High Speed Hydraulic Motors Catalog HY13-20-0-001/NA zm16 zm17 223
Introduction High Speed Features High Starting Torque typically 90% of running torque. Smooth Output Torque throughout the entire speed range of the motor. High Speed Capabilities up to 70 rpm on some models. BiDirectional Operation built in checks internally relieve high pressure from the shaft seal. High Pressure Shaft Seal allows back pressure to without the requirement of Case Drain. Standard SAE Mounting 2 or 4 bolt mounting flanges, shaft and port dimensions conform to SAE standards. Long Life & Quiet Operation Precision Gerotor Design results in a motor with extended operating life and noise levels below most other hydraulic motors. Heavy Duty Bearings capable of withstanding radial and thrust loads. 224
Ordering Information High Speed XX X XX XX S XX N X Motor SAE Port & Product Port Port Shaft Drain Shaft Series Mounting/ Code Size Type Style Seal Valve Mount Series Code Type M2 SAE 1 (B-Frame) M4 SAE 82 (A-Frame) SAE Port & Mounting Code Ports Mtg. B Side 2-Bolt D Side 4-Bolt M4 not available. Port Size Series Code SAE M4 12 12 M2 12 12 16 16 Port Type Code Type S SAE Straight Thread Shaft Style Code Type Long, Single-End Short, Single-End Spine, Single-End Drain Code Type N Internal Includes plugged external drain. Shaft Seal Code Type B Nitrile V Fluorocarbon M4 only available with code shaft. Product Code Series Code Theoretical Displacement cm 3 /rev in 3 /rev 015 2.45.15 0 4.91. M4 045 7.37.45 0 9.83. 075 12.29.75 085 13.9.85 127.8 1.27 M2 169 27.7 1.69 254 41.6 2.54 339 55.6 3.39 8 83.2 5.08 THERMAL SHOCK WARNING: IF THE MOTOR IS TO OPERATED BY FLUID WHICH IS F OR MORE ABOVE THE OPERATING ENVIRONMENT TEMPERATURE, CONSULT FACTORY. 225
Introduction High Speed Applications Parker motors serve our customers worldwide in many industries and in many applications. Typical applications include: Starting and running torque comparison between Parker Gerotor and typical Spur Gear and Vane Motors. Fan Drives Swing Drives Vibratory Drives Wheel Drives Winch Drives High speed capabilities means increased cooling capacity. Rugged bearing design allows the fan to be mounted directly on the motor shaft. High starting torque and smooth output torque throughout the motor s speed range means optimum control. Rugged design, high speed capabilities, and optional cross port relief valve means maximum life for vibratory drives. High speed capabilities and high starting torque means faster road speeds and increased productivity. Smooth output torque throughout the speed range, high speed capabilities, and high starting torque means increased control, greater productivity. 226
M4 Series Performance Data & Mounting Data (Lbs. In.) M4-015 6 5 4 3 2 (GPM) (Lbs. In.) 1 125 M4-0 7 6 5 4 3 2 (GPM) 1 25 1 (Lbs. In.) 0 70 0 2 0 1 M4-0 12 8 6 4 (GPM) (Lbs. In.) 3 0 2 0 1 00 M4-075 14 12 8 6 4 (GPM) 2 2 00 37 00 Displacement cm 3 /rev (in 3 /rev) 015 Unit 2.45 (.15) 0 Unit 4.91 (.) 045 Unit 7.37 (.45) 0 Unit 9.83 (.) 075 Unit 12.29 (.75) Weight 015 Unit 7.3 Kg (16 lb) 0 Unit 7.7 Kg (17 lb) 045 Unit 8.2 Kg (18 lb) 0 Unit 8.6 Kg (19 lb) 075 Unit 9.1 Kg ( lb) Speed Recommended Range 015 Unit 75 to 70 rpm 0 Unit to 00 rpm 045 Unit to 00 rpm 0 Unit 36 to rpm 075 Unit to 00 rpm Minimum speeds indicated are based on constant load. For speeds outside of the recommended range, consult the factory. 227 Performance Curves: Data based on: Oil: 65 cst (0 SSU) Mobil DTE-26 Temp: 38 C ( F) Pressure Continuous: Intermittent, Max: 2 Transient, Max: Intermittent conditions are to be less than % of each minute. Transient conditions are to be less than 1% of every minute.
