HWH PARTS MANUAL SUB TABLE of CONTENTS TOOLS & CONNECTORS (Filename: MR75.DOC) (Revised: 19MAY17) ML11428-75 (Click to View Entire Section PDF File No Links MR75-75Z) > Electrical Tools & Connectors > Hydraulic Gauges & Isolation Kits > Hose Tools (& Hose Information) > Slide-Out Mechanism Tools > Slide-Out Accessory Tools - Environmental Air Seals > Valve Tools C:\0_Web\mr(pm)\MR75\mr75.doc Revised: 19MAY17 Page 1 of 2
ELECTRICAL TOOLS & CONNECTORS HYDRAULIC GAUGES & ISOLATION KITS HOSE TOOLS & HOSE INFORMATION SLIDE-OUT MECHANISM TOOLS SLIDE-OUT ACCESSORY TOOLS VALVE TOOLS Test Pigtails Multi-Purpose Voltage & Ground Test Pigtail - TS39641 Multi-Purpose Switch Test Pigtail - TS39643 One-Wire Indicator Switch Test Pigtail - TS39644 12V Test Light w/2-pin Black Packard Connector - TS39640 Test Pigtails Electronic Sensing Unit Test Pigtail - TS44002 Sensing Unit Ground Jumper - One Wire - TS51233 Crimper - TS46742 Stripper - TS46743 AMP MTA Connector Tools & MTA Connectors Crimp-Style MTA Housings AMP UML Tools & UML Connectors Weatherpack Packard Tools & Packard Connectors Deutsch Tools & Connectors Hydraulic Pressure Gauge Kit - TS7557 Test Kit for Room Creep - TS42926 Hydraulic Hose Adapter -4/-5 - TS57772 Hand Swaging Tools Hose Cutting Tools/Blades Dies & Pushers See Also "Hose Install & Service Information" Slide-Out Spanner Wrench for Adjusting Various Slide-Out Mechanisms - TS19138 Snap Ring Replacement Tool for "Train-Drive" Slide-Out Link Assemblies - TS27333 Environmental Air Seal Install Tool - TS48976 Environmental Double-Wiper Seal Install Tool - TS39526 Hydraulic Solenoid Valve Removal/Install Tool for 1.5" Valves with Nut Release - TS28238 Hydraulic Solenoid Valve Removal/Install Tool for 1.5" Valves with Flipper/Cam Release - TS42632 Hydraulic Solenoid Valve Spring Tool for Large & Small Valves - TS56317 Click to Link MR75.1110.PDF MR75.1111.PDF MR75.1199.PDF MR75.1200.PDF MR75.1202.PDF MR75.1300.PDF MR75.1400.PDF MR75.1500.PDF Click to Link MR75.1100.PDF MR75.1100.PDF MR75.1100.PDF Click to Link MR75.1000.PDF ml44100b1_hose.html Click to Link mr751100_so.html mr751100_so.html Click to Link MR75.1101.PDF MR75.1101.PDF Click to Link mr751100_vlv.html mr751100_vlv.html mr751100_vlv.html C:\0_Web\mr(pm)\MR75\mr75.doc Revised: 19MAY17 Page 2 of 2
