MAKING MODERN LIVING POILE Technical Information eries 45 H Frame powersolutions.danfoss.com
Contents Frame H Design... 4 pecifications... 5 Performance H57... 6 Performance H75D... 7 Order code... 8 Controls... 1 Pressure compensated control (PC)... 1 Load sensing control (L)... 1 Load sensing control with internal bleed orifice (L)... 11 Input shafts... 12 Auxiliary mounting pads... 15 AE-A auxiliary mounting pad... 15 AE- auxiliary mounting pad... 15 Displacement limiters... 16 AE-C auxiliary mounting pad... 16 Installation drawings... 17 Adjustable displacement limiter... 17 AE-C mounting flange, axial ported endcap... 18 AE-C mounting flange, radial ported endcap...2 AE- mounting flange, axial ported endcap...22 AE- mounting flange, radial ported endcap... 24 2 1158669 Rev A ep 213
General Information This information was removed from: eries 45 Axial Piston Open Circuit Pumps Technical Information Manual 52L519 Rev E November 26 For more information regarding the eries 45 product line refer to the current version of 52L519. 1158669 Rev A ep 213 3
Frame H Design eries 45 Frame H pumps have a dual servo piston design with a cradle-type swashplate set in polymer-coated journal bearings. The bias piston increases swashplate angle. The displacement piston decreases swashplate angle. At equal pressure, the larger diameter displacement piston overpowers the bias piston. Nine reciprocating pistons displace fluid from the pump inlet to the pump outlet as the cylinder block rotates on the pump input shaft. The block spring holds the piston slippers to the swashplate via the slipper retainer. The cylinder block rides on a bi-metal valve plate optimized for high volumetric efficiency and low noise. Tapered roller bearings support the input shaft and a viton lip-seal protects against shaft leaks. An integral, adjustable, two-stage control senses system pressure (PC and L controls) and load pressure (L only). The pump control ports system pressure to the displacement piston to control pump output flow. Frame H cross section PC cartridge Integral pump control L adjustment PC adjustment L spool Displacement piston Tapered roller bearing Cylinder block haft seal Valve plate Input shaft washplate lipper lipper retainer ias piston ias spring Piston Tapered roller bearing P11 984E 4 1158669 Rev A ep 213
pecifications Features and options Model Feature Unit H57 H75D For general operating parameters, including fluid viscosity, temperature, and inlet and case pressures, see page 14. For system design parameters, including installation, filtration, reservoir, and line velocities, see page 16. Maximum Displacement cm³ [in³] 57 [3.48] 75 [4.58] Flow at rated speed (theoretical) Input torque at maximum displacement (theoretical) Mass moment of inertia of internal rotating components l/min [U gal/min] N m/bar [lbf in/1 psi] kg