13 Chassis
95039 Santee Low Glide Stock Replacement Frame Stock-style frame kit accepts most Original Equipment or aftermarket accessories, with brackets and tabs for the coil, belt guard, late 87-99 rear brake caliper and master cylinder, flatside gas tanks, oil tank, shock absorbers and 86-99 fender struts. There is also a mounting loop provided on the right front downtube for 87-91 oil filter housings. Everything bolts in place like on stock frames. Frames have 1"-diameter 1020 mild steel tubing with a stock 32 rake, no stretch, and the swingarm is stock width with clearance for belt or chain drive. The steering head uses stock bearings and cups. With correct inner and outer primaries and transmission mounting plate, 4-speed, 5-speed or 6-speed transmissions can be installed. Include rear axle and swingarm pivot shaft with bearings. 95039 Low Glide Stock Frame and Swingarm.............. $1,002.95 Replacement and Accessories for Low Glide Frames Here are some items to finish a hot custom bike. 95044 Swingarm pivot bearing and retaining clip for all Softail models from 84-99 (repl. OEM 9076).................. $19.99 17289 1/4"-offset driveline offset kit (permits the use of a 1/2"- wider rear tire)...................................... $89.99 Replacement and Accessories for Low Glide Frames Bearings and Cups 12263 Chrome bearing cups (pair)........................... $25.99 12264 Timken bearing (sold each)............................ $9.99 Flatside Gas Tanks 15298 5 gallon............................................ $205.99 15294 6 gallon............................................ $184.99 25550 Gas tank mounting kit............................... $49.99 13 Santee 4-Speed Rigid Frames These Classic Santee frames are the perfect start to any Old School build. Available with the classic look of either Wishbone or Straight Leg style downtubes that Santee is known for. Frames accept any Big Twin engine except Twin Cam (including Strokers and Evolution motors). Frames are set-up for disc brakes and include rear axle kit. Straight Leg Frames 650195 30º rake, 0" downtube stretch, 0" backbone stretch WITHOUT tank mounts...................................... $1,144.99 Wishbone Frames 650201 30º rake, 0" downtube stretch, 0" backbone stretch WITHOUT tank mounts....................................... $1,199.99 Replacement Axle Kit 650241 Replacement axle for Santee 4-speed rigid frames......$124.99 650195 13.02 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL 651235 SEATS & BAGS FOOT HAND LIGHTING 651233 ELECTRICAL Santee Rigid Frames for Sportster Models Designed and available to fit all Sportster engines from 57-03, these frames have a stock width rear section that will accept a 130mm rear tire with a standard 1 1/8 final belt or chain. Made in the U.S.A. 651233 30 rake, 0 Backbone, 0 downtube stretch rigid frame for 57-76 XL models without tank mounts........................................ $1,069.99 651234 30 rake, 0 Backbone, 0 downtube stretch rigid frame for 77-85 XL models without tank mounts........................................ $1,069.99 651235 30 rake, 0 Backbone, 0 downtube stretch rigid frame for 86-03 XL models without tank mounts........................................ $1,069.99 EXHAUST INTAKE ENGINE 651234 GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES SHEETMETAL Oil Tanks for XL Rigid Frames by Paughco This oil tank is for use with rigid Sportster frames manufactured by Paughco. Drain plug sold separately. Made in USA by Paughco. 632247 Oil tank for use w/paughco XL rigid frames....................................... $196.99 632248 Oil tank drain plug....................... $10.99 Santee Rigid Frame for 04-Up Rubber Mounted Sportsters This frame was designed to run a 04-Up rubber mounted Sportster engine and will hold up to a 150mm rear tire with a belt or chain final drive. Made in the U.S.A. 651237 30 rake, 0 Backbone, 0 downtube stretch rigid frame without tank mounts for 04-Up rubber mounted XL engines................. $1,498.95 INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.03
604157 604155 Custom FXR-Style Frames for Touring Model Drivelines by Paughco These custom frames are designed to accept all 93-2011 Evo or Twin Cam Touring model drivelines with the oil tank located under the transmission. They equipped with FXR-style mounts for the gas tank, side covers, seat and battery (components sold separately). They also include a special sheetmetal plate that covers the area where the oil tank would normally reside. These frames are offered in either a stock or wide 180/200 tire version and are configured for forward controls and have a 3-point mount on the left-side that will accept a forward shifter bracket and conventional kickstand mounting bracket. Frame, swingarm and components are sold separately. Made in the U.S.A. Frames 604155 Stock-style FXR frame ONLY for Touring driveline........$1,766.99 604156 Wide 180/200mm FXR frame ONLY for Touring driveline.$1,766.99 Swingarms & Components Pivot shafts & rear axles sold separately 604157 Stock-style swingarm ONLY, raw steel.................... $351.99 604158 Wide 180/200mm swingarm ONLY, raw steel............. $434.99 604159 Stock length rear axle kit for #604157..................... $88.99 604160 Wide length rear axle kit for #604157.................... $135.99 Paughco FXR/FLT Pivot Shaft and Isolator Bushings Rebuild your swingarm with these key parts. They are a perfect reproductions of the originals. Sold each. 651437 Rubber isolator mount for 80-up Touring and FXR models (OEM 47564-86B, sold each........................... $31.99 651434 Swingarm pivot shaft for 1980-2001 Touring and FXR models (OEM 47492-89A).................................... $69.99 Paughco Heavy Duty Front Motor Mount Made from heavy-duty polyurethane, this mount helps to reduce the amount of vibration in the drivetrain. Kit includes chrome mounting block and a 2-pc bushing with internal spacer tube. Fits all FXR and Touring models from 80-09. 651436 Front motor mount for all 80-08 FXR and Touring models.....................................................$75.95 13 Swingarm Pivot Blocks by Paughco CNC-Machined from 6061 billet aluminum, these swingarm pivot blocks are available in chrome or black. They fit all 82-00 FXR models as well as most custom rubber mount frames. Sold in pairs. 604161 Chrome pivot blocks.................................$109.99 604162 Black pivot blocks....................................$109.99 Paughco FXR/FLT Swingarm Upgrade Kit Specifically designed to upgrade the quality and feel of the driveline on your FXR or Touring model bike. These 7-pcs convert the old style OEM parts to a high-tech spherical bearings with CNC-Machined precision spacers and collars. Made in the U.S.A. 651435 7-pc swingarm upgrade kit for 80-01 FXR & Touring models...................................................... $339.99 13.04 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL SEATS & BAGS FOOT Chrome Swingarm Axle Covers Cover up the ugly cluttered axle adjusters and axle nut with these show chromed covers. They come with all required hardware. Will not work on models with stock saddlebags. 688197 Swingarm Axel covers 86-07 Softail except FLSTS..................................$79.99 Chrome Rear Frame Covers for Softail Models Dress up the rear section of your Softail. Made of chrome plastic installs in minutes with silicone adhesive included. Fits all Softail models except Fat Boy and FLSTN models 86-99 (sold in pairs). 78054 Chrome Rear Frame Covers for Softail Models............ $48.99 HAND LIGHTING ELECTRICAL EXHAUST INTAKE 95044 Swingarm Pivot Components Manufactured from high-quality materials for all factory and aftermarket swingarms. Sold each. For Softail Models from 86-99 95044 Swingarm pivot bearing and retaining clip for all Softail models from 84-99 (repl. OEM 9076)..$19.99 84379 Chrome sockethead pivot bolt set (repl. OEM 4961).............$25.99 Swingarm Bumpers For stock replacement or custom applications. Replaces OEM 11451, and fit all Softail models from 85-99. Original Equipment Bumpers These are Original Equipment parts. 75190 Pack of 10....................$4.30 75191 Sold each....................$5.99 Aftermarket Bumpers 695002 Sold each....................$4.99 Chrome Swingarm Pivot Bolt Covers for Softail Models These covers are held in place with set screws and look great when installed in conjunction with CC #28266 chrome rear frame covers. They fit all Softail models from 84-07 (except Fat Boy and FLSTN models). Sold in pairs. 14317 Pivot bolt cover for Softails 84-99......................... $10.99 688179 Pivot bolt cover for Softails 00-07......................... $24.99 ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES SHEETMETAL Chrome Swingarm Pivot Bolts for Softail Models Chrome hex head swingarm pivot bolts. Grade 8 bolts measure 3/4"-16 x 3"-long. Fit Softail models from 84-99. Sold in pairs. 84378 Swingarm Pivot Bolt Spacers..$19.49 Swingarm Pivot Bolt Spacers for Softail Models Fit Softail models from 87-99. Pack of 10. 84602 Swingarm Pivot Bolt Spacers...$2.50 Chrome Pivot Bolt Cover for Late Sportster Models Fits over the exposed head of the swingarm pivot bolt on all Sportster models from 82-03. It features chromeplated die-cast construction and is held firmly in place by a sockethead screw. Sold each. 14318 Chrome Pivot Bolt Cover.... $8.99 INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.05
Black 3-Piece Frame Clamps These black versions of our trusted three piece frame clamps make attaching anything from lighting to pegs to your frame or crash bar an easy task. Sold each, in two different sizes. 688854 Frame clamp 1-1/8 black...............................$8.99 688855 Frame clamp 1-1/4 black...............................$8.99 FXSTD Deuce 180mm Fat Tire Kit by Vulcan Engineering This simple kit allows you to run a 180mm tire on your 00-07 Deuce with no modifications to the frame or wheel. Kit includes a pulley spacer and alignment spindle. Easy install that can be done at your next rear tire change! 668253 180 mm tire conversion for 00-07 FXSTD Deuce models...$69.99 3-Piece Frame Clamps Chrome-plated, 3-piece design eliminates spreading the clamp to fit over frames. Sold each. 11235 1" clamp 3-piece.......................................$9.99 11237 1 1/8" clamp 3-piece....................................$9.99 11236 1 1/4" clamp 3-piece....................................$9.99 13 Steering Damper Kits Complete kits for Softail and Sportster models. Includes a hi-tech adjustable steering dampener and all mounting hardware for a clean and quick installation. Improves the stability of the front end and provides more riding comfort. 84609 Fits FX Softail models (except Springer models) from 84-99........................................................................ $189.99 688571 Fits FX Softail models (except Springer models) from 00-10........................................................................ $199.99 688570 Fits FXD Dyna models (except FXDWG) from 06-14................................................................................ $199.99 688572 Fits FXD Dyna models (except FXDWG) from 91-05................................................................................ $199.99 688573 Fits FXDWG models from 93-05................................................................................................. $209.99 682646 Fits Sportster models (exept models with 4.5 gallon tanks) from 07-14.............................................................. $199.99 688574 Fits Sportster models (exept models with 4.5 gallon tanks) from 04-06.............................................................. $199.99 84610 Fits Sportster models with 39 mm forks from 87-03............................................................................... $169.99 13.06 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL SEATS & BAGS 680028 FOOT HAND 668100 LIGHTING ELECTRICAL The Touring Link by Progressive Suspension Finally an inexpensive and easy to install solution to the handling challenges faced by most Touring models. The brace does not hang below the frame so it will not cut into your ground clearance. Helps keep motor and swingarm assembly aligned with chassis without introducing unnecessary vibration to the rider. 680037 Fits 93-08 Touring models.............................$199.99 680028 Fits 09-13 Touring models.............................$229.99 668101 EXHAUST INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE RevTech Chassis Stabilizer Looking for a way to stop the wobbling, weaving, and rear steering on your Touring model? The RevTech Chassis Stabilizer utilizes a swingarm pivot anchor to cure these problems. So you can feel confident leaning your Bagger into the corners with a RevTech Chassis Stabilizer under your Bagger. Fits FLH/FLT models 93-08. 668100 Satin Finish....................................... $399.99 668101 Black Anodized Finish............................. $414.99 WHEELS TIRES & BRAKES SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.07
610370 Highway Bar with Footrest This highway bar & footrest combination was designed with the riders comfort in mind. They are constructed of 1.25 steel tubing and chrome-plated with the addition of a heavy-duty rubber foot pad. They are perfect for those long rides when you want to stretch your legs while on the road. 610370 Fits 09-Up Touring models (except FLTR)........................... $199.99 610369 Fits 97-08 Touring models (except Road Glide)...................... $199.99 610368 Fits 00-Up FLST Softail models..................................... $206.99 610367 Fits 86-99 FLST Softail models..................................... $199.99 31607 13 Santee Designer Series Bonanza Highway Bar by Fred Kodlin This is the latest from Fred Kodlin and the Murder Cycles crew. These highway bars are the perfect match to the Bonanza handlebar series. The Highway Bars feature 1 1/4 steel tubing with built-in peg mounts so there is no need for those bulky clamps. They are available in a chrome-plated or black powdercoated finish. Chrome 697174 Bonanza highway bar for 09-Up Touring models (except FLTR Road Glide models), chrome................................ $259.99 697168 Bonanza highway bar for 97-08 Touring models (except FLTR Road Glide models), chrome............................... $259.99 Black 697175 Bonanza highway bar for 09-Up Touring models (except FLTR Road Glide models), black....................................... $249.99 697169 Bonanza highway bar for 97-08 Touring models (except FLTR Road Glide models), black... $249.99 Optional Footpeg Clevises (required if you want to run highway pegs) 652025 Chrome 3/8-20 clevis, sold in pairs....... $19.99 652026 Black 3/8-20 clevis, sold in pairs.......... $19.99 Note: Not for use with factory lowered (FLHX, FLHRS) and aftermarket lowered bikes. Khrome Werks Chrome Highway Bars for Softail Models Heavy gauge, 1"-diameter steel tubing for that classic 50's look. Front bar kit includes a special oil cooler relocation bracket. All necessary mounting hardware is included. Made in the USA. 31607 Front highway bar for FL Softail models from 86-99................ $165.99 31416 Rear highway bar for all FL Softail models from 86-13 (except FLSTF, 90-99 FLSTC 93-96, FLSTN models). Also works well in conjunction with our Khrome Werks Trailer Hitch for Softail models from 86-13 (CC#31414)................................................................ $185.99 Warning: These highway bars are for cosmetic use only and will not provide leg or vehicle protection in the event of a low speed fall. They are not made nor intended to provide protection from bodily injury in a collision with an automobile or any other object. Note: 90-99 FLSTC models require the installation of CC #28927 Bracket Kit to replace the Original Equipment brackets which attach the saddlebag support frame to the footpeg bolt. Additionally, neither of CC s chrome toolbox kits may be installed because of contact with the saddlebag support frame. 13.08 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL 28928 28929 642911 SEATS & BAGS FOOT 28933 28932 642907 HAND LIGHTING 28934 28930 642898 ELECTRICAL EXHAUST 642900 INTAKE 28935 Chrome Highway Bars American-made reproductions of Original Equipment bars have flawless chrome-plating and are made from high-strength tubing with heavy-duty 1-1/4" steel plate mounts welded to the tubing to insure a perfect fit. Front 1-1/4"-Diameter Highway Bars 609620 Fits FL Softail models from 00-Up......................$248.99 28933 Fits FL Softail models from 86-99 (repl. OEM 49004-90)..$248.99 609621 Fits FX Softail models from 00-Up.....................$248.99 28932 Fits FX Softail models from 84-99 and 4-speed FX models from 72-86 (repl. OEM 49016-72D)..........................$248.99 609622 Fits Dyna Wide Glide models from 93-05...............$248.99 609623 Fits all Dyna Glide models (except Dyna Wide Glide models) from 91-05..........................................$248.99 609630 Fits all XL models from late 04-Up, chrome.............$248.99 609624 Fits all Sportster models from late 84-03...............$248.99 28935 Fits Touring models from 88-96 (repl. OEM 49184-88)...$248.99 28929 Fits 4-speed FL models from late 79-84 (repl. OEM 49040-79)....................................................$248.99 28928 Fits 4-speed FL models with swingarm frames from 58-E79 (repl. OEM 49038-58B)...............................$248.99 Rear Highway Bars 28930 Fits 4-speed chain drive FL models from late 67-84 (repl. OEM 49137-67B) 7/8" tubing...............................$248.99 28934 Fits Softail models from 86-99 (except 90-99 FL Softail models) repl. OEM 49158-89B (1" tubing)......................$248.99 Warning: These reproduction Highway Bars are for cosmetic use only and will not provide leg or vehicle protection in the event of a low-speed fall. They are not made nor intended to provide protection from bodily injury in a collision with an automobile or any other object. Highway Bars Reproductions of the Original Equipment bars constructed from 1-1/4 steel tubing and available in either a chrome-plated or gloss black powder coated finish. Hardware included. Chrome 642897 Fits 09-Up Touring models, chrome................. $174.99 642899 Fits 97-08 Touring models, chrome.................. $174.99 642911 Fits 00-Up FLST Softail models, chrome.............. $168.99 642907 Fits 86-99 FLST Softail models, chrome.............. $177.99 Black 642898 Fits 09-Up Touring models, black................... $168.99 642900 Fits 97-08 Touring models, black.................... $168.99 642912 Fits 00-Up FLST Softail models, black................ $165.99 642908 Fits 86-99 FLST Softail models, black................ $168.99 AVAILABLE IN CHROME Retro Styled Highway Bars for Softail Models Retro styling for that nostalgic look! These curved bars add that classic vintage style to your bike. Constructed from 1-1/4 steel tubing and available in either a chrome-plated or gloss black powder coated finish. Hardware included. Chrome 642903 Fits 00-Up FLST Softail models, chrome.............. $174.99 Black 642904 Fits 00-Up FLST Softail models, black................ $168.99 ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.09
688174 631098 688173 Kickstands for Late Softail Models Stock length replacement kickstands for 07up Softail models, available in black or chrome finish. 688173 Kickstand for 07-Up Softail models, chrome.....................$59.99 688174 Kickstand for 07-Up Softail models, black.......................$59.99 Ness 1 Lowered Kickstands A must when lowering your bike Available for both Touring and Softail models Chrome-plated forged steel 631098 Fits 84-06 Softail models......$79.99 631100 Fits 07-Up Softail models.....$79.99 631099 Fits 07-Up Touring models....$79.99 15212 Chrome Kickstand Kits for Softail Models Complete chrome kickstand kits are available in 1" or 2" under stock length for lowered bikes. Include all necessary hardware. Fit all Softail models from 89-99 15211 Stock Length................$70.99 15212-1" under stock length.......$69.99 600690-2" under stock length, stand only............................$71.75 16003 Chrome Weld-On Kickstand by TC Bros Get rid of your ugly stock kickstand and replace it with TC Bros. Choppers super clean chrome kickstand with hidden spring. Kit includes chrome kickstand and weldable mild steel block coped to fit 1 1/8 tubing on your frame. 660913 Weld-on hidden spring kickstand............................$74.99 Chrome Kickstand for Lowered Dyna Glide Models Chrome kickstand is available 1" under stock length for lowered bikes. Fits Dyna Glide models from 91-Up except Dyna Glide Convertible models. 16002 Stock length kickstand.......$50.99 16003-1" under stock kickstand.....$73.99 15991 688171 Chrome Kickstands for Sportster Models Available in a stock length or -1 for lowered bikes. Fits Sportster models from 04-14. 610412 Stock length kickstand.......$42.99 610411-1 under stock length kickstand............................$42.99 688171 Kickstand clevis pin fits XL models 89-14........................$9.99 13 Ness Hidden Spring Kickstand Kits The ultimate in custom kickstands for your lowered application Features internal spring loaded ball bearing lock for a cleaner look and optimum functionality The telescopic chrome kickstands are adjustable in height by 1 inch Mounting brackets are machined from polished stainless steel to eliminate chrome wear in high contact areas All of these kits feature a hidden ball bearing design return spring for positive stock feel and retaining clean look 631094 Telescopic kickstand for 84-99 Softail, 4-speed Big Twins and custom applications........$199.99 13.10 Original-Style Kickstands Fit 4-speed Big Twin and Softail models from 36-88 15991 Stock length (Repl. OEM 50061-36)............................ $36.99 15992 +1" over stock (fits 4" to 6" over forks)....................... $40.99 15988 Chrome Kickstands for Softail Models Stock-style kickstand arms for Softail models from 89-06. Available in stock length and -1 inch under for lowered bikes. 15988 Stock length.................$51.99 15989-1 inch under for lowered bikes............................$48.99 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. 91991 Softail Kickstand Kits Complete kickstand kits for 89-99 Softail models in either a stock length or +1 inch over stock 91991 Kit with stock-length kickstand............................$64.99 91992 +1 inch over stock-length kickstand kit..........................$79.99 Please see Cautionary Information in back of catalog.
APPAREL 688186 SEATS & BAGS 688185 FOOT Kickstand Wedge Kit for Touring Models Allows the use of the stock kickstand when the bike is lowered, without excess lean. All mounting hardware is included. 688695 Kickstand wedge FLT 84-08............................$39.99 688187 HAND LIGHTING 688188 Kickstand Springs High quality replacement kickstand springs. Sold each. 688185 Fits 91-01 Dyna models (replaces OEM 50057-91)....... $6.99 688186 Fits 99-06 Touring models (replaces OEM 50112-99).... $4.99 688187 Fits FXST 85-06, FXR 91-94, FLT 91-98 and XL 86-09 (replaces OEM 50005-85)..................................... $4.99 688188 Fits 37-84 FL, 84 FXST, 80-90 FLT, 52-83 XL and K-models (replaces OEM 50011-30A)........................... $3.99 688184 Fits 07-Up Softail and Touring models (replaces OEM 49725-07A)............................................... $4.99 ELECTRICAL EXHAUST INTAKE Kickstand wedge Fits 84-99 Softail models. 170140 Kickstand wedge Big Twins............................$13.99 ENGINE GASKETS TRANSMISSION & CLUTCH Kickstand Bumper for Softail Replacement kickstand bumper fits Softail models 89-06. Also used on many one-piece fuel tanks on FX, FXE and XL 73-E84. Sold each. 688640 Replaces OEM 62123-07, each...........................$1.69 Kickstand Stop for Softail and 4-Speed Models This innovative little stop provides one of the first alternatives to letting the kickstand bang into the primary case when returning. Fully-adjustable, it installs on the kickstand shaft and keeps it aligned with the primary but stops the kickstand just short of banging into it. 31461 Fits all 4-speed Big Twins from 58-84 (except FXWG) and Softail models from 89-06.......................... $21.99 DRIVELINE WHEELS TIRES & BRAKES SHEETMETAL INSTRUMENTS & GAUGES Kickstand Bumper for Sportsters Rubber kickstand bumper for Sportster models from 89-12. Sold each. 688645 Kickstand bumper for Sportsters........................$2.49 GENERAL CROSS REFERENCE www.customchrome.com 13.11
SPRINGER Springer Front Ends by DNA These kits accept late model fenders, brakes and wheels with 3/4 -diameter axles. The reinforced top and bottom trees reduce flex and improve handling. They feature TIG welded alloy steel construction for strength and durability, and fit most Big Twins from 49-Up. Kit includes main springs, fork legs, neck, top nut, crown nut, rocker assemblies with brass bushings and top clamp. Available fully chromed, or black with chrome rockers, top clamp and springs. They fit all cast neck Big Twin models from 49-Up with 1 neck bearings (except FXR, Dyna Glide and Touring models), and require the use of risers with 1/2-20 mounting bolts. Available in a variety of styles and finishes. Note: Use the sizing chart below to determine which length would be the best part number for your particular application. Vintage Style Springer s Chrome Front Ends 635068 Stock 22, Vintage chrome............... $699.99 635070-2 under stock, Vintage chrome......... $699.99 635069 +2 over stock, Vintage chrome.......... $699.99 Black and Chrome Front Ends 635071 Stock 22, Vintage black................. $699.99 635073-2 under stock, Vintage black........... $699.99 635072 +2 over stock, Vintage black............ $699.99 Narrow Style Springer s Chrome Front Ends 635062 Stock 22, Narrow chrome............... $699.99 635064-2 under stock, Narrow chrome......... $699.99 635063 +2 over stock, Narrow chrome.......... $699.99 Black and Chrome Front Ends 635065 Stock 22, Narrow black................. $699.99 635067-2 under stock, Narrow black............ $699.99 635066 +2 over stock, Narrow black............ $699.99 Standard Wide Style Springer s Chrome Front Ends 08631 Stock 22, Standard chrome............. $649.99 08630-2 under stock, Standard chrome........ $649.99 08632 +2 over stock, Standard chrome......... $649.99 08631 652112 652113 635074 635065 13 Black and Chrome Front Ends 08636 Stock 22, Standard black................ $649.99 08635-2 under stock, Standard black.......... $649.99 08637 +2 over stock, Standard black........... $649.99 Brake Kit 640746 Springer caliper kit, chrome.............. $428.99 635074 Springer caliper kit, black................ $389.99 Accessories 632970 Chrome fender brackets for -2" to +8" front ends, (3/4 ).................................. $106.99 12643 Chrome 3"-tall handlebar riser set (1/2"-20 mounting bolts)......................... $99.99 160879 Glide-style top clamp with 4 3/4" centerline (includes pinch bolts).................... $159.99 08640 Axle kit with axle, spacers, nuts, and speedometer drive adaptor for 84-99 single flange wheels........................................ $49.99 652112 Rocker, left chrome...................... $56.99 652113 Rocker, right chrome..................... $56.99 635071 Chart Of Springer Sizes and Suggested Applications for Springer Front Ends Springer ForksTo determine the proper Springer fork for your application, please measure the fork currently on your bike and use the chart below. All measurements should be taken from the lower stem bearing cup to the axle center. If Your Stock Front Fork Measures: 19" to 21" you should use the 2" under stock assembly 21" to 23" you should use the Stock 22" assembly 23" to 25" you should use the 2" over stock assembly 25" to 27" you should use the 4" over stock assembly 635068 13.12 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL 28206 SEATS & BAGS FOOT HAND 28205 Springer Fork Lowering Kit by White Bros. The quick and easy way to lower front forks 1 1/2" for a custom look. Includes chrome compression springs, spring spacers and bushings. Requires CC #28206 spring compressor tool for installation. 28205 Fits FXSTS Springer Softail models (except FLSTS models) from 89-05...............................................$149.99 28206 Compressor tool......................................$39.99 652110 652111 LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE Ness-Tech Top Tree for Springer Softail Models Chrome-plated top tree permits the use of conventional handlebar risers or custom T-bars with 3 1/2" centers. 05080 Fits all FXST Springer Softail models from 88-07 (except FLSTS models).............................................$179.99 WHEELS TIRES & BRAKES SHEETMETAL Comfort Shock for DNA Springers Improve the ride of your DNA springer front end with this complete shock mounting kit. Comes with shock and all mounting brackets and hardware. 652110 Springer shock kit chrome......................... $141.99 652111 Springer shock kit black........................... $141.99 INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.13
