PLANTER CHECKLIST Serial Number: Model: Inspection Date: Inspected By:
Refer to applicable Operator & Parts Manual for planter specific maintenance and parts information. HITCH & TONGUE Clevis.... wear Hitch...level during operation Safety Chain... correctly routed and attached Tongue Wear Pads...wear/adjustment Hardware... tight Parts Needed: DRIVES Wheel Modules....wear/lubrication Contact Drive Chains...wear/lubrication Sprockets...wear/alignment Idlers...tension/alignment Transmissions/shafts/chains...wear/lubrication Shear Pins... replenish Point Row Clutches... operation Contact Drive Tires...pressure Parts Needed: FRAME & TRANSPORT SYSTEMS Frame Welds/Structural Members.... cracks and failure Hardware... tight Hydraulic System...leaks and damage Wing and Transport Tires...pressure Wing Hinge and Pivot... wear and damage Row Markers Disc Blades... wear Bearings...wear/failure Stand...adjustment and pad wear Mounting Hardware... tight Operating Speed...verify and adjust Chain...tightness Transport System Safety Latch.... inspect operation/adjust Wheel Bearings...wear/failure Mud Scrapers...adjust Lug Nuts/Bolts and Spindle Bolts...torque Center Post Wear Pads...hardware/adjustment Cam Follower...adjustment Toolbar Height...0 to Lubrication...refer to manual Parts Needed: SAFETY Warning Lights.... operate correctly SMV Sign...visible and reflective Safety Warning Signs...condition/clean Reflectors/Reflective Decals...condition/clean Parts Needed: ELECTRICAL & SEED MONITOR Wiring Harnesses Routing.... secure as needed Cables and Connections... damage/corrosion Control Console Functions... verify operation Sensors (Electronic Seed Monitor) Magnetic/Radar Distance Sensors.. operation/damage Seed Tube Sensors... operation/damage Shaft Rotation Sensors... operation/damage Parts Needed: FERTILIZER EQUIPMENT Squeeze Pump Metering Hoses... fatigue Bushings and Rollers...condition Roller Plate and Springs...............condition Drive Chain...alignment/lubrication Piston Pump Case/Hose Connections.... condition Oil Level... check/replenish Drive Chain and Tires...condition/lubrication Hoppers, Tanks, and Delivery Hoses Hoppers.... condition/lubrication Tanks and Valves...condition Hoses...condition/attachment Drive Chain...alignment/lubrication Openers Bearings... wear/failure Disc Blade...wear Scrapers and Knives...condition/adjust Drop Tube...condition/adjust Parts Needed: Planter Checklist Rev. 0/6
ROW UNITS General Mounting Plate and U-bolts.... tight Parallel Arms/Bushings/Hardware...wear/damage Down Pressure Springs...missing/damage Row Unit Shank...condition Double Disc Openers Disc Blade... replace if 4½" or less Blade Contact...shim adjustment Bearings...wear/failure Parts Needed: Gauge Wheels Tires.... wear/damage Wheel Arms...wear/damage Wheel-to-Blade Contact...shim adjustment Bearings...wear/failure Depth Adjustment...inspect/adjust Lubrication...refer to manual No-Till Coulters/Attachments Depth.... align/adjust Disc Blade...replace if 4½" or less Bearings...wear/failure Residue Wheels and Bearings...condition Seed Hopper Hopper and Lid.... wear/damage Seed Hopper Latch...adjust Clutch...meter drive alignment/lubrication Chain Idler...tension/alignment Granular