JTC-1011 CRANKSHAFT PULLY HOLDER JTC-1115 BMW BUSH REMOVER / INSTALLER JTC-1123 IGNITION LOCK REMOVER For removal and replacement of the crankshaft bolt, M112 and M113, as found on E320, E430, etc. Applicable: BENZ M112, M113, M137, M155, M156, M275, M288 Removal and replacement tool for metallic bushes on rear axles. Applicable: BMW E38, E39, E53, E60, E61, E 63, E64, E65, E66, E67, E70, F01, F02, F04, F07, F10, F11, and F18. For removal and replacement of the ignition switch retaining ring fitted to Mercedes types W129, W140, W202, W210, W220, W203, W209, W211, W204.
JTC-1124 WHEEL STUD ALIGNMENT GUIDE TOOL (M14) JTC-1215 BMW REAR AXLES BUSH REMOVER / INSTALLER JTC-1231 MB TRANSMISSION DIPSTICK (722.6) Assists when mounting wheels, especially late models with long lug bolts. Size: M14 x 1.5 Applicable: All Mercedes models with lug bolts. Removal and replacement tool for metallic bushes on rear axles BMW type E36, E46. Replacement of the mounting bushes without removing the complete rear axle assembly. Applicable: BMW E36, E46, E85 The tool is designed to measure the oil level of transmission. Full length: 1220mm Applicable: transmission type 722.6
JTC-1232 MB TRANSMISSION DIPSTICK (722.7, 716.5, 722.8) The tool is designed to measure the oil level of transmission. Full length: 920mm Applicable: transmission type 722.7, 716.5, 722.8 JTC-1233 MB TRANSMISSION DIPSTICK (STRAIGHT END) Full length: 930mm, balance the top of the oil gauge. Applicable: Engine model: 103, 943/984/985, 104, 111, 119, 120, 137, 603, 913/963/97, 604, 605, 606, 611, 612, 613, and 626. JTC-1234 MB TRANSMISSION DIPSTICK (VOLUTE END) Full length: 930mm, the top of the oil gauge can turn back to 90 degrees. Applicable: Engine model: 112, 113, 646, 647, and 648.
JTC-1306 BENZ SUB-FRAME BUSH REMOVER / INSTALLER Special design for removing and installing the frame on the car. Applicable: W211, W220, W203 JTC-1307 BENZ SEAL TOP AIR SUSPENSION STRUT Special design to remove the seal cap easily and replace the seal quickly. Applicable: W220 JTC-1308 SPARK PLUG ELECTRIC WIRE REMOVER FOR BENZ V6 Special angle with 17mm wrench to be a lever for removing and installing the wire easily. Applicable: BENZ engine models V6.
JTC-1309 BMW CAMSHAFT ALIGNMENT TOOL JTC-1313 FAN CLUTCH TOOLS SET JTC-1331 BENZ CAMSHAFT ALIGNMENT TOOL Use with JTC-1807 to fix on the camshaft. Contents: JTC-1701, 1702, 1703, 1713, Holds the camshaft at 40 degrees. TDC Special design for using before installing the 1714, 1715, 1832 position (left / right side) accurate engine. Applicable: BMW engine models M52TW, Application: Most of Mercedes, BENZ, and BMW vehicles. Applications: BENZ M111, M119. M54, and M56.
JTC-1332 BENZ CAMSHAFT ALIGNMENT TOOL JTC-1338 BENZ STRUT NUT SOCKET(S) W220 JTC-1339 BENZ STRUT NUT SOCKET (C) W203 Holds the camshaft at 40 degrees. TDC Use for removing and installing the top Use for removing and installing the top position (left / right side) shock retaining nut. shock retaining nut. Applications: BENZ M112, M113. Applications: BENZ W220 The function is same as #1338. Applications: BENZ W203
JTC-1415 BENZ ML BALL JOINT SOCKET Pin wrench socket 3/4" drive, to secure retaining ring for ball joint replacement. Applicable: 163 M-Class front and rear axles Retaining ring is torqued to 300 Nm / 226 ft. / lbs. JTC-1419 BMW REAR SUB-FRAME DIFFERENTIAL BUSH EXTRACTOR / INSTALLER To extract and install the rear sub frame and differential bush. Applicable: BMW E46, E85 JTC-1420 BENZ TRANSMISSION OVERFLOW PIPE REMOVER Drift for unclipping the overflow pipe in the oil pan when draining the oil. Applicable: BENZ 722.9 model transmission.
