NFP Interchangeable ir ylinder Medium Duty Series Series N ø.5", ø2", ø2.5", ø3.25", ø4" P 2 M2 2 S 76 85 95 P95 Medium Duty.5 to 4" Bore 2 Different NFP Mounting Options Non-rotating Option Tandem ylinder Option uto Switch apable NM N 2-6-5-
2 NFP Interchangeable ir ylinder Series N Improved cushion capacity Floating cushion seal design eliminates piston rod bouncing due to cracking pressure at beginning of stroke. ompact and lightweight design The square covers are made of an aluminum die-casting and provide a lower cost, lighterweight product. Increased kinetic energy absorption The absorption of kinetic energy has been increased by nearly 3% through increase cushion volume and the use of a new cushion seal. ø.5", ø2", ø2.5", ø3.25", ø4" Full port design llows for improved piston breakaway. Full range of NFP interchangeable mounting configurations Mounting dimensions are in accordance with NSI (NFP) T3.6.7 2-996, Fluid Power Systems and products - Square Head Industrial ylinders - Mounting Dimensions. P 2 M2 2 S 76 85 95 P95 NM N 2-6-5-2 6-5-3
NFP Interchangeable ylinder: Standard Type Double cting, Single od (Medium Duty) Series N Inch size: ø.5", ø2", ø2.5", ø3.25", ø4" 3 Built-in magnet Nil None D W/ auto switch (Magnetic piston) Style Nil K W M Standard cylinder Non-rotating cylinder Double rod Male rod stud Mounting style B MX L MS F MF MF2 MS4 D MP2 T MT4 MP4 X S U MP MS2 MT MT2 N D B 5-4 -- 54 XB5 Basic style Foot style od side flange style Head side flange style Side tapped style Double detachable head side clevis style enter trunnion style Single detachable head side clevis style Double head side clevis style Side lug style od side trunnion style Head side trunnion style Mounting Bracket Part No. Bore size 5 2 25 325.5" 2" 2.5" 3.25" 4" 4 For larger bore sizes up to 32" bore. Please consult T: N34. Standard stroke Inches Stroke Hundredths of an inch How to Order od boot Nil None Nylon K Neoprene ir cushion Nil N H Both ends None Head end od end Option B5 B6 B7 B9 6 8 9 22 Oversized rod High temperature Low temperature Low speed Stainless steel piston rod djustable stroke/xtend djustable stroke/eturn Dual operation/double rod Dual operation/single rod Fluoro rubber seals With coil scraper 35 For special rod end modifications, please see page 6-5-33. Number of auto switches Nil S 3 n 2 pcs. pcs. 3 pcs. n pcs. uto switch Nil Without auto switch For the applicable auto switch model, refer to the table on page 6-5-7. uto switches are shipped together, (but not assembled.) Mounting bracket Bore size Part no. 5 (.5") 2 (2") 25 (2.5") 325 (3.25") 4 (4") Foot N-L5 N-L2 N-L25 N-L325 N-L4 Flange Double clevis (MP2) Single clevis N-F5 N-F2 N-F25 N-F325 N-D5 N-D2 N-D25 N-D325 N-5 N-2 N-25 N-325 N-F4 N-D4 N-4 Side lug Double clevis (MP) N-S5 N5 N-S2 N2 N-S25 N25 N-S325 N325 N-S4 N4 These kits are for standard single rod/double acting cylinders without options. For option kits, please contact your local SM sales office. One kit required per cylinder. The SM N expanded Series NFP Industrial Interchangeable Pneumatic ylinders are now available in bore sizes ranging from 5"-8" Medium Duty, and.5"-4" Heavy Duty. The N xpanded Series ylinders offer: eplaceable od land full range of NFP interchangeable mounting configurations. vailable in three construction types: luminum, Steel, and Stainless steel omposite fiber tube optional. Fully adjustable cushion For further information, please consult T: N34 or contact your local SM sales office. 6-5-4
NFP Interchangeable ir ylinder Medium Duty Series Series N 4 Specifications Base Material/Surface Treatment Description Material Note over luminum alloy Silver paint Tube luminum alloy Hard alumite Seal Nitrile rubber PLD, PLP Piston rod arbon steel Hard chrom plating Piston luminum alloy hromate To calculate thrust forces not shown in the table, multiply operating pressure by piston area. How to use this table. Locate column with desired operating pressure. 2. Move down that column and locate the thrust value which is equal (or the next larger to the force to be delivered by the cylinder). 3. On that same line, locate in the first (left) column the bore size recommended for your application. Note) These are guide lines only, which must be substantiated using additional data specific to your application. To calculate pull forces not shown in the table, use the following formula: Pull Force = (Piston area od area) x Working pressure How to read this table. To find the force on the pull stroke, locate the required piston rod diameter in the left most column. 2. Moving to the right, locate the required working pressure. 