Chemical Hopper and Lid.... wear/damage Meter...roller/gate/bushings Clutch...alignment Chain...tension/alignment/lubrication Tubes and Banders...condition Closing Wheels Tires and Wheels.... wear/damage Hardware... tighten Bearings...wear/failure Springs...missing/damage Bushing and Eccentrics...alignment Parts Needed: SEED METERS Finger Pickup Meter Meter... clean Belt, Brush and Carrier Plate... wear Finger Assembly... rust/wear/damage Rolling Torque...should be 5 in/lbs Seed Baffle...wear/damage Brush-Type Seed Meter Meter... clean Brushes... frayed, damaged or missing bristles Seed Disc...wear Wear Band...groove/wear EdgeVac Vacuum Hoses............ Remove from meters and operate fan at full hydraulic flow for two minutes to clear system of debris. Vacuum Cover and Disc.... wear/damage Brushes... frayed, damaged or missing bristles Meter Housing and Disc... clean Analog Vacuum Gauge Breather... clean Vacuum Singulator.... clean and/or replace Vacuum Seal...wear/damage Seed Discs...clean/wear Debris Ejector... clean and/or replace Parts Needed: OTHER ATTACHMENTS Parts Needed: Rev. 0/6 Planter Checklist 3
Brush-Type Seed Meter 3 Used W/ Soybean And Cotton Discs 4 7 Used W/ Milo/Grain Sorghum Discs 5 ¾" 8 ⅜" 6 Finger Pickup Seed Meter 0 3 9 4 5 6 7 B 8 A 4 Planter Checklist Rev. 0/6
ITEM PART NO. QTY. DESCRIPTION GA808 Housing W/Bearing GA5698 Bearing GD8778 Wear Strip 3 GA5699 Upper Brush 4 GD Upper Brush Retainer (Used W/Soybean and Cotton Discs) 5 GA5834 Lower Brush 6 GA5794 Seed Disc, Soybean, 60 Cell, Black Color-Coded GA684 GA5796 GA668 GA6478 GA68 GA755 7 GD837 Seed Disc, Specialty Soybean, 48 Cell, Dark Blue Color-Coded Seed Disc, Cotton, Acid-Delinted, 30 Cell, White Color-Coded Seed Disc, Large Cotton, Acid-Delinted, 36 Cell, Tan Color-Coded Seed Disc, High-Rate Cotton, Acid-Delinted, 48 Cell, Light Green Color-Coded Seed Disc, Hill-Drop Cotton, Acid-Delinted, Cell, Brown Color-Coded Seed Disc, Small Hill-Drop Cotton, Acid-Delinted, Cell, Dark Green Color-Coded 8 GA598 Seed Disc, Small Milo/Grain Sorghum, 30 Cell, Red Color-Coded GA687 GA5795 GA6633 A 700-0079 Brush Meter ITEM PART NO. QTY. DESCRIPTION GD86 Seed Belt GA09 Bearing Seed Disc, Large Milo/Grain Sorghum, 30 Cell, Light Blue Color-Coded Seed Disc, High-Rate Small Milo/Grain Sorghum, 60 Cell, Red Color-Coded Seed Disc, High-Rate Large Milo/Grain Sorghum, 60 Cell, Yellow Color-Coded 3 GR569 Carrier Plate W/Brush and Screw (Corn) GR0664 GA00 Seed Disc #6 Upper Brush #3 Lower Brush #5 Carrier Plate W/Brush and Screw (Sunflower) Brush 4 GD8704 Finger, Corn 5 GD9790 Spring 6 GB040 Cam 7 GD58 Finger Holder 8 GD3 Seed Baffle 9 GD04 Idler Item Stainless Steel Wear Band # 0 GD04 Belt Drive Sprocket Brush Meter Life Expectancy GD9333 Finger, Oil Sunflower GD787 Half Rate Blank Finger Life Expectancy 00-00 acres per row 0-400 acres per row 40-800 acres per row 40-800 acres per row A GR848 Finger Assembly, Corn B GR54 Finger Assembly, Oil Sunflower C 700-0078 Corn Meter Brush #3 Carrier Plate #3 Fingers & Springs #4, #5 Drive Belt Sprocket, #0 Item Seed Belt #, Belt Housing & Belt Housing Cover Finger Pickup Meter Life Expectancy 00-00 acres per row 0-400 acres per row 40-800 acres per row 40-800 acres per row Life Expectancy Inspect for damage or cracks Rev. 0/6 Planter Checklist 5
