VG Load-Independent roportional Valves Outstanding Control recise Operation
Modular valve design for flexible system configuration Easy system set-up and installation using proven VE technology Load-sensing technology for high efficiency and low energy consumption recision operation with load-independent flow control SIL 2 certified digital actuator (VED-CX)
Outstanding Control for all Your pplication Needs oday, OEMs are faced with two compelling events that challenge vehicle design and development: increasingly stringent engine emissions regulations (ier IV/Stage IV), and new vehicle safety legislation. o compensate for the reduced power levels of emissions-compliant engines, overall vehicle efficiency must be optimized. Intelligent system solutions are also needed to comply with the new safety standards and help speed up vehicle design and qualification. With electronic control, load-sensing and a flexible, modular design, our VG loadindependent proportional valves enable our customers to meet these challenges. Flexible System Design Our portfolio of VG valves provide customers with exceptional flexibility in system design. he modular design of VG accommodates future control variations and gives you an almost infinite number of configurations. Load-sensing technology also means that wear and tear on other components in the system is reduced, which helps extend vehicle life. roviding outstanding control, day in and day out, our high-quality valves are built to last. dvanced Electronic ctuators We offer a full range of electronic actuators, from simple on/off solutions, to state-ofthe-art CN bus communication. Our advanced VED-CC and VED-CX digital actuators are specifically designed for J1939/ISOUS rotocol and CNopen systems. VED-CX is also SIL 2 certified (Safety Integrity Level 2 according to IEC 61508), to help comply with the demands of the European Machinery Directive 2006/42/EC and reduce the time and costs associated with system qualification and vehicle certification. Global Manufacturing and Support Our worldwide network of sales companies, distributors, and authorized service centers is ready with after-sales support and product service when you need it. Contact your local Sauer-Danfoss representative to find out how we can help increase overall vehicle efficiency, reduce costs and improve productivity. VED-CX uilt in safety switch V asic work module Our VED-CX actuator is SIL 2 certified (Safety Integrity Level 2 according to IEC 61508), to help comply with the demands of the European Machinery Directive 2006/42/EC. VSK Module with oil supply cut off functionality Common oil supply and tank reservoir Neighbor monitoring ower supply for solenoid valves CN communication ower supply for electronics
VG 32 Our VG 32 range of load-independent proportional valves operate with compensated flow up to 130 l/min [34.4 gal/min] and work port pressure up to 400 bar [5800 psi]. Designed for maximum flexibility, VG 32 valves reduce heat generation and increase efficiency and power density, which helps to meet the challenges posed by new engine emissions legislation. p From simple load-sensing, to advanced electrically controlled loadindependent proportional valves, the modular design of VG 32 makes it possible to design a valve group that precisely meets all of your application requirements. No matter which combination of valves is specified, the compact, external dimensions of the valve remain unchanged. General VG 32 Features: Load-independent flow control for precise operation and M improved productivity Load-sensing technology for higher efficiency, safety, LS reduced energy consumption, and longer system life Configurable as advanced electrically controlled proportional valve as well as load-sensing directional control valve Modular design, providing a wide range of configuration possibilities Up to twelve basic sections per valve group (maximum flow per section: 130 l/min [34.4 gal/min]) LS LS revention against work port pressure build up in neutral Individual work port pressure setting Open spool-ends for mechanical actuation Zero-leakage work modules Meter-out compensation for negative load control Can be configured in combination with our VG 100 and VG 120 valves for maximum flexibility Mechanical, hydraulic, and electrical actuation options