m² [slug ft²] 148.2 [39.2].97 [554].43 [.318] 18 [47.5] 1.194 [729].42 [.31] Weight Axial ports kg [lb] 24 [53] Radial ports 27 [6] Rotation Clockwise, Counterclockwise Mounting Auxiliary mounting (ee page 51) ystem ports (type) ystem ports (location) Control types (ee page 46) AE-, AE-C AE-A, AE-, AE-, AE-C AE O-ring boss, 4-bolt split flange Axial, Radial PC, L, L with internal bleed hafts (ee page 48) plined 13 tooth, 14 tooth, 15 tooth Displacement limiters (ee page 52) Tapered traight Ø 31.75 mm [1.25 in], 1:8 taper Ø 31.75 mm [1.25 in] Optional, adjustable For definitions of pressure and speed ratings, see page 15. For more information on external shaft loads, see page 17; mounting flange loads, see page 18. Ratings Model Rating Units H57 H75D Input speed¹ minimum min -1 (rpm) 5 5 continuous 26 24 maximum 32 28 Working pressure continuous bar [psi] 31 [4495] 21 [345] External shaft loads maximum 4 [58] 3 [435] External moment (M e ) N m [lbf in] 226 [2] 226 [2] Thrust in (T in ), out (T out ) N [lbf] 22 [495] 22 [495] earing life at 14 bar [23 psi] 1 hours 29 712 1 755 Mounting flange load moments at 21 bar [345 psi] 6834 2474 at 26 bar [377 psi] 3151 at 31 bar [4495 psi] 1666 Vibratory (continuous) N m [lbf in] AE-C: 15 [14 ], AE-: 735 [65] hock (max) AE-C: 565 [5 ], AE-: 26 [23 ] 1. Input speeds are valid at 1 bar absolute [ in Hg vac] inlet pressure. ee Inlet pressure vs. speed charts. ound levels² For more information on noise levels, see page 2. d(a) 21 bar [345 psi] 26 bar [377 psi] 31 bar [4495 psi] Model 18 min -1 (rpm) Rated speed 18 min -1 (rpm) Rated speed 18 min -1 (rpm) Rated speed H57 69 72 7 73 71 74 H75D 71 74 2. ound data was collected in a semi-anechoic chamber. Values have been adjusted (-3 d) to reflect anechoic levels. 1158669 Rev A ep 213 5
Performance H57 Flow vs. speed 2 5 Flow and power data valid at 49 C [12 F] and viscosity of 17.8 mm²/sec [88 U]. Flow (l/min) 16 12 8 4 4 3 2 1 Flow (U gal/min) Input power vs. speed 12 5 1 15 2 25 3-1 peed min (rpm) P14 2E 16 Power (kw) 1 8 6 4 2 28 bar [461 psi] 21 bar [345 psi] 14 bar [23 psi] 14 12 1 8 6 4 2 Power (hp) The chart on the right shows allowable inlet pressure and speed at various displacements. Greater speeds and lower inlet pressures are possible at reduced displacement. Operating outside of acceptable limits reduces pump life. 5 1 15 2 25 3-1 peed min (rpm) Inlet pressure vs. speed Inlet Pressure (bar abs) 1.6 1.5 1.4 1.3 1.2 1.1 1..9.8.7.6 22 24 26 28 3 32 34-1 haft peed min (rpm) P14 21E 1% 9% 8% 8 6 4 2 3 6 9 (psi gauge) (in Hg vac) P11 987E 6 1158669 Rev A ep 213