3. Deduct the value shown at the intersection from the push stroke force value determined from the Push Stroke table. The resultant is the available pull stroke table. Fluid Lubrication Max. operating pressure Min. operating pressure mbient & fluid temperature Piston speed ushion Mounting Type Non-rotating accuracy Standard ir Non-lube 25 psi (.75 MPa) 8 psi (.6 MPa) 4 to 4 F (5 to 6 ) 2 to 2 in/s (5 to 5 mm/s) Double rod Non-rotating rod ir ir Non-lube Non-lube 25 psi (.75 MPa) 25 psi (.75 MPa) 8 psi (.6 MPa) 5 psi (. MPa) 4 to 4 F (5 to 6 ) to 4 F (5 to 6 ) 2 to 2 in/s (5 to 5 mm/s) ir cushion standard 2 to 2 in/s (5 to 5 mm/s) od and head side trunnion maximum operating pressure for 325 and 4 bore is up to 5 psi. Standard Stroke Bore size (in) Standard stroke Maximum stroke.5" 2", 2.5" 3.25", 4" Weight/luminum Tube Bore size (in) 5 (.5") 2 (2") 25 (2.5") 325 (3.25") 4 (4") Basic style.58 2.35 3.9 6.3 7.79 Foot mounting style.95 2.86 3.8 7.45.2 Basic Flange mounting style 2.3 3.22 4.45 8.85.66 weight levis mounting style 2.27 3.23 4.28 8.95.4 Trunnion mounting style 2.79 3.8 5.5.5 3.5 dd l weight per each 2" of stroke Basic style, Foot style, od side flange style, Head side flange style, levis style, Side tapped style, enter trunnion style, Head side trunnion style, Side lug style, od side trunnion style N/, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2,, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28, For all mountings style.38.48.5.97.6 ylinder Bore and Force: Push Stroke Bore size Piston area Force (lbs); Push stroke Operating medium pressure (PSI) (in) (in) 5 6 8 2 25.5.767 88 6 4 77 353 442 2 3.42 57 88 25 34 628 785 2.5 4.99 245 295 393 49 982 227 3.25 8.296 45 498 664 83 659 274 4 2.566 628 754 5 257 253 342 ylinder Bore and Force: Pull Stroke Basic style, Foot style, Flange style, enter trunnion style, Side tapped style od side trunnion style Piston Piston Force (lbs); Pull stroke (Deduct the listed thrusts corresponding rod rod to the rod size from push stroke pressure) diameter area Operating medium pressure (psi) (in) (in) 5 6 8 2 25.625.37 5 8 25 3 6 77.785 39 47 63 79 57 96.375.485 74 89 9 48 297 37 N/ Basic style, Foot style, levis style, od side flange style, Head side flange style, enter trunnion style, Side tapped style, Side lug style N/ (in) Please consult with SM. (lbs) P 2 M2 2 S 76 85 95 P95 NM N 2-6-5-5
Series N 5 onstruction eplacement Parts No. Description q od cover w Head cover e ylinder tube r Piston rod t Piston y ushion ring u od bushing i ushion valve o Tie-rod! Tie-rod nut! etaining ring!2 od seal retainer!3 ushion seal!4 od seal!5 Piston seal!6 ushion valve seal!7 ylinder tube gasket!8 Piston gasket!9 Wear ring @ od jam nut omponents included in a seal kit. How to Order Seal Kit N W 5 Material luminum alloy luminum alloy luminum alloy arbon steel luminum alloy Brass Bronze casted arbon steel arbon steel arbon steel arbon steel arbon steel Urethan rubber NB NB NB NB NB esin arbon steel PS Option W K Single rod Double rod Non-rotating Bore 5 2 25 325 4 Option B5 B6 B7 vailable for 5, 2 and 25 bores only. Use single rod designation when ordering X kit. Note: X seal kit order 2 single rod kits. Not available with W and K option Oversized rod High temperature Low temperature Dual operation/single rod 6-5-6
6 Series N uto Switch Specifications pplicable uto Switch/efer to page 6-6- for further information on auto switches. Type eed switch Solid state switch Special function Diagnosis indication (2-color) Diagnosis indication (2-color) Water resistant (2-color) Diagnosis output (2-color) With timer lectrical entry rommet rommet Note) Lead wire length symbols:.5 m Nil (xample) 53 3 m L (xample) 53L 5 m Z (xample) 53Z Indicator light es es Wiring (Output) 2-wire 3-wire (quiv. NPN) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 4-wire (NPN) 3-wire (NPN) Load voltage D 24 V 2 V V, 2 V 5 V 2 V 2 V or less 24 V 5 V, 2 V 5 V, 2 V V, 2 V 2 V 5 V, 2 V 24 V 2 V 5 V, 2 V uto switch model 53 54 56 59W 64 67 F59 F5P 5 59 F59W F5PW 59W F5BL F59F F5NTL Lead wire length (m) Note).5 (Nil) 3 (L) 5 (Z) onnector pplicable load PL elay, PL I circuit elay, PL PL I circuit I circuit I circuit Solid state auto switches marked with are produced upon receipt of order. elay, PL P 2 M2 2 S 76 85 95 P95 NM N 2-6-5-7
Series N 7 Basic Style: NB (MX mounting style) ZB + Stroke 2- (NPTF) Bore size (in) MM B B D DD LF P ZB 5 (.5") 7/6-2 2.2 /8 /8 9/6 /4-28 2.3.26..43.7 3 2.36 4 2 (2") 7/6-2 2.6 /8 /8 9/6 5/6-24 2 /2.3.26.6.84.7 3 2.4 4 25 (2.5") 7/6-2 3. /8 /8 9/6 5/6-24 3.3.6 2.9.75 3 2.48 4 7/8 325 (3.25") -6 /8 3.9 /2 /2 /2 7/8-24 3 /2.57.8 2.76 2.34 4 /4 5 53/64 4 (4") -6 /8 4.7 /2 /2 /2 7/8-24 4 /2 /2.57.8 3.32 2.34 4 /4 5 53/64 Foot Style: NL (MS mounting style) falts Z + Stroke X + Stroke 2- (NPTF) H T ømm ømm S 6-B (Hole) O L F S + Stroke L O Bore size (in) MM B H L O T B B D DD F S P LF 5 (.5") 7/6-2 2.2 2 3/6 3/6 7/6 /8 /8 /8 9/6 /4-28 2.3.26..43 /4.7 2.36 3 2 (2") 7/6-2 2.6 2 /6 7/6 9/6 /8 /8 /8 9/6 5/6-24 2 /2.3.26.6.84.7 2.4 3 25 (2.5") 7/6-2 3. 3 /8 9/6 /8 /8 /8 9/6 5/6-24 3.3.6 2.9 2/4.75 2.48 3 325 (3.25") -6 /8 3.9 /2 3 3/6 5/6 /4 /64 /2 /2 /2 7/8-24 3 /2.57.8 2.76 2 2.34 4 /4 4 (4") -6 /8 4.7 /2 4 /2 2 /4 /4 5/64 /2 /2 /2 7/8-24 4/2 /2.57.8 3.32 3 /2 2.34 4 /4 Bore size (in) S X Z 5 (.5") 2 (2") 6 6 5 6 /6 5 6 3/6 25 (2.5") 6 /8 5 6 5/6 325 (3.25") 7 6 7/8 7 4 (4") 7 6 7/8 7 6-5-8