VG 100 Our highly efficient post-compensated proportional valve VG 100 provides compensated flow up to 180 l/min [47.6 gal/min] and work port pressure up to 350 bar [5076 psi]. ost-compensated flow sharing valves are able to decrease oil flow to all basic work functions in case of reduced supply from the pump. Flow sharing enables design engineers to decrease pump size, while still maintaining optimal machine performance. Downsizing the pump provides incremental power and cost savings when using a variable displacement pump and substantial power savings when using a fixed displacement pump. New engine emissions regulations (ier IV/Stage IV) create a number of challenges for vehicle designers. hese include additional heat rejection, net vehicle power reduction and reduced hydraulic flow. o help meet these challenges, flow sharing can be used to help improve overall vehicle efficiency reducing wasted power while increasing vehicle productivity. ort General VG 100 Features: Flow sharing for maximum controllability and safety Load-independent flow control for precise operation and improved productivity Load-sensing technology for higher efficiency, safety, reduced energy consumption, and longer system lifetime Configurable as advanced electrically, or mechanically operated proportional load-sensing valve Modular design providing a wide range of configuration possibilities max.3.19 1) Up to eight different sections per valve group 330 (maximum flow per section: 180 l/min [47.6 gal/min]) Can be configured in combination with VG 32 valves for maximum flexibility Open spool-ends for mechanical actuation Mechanical, hydraulic, and electrical actuation options Optimized return flow characteristics, which minimizes pressure loss
VG 120 Our VG 120 load-independent proportional valve has been designed for the toughest applications with compensated flow up to 240 l/min [63.4 gal/min] and work port pressure up to 400 bar [5800 psi]. he VG 120 load-sensing proportional valve is a robust solution that combines both directional and flow control. Supplied as a complete valve group, VG 120 can be tailored to meet specific customer requirements. his exceptionally high level of flexibility enables easy modification of existing valve groups to suit a range of vehicle operating requirements. X-X p max X X General VG 120 Features: Load-independent flow control for precise operation and improved productivity Load-sensing technology for higher efficiency, safety, reduced energy consumption, and longer system life Modular design providing a wide range of configuration possibilities Up to eight basic sections per valve group (maximum flow per section: 240 l/min [63.4 gal/min]). LS Mechanical, hydraulic, and electrical actuation options Work section pressure limiter Flange port Can be configured in combination with our VG 32 valves for maximum flexibility
VG Valves Selection Guide Use our selection guide to identify the valve options that suit your specific application requirements. For further information about our valves portfolio, please contact your Sauer-Danfoss representative. Flow Range up to 130 l/min Flow Range up to 180 l/min Flow Range up to 240 l/min Mechanical Features VG32 Inlet Sections VG100 Inlet Sections VG120 Inlet Sections Open centre Open centre Open centre Closed centre Closed centre Closed centre riority function riority function ressure relief valve ressure relief valve ressure relief valve High pressure carry over Shock valve Midinlet VG32 Work Sections VG100 Work Sections VG120 Work Sections Directional control valve Check valve re-compensated re-compensated ost Compensated Float option Float option Shock valve Shock valve Shock valve Individual port pressure setting ilot operated zero leakage ports ilot operated zero leakage ports Meter-in/-out compensation Mechanical/Hydraulic/Electrical ctuation Mechanical/Hydraulic/Electrical ctuation Mechanical/Hydraulic/Electrical ctuation EH Features Electrohydraulic ctuator Electrohydraulic ctuator Electrohydraulic ctuator ON/OFF control ON/OFF control ON/OFF control roportional control roportional control roportional control Multivoltage supply 11-32 VDC Multivoltage supply 11-32 VDC Multivoltage supply 11-32 VDC Ratiometric controlled Ratiometric controlled Ratiometric controlled WM controlled WM controlled Current control Current control SE J1939/ISOUS protocol SE J1939/ISOUS protocol CNopen protocol CNopen protocol SIL2 approval 3.46(88) EX EX For further information visit at www.sauer-danfoss.com//valves.
