Siteline EX Clad Double-Hung Windows Premium Wood

TABL OF CONTNTS Specifications... 5-2 QuickSpecGuide... 5-4 levations:1/4 Scale... 5-6 Double-Hung... 5-9 Double-Hung Picture... 5-16 Double-Hung Picture with Flankers... 5-26 SectorTop... 5-28 FullRadius... 5-33 Transoms... 5-34 SashGlazingOptions:3 Scale... 5-36 TrimOptions:3 Scale... 5-37 JambOptions:3 Scale... 5-39 Standard Mullion Options... 5-40 LiteCutInformation... 5-42 ClearOpeningandDaylightSpecifications... 5-44 Unit Sizing, Rough Openings & Masonry Openings... 5-58 SectionDetails:6 Scale... 5-60 Angle Bay Specification and Rough Opening Information... 5-72 SectionDetails:3 Scale(AngleBay)... 5-74 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-1

XTRIOR FINISH xterior aluminum surfaces are low maintenance extruded aluminum coated with a thermo set polyester finish that meets or exceeds the AAMA 2603 performance standards. Standard colors include Brilliant White, Chestnut Bronze, Desert Sand, French Vanilla, Hartford Green, Mesa Red, Black, Arctic Silver and Dark Chocolate. AURALAST R WOOD AuraLast R wood is fundamentally different from wood resulting from traditional millwork preservation processes in that it uses a proprietary vacuum/pressure process to provide protection throughout the wood parts used to make windows and doors. AuraLast R wood is distinguished from wood using the current preservation methods by its unique ability to achieve greater penetration of the active ingredients into the wood parts, with a penetration of the treatment being a minimum of 92%. INTRIOR FINISH All interior surfaces are unfinished clear pine ready for on site finishing. Primed and pre-finished interiors are available in paint: Pure White, xtra White, Natural Choice, Moderate White; in stain: Wheat, Cherry, Cordovan; and Clear Lacquer. FRAM Frame is assembled from select kiln dried pine using AuraLast R wood on all exterior parts. xterior surface is covered with.050 (1.27mm) extruded aluminum cladding. Frame corners at head are mechanically fastened over a silicone injected nylon corner key. Sill corner joints are tightly sealed with a foam gasket and reinforced with screw boss construction. Frame thickness is 11/16 (17.5mm) at head, side jamb and sill. Basic jamb width is 4-9/16 (116mm) and may be extended for different wall depths. Integral nailing fin is part of extrusion on all four sides. Assembled frame includes all weather-stripping and hardware installed. xterior of frame extrusion is grooved to accept accessories. SASH Sash is 1-7/16 (36.5mm) thick and combines an extruded aluminum exterior with select kiln-dried pine using AuraLast R wood. Corner joints are mortise and tenoned, machine clamped for squareness and secured with metal fasteners. xterior surfaces are covered with.045 (1.2mm) extruded aluminum, corners are clamped and sealed with silicone. Sash operate in a non-compression ivory colored jamb liner that allows both top and bottom sash to tilt inside for easy cleaning and removal without the use of tools. No finger plow sash available on venting units. GLAZING 3/4 (19mm) thick sealed insulating glass is constructed from two panes of glass, utilizing a continuous roll formed stainless steel spacer with dual seal sealant. The glass is mounted into the sash using a silicone-glazing compound and secured with interior applied profiled wood stops. All insulating glass units comply with the performance requirements of IGCC in accordance with either ASTM 774 or 2190. GLAZING OPTIONS 3/4 insulating glass available in Low- with Argon, Low-, Low- 366, Clear, Neat Glass, reflective, tinted, or obscure, tempered or other specialty glass as specified. Preserve film is a 0.003 thick polyethylene film with a low tack acrylic adhesive applied to the glass for protection during shipping and installation. 