NFP Interchangeable ir ylinder Medium Duty Series Series N 8 od Side Flange Style: NF (MF mounting style) 4-FB (Hole) 2- (NPTF) ømm P TF W F 2 UF ZB + Stroke M2 Bore size (in) MM 5 (.5") 7/6-2 2.2 B /8 B /8 D 9/6 2.3 F FB 5/6.26..43 TF 2 UF 3 W.7 LF 3 P 2.36 ZB 4 2 (2") 25 (2.5") 7/6-2 7/6-2 2.6 3. /8 /8 /8 /8 9/6 9/6 2 /2 3.3.26.3.6.6.84 2.9 3 3 7/8 4 /8 4.7.75 3 3 2.4 2.48 4 4 7/8 325 (3.25") 4 (4") -6-6 /8 /8 3.9 4.7 /2 /2 /2 /2 /2 /2 7/8 7/8 3 4 /2 /2 /2 7/6 7/6.57.57.8.8 2.76 3.32 4 /6 5 7/6 5 /2 6 /4 2.34 2.34 4 /4 4 /4 5 53/64 5 53/64 2 S Head Side Flange Style: N (MF2 mounting style) 76 85 95 2- (NPTF) 4-FB (Hole) P95 NM N ømm TF 2- XF + Stroke F UF ZF + Stroke Bore size (in) MM B B D F FB TF UF P XF ZF 5 (.5") 7/6-2 2.2 /8 /8 9/6 2.3 5/6.26..43 2 3.7 2.36 4 5 2 (2") 7/6-2 2.6 /8 /8 9/6 2 /2.3.26.6.84 3 4 /8.7 2.4 4 5 25 (2.5") 7/6-2 3. /8 /8 9/6 3.3.6 2.9 3 7/8 4.75 2.48 4 5 /8 325 (3.25") -6 /8 3.9 /2 /2 /2 7/8 3 /2 7/6.57.8 2.76 4 /6 5 /2 2.34 5 6 /4 4 (4") -6 /8 4.7 /2 /2 /2 7/8 4 /2 /2 7/6.57.8 3.32 5 7/6 6 /4 2.34 5 6 /4 6-5-9
Series N 9 Side Tapped Style: N (MS4 mounting style) 2- (NPTF) TN 4-NT Depth ND XT SN + Stroke ZB + Stroke Bore size (in) MM B B D DD /2 ND NT TN XT LF P SN ZB 5 (.5") 7/6-2 2.2 /8 /8 9/6 /4-28 2.3.26..43 9/32 /4-2 5/6.7 3 2.36 2 /4 4 2 (2") 7/6-2 2.6 /8 /8 9/6 5/6-24 2 /2 /4.3.26.6.84 7/6 5/6-8 7/8 5/6.7 3 2.4 2 /4 4 25 (2.5") 7/6-2 3. /8 /8 9/6 5/6-24 3 /2.3.6 2.9 9/32-6 /4 5/6.75 3 2.48 2 4 7/8 325 (3.25") -6 /8 3.9 /2 /2 /2 7/8-24 3 7/8 /2.57.8 2.76 /2-3 /2 2 7/6 2.34 4 /4 2 5 53/64 4 (4") -6 /8 4.7 /2 /2 /2 7/8-24 4 /2 2 /4 /2.57.8 3.32 /2-3 2 /6 2 7/6 2.34 4 /4 2 5 53/64 Double Detachable Head Side levis Style: ND (MP2 mounting style) 2- (NPTF) F L D W W ømm /2 ømm XD + Stroke L M B ZD + Stroke Bore size (in) MM B B D W D DD F L L M XD LF P ZD 5 (.5") 7/6-2 2.2 /8 /2 /2 9/6 /4-28 2.3.26..43 /2 5.7 3 2.36 6 /4 2 (2") 7/6-2 2.6 /8 /2 /2 9/6 5/6-24 2 /2.3.26.6.84 /2 5.7 3 2.4 6 /4 25 (2.5") 7/6-2 3. /8 /2 /2 9/6 5/6-24 3.3.6 2.9 /2 5 7/8.75 3 2.48 6 325 (3.25") -6 /8 3.9 /2 /2 /4 7/8-24 3 /2.57.8 2.76 /4 7 /2 2.34 4 /4 8 /4 4 (4") -6 /8 4.7 /2 /2 /4 7/8-24 4 /2 /2.57.8 3.32 /4 7 /2 2.34 4 /4 8 /4 6-5-
NFP Interchangeable ir ylinder Medium Duty Series Series N Head Side Trunnion Style: N (MT2 mounting style) 2- (NPTF) ømm P ir cushion adj. øtd TL TL 2 M2 ZB + Stroke Bore size (in) MM B D DD TD. TL LF P ZB 5 (.5") 7/6-2 2.2 /8 9/6 /4-28 2.3 2 (2") 7/6-2 2.6 /8 9/6 5/6-24 2 /2.3.26.26..6.43.84.7.7 3 3 2.36 2.4 4 4 25 (2.5") 7/6-2 3. /8 9/6 5/6-24 3 325 (3.25") -6 /8 3.9 /2 /2 7/8-24 3 4 (4") -6 /8 4.7 /2 /2 7/8-24 4 /2.3 /2.57 /2.57.6.8.8 2.9 2.76 3.32.75 2.34 2.34 3 4 /4 4 /4 2.48 4 7/8 5 53/64 5 53/64 2 S od Side Trunnion Style: NU (MT mounting style) 76 85 95. øtd ømm 2- (NPTF) P95 NM N ir cushion adj. 2- TL TL ZB + Stroke Bore size (in) MM B B D DD TD. TL LF P ZB 5 (.5") 7/6-2 2.2 /8 /8 9/6 /4-28 2.3.26..43.7 3 2.36 4 2 (2") 7/6-2 2.6 /8 /8 9/6 5/6-24 2 /2.3.26.6.84.7 3 2.4 4 25 (2.5") 7/6-2 3. /8 /8 9/6 5/6-24 3.3.6 2.9.75 3 2.48 4 7/8 325 (3.25") -6 /8 3.9 /2 /2 /2 7/8-24 3 /2.57.8 2.76 2.34 4 /4 5 53/64 4 (4") -6 /8 4.7 /2 /2 /2 7/8-24 4 /2 /2.57.8 3.32 2.34 4 /4 5 53/64 6-5-
Series N enter Trunnion Style: NT (MT4 mounting style) XI + /2 stroke 2- (NPTF) ømm TT Z Bore size (in) MM B B D DD TD. TL TM TT UM UV P LF XI ZP 5 (.5") 7/6-2 2.2 /8 /8 9/6 /4-28 2.3.26..43 2 /2.8 4 /2 2.7 2.36 3 2.89 4 2 (2") 7/6-2 2.6 /8 /8 9/6 5/6-24 2 /2.3.26.6.84 3.8 5 2.56.7 2.4 3 2.9 4 25 (2.5") 7/6-2 3. /8 /8 9/6 5/6-24 3.3.6 2.9 3 /2.8 5 /2 3.39.75 2.48 3 2.99 4 7/8 325 (3.25") -6 /8 3.9 /2 /2 /2 7/8-24 3 /2.57.8 2.76 4 /2.34 6 /2 4.33 2.34 4 /4 3.7 5 53/64 4 (4") -6 /8 4.7 /2 /2 /2 7/8-24 4 /2 /2.57.8 3.32 5 /4.57 7 /4 5.2 2.34 4 /4 3.74 5 53/64 Single Detachable Head Side levis Style: N (MP4 mounting style) 2- (NPTF) ød ømm L B F L M XD + Stroke ZD + Stroke Bore size (in) MM B B D D DD F L L M XD LF P ZD 5 (.5") 7/6-2 2.2 /8 /2 9/6 /4-28 2.3.26..43 /2 5.7 3 2.36 6 /4 2 (2") 7/6-2 2.6 /8 /2 9/6 5/6-24 2 /2.3.26.6.84 /2 5.7 3 2.4 6 /4 25 (2.5") 7/6-2 3. /8 /2 9/6 5/6-24 3.3.6 2.9 /2 5 7/8.75 3 2.48 6 325 (3.25") -6 /8 3.9 /2 /2 /4 7/8-24 3 /2.57.8 2.76 /4 7 /2 2.34 4 /4 8 /4 4 (4") -6 /8 4.7 /2 /2 /4 7/8-24 4 /2 /2.57.8 3.32 /4 7 /2 2.34 4 /4 8 /4 6-5-2
NFP Interchangeable ir ylinder Medium Duty Series Series N 2 Double Head Side levis Style: NX (MP mounting style) 2- (NPTF) F S.H..S. ød L W W ømm P 2 ZB + Stroke XD + Stroke L M B M2 Bore size (in) MM B B D W D DD F L L M XD LF P ZB 5 (.5 ) 2 (2 ) 7/6-2 2.2 /8 7/6-2 2.6 /8 /2 /2 /2 /2 9/6 /4-28 2 9/6 5/6-24 2 /2.3.3.26.26..6.43.84.62.62.75.75.62.62 5 5.7.7 3 3 2.36 2.4 4 4 2 25 (2.5 ) 7/6-2 3. /8 325 (3.25 ) -6 /8 3.9 /2 /2 /4 /2 /2 9/6 5/6-24 3 7/8-24 3 /2.3.57.6.8 2.9 2.76.62.75.5.25.62.87 5 7/8 7 /2.75 2.34 3 4 /4 2.48 4 7/8 5 53/64 S 4 (4 ) -6 /8 4.7 /2 /2 /4 7/8-24 4 /2 /2.57.8 3.32.5.25.87 7 /2 2.34 4 /4 5 53/64 76 Side Lug Mounting Style: NS (MS2 mounting style) 85 95 øsb Screw (4) Hole ZB + Stroke 2- (NPTF) P95 NM N ømm /2 ST TS US SW XS SU SS + Stroke SU SW S 2- Bore size (in) MM B D DD LF P SB SS ST SU SW S TS US XS ZB 5 (.5 ) 7/6-2 /8 9/6 /4-28 2.3.26. 3.63 2.36.43 2.88.94.94 2.75 3.5.38.7 5.9 2 (2 ) 7/6-2 /8 9/6 5/6-24 2 /2.3.26.6 3.63 2.4.84 2.88.94.94 3.25 4.38.7 5.9 25 (2.5 ) 7/6-2 /8 9/6 5/6-24 3.3.6 3.75 2.48 2.9 3.94.94 3.75 4.5.38.75 5.3 325 (3.25 ) -6 /8 /2 /2 7/8-24 3 /2.57.8 4.25 2.76 /2 3.25.25 /2.25 4.75 5.75.38.88 2.34 6.38 4 (4 ) -6 /8 /2 /2 7/8-24 4 /2 /2.57.8 4.25 3.32 /2 3.25.25 /2.25 5.5 6.5.38.88 2.34 6.38 6-5-3