654140 13 6 Degree Raked Triple Trees for Touring Models by DNA Designed to properly rake your Baggers when running a 21 or 23 front wheel Does not require any frame modifications Designed to fit all 97-13 Touring models Comes in a raw aluminum machined finish 635075 6 degree triple trees for 97-13 Touring models..........$639.99 Early Big Twin Triple Trees Fit all 4-speed Big Twin models from 49-99. Styled after 60-84 triple trees and drilled and tapped for slider covers and early headlight, but with late-style, 4-piece rubber handlebar bushings. 13027 Chrome set......................................... $241.99 13028 Black set........................................... $229.99 13056 Chrome upper clamp only............................ $99.99 13057 Chrome lower clamp only........................... $134.99 13058 Black upper clamp only............................... $85.99 13059 Black lower clamp only.............................. $111.99 Note: The top trees are not drilled and tapped on the backside for headlight tins. Bottom trees have no padlock tab. 13057 and 13059 include stem. Arlen Ness KO Raked Triple Trees for FL, FL1, FL2 Touring Models These 11 or 7 billet triple trees will properly rake your Bagger for the use of 21, 23, & 26 wheels. No cutting, welding, or custom fabrication needed of any kind Extensively road tested, this kit is the best handling raked tree kit available. Attain close to stock handling with large diameter front wheels Designed exclusively for 21, 23, and 26 Diameter wheels, stock diameter wheels will not work with triple tree kit Does not require modification of stock frame. Fairings also maintain stock position and does not require angled headlight wedges or special brackets to properly adjust headlights When using 23 or 26 front wheels on Road Glide models, the optional fairing bracket kit is recommended for increased fairing clearance Designed to fit all 97-13 FLT Touring models (Except Road King) Kit includes black anodized billet aluminum triple trees, steering stem, fork tube extension, fork stops, travel limiters, and all necessary hardware. 11 Triple Tree Kits 654140 11 raked bagger tree kit for all 97-13 FLH/FLT Models..$899.99 654141 FLTR fairing mount kit 09-13..........................$169.99 654142 FLTR fairing mount kit 98-08..........................$169.99 7 Triple Tree Kits 654165 7 raked bagger tree kit for all 2014 FLH/FLT Models....$799.99 654164 7 raked bagger tree kit for all 97-13 FLH/FLT Models...$799.99 654141 FLTR fairing mount kit 09-13..........................$169.99 654142 FLTR fairing mount kit 98-08..........................$169.99 13.14 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL 13040 SEATS & BAGS FOOT HAND LIGHTING Chrome Triple Tree Sets Chrome replacement triple tree sets include upper and lower tree, pinch bolts, and dust cover. Completely interchangeable with Original Equipment trees. 13090 Fits FL Softail models from 84-99, TÜV................. $259.99 13091 Fits FX Softail models from 84-99 and aftermarket cast neck frames, TÜV......................................... $224.99 Components for FL Softail Models Individual upper and lower trees for all models from 86-99 (except FLSTS). 09330 Upper (repl. OEM 45456-86A).......................... $99.99 09331 Lower (repl. OEM 45605-88), TÜV..................... $129.99 Components for FX Softail Models Individual upper and lower trees for FX Softail models from 84-99 and aftermarket cast neck frames (+3 ) 100132 Upper (repl. OEM 345672-80).......................... $97.99 100118 Lower (repl. OEM 45665-80A and 45665-84A).......... $139.99 Custom Chrome Fork Conversion Kits Kits to convert Showa front ends to the look of a Wide Glide front fork without the expense. Kits include: chrome-plated forged triple tree set with lower clamp cover, chrome headlight mount, special chrome fork tube plugs, chrome fork stop, chrome stem nut, chrome axle and axle spacer, and chrome fender spacers to permit the use of the stock fender. The 77-83 Dual Disc kit includes two chrome rotor spacers with hardware; 84-99 kits include one rotor spacer and a chrome hubcap. CC #13203 front fender is recommended for 19" or 21" wheels. 13032 Fits all Sportster and FXR models (except FXLR models) with a single disc and 39 mm forks from 87-99........... $459.99 13040 Fits all dual disc FX models from 77-83 (shown)...... $479.99 ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES SHEETMETAL Chrome Smooth Triple Tree Set Styled after their early FL model counterparts, these custom trees feature late-model rubber handlebar bushings and chrome pinch bolts. The fork slider cover tabs have been removed and the outer edges have been polished to give a smooth, clean look. Includes a lower triple tree cover like the one found on FXWG and Softail models, and it s held in place with your bottom headlight mounting bolt. 13029 Fits all 4-speed Big Twin and Softail models from 49-99, TÜV....................................................$249.99 Smooth Top Chrome Billet Triple Tree Set The ultimate custom triple tree. Sculpted by state-of-the-art CNC-mills from aircraft quality aluminum. These trees not only have a mirror polished chrome finish but also have custom smooth top stem nut system. Head cup bearing tension is adjusted from the bottom for the cleanest top clamp possible. Recessed underside headlight mount. All hardware, stem bolt, handlebar damper, and fork stops are included. 98330 Fits all cast neck frame applications using 41 mm fork tubes from 36-99 (0 rake)............................... $319.99 INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.15
Disc Hub Spacer Kits for Fork Conversion Kits These kits may be purchased as replacement parts for the spacers included in the Custom Chrome fork conversion kits or for use on dual disc models that the kits don t cover. For example on a 90 FXRS Sport Edition with a CC #13032 conversion kit the hub spacer works with the second disc rotor. 13156 Fits conversion kit (CC #13032) for 39 mm Showa forks on models from 87-99 (1 7/16"-thick)......................$34.99 13157 Fits conversion kit (CC #13039) for 35 mm Showa front forks on models from 84-87 (1 11/16"-thick).....................$34.99 13158 Fits conversion kit (CC #13040) for 35 mm Showa front forks on dual disc models from 77-83 (1 5/8"-thick)...............$34.99 Chrome Fork Stem Nut Covers These covers are held in place on the stock stem nuts by a set screw, and fit most 39 mm and 41 mm forks from 80-03. 13009 Fits 39 mm forks on FXR models from 87-00 as well as Sportster models from 88-03 (repl. OEM 48329-90)................$10.99 160110 Fits FXWG and FXST models from 80-99 (repl. OEM 45670-80)......................................................$7.99 Chrome Acorn Stem Nut Functional and good-looking part accents most front forks. 09652 Fits most FL, FXWG, FX Softail and Dyna Wide Glide models. (1" x 24 thread).......................................$11.99 Triple Tree Nut Cover Sets Three-piece kit includes: chrome covers for fork tube caps and triple tree stem nut. Attach with set screws. 160111 Fit Softail and FXWG models from 80-99............... $26.99 13 Chrome Sockethead Pinch Bolt Kit for Big Twins Fits all FL and Wide Glide triple trees (includes FXST). Includes two 7/16-20 x 1 1/4" chrome sockethead bolts and lock washers. 161000 Fits stock style triple trees...............................$4.99 Chrome Fork Stem Nuts Fits all FL, FXWG, FXST and Dyna Wide Glide models from 49-99. 160017 Upper fork stem nut with dust shield. (repl. OEM 48330-48A).....................................................$13.49 Fork Stop Kit for Wide Conversion Kits Fits our custom plate style triple tree and front end sets. 160552 For use with 5 gallon Fat Bob tanks.....................$14.99 13.16 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
Chrome Frame Neck Cup and Bearing Kit Includes frame cups, races, 2 Timken bearings and chrome dust shields. 12253 Fits Big Twins from 49-88 and most custom frames...... $45.99 APPAREL SEATS & BAGS FOOT HAND Big Twin Front End Adapter for Early XL Models by Vulcan Engineering The Kit consists of a set of fork cups, machined to fit a 57-78 XL Frame, has 1 Timken bearings and billet aluminum dust shields, that are machined as spacers to bring the neck to the same length as a big twin neck. This will allow any stock or aftermarket big twin front ends and springer front ends to be used on a sportster. 668440 Fits 57-78 XL Models.................................$111.99 3 Degree Raked Fork Cup Sets Permit you to rake your bike without having to cut and weld your frame! Offered with or without fork stops, and available in styles to fit a variety of models as noted below. Fork cup sets come with bearings. Made in USA by Motorway. 632004 Fits 49-84 FL/FX/FXWG, 84-88 Softail and most custom frames. With fork stop lug........................... $124.99 632005 Fits 57-78 XL cup set with bearing conversion. With fork stop lug.................................................. $169.99 632006 Fits 49-84 FL/FX/FXWG & 84-88 Softail and most custom frames. No fork stop lug..............................$99.99 632007 Fits 57-78 XL cup set with bearing conversion. No fork stop lug.................................................. $159.99 LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE Fork Cup & Bearing Race Installation Tool by Vulcan Engineering Co. This tool is a must if you are installing raked fork cups. This tool will also install standard unraked fork cups and bearing races. For use with Big Twin models from 36-Up and Sportster models from 82-Up with 1 neck bearings. Made in the U.S.A 697227 Raked/Standard fork cup installation tool...............$79.99 Polished Stainless Steel Internal Fork Stop Kit These kits come with a highly polished fork cup with a nice looking stepped design on them. These are a must for custom frames that need frame cups. They are complete with bearings, cups, races, stop and dustcover. Fit 49-88 OEM frames and most aftermarket frames. 640721 Complete kit...................................... $99.99 GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES 3 Degree Raked Fork Cups for OEM Frames by Vulcan Engineering Co. Looking to add that longer raked front end look with out having to replace your triple trees? Then look no further, the crew at Vulcan Engineering have come up with these slick raked bearing cups that press into your OEM cast neck frame. Kits include a set of stainless steel fork cups, 1 set of neck bearings and races, and a longer fork stem. Made in the U.S.A. 697222 3 degree fork cups for all 87-99 FXR models, 90-05 FXD models (except FXDWG), and 88-03 XL models.................$199.99 697223 3 degree fork cups for all 04-13 XL models.............$199.99 697224 3 degree fork cups for all 06-13 FXD models (except FXDWG)....................................................$199.99 697225 3 degree fork cups for all 89-13 FXST Softail models....$189.99 697226 3 degree fork cups for all 90-08 FXDWG models........$199.99 Sealed Frame Neck Bearings Genuine Timken bearings feature a two way seal that contacts the bearing race and mounting surface. 160048 Fits Big Twins from 49-88 and most custom frames. Includes chrome frame cups, sealed bearings and dust shields.. $74.99 160049 Fits all Softail models from 89-99, FXR and Sportster models from 82-99, Touring models from 80-99 and Dyna Glide models from 92-99. Includes sealed bearings, bearing races................................................... $59.99 Replacement Parts 160047 Sealed bearing* (repl. OEM 48300-60) sold each...... $24.99 160003 Replacement bearing race only for Sportster models from 78-13 and Big Twins 60-13 (repl. OEM 48315-60 sold each................................................... $4.99 *Note: Race and bearing should be replaced at the same time. Use with CC #160003 bearing race only. SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.17
09627 160035 Chrome Dust Shield Set Upper and lower set for all FL, FXWG, Softail and FLT/ FLHT models from 49-88. Includes the original style lower cover and 77-88 upper shield. Set of two. 25279 Replaces OEMs 43865-48A, 48361-80......... $4.99 09625 09626 161010 Replacement Steering Stem Parts The most frequently lost or damaged parts on the forks of most 49-14 Big Twins. 09625 Bearing Jam nut. Sold each......................................... $6.99 09626 Replacement chrome stem nut (sold each)........................... $8.49 09627 Stem nut locktab (pack of 10)....................................... $1.40 160035 Upper nut......................................................... $7.99 Front End Installation Kit Installation kit for stock or CC front ends. Include: bearings (2), upper and lower dust shields, top nut, locktab and acorn crown nut. Note: Not for FLST models. 161010 For FX Softail models ONLY (includes bearings, dust shields, top nut and acorn crown nut with lock tab)................................ $37.99 161011 Parts kit (complete less bearings).......... $28.99 13 Stem Nut and Lock Washers Fits 4-speed FL models from 49-84, FXWG, FXST, FXDWG and Touring models from 80-13 (1"-24 thread). 500602 Stem nut and lock washer kit............. $11.99 160014 Fork stem lockwasher ONLY (repl. OEM 45717-63) pack of 5................................. $1.60 160003 12264 Neck Bearings and Races 12264 Replacement bearing only for Sportster models from 82-13 and Big Twin models 60-13 (repl. OEM 48300-60) sold each....................... $9.99 160003 Replacement bearing race only for Sportster models from 78-13 and Big Twins 60-13 (repl. OEM 48315-60 sold each................... $4.99 Chrome Frame Cups, Bearings and Bearing Races For Big Twin Models 12263 Timken-style chrome cups with races ONLY for Big Twins (except Springer Softail models) from 60-88 (repl. OEM 48311-60) set of 2. Also fits 49-59 Big Twins when CC #12264 bearings are used........................... $25.99 12264 Replacement Timken bearing ONLY for Big Twins from 60-13 (sold each).................................................................. $9.99 26135 Replacement races ONLY for Big Twins 60-13 (repl. OEM 48315-60) set of 2.......................................................................$9.99 For Sportster Models 17381 Custom Timken bearing conversion kit for all Sportster and K models from 54-77. Includes chrome cups and bearings........................... $60.99 13089 Replacement upper Timken bearing only for CC #17381 conversion kit (sold each)............................................................ $16.99 13098 Replacement lower Timken bearing ONLY for CC #17381 conversion kit (sold each)............................................................ $17.49 13099 Replacement Timken bearing ONLY for Sportster models 78-81 (sold each)................................................................. $45.99 12264 Replacement Timken bearing ONLY for Sportster models from 82-13 (sold each)............................................................. $9.99 26135 Replacement races ONLY for Big Twins 78-13 (repl. OEM 48315-60) set of 2.................................................................. $9.99 169901 Replacement bearing race only (sold each - 2 used). For use with CC #17381 $9.99 150999 Replacement chrome frame cups only (set of 2). For use with CC #17381... $18.99 13.18 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL SEATS & BAGS FOOT HAND LIGHTING ELECTRICAL Tweek Bar for 41mm Forks This chrome 2-piece fork brace adds stability to any 41mm front end but is especially useful for overlength forks or when the front fender fell off. 688699 Fits FLH 49-84, FXWG 80-86 and FXST 84-05........... $79.99 Tomahawk Fork Brace for Dyna Models This fork brace is laser cut from 3/16 thick steel and replaces the front fender on your bike while increasing rigidity to the front fork for a more stable ride. Available in either a chrome-plated or gloss black powder coated finish. Designed to work with either a 21 or 19 wheel. Kits come complete with fork brace, mounting brackets and all necessary hardware. Will fit all 06-Up Dyna Models with 49mm forks. 688750 Chrome Tomahawk fork brace, fits all 06-Up Dyna models with 49 mm forks................................. $179.99 688751 Black Tomahawk for brace, fits all 06-Up Dyna models with 49mm forks...................................... $179.90 EXHAUST INTAKE ENGINE GASKETS Fork Braces for Narrow and Wide Glide Forks These custom front fork braces are made from laser cut 3/16 thick steel, allows removal of the front fender and increases rigidity to the front fork better than stock, eliminating any fork twist while safeguarding the integrity of the suspension. The custom styling looks great on any motorcycle, available in black or chrome finish, for use with 19 & 21 wheels & tires. Narrow glide & Wide glide kit applications available, mounting hardware supplied, sold each. 688684 Fork brace for wide glide, black.................... $69.99 688685 Fork brace for wide glide, chrome.................. $69.99 688686 Fork brace for narrow glide, black.................. $66.99 688687 Fork brace for narrow glide, chrome................ $66.99 688685 688684 TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES 688687 688686 SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.19