4,000 foot elevations and higher require a capillary tube to equalize environmental stress (otherwise known as High Altitude glazing). High Altitude glazing does not allow the use of Argon as listed under glazing options. Siteline X Clad Double-Hung Windows PRODUCT SPCIFICATIONS WATHR-STRIPPING ngineered system combines PVC ivory jamb liner with dual bulb weather-stripping at head. Checkrail features thermoplastic rubber bulb and recessed cam action sash lock for secure closure. Rigid vinyl water stops at sill provide additional restraint against weather. HARDWAR Sash operate by means of a dual block and tackle balance system with nylon roller pulleys and high-tension coil springs. Balance system gauged to sash weight and uses pre-stretched dacron cords attached to clutch mechanisms to insure smooth, operation and compliance with operating force requirements. Jamb liners are Ivory (White is optional). Recessed cam action sash lock is available in White, Chestnut Bronze, Desert Sand or optional Bright Brass, Antique Brass, Polished Brass, Brushed Chrome or Imitation Oil Rubbed Bronze. 28 glass width and larger units have two sash locks. Optional Lexan sash lift available for no finger plow sash. XTRIOR INSCT SCRNS Charcoal fiberglass screen cloth (18x16 mesh) set in painted roll formed aluminum frame with color to match cladding - choice of Brilliant White, Chestnut Bronze, Desert Sand, French Vanilla, Hartford Green, Mesa Red, Black, Arctic Silver or Dark Chocolate, installed in channel on frame extrusion and held in place with spring loaded plungers at the top and sides of screen. Aluminum mesh and Phantom screen also available. Insect screens are intended to allow air and light in and to keep insects out. They are not intended to keep anyone or anything from falling through an open window. For safety screens or other security devices contact your local building supply retailer. GRILLS SDL (Simulated Divided Lites) - extruded aluminum muntins permanently applied to the exterior of the insulating glass unit (not available on textured glass) in 7/8 (22mm), 1-1/8 (28.5mm), or 1-3/8 (34.9mm) widths. SDL is standard with a light bronze internal shadow bar to give a true divided lite appearance. As an option, SDL may be ordered with a silver shadow bar. Clear wood interior muntin bars match the exterior muntin width and are permanently bonded to the interior of the glass. Also available is a 2-5/16 (59mm) SDL bar, which simulates a double-hung checkrail. Full Surround Wood Grilles - Rectangular unfinished clear pine wood grilles in 7/8 (22mm) are available in patterns selected by the owner. GBG (Grilles between the Glass) - 5/8 (15.9mm) flat and 23/32 or 1 contour mounted between the glass panes suspended within the air cavity. XTRIOR TRIM 1-5/8 (41mm) wide aluminum brickmould or Adams casing with an integral nailing fin is available factory applied. Also available is 3- (88.5mm) flat casing with an integral nailing fin. All of the accessories are.050 (1.3mm) extruded aluminum. Two sizes of frame expander, 1-7/8 (48mm) and 3-1/4 (83mm) may be used alone or in conjunction with a 2-1/8 (54mm) mull expander. Standard 5/16 (8mm) clad mull cover used for joining windows together. Windows may also be joined with 1 (25.4mm), 2 (51mm), or 4 (102mm) mull covers. Color and finish match exterior finish specs above. Continued on next page October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-2