NFP Interchangeable ylinder: Non-rotating od Double cting, Single od (Medium Duty) Series NK Inch size: ø.5", ø2", ø2.5" 3 How to Order ND K Mounting Bore Stroke Suffix x: NDKB5-4 uto switch capable Specifications od non-rotating accuracy: ±.5 uto switch mounting available Bore size (inch) Fluid Max. operating pressure Min. operating pressure mbient and fluid temperature Piston speed ushion otational torque range Non-rotating accuracy Mounting Standard Stroke Bore size (in) Standard stroke.5, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2 2, 2.5, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24.5 2 2.5 ir 25 psi (.75 MPa) 5 psi (.6 MPa) 4 to 4 F (5 to 6 ) 2 to 2 inch/sec (5 to 5 mm/sec) ir cushion standard 3.9 lbs. in or less ±.5 Basic style, Foot style, Flange style levis style, Side tapped style enter trunnion style, Side lug style 6-5-4
NFP Interchangeable ir ylinder Medium Duty Series Non-rotating od - Basic Style/Side Tapped Style: NKB (MX mounting style)/nk(mx4 mounting style) Series NK 4 TN 4-NT Depth ND ø.63 Bore size (in) B B D DD ND NT LF P ZB TN XT SN 5 (.5") 7/6-2 2.2 /8 /8.55 /4-28 2.3.26. 9/32 /4-2.43.7 3 2.36 4 5/6 2 /4 2 (2") 7/6-2 2.6 /8 /8.55 5/6-24 2 /2.3.26.6 7/6 5/6-8.84.7 3 2.4 4 7/8 5/6 2 /4 25 (2.5") 7/6-2 3. /8 /8.55 5/6-24 3.3.6 9/32-6 2.9.75 3 2.48 4 7/8 /4 5/6 2 2- (NPTF) XT SN + Stroke ZB + Stroke P 2 M2 2 S 76 85 95 P95 NM N 2-6-5-5
Series NK 5 Non-rotating od-foot Style: NKL (MS mounting style) Z + Stroke X + Stroke 2- (NPTF) T H ø.63 O L F L O S + Stroke Bore size (in) B H L O T B B D DD F S P LF S X Z 5 (.5") 7/6-2 2.2 2 3/6 3/6 7/6 /8 /8 /8.55 /4-28 2.3.26..43 /4.7 2.36 3 6 5 6.62 2 (2") 7/6-2 2.6 2 /6 7/6 9/6 /8 /8 /8.55 5/6-24 2.5.3.26.6.84.7 2.4 3 6 5 6.97 25 (2.5") 7/6-2 3. 3 /8 9/6 /8 /8 /8.55 5/6-24 3.3.6 2.9 2 /4.75 2.48 3 6 /4 5 6.32 Non-rotating od-od Side Flange Style: NKF (MF mounting style) 4-øFB (Hole) W 2- (NPTF) F ZB + Stroke Bore size (in) B B D DD F FB TF UF W LF P ZB 5 (.5") 7/6-2 2.2 /8 /8.55 /4-28 2.3 5/6.26..43 2 3.7 3 2.36 4 2 (2") 7/6-2 2.6 /8 /8.55 5/6-24 2.5.3.26.6.84 3 4 /8.7 3 2.4 4 25 (2.5") 7/6-2 3. /8 /8.55 5/6-24 3.3.6 2.9 3 7/8 4.75 3 2.48 4 7/8 Non-rotating od-head Side Flange Style: NK (MF2 mounting style) 2- (NPTF) 4-øFB (Hole) ø.63 ø.63 S 6-øB (Hole) TF UF F TF XF + Stroke UF ZB + Stroke Bore size (in) B B D DD F FB TF UF P XF ZF 5 (.5") 7/6-2 2.2 /8 /8.55 /4-28 2.3 5/6.26..43 2 3.7 2.36 4 5 2 (2") 7/6-2 2.6 /8 /8.55 5/6-24 2.5.3.26.6.84 3 4 /8.7 2.4 4 5 25 (2.5") 7/6-2 3. /8 /8.55 5/6-24 3.3.6 2.9 3 7/8 4.75 2.48 4 5 /8 6-5-6
NFP Interchangeable ir ylinder Medium Duty Series Series NK 6 Non-rotating od-double Detachable Head Side levis Style: NKD (MP2 mounting style) 2- (NPTF) ød ø.63 Bore size (in) B 5 (.5") 7/6-2 2.2 /8 2 (2") 25 (2.5") 7/6-2 7/6-2 2.6 3. /8 /8 B D /2 /2 /2 W /2 /2 /2 D.55.55.55 DD /4-28 5/6-24 5/6-24 2 2.5 3 Bore size (in) B B D DD TD. TL TM TT UM UV P LF XI ZB 5 (.5") 7/6-2 2.2 /8 /8.55 /4-28 2.3.26..43 2.5.8 4.5 2.7 2.36 3 2.89 4 2 (2") 7/6-2 2.6 /8 /8.55 5/6-24 2.5.3.26.6.84 3.8 5 2.56.7 2.4 3 2.9 4 25 (2.5") 7/6-2 3. /8 /8.55 5/6-24 3.3.6 2.9 3.5.8 5.5 3.39.75 2.48 3 2.99 4 7/8.3.3 F.26.26.3..6.6 L.43.84 2.9 L M /2 /2 /2 Non-rotating od-enter Trunnion Style: NKT (MT4 mounting style) ø.63 XD + Stroke ZD + Stroke F XI + /2 Stroke L W B L M 2- (NPTF) W XD 5 5 5 7/8 TT ZB + Stroke LF.7 3.7 3.75 3 P 2.36 2.4 2.48 ZD 6 /4 6 /4 6 P 2 M2 2 S 76 85 95 P95 NM N 2-6-5-7
NFP Interchangeable ylinder: Standard Type Double cting, Double od (Medium Duty) Series NW Inch size: ø.5", ø2", ø2.5", ø3.25", ø4" 7 How to Order NDW Mounting Bore Stroke Suffix x: NDWB 5-4 uto switch capable Double rod Specifications Bore size (inch) Fluid Max. operating pressure Min. operating pressure mbient & fluid temperature Piston speed ushion Mounting.5 2 2.5 3.25 4 ir 25 psi (.75 MPa) 8 psi (.6 MPa) 4 to 4 F (5 to 6 ) 2 to 2 inch/sec (5 to 5 mm/sec) ir cushion standard Basic style, Foot style, Flange style enter trunnion style, od side trunnion style, Side tapped style Standard with air cushion uto switch mounting available Standard Stroke Bore size (in).5 Standard stroke, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2 2, 2.5, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24 3.25, 4, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28 6-5-8
NFP Interchangeable ir ylinder Medium Duty Series Double od-basic Style/Side Tapped Style: NWB (MX mounting style)/nw (MX4 mounting style) Series NW 8 P 2 M2 Bore size (in) MM B D DD K LD P ZM XT SD 5 (.5") 7/6-2 2.2 /8 9/6 /4-28 2.3.26.28 3.78 2.36.43.7 5.78 5/6.9 2 (2") 7/6-2 2.6 /8 9/6 5/6-24 2 /2.3.26.34 3.82 2.4.84.7 5.82 5/6.94 25 (2.5") 7/6-2 3. /8 9/6 5/6-24 3.3.34 3.98 2.48 2.9.75 5.98 5/6 2. 325 (3.25") -6 /8 3.9 /2 /2 7/8-24 3 /2.57.42 4.64 2.76 2.34 7.4 2 7/6 2.52 4 (4") -6 /8 4.7 /2 /2 7/8-24 4 /2 /2.57.42 4.64 3.32 2.34 7.4 2 7/6 2.52 2 S 76 85 95 P95 NM N 2-6-5-9
