MODERN TECHNOLOGY IN PUNCHING AND SHEARING SOLUTION The GEKA HYDRACROP range of hydraulic steelworkers have been designed by highly experienced engineers with the support of powerful CAD equipment, culminating in the most efficient and practical way of shearing, punching and bending pf flats and sections. Ideal There are 5 working stations actuated by two hydraulic cylinders (one positioned at each end of the main frame) prepared for producing different functions without tool changing, with simultaneous or independent operations. Economics GEKA production engineers have developed a most sotisficated manufacturing facility occupying an area of 15.000m 2 under one roof with a force of 80 personnel, achieving the best of quality by applying the latest advanced technology including robots, thus allowing our range of machines to be built with the most cost productive results. Proudly our motto is To produce a high quality machine at a reasonable price and of the most modern design.
Of rational desing - Blade holder supported at both ends. - Monoblock frame. - Hydraulic equipment package. - Wide space for mounting special equipment - Electric cabinet including safety and operation control.
Important points Punching The use of a separate, double-acting hydraulic cylinder for power at this station creates an independent work station with large die space for standard and special tooling. 1. Cylinder support. 2. Sectionalized cylinder (110 S). 3. Stroke adjusting stop. 4. Ample stroke for punching, bending, countersinking and forming. 5. Face of punch cylinder machined and guided to prevent misalignment of cylinder shaft under load. 6. Extra guide to better absorb offcenter loads and thus better protect hydraulic seals. 7. Cylinder prepared for shaped and special tooling. 8. Rapid tool-change. 9. Adjustable punch stripper 10. Gauging table with milimeter scales (included in productivity package ). 11. Positioning stop up to 500 mm. 12. Gooseneck die-holder for punching plates and sections, especially channels and beams in the flange. 13. Bolts for front-to-back alignment. 14. Bolts for left to right alignment. 15. Bolt for mounting gooseneck die holder support block.
angle cutting To succeed in cutting angle section without deformation, GEKA HYDRACROP machines are manufactured with a patented system whereby the upper blade follows a rectilinear movement throughout the stroke of the machine cutting angles from maximum to minimum capacity free of deformation and with no material loss (simple cut). With the use of our patented system and the radial movement of the arm a tonnage multiplication is achieved (110 tons in the case of the Hyd-55) making this a most efficient means of obtaining a clean smooth cut without deformation. 1. Blade-gap adjustment bolts. 2. Adjustable angle guide. 3. Upper blade guide. 4. Upper blade for distortion-free cut. 5. Safety guard.
cutting of flats High stability of the main monoblock blade-holder, controlled at both ends, allows for large capacity cutting of flats. The upper blade has been geometrically designed with consideration of having a radial force multiplying system resulting in cuts of the highest quality. 1. Lower blade (four cutting edges). 2. Special geometric upper blade. 3. Blade gap adjustments. 4. Upper blade control supplement for deformation free cut. 5. Right and left hand adjustable guide bars to 45º 6. Support table for cutting of flats. 7. Guide positioning slot for full cutting length. 8. Guide plate hold down stud. 9. Slide adjustment main blade-holder.
Round and square and section shearing station The GEKA HYDRACROP machines are equipped in their standard version with blades for round and square cutting. This station has also been designed with an eye to the cutting of special sections such as Channels, Beams, Z, for which we have available an ample stock of blades. Blades can be changed quickly by removing and then replacing only 4 bolts. 1. Guide plate height positioning screw. 2. Blade retaining block. 3. Guide plate retaining stud.
Notching station 1. Rectangular punch 2. Stripper arms. 3. Transverse adjustment of die base. 4. Frame pre-drilled for special accessories. 5. Rectangular notching base. 6. Support table with graduated stops, included in the Production package. As this station has been designed with upper and lower stroke adjustments and inching, a number of additional optional and special attachments can be fitted: Triangular notching. Punching equipment. Rounding ends of flats. Rounding of corners. Rounding of footing, etc
For greater and more-efficient production To address the concern for both highest quality and an acceptable price. GEKA prepares its machines for mounting the Production package, at extremely low price, including: Quality notching table with graduated stop bar The guard is open Quality punching table with graduated stop bar Machine light Universal electric auto bar stop Set of ten (10) standard round punches and dies.
Maximum safety All HYDRACROP machines are equipped with safety guarding, thus offering maximum protection for the operators at all times. We ask you not to remove them.