EdgeVac Meter Used With 60 Cell Milo/Grain Sorghum Disc, 60 Cell Soybean Disc, 0 Cell High-Rate Soybean Disc And 39 Cell And 4 Cell Popcorn Discs 4 5 3 Vacuum Meter 4 6 3 5 6 Planter Checklist Rev. 0/6
ITEM PART NO. QTY. DESCRIPTION GA848 Singulator Brush GA935 Crowder Brush 3 GD708 Wall Brush/Vent 4 GD7049 Seed Disc, Corn/Popcorn, 39 Cell, Light Blue Color-Coded GD7048 GD4467 GD4468 GD7050 GD787 GD8095 GD786 GD8098 GD4477 GD4805 Seed Disc, Low-Rate Corn/Popcorn, 4 Cell, Light Green Color-Coded Seed Disc, Soybean, 60 Cell, Black Color-Coded Seed Disc, High-Rate Soybean, 0 Cell, Dark Blue Color-Coded Seed Disc, Milo/Grain Sorghum, 60 Cell, Yellow Color-Coded Seed Disc, Hill-Drop Cotton, Acid-Delinted, 3 Seeds Per Cell, 0 Cell, Brown Color-Coded Seed Disc, Small Hill-Drop Cotton, Acid-Delinted, 0 Cell (3 Seeds Per Cell), Grey Color-Coded Seed Disc, Cotton, Acid-Delinted/Small Dry Edible Bean, 54 Cell, Dark Green Color- Coded Seed Disc, Small Cotton/Sunflower, 54 Cell, White Color-Coded Seed Disc, Large Dry Edible Bean, 54 Cell, Tan Color-Coded Seed Disc, Sugar Beets, 80 Cell, Blue Color-Coded 5 GA9 Vacuum Cover W/Elbow And Cap GD7099 3 6" Hose Barb Elbow GD75 Cap Crowder Brush # Singulator Brush # Wall Brush #3 Item EdgeVac Meter Life Expectancy Life Expectancy 400 acres per row 400 acres per row 400 acres per row ITEM PART NO. QTY. DESCRIPTION GB0676 Lip Seal GA0879 Inner Blade Sub Assembly G693 Torx Flat Head Machine Screw, No. 4-40 x ½" GB09 GB0973 Lower Blade Lower Control 3 GA8775 Singulator Assembly 4 GB0780 Brush 5 GA0746 Brush Assembly 6 G9040X Seed Disc, Corn, 40 Cell, Light Blue Color-Coded, Ejector Wheel, and Spring G904X Seed Disc, Soybean, 0 Cell, Black Color-Coded, Ejector Wheel, and Spring G9043X G904X G97X G973X G9308X Seed Disc, Sugar Beets/Milo, Dark Orange Color-Coded, Ejector Wheel, and Spring Seed Disc, Sunflower, 40 Cell, Gray Color-Coded, Ejector Wheel, and Spring Seed Disc, Cotton, 60 Cell, Green Color-Coded, Ejector Wheel, and Spring A G977X Vacuum Meter Assembly, Pull Row Unit B G975X Vacuum Meter Assembly, Push Row Unit Singulator #3 Seed Disc #6 Seal # Ejector Item Seed Disc, Black Turtle and Navy Edible Bean and Popcorn, 60 Cell, Brown Color- Coded, Ejector Wheel, and Spring Seed Disc, Pinto and Great Northern Edible Beans and Low-Rate Soybean, 60 Cell, Dark Blue Color Coded, Ejector Wheel, and Spring Vacuum Meter Life Expectancy 600-900 acres per row 600-900 acres per row 600-900 acres per row 50-500 acres per row Life Expectancy Rev. 0/6 Planter Checklist 7
Note: Check for excessive wear. Torque to 30 ft-lbs 3000 Row Unit Series (Base Row Unit) 5 E Note: Check for wear by pulling from side to side on closing wheels. If there is excessive play, replace arm bushing. 0 7 B 4 9 8 6 3 4 5 6 7 8 9 0 3 4 5 ITEM A057 03 D59 A0L 035 06 038 D845 D07 004 047 D0473 A04 D306 B030 09 PART NUMBER WELD, SHANK (PAINTED) BUSHING, 5/8".047 X.688 X.03 PL SLEEVE, PLTD 5/8 OD X.385 X.78 SCRAPER, DISK (PAINTED) HHCS 3/8-6 X -3/4 GR5 CS PLT NUT-FLG SER 3/8-6 HDN CS PLT HHCS 3/8-6 X 5/8 GR5 CS PLT HUB CAP, PLASTIC 3 BOLT, OPNR BLADE 5/8- LH GR5 PLT BUSHING, X.656 X.09 HARD/BLK OX RIVET BUTTON HD /4 x / PLTD HOUSING, BEARING (RIBBED) PLTD BEARING, 5/8" DISC BLADE, 5" 3.5MM SCRAPER, PAINTED HSHCS 5/6-8 X GRU AS PLT DESCRIPTION JON HAZELETT IP7 D 4 Note: Replace inner scraper when worn to 5/8" or less. A 3 8 Planter Checklist 5 Note: ) Shim blades to have approximately " +/- /" contact. ) Replace blade at 4 /" or less. Rev. 0/6 6 QTY