Performance H75D Flow and power data valid at 49 C [12 F] and viscosity of 17.8 mm²/sec [88 U]. Flow vs. speed Flow (l/min) 25 2 15 1 5 6 5 4 3 2 1 Flow (U gal/min) Input power vs. speed 5 1 15 2 25-1 peed min (rpm) P11 985E 1 Power (kw) 8 6 4 2 21 bar [345 psi] 14 bar [23 psi] 12 1 8 6 4 2 Power (hp) 5 1 15 2 25-1 peed min (rpm) P11 986E The chart on the right shows allowable inlet pressure and speed at various displacements. Greater speeds and lower inlet pressures are possible at reduced displacement. Operating outside of acceptable limits reduces pump life. Inlet pressure vs. speed Inlet Pressure (bar abs) 1.6 1.5 1.4 1.3 1.2 1.1 1..9.8.7 1% 9% 8%.6 2 22 24 26 28 3-1 haft peed min (rpm) 8 6 4 2 3 6 9 (psi gauge) (in Hg vac) P14 14E 1158669 Rev A ep 213 7
Order Code R P C D E F G H 1 2 3 1 2 3 L M N J K R Product HR H Frame, variable displacement open circuit pump Rotation L R Left hand (counterclockwise) Right hand (clockwise) P Displacement and pressure rating 57 57 cm³/rev [3.48 in³/rev], 31 bar [4495 psi] continuous working pressure 75D 75 cm³/rev [4.58 in³/rev], 21 bar [345 psi] continuous working pressure C Control type PC Pressure compensated control L Load sensing / pressure compensating control L Load sensing / pressure compensating control with internal bleed orifice D PC setting (2 digit code, 1 bar increments) Example 1 = 1 bar 1 31 1 to 31 bar [145 to 4495 psi] (57) 1 21 1 to 21 bar [145 to 345 psi] (75D) E Load sensing setting (2 digit code, 1 bar increments) Example 2 = 2 bar 1 35 1 to 35 bar [145 to 58 psi] NN Not applicable (use with PC controls) F Not used NN Not applicable G Pilot orifice N None (standard for PC control) A Ø.8 mm [.31 in] (standard with L and L controls) H Gain orifice 3 tandard orifice 8 1158669 Rev A ep 213
Order Code (continued) R P C D E F G H 1 2 3 1 2 3 L M N J K J1 Input shaft AE-C mounting flange pumps (housing code K2=1) 1 14 tooth, 12/24 pitch (ANI 92.1 197 - Class 5) T K4 Ø 31.75 mm [1.25 in], 1:8 taper Ø 31.75 mm [1.25 in], straight keyed C2 13 tooth, 16/32 pitch (ANI 92.1 197 - Class 5) C3 15 tooth, 16/32 pitch (ANI 92.1 197 - Class 5) L4 AE- mounting flange pumps (housing code K2=6) Ø 31.75 mm [1.25 in], straight keyed D2 13 tooth, 16/32 pitch (ANI 92.1 197 - Class 5) D3 15 tooth, 16/32 pitch (ANI 92.1 197 - Class 5) J2 N A T V C J3 Auxiliary mounting flange None AE-A, 9-tooth coupling AE-A, 11-tooth coupling AE-, 13-tooth coupling AE-, 15-tooth coupling AE-C, 14-tooth coupling ystem port size and location Code Location Port type Inlet size Outlet size 2 Radial 4-bolt split-flange 2 in. 1 in. 4 Axial 4-bolt split-flange 2 in. 1 in. 3 Axial AE O-ring boss 1 7 /8 in. 1 5 /16 in. K1 haft seal A ingle lip seal, viton K2 Mounting flange and housing port style 1 AE-C 4-bolt, AE O-ring boss housing ports 6 AE- 2-bolt, AE O-ring boss housing ports K3 Not used L N Not applicable Displacement limiter NNN AAA Axx None Adjustable, factory set at max angle Adjustable, factory set at xx% of maximum displacement (5% increments), Example: A9=9% M pecial hardware NNN None N pecial features NNN None 1158669 Rev A ep 213 9