Headlamp Housing Kit for FL Models This kit features chrome-plated components that are accurate reproductions of the polished Original Equipment parts fitted to most 4-speed FL models from 60-84. It is also a natural for customizing any bike fitted with an early FL-style front end. Top-quality components make the kit a snap to install, with all needed hardware and a 7-inch halogen sealed beam that s included. 26531 Fits 4-speed FL models with Original Equipment or Custom Chrome triple trees 60-84 (handlebar clamp cover is for non-damper models)........................................................... $414.99 Replacement Parts 26536 Set of left and right chrome-plated housings (repl. OEMs 67847-60, 67848-60)...................................................$199.99 26535 Chrome outer trim ring with rubber seal and four retaining clips (repl. OEMs 67712-60A, 67716-60A and 67779-60).................... $18.99 26526 Retaining ring for sealed beam (repl. OEM 67765-60)............$19.99 26893 Inner headlight mount with two adjusting screws for FL models from 60-69 (repl. OEM 67702-65)................................... $29.99 26894 Outer headlight bucket for FL models from 60-84 (repl. OEM 67766-60)............................................................ $29.99 25234 Set of left and right chrome slider covers (repl. OEM 45964-49T). $48.99 26537 Chrome handlebar clamp cover for use with steering damper (repl. OEM 58589-60)....................................................$19.99 26538 Chrome handlebar clamp cover for use without steering damper (repl. OEM 58590-60)...............................................$19.99 26890 13 Doss Headlight Conversion Kits for FL Softail Models These are the original kits still the best and most popular with builders. Other kits on the market are but poor imitations of Custom Chrome s attention to detail, excellent fit and craftsmanship Each piece is hand-polished and chrome-plated Includes the two-piece aluminum head lamp housing, all mounting brackets, headlight bucket, hardware, chrome slider covers, covers for the lower triple tree and handlebar risers. Bolts directly to the existing Original Equipment triple trees. Lamp not included. Kit For FL Softail Models For all FL Softail models from 86-Up (except FLSTS models). Optional Spotlamp Mounting Bar kit replaces the OEM spotlamp bar on Heritage Softail Classic models to mount existing spotlamps and turn signals to the headlight conversion kit (includes mounting bar, spacers, spotlamp/turn signal clamps and chrome hardware). 26890 Headlight housing conversion kit................................................................................................ $459.99 26899 Optional spotlamp mounting bar kit............................................................................................. $65.99 Replacement Parts 26892 Mounting brackets (sold each).................................................................................................... $7.99 26893 Inner headlight mount with two adjusting screws for FL models from 60-69 (repl. OEM 67702-65)..................................... $29.99 26894 Outer headlight bucket for FL models from 60-84 (repl. OEM 67766-60)............................................................. $29.99 26895 Chrome riser cover.............................................................................................................. $29.99 26896 Chrome lower triple tree under cover............................................................................................. $19.99 26897 Chrome right slider cover........................................................................................................ $28.99 26898 Chrome left slider cover......................................................................................................... $28.99 26536 Set of left and right chrome-plated housings (repl. OEMs 67847-60, 67848-60)...................................................... $199.99 26526 Retaining ring for sealed beam (repl. OEM 67765-60).............................................................................. $19.99 26535 Chrome outer trim ring with rubber seal and four retaining clips (repl. OEMs 67712-60A, 67716-60A and 67779-60)..................... $18.99 12555 Spotlight mounting bar ONLY.................................................................................................... $44.99 Note: Early style windshields and brackets should be used with aluminum headlight kits. 13.20 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL SEATS & BAGS Smooth Fork Tins for Late Softails This 3-piece late style fork tin kit is available in chrome or black finish. No grooves or ball mills just smooth, sleek surfaces. 642710 Smooth chrome fork tins 00-14 FLST models....................................... $129.99 642711 Smooth black fork tins 00-14 FLST models...................................... $119.99 26764 651850 Chrome Fork Tins for FL Softail Models These reproductions of the Original Equipment parts are made from highlypolished steel that is then given a chrome-plated or gloss black finish. Fits all 86-13 FLST, FLSTC, FLSTF and 93-13 FLSTN (05-13 FLSTN will not work unless OEM light bar is removed), mounting hardware Included. Available with or without fork slider covers. Note: Models equipped with accessory front passing lamps may need to drill a hole in rear panel to mount the on/off switch. Chrome 26760 Chrome headlight tins 3-piece kit (replaces OEMs 67808-86, 67816-86 and 67820-86)......................................................$64.99 26764 Chrome tins and slider covers 5-piece kit (replaces OEMs 67808-86, 67816-86, 67820-86 and 45964-86).....................................$114.99 Black 651849 Black headlight tins 3-piece kit (repl. OEMs 67808-86, 67816-86 and 67820-86)......................................................$53.99 651850 Black tins and slider covers 5-piece kit (replaces OEMs 67808-86, 67816-86, 67820-86 and 45964-86).........................................$89.99 FOOT HAND LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS Fork Side Trim for Softail Models Chrome tin with no accents for all FL Softail models from 86-14. 220059 Sold in pairs (repl. OEM 67819-86)........ $12.49 26538 Doss Neck Protectors Protects the paint on your frame where the fork stops contact the neck. Held with self-tapping screws. Includes a drill bit, a tube of silicone and all necessary hardware. Fit all Original Equipment Big Twins with cast necks and bosses for padlocks. Polished stainless steel. Sold in pairs. 09138 3/16"-thick.................................................... $18.99 Note: CC #09138 will limit the effective turning radius of your motorcycle. BEFORE TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES AFTER 26889 SHEETMETAL Handlebar Clamp Covers Clamp covers for FL Softail models from 86-99, and 4-speed FL models with or without the steering damper from 60-84. 26538 Chrome handlebar clamp cover for use without steering damper (repl. OEM 58590-60)..... $19.99 26537 Chrome handlebar clamp cover for use with steering damper (repl. OEM 58589-60)..... $19.99 Doss Chrome Lower Triple Tree Covers Chrome-plated stamped steel. These covers bolt under their respective lower triple trees in minutes to clean-up that area on your motorcycle. 26889 Fits FX Softail and Dyna Wide Glide models from 88-13........ $17.99 INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.21
160636 160638 160639 Dual Disc 41 mm Front End Assemblies for FXWG Models from 80-83 Our complete dual disc front end assemblies come complete with chrome upper and lower triple trees, hard chromed fork tubes, springs, and all internal components. Available with polished aluminum lower legs, these front ends are a direct replacement for FXWG models from 80-83 and can be fitted to any Big Twin from 49-99 when 77-83-style dual disc calipers are used. The chrome triple trees feature 3 1/2" riser spacing, a central headlight mounting hole and an identical 3 rake angle as the factory originals. 160635 3 1/2" under stock length.............................$695.99 160636 Stock length.........................................$669.99 160637 2" over stock length..................................$659.99 Installation Kit 161010 For FX Softail models ONLY (includes bearings, dust shields, top nut and acorn crown nut with lock tab).................$37.99 Single Disc 41 mm Front Fork Assemblies for Softail Models from 84-99 Our single disc front end assemblies come complete with chrome upper and lower triple trees, hard chrome stock-length fork tubes, springs, dampeners and all internal components. Perfect for scratch builders or chrome conversions on late Softail models. Direct replacement for Original Equipment parts, that accept stock headlights, risers, fork trim, fenders and axles. Available in both styles with a choice of chrome or polished aluminum lower legs. For FX Softail Models from 84-99 160638 Polished lower legs...................................$695.99 For FL Softail Models from 86-99 160639 Polished lower legs...................................$699.99 160739 Chrome lower legs...................................$639.99 Installation Kit 161010 For FX Softail models ONLY (includes bearings, dust shields, top nut and acorn crown nut with lock tab).................$37.99 13 Custom Chrome Complete Fork Tube Assemblies Come completely assembled, ready-to-install. Ideal for restoration or replacing damaged Original Equipment parts. Assemblies include hard chrome fork tube, springs, cap, and all internal components including the damper rod. Sold each. Fit FX Softail, Dyna Wide Glide and 4-Speed FXWG Models from 84-99 (except Deuce Models) 09291 Stock length with TÜV............................... $124.99 08518 +2" over stock length with TÜV....................... $124.99 08519 +4" over stock length with TÜV....................... $129.99 08520 +6" over stock length with TÜV....................... $134.99 08521 +8" over stock length with TÜV....................... $137.99 08522 +10" over stock length............................... $139.99 Fit 4-Speed FL Models 49-77 09630 Stock length with TÜV............................... $139.99 Fit 4-Speed FXWG Models 80-83 09636-4" under stock length with TÜV....................... $94.99 09650-2" under stock length with TÜV....................... $94.99 09635 Stock length with TÜV................................ $94.99 Fit all FL Softail Models 86-99 09292 Stock length with TÜV............................... $124.99 Fit 4-Speed and 5-Speed Touring Models 77-83 09636 Stock length with TÜV................................ $94.99 09650 +2" over stock length with TÜV........................ $94.99 09635 4" over stock length with TÜV......................... $94.99 13.22 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL SEATS & BAGS FOOT HAND LIGHTING Custom Chrome Fork Sliders for Late Model Motorcycles Unlike our competitors products, our polished legs are buffed to a mirror-like finish. The chrome legs feature high-quality. American chrome-plating for a durable show bike finish. The fork legs for FX Softail models duplicate the style fitted to bikes since 91 with thrubolts to mount the fenders. Kits include sliders, seals, bushings, and hardware. Sold in sets. Fit Single Disc FX Softail, Dyna Wide Glide and 4-Speed FXWG Models from 84-99 09621 Fork sliders chrome for single disc 84-99 FXST, FXSTC, FXDWG, FXWG...............................................$463.99 09298 Polished.............................................$285.99 Fit Single Disc FX Softail and Dyna Wide Glide models from 00-06 601600 Chrome Fork Sliders..................................$379.99 Custom Chrome Single Disc Fork Tube and Slider Assemblies with TÜV for Big Twins Complete front fork leg kits available with chromed sliders. Each set includes hard-chromed fork tubes, sliders, springs, caps, and all internal components. Some assembly required. Sold in sets. Fit FX Softail, Dyna Wide Glide and 4-Speed FXWG Models from 84-99 09294 Chrome, stock length............................. $569.99 ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES Drum Brake Front End Assembly Assembly replaces the stock length FL 49-67 front end with left side drum brake. Each front end comes complete with hard chrome fork tubes, springs, and all internal components. Drum Brake Fork Tube and Slider Assemblies ONLY 160615 Polished lower legs...................................$459.99 160715 Chrome lower legs...................................$569.99 Fork Tube and Slider Assemblies for Big Twins Value-priced alternatives to the single disc leg assemblies listed, complete with polished or chrome-plated lower sliders. Includes hard-chromed fork tubes, sliders, springs, caps, and all internal components, completely assembled and ready-to-install. Sold in sets. Fit all FL Softail Models from 86-99 (except FLSTS) 09238 Chrome, stock length............................. $529.99 09236 Polished, stock length............................. $479.99 Fit FX Softail, Dyna Wide Glide and 4-Speed FXWG Models from 84-99 09239 Chrome, stock length............................. $529.99 09237 Polished, stock length............................. $479.99 09260 Polished, -2" under stock length.................... $479.99 SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.23
654166 631500 654173 654167 631501 654173 Arlen Ness Hot Legs Fork Sliders for Touring Models Hot Legs are the latest from Arlen and Cory Ness, these fork legs will transform your bulky stock forks into a sleek stream lined custom looking front end. Available in two designs Deep Cuts and Smooth and feature a tapered design and hidden axle. Choose from either a chrome plated or black anodized finish. Fits all FLH/FLT Models 2014 Dual Disc 654169 Smooth Hot Legs, Chrome............................. $669.99 654172 Deep Cut Hot Legs, Black.............................. $669.99 654168 Deep Cut Hot Legs, Chrome............................ $669.99 654173 Deep Cut Hot Legs, Black.............................. $669.99 Single Disc 654167 Smooth Hot Legs, Chrome............................. $669.99 654171 Smooth Hot Legs, Black................................ $669.99 654166 Deep Cut Hot Legs, Chrome............................ $669.99 654170 Deep Cut Hot Legs, Black.............................. $669.99 Fits all FLH/FLT Models from 08-13 Dual Disc 631500 Smooth Hot Legs, Chrome............................. $599.99 631501 Smooth Hot Legs, Black................................ $599.99 631504 Deep Cut Hot Legs, Chrome............................ $599.99 631505 Deep Cut Hot Legs, Black.............................. $599.99 Fits all FLH/FLT Models from 00-07 Dual Disc 631502 Smooth Hot Legs, Chrome............................. $599.99 631503 Smooth Hot Legs, Black................................ $599.99 631506 Deep Cut Hot Legs, Chrome............................ $599.99 631507 Deep Cut Hot Legs, Black.............................. $599.99 609794 13 Forkerz 39-43mm Fork Wrap LED Lights by Radiantz Forkerz LED fork wrap lights are in a clear tube. Just peal and wrap them around the fork and lock them into place with the new built in zip tie for an easy install. You can wire them to be either white or amber LEDs. Fits fork tubes 39mm to 43mm. Sold as a pair. 609794 Forkerz white or amber LED fork lights............... $124.99 13.24 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL SEATS & BAGS FOOT Arlen Ness Deep Cut Fork Boots The new Deep Cut fork boots will radically change the look of your front end. They are 654000 654001 machined from forged 6061-T6 billet aluminum and designed to replace your OEM fork boot covers. Available in either a chromeplated or black anodized finish. 654000 Chrome, for all 86-14 FLH/FLT........................ $259.99 654001 Black, for all 86-14 FLH/FLT........................... $259.99 654162 Chrome, for all 2014 FLH/FLT models.................. $259.99 654163 Black, for all 2014 FLH/FLT models.................... $259.99 Fork Slider Covers These quality replacement slider covers come in a show quality chrome or gloss black finish and are available in stock or 2 over lengths. They fit FL models 49-84, FLT s 80-13 and FL Softails 86-Up. Sold in pairs. 688838 Fork slider covers black, stock length................ $46.99 25234 Fork slider covers chrome, stock length.............. $48.99 688837 Fork slider covers black, +2 length.................. $48.99 688836 Fork slider covers chrome, +2 length................ $46.99 For all 14-Up Touring models 688753 Fork slider covers black, stock length................ $57.99 688752 Fork slider covers chrome, stock length.............. $57.99 HAND LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH Jammer Rubber Gator" Fork Boots These are a Mr Lucky find old school gator fork boots in 39mm, 41mm and now, 35mm & 49mm as well! Available in basic Black, or kick-ass Red that look so sweet with our Red grips! The 41mm boots measure 9" extended, approx. 4 1/2" collapsed, 1-58" upper I.D. (41mm) and 2 9/16" lower I.D. (65mm). The 39mm fork boots measure 7" extended, approx. 3 1/2" collapsed, 1 1/2" upper I.D. (39mm) and 2 9/16" lower I.D. (65mm). The new 35mm fork boots measure 182mm X 35mm X 60mm and fit early XL s and many others. The new 49mm- Short versions fit FXD Dyna Glides thru 06. The new 49mm-Long versions fit FXDWG Dyna Wide Glides thru 06. A way cool look for that retro inspired scoot! Note: Must remove fork tubes to install. Sold in Pairs. 150125 Black Fork Boots-41mm................................$36.99 632043 Black Fork Boots-39mm................................$34.99 632044 Red Fork Boots-41mm.................................$36.99 632045 Red Fork Boots-39 mm................................$34.99 632804 Black Fork Boots-35mm................................$29.99 632800 Black Fork Boots-49 mm Short. Fit FXD Dyna............$35.99 632801 Red Fork Boots-49 mm Short. Fit FXD Dyna..............$35.99 632802 Black Fork Boots-49 mm Long, FXDWG Dyna Wide Glide................................................... $39.99 632803 Red Fork Boots-49 mm Long, FXDWG Dyna Wide Glide...$39.99 Eazy-On Fork Boot Covers Nothing looks cleaner on an old school ride than a set of rubber fork boots. But, until now, you had to disassemble your front end to put them on... not something you really look forward to doing. Well, the people at Kijima have listened, and added an Eazy-on solution to their popular 39mm & 41mm rubber fork boots. Split down the back they can be easily slid over the forks, aligned, then attached together with the interlocking system/glue provided. Now, a super Retro look, in far less time! Sold in Pairs. 682761 EZ-On Black Fork Boot Covers, 39mm. Pair............. $84.99 632806 EZ-On Black Fork Boot Covers, 41mm. Pair............. $84.99 DRIVELINE WHEELS TIRES & BRAKES SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.25
651852 Chrome Fork Boot Caps Fit over the stock boots. Sold in pairs. Fit Sportster, FX and FXR models with 35 mm Showa forks from 75-87 28073 Replaces OEM 45350-84T..............................$16.99 Fit 4-speed FL models with 41 mm forks from 49-E77 28080 Sold in pairs..........................................$14.99 Fits FXWG models from 80-86 and Softail models from 84-99 except FL Softail and Springer Softail models 160059 Sold in pairs..........................................$12.99 160063 Fork Boot Covers These covers fit easily over the rubber dust boot without disassembling the front end. Each 2-piece cover is held together with 2 interlocking springs. Available in either a chrome-plated or gloss black finish. Fits all 84-Up FXST, 91-05 FXDWG, 80-86 FXWG. 160063 Chrome, fork boot covers............................. $18.99 651852 Black, fork boot covers............................... $21.99 160067 Replacement springs for CC #160063 (pack of 10)........ $5.99 Fork Boots These are replacement items for the stock fork boots. Sold in pairs. 25454 Fork boots for FX and Sportster models from 77-13 (replaces OEM 46001-71) sold in pairs.............................$4.49 12920 Fork boots for 4-speed FL models from 49-E77 (sold in pairs)......................................................$5.99 12921 Fork boots for Softail 84-13, FXDWG 84-05 and 4-speed FXWG models from 80-83 (except Heritage Softail & Fat Boy models) sold in pairs...........................................$5.99 26104 Fork boots for 35 mm Showa forks from 75-87 (replaces OEM 45404-75T) sold in pairs.................................$5.99 160057 651851 Fork Boots with Dust Shields Here s just what is needed to perk up a tired set of forks. Supple rubber fork boots with chrome-plated or gloss black dust shields help make your forks look like new. 160057 Chrome, Fits, Dyna 88-05, FXR, Sportster 88-13 models with 39 mm forks.............................................$19.99 651851 Black, Fits Dyna 88-05, FXR, Sportster 88-14 models with 39 mm forks.................................................$19.99 13 BE SURE TO USE QUALITY MOTOR FACTORY FORK OIL FIND THEM IN THE GENERAL SECTION PAGE 16.07 13.26 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL ALL IN ONE BOX FOR A COMPLETE CHANGE SEATS & BAGS FOOT HAND LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES FIND THEM IN THE GENERAL SECTION PAGE 16.05 RevTech High Performance Complete Oil Change Kit You can do it yourself. You know what you re doing. Just get the complete kit from your Custom Chrome Dealer. The kit contains everything you need to change the motor, primary and transmission oils in your motorcycle. RevTech High Performance blended 20W50 motor oil, 80W90 transmission oil, primary lube, magnetic oil filter, derby & inspection cover gasket and drain plug o-rings.* *Various model specific kits available SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.27
160042 160037 12920 12921 25454 26104 25910 09285 SEE PAGE 13.33 25228 15232 15233 15241 15240 26485 09638 09634 09639 25914 09287 09288 25227 25225 26493 13 500584 25913 160037 160042 09298 09621 13.28 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
Front Fork Parts for Big Twins Listed below in CC part number order. 09285 Fork spring for FX Softail and 4-speed FXWG models (replaces OEM 46048-84) sold in pairs.......................... $27.99 09287 Damper tube assembly for FX Softail, Dyna Wide Glide and 4-speed FXWG models from 84-99 (replaces OEM 45418-84)................................................... $19.99 09288 Damper tube assembly for FL Softail models 86-99 (replaces OEM 45932-86) sold each............................ $19.99 09298 Polished........................................... $285.99 09621 Fork sliders chrome for single disc 84-99 FXST, FXSTC, FXDWG, FXWG............................................. $463.99 09629 Dampener retaining ring FL models from 49-E77 (replaces OEM 46172-48) pack of 10............................ $0.80 09634 Damper rebound spring (repl. OEM 45855-77) sold each. $3.99 09638 Chrome washer, fork cap spacing. Fits FXWG, FXST and FXDWG models from 80-99 (replaces OEM 5710) pack of 10.................................................... $0.90 09639 Fork tube plug oil seal (replaces OEM 45733-48) pack of 10.................................................... $0.50 12920 Fork boots for 4-speed FL models from 49-E77 (sold in pairs).................................................... $5.99 12921 Fork boots for Softail 84-13, FXDWG 84-05 and 4-speed FXWG models from 80-83 (except Heritage Softail & Fat Boy models) sold in pairs......................................... $5.99 15232 Chrome fork tube caps for Sportster, FX and FXR models with fine threads from 73-86 (replaces OEM 45993-73) sold in pairs................................................... $20.99 15233 Chrome fork tube caps for FL models from 49-E77 (replaces OEM 45754-60) sold in pairs.......................... $19.99 15240 Upper fork tube plugs for all Showa Wide Glide forks from late 77-13 (except 84-later Touring models or FL model adjustable forks) replaces OEM 45838-77 (sold in pairs)................................................... $24.99 15241 Chrome fork tube caps for all Softail, Dyna Wide Glide and 4-speed FXWG models from 80-13 (except Springer Softail models) replaces OEM 45419-80 (sold in pairs)......... $15.99 25225 Damper tube assembly fits FXWG models from 80-83 (replaces OEM 45418-80) sold each............................ $15.99 25227 Damper tube assembly fits 4-speed FL models from late 77-84 (replaces OEM 45831-77) sold each................... $18.99 25228 Lower bushing, dampener tube. Fits FL, FXWG, FXST and FXDWG models late 77-99 (replaces OEM 45834-77) sold each.................................................... $8.99 25454 Fork boots for FX and Sportster models from 77-13 (replaces OEM 46001-71) sold in pairs........................... $4.49 25910 Bushing set, brake caliper. Fits all dual disc models 77-83 (replaces OEMs 46018-77, 46019-77) sold in pairs (requires 1 pair per caliper)...................................... $6.99 25913 Bushing, brake caliper (long). Fits FL models from 72-84 (replaces OEM 45821-75) sold each.................... $3.99 25914 Bushing, brake caliper (short). Fits FL models from 72-84 (replaces OEM 45822-75) sold each.................... $2.99 26104 Fork boots for 35 mm Showa forks from 75-87 (replaces OEM 45404-75T) sold in pairs............................... $5.99 26485 Upper fork tube plugs for 49-E77 FL forks (replaces OEM 45776-49) sold in pairs............................... $15.99 26493 Damper tube assembly for all 4-speed FL models from 49-E77 (replaces OEM 46161-49) sold each................... $43.99 160037 Axle pinch cap, aluminum. Fits all Big Twins with 41 mm front forks from 49-99 (replaces OEM 45832-77) sold each... $13.49 160042 Drain screw and washer kit for FL models late 77-84, FXWG, FLT and Softail models 80-99 (replaces OEM 45858-77) pack of 5................................................. $7.49 500584 Dampener tube screw with washer for most models from 75-99 (replaces OEM 45405-75A) pack of 5............. $0.90 APPAREL SEATS & BAGS FOOT HAND LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE 15240 Damper for FL Front Ends A complete oil-shock damper valve assembly manufactured to rigid specifications. 26493 Damper tube assembly for all 4-speed FL models from 49-E77 (replaces OEM 46161-49) sold each.... $43.99 Upper Fork Tube Plugs For 49-E77 FL forks (repl. OEM 45776-49). 26485 Upper fork tube plugs for 49-E77 FL forks (replaces OEM 45776-49) sold in pairs.............. $15.99 GASKETS TRANSMISSION & CLUTCH DRIVELINE 15241 Chrome Fork Tube Plugs and Caps Upper Fork Tube Plugs Fits all Showa Wide Glide forks from late 77-13 (except 84-13 FLT, FLHT and FLHS models or FL model adjustable forks). Sold in pairs. 15240 Upper fork tube plugs for all Showa Wide Glide forks from late 77-13 (except 84-later Touring models or FL model adjustable forks) replaces OEM 45838-77 (sold in pairs)..$24.99 Slider Tube Caps Fits all Softail, Dyna Wide Glide and 4-speed FXWG models from 80-13 (except Springer Softail models). Sold in pairs. 15241 Chrome fork tube caps for all Softail, Dyna Wide Glide and 4-speed FXWG models from 80-13 (except Springer Softail models) replaces OEM 45419-80 (sold in pairs)............ $15.99 Fork Tube Baffle Assembly Accurate reproductions of all of the parts that went into the baffle valve and brought together as an assembly. Fits the front forks of all FL models from 49-E77. 09550 Sold each...................$18.99 15232 15233 Chrome Fork Tube Caps 15232 Chrome fork tube caps for Sportster, FX and FXR models with fine threads from 73-86 (replaces OEM 45993-73) sold in pairs................... $20.99 15233 Chrome fork tube caps for FL models from 49-E77 (replaces OEM 45754-60) sold in pairs........................ $19.99 WHEELS TIRES & BRAKES SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.29
13 Genuine James Gaskets Fork Seals Patented seal design Superior material for longer seal life Innovative seal design reduces lip distortion and drag Renowned James Gasket quality 49 mm Fork Seals 667857 06-13 Dyna, 01-13 V-Rod (except VRSCR) and 08-12 FXCW Rocker models, sold in PAIRS............................$5.50 41 mm Fork Seals 667456 84-13 Softail, 93-05 FXDWG and 87-13 FLT models, sold EACH.....................................................$11.99 667458 00-07 Deuce FXSTD models, sold in PAIRS................$6.50 667451 84-86 FLT, FLHTP models, sold EACH....................$12.99 667461 77-84 FL, FLH, FLT models, sold EACH...................$11.99 667452 49-77 FL, FLH models, pack of 5.........................$4.60 39 mm Fork Seals 667457 87-13 XL/FXR, and 91-05 Dyna, sold EACH................$7.99 667455 75-83 XL, FX Showa style, sold EACH.....................$8.49 667454 73-77 XL, FX Kayaba style, pack of 5.....................$6.20 667453 71-72 XL, FX, pack of 5.................................$3.60 35 mm Fork Seals 667460 84-87 FX, FXR, XL models, sold EACH....................$8.99 39 mm fork seals 667450 Fork dust seal cover 39 mm for XL and FXR models 88-02, FXD models 91-05..........................................$5.49 49 mm fork seals 667856 Oil Seal, dust Seal front fork for Dyna models 06-13 and V-Rod models 01-14..........................................$5.50 654003 Arlen Ness Complete Lowering Kits The kits will give you just about everything you need to lower the front and rear of most late model Big Twins. The specially designed fork dampers lower the front end without having to replace the factory springs. Each kit includes specially designed fork dampers, adjustable rear lowering kit, and a 1 shorter kickstand (fork oil not included) 654002 Fits 07-13 Touring models (except models with soft bags)....................................................$249.99 654003 Fits all 00-06 Softail models (except Springer & Deuce models)....................................................$179.99 Damper Tube Assemblies Complete damper tube assemblies for most 39 mm Showa-equipped Big Twin models from 77-99. Sold each. 25225 160044 160045 For FXWG models from 80-83 25225 Damper tube assembly fits FXWG models from 80-83 (replaces OEM 45418-80) sold each........................................ $15.99 For 4-speed FL models from late 77-84 25227 Damper tube assembly fits 4-speed FL models from late 77-84 (replaces OEM 45831-77) sold each............................... $18.99 For FX Softail Dyna Wide Glide and 4-speed FXWG Models 84-99 09287 Damper tube assembly for FX Softail, Dyna Wide Glide and 4-speed FXWG models from 84-99 (replaces OEM 45418-84)...... $19.99 For FL Softail Models 86-99 09288 Damper tube assembly for FL Softail models 86-99 (replaces OEM 45932-86) sold each........................................ $19.99 Fork Leg Lower Stop An essential component of Showa front forks. Precision-machined from aluminum billet. Fits all Wide Glide forks from late 77-07. Sold each. 25228 Lower bushing, dampener tube. Fits FL, FXWG, FXST and FXDWG models late 77-99 (replaces OEM 45834-77) sold each.................... $8.99 Seal Retaining Rings An accurate reproduction of the Original Equipment part. Fits 80-86 FXWG; Softail and Dyna Wide Glide models from 84-Up; 49-84 4-speed FLs, and 80-83 FLT/FLHT models. 09631 Fork seal retaining rings (repl. OEM 45842-77) pack of 10..........$1.20 Seal Retaining Rings Sold in 10 packs. 160044 Fits FXR and Sportster models with 39 mm forks from 87-03 (repl. OEM 45905-87).................. $10.49 160045 Fits FX, FXR and Sportster models with 35 mm Showa forks from 75-87 (repl. OEM 45908-80).. $12.99 Arlen Ness Front Lowering Kits This Arlen Ness design simplifies lowering the front of your bike. These specially designed fork dampers are shortened and drilled in a strategic position to maintain a factory ride quality with a lowered stance. Each kit comes with 2 complete damper assemblies and utilizes the OEM springs. 654005 Fits all 84-99 FXST/FLST Softail models with 41mm forks (lowers FXST 2.5 & FLST 2 ).........