Series NW 9 Double od-foot Style: NWL (MS mounting style) ZM + 2 stroke 2- (NPTF) + Stroke + Stroke falts falts 6-øB (Hole) LD + Stroke SL + Stroke Bore size (in) MM B H L O T B D DD K S P LD SL ZM 5 (.5") 7/6-2 2.2 2 3/6 3/6 7/6 /8 /8 9/6 /4-28 2.3.26.43.28 /4.7 2.36 3.78 5.78 5.78 2 (2") 7/6-2 2.6 2 /6 7/6 9/6 /8 /8 9/6 5/6-24 2.5.3.26.84.34.7 2.4 3.82 5.82 5.82 25 (2.5") 325 (3.25") 7/6-2 -6 /8 3. 3.9 /2 3 /8 9/6 /8 /8 3 3/6 5/6 /4 /64 /2 9/6 5/6-24 3 /2 7/8-24 3.75.3 2.9 /2.57 2.76.34.42 2 /4 2.75 2.34 2.48 3.98 4.64 5.98 5.98 7.4 7.4 4 (4") -6 /8 4.7 /2 4 /2 2 /4 /4 5/64 /2 /2 7/8-24 4.5 /2.57 3.32.42 3 /2 2.34 4.64 7.4 7.4 Double od-od Side Flange Style: N (MF mounting style) 4-øFB (Hole) 2- (NPTF) + Stroke falts falts LD + Stroke ZM + 2 Stroke + Stroke Bore size (in) MM B D DD F FB K TF UF W LD P ZM 5 (.5") 7/6-2 2.2 /8 9/6 /4-28 2.3 5/6.26.28.43 2 3.7 3.78 2.36 5.78 2 (2") 7/6-2 2.6 /8 9/6 5/6-24 2.5.3.26.34.84 3 4 /8.7 3.82 2.4 5.82 25 (2.5") 7/6-2 3. /8 9/6 5/6-24 3.3.34 2.9 3 7/8 4.75 3.98 2.48 5.98 325 (3.25") -6 /8 3.9 /2 /2 7/8-24 3.75 /2 7/6.57.42 2.76 4 /6 5 /2 2.34 4.64 7.4 4 (4") -6 /8 4.7 /2 /2 7/8-24 4.5 /2 7/6.57.42 3.32 5 7/6 6 /4 3.4 2.34 4.64 7.4 6-5-2
NFP Interchangeable ir ylinder Medium Duty Series Series NW 2 Double od-enter Trunnion Style: NWT (MT4 mounting style) falts XI + /2 stroke 2- (NPTF) + Stroke falts P Bore size (in) MM 5 (.5") 2 (2") 25 (2.5") 325 (3.25") 4 (4") 7/6-2 7/6-2 7/6-2 -6-6 /8 /8 B 2.2 /8 2.6 /8 3. /8 3.9 /2 4.7 /2 /2 /2 D DD 9/6 /4-28 9/6 5/6-24 9/6 5/6-24 7/8-24 7/8-24 2.3 2.5.3 3 3.75 4.5 /2 /2.26.26.3.57.57 Bore size (in) MM B D DD K TD. TL LD P ZM 5 (.5") 7/6-2 2.2 /8 9/6 /4-28 2.3.26.28.43.7 3.78 2.36 5.78 2 (2") 7/6-2 2.6 /8 9/6 5/6-24 2.5.3.26.34.84.7 3.82 2.4 5.82 25 (2.5") 7/6-2 3. /8 9/6 5/6-24 3.3.34 2.9.75 3.98 2.48 5.98 325 (3.25") -6 /8 3.9 /2 /2 7/8-24 3.75 /2.57.42 2.76 2.34 4.64 7.4 4 (4") -6 /8 4.7 /2 /2 7/8-24 4.5 /2.57.42 3.32 2.34 4.64 7.4 K.28.34.34.42.42.43.84 2.9 2.76 3.32 TD. TL TM 2.5 3 3.5 TT.8.8.8 UM 4.5 5 5.5 UV 2 2.56 3.39.7.7.75 4.5.34 6.5 4.33 2.34 5.25.57 7.25 5.2 2.34 Double od - od Side Trunnion Style: NWU (MT mounting style) TD. falts ir cushion adj. LD + Stroke ZM + 2 stroke ZM + 2 stroke 2- (NPTF) LD + Stroke + Stroke P 2.36 2.4 2.48 + Stroke + Stroke LD 3.78 3.82 3.98 4.64 4.64 XI 2.89 2.9 2.99 3.7 3.74 falts ZM 5.78 5.82 5.98 7.4 7.4 2 M2 2 S 76 85 95 P95 NM N 2-6-5-2
Series N 2 od Boot od Boot Material Suffix for option Material Nylon K Neoprene Max. temperature is for boot only. Max. temperature 4 F (6 ) 23 F ( ) How to Order N D Mounting Bore Stroke Suffix Boot od boots are used to protect the surface of a piston rod in harsh environments. x: NDB5-2 uto switch capable od boot Nylon rod boot K Neoprene rod boot od Boot Dimensions Bore size L (in) Ø F to 2 2. to 4 4. to 6 6. to 8 8. to. to 2 2. to 4 4. to 6 6. to 2 2. to 24 24. to 28 5 (.5").75.375.734 2 (2").75.375.734 6 25 (2.5").75.375.734.5.5 2 2.5 3 3.5 4 5 6 325 (2.25").25.968.984 6 7 4 (4").25.968.984 6 7 Bore size Wf (in) to 2 2. to 4 4. to 6 6. to 8 8. to. to 2 2. to 4 4. to 6 6. to 2 2. to 24 24. to 28 5 (.5").937 2.437 2.937 3.437 3.937 4.437 4.937 5.437 6.437 2 (2").937 2.437 2.937 3.437 3.937 4.437 4.937 5.437 6.437 7.437 25 (2.5").937 2.437 2.937 3.437 3.937 4.437 4.937 5.437 6.437 7.437 325 (2.25") 2.32 2.82 3.32 3.82 4.32 4.82 5.32 5.82 6.82 7.82 8.82 4 (4") 2.32 2.82 3.32 3.82 4.32 4.82 5.32 5.82 6.82 7.82 8.82 Bore size ZB (in) to 2 2. to 4 4. to 6 6. to 8 8. to. to 2 2. to 4 4. to 6 6. to 2 2. to 24 24. to 28 5 (.5") 5.689 6.87 6.687 7.87 7.687 8.87 8.687 9.87.87 2 (2") 5.689 6.87 6.687 7.87 7.687 8.87 8.687 9.87.87.87 25 (2.5") 5.82 6.32 6.82 7.32 7.82 8.32 8.82 9.937.32.32 325 (2.25") 6.765 7.265 7.765 8.265 8.765 9.265 9.765.265.265 2.265 3.265 4 (4") 6.765 7.265 7.765 8.265 8.765 9.265 9.765.265.265 2.265 3.265 6-5-22
Series N 22 Stainless Steel od Stainless steel piston rod is used to protect in harsh or wet environments. uto switch mounting available. Low Speed Smooth movements even at.4 to 2 inch/sec uto switch mounting available. Specifications Bore size (inch) Fluid Max. operating pressure Min. operating pressure od material mbient & fluid temperature Piston speed ushion Mounting Standard Stroke Bore size (in).5 2, 2.5 3.25, 4 Specifications.5 2 2.5 3.25 4 ir 25 psi (.75 MPa) 8 psi (.6 MPa) Stainless steel 34 4 to 4 F (5 to 6 ) 2 to 2 inch/sec (5 to 5 mm/sec) ir cushion standard Basic style, Foot style, Flange style enter trunnion style, Side tapped style, levis style od side trunnion style, Head side trunnion style Side lug style Standard stroke, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28 How to Order N D Mounting Bore Stroke Suffix X6 x: NDB 5-46 uto switch capable Bore size (inch) Fluid Max. operating pressure Min. operating pressure mbient & fluid temperature Piston speed ushion Mounting Standard Stroke Bore size (in).5 2, 2.5 3.25, 4 Stainless steel rod.5 2 2.5 3.25 4 ir 25 psi (.75 MPa) 8 psi (.6 MPa) 4 to 4 F (5 to 6 ).4 to 2 inch/sec ( to 5 mm/sec) None Basic style, Foot style, Flange style enter trunnion style, Side tapped style, levis style od side trunnion style, Head side trunnion style Side lug style Standard stroke, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28 How to Order N D Mounting Bore Stroke N x: NDB 5-4NB9 uto switch capable Low friction/low speed XB9 Standard P 2 M2 2 S 76 85 95 P95 NM N 2-6-5-23
