6 Recommendations for applications PVC-p PVC-u PUR LD-PE HD-PE PP PS SB SAN ABS/ASA PMMA PC PA PETP CA/CAB UP UCC not not not UCC: Under certain conditions Restrictions for usage Sensitive to alkalis at high temperature Preparations Product Supply form Color strength Content Eupolen PE Yellow 9-611 powder P.Y. 138 5 % Eupolen PE Yellow 9-614 fine pellets P.Y. 138 5 % Eupolen PP Yellow 9-615 pellets P.Y. 138 4 % Euvinyl C Yellow 9-612 coarse powder P.Y. 138 5 % Depending on the suitability of the pigment, single pigment dispersions in polymers like PE, PP, PA, PVC etc. are available upon request. For information please visit www.basf.com/pigment in the internet. Microscopy
TI/EVK 1184 e November 21 Page 3 of 6 1 Particle Size Distribution Preparation: Baking enamel - 6 min Skandex Median Size: 329.85 nm Disc centrifuge 8 Oversize % 6 4 2 5 1 15 2 Diameter nm 1 Reflection 1:1 1:1.2% 8 PVC-p 6 % 4 2 4 45 5 55 6 65 7 Wavelength nm
TI/EVK 1184 e November 21 Page 4 of 6 5 Heat Stability 1:5 1:1 PE-HD (Lupolen 631M) 4 DIN EN 12877-1 3 de* 2 1 2 22 24 26 28 3 32 Temperature C 5 Weather fastness 1:5 1:1.2%.5% 4 PE-HD (Lupolen 631M) DIN EN ISO 4892-2 DIN EN 215-A2 Steps grey scale 3 2 1 5 1 2 3 Time hours
TI/EVK 1184 e November 21 Page 5 of 6 8 Light fastness PE-HD (Lupolen 631M) DIN EN ISO 15-B2 6 Steps blue wool scale 4 2 1:5 1:1.2%.5% Limiting concentration Full Shade Red. Ratio 1:1 32 PE-HD (Lupolen 631M) DIN EN 12877-1 3 Heat Resistance C 28 26 24 22 2 18..2.4.6.8.1 Pigment Concentration %
TI/EVK 1184 e November 21 Page 6 of 6 Note The descriptions, designs, data and information contained herein are presented in good faith, and are based on BASF s current knowledge and experience. They are provided for guidance only, and do not constitute the agreed contractual quality of the product or a part of BASF s terms and conditions of sale. Because many factors may affect processing or application/use of the product, BASF recommends that the reader carry out its own investigations and tests to determine the suitability of a product for its particular purpose prior to use. It is the responsibility of the recipient of product to ensure that any proprietary rights and existing laws and legislation are observed. No warranties of any kind, either expressed or implied, including, but not limited to, warranties of merchantability or fitness for a particular purpose, are made regarding products described or designs, data or information set forth herein, or that the products, descriptions, designs, data or information may be used without infringing the intellectual property rights of others. Any descriptions, designs, data and information given in this publication may change without prior information. The descriptions, designs, data and information furnished by BASF hereunder are given gratis and BASF assumes no obligation or liability for the descriptions, designs, data or information given or results obtained, all such being given and accepted at the reader s risk. November 21 BASF Schweiz AG Performance Chemicals/Plastic Additives Klybeckstrasse 141 457 Basel, Switzerland