XTNSION JAMBS xtension jambs are factory applied to the interior on all four sides of the frame and are 4/4 standard thick pine to accommodate wall depths up to 9-5/16 with one piece, and up to 12 with two pieces. 9/16 (14.2mm) option also available. INSTALLATION Installation per JLD-WN Installation Method for Metal Clad Windows JII002 or JII013. See www.jeld-wen.com/resources for instructions. Siteline X Clad Double-Hung Windows PRODUCT SPCIFICATIONS PRFORMANC NFRC Certified - (Rated and labeled in accordance with NFRC) WDMA Hallmark Certified - In accordance with AAMA/NWWDA/101/I.S.2-97 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-3

SPCIFICATION XTRIOR FINISH S Brilliant White S Chestnut Bronze S Desert Sand S French Vanilla S Mesa Red XTRIOR TRIM S Nailing Fin S Drip Cap Siteline X Clad Double-Hung Windows STANDARD FATURS QUICK SPC GUID S S S S Hartford Green Black Arctic Silver Dark Chocolate INTRIOR FINISH S Natural S Priming Available S S S OPTIONAL FATURS Some options may require additional lead times. Consult your JLD-WN Sales Representative. Aluminum 1-5/8 Brickmould with integral nailing fin 3- Flat Casing with integral nailing fin Adams Clad Brickmould with integral nailing fin SIZ S Width: Venting Double-Hung: 21-3/8, 25-3/8, 29-3/8, 31-3/8, 33-3/8, 37-3/8, 41-3/8, 45-3/8 Picture Double-Hung: 21-3/8, 25-3/8, 29-3/8, 31-3/8, 33-3/8, 37-3/8, 41-3/8, 45-3/8, 49-3/8, 53-3/8, 61-3/8, 69-3/8, 77-3/8 Pre-finished Interior Options are: S Paint - Pure White, xtra White, Natural Choice, Moderate White S Stain - Wheat, Fruitwood, Cherry, Cordovan S Clear Lacquer S Width: Venting Double-Hung: Minimum: 16 Maximum: 45-3/8 Picture Double-Hung: Minimum: 16 Maximum: 77-3/8 Fixed Units over 49-3/8 wide can be up to 80 high Fixed Units up to 49-3/8 wide can be up to 92 high S : Venting Double-Hung: 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 88, 92 S : Venting Double-Hung: Minimum: 28 Maximum: 92 * * glass can t exceed 42 high Picture Double-Hung: 15, 18, 24, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 88, 92 Picture Double-Hung: Minimum: 15 Maximum: 92 Fixed Units over 49-3/8 wide can be up to 80 high Fixed Units up to 49-3/8 wide can be up to 92 high S For RO, add 3/4 S For RO, add 3/4 GLAZING S Low- Insulating Glass S Preserve Protective Film S Clear S Obscure S Bronze S Low- 366 S S S Neat Glass Reflective Tempered S High Altitude Continued on next page October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-4

QUICK SPC GUID SPCIFICATION STANDARD FATURS OPTIONAL FATURS Some options may require additional lead times. Consult your JLD-WN Sales Representative. GRILLS S 5/8 Flat, 23/32 or 1 Contour GBG S 7/8 Full Surround Wood Grilles SDL Bead Profile: S 7/8, 1-1/8, 1-3/8, 2-5/16 with Light Bronze Shadow Bar S 7/8, 1-1/8, 1-3/8, 2-5/16 with Silver Shadow Bar HARDWAR S Balance: Dual Block and Tackle S Cam Locks S Ivory Jamb Liners (standard) HARDWAR COLOR S White S Desert Sand S Chestnut Bronze S S S S White Antique Brass Polished Brass Brushed Chrome JAMB S 4-9/16 S Minimum: 4-9/16 S Maximum: 9-5/16 (one piece) S Maximum: 12 (two piece) S Imitation Oil Rubbed Bronze SCRNS S Fiberglass S Aluminum Mesh available S Phantom Screen - some size limitations apply SCRN FRAM COLOR S Brilliant White S Chestnut Bronze S Desert Sand S French Vanilla S Mesa Red S S S S Hartford Green Black Arctic Silver Dark Chocolate October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-5

GNRAL INFORMATION DOUBL-HUNG DIMNSIONAL WINDOWS Clad double-hung windows may be specified as dimensional by adjusting the the desired rough opening width or height in 1/4 increments from standard. Clad double-hung windows feature fully operating upper and lower sash. Counterbalancing is achieved with block and tackle spring extension systems hidden in weatherable PVC jambliners. Operating units are supplied with cam-type sash locks installed. Die-cast lower sash lifts supplied for field installation are an option. Recessed sash retainers provide simple sash installation and removal. There are several hardware finish options. Refer to the Specifications for available finish options. MULTIPL ASSMBLIS Clad double-hung windows may be mulled beside other clad double-hungs or clad picture windows, or below clad transom windows, to fulfill a wide variety of needs. Factory assembled mulls are limited in height (100 ), width (114 ), and a total area (75 square feet). October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-6

HANDING & OPRATION DOUBL-HUNG DOUBL-HUNG OPRATION: When the sash are locked at the check rails the sash are closed and sealed in the sash opening of the frame. When the sash are unlocked the lower sash travels vertically to any position desired. The upper sash can also be positioned as desired. SASH TILTING FOR WASHING The Custom Double-Hung window will allow the sash to be tilted or removed for easy cleaning. October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-7