VE Electrohydraulic ctuator Joystick (rof1) roportional valve group (VG100) ackhoe - + attery Easy and fast valve configuration and user friendly electrical actuator interface. When it comes to the design, manufacture, and application of intelligent, electronically controlled valve solutions, Sauer-Danfoss leads the way. We introduced the market s first electrical actuators p more than three decades ago and our portfolio now includes more than 50 different versions of our VE actuator. We have the experience and flexibility to meet any application requirement. Our electrical actuators make valve control easy. General VE Features: Compensates for system induced flow forces Work area ambient temperatures from -30 C to +60 C [-22 F to +140 F] and oil temperatures from -30 C to +90 C [-22 F to 194 F]. No temperature drift LUS+1 Compliant Low hysteresis Immune to changes with viscosity limits of 4 mm 2 /s to 460 mm 2 /s Immune to supply voltage variations Voltage control I 65, 66 and 67 rated Fault monitoring that monitors valve operation Full plug and perform capability Easy setup and installation speeds up time to market vailable with a wide range of different connectors Multi voltage supply range from 11-32 VDC Current control option available, both with and without spool position feedback
VED dvanced Digital Control Joystick (rof1) Fork erminal (D600) CN us roportional valve group (VG32) elescope oom lift Microcontroller (LUS+1 M ) Service tool Figure 4: XXXXXXXX From simple configurations to advanced digital systems. Our portfolio of high-performance VE actuators features VED-CC and VED-CX, advanced digital actuators specifically designed for J1939/ISOUS rotocol and CNopen systems. long with analogue position control circuits, VED-CC and CX also contain a digital circuit that enables flow control via CN communication. he result is cutting-edge digital control, advanced diagnostic functions and the ability to provide a very high level of safety. he ISO 11783 compliant VED-CC has been specifically designed for off-highway vehicles, from agriculture, construction and road building, to materials handling, forestry and turf care. Our VED-CX actuator is also SIL 2 certified. his helps reduce the time and cost associated with system qualification and vehicle certification, required to meet the demands of Machinery Directive 2006/42/EC and related safety standards. General VED Features: 3.46(88) ISOUS CN control Flow control dvanced performance settings Detailed status feedback User selectable, progressive flow characteristics dvanced built-in diagnostic functions Environmental robustness identical to analog VE 0.94(24) max.3.19 (81) VED-CX is SIL 2 certified according to IEC 61508 CNopen protocol (Ci 3.01 and Ci 4.08) ower consumption <9 W
Efficient Load-sensing echnology VG load-independent proportional valves enable our customers to improve overall vehicle efficiency and save energy. While loadsensing technology itself is not new, VG valves can help meet the demands of the ier IV/Stage IV engine emissions regulations by minimizing power losses in the hydraulic system. Improve Hydraulic System Efficiency Energy losses in a hydraulic system can be greatly reduced depending on system design. For example, the difference in efficiency between load-sensing and conventional hydraulic systems can be seen in the four graphs below. y using VG loadsensing technology in combination with a variable displacement pump, it s possible to achieve a significant reduction in energy loss. his increases overall vehicle efficiency and performance, improves productivity and helps reduce total cost of ownership. dditional load-sensing benefits include: Longer hydraulic component life, especially for pumps, due to reduced load Faster and more accurate control, independent of load Often a reduced size of pump Smaller cooler or no cooler at all, due to reduced heat load Reduced noise levels as the hydraulic components are only subjected to the oil flow and pressure necessary in a given load situation. Q Q 3 3 2 Loss 2 Leakage compensation 1 Work done 3.46(88) 1 2 3 ump with fixed displacement, relief valve 1 Work done Loss 1 2 3 ump with variable displacement, compensated pressure Q Q 3 2 Loss 0.94(24) max.3.19 (81) 3 2 Leakage compensation Standby pressure 1 Work done 1 2 3 ump with fixed displacement, pressure matching max.12.99(330) 1 Work done Standby pressure 1 2 3 ump with variable displacement, loadsensing Learn more about our emissions solutions at www.sauer-danfoss.com/emissions.