Complete Range Of 2 Cylinder Shearing And Punching Machines. - 5 SIZES HYDRACROP 55/110 80/150 110/180 The first number shows metric tons on the punching station. The second number, on the angle cutting station. 165/300 220/300-3 SERIES OF MACHINES A, S, SD ARE AVAILABLE SERIE A Machines driven by 2 cylinders. 5 working stations, prepared with tooling for the cutting of angles, flats, round and square bars, rectangular notching and punching. Rapid tool change Support table with angular positioning stops for the cutting of flats. 2 simultaneous working stations. SERIE S As the A series plus the following additional equipment as standard: High speed hydraulic system. Special approach equipment, at reduced pressure and low speed. Machines prepared for mounting the Production package including: o Precision punching table with milimeter stops. o Precision notching table with milimeter stops. o Universal electric bar stop. o Machine light for improved vision at work station. o 10 sets of round punches and dies. SERIE SD This machine includes the same additions as the S series, and an extended punching throat for large area flat plate working.
Hydracrop 55/110 Significant capacities mm.s inches Flat shear capacity 300x15 200x20 12 x ⅝ 8 x3/4 Shear for angles without distortion: 120x120x10 4 x4 x½ Shear for angles 130x130x13 5 x5 x½ with optional blade(small distortion) Cropper for Ø & 40mm 1 9/16 Punching capacity Ø 40x10 1½ x⅜ Hydracrop 80/150 Significant capacities mm.s inches Flat shear capacity 450x15 300x20 18 x⅝ 12 x ¾ Shear for angles without distortion: 130x130x13 5 x5 x½ Shear for angles 150x150x13 6 x6 x½ with optional blade(small distortion) Cropper for Ø & 45mm 1¾ Punching capacity Ø 40x14 1½ x9/16
Hydracrop 110/180 Significant capacities: Flat shear capacity Shear for angles without distortion: Shear for angles with optional blade(small distortion) mm.s 600x15 400x20 150x150x13 160x160x13 inches 24 x⅝ 16 x ¾ 6 x6 x½ 6 x6 x⅝ Cropper for Ø & 50mm 2 Punching capacity Ø 40x20 1½ x¾ Hydracrop 165/300 Significant capacities: Flat shear capacity mm.s 750x20 400x30 205x205x18 inches 30 x¾ 16 x1⅛ 8 x8 x¾ Shear for angles without distortion: Shear for angles 205x205x25 8 x8 x1 with optional blade(small distortion) Cropper for Ø & 60mm 2¾ Punching capacity Ø 40x32 1½ x1¼
Optional equipment Knowing the universality of Hydraulic Punching and Shearing machines, GEKA, have a complete range of optional equipment. For a more information please ask for an accessories catalogue: CNC gauge table Semi Paxy 1000. Oversize punching equipment with table. Multistop table Index rail for punching station. Views with protection guard removed. Post sale service GEKA has a compete network of concessionaries in more than 50 countries that will try hard to find a solution for all the cutting and punching problems, looking after the maintenance of all existent equipment, negotiating all rechange tools, original punches and dies, etc. We are sure that the professional advice will be useful.