Series N 23 High Temperature Specifications Bore size (inch) Fluid Max. operating pressure Min. operating pressure mbient & fluid temperature Seal material Piston speed ushion Mounting.5 2 2.5 3.25 4 ir 25 psi (.75 MPa) 8 psi (.6 MPa) 4 to 3 F ( to 5 ) Fluoro rubber 2 to 2 inch/sec (5 to 5 mm/sec) ir cushion standard Basic style, Foot style, Flange style enter trunnion style, Side tapped style, levis style od side trunnion style, Head side trunnion style Side lug style Use at high temperature up to 3 F. Standard Stroke Bore size (in).5 2, 2.5 3.25, 4 Standard stroke, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28 How to Order N Mounting Bore Stroke Suffix XB6 x: NB 5-4B6 uto switch capable not available High temperature Low Temperature Specifications Bore size (inch) Fluid Max. operating pressure Min. operating pressure mbient & fluid temperature Seal material Piston speed ushion Mounting.5 2 2.5 3.25 4 ir 25 psi (.75 MPa) 8 psi (.6 MPa) 22 to 4 F ( 3 to 6 ) Low durometer nitril rubber 2 to 2 inch/sec (5 to 5 mm/sec) None Basic style, Foot style, Flange style enter trunnion style, Side tapped style, levis style od side trunnion style, Head side trunnion style Side lug style Use at low temperature down to 22 F. Standard Stroke Bore size (in).5 2, 2.5 3.25, 4 Standard stroke, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28 How to Order N Mounting Bore Stroke N XB7 x: NB 5-4NB7 Low temperature Standard uto switch capable not available 6-5-24
Series N 24 Oversized od Bore size (in) MM B B D DD Specifications 2 2.5 3.25 4 ir 25 psi (.75 MPa) 8 psi (.6 MPa) 4 to 4 F (5 to 6 ) 2 to 2 inch/sec (5 to 5 mm/sec) ir cushion standard Basic style, Foot style, Flange style, enter trunnion style, Side tapped style N D Mounting Bore Stroke Suffix XB5 2 (2") -6 /8 2.6 /2 /8 /2 7/8 5/6-24 2 /2.3.26.6.84 7/6 5/6-8 7/8 25 (2.5") -6 /8 3. /2 /8 /2 7/8 5/6-24 3.3.6 2.9 9/32-8 /4 325 (3.25") -4 3.9 2 /2 /4-24 3 /2.57.8 2.76 /2-3 /2 4 (4") -4 4.7 2 /2 /4-24 3 /2.57.8 3.32 /2-3 2 /6 Bore size (inch) Fluid Max.operating pressure Min.operating pressure mbient & fluid temperature Piston speed ushion Mounting Standard Stroke Bore size (in) 2, 2.5 3.25, 4 Oversized od-basic Style: NB (XB5) 4-NT Depth ND F Standard stroke, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28 How to Order Oversized od/standard x: NDB 25-2B5 uto switch capable ND NT Oversized/rod 2- (NPTF) SN + Stroke ZB + Stroke TN XT 2 5/6 2 5/6 2 /6 2 /6 LF 2.9 3 2.3 3 2.59 4 /4 2.59 4 /4 P 2.4 2.48 SN 2 /4 2 2 2 ZB 5 /8 5 /4 6 5/64 6 5/64 P 2 M2 2 S 76 85 95 P95 NM N 2-6-5-25
Series N 25 Oversized od-foot Style: NL (XB5) Z + Stroke X + Stroke 2- (NPTF) B MM T H B S 6-B (Hole) O L F S + Stroke L O Bore size (in) MM 2 (2") B H -6 /8 2.6 2 /6 7/6 L O T 9/6 /8 B B D DD F S P LF S X Z /2 /8 /2 7/8 5/6-24 2 /2.3.26.6 2.9 2.4 3 6 6 6 9/6 25 (2.5") -6 /8 3. 3 /8 9/6 /8 /2 /8 /2 7/8 5/6-24 3.3.6 2 /4 2.3 2.48 3 6 /8 6 /8 6 /6 325 (3.25") -4 3.9 /2 3 3/6 5/6 /4 /64 2 /2 /4-24 3 /2.57.8 2 2.59 4 /4 7 7 /8 7 7/8 4 (4") -4 4.7 /2 4 /2 2 /4 /4 5/64 2 /2 /4-24 4 /2 /2.57.8 3 /2 2.59 4 /4 7 7 /8 7 7/8 Oversized od-od Side Flange Style: NF (XB5) 4-øFB (Hole) 2- (NPTF) ømm TF UF W F ZB + Stroke Bore size (in) MM B B D DD F FB TF UF W LF P ZB 2 (2") -6 /8 2.6 /2 /8 /2 7/8 5/6-24 2.5.3.26.6.84 3 4 /8 3 2.9 2.4 5 /8 25 (2.5") -6 /8 3. /2 /8 /2 7/8 5/6-24 3.3.6 2.9 3 7/8 4 3 2.3 2.48 5 /4 325 (3.25") -4 3.9 2 /2 /4-24 3.25 /2 7/6.57.8 2.76 4 /6 5 /2 4 /4 2.59 6 5/64 4 (4") -4 4.7 2 /2 /4-24 4.5 /2 7/6.57.8 3.32 5 7/6 6 /4 4 /4 2.59 6 5/64 6-5-26
Series N 26 Oversized od-head Side Flange Style N (XB5) 2- (NPTF) 4-øFB (Hole) ømm Bore size (in) MM B B D DD F F TF UF P XF ZF 2 (2") -6 /8 2.6 /2 /8 /2 7/8 5/6-24 2.5.3.26.6.84 3 4 /8 2.9 2.4 5 5 25 (2.5") -6 /8 3. /2 /8 /2 7/8 5/6-24 3.3.6 2.9 3 7/8 4 2.3 2.48 5 /8 5 /2 325 (3.25") -4 3.9 2 /2 /4-24 3.75 /2.57.8 2.76 4 /6 5 /2 2.59 5 7/8 6 /2 4 (4") -4 4.7 2 /2 /4-24 4.5 /2.57.8 3.32 5 7/6 6 /4 2.59 5 7/8 6 /2 Oversized od-enter Trunnion Style: NT (XB5) UV F F UM XF + Stroke ZF + Stroke /32. øtd TL TM TL MM F XI + /2 stroke 2- (NPTF) TF UF TT ZB + Stroke B P 2 M2 2 S 76 85 95 P95 NM N 2- Bore size (in) MM B B D DD F TD. TL TM TT UM UV LF P XI ZB 2 (2") -6 /8 2.6 /2 /8 /2 7/8 5/6-24 2 /2.3.26.6.84 3.8 5 2.56 2.9 3 2.4 3.29 5 /8 25 (2.5") -6 /8 3. /2 /8 /2 7/8 5/6-24 3.3.6 2.9 3 /2.8 5 /2 3.39 2.3 3 2.48 3.37 5 /4 325 (3.25") -4 3.9 2 /2 /4-24 3 /2.57.8 2.76 4 /2.34 6 /2 4.33 2.59 4 /4 3.95 6 5/64 4 (4") -4 4.7 2 /2 /4-24 4 /2 /2.57.8 3.32 5 /4.57 7 /4 5.2 2.59 4 /4 3.99 6 5/64 6-5-27