6 7 8 0 9 F ITEM PART NO. QTY. DESCRIPTION G3303-98 Chain, No. 4, 98 Pitch Including Connector Link G3303-08 Chain, No. 4, 08 Pitch Including Connector Link G3303-6 Chain, No. 4, 6 Pitch Including Connector Link G3303-4 Chain, No. 4, 4 Pitch Including Connector Link G3303-4 Chain, No.4, 4 Pitch Including Connector Link GB08 Bushing, /3" I.D. x 7/8" O.D. x 9/3" Long 3 GD306 Disc Blade, 3.5 mm x 5" 4 GA0R GA0L Disc Scraper, R.H. Disc Scraper, L.H. 5 GB030 Seed Tube Guard/Inner Scraper 6 GD086 Tire 7 GA7975 Wheel Arm W/Grease Fitting, Bushings And Seals, L.H. GA7976 Wheel Arm W/Grease Fitting, Bushings And Seals, R.H. 8 GD085 Rubber Tire, " x " 9 GA67 Bearing 0 GB08 Stepped Bushing GB039 Eccentric Bushing GA597 Closing Wheel Arm 3 GA6597 Cast Iron Closing Wheel W/Bearing GA67 Bearing Note: Replace blades at 4 /" or less. ITEM PART NO. QTY. DESCRIPTION 6 GB0383 Bushing, ⅛" O.D. x 5/3" I.D. x 3/4" Long 7 GA8760 Weed Guard W/Spring Pin G0765 Spring Pin, ¼" x " 8 GA5654 Hub W/Bearings GA04 Bearing 9 GB0387 Wheel, Tine, 3/8" x " 0 GA8603 Bearing, Double Row GD7803 Disc Blade, Fluted,, 8 Flutes GA057 Shank W/Gauge Wheel Pivot Spindle And Set Screw A GA834 Disc Blade/Bearing Assembly, Less Dust Cap B GA7949 Gauge Wheel Complete C GK96 Gauge Wheel Arm Bushing And Seal Driver Kit, Includes: () Seal Driver, () Bushing Driver, () Instruction D GA6434 Rubber Closing Wheel Complete W/Bearing E GA0640 Meter Drive Assembly, /8 Tooth GA05 Meter Drive Assembly, /9 Tooth F GA35 Wheel Assembly, Tine, L.H. GA36 Wheel Assembly, Tine, R.H. G GK675 3K Row Unit Kit, Includes Items:, 4-5, and A 4 GD90 Nylon Half Wheel Note: Parallel arms from ground to bottom of toolbar = 0-" 5 GA037 Double Sprocket And Bearing, Drive Clutch, /9 Tooth GA43 Double Sprocket And Bearing, Drive Clutch, /8 Tooth Rev. 0/6 Planter Checklist 9
3000 Row Unit Series (Options) 3 B W/Residue Wheels 4 5 6 Ag Leader Electric Clutch (Pull Row) 4 5 A 7 9 0 6 Frame Mounted Coulter W/Residue Wheels Ag Leader Electric Clutch (Push Row) 8 9 6 7 4 0 5 8 3 Interplant Push Row Unit 0 Planter Checklist Granular Chemical Meter and Meter Drive Rev. 0/6
ITEM PART NO. QTY. DESCRIPTION G3303-34 Chain, No. 4, 34 Pitch Including Connector Link G3303-44 Chain, No. 4, 44 Pitch Including Connector Link GA05 Meter Drive Assembly, /9 Tooth 3 GD96 Idler 4 G3303-88 Chain, No. 4, 88 Pitch Including Connector Link G3303-03 Chain, No. 4, 03 Pitch Including Connector Link 5 GD97 Shaft 6 GD748 Feed Roller, Hex Bore 7 GB05 Bearing 8 GD758 Hex Bushing 9 G3303-78 Chain, No. 4, 78 Pitch Including Connector Link 0 G3303-4 Chain, No. 4, 4 Pitch Including Connector Link 4 GD7803 Disc Blade, Fluted, ", 8 Flutes GD7804 Disc Blade, Bubbled, GD954 5 GB09 Coulter Hub Disc Blade, Fluted, ¾", 3 Flutes 6 GA8603 Bearing, Double Row 7 GB0387 Wheel, Tine, 3/8" x " GA5654 GA04 Hub W/Bearings Bearing 8 GD96 Idler 9 G3303-96 Chain, No. 4, 96 Pitch Including Connector Link 0 GB030 Seed Tube Guard/Inner Scraper GB08 Bushing, /3" I.D. x 7/8" O.D. x 9/3" Long GA5787 Lower Arm 3 GA70 Bearing/Sprocket, 7/8" Hex Bore 4 GA969 Upper Arm 5 GD96 Idler 6 GA05 Meter Drive Assembly, /9 Tooth GA0640 Meter Drive Assembly, /8 Tooth A GA36 Wheel Assembly, Tine, R.H. GA35 Wheel Assembly, Tine, L.H. B GA864 Hub W/Bearing And Retaining Ring Rev. 0/6 Planter Checklist