SHEAR FOR FLATS Flats... mm. CHARACTERISTICS HYDRACROP MODELS IN mm.s 55/110 80/150 110/180 165/300 220/300 300 x15 200 x 20 450x15 300x20 600x15 400x20 750x20 400x30 750x20 400x30 Length of blades mm. 305 475 605 765 765 Square bar... mm. 25 --- --- --- --- Working height... mm. 880 850 960 870 870 Cutting an L-iron leg at 45º 60 80 100 120 120 SHEAR FOR SECTION IRON Angle station... KN 1.100 1.500 1.800 3.000 3.000 L at Right Angle º (non 120x120x10 130x130x13 152x152x13 205x205x18 205x205x18 deformation sys) mm. L at 45º... mm. 70x70x7 70x70x7 70x70x7 70x70x7 70x70x7 WITH SPECIAL BLADES L at 90º 130x130x13 152x152x13 160x160x16 205x205x25 205x205x25 BAR CROPPER Round bar Ø...mm. 40 45 50 60 60 Square bar...mm. 40 45 50 60 60 WITH SPECIAL BLADES Channels UPN.. mm. 120 140 180 200 200 Beams IPN...mm. 120 140 180 200 200 NOTCHER Sheet metal... mm. 10 12 13 16 16 L Iron... mm. 100 100 100 120 120 Depth... mm. 90 90 90 110 110 Width...mm. 42 52 52 58 58 PUNCHING TOOL Power. KN 550 800 1.100 1.650 2.200 Max. Capacity with quick change system.mm. Ø40x10 Ø20x20 Ø40x14 Ø24x24 Ø40x20 Ø28x28 Ø40x30 Ø34x34 Ø40x40 Depth of throat A and 250 300 300 510 385 S..mm. Depth of throat SD mm. 500 500 610 610 475 Travel... mm. 60 70 80 100 100 Working height...mm. 1.085 1.095 1.165 1.110 1.110 GENERAL SPECIFICATIONS No. strokes 20 mm. travel full cycle: A / S & SD 25/37 25/40 17/28 ---/31 ---/26 Motor power A / S and SD..KW 3/5 5/9 5/9 ---/15 ---/15 Gross weight approx. with production package: A Kg. 1.518 2.185 2.875 --- --- S SD...Kg. 1.598/2.012 2.323/2.760 3.162/7.795 5.980/7.245 6.785/8.050 Package dimensions: A and S mm. 1,67x1,16x2,09 1,92x1,20x2,05 2,13x1,20x2, 20 2,83x1,60x2,20 2,88x1,60x2,40 SD... mm. 2,10x1,16x2,09 2,31x1,20x2,05 2,69x1,40x2, 20 2,95x1,60x2,20 3,04x1,60x2,40 Volume of seaworthy 4,04 4,72 5,62 10 11,06 packing: A & S... m3 SD...m3 5,09 6,68 8,28 11,38 11,67 SPECIAL EQIPMENT-Press Brake Braking power...kn. 550 800 1100 1650 2200 Maximum width...mm. 500 600 700 700 700 Maximum capacity.mm. 500x3 300x10 600x3 350x10 700x3 400x10 700x3 400x12 700x3 400x12 TUBE NOTCHING Maximum diameter mm. 60 60 60 60 60
CHARACTERISTICS HYDRACROP MODELS IN INCHES 55/110 80/150 110/180 165/300 220/300 SHEAR FOR FLATS Flats... mm. 12 x 5/8 8 x 3/4 18 x 5/8 12 x3/4 24 x 5/8 16 x3/4 30 x3/4 20 x1 30 x3/4 20 x1 Length of blades...mm. 12 18 11/16 24 30 ½ 30 ½ Square bar... mm. 1 --- --- --- --- Working height... mm. 35 36 ½ 38 35 ½ 35 ½ Cutting an L-iron leg at 45º mm. 2 ½ 3 4 5 5 SHEAR FOR SECTION IRON Angle station... KN 120 165 200 320 330 L at Right Angleº(non deformation sys) mm. 4 x4 x1/2 5 x5 x1/2 6 x6 x1/2 8 x8 x3/4 8 x8 x3/4 L at 45º... mm. WITH SPECIAL BLADES 3 x3 x 5/16 3 x3 x 5/16 3 x3 x 5/16 3 x3 x 5/16 3 x3 x 5/16 L at 90º 5 x5 x1/2 6 x6 x1/2 6 x6 x5/8 8 x8 x1 8 x8 x1 BAR CROPPER Round bar Ø....mm. 1 9/6 1 ¾ 2 2 3/8 2 3/8 Square bar....mm. 1 9/6 1 ¾ 2 2 3/8 2 3/8 WITH SPECIAL BLADES Channels UPN....mm. 5 5 6 7 7 Beams IPN.....mm. 4 5 6 7 7 NOTCHER Sheet metal...mm. 3/8" 15/32 ½ 5/8 5/8 L Iron...mm. 4 4 4 5 5 Depth...mm. 3 1/2 3 1/2 3 1/2 4 5/16 4 5/16 Width...mm. 15/8 2 2 2 ¼ 2 ¼ PUNCHING TOOL Power. KN 60 88 120 185 240 Max. Capacity with quick change system... mm. 1 ½ in3/8 1 ½ in 9/16 1 ½ in ¾ 1 ½ in 1 ¼ 1 ½ in 1 ½ Depth of throat A and S..mm. 10 12 12 15 15 Depth of throat SD... mm. 20 20 24 24 - Travel... mm. 2 ¾ 2 3/8 3 5/32 3 15/16 3 15/16 Working height... mm. 42 3/4 43 15/16 45 1/8 43 45/64 43 45/64 GENERAL SPECIFICATIONS No. strokes ¾. travel full cycle: A S and SD. 25 37 25 40 17 28 31 26 Motor power A..HP S and SD..KW 6.5 6.5 6.5 12.5 6.5 12.5 -- 20 ---- 20 Net weight approx. with production package: A.....Kg. 2.900 4.180 5.500 -- --- S......Kg. 3.060 4.450 6.050 11.400 13.000 SD...Kg. 3.860 5.280 7.260 13.860 15.400 SPECIAL EQUIPMENTS Press Brake Braking power...kn. 60 88 120 185 240 Maximum width...mm. 19 23 27 27 27 Maximum capacity...mm. 19.69x1/4 23.62x1/4 27.56x1/4 27.56x1/4 27.56x1/4 TUBE NOTCHING Maximum diameter...mm. 4 6 6 6 6