Series N 27 Oversized od-double Detachable Head Side levis Style: ND (XB5) 2- (NPTF) L ød ømm F XD + Stroke ZD + Stroke F L M W B W Bore size (in) MM B B D W D DD F F L L M XD LF P ZD 2 (2") -6 /8 2.6 /2 /2 /2 /2 7/8 5/6-24 2.5.3.26.6 /2 6 /8 2.9 3 2.4 6 25 (2.5") -6 /8 3. /2 /2 /2 /2 7/8 5/6-24 3.3.6 /2 6 /4 2.3 3 2.48 6 325 (3.25") -4 3.9 2 /4 /4-24 3.75 /2.57.8 /4 7 2.59 4 /4 8 /2 4 (4") -4 4.7 2 /4 /4-24 4.5 /2.57.8 /4 7 2.59 4 /4 8 /2 Oversized od-double Single Detachable Head Side levis Style: N (XB5) 2- (NPTF) L ømm ød F XD + Stroke ZD + Stroke F L M B Bore size (in) MM B B D D DD F F L L M XD LF P ZD 2 (2") -6 /8 2.6 /2 /2 /2 7/8 5/6-24 2.5.3.26.6 /2 6 /8 2.9 3 2.4 6 25 (2.5") -6 /8 3. /2 /2 /2 7/8 5/6-24 3.3.6 /2 6 /4 2.3 3 2.48 6 325 (3.25") -4 3.9 2 /4 /4-24 3.75 /2.57.8 /4 7 2.59 4 /4 8 /2 4 (4") -4 4.7 2 /4 /4-24 4.5 /2.57.8 /4 7 2.59 4 /4 8 /2 6-5-28
Series N 28 djustable Strokextended The extended stroke stop position is infinately adjustable within the adjustment range. uto switch capable. Dimensions 4-NT Depth ND Specifications Bore size (inch) Fluid Max. operating pressure Min. operating pressure mbient & fluid temperature Piston speed ushion Mounting Standard Stroke Bore size (in).5 2, 2.5 3.25, 4 LD + Stroke 2- (NPTF) SN + Stroke.5 2 2.5 3.25 4 ir 25 psi (.75 MPa) 8 psi (.6 MPa) 4 to 4 F (5 to 6 ) 2 to 2 inch/sec (5 to 5 mm/sec) ir cushion standard Basic style, Foot style, Flange style, enter trunnion style, Side tapped style Standard stroke, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28 How to Order N D B 5 4 uto switch ZZ + 2 stroke + djustable range (: ", B: 2") Mounting Bore size Stroke Stroke djustment range : to " B: to 2" d + Stroke + djustable range X8 djustable strokextend c + djustable range P 2 M2 2 S 76 85 95 P95 NM N 2- Bore size (in) MM B D DD K LD P ZZ 5 (.5") 7/6-2 2.2 /8 9/6 /4-28 2.3.26 9/32.43.7 3.78 2.36 6.97 2 (2") 7/6-2 2.6 /8 9/6 5/6-24 2 /2.3.26 /32.84.7 3.82 2.4 7. 25 (2.5") 7/6-2 3. /8 9/6 5/6-24 3.3 /32 2.9.75 3.98 2.48 7.7 325 (3.25") -6 /8 3.9 /2 /2 7/8-24 3 /2.57 27/64 2.76 2.34 4.64 9.38 4 (4") -6 /8 4.7 /2 /2 7/8-24 4 /2 /2.57 27/64 3.32 2.34 4.64 9.38 Bore size (in) b c d SN NT ND TN XT 5 (.5") /2.25.8 2 /4 /4-2 9/32 5/6 2 (2") 2/32.64 2.9 2 /4 5/6-8 7/6 7/8 5/6 25 (2.5") 2/32.64 2.9 2-6 9/32 /4 5/6 325 (3.25") 2 9/32 2.48 3.37 2 /2-3 /2 2 7/6 4 (4") 2 9/32 2.48 3.37 2 /2-3 2 /6 2 7/6 6-5-29
Series N 29 djustable Strokeeturn Specifications Bore size (inch) Fluid Max. operating pressure Min. operating pressure mbient & fluid temperature Piston speed ushion Mounting.5 2 2.5 3.25 4 ir 25 psi (.75 MPa) 8 psi (.6 MPa) 4 to 4 F (5 to 6 ) 2 to 2 inch/sec (5 to 5 mm/sec) ir cushion standard Basic style, Foot style, Flange style, enter trunnion style, Side tapped style The return stroke stop position is infinitely adjustable within the adjustment range. uto switch capable. Standard Stroke Bore size (in).5 2, 2.5 3.25, 4 Standard stroke, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28 How to Order N D B 5 4 X9 Dimensions uto switch Mounting Bore size djustment range : to " B: to 2" Stroke djustable Strokeeturn (2) (NPTF) 4-NT Depth ND SN + Stroke ZZ + Stroke + djustable range d + djustable range Bore size (in) MM B D DD K LF P ZZ TN XT SN d mm 5 (.5") 7/6-2 2.2 /8 9/6 /4-28 2.3.26. /32 9/32.43.7 3 2.36 6.44 5/6 2 /4.8 M6x.5 2 (2") 7/6-2 2.6 /8 9/6 5/6-24 2 /2.3.26.6 /32 /32.84.7 3 2.4 6.44 7/8 5/6 2 /4.8 M6x.5 25 (2.5") 7/6-2 3. /8 9/6 5/6-24 3.3.6 /32 /32 2.9.75 3 2.48 6.44 /4 5/6 2.69 M6x.5 325 (3.25") -6 /8 3.9 /2 /2 7/8-24 3 /2.57. 27/64 2.76 2.34 4 /4 8.2 /2 2 7/6 2 2.4 M24x.5 4 (4") -6 /8 4.7 /2 /2 7/8-24 4 /2 /2.57. 27/64 3.32 2.34 4 /4 8.2 2 /6 2 7/6 2 2.4 M24x.5 Bore size (in) NT ND 5 (.5") /4-2 9/32 2 (2") 5/6-8 7/6 25 (2.5") -6 9/32 325 (3.25") /2-3 4 (4") /2-3 6-5-3
Series N 3 Dual OperationDouble od 4 positions available from a single cylinder uto switch capable Dimensions 4-NT Depth ND Specifications Bore size (inch) Fluid Max. operating pressure Min. operating pressure mbient & fluid temperature Piston speed ushion Mounting Standard Stroke Bore size (in).5 2, 2.5 3.25, 4 N D B 5 4 N uto switch Bore size Mounting Stroke P + stroke 4- (NPTF) Stroke.5 2 2.5 3.25 4 ir 25 psi (.75 MPa) 8 psi (.6 MPa) 4 to 4 F (5 to 6 ) 2 to 2 inch/sec (5 to 5 mm/sec) ir cushion standard Basic style, Foot style, Flange style, Side tapped style Standard stroke, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28 Stroke B SN + Stroke ( + B) LD + Stroke ( + B) ZZ + Stroke ( + B) How to Order P + stroke B 2 X Stroke B ushion Both ends N W/o cushions H Head end od end Dual operation - Double rod P 2 M2 2 S 76 85 95 P95 NM N 2- Bore size (in) MM B D DD K LD P P ZZ SN 5 (.5") 7/6-2 2.2 /8 9/6 /4-28 2.3.26 9/32.43.7 7.44 2.36.3 9.44 5.56 2 (2") 7/6-2 2.6 /8 9/6 5/6-24 2 /2.3.26 /32.84.7 7.52 2.4.3 9.52 5.64 25 (2.5") 7/6-2 3. /8 9/6 5/6-24 3.3 /32 2.9.75 7.76 2.48.3 9.76 5.88 325 (3.25") -6 /8 3.9 /2 /2 7/8-24 3 /2.57 27/64 2.76 2.34 8.94.57.69 6.82 4 (4") -6 /8 4.7 /2 /2 7/8-24 4 /2 /2.57 27/64 3.32 2.34 8.94.57.69 6.82 Bore size (in) TN XT NT ND 5 (.5") 5/6 /4-2 9/32 2 (2") 7/8 5/6 5/6-8 7/6 25 (2.5") /4 5/6-6 9/32 325 (3.25") /2 2 7/6 /2-3 4 (4") 2 /6 2 7/6 /2-3 6-5-3