4000 Row Unit Series Note: Check for excessive wear. Torque to 30 ft-lbs 3 A Note: Replace inner scraper when worn to 5/8" or less. 8 5 9 0 4 3 Note: Check for wear by pulling from side to side on closing wheels. If there is excessive play, replace arm bushing. Note: ) Shim blades to have approximately " +/- /" contact. ) Replace blade at 4 /" or less. 9 Note: Replace blades at 4 /" or less. B 0 8 5 7 6 6 C E Planter Checklist Rev. 0/6
4 Without Electric Clutch 3 6 4 5 D 7 ITEM PART NO. QTY. DESCRIPTION GB08 Bushing, /3" I.D. x ⅞" O.D. x 9/3" Long GD5069 Lower Parallel Arm 3 GD5070 Upper Parallel Arm 4 GA8004 Row Unit Idler W/Out Electric Clutch 5 G3303-45 Chain, No. 4 Roller Chain, 45 Pitches, Vacuum G3303-35 Chain, No. 4 Roller Chain, 35 Pitches, Mechanical 6 GA0640 Meter Drive Assembly, /8 Tooth, Vacuum GA05 Meter Drive Assembly, /9 Tooth, Mechanical 7 GD96 Idler 8 GB0504 Scraper 9 GD306 Disc Blade, 3.5 mm x 5" 0 GA04 Bearing GD0473 Bearing Housing GA5450 R.H. Disc Scraper GA545 3 GA67 Bearing 4 GD086 Tire L.H. Disc Scraper 5 GA7975 Wheel Arm W/Grease Fitting, Bushings And Seals, L.H. GA7976 Wheel Arm W/Grease Fitting, Bushings And Seals, R.H. 6 GD90 Nylon Half Wheel 7 GD085 Rubber Tire, " x " 8 GA67 Bearing 9 GA6597 Cast Iron Closing Wheel W/Bearing GA67 Bearing ITEM PART NO. QTY. DESCRIPTION 0 GB08 Stepped Bushing GB039 Eccentric Bushing GA45 Cam 3 GA5654 Hub W/Bearings GA04 Bearing 4 GB0387 Wheel, Tine, ⅜" x " 5 GD7803 Disc Blade, Fluted, ", 8 Flutes (shown) GD7804 Disc Blade, Bubbled, " GD954 Disc Blade, Fluted, ¾", 3 Flutes 6 GA864 Hub W/Bearing and Retaining Ring GA8603 Bearing, Double Row A GA834 Disc Blade/Bearing Assembly, Less Dust Cap B GA6333 Gauge Wheel Complete C GA6434 Rubber Closing Wheel Complete W/Bearing D GA35 L.H. Residue Wheel GA36 R.H. Residue Wheel E GA864 Hub W/Bearing and Retaining Ring Note: Parallel arms from ground to bottom of toolbar = -4" Rev. 0/6 Planter Checklist 3
4000 Row Unit Series 3 B 4 3 5 4 6 B Row Unit Mounted Double Residue Wheels Row Unit Mounted Single Residue Wheels 7 C C 9 8 C C D D D Granular Chemical Meter and Meter Drive 4 Planter Checklist Rev. 0/6
ITEM PART NO. QTY. DESCRIPTION GD758 Hex Bushing G3303-08 Chain, No. 4, 08 Pitch Including Connector Link (Vacuum) G3303-4 Chain, No. 4, 4 Pitch Including Connector Link (Mechanical) GR096 Connector Link, No. 4 3 GA04 Bearing 4 GA5654 Hub W/Bearings (Includes Item 3) 5 GB0387 Wheel, Tine, ⅜" x " 6 GB0387 Wheel, Tine, ⅜" x " 7 GD748 Feed Roller, Hex Bore 8 GB05 Bearing 9 GD97 Shaft A GA864 Hub W/Bearing and Retaining Ring B GA35 L.H. Residue Wheel GA36 R.H. Residue Wheel Rev. 0/6 Planter Checklist 5
NOTES 6 Planter Checklist Rev. 0/6