Controls pecifications Pressure compensated control (PC) PC control setting range Model bar psi H57 1 31 145 4495 H75D 1 21 145 345 Response/recovery times* (ms) Response Recovery H57 3 125 H75D 3 13 * For definitions, see page 11. chematic diagram PC schematic L2 M2 X Legend = Outlet = Inlet L1, L2 = Case drain M2 = ystem pressure gauge port M4 = ervo pressure gauge port X = Not used M4 L1 P11 989 Load sensing control (L) pecifications PC setting range Model bar psi H57 1 31 145 4495 H75D 1 21 145 345 Response/recovery times* (ms) Response Recovery H57 3 9 H75D 3 95 * For definitions, see page 13. chematic diagram L chematic L setting range L2 X Model bar psi All 1 35 145 58 M2 M4 Legend = Outlet = Inlet L1, L2 = Case drain M2 = ystem pressure gauge port M4 = ervo pressure gauge port X = L signal port L1 1 1158669 Rev A ep 213
Controls (continued) pecifications Load sensing control with internal bleed orifice (L) PC setting range Response/recovery times* Model bar psi (ms) Response Recovery H57 1 31 145 4495 H57 3 9 H75D 1 21 145 345 H75D 3 95 * For definitions, see page 13. chematic diagram L chematic L setting range L2 X Model bar psi All 1 35 145 58 M2 L1 M4 P11 991 Legend = Outlet = Inlet L1, L2 = Case drain M2 = ystem pressure gauge port M4 = ervo pressure gauge port X = L signal port 1158669 Rev A ep 213 11
Input hafts haft data Code 1 Description 14 tooth spline 12/24 pitch (ANI 92.1 197 - Class 5) Availability AE-C flange AE- flange Torque rating¹ Continuous N m [lbf in] Maximum N m [lbf in] 283 [25] 734 [6495] Drawing 47.6 ±.6 [1.87 ±.2] 29.634 [1.1667] PITCH DIA 14 TEETH.12/24 PITCH 3 PREURE ANGLE FILLET ROOT IDE FIT COMPATILE WITH ANI 92.1-197 CLA 5 ALO MATE WITH FLAT ROOT IDE FIT 27.6 [1.9] MAX 31.14 ±.8 [1.23 ±.3] 28 ±.15 [1.1 ±.6] 8 ±.8 [.31 ±.3] COUPLING MUT NOT PROTRUDE EYOND THI POINT P14 27E T Ø 31.75 mm [1.25 in] 1:8 taper (AE J51) N/A 734 [6495] 62 [2.44] REF 42.9 ±.3 [1.69 ±.1] 22.4 ±.4 [.88 ±.2] GAUGE DIA. WOODRUFF KEY +.3 7.887 [.315 +.1. ] Ø31.8 -.25. [ 1.25 -.1 ] 1.-2UNEF-2A THD 3.2 [1.19] GAUGE 125 TAPER PER METER COMPATILE WITH AE TANDARD J51 31.8[1.25] NOMINAL HAFT DIA 8 ±.8 [.31 ±.3] COUPLING MUT NOT PROTRUDE EYOND THI POINT P14 28E K4 Ø 31.75 mm [1.25 in] traight keyed N/A 655 [5797] 56 [2.2] REF 47.6 ±.6 [1.87 ±.2] 7.94 + -.5 [.313 + -.2 ] QUARE KEY x 28.56 LONG [1.125] 31.72 +.2 -.25 [1.25 +.1 -.1 ] 35.2 ±.13 [1.39 ±.1] 8 ±.8 [.31 ±.3] COUPLING MUT NOT PROTRUDE EYOND THI POINT P14 29E 1. ee Input shaft torque ratings, page 19 for definitions of continuous and maximum torque. 12 1158669 Rev A ep 213