$49.99 654007 Fits all 90-05 FXD Dyna models with 39mm forks (lowers FXD 2 & FXDL/ FXDS 2.75 ) and 97-13 XL models (lowers front end 2 ).........$49.99 13.30 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL SEATS & BAGS Motor Factory Fork Seals and Rebuild Kits Fork seals only or kits that include a pair of fork seals, and necessary washers to rebuild forks to like new performance. For Sportster, Dyna Glide, FX and FXR Models Seals (pack of 10) 54373 Fit Sportster and FX models from 73-76 with Kayaba forks (repl. OEM 45927-73)..................................$1.60 54376 Fit Sportster, FX and FXR models from 75-83 with Showa forks (repl. OEM 45400-75)............................ $2.20 54383 Fit Sportster, FX and FXR models from 84-87 with 35 mm Showa forks (repl. OEM 45387-83)..................... $2.30 54387 Fit Sportster, Dyna Glide and FXR models from 87-13 with 39 mm Showa forks (repl. OEM 45378-87)..................$1.65 Rebuild Kits 19494 Fits Sportster and FX models from 71-72................ $2.99 25373 Fit Sportster and FX models from 73-76 with Kayaba forks (repl. OEM 45927-73)................................. $2.99 25383 Fit Sportster, FX and FXR models from 75-83 with Showa forks (repl. OEM 45400-75)............................ $4.99 25384 Fit Sportster, FX and FXR models from 84-87 with 35 mm Showa forks (repl. OEM 45387-83)..................... $4.49 25387 Fit Sportster, Dyna Glide and FXR models from 87-13 with 39 mm Showa forks (repl. OEM 45378-87)................. $3.49 For FL, FLT/FLHT, 4-Speed FXWG, Softail and Dyna Wide Glide Models Seals (pack of 10) 54349 Fit FL models 49-E77 (repl. OEM 45852-48)..............$1.20 54377 Fit FL models late 77-84, FXWG and FLT/FLHT models from 80-83 (repl. OEM 45843-77)............................$1.80 54384 Fit FLT/FLHT, 4-speed FXWG, Softail and FXDWG (except 06-13) models from 84-13 (repl. OEM 45875-84).........$1.70 Seals (pack of 5) 160225 Fits FLT, FLST, FXWG and FXST models 84-99. (repl. OEM 45875-84)............................................ $2.20 Rebuild Kits 19362 Fit FL models 49-E77 (repl. OEM 45852-48)............. $9.99 25330 Fit FL models late 77-84, FXWG and FLT/FLHT models from 80-83 (repl. OEM 45843-77)........................... $5.99 25385 Fit FLT/FLHT, 4-speed FXWG, Softail and Dyna Wide Glide models from 84-05 (repl. OEM 45875-84) seal and retainer clip only.............................................. $9.99 160066 Fits FXST, FLST, FXWG and FXDWG models from 84-99. (repl. OEM 45849-87)........................................$7.49 Complete Rebuild Kit for 49mm Forks This comprehensive rebuild kit contains everything necessary to rebuild a leaking 49mm front end from the bottom up. 688661 Rebuild kit for 49 mm forks......................... $51.99 41 mm Fork Slider Assembly/Rebuild Kit Complete high quality kit includes all necessary bushings, seals, washers and clips to assemble or rebuild a set of 41 mm fork legs. 688308 Fits all front ends from 84-13............... $25.99 160173 Fork Tube Bushings for 39 mm Front Ends Fits 39 mm forks used on Sportster, FXR and Dyna Glide models (except FXDWG) from 87-13. Sold in pairs. 160173 Upper bushing (repl. OEM 45461-87)................. $5.00 160174 Lower bushing (repl. OEM 45465-87)................. $3.50 25327 25240 FOOT HAND LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES 160170 160172 Fork Tube Bushings with Teflon Coating for 41 mm Front Ends Fits all models from 84-13 with 41 mm forks. Sold in pairs. 160170 Lower bushing (repl. OEM 45866-84)....................$5.00 160172 Upper bushing (repl. OEM 45940-84)....................$5.00 25239 Fork Slider Bushings Upper and lower fork slider bushings for most Wide Glide front forks. For Models from 49-E77 Fit all models with FL front fork sliders, and are of the correct rolled type, steel backed with full surface bronze interior facing. Lower bushing bronze face features a spiral oil groove for smoother fork action and additional lubrication. 25239 Lower bushing (sold each)........................... $9.99 25240 Upper bushing (sold each)........................... $9.99 25327 Felt washer, upper oil seal (pack of 10)................ $0.90 For Models from 84-13 with 41mm forks Fit the front sliders on all Wide Glide fork assemblies 84-13 with 41mm forks. 09272 Lower bushing (repl. OEM 45866-84) sold each........ $5.99 09271 Upper bushing (repl. OEM 45940-84) sold each........ $5.99 SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.31
Monotube Fork Cartridge Kit by Progressive Suspension True high performance front suspension has finally made its way to the HD Touring line. Our state of the art Monotube Fork Kit represents the pinnacle of bagger front end handling. High performance specialty components replace the sloppy open bath damping found in HD forks. The kit features a set of gas charged Monotube dampers and a set of custom tuned fork springs. This kit will convert your standard dual damper and single cartridge forks found on 97-13 Touring models to a true High-Performance Cartridge Forks! This kit is a direct internal component replacement for all FLH/FLT models from 84-13. No modifications to forks are required. Fits Touring Models 680129 Monotube Fork Cartridge kit, Fits all Touring models from 97-13.......................................................................$399.99 693900 1-2 Lowered Monotube Fork Cartridge kit, fits all Touring models from 97-13.................................................... $439.99 693928 Monotube Fork Cartridge kit, Fits all Touring models from 84-96................................................................... $399.99 693929 1-2 Lowered Monotube Fork Cartridge kit, fits all Touring models from 84-96.................................................... $439.99 690186 Monotube Fork Cartridge kit, Fits all Tri Glide models from 09-13.................................................................. $339.99 13 Performance Fork Springs by Progressive Suspension Progressively-wound springs are made using the finest spring material with a Manufacturer s Lifetime Warranty. They eliminate sag, reduce nose dive under braking, improve stability and increase ride comfort. Stock-Height Spring Kits Sold in sets that include correct spacers for the application. 690265 Fits 49mm forks on FLH/FLTR models from 14-Up................................ $109.99 28441 Fits 41mm forks on FLHT/FLTR models from 80-13 (except 02-05 model with cartridge style forks), FLHR Road King models from 94-13, all Softail models from 84-13, FXDWG models from 84-05 and all 4-speed FX/FL models.........................................$92.99 680078 Fits 41mm forks on FLHT/FLTR models from 02-05 with Cartridge style forks (except Road King).........................................................................$92.99 680090 Fits FXDX/T models from 00-05..................................................$92.99 28443 Fits 39 mm Showa forks on 87-14, FXLR and 88-04 Sportster and FXR models (except Hugger, Convertible, Sport Edition and FXRT models).............................$92.99 696156 Fits 39mm forks on XL 883/R/C/L models and 1200/R/C/L models 04-13...............$92.99 28581 Fits 39 mm Showa forks on Sportster Standard and Deluxe models 92-03; Sportster 883 Hugger and 1200C 92-03; and Dyna Super Glide 95-05............................$92.99 28442 Fits 39 mm Showa forks on FXDL from 93-05; FXDS-Convertible from 94-05; FXDB and FXDC from 91-92; FXRS Sport from 87-94; FXRT and FXRS Convertible models 88-94..............................................................................$92.99 28440 Fits all 35 mm Showa forks from 75-87...........................................$92.99 28809 Fits V-Rod models from 02-13 and FXCW Rocker & Dyna models from 06-13.........$92.99 696156 Fits 39mm forks on XL 883/R/C/L models and 1200/R/C/L models 04-13...............$92.99 Fork Lowering Kits An easy and inexpensive way to drop the front end of your bike one or two inches. Includes progressively-wound fork springs, spacers, and lowering components. 690266 Fits 49 mm forks on FLH/FLTR models from 14-Up............................... $118.99 28542 Fits 41mm forks on FLHT/FLTR models from 80-13 (except 02-05 model with cartridge style forks), FLHR Road King models from 94-13, all Softail models from 84-13, FXDWG models from 84-05 and all 4-speed FX/FL models....................................... $118.99 680089 Fits all 49mm forks on FXD/B/L/C/WG/35 models from 06-13...................... $118.99 28541 Fits 39 mm Showa forks on FXR models 87-94, XL models 87-03, FXDX 99, Dyna models (except FXDWG) 87-00....................................................... $118.99 28540 Fits 35 mm Showa and Kayaba forks on all Sportster, FX and FXR models from 84-87............................................................................ $118.99 28810 Fits V-Rod models from 02-13 (drops the front end 1").......................... $118.99 Note: Careful evaluation of fender-to-frame clearance is required when installing any lowering kit. 13.32 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL SEATS & BAGS Heavy Duty 39 mm Fork Springs by Progressive Suspension Now available in higher rates for the Dyna and Sportster owners looking for a higher level of performance and load tolerance. Spring rates have been chosen to reduce front end dive during braking, yet still provide excellent ride comfort. 690195 Heavy duty 39 mm fork springs........................$109.99 Burly Fork Lowering Kits Lower the front forks 1 1/4" or 2" depending on the spacer used. Simple installation with only minor disassembly of forks necessary, and easy to return to stock simply put original fork springs back in. Progressively wound springs deliver a compliant ride, yet resist bottoming, while bottoming-out at the same point as stock to maintain ground clearance. 28470 Fits 41mm forks on Touring models from 80-13 (except 02-05 models with cartridge forks), all Softail models from 84-13 (except FXCW /C), FXDWG models from 93-05 and all 4-speed models with 41mm forks...............................$99.99 28471 Fits 39 mm Showa forks on Sportster, FXR from 87-13 and Dyna Glide models from 91-05..............................$99.99 28472 Fits 35 mm Showa forks on Sportster, FX and FXR models from 84-87................................................$99.99 Note: Careful evaluation of fender-to-frame clearance is required when installing any lowering kit. 690243 High Performance Cartridge Fork Kits for Dynas by Progressive Suspension True high performance front suspension is finally available for the Dyna line. The asymmetrical design places a preload adjuster over a progressive rate spring in one leg and an aluminum bodied, sealed cartridge damper on the other. The result is superior damping and ride control combined with tunable preload. Available for 06-Up Dyna applications (49mm). Adjustable preload Improved Resistance to Front brake dive Improved front end stability Improved Cornering Improved Bottoming Control 690243 Cartridge fork kit FXD 06-Up (ex. FXDWG & FXDF)... $399.99 690244 Cartridge fork kit FXDWG 06-08.................... $399.99 690245 Cartridge fork kit FXDWG 10-11.................... $399.99 FOOT HAND LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE 690225 690228 WHEELS TIRES & BRAKES Progressive Suspension Drop-In Front Lowering Kits Forget everything you know about lowering motorcycle front ends. Progressive Suspension has just completely changed the game! Pull up to 2 out of the front end of your bike without the hassle of disassembling the forks, pulling the front wheel or even changing the fork oil and the whole process can be done with basic tools. 680030 Fits all 88-13 Sportster models (except Sport model).....$129.99 680031 Fits 91-92 FXD/B/C, 93-05 FXDL, 94-00 FXDS-Conv, 95-05 FXD/C, and 99 FXDX models.................................$129.99 680032 Fits 08-13 FXCW /C models and 06-13 FXD/B/C/L/WG/35 (except Fat Bob model)......................................$129.99 680033 Fits all 80-13 Touring models with NON-CARTRIDGE style forks and all 84-14 Softails (except FXCW /C models).........$129.99 680034 Fits all 02-05 Touring models with CARTRIDGE style forks $84.99 Fork Preload Adjusters by Burly High performance suspension preload adjusters for 88-Up Sportsters and 91-Up Dyna models. Easily tune your front suspension to suit your weight and riding style. Simple installation and 20mm of adjustment range via hex key. Black or machined aluminum finish. 690225 Fork preload adjusters 39mm...................... $139.99 690226 Fork preload adjusters 39mm black................. $139.99 690227 Fork preload adjusters 49mm...................... $139.99 690228 Fork preload adjusters 49mm black................. $139.99 SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.33
680004 422 Heavy-Duty Adjustable Ride Height Shocks for Softail Models by Progressive Suspension Riding 2-up with stuffed saddlebags can quickly overwhelm your Softails suspension. Progressive has solved this problem by adding a higher rate spring to this already fully adjustable shock, providing better load and bottoming control. Combine that with variable ride height and tunable spring preload to setup your bike to fit your riding style. The 422 series shocks are based on a monotube damper system using and internal nitrogen charge, they are designed to eliminate oil cavitation and help create a consistent ride. Available in chrome finish only. Sold in pairs. 690184 Fits all models from 89-99.............................$499.95 690185 Fits all models from 00-14.............................$499.95 Chrome HD Adjustable Ride Height Shocks for Softail Models by Progressive Suspension High performance shocks to replace the Original Equipment units on Softail models from 89-12. They feature adjustable mounts that permit the bike to be lowered up to two full inches from stock ride height. Improved compression and rebound damping give you greater control with less bottoming out and the spring preload is adjustable. Available in chrome finish only. Sold in pairs. 680004 Fits all models from 89-99.............................$499.99 680005 Fits all models from 00-14.............................$499.99 13 Chrome Adjustable Shocks for Softail Models These shocks are chrome-plated and come complete with a built-in lowering kit. They ll lower any early Softail model up to 3" inches. 05997 Fit all Softail models from 89-99.......................$329.99 13.34 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