Series N 3 Dual OperationSingle od 3 positions can be obtained from a single cylinder. Twice the force is available for the extended stroke. uto switch capable Specifications Bore size (inch) Fluid Max. operating pressure Min. operating pressure mbient & fluid temperature Piston speed ushion Mounting Standard Stroke Bore size (in).5 2, 2.5 3.25, 4.5 2 2.5 3.25 44 ir 25 psi (.75 MPa) 8 psi (.6 MPa) 4 to 4 F (5 to 6 ) 2 to 2 inch/sec (5 to 5 mm/sec) ir cushion standard Basic style, Foot style, Flange style, levis style, Side tapped style Standard stroke, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28 xample: NDB5-2+3 will stroke 2" then an additional 3" for a total stroke of 5". The front cylinder B (rod end) must be equal to 5" to allow the full stroke. How to Order N D B 5 4 + 2 H X Dimensions uto switch Bore size Mounting Stroke Stroke B- Dual operation- Single rod ushion Both ends N W/o cushions H Head end od end P + Stroke B 4- (NPTF) PB + Stroke 4-NT Depth ND Stroke B Stroke SN + Stroke + Stroke B + Stroke B ZB + Stroke + Stroke B Bore size (in) MM B B D DD TN XT LF P PB P 5 (.5") 7/6-2 2.2 /8 /8 9/6 /4-28 2.3.26..43 5/6.7 7.26 2.36 2.4.24 2 (2") 7/6-2 2.6 /8 /8 9/6 5/6-24 2.5.3.26.6.84 7/8 5/6.7 7.26 2.4 2.44.2 25 (2.5") 7/6-2 3. /8 /8 9/6 5/6-24 3.3.6 2.9 /4 5/6 /75 7.38 2.48 2.52.2 325 (3.25") -6 /8 3.9 /2 /2 /2 7/8-24 3.75 /2.57.8 2.76 /2 2 7/6 2.34 8.52 2.76.5 4 (4") -6 /8 4.7 /2 /2 /2 7/8-24 4.5 /2.57.8 3.32 2 /6 2 7/6 2.34 8.52 2.76.5 Bore size (in) SN ZB NT ND 5 (.5") 5.89 8.39 /4-2 9/32 2 (2") 5.89 8.39 5/6-8 7/6 25 (2.5") 6. 8.5-6 9/32 325 (3.25") 6.89. /2-3 4 (4") 6.89. /2-3 6-5-32
Series N 32 Fluoro ubber Seals Material for seals is changed to fluoro rubber excellent in chemical resistance. With oil Scraper Scraper removes frost, weld spatter, cutting dust, and etc., and it protects the seals. Specifications Bore size (inch) Fluid Max. operating pressure Min. operating pressure od material mbient & fluid temperature Piston speed ushion Mounting Standard Stroke Bore size (in).5 2, 2.5 3.25, 4 Specifications.5 2 2.5 3.25 4 ir 25 psi (.75 MPa) 8 psi (.6 MPa) Stainless steel 34 4 to 4 F (5 to 6 ) 2 to 2 inch/sec (5 to 5 mm/sec) ir cushion standard Basic style, Foot style, Flange style enter trunnion style, Side tapped style, levis style od side trunnion style, Head side trunnion style Side lug style Standard stroke, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28 How to Order N D Mounting Bore Stroke Suffix X22 x: NDB 5-422 uto switch capable Bore size (inch) Fluid Max. operating pressure Min. operating pressure mbient & fluid temperature Scraper Piston speed ushion Mounting Standard Stroke Bore size (in).5 2, 2.5 3.25, 4 Fluoro rubber seals.5 2 2.5 3.25 4 ir 25 psi (.75 MPa) 8 psi (.6 MPa) 4 to 4 F (5 to 6 ) oil scraper (Metal).4 to 2 inch/sec ( to 5 mm/sec) ir cushion standard Basic style, Foot style, Flange style enter trunnion style, Side tapped style, levis style od side trunnion style, Head side trunnion style Side lug style Standard stroke, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 2, 3, 4, 5, 6, 8,, 2, 4, 6, 8, 2, 24, 28 P 2 M2 2 S 76 85 95 P95 NM N 2- How to Order N D Mounting Bore Stroke X35 x: NDB 5-435 uto switch capable With coil scraper 6-5-33
D dia. Series N 33 ccessory Bracket Dimensions ye Bracket Part no. B D DD F FL L M M N-P5 /2 3/32 2 /2 /8 /2 9/6.63 N-P325 /4 7/32 3 /2 7/8 /4 7/8 2.56 DD dia. levis Bracket Part no. B B D W DD F FL L M M N-B5 2.3.785 /2 /2-24 2 /2 /8 /2 /2 9/6 N-B325 3.6 2 9/6.265 /2-2 3 /2 7/8 /6 /6 DD dia. od levis Part no. B D H W F L N-5.765.5 /2 /2 7/6-2 /2 N-325.265.75 2 /4 /4 /8-6 D dia. D dia. Order to Match od Thread od ye Pivot Pin Pivot Pin Part no. B D NI-5 /2 /2 7/6 2 NI-325 /8 2 /6 /4 7/8-6 Part no. D L N-5 /2 7/8 N-325 2 Tap through Part no. D D 2 L P NDP-5.5-.2.6 2.28.94 NDP-325.75-.2.4 3. Note) otter pins are included. 2 x D D dia. Note) otter pins are included. 6-5-34
Series N 34 uto Switch Specifications How to Order uto Switches rommet type D - onnector type D - P For standard part number please refer to applicable auto switches on page 6-5-7. Lead wire color 2 pin 3 pin Brown Orange Lead wire length S.5 (m)(.64 ft) M. (m)(3.28 ft) onnector type M8-3 pins B M8-4 pins D M2-4 pins onnector type M8-3 pin M8-4 pin M2-4 pin Sensor type D 2-wire D 2-wire non-polar D 3-wire D 4-wire Lead wire length.5 (m) (.64 ft) L 3 (m) (9.84 ft) Z 5 (m) (6.4 ft) uto Switch Mounting Bracket Part No. Bore size (in) Model no. 5, F5 6, 5 5 (.5") 2 (2") 25 (2.5") 325 (3/25") 4 (4") NBT-5 NBT-2 NBT-2 NBT-325 NBT-325 Pin arrangement pplicable standards Impact resistant IP degress of protection Insulation resistance Withstand voltage pin Brown Brown Brown onnector M8-3 pin/4 pin 4 3 Blue Blue 4 pin Blue Blue Black Black For standard part number please refer to applicable auto switches on page 6-5-7. pin OUT (+) D (+) D (+) 2 3 IS 4524, IS 4525, I 947-5-2, N 42 3 m/s 2 IP-67 (I529 standard) MΩ or more at 5 VD meg. 5 V minute (between contacts), Leakage current m or less Meaning of contact no. 2 pin 3 pin Diagnostic output 4 4 pin OUT ( ) OUT (±) OUT ( ) D ( ) OUT D ( ) OUT ± 2 3 4 Unit : mm ( ) : ft P 2 M2 2 S 76 85 95 P95 NM N 2- Sensor M2-4 pin Lead wire length 3.4 (.) ø (.3) Sensor Lead wire length 44 (.4) ø4 (.5) 6-5-35