JTC-1433 BMW SPROCKET EXTRACTOR / INSTALLER For turning sprockets when removing and installing vanos unit. Applicable: BMW m50 / m52 / s50 / s52 JTC-1533 CRANKSHAFT PULLY HOLDER (M271) For removal and replacement of the crankshaft bolt. Applications: BENZ M271 JTC-1549 BENZ STEERING TORQUE ROD JOINT INSTALLER / REMOVER Application: W171, W203, W209 Special design with self locking nut to remove and install the torque strut at front axle. Bore size: M14 x 1.5
JTC-1550 BENZ / BMW FUEL TANK LID WRENCH The tool is designed to remove the plastic fuel tank lid. Applicable: o BMW: MODEL 211 / 203 o BMW: E36, E46 JTC-1552 BENZ SUB-FRAME BUSH INSTALLER / REMOVER (ML) Removal and replacement tool for metallic bushes on rear axles. Applicable: BENZ W164 JTC-1556 BMW REAR SUB-FRAME DIFFERENTAL END BUSH INSTALLER / REMOVER On car maintenance. For replacement of the rear suspension deferential bush. Applicable: BMW E46, E85
JTC-1701 FAN CLUTCH TOOLS (32mm) JTC-1702 FAN CLUTCH TOOLS (36mm) JTC-1703 FAN CLUTCH HOLDER Removes lock nuts on the thermo-viscous fans found on Ford, BMW, etc. Length: 380mm Size: 32mm Removes lock nuts thermo-viscous fans found on Ford, Mercedes, etc. Made from tempered pressed steel. Allow the technician to hold the water pump pulley in place while loosening the radiator fan. BMW engine models M10, M20, & M30, and late cars.
JTC-1712 GUIDE RAIL PIN PULLER JTC-1713 FAN CLUTCH HOLDER L TYPE JTC-1714 FAN CLUTCH HOLDER 3 HOLES Can remove even the most stubborn pins from the cylinder head, unlike the short slide hammer previously used to attempt this job. Applicable: Model M102, 110, 115, 116, 117, 130, OM601, 602, 603, 615, 616, 617 Used for R & R viscous fan coupling with radiator in place. Specially designed 3 holes to hold the stud on fan clutch assembly found on Mercedes BENZ vehicles to allow release of lick out. Slim handle for tight space operation.
JTC-1725 DASHBOARD SERVICE TOOL KIT JTC-1801 BENZ SPRING COMPRESSOR JTC-1807 BMW CAMSHAFT ALIGNMENT TOOL - M50 Kit includes ignition lock remover, radio set remover, and instrument cluster removing hooks. Suitable for most Mercedes BENZ series. Types: 116/ 123 / 124 / 126 / 129 / 140 / 201 / 202 and 4-matic include. Advantage: Newly developed automatic 3-point safety interlock and automatic freewheel at the end of stroke. Includes: 2 blocks, swivel lock & locking pin, for setting camshaft timing. Applicable: BMW engine models M42 & M50.