Frequently Asked Questions Q: What are the recommended Lubrication requirements? A: Standard Hoppers Graphite Teaspoon per hopper fill Make a thick line around the outer edge of the hopper each time you fill Error to the heavy side Talc Use ONLY for seed that has a tacky treatment (seed that stays in that shape when you place your hand in the hopper and make a ball) / Cup per hopper fill or enough to fully coat the seed Must be mixed into the seed Bulk Fill Graphite to One pound bottles per hopper, per 50 units of seed Error to the heavy side Talc Use ONLY for seed that has a tacky treatment (seed that stays in that shape when you place your hand in the hopper and make a ball) Mix talc in as you load the seed in order to equally distribute it Q: How do I change my meter settings on my KPM III when switching crops? A:. With display powered on, in planting screen, Press the bottom function button (F6) times. Rotate Black Knob to highlight (. Setup Mode) 3. Press the Black Knob 4. Rotate Black Knob to highlight (. Seed Meter Settings) 5. Rotate Black Knob to highlight Crop Type 6. Press the Black Knob 7. Rotate Black Knob to select crop switching to 8. Press the Black Knob 9. Rotate Black Knob to select OK 0. Press the Black Knob. Press the nd function button (F) to return to the planting screen Note: If planter is set up with Interplant be sure and Enable or Disable the Interplant for the appropriate crop selected:. From the planting screen, Press the bottom function button (F6) times. Rotate Black Knob to select 3. Enable Interplant or Disable Interplant 3. Press the Black Knob to toggle Interplant on or off 4. Verify Interplant is Enabled or Disabled by text at the bottom of the screen Effective Row Spacing: 30.00 or Effective Row Spacing: 5.00 Q: What are the recommended Bulk Fill settings for each crop? A: Corn - 4 Soybeans 0-7 Planter Checklist Rev. 0/6
Q: How do I adjust my seed tube sensitivity? A: Seed tubes will automatically change to factory settings: Corn - 5; Soybeans - 0. Do not adjust sensitivity until you have performed an in-field check. Adjustments are made through the display/monitor. The lower the sensitivity number, the more sensitive the seed sensors are. KPM III. With display powered on, in planting screen, Press the bottom function button (F6) times. Rotate Black Knob to highlight (. Setup Mode) 3. Press the Black Knob 4. Rotate Black Knob to highlight (. Seed Meter Settings) 5. Rotate Black Knob to highlight Crop Type 6. Press the Black Knob 7. Enter the number (the smaller the number, the greater the sensitivity), pressing the Black Knob after each digit 8. Press the Enter Button 9. Press the nd function button (F) to return to the planting screen Integra. From the Home screen, press the Wrench Icon. Highlight the Configuration you are using 3. Press the Wrench Icon in the center of the screen 4. Press Seed Monitor in the lower center part of the screen 5. Press Planter Configuration. Sensitivity is found in the lower left of the screen 6. Make adjustments accordingly (the smaller the number, the greater the sensitivity) 7. Press the Green Check 8. Press the Green Check again 9. Press the Back Arrow 3 times to return to the Home Screen ISOBUS Note: steps/screens will vary depending upon the display being used (John Deere, Case, etc.). From the Kinze Home