input hafts (continued) Code C2 Description 13-tooth 16/32 pitch (ANI 92.1 197 - Class 5) Availability AE-C flange AE- flange Torque rating¹ Continuous N m [lbf in] Maximum N m [lbf in] 12 [9] 282 [2495] Drawing 33.3 [1.31] 2.638 [.813] PITCH DIA. 13 TEETH, 16/32 PITCH 3 PREURE ANGLE FILLET ROOT IDE FIT COMPATILE WITH ANI 92.1-197 CLA 5 ALO MATEWITH FLAT ROOT IDE FIT 18.5 [.73] MAX 22.13 ±.9 [.87 ±.4] 16.7±.5 [.66±.2] 8 ±.8 [.31 ±.3] COUPLING MUT NOT PROTRUDE EYOND THI POINT P14 3E C3 15-tooth 16/32 pitch (ANI 92.1 197 - Class 5) 192 [17] 362 [32] 38 [1.5] 23.813 [.938] PITCH DIA. 15 TEETH, 16/32 PITCH 3 PREURE ANGLE FILLET ROOT IDE FIT COMPATILE WITH ANI 92.1-197 CLA 5 ALO MATEWITH FLAT ROOT IDE FIT 21.84 [.86] MAX 25.34 ±.13 [.998 ±.5] 22.36 ±.5 [.88 ±.2] 8 ±.8 [.31 ±.3] COUPLING MUT NOT PROTRUDE EYOND THI POINT P14 31E L4 Ø 31.75 mm [1.25 in] traight keyed N/A 655 [58] 56 [2.2] REF 47.6 ±.6 [1.87 ±.2] 7.94 + -.5 [.313 + -.2 ] QUARE KEY x 28.56 LONG [1.125] 31.72 +.2 -.25 [1.25 +.1 -.1 ] 35.2 ±.13 [1.39 ±.1] 8 ±.8 [.31 ±.3] COUPLING MUT NOT PROTRUDE EYOND THI POINT P14 29E 1. ee Input shaft torque ratings, page 19 for definitions of continuous and maximum torque. 1158669 Rev A ep 213 13
input hafts (continued) Code D2 Description 13-tooth 16/32 pitch (ANI 92.1 197 - Class 5) Availability AE-C flange AE- flange Torque rating¹ Continuous N m [lbf in] Maximum N m [lbf in] 12 [9] 282 [2495] Drawing 33.3 [1.31] 2.638 [.813] PITCH DIA. 13 TEETH, 16/32 PITCH 3 PREURE ANGLE FILLET ROOT IDE FIT COMPATILE WITH ANI 92.1-197 CLA 5 ALO MATEWITH FLAT ROOT IDE FIT 18.5 [.73] MAX 22.13 ±.9 [.87 ±.4] 16.7±.5 [.66±.2] 8 ±.8 [.31 ±.3] COUPLING MUT NOT PROTRUDE EYOND THI POINT P14 3E D3 15-tooth 16/32 pitch (ANI 92.1 197 - Class 5) 192 [17] 362 [32] 38 [1.5] 23.813 [.938] PITCH DIA. 15 TEETH, 16/32 PITCH 3 PREURE ANGLE FILLET ROOT IDE FIT COMPATILE WITH ANI 92.1-197 CLA 5 ALO MATEWITH FLAT ROOT IDE FIT 21.84 [.86] MAX 25.34 ±.13 [.998 ±.5] 22.36 ±.5 [.88 ±.2] 8 ±.8 [.31 ±.3] COUPLING MUT NOT PROTRUDE EYOND THI POINT P14 31E 1. ee Input shaft torque ratings, page 19 for definitions of continuous and maximum torque. 14 1158669 Rev A ep 213
Auxiliary Mounting Pads AE-A auxiliary mounting pad Dimensions COUPLING-AE A-11T: 11 TOOTH PLINE, 16/32 PITCH 17.463 (.6875) PITCH Ø FILLET ROOT IDE FIT PER ANI 92.1-197, CLA 6 ee page 19 for mating pump pilot and spline dimensions. (2x).375-16 UNC-2 THD 17.8 [.7] MIN THREAD DEPTH 16.4 [4.19] 53.2 [2.9] COUPLING-AE A: 9 TOOTH PLINE, 16/32 PITCH 14.288 [.5625] PITCH Ø FILLET ROOT IDE FIT PER ANI 92.1-197 CLA 6 A MIN COUPLING CLEARANCE MOUNTING FLANGE 298.8 [11.76] AE- mount pumps 268.8 [1.58] AE-C mount pumps Ø88.62 [3.489] Ø82.6 +.8 3.252 +.3 [ ] R.51 MAX [.2] pecifications Coupling 9-tooth 11-tooth pline minimum 13.5 mm [.53 in] 15 mm [.59 in] engagement Continuous 51 N m [45 lbf in] 9 N m [8 lbf in] torque Maximum torque 17 N m [95 lbf in] 147 N m [13 lbf in] Dimension A 21.1 mm [.83 in] 16.1 mm [.63 in] O-RING EAL REQUIRED 1.95 REF 82.27 [3.239] I.D.X [.77] 2.62 [.13] CRO ECTION 58.5 [2.3] MIN HAFT CLEARANCE P14 39E ee page 19 for mating pump