New Standards in Safety high level of safety has always been a priority when it comes to VG valves. nticipating the demands of new safety legislation, we have been developing products that help OEMs comply with the requirements of the revised European Machinery Directive (2006/42/EC) and related standards. hese include our SIL 2 certified (Safety Integrity Level 2 according to IEC 61508) digital actuator, VED-CX, and oil supply cut-off module, VSK. SIL 2 Certified Electronic ctuator When using VED-CX together with VG valves and VSK, oil flow is controlled locally by the valve group. his shuts down work function oil flow without influencing any other vehicle functions. VED-CX is also able to perform independent system monitoring and diagnostics. his means that it does not require input from a microcontroller in order to determine whether a system malfunction has occurred. In the event of a signal loss or interruption, oil flow is cut-off and the valve is brought to a safe state fast. ased on proven VE technology, VED-CX operates using a selfand neighbor-monitoring process, combined with the ability to shut down all neighbor modules. Spool movement, internal electronics, and software processes are monitored redundantly. New Safety Regulations and Related Standards European safety legislation has revised Machinery Directive 2006/42/EC and applies to all vehicles built in or shipped to Europe after December 29, 2009. his revision means that OEMs must perform and document a hazard and risk analysis for all vehicle functions. Risk analysis must follow a functional safety standard, for example, ISO 13849 or ISO 25119. he outcome of the analysis is a SIL rating (Safety Integrity Level) or L (erformance Level), which is used to identify the minimum safety requirements for each vehicle function. 2.68(68) 0.85(21,5) 3.46(88) ased on the derived SIL or L, a system architecture (category) is chosen for the safety function, and then verified. he challenge for OEMs is to design and verify vehicle functions in order to meet a specific SIL or L identified by the hazard and risk analysis. o help our customers meet this challenge, Sauer-Danfoss is developing new products, in some cases pre-qualified, to help comply with the new safety standards and European law. We are working closely with our customers, to help speed up system development and qualification, reduce total costs, and bring vehicles to market faster. 2006/42/EC released in 2006 max.3.19 1) Machinery Directive (EU Law) Harmonized Standards Domain specific standards 98/37/EC EN 954-1 2006/42/EC effective Dec 29 2009 Extension EN 954-1 obsolete Dec 31 2011 2006/42/EC EN/ISO 13849-1 max.12.99(330) ISO 15998 Earth - moving machinery ISO 25119 griculture and Forestry Overview of machinery directives and harmonized standards. Learn more at www.sauer-danfoss.com/functionalsafety.
Sauer-Danfoss is a global manufacturer and supplier of high-quality hydraulic and electronic components. We specialize in providing state-of-the-art technology and solutions that excel in the harsh operating conditions of the mobile off-highway market. uilding on our extensive applications expertise, we work closely with our customers to ensure exceptional performance for a broad range of offhighway vehicles. We help OEMs around the world speed up system development, reduce costs and bring vehicles to market faster. Sauer-Danfoss Your Strongest artner in Mobile Hydraulics. roducts we offer: ent xis Motors Closed Circuit xial iston umps and Motors Displays Electrohydraulic ower Steering Electrohydraulics Hydraulic ower Steering Integrated Systems Joysticks and Control Handles Microcontrollers and Software Open Circuit xial iston umps Orbital Motors LUS+1 GUIDE roportional Valves Sensors Steering ransit Mixer Drives Wherever off-highway vehicles are at work, so is Sauer-Danfoss. We offer expert worldwide support for our customers, ensuring the best possible solutions for outstanding performance. nd with an extensive network of Global Service artners, we also provide comprehensive global service for all of our components. Go to www.sauer-danfoss.com for further product information. lease contact the Sauer-Danfoss representative nearest you. Sauer-Danfoss (US) Company 2800 East 13th Street mes, I 50010, US hone: +1 515 239-6000 Fax: +1 515 239 6618 Sauer-Danfoss GmbH & Co. OHG ostfach 2460, D-24531 Neumünster Krokamp 35, D-24539 Neumünster, Germany hone: +49 4321 871-0 Fax: +49 4321 871 122 Sauer-Danfoss ps Nordborgvej 81 DK-6430 Nordborg, Denmark hone: +45 7488 4444 Fax: +45 7488 4400 Sauer-Danfoss-Daikin LD. Shin-Osaka ERSKI 3rd ldg. 6F 1-5-28 Nishimiyahara, Yodogawa-ku Osaka 532-0004, Japan hone: +81 6 6395 6066 Fax: +81 6 6395 8585 www.sauer-danfoss.com 2011 Sauer-Danfoss. ll rights reserved. L1107047 Rev Feb 2011 Sauer-Danfoss accepts no responsibility for possible errors in catalogs, brochures and other printed material. Sauer -Danfoss reserves the right to alter its products without prior notice. his also applies to products already ordered provided that such alterations can be made without affecting agreed specifications. ll trademarks in this material are properties of their respective owners. Sauer-Danfoss, the Sauer-Danfoss logotype, the Sauer-Danfoss S-icon, LUS+1, What really matters is inside and Know-How in Motion are trademarks of the Sauer-Danfoss Group.