M4 Series Performance Data & Mounting Data M4-045 0 12 Dimensions are shown in millimeters. Dimensions within ( ) are in inches. (Lbs. In.) 2 0 1 8 6 4 (GPM) Code A B 015 143.26 (5.64) 7.44 (4.23) 0 149.61 (5.89) 113.79 (4.48) 045 156.21 (6.15) 1.14 (4.73) 0 162.31 (6.39) 126.49 (4.98) 075 168.66 (6.64) 132.84 (5.23) 2 00 MOUNTING DATA 228
M2 Series Performance Data 48 0 0 0 M2-085 15 5 70 68 0 0 0 0 0 M2-127 25 15 5 00 00 1 1 1 35 0 25 0 0 15 0 M2-254 1 1 1 1 1 10 35 0 25 0 0 15 M2-339 0 1 1 0 5 0 5 0 0 0 10 229
M2 Series Performance Data 70 7 625 0 375 2 125 M2-169 1 25 15 5 Displacement cm 3 /rev (in 3 /rev) 085 Unit 13.9 (0.85) 127 Unit.8 (1.27) 169 Unit 27.7 (1.69) 254 Unit 41.6 (2.54) 339 Unit 55.6 (3.39) 8 Unit 83.2 (5.08) Pressure Continuous: M2-8 All other Units Intermittent, Max: M2-8 PSI All other Units 2 Transient, Max: M2-8 170 All other Units 0 0 Intermittent conditions are to be less than % of each minute. Transient conditions are to be less than 1% of every minute. 0 175 1 125 75 25 17 35 10 12 25 0 7 15 0 2 5 0 10 M2-8 1 1 1 1 2 Speed Recommended Range 085 Unit to 00 rpm 127 Unit to 00 rpm 169 Unit 36 to rpm 254 Unit to 00 rpm 339 Unit to 00 rpm 8 Unit 15 to 10 rpm Minimum speeds indicated are based on constant load. For speeds outside of the recommended range, consult the factory. Weight 085 Unit 15.4 Kg (34 lb) 127 Unit 16.3 Kg (36 lb) 169 Unit 17.2 Kg (38 lb) 254 Unit 18.6 Kg (41 lb) 339 Unit.4 Kg (45 lb) 8 Unit 24.0 Kg (52 lb) Performance Curves: Data based on: Oil: 65 cst (0 SSU) Mobil DTE-26 Temp: 38 C ( F) * Stall torque band is application dependent, consult factory.
M2 Series Mounting Data Dimensions are shown in millimeters. Dimensions within ( ) are in inches. FLANGE OPTION SAE 1-4 Mounting Code Dimension A 085 158.8 (6.25) 127 165.1 (6.) 169 171.5 (6.75) 254 184.2 (7.25) 339 196.9 (7.75) 8 222.3 (8.75) DIMENSIONS PORT LOCATION DRAIN PORT 1. The shaft will rotate in the direction of this ARROWHEAD when Port A is the inlet IN or pressure port. 2. With Port B as the inlet IN or pressure port, the shaft will rotate in the direction of this ARROWHEAD. Drain Port Will Be: 1. No. 6-SAE for the SAE ported motors. 231
M2 Series Mounting Data SHAFT OPTIONS 232
Operating Pressures Continuous: M2-8 All other Units Intermittent, Max: M2-8 PSI All other Units 2 Transient, Max: M2-8 170 All other Units Filtration 25 micron or less Fluids To insure ultimate component life, use premium quality hydraulic oils. Fluids with effective quantities of antiwear agents or additives, (such as Mobil Oil DTE-26), are highly recommended. Viscosity Maximum Minimum 0 centistokes 00 SSU 13.5 centistokes 70 SSU Recommended Temperature Range - C (- F) to 82 C (1 F) Case Drain Precaution If outlet port exceeds, the external case drain should be used with no more than back pressure. High Speed Dimensions Published dimensions are nominal. Allowances should be made for dimensional variations of cast parts. Installation Requirements Pulleys, sprockets, and belts should be properly aligned on the shaft; and fan blades should be properly sized to prevent excessive thrust loads. Shaft Seal The standard Nitrile shaft seal is adequate for most applications. For applications which involve shaft speeds above 20 rpm or synthetic fluids, the operational Viton shaft seal should be specified. Static Seals All the o-rings included within the motor and the shaft dust seal are Nitrile. They may be used with all types of hydraulic fluids. However, since these seals swell after exposure to ester base synthetic fluids, they should be replaced if the motor is repaired. Motor Precaution A hydraulic motor is not designed to hold a suspended load. Therefore, if the application requires a locked position, a mechanical holding device (such as a brake) must be employed. Consult factory for availability. For different operating conditions, consult the factory. 233