pilot and spline dimensions. AE- auxiliary mounting pad Dimensions (2x).5-13 UNC-2 THD THRU 19.7 [.76] MIN THD DEPTH 174. [6.85] 87. [3.43] COUPLING-AE -: 15 TOOTH PLINE, 16/32 PITCH 23.813 [.9375] PITCH Ø FILLET ROOT IDE PER ANI 92.1-197 CLA 6 COUPLING-AE : 13 TOOTH PLINE, 16/32 PITCH 2.638 [.8125] PITCH Ø FILLET ROOT IDE PER ANI 92.1-197 CLA 6 A MIN COUPLING CLEARANCE MOUNTING FLANGE 294.4 [11.59] AE- mount pumps 264.4 [1.41] AE-C mount pumps 15.64 [4.159] +.8 11.65 - +.3 [4.2 - ] R.51 [.2] pecifications 146. [5.75] Coupling 13-tooth 15-tooth pline minimum 14.2 mm [.56 in] 18.9 mm [.74 in] engagement Continuous 124 N m [11 lbf in] 235 N m [28 lbf in] torque Maximum torque 249 N m [22 lbf in] 339 N m [3 lbf in] Dimension A 2.7 mm [.81 in] 12.7 mm [.5 in] O-RING EAL REQUIRED REF 11.32 [3.989] I.D. 1.78 [.7] CRO ECTION 1.24 [.49] 11. [.433] 54.1 [2.13] MIN HAFT CLEARANCE P14 4E 1158669 Rev A ep 213 15
Auxiliary Mounting Pads (continued) ee page 19 for mating pump pilot and spline dimensions. AE-C auxiliary mounting pad Dimensions (4x).5-13 UNC-2 THD THRU 22.7 [.89] MIN THD DEPTH 73.3 [2.88] 146.5 [5.77] COUPLING-AE C: 29.633 [1.1667] PITCH Ø 14 TOOTH PLINE, 12/24 PITCH FLAT ROOT IDE FIT PER ANI 92.1-197 CLA 6 9 [.35] MIN COUPLING CLEARANCE MOUNTING FLANGE 297.4 [11.71] AE- mount pumps 267.4 [1.53] AE-C mount pumps 114.5 [4.51] 57.2 [2.25] Ø131.57 [5.18] Ø127.3 +.5 +.2 [5.1 ] R.51 MAX [.2] pecifications 57.3 [2.25] 114.5 [4.51] O-RING EAL REQUIRED 1.3 REF 12.37 [4.379] I.D. X [.5] 1.78 [.7] CRO ECTION 13.8 MIN [.54] 57.1 [2.25] MIN HAFT CLEARANCE P14 41E Coupling pline minimum engagement Continuous torque Maximum torque 14-tooth 18.3 mm [.72 in] 235 N m [28 lbf in] 339 N m [3 lbf in] Displacement Limiters H Frame open circuit pumps are available with an optional adjustable displacement limiter. This adjustable stop limits the pump s maximum displacement. Displacement limiter cross-section etting range H57 H75D 43 to 57 cm³ [ 2.61 to 3.48 in³] 56 to 75 cm³ [3.43 to 4.58 in³] P14 26 16 1158669 Rev A ep 213
Installation Drawings Adjustable displacement limiter 221.2 MAX [8.32] AE-C MOUNT PUMP 241.2 MAX [8.32] AE- MOUNT PUMP 221.2 MAX [8.32] AE-C MOUNT PUMP 241.2 MAX [8.32] AE- MOUNT PUMP 92.4 MAX [3.64] 92.4 MAX [3.64] P14 7E Axial ported units Radial ported units 1158669 Rev A ep 213 17
Installation Drawings (continued) AE-C mounting flange, axial ported endcap ERVO PREURE GAGE PORT M4 AE J1926/1:.4375-2 L TANDY PREURE ADJUTMENT CAE DRAIN PORT L2 Counterclockwise rotation 18. [.71] 63. [2.48] YTEM PORT (INLET PORT) AE J1926/1: 1.875-12 YTEM PORT (OUTLET PORT) AE J1926/1: 1.3125-12 L IGNAL PORT X 67. [2.64] PC PREURE ADJUTMENT REMOTE PC PORT 122.2 [4.81] Clockwise rotation L IGNAL PORT X (PLUGGED FOR PC CONTROL) AE J1926/1:.4375-2 21.5 [8.29] 115.7 [4.56] 36.2 [1.43] 44.5 [1.75] 15.8 [.62] 4X R1. [R.4] 86.8 [3.42] YTEM PORT (INLET PORT) 2.