HWH PARTS MANUAL TOOLS for SLIDE-OUTS (Filename: MR751100_SO.DOC Revised: 26MAY17) TOOLS for HYDRAULIC SLIDE-OUT MECHANISMS SPANNER WRENCH TS19138 (M101226) ORDER Used for various adjustments on multiple hydraulic slide-out mechanisms. SNAP RING ASSY TOOL TS27333 (TS22912 & TS22913) ORDER INSTRUCTION SHEET MI15.400C Used for snap ring replacement on HWH Train Drive Slide-Outs. ROOM EXTENSION USO PIN ALIGN TOOL TS57787 ORDER Used for aligning the pin between the chain and USO Mechanism on HWH USO Room Slide-Outs. LINK TO: HWH Install/Service Information LINK TO: HWH Parts Manual - "TOOLS" - Sub Table of Contents C:\TEMP\mr751100_so.doc 26MAY17 Page 1 of 1
HWH PARTS MANUAL TOOLS for VALVES (Filename: MR751100_VLV.DOC Revised: 16MAR16) TOOLS for HYDRAULIC SOLENOID VALVES HYDRAULIC SOLENOID VALVE CAP WRENCH TS28238 (AP27666) ORDER Used to remove and install small (1.5 Diameter) Nut Release style hydraulic solenoid valves. HYDRAULIC SOLENOID VALVE CAP WRENCH TS42632 (T42632) ORDER Used to remove and install small (1.5 diameter) Flipper/Cam Release style hydraulic solenoid valves. VALVE SPRING TOOL TS56317 (T31628) ORDER Used to install springs on needles on small (1.5 diameter) and large (2.25 diameter) hydraulic solenoid valves. LINK TO: HWH Install/Service Information LINK TO: HWH Repair Parts Manual Valve Section LINK TO: HWH Parts Manual - "TOOLS" - Sub Table of Contents C:\1_Parts_Manual\mr\mr751100_vlv.doc 16MAR16 Page 1 of 1
SWAGING EQUIPMENT FOR HWH HYDRAULIC HOSE HOSE CUTTER AND BLADE REPLACEMENT A swaging tool and the appropriate die and pusher is required to make hose assemblies. HWH PART # DESCRIPTION TS44701 (SHOWN) HAND SWAGING TOOL A square and clean hose cut is required to make hose assemblies. HWH PART # DESCRIPTION TS27788 HOSE CUTTING TOOL TS52678 DOES NOT INCLUDE DIE AND PUSHER. HAND SWAGING TOOL Has spring wire keepers instead of dogs to hold the die in place. TS27789 BLADE REPLACEMENT HWH Part Number TS00000 HWH Part Number PUSHER Refer to ML24976 for further swaging information. TS13676 - For 1/8" Parker Hose Ends TS52707 - For 3/16" Hose Ends TS52707 - For 1/4" Hose Ends HWH Part Number Key Pin Key Pin Receptacle PUSHER DIE DIE SETS Refer to ML24976 for further swaging information. TS44677 - For 1/8" Parker Hose Ends TS51677 - For 3/16" Hose Ends TS44675 - For 1/4" Hose Ends IMPORTANT: Die sets will have matching serial numbers. Serial numbers on the die bottoms must match. DO NOT use dies with non matching numbers. NOTE: Swaging tools, pushers and dies must be marked with HWH Part Numbers. DO NOT use unmarked parts. MR75.1000 23JUL14
GAUGES TS7557 (AP7557) HYDRAULIC PRESSURE GAUGE KIT 5000 P.S.I. MR75.1100 17MAR16
TS48976 AIR SEAL INSTALLATION TOOLS TS39526 ENVIRONMENTAL DOUBLE WIPER SEAL INSTALLATION TOOL MR75.1101 29MAR12