JTC-1808 BMW CAMSHAFT ALIGNMENT TOOL - M60 JTC-1832 FAN BELT SERVICE WRENCH JTC-1837 BUSH REMOVER / INSTALLER Includes: 2 blocks, swivel lock & locking pin, for setting camshaft timing. Applicable: BMW engine models M60 & M62. This universal tool has been designed service Mercedes Benz, Nissan Quest, Mercury Villager Radiator fans and pulley belts. This special wrench can be used for loosening the A/C idler pulley tension lock-nut for A/C belt adjustment or replacement. 8 m/m & 10 m/m bit included. Removal and replacement tool for metallic bushes on rear axles. Applicable: W140, W124, W201, W202, W129, W210, 220
JTC-1842 BMW GUIDE RAIL PIN OULLER JTC-1844 FUEL TANK LID WRENCH-210 JTC-1851 FUEL TANK CUP WRENCH-202 Can remove even the most stubborn pins from the cylinder head, unlike the short slide hammer previously used to attempt this job. This puller incorporates a thrust bearing to easy the pulling action. The tool is designed to remove the plastic fuel tank lid. Applicable: W210 The tool is designed to remove the plastic fuel tank lid. Applicable: W202
JTC-1852 BRAKE SPRING INSTALLER JTC-1853 WHEEL STUD ALIGNMENT GUIDE TOOL (M12) JTC-1858 BMW BUSH EXTRACTOR For pressure spring of packing brake. Applicable: All Mercedes models. Assists when mounting wheels, especially late models with long lug bolts. Size: M12 x 1.5 Applicable: All Mercedes models with lug bolts. Used for R & R of rear wheel bearing located in wheel carrier. Applicable: E36, E30, E46
JTC-4005 BMW CAMBER ADJUSTING TOOL (E60) JTC-4006 BMW CAMBER ADJUSTER (E38) JTC-4028 BMW A/C COMPRESSOR CLUTCH REMOVER Use to adjust front camber. Applicable: BMW E60, E61, E63, E64 Use this fixture to adjust the front camber on late model 3 series. Applicable:BMW E38, E39, E46, E53, E65, E66, E67, E81, E83, E85, E86, E87, E90, E91, E92, E93 To remove the plate of clutch on BMW. Applicable: Most BMW cars. Size: M26 X P1.5
JTC-4046 OIL FILTER WRENCH (46mm) JTC-4047 BENZ ALIGNMENT TOOL SET (M275) JTC-4048 BMW STRENGTHEN BUSH INSTALLER TOOL The special socket is suitable for the operation of the filter housing cap when replacing the AD blue filter on MERCEDES-BENZ commercial vehicles with blue TEC engines. Suitable for these vehicles: ACTROS, ATEGO, AXOR, ECONIC This retaining device is designed for positioning the camshaft in 30 degree TDC position. Applicable: o M275, M285: The set C only used for left bank of cylinder and set A & B used for right bank. o M137: Use the set A&B to loosen and tighten mounting screws for the camshaft sprocket and adjusting the timing. Special designed tool to compress the strengthen bush before stalling into subframe. Use with JTC-4820 or another install tool Applicable: BMW E87, E90, E92, E93
JTC-4059 BMW CRANKSHAFT ROTATING TOOL Special designed to rotate the BMW diesel engine crankshaft. Applicable: o 2.5D: M57N256D2 o 3.0D: M57306D3, M5736D5, M57D30A, M57N206D3, M57N2306D3, M57N306D2, M57N306D3, M57N306D5, N57N306D2, N57N306D3 JTC-4060 BMW FLYWHEEL LOCKING TOOL (M112) Used to fix the flywheel gear to remove & install crankshaft pulley centre bolt. Applicable: BENZ M112, M113, M137, M155, M156, M272, M273 JTC-4096 BMW SUSPENSION BUSH EXTRACTOR / INSTALLER (E39) Operation on car. Extractor for replacement of the rear suspension mounting bushes. Replacement of the mounting bush without completely lowering the rear axle assembly. Applicable: BMW E39
JTC-4097 BMW SUSPENSION BUSH EXTRACTOR / INSTALLER (E53) Operation on car. Extractor for replacement of the rear suspension mounting bushes. Replacement of the mounting bush without completely lowering the rear axle assembly. Applicable: BMW E53 JTC-4101 BENZ SUB-FRAME BUSH INSTALLER / REMOVER (WW221) Removal and installation of rear mounts of axle suspension. Applicable: BENZ W216, W221, W222 MM number: 221589004300, 221589034300 JTC-4110 BENZ FUEL TANK LID WRENCH (W164) The tool is designed to remove the plastic fuel tank lid. Applicable: BENZ W164, W251 MM number: 164589010700
JTC-4111 BMW, VOLVO FUEL TANK LID REMOVER JTC-4114 BENZ FLYWHEEL LOCKING TOOL (M166) JTC-4117 BMW N63 TIMING TOOL SET Special designed to remove fuel tank lid for diesel and petrol cars. Applicable: o BMW: F01, F02, F10, F12 o VOLVO: T4, T5 engine, 2010 later Used to fix the flywheel gear to remove & install crankshaft pulley centre bolt. Applicable: BENZ: o A class W169 (M166) o B class W245 (M266, OM640) MM number: 166589004000 Special designed to located and turn the camshaft in correct TDC position. The 4117 7 holding tool is designed to hold the camshaft pulley for turning the central bolt. Applicable: BMW N63 engine