-3 PI PLIT FLANGE O PER AE J518 (CODE 61) Clockwise rotation YTEM PORT (OUTLET PORT) 1.-5 PI PLIT FLANGE O PER AE J518 (CODE 61) EXCEPT 18.6 [.73] MIN. FULL THD. 215. [8.46] 16.8 [4.2] 73. [2.87] CAE DRAIN PORT L1 AE J1926/1:.875-14 95. [3.74] TO C.G. Ø126.974±.25 [4.999±.1] 12.7 [.5] 18. [4.25] 144. [5.67] 72. [2.83] Counterclockwise rotation P14 61E Third-angle projection mm [in] 18 1158669 Rev A ep 213
Installation Drawings (continued) AE-C mounting flange, axial ported endcap (continued) 114.5 [4.51] CAE DRAIN PORT L2 AE J1926/1:.875-14 57.3 [2.25] 68. [2.68] CW CCW 57.25 [2.25] 114.5 [4.51] 73. [2.88] 63. [2.48] Ø14.3 [Ø.56] YTEM PREURE GAGE PORT M2 AE J1926/1:.4375-2 CAE DRAIN PORT L1 P14 61E Third-angle projection mm [in] 1158669 Rev A ep 213 19
Installation Drawings (continued) AE-C mounting flange, radial ported endcap ERVO PREURE GAGE PORT M4 AE J1926/1:.4375-2 L TANDY PREURE ADJUTMENT CAE DRAIN PORT L2 18. [.71] 63. [2.48] L IGNAL PORT X 67. [2.64] 122.2 [4.81] PC PREURE ADJUTMENT REMOTE PC PORT 246.8 [9.72] 82. [3.23] 75. [2.95] L IGNAL PORT X (PLUGGED FOR PC CONTROL) AE J1926/1:.4375-2 115.7 [4.56] 15.8 [.62] 4X R1. [.4] 86.8 [3.42] 215. [8.46] Ø126.975±.25 [4.999±.1] 16.8 [4.2] 73. [2.87] Clockwise rotation YTEM PORT (OUTLET PORT) 1.-5 PI PLIT FLANGE O PER AE J518 (CODE 61) EXCEPT 18.6 [.73] MIN. FULL THD. CAE DRAIN PORT L1 AE J1926/1:.875-14 18. [4.25] 12.7 [.5] 11. [4.33] TO C.G. 198. [7.8] OUTLET 75. [2.95] INLET 82. [3.23] Counterclockwise rotation P14 62E Third-angle projection mm [in] 2 1158669 Rev A ep 213
Installation Drawings (continued) AE-C mounting flange, radial ported endcap (continued) 114.5 [4.51] CAE DRAIN PORT L2 AE J1926/1:.875-14 57.25 [2.25] 68. [2.68] 57.25 [2.25] 114.5 [4.51] 73. [2.87] Ø14.3 [.56] 63. [2.48] CAE DRAIN PORT L1 26.5 [8.13] YTEM PREURE GAGE PORT M2.4375-2 TR-THD O-RING O YTEM PORT (INLET PORT) 2.-3 PI PLIT FLANGE O PER AE J518 (CODE 61) P14 62E Third-angle projection mm [in] 1158669 Rev A ep 213 21
Installation Drawings (continued) AE- mounting flange, axial ported endcap ERVO PREURE GAGE PORT M4 AE J1926/1:.4375-2 L TANDY PREURE ADJUTMENT CAE DRAIN PORT L2 63. [2.48] Counterclockwise rotation L IGNAL PORT X 67. [2.64] YTEM PORT (INLET PORT) AE J1926/1: 1.875-12 YTEM PORT (OUTLET PORT) AE J1926/1: 1.3125-12 PC PREURE ADJUTMENT L IGNAL PORT X (PLUGGED FOR PC CONTROL) AE J1926/1:.4375-2 24.5 [9.47] 36.2 [1.43] YTEM PORT (INLET PORT) 2.-3 PI PLIT FLANGE O PER AE J518 (CODE 61) Clockwise rotation 44.5 [1.75] YTEM PORT (OUTLET PORT) 1.-5 PI PLIT FLANGE O PER AE J518 (CODE 61) EXCEPT 18.6 [.73] MIN. FULL THD. 215. [8.46] 86.8 [3.42] 145.7 [5.74] 15.8 [.62] 4X R1. [R.4] Ø11.575±.25 [3.999±.1] 16.8 [4.2] 73. [2.87] Clockwise rotation CAE DRAIN PORT L1 AE J1926/1:.875-14 125. [4.92] TO C.G. 138. [5.43] 9.7 [.38] 144. [5.67] 72. [2.83] Counterclockwise rotation P14 63E Third-angle projection mm [in] 22 1158669 Rev A ep 213