TEST PIGTAILS NOTE: TS39670 KIT CONTAINS ALL PARTS LISTED BELOW. TS39641: MULTI-PURPOSE VOLTAGE AND GROUND TEST PIGTAIL. USED TO CHECK IN-USE VOLTAGE SUPPLY FOR SOLENOID VALVES - HYDRAULIC OR AIR. THIS PIGTAIL PLUGS IN BETWEEN THE HARNESS PLUG AND THE VALVE. THIS PIGTAIL CAN BE USED WHEN TESTING TWO WIRE WARNING SWITCHES, LIMIT SWITCHES. AND PRESSURE SWITCHES WITH TWO PIN BLACK PACKARD CONNECTORS. 12.00" B A B A B A 6.00" TS39643: MULTI PURPOSE SWITCH TEST PIGTAIL. THIS PIGTAIL IS USED TO SIMULATE ANY TWO WIRE WARNING SWITCH, PRESSURE SWITCH, OR LIMIT SWITCH WITH A TWO PIN GRAY OR BLACK PACKARD CONNECTOR. THE PIGTAIL PLUGS INTO THE HARNESS INSTEAD OF THE SWITCH BEING TESTED. 30.00" TS39644: INDICATOR SWITCH TEST PIGTAIL - ONE WIRE. THIS PIGTAIL IS USED TO SIMULATE ANY ONE WIRE INDICATOR SWITCH SUCH AS A JACK OR MANIFOLD PRESSURE SWITCH WITH A SINGLE PIN PACKARD CONNECTOR. THIS PIGTAIL PLUGS INTO THE APPROPRIATE HARNESS INSTEAD OF THE SWITCH BEING TESTED. 30.00" TS39640: 12 VOLT TEST LIGHT WITH 2 PIN BLACK PACKARD CONNECTOR B A 6.00" MR75.1110 06DEC06
TEST PIGTAILS TS44002: SENSING UNIT TEST PIGTAIL. USED TO ISOLATE A ELECTRONIC SENSING UNIT FROM A SYSTEM. THIS PIGTAIL CAN BE USED TO EMULATE FRONT, REAR, RIGHT, AND LEFT SENSE. IT ALSO INCLUDES A LIGHT THAT ILLUMINATES WHEN THERE IS +12V. FRONT REAR LEFT SIDE RIGHT SIDE 18.00" TS51233: SENSING UNIT GROUND JUMPER - ONE WIRE. THIS PIGTAIL IS USED TO GROUND THE ELECTRONIC SENSING UNIT SENSITIVITY PIN. 48.00" MR75.1111 01NOV12
PURCHASED TOOLS TS46742 CRIMPERS - THOMAS & BETTS WT111M TY-RAP AB C STA-KON LUG A 22 TO 18 B 16 TO 14 C 12 TO 10 WT-111M MADE IN USA TS46743 STRIPPERS - IDEAL INDUSTRIES INC. 45-092 MR75.1199 14MAY10
MTA TOOLS AND CONNECTORS AMP AMP TS7380 CONNECTION HEADER ONLY ( AMP #58082-1) TS7379 PISTOL GRIP ONLY AUTOMATIC INDEXING (AMP #58074-1) TS5054 TEE HANDLE USED TO INSERT WIRES 1 AT AT TIME (AMP #59804-1) MTA CONNECTOR PART NO. RT NO. CONSIST OF FOLLOWING RT520203 RT520403 RT520503 2-CIRCUIT 2-CIRCUIT 4-CIRCUIT 4-CIRCUIT 5-CIRCUIT 5-CIRCUIT RT520603 RT520703 RT520903 RT521003 RT521103 RT521203 6-CIRCUIT 6-CIRCUIT 7-CIRCUIT 7-CIRCUIT 9-CIRCUIT 9-CIRCUIT 10-CIRCUIT 10-CIRCUIT 11-CIRCUIT 11-CIRCUIT 12-CIRCUIT 12-CIRCUIT MR75.1200 22MAY02
CRIMP MTA TOOLS AND CONNECTORS CONTACT HWH CORPORATION BEFORE ORDERING HOUSINGS OR SOCKETS PART NUMBER AND DESCRIPTION RT90929 4-CIRCUIT RT90930 5-CIRCUIT RT90931 6-CIRCUIT RT90932 7-CIRCUIT RT90933 9-CIRCUIT RT90934 11-CIRCUIT CRIMP STYLE MTA HOUSINGS (SOLD IN BAGS OF 5) SOCKET KEY PIN RT90935 (CONTAINS 20 SOCKETS AND 5 KEY PINS) MR75.1202 28SEP11