screen (Page ), press the Settings icon. Press the Arrow to the left of Seed Sensor Sensitivity 3. Select the crop type that you want to change the sensitivity for 4. Using the number pad, change the sensitivity The smaller the number, the greater the sensitivity The sensitivity will save for each crop type you change The sensitivity will change for each crop type automatically when you select the other crop 5. Press Accept 6. Press Done 7. Press the Previous button to go back to the main planting screen Q: How do I replace a seed tube sensor? A: KPM III. With display powered on, in planting screen, Press the bottom function button (F6) times. Rotate Black Knob to highlight (. Setup Mode) 3. Press the Black Knob 4. Rotate Black Knob to highlight (9. Sensor Set-Up) 5. Press the Black Knob 6. Select the row you are going to replace 7. Press the Remove button (F Function Button) 8. Remove the old sensor and install the new one 9. Press Install; monitor will beep once installation is complete 0. Press Done 8 Planter Checklist Rev. 0/6
Integra. From the HOME SCREEN, press the Wrench icon. Select a Configuration on the list 3. Press the Wrench button in the middle of the screen 4. Press the Seed Monitor button in the bottom center of the screen 5. Press the Sensor Configuration button 6. Highlight the sensor you want to replace 7. Press Remove next to the sensor you wish to remove 8. Physically remove the old sensor 9. Install the new sensor on the planter 0. Plug the new sensor into harness. Press Install next to the sensor that was replaced. Sensor should say OK. The monitor will beep once the installation is complete.. Press the Green Check 3. Press the Back Arrow 3 times to return to the HOME SCREEN ISOBUS. From the Planter Home Page (Page ), press the Settings icon. Press the arrow to the left of Mux-Bus 3. Press the center box and select the sensor you wish to change 4. Press remove on the right hand side of the screen 5. Unplug old sensor and install new seed tube sensor plugging it into the main seed tube harness 6. Press add on the display. The monitor should double beep and the Status should read OK. 7. Press the previous button in the lower left twice to get back to the settings screen Q: How do I find my crop population? A: ESTIMATING CROP POPULATION ROW WIDTH How many plants per acre? STEP : Measure /000 of acre (see above) STEP : Count plants STEP 3: Multiply by 000 Example: 30" rows - measure 7' 5" Counted 7 plants Multiply by 000 LENGTH OF ROW FOR /000 ACRE 30 inches 7 feet, 5 inches inches 3 feet, 8 inches 0 inches 6 feet, inches 5 inches 34 feet, 0 inches 7,000 plants per acre ROWS PER ACRE Row Length Row Width (Inches) (Feet) 5 0 30 36 38 500 70 5 48 35 9 8 600 58 44 40 9 4 3 700 50 37 34 5 0 800 44 33 30 8 7 900 39 9 6 9 6 5,000 35 6 4 7 5 4,00 3 4 6 3 3,00 9 0 5,300 7 0 8 3,400 5 9 7 0 0,500 3 7 6 0 9,600 6 5 9 9,700 0 5 4 0 9 8,800 9 5 3 0 8 8,900 8 4 3 9 8 7,000 7 3 9 7 7,00 7 8 7 7,00 6 8 7 6,300 5 0 8 6 6,400 5 0 7 6 6,500 4 0 0 7 6 6,600 3 0 9 7 6 5,700 3 0 9 6 5 5 Example: 30 inch rows,,000 feet in length, equals 7 rows per acre. 9 Planter Checklist Rev. 0/6
NOTES Your Authorized Kinze Dealer www.kinze.com DEALER IMPRINT 0 Planter Checklist Rev. 0/6