444 Series Shocks by Progressive Suspension After more than a decade of ruling the roads with their road proven 440 Series shocks, they ve unveiled another breakthrough design. Dubbed Frequency Sensing Technology (FST) for its unique ability to dynamically adjust damping as you ride. The result is superior performance no matter the road conditions. A top mount threaded preload adjuster allows for fine tuning with a simple twist of the cap. Limited lifetime warranty & made in the USA. FLH/FLT Models Standard Spring Shocks Chrome 690106 13 fits 80-14......................................................... $669.95 690104 12.5 fits 80-14....................................................... $669.95 690140 12 fits 80-05......................................................... $669.95 690164 12 fits 06-14......................................................... $669.95 690112 11.5 fits 80-05....................................................... $669.95 690160 11.5 fits 06-14....................................................... $669.95 Black 690105 13 fits 80-14......................................................... $624.95 690103 12.5 fits 80-14....................................................... $624.95 690139 12 fits 80-05......................................................... $624.95 690163 12 fits 06-14......................................................... $624.95 690111 11.5 fits 80-05....................................................... $624.95 690159 11.5 fits 06-14....................................................... $624.95 FLH/FLT Model Heavy Duty Spring Shocks Chrome 690124 13 fits 80-14......................................................... $669.95 690122 12.5 fits 80-14....................................................... $669.95 690142 12 fits 80-05......................................................... $669.95 690158 12 fits 06-14......................................................... $669.95 690120 11.5 fits 80-05....................................................... $669.95 690162 11.5 fits 06-14....................................................... $669.95 Black 690123 13 fits 80-14......................................................... $624.95 690121 12.5 fits 80-14....................................................... $624.95 690141 12 fits 80-05......................................................... $624.95 690157 12 fits 06-14......................................................... $624.95 690119 11.5 fits 80-05....................................................... $624.95 690161 11.5 fits 06-14....................................................... $624.95 FXD/FXDWG Dyna Models Standard Spring Shocks Chrome 690132 12.5 fits 91-14....................................................... $669.95 690146 11.5 fits 91-14....................................................... $669.95 690130 12 fits 91-14......................................................... $669.95 Black 690131 12.5 fits 91-14....................................................... $624.95 690129 12 fits 91-14......................................................... $624.95 690145 11.5 fits 91-14....................................................... $624.95 APPAREL SEATS & BAGS FOOT HAND LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.35
944 Ultra Touring Series Shocks by Progressive Suspension Specifically designed to deliver a comfortable ride at a 1 lowered stance. Built around Progressives newest Frequency Sensing Technology (FST) allows the shocks to sense the frequency of a bump and automatically adjust dampening for a superior ride. The Ultra Touring Shocks utilize all the suspension travel provided by these 13 eye to eye units but provide a 1 lowered ride height with the use of a Progressive rate main spring specifically designed for Touring models. The unique Ultra Touring spring combination not only delivers a lowered ride height while it s being ridden, but also while it s on the kickstand. These shocks are High Pressure gas charged for consistent performance and come in a gloss black finish. 690181 944 Ultra Touring Shocks heavy duty for all Touring models from 80-14..........................................$759.00 690196 944 Ultra Touring shock standard for Touring models 80-14....................................................$759.99 412 Cruise Series Shocks by Progressive Suspension The 412 Cruise is the perfect balance of lowered stance and ride quality. By combining a flat-wire spring with a progressive main spring the 12.5 shock sits like 11.5 units under the weight of the bike, yet utilize the full stroke as terrain demands it. The result is a lowered shock that rides like a traditional height unit. Five position preload adjuster Gas charged damper Fits 77-13 Sportster applications Black or chrome main spring 690246 412 Cruise shocks black 77-Up XL......................$349.99 690247 412 Cruise shocks chrome 77-Up XL....................$349.99 13 Stiletto Sportster Shocks by Burly Burly Stiletto shocks are coil sprung sexiness. Created to give your Sportster the attitude and suspension travel that a proper café, Scrambler or post-apocalyptic XL wants and needs. The high performance damper is wrapped in a spring combination designed specifically to deal with subtle road noise and imperfections, while the main coil handles the big hits and controls bottoming. The result is a plush ride that s not afraid to play rough. Fitment for most 86-03 XL models. 690201 Stiletto 15 shocks for XL 86-03...................... $299.99 690206 Stiletto 13 shocks for XL 86-03...................... $299.99 May require modification to exhaust brackets to open up clearance for belt. 416 Series Air Shocks by Progressive Suspension The Original Air Shock from Progressive Suspension features a machined aluminum air chamber for perfect sealing surfaces, heavy duty springs, air adjustability and velocity sensitive, multi-stage valving and full dust boot for additional protection. The 416 Series is the perfect choice for the touring rider who carries a varied load. Clear anodized brushed aluminum bodies and easy-to-install air lines are featured. Sold in pairs. 28563 13" for FLT, FLHT and FLHS models from 80-13; FXRT 83-84....................................................$399.99 690187 13 for Tri Glide models from 09-Up...................$401.65 13.36 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL 970 Series Piggyback Performance Shocks by Progressive Suspension Inspired by racers, riders and those who demand more of their bikes than weekend coffee runs or a leisurely putt around town. The 970 series shocks are built in the USA and combine a high-pressure gas mono-tube design with progressive rate springs, deflective disc-valving routed through two unique circuits. The threaded pre-load adjustment and external compression adjustment knob allow for fine tuning to provide optimum performance for every riders size and riding style. Fits 91-Up FXD/FXDWG models 690249 13.5 piggyback shock, Bronze............................... $1,199.99 690250 13.5 piggyback shock, Black................................. $1,199.99 633233 12.5 piggyback shock, Bronze............................... $1,199.99 690248 12.5 piggyback shock, Black................................. $1,199.99 Fits 04-Up XL models 633260 12 piggyback shock, Bronze................................. $1,199.99 633261 13 piggyback shock, Bronze................................. $1,199.99 SEATS & BAGS FOOT HAND LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES 970 Series Remote Reservoir Performance Shocks by Progressive Suspension High-Pressure gas charged dampers use deflective disc-valving, high-performance dampers are wrapped in a progressive rate spring with a threaded pre-load adjuster. The remote reservoirs mount in front of the saddlebags and allow for easy compression tuning. Fits all 93-13 Touring models Standard Shocks 690190 13 standard shock, Bronze..........................................$1,249.99 690192 12 standard shock, Bronze..........................................$1,249.99 Heavy-Duty Shocks 690191 13 heavy-duty shock, Bronze........................................$1,249.99 690193 12 heavy-duty shock, Bronze........................................$1,249.99 SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.37
680035 680036 Optional Compressor Kit Air Dragger Shocks by Progressive Suspension By combining a machined aluminum air chamber, velocity sensitive, multi-stage valving and an internal progressive rate coil spring, Progressive has once again elevated air suspension to a new level. The clean and simple, full chrome body mounts to all 80-13 Touring models integrates with existing Schrader valve or can be powered by a clever compressor unit that uses a hook and loop style fastener to mount into the back of a saddlebag. Effortless installation, up to 2 inches of on-the-fly height adjustment and an economical price is a hard to beat combination! 680035 Air Dragger shocks for 80-14 Touring models...........$498.99 680036 Air Dragger easy mount compressor kit................$489.99 American Tuned Covered Gas Shocks with TÜV by Progressive Suspension Progressive s popular Model 412 with full-length covers, double-wall construction and 6-stage damping. Special cam adjusters permit easy preload adjustment, heat treated hard-chrome rods, long-life seals and fade-resistant oil. Upper and lower bushings are included. Sold in pairs. Note: When installing shorter-than-stock shocks, it is imperative that the fender-to-tire clearance is checked. Fit 4-Speed Big Twins from 58-86 13.5"-long shocks fit 4-speed Big Twins from 58-72, and 12"-long shocks fit 4-speed Big Twin models with rear disc brake from 73-86. 28422 13.5" eye-to-eye.................................... $358.99 28421 12.0" eye-to-eye.................................... $358.99 28578 11.0" eye-to-eye.................................... $358.99 Fit Dyna Glide Models from 91-14 Chrome 28457 11.0" eye-to-eye (standard-duty).................... $358.99 29897 11.0" eye-to-eye (heavy-duty)....................... $358.99 28458 12.0" eye-to-eye (standard-duty).................... $358.99 29899 12.0" eye-to-eye (heavy-duty)....................... $358.99 13 13.38 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL 28403 SEATS & BAGS 28425 FOOT HAND LIGHTING 412 Series Shocks by Progressive Suspension The 412 Series shocks are simply the best value shock on the market today. The 412s simple, durable design means they will be an improvement to your motorcycle's suspension performance for as long as you are riding it. The doublewall steel body construction with nitrogen charged, multi-staged velocity sensitive valving gives you smooth, consistent damping. A five-position cam style preload adjuster lets you dial in your ride whether you're a light rider or heavy hitter. With multiple options like chrome or black covers, chrome or black springs in progressive rate, Standard or Heavy-Duty for most applications, there is sure to be a 412 that's right for you and your bike. Sold in pairs. Note: When installing shocks which are shorter than the Original Equipment units that your motorcycle came equipped with, it is imperative that the fender-to-tire clearance is checked. The rates of the springs used on these shocks will accommodate most touring and riding needs. FLH/FLT Models (Standard Rate Springs) Chrome 28574 13.5 fits 80-05.................................... $299.99 28572 13 fits 80-05...................................... $299.99 28570 12.5 fits 80-05.................................... $299.99 Black 28575 13.5 fits 80-05.................................... $299.99 28573 13 fits 80-05...................................... $299.99 28571 12.5 fits 80-05.................................... $299.99 FLH/FLT Models (Heavy-Duty Rate Springs) Chrome 28957 12 fits 80-05...................................... $299.99 Black 28958 12 fits 80-05...................................... $299.99 Dyna Models (Standard Rate Springs) Chrome 28494 12.5 fits 91-Up.................................... $299.99 28469 12 fits 91-Up...................................... $299.99 28464 11 fits 91-Up...................................... $299.99 Black 29908 12.5 fits 91-Up.................................... $299.99 29904 12 fits 91-Up...................................... $299.99 29900 11 fits 91-Up...................................... $299.99 Dyna Models (Heavy-Duty Rate Springs) Chrome 29898 12 fits 91-Up...................................... $299.99 29896 11 fits 91-Up...................................... $299.99 Black 29905 12 fits 91-Up...................................... $299.99 29901 11 fits 91-Up...................................... $299.99 4-Speed FL/FX Models (Standard Rate Springs) Chrome 28430 12 fits 73-86...................................... $299.99 28423 11 fits 73-86...................................... $299.99 Sportster and FXR Models (Standard Rate Springs) Chrome 28495 14.25 fits 79-03................................... $299.99 28434 14.25 fits 52-78 K-Models & XL.................... $299.99 28433 13.5 fits 79-03.................................... $299.99 28451 13.5 fits 52-78 K-Models & XL...................... $299.99 28432 13 fits 79-03...................................... $299.99 28431 12.5 fits 79-03.................................... $299.99 28955 12 fits 79-03...................................... $299.99 680237 11.5 fits 04-Up.................................... $299.99 28429 11.5 fits 79-03.................................... $299.99 680235 11.5 fits 04-Up.................................... $299.99 28403 11.5 fits 79-03.................................... $299.99 28402 Full length chrome covers ONLY for 11 shocks........ $89.99 Black 28428 14.25 fits 79-03................................... $299.99 28425 13.5 fits 79-03.................................... $299.99 28426 13 fits 79-03...................................... $299.99 28427 12.5 fits 79-03.................................... $299.99 28956 12 fits 79-03...................................... $299.99 680236 11.5 fits 04-Up.................................... $299.99 28439 11.5 fits 79-03.................................... $299.99 680234 11.5 fits 04-Up.................................... $299.99 28401 11.5 fits 79-03.................................... $299.99 Sportster and FXR Models (Heavy-Duty Rate Springs) Chrome 28957 12 fits 79-03...................................... $299.99 Black 28958 12 fits 79-03...................................... $299.99 ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.39
Custom Chrome Shock Absorbers Springs, adjustment cam covers and eyebolts and shock covers are chrome-plated. Long-wearing, hard-chromed piston shafts. Spring preload is adjustable using standard shock tools. Cams are heat-treated and lock into place with a double-lock retaining collar. Sold in pair. Fit all 4-Speed Big Twin Models from 73-86 (except FX Softail Models) 28100 12.0" eye-to-eye without covers................................................................................................. $174.99 28101 12.0" eye-to-eye with covers.................................................................................................... $199.99 28145 11.0" eye-to-eye without covers................................................................................................. $159.99 28146 11.0" eye-to-eye with covers.................................................................................................... $179.99 Note: When installing shorter-than-stock shocks, it is imperative that the fender-to-tire clearance is checked. Fit all 4-Speed Big Twin Models from 58-72 28089 13.5" eye-to-eye without covers................................................................................................. $186.99 28099 13.5" eye-to-eye with covers.................................................................................................... $190.99 13 13.40 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL SEATS & BAGS 670727 FOOT HAND LIGHTING ELECTRICAL EXHAUST 670726 INTAKE 670728 ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES Fully Adjustable Dyna Shocks by TTM Ted Tine, original designer of the adjustable ride height performance series shock absorbers, has created the ultimate in high performance precision suspension systems. Their advanced technology enhances handling and traction and brings world class performance to your motorcycle. Oil pneumatic gas injection Double adjustable Spring preload adjustment Rebound adjustment Show chromed steel bod Also available with 1 ride height adjustment 670724 Fits FXD 91-Up, rebound adjustable, with cover 13.5...$569.99 670726 Fits FXD 91up, no cover, preload adjustment only 13...$569.99 High Performance FXR/XL Shocks by TTM Ted Tine, original designer of the adjustable ride height performance series shock absorbers, has created the ultimate in high performance precision suspension systems. Their advanced technology enhances handling and traction and brings world class performance to your motorcycle. 1 adjustable ride height With or without cover Oil pneumatic gas injection Show chromed steel body Preload adjustable 670727 Fits FXR 82-94 and XL 91-03 with cover 11.5........ $569.99 670728 Fits FXR 82-94 and XL 91-03 without cover 11.5..... $569.99 SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.41