UML TOOLS AND CONNECTORS CONTACT HWH CORPORATION BEFORE ORDERING HOUSINGS, SOCKETS, OR PINS 458994-1 TS5057 CONTACT EXTRACTION TOOL (AMP #458994-1) RT500201 RT500301 RT500401 RT500601 RT500901 PART NO. 2-CIRCUIT 3-CIRCUIT 4-CIRCUIT 6-CIRCUIT 9-CIRCUIT DESCRIPTION UNIVERSAL MATE-N-LOK PLUGS (SOLD IN BAGS OF 5) RT500202 RT500302 RT500402 RT500602 RT500902 PART NO. 2-CIRCUIT 3-CIRCUIT 4-CIRCUIT 6-CIRCUIT 9-CIRCUIT DESCRIPTION UNIVERSAL MATE-N-LOK PLUGS (SOLD IN BAGS OF 5) RT500122 SOCKET (SOLD IN BAGS OF 20) RT500111 PIN (SOLD IN BAGS OF 20) MR75.1300 28SEP11
PACKARD TOOLS AND CONNECTORS 14-16 18-20 TS5055 TOOL TERMINAL PACKARD (WEATHER PACK #12014254) TS5056 TOOL TERMINAL REMOVAL PARKARD (WEATHERPACK #12014012) TOWER CONNECTORS AND SEAL ASSEMBLIES (SOLD IN BAGS OF 5) C B A B A B A PART NO. RT510102 RT510202 (BLACK) RT90921 (GRAY) RT510302 DESCRIPTION 1-WAY TOWER 2-WAY TOWER 2-WAY TOWER 3-WAY TOWER RT510020 FEMALE SLEEVE: USED IN TOWER ASSEMBLIES (SOLD IN BAGS OF 20) SHROUD CONNECTORS (SOLD IN BAGS OF 5) B A B A C B A PART NO. RT510101 RT510201 (BLACK) RT90922 (GRAY) RT510301 DESCRIPTION 1-WAY SHROUD 2-WAY SHROUD 2-WAY SHROUD 3-WAY SHROUD RT510010 MALE PIN: USED IN SHROUD (SOLD IN BAGS OF 20) RT510030 CABLE SEAL: (SOLD IN BAGS OF 20) (ONE REQ D FOR EACH PIN OR SLEEVE) MR75.1400 22MAY02
12 S SPECIAL TOOLS DEUTSCH TOOLS AND CONNECTORS TS22762 - TOOL TERMINAL CRIMP DEUTSCH SEL. NO. 14 R A I 16 7 8 6 18 5 S E 20 4 T O 22 3 2 25 1 EL. NO. ROT 26 W IR E S A T E I Z E TS22757 - TOOL TERMINAL/WEDGE REMOVAL DEUTSCH PIN NOTE: PINS ARE SIZED TO WIRE GAUGE - SHIPPED IN QUANTITIES OF FIVE. SLEEVE NOTE: SLEEVES ARE SIZED TO WIRE GAUGE - SHIPPED IN QUANTITIES OF FIVE. 12-14 GAUGE 14 GAUGE 16-18 GAUGE RT91141 RT91144 RT91147 12-14 GAUGE 14 GAUGE 16-18 GAUGE RT91140 RT91142 RT91145 RECEIVER PLUG WEDGE WEDGE SEAL NOTE: WEDGE WILL BE SHIPPED WITH RECEIVER WHEN ORDERED - QUANTITY 1EA. NOTE: WEDGE AND SEAL WILL BE SHIPPED WITH PLUG WHEN ORDERED - QUANTITY 1EA. 4 PIN - GRAY LARGE RT91151 4 PIN - GRAY LARGE RT91149 6 PIN - GRAY RT91154 8 PIN - GRAY RT91156 8 PIN - BLACK RT91158 12 PIN - GRAY RT91161 12 PIN - GREEN RT91165 12 PIN - BROWN RT91167 4 PIN - GRAY 6 PIN - GRAY 8 PIN - GRAY 8 PIN - BLACK 8 PIN - GREEN 12 PIN - GRAY 12 PIN - BLACK 12 PIN - GREEN 12 PIN - BROWN RT91148 RT91152 RT91155 RT91157 RT91159 RT91160 RT91162 RT91163 RT91166 NOTE: RT91139 KIT CONTAINS 10 EACH OF T570012 CAVITY SEAL AND T570014 KEY PIN CAVITY SEAL USED TO PLUG EMPTY WIRE LOCATIONS KEY PIN USED TO PREVENT MISMATCHING SAME COLORED PLUGS TO SAME COLORED RECEIVERS MR75.1500 01FEB12