Installation Drawings (continued) AE- mounting flange, axial ported endcap (continued) CAE DRAIN PORT L2 AE J1926/1:.875-14 Ø14.3 [Ø.56] 98. [3.86] 73. [2.87] 73. [2.87] CW CCW 146. [5.75] 63. [2.48] CAE DRAIN PORT L1 YTEM PREURE GAGE PORT M2 AE J1926/1:.4375-2 P14 63E Third-angle projection mm [in] 1158669 Rev A ep 213 23
Installation Drawings (continued) AE- mounting flange, radial ported endcap L2 M2 Clockwise rotation Counterclockwise rotation Third-angle projection mm [in] 24 1158669 Rev A ep 213
Installation Drawings (continued) AE- mounting flange, radial ported endcap (continued) X M4 Third-angle projection mm [in] 1158669 Rev A ep 213 25
Products we offer: ent Axis Motors Closed Circuit Axial Piston Pumps and Motors Displays Electrohydraulic Power teering Electrohydraulics Hydraulic Power teering Integrated ystems Joysticks and Control Handles Microcontrollers and oftware Open Circuit Axial Piston Pumps Orbital Motors PLU+1 GUIDE Proportional Valves ensors teering Transit Mixer Drives Danfoss Power olutions is a global manufacturer and supplier of high-quality hydraulic and electronic components. We specialize in providing state-of-the-art technology and solutions that excel in the harsh operating conditions of the mobile off-highway market. uilding on our extensive applications expertise, we work closely with our customers to ensure exceptional performance for a broad range of off-highway vehicles. We help OEMs around the world speed up system development, reduce costs and bring vehicles to market faster. Danfoss Your trongest Partner in Mobile Hydraulics. Go to www.powersolutions.danfoss.com for further product information. Wherever off-highway vehicles are at work, so is Danfoss. We offer expert worldwide support for our customers, ensuring the best possible solutions for outstanding performance. And with an extensive network of Global ervice Partners, we also provide comprehensive global service for all of our components. Please contact the Danfoss Power olution representative nearest you. Comatrol www.comatrol.com chwarzmüller-inverter www.schwarzmuellerinverter.com Turolla www.turollaocg.com Valmova www.valmova.com Hydro-Gear www.hydro-gear.com Daikin-auer-Danfoss www.daikin-sauer-danfoss.com Local address: Danfoss Power olutions U Company 28 East 13th treet Ames, IA 51, UA Phone: +1 515 239 6 Danfoss Power olutions GmbH & Co. OHG Krokamp 35 D-24539 Neumünster, Germany Phone: +49 4321 871 Danfoss Power olutions Ap Nordborgvej 81 DK-643 Nordborg, Denmark Phone: +45 7488 2222 Danfoss Power olutions 22F, lock C, Yishan Rd hanghai 2233, China Phone: +86 21 3418 52 Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/. All rights reserved. 1158669 Rev A ep 213 www.danfoss.com Danfoss A/, 213-9