680131 680039 Slammer Lowering Kits by Burly Complete lowering kit in one box Easy to install, Fork springs DO NOT require complete disassembly of forks! Custom short rear shocks lower rear up to 2.5" Drop thru in fork springs lower front end up to 2" 688967 Fits Touring Models 680042 Fits 80-13 Touring models, Chrome.............................................................................................. $339.99 Fits Softail Models 688968 Fits 00-14 Softail models (except FXCW /C Models), Chrome........................................................................ $172.99 688967 Fits 84-99 Softail models, Chrome............................................................................................... $172.99 Fits Dyna Models 680041 Fits 06-14 Dyna models, Chrome................................................................................................. $339.99 690200 Fits 06-14 Dyna models, Black................................................................................................... $299.99 680040 Fits 91-05 Dyna models, Chrome................................................................................................. $339.99 Fits Sportster Models 680039 Fits 04-14 Sportster models, Chrome............................................................................................. $339.99 680131 Fits 04-14 Sportster models, Black............................................................................................... $339.99 680038 Fits 88-03 Sportster models, Chrome............................................................................................. $339.99 13 693901 693902 Burly Brand Slammer Shocks Measures a stubby 10.5 in. eye-to-eye Preload adjustable to tune to rider weight Available in black or chrome Made in the U.S.A. Fits Sportster Models 693901 Chrome, Burly Slammer shocks for 88-03 XL models............... $219.99 693902 Black, Burly Slammer shocks for 88-03 XL models.................. $219.99 693903 Chrome, Burly Slammer shocks for 04-14 XL models............... $219.99 693904 Black, Burly Slammer shocks for 04-14 XL models.................. $219.99 Fits Dyna Models 693905 Chrome, Burly Slammer shocks for 91-14 Dyna models............. $219.99 693906 Black, Burly Slammer shocks for 91-14 Dyna models............... $219.99 Fits Touring Models 688960 Chrome, Burly Slammer shocks for 80-14 Touring models........... $219.99 13.42 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL SEATS & BAGS FOOT Adjustable Lowering Kit for Twin Cam 88 Softail Models by Wild 1 Adjustable for ride height through a range of nearly 2-inches, this trick part from Wild 1 gets your bike lower! 19206 Fits all Softail models from 00-14.................... $68.99 HAND LIGHTING ELECTRICAL EXHAUST Rear Struts These were what we used back in the old days to convert swingarm frames to rigid. Simply remove your shocks and replace with the struts. Available to fit early Big Twins & Sportsters as noted. Made in USA by Paughco. Sold in pairs 632260 12" struts with 5/8" holes for early B/Twin & 57-74 XL's...$85.99 632261 12" struts with 1/2" holes for late B/Twin & 75-78 XL's....$85.99 632262 11" struts with 1/2" holes for late B/Twin & 75-78 XL's....$85.99 Wild 1 Adjustable Lowering Kit for Softail Models Adjustable spherical rod ends permit simple ride height control. 19279 Fits all Softail models from 89-99..................... $89.99 INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES SHEETMETAL Chrome Lowering Kit for Twin Cam Softail Models Adjustable mounts install on the Original Equipment and Progressive Suspension Softail shocks. Permits the bike to be lowered up to two full inches, improving the look by closing the gap between the tire and fender. Sold in pairs. 29806 Fits all Softail models from 00-14.................. $119.99 INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.43
28528 Burly Adjust-A-Ride Kits for Softail Models Fully adjustable versions of the popular Lowboy lowering kits which don t require any cutting, grinding, or irreversible modifications and can be installed in an hour. Permits the ride height to be adjusted up to 2" lower or raised from the stock height by 1/2" in minutes with a 3/4" wrench. They feature sealed heim joint bearings that require very little maintenance. Fits all Softail Models from 84-88 Fit Original Equipment shocks only. 28477 Plain.................................... $99.99 Fits all Softail Models from 89-99 Also fit the American Tuned gas shocks from Progressive Suspension, Inc. 28478 Plain.................................... $99.99 Burly Rear Lowering Kits Bolt-on shock mounts that move shock mounting points further back and down, lowering the rear of your bike approximately 1" with no loss of wheel travel. Installation is easy, with no permanent modifications to your bike. All kits come with a black powdercoated finish and include instructions and all necessary hardware. For Touring Models 640374 Fits all models from 02-08 (except FLHX and FLH RS)................ $119.99 641272 Fits all models from 09-14 (except FLHX, FLHXI, FLHRS models)....... $129.99 28528 Fits all models from 97-01 (except 98-01 Classic models), Black....... $105.99 28479 Fits all models from 85-96, Black................................... $105.99 For Dyna Glide Models 640375 Fits 02-14 models................................................ $129.99 07912 Fits all models 00-01.............................................. $119.99 07911 Fits all models from 91-99 (except FXDL and FXD Convertible with Original Equipment saddlebags), Black..................................... $109.99 For Sportster Models 640381 Fits all 05-14 models (except Low and Custom models).............. $109.99 688962 Fits all 04 models (except Custom and Hugger models)............... $89.99 07898 Fits all models from 00-03 (except Custom and Hugger models)....... $79.99 28522 Fits all models from 86-96 (except Custom and Hugger models)...... $104.99 Note: These lowering kits are not recommended to be installed on motorcycles equipped with lowered shocks. Lowering your motorcycle will reduce cornering clearance. This modification is intended for custom motorcycles. It is not recommended for motorcycles ridden on the streets or highways. All Burly lowering kits are made in the USA. 13 Adjustable Rear Shock Lowering Kits For Touring Models This adjustable rear shock lowering kit are engineered to lower the rear of your motorcycle up to 3 lower than stock. There are three 1 adjustment locations. Fully adjustable to get the exact ride height you want. Give your bike a tough, custom stance. Black powder coated harden steel construction. Includes all necessary hardware and instructions. Sold in pairs. 631427 Fits Touring models 02-Up (Except FLHX, FLHRS & FLHRC Road King models with stock OEM leather bags)............................ $30.99 Note: Lowering your motorcycle reduces cornering clearance. It is not recommended to use this kit with lowered shocks. Check all clearances after installing this kit. Ness-Tech Lowering Kits for Softail Models Lowers the rear of Softail models up to two inches. Includes replacement shock studs, hardware and blue Loctite. 05992 Fits all Softail models from 00-14................................... $69.99 13.44 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
631426 APPAREL SEATS & BAGS FOOT HAND LIGHTING 631424 631422 ELECTRICAL 631425 EXHAUST INTAKE ENGINE 631421 631423 631420 GASKETS TRANSMISSION & CLUTCH DRIVELINE Rear Lowering Kits by Custom Chrome Give your bike the low aggressive look you ve always wanted and plant your feet safely on the ground. Sold in sets. Simple easy installation with no modifications Include hardware and instructions Lowers the bike 1 to 1.5 depending on application Kits for 02-13 Touring models will not work on models with OEM Leather bags 631420 1 lowering kit for Dyna Glide models 06-14.................................................................................... $85.99 631421 1.5 lowering kit for Dyna Glide models 95-05................................................................................... $85.99 631422 Adjustable lowering kit for Softail models 00-14................................................................................. $34.99 631423 1 lowering kit for Sportster models 05-Up...................................................................................... $85.99 631424 1 lowering kit for Sportster models 00-04...................................................................................... $85.99 631425 1 lowering kit for Touring models 02-Up (except FLHX, FLHRS & FLHRC).......................................................... $90.99 631426 1 lowering kit for Touring models 97-01 (except FLHX, FLHRS & FLHRC)1 lowering kit for Touring models 02-Up (except FLHX, FLHRS & FLHRC)1 lowering kit for Touring models 97-01 (except FLHX, FLHRS & FLHRC).................................................... $90.99 Note: Lowering your motorcycle reduces cornering clearance. It is not recommended to use these kits with lowered shocks. Check all clearances after installing these kits. WHEELS TIRES & BRAKES SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.45
28178 28171 28175 28174 Lower Shock Stud Kits Each kit includes a stud, chrome washers, rubber bushings, spacer and chrome nuts. Sold each. 28178 Fits FL models, 58-66 (repl. OEM 54517-58)..............$13.99 28171 Fits FL and FX models, 67-72 (repl. OEM 54517-67).......$13.99 28175 Fits 4-speed FL and FX Big Twins, 73-86 (repl. OEM 3958).$13.99 633877 Fits Sportster models, 75-78............................$13.99 28174 Fits Sportster and K models, 56-74 (repl. OEM 54516-72)..$16.99 28168 Fits Sportster models, 82-87 (repl. OEM 4081)............$23.99 28169 Fits FXR models, 82-88 (repl. OEM 1614).................$22.99 Chrome Washers (packs of 10) 220080 3/8" hole (replaces OEM 54543-65)......................$1.40 220081 1/2" hole (replaces OEM 54545-65)......................$1.40 220082 5/8" hole (replaces OEM 54544-65)......................$1.40 28168 28169 688554 28177 28170 13 Shock Stud Lock Nuts Lock nuts for shocks on FL models from 58-84, FX models from 71-86 and Sportster models from 54-78. Also used as the rear brake drum brake anchor nut on FL models from 63-72 and FX models from 71-72 (5/8"-18 threads). Replaces OEM 7993. Sold in 10 pack. 220042 Shock Stud Lock Nuts...................................$1.30 Shock Stud Kit for Big Twins Contains two lower shock stud kits and chrome nuts for the upper studs. The studs are grade 5 and zinc-plated with a locking agent applied to provide you with a secure installation. 28176 Fits 4-speed Big Twins from 73-86..........................$27.99 Rubber Shock Bushings Rubber bushings for the shock mounting studs used from 58-72. 28088 Replaces OEM 385210-42A (bag of 10).....................$1.20 28172 28173 Upper Shock Stud Kits Includes a stud, chrome washers, rubber bushings, spacer and chrome nuts. Sold each. 28177 Fits 4-speed FL models, 58-66 (repl. OEM 54515-58A)...$13.99 28170 Fits FL and FX models, 67-72 (repl. OEM 54515-57)......$13.99 28172 Fits 4-speed FL and FX models, 73-86 (repl. OEM 54515-73).....................................................$13.99 56399 Upper shock stud spacer only for FL and FX models, 67-84 (repl. OEM 5960W)................................... $2.49 28173 Fits 56-74 Sportster and K models (repl. OEM 54515-56B).....................................................$13.99 688554 Fits 94-99 Sportster, models studs and washers only (repl. OEM 47384-94)...................................... $29.99 Shock Stud Spacer Replacement upper shock stud spacer for Big Twin models from 58-99 without rear guards. (repl. OEM 5960) 220076 Pack of 10............................................ $0.90 13.46 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.
APPAREL Chrome Shock Stud Kits Kits include a chrome-plated stud, chrome washers, rubber bushings, spacer and chrome nuts. Sold each. Upper Shock Stud Kits 28192 Fits 4-speed FL and FX models, 73-86 (repl. OEM 54515-73).....................................................$19.99 28179 Fits FL and FX models, 67-72 (repl. OEM 54515-57)......$19.99 28195 Fits FL models, 58-66 (repl. OEM 54515-58A)........... $22.99 28193 Fits Sportster and K models, 56-74 (repl. OEM 54515-56B).....................................................$19.99 Lower Shock Stud Kits 28191 Fits FL and FX models, 67-72 (repl. OEM 54517-67)......$19.99 28186 Fits FL models, 58-66 (repl. OEM 54517-58)............ $22.99 28194 Fits Sportster and K models, 56-74 (repl. OEM 54516-72)................................................... $21.99 Shock Stud Covers Chrome-plated stud covers for 4-speed Big Twin and Sportster models. Sold in pairs. 26492 Fits 4-speed FL and FX models from late 70-84 and Sportster models 65-74 (repl. OEM 54704-65)................... $9.99 26489 Fits Sportster models, 75-78 (repl. OEM 54704-75T)....... $9.99 Chrome Upper Shock Covers for Sportster and FXR Models Chrome trim covers fit over the upper shock mount on Sportster and FXR models from 82-99. Sold in pairs. 220010 Fits Sportster models, 91-99 (replaces OEM 54712-94)........$12.99 220010 SEATS & BAGS FOOT HAND LIGHTING ELECTRICAL EXHAUST Shock Mounting Kits for Softail Models Upgrade the hardware when you upgrade your shocks. Mounting kits for shocks includes four shoulder bolts and washers. Fits all Softail models 84-14 repl. OEMs 4074, 6724). 28396 Chrome (set of 4)..$25.99 28399 Cadmium-plated (set of 4).................$14.99 Chrome Shock Covers These top covers fit all 4-speed Big Twins (without saddlebag guards) with stock shocks from 58-84, and 52-78 Sportster and K models. Sold in pairs. 26490 Replaces OEM 54707-84T............ $20.99 Note: Stock replacements for 52-64 Sportster and K models as well as 58-64 FL models. All other applications are custom. Some seats may cause interference. INTAKE ENGINE GASKETS TRANSMISSION & CLUTCH DRIVELINE WHEELS TIRES & BRAKES SHEETMETAL INSTRUMENTS & GAUGES GENERAL CROSS REFERENCE www.customchrome.com 13.47
680123 Progressive Suspension Gauge-Mounted Shock Absorber Pumps Perfect OEM and aftermarket air shocks, forks, and emergency tire repair Available in five styles making easy to service any low-pressure or high-pressure pneumatic systems An exclusive let-down valve allows for precise adjustments Check valve insures a no-leak operation 680123 0-30 PSI pump........................................$47.99 680124 0-60 PSI pump........................................$47.99 680125 0-100 PSI pump.......................................$47.99 Shock Adjusting Tool Fits Sportster models from 67-74, all Sportster and FXR models from 82-03, and all 4-speed FL and FX models from 58-86. 20121 Replaces OEM 94700-52B..............................$13.99 Progressive Suspension Shock Wrench Designed to adjust the spring preload on most factory-style shocks (including aftermarket). For all models (except Softail and Touring models) from 75-14 20129 Sold each.............................................$4.99 13 13.48 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity. Please see Cautionary Information in back of catalog.