LVATION NOTS DOUBL-HUNG LVATION DRAWINGS UTILIZ A LIMITD NUMBR OF PROJCTD LINS TO PRODUC A RUDIMNTARY DRAWING INTNDD TO B USD IN A SMALL GRAPHICAL SCAL. LVATIONS AR VIWD PRPNDICULAR FROM TH XTRIOR OF TH STRUCTUR. IF MOR DIMNSIONS AR NDD, US TH SCTION DRAWINGS FOR MOR COMPLT DPICTIONS. M.O. Brickmould M.O. Adams/Flat Casing Rough Opening Frame Size Daylight Opening 24 7/8 (632) 27 7/8 (708) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) Masonry Openings for Brickmould, Flat & Adams Casing. Vertical measurements include sillnose. (Subtract from Masonry Opening for Unit Size) 42 5/16 (1075) 43 13/16 (1113) 40 3/4 (1035) 40 (1016) 15 1/16 (383)[2] OUTSID OF FRAM DAYLIGHT OPNING CD2140 COTTAG STYL WINDOWS BOOK CODS UNIT WIDTH CD2168C UNIT HIGHT C = COTTAG CD INDICATS SITLIN X CLAD DOUBL-HUNG TH FIRST TWO NUMBRS INDICAT TH UNIT WIDTH BOOK COD TH LAST TWO NUMBRS INDICAT TH UNIT HIGHT GNRAL DOUBL-HUNG NOTS LVATION SYMBOL LGND: 1. ALL UNITS SHOWN AR AVAILABL AS OPRATORS ONLY. 2. UNIT LVATIONS AR SHOWN WITHOUT XTRIOR TRIM. 3. ALL OPRATING SASH AR INSTALLD WITH VINYL JAMB LINRS AND OPRATD WITH AN INTRNAL BLOCK AND TACKL SPRING SYSTM. 4. DIMNSIONAL VALUS IN PARNTHSS AR MILLIMTR CONVRSIONS. 5. VALUS IN BRACKTS AR NUMBR OF DAYLIGHT OPNINGS. MO MASONRY OPNING October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-8

1-WID UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 24 7/8 (632) 27 7/8 (708) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) 28 7/8 (733) 31 7/8 (810) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 7/8 (835) 35 7/8 (911) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 7/8 (886) 37 7/8 (962) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 7/8 (937) 39 7/8 (1013) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 7/8 (1038) 43 7/8 (1114) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 7/8 (1140) 47 7/8 (1216) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) 34 5/16 (872) 35 13/16 (910) 32 3/4 (832) 32 (813) 11 1/16 (281)[2] CD2132 CD2532 CD2932 CD3132 CD3332 CD3732 CD4132 38 5/16 (973) 39 13/16 (1011) 36 3/4 (933) 36 (914) 13 1/16 (332)[2] CD2136 CD2536 CD2936 CD3136 CD3336 CD3736 CD4136 42 5/16 (1075) 43 13/16 (1113) 40 3/4 (1035) 40 (1016) 15 1/16 (383)[2] CD2140 CD2540 CD2940 CD3140 CD3340 CD3740 CD4140 46 5/16 (1176) 47 13/16 (1214) 44 3/4 (1137) 44 (1118) 17 1/16 (433)[2] CD2144 CD2544 CD2944 CD3144 CD3344 CD3744 CD4144 50 5/16 (1278) 51 13/16 (1316) 48 3/4 (1238) 48 (1219) 19 1/16 (484)[2] CD2148 CD2548 CD2948 CD3148 CD3348 CD3748 CD4148 54 5/16 (1380) 55 13/16 (1418) 52 3/4 (1340) 52 (1321) 21 1/16 (535)[2] CD2152 CD2552 CD2952 CD3152 CD3352 CD3752 CD4152 58 5/16 (1481) 59 13/16 (1519) 56 3/4 (1441) 56 (1422) 23 1/16 (586)[2] CD2156 CD2556 CD2956 CD3156 CD3356 CD3756 CD4156 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT BASIC UNIT CLAR OPNING XCDS 20 IN WIDTH, 24 IN HIGHT & A MINIMUM OF 5.7 SQ. FT. ##* NUMBR INDICATS STANDARD DSIGN PRSSUR (DP) RATING. ##** NUMBR INDICATS OPTIONAL DSIGN PRSSUR (DP) RATING. Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-9

1-WID UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 24 7/8 (632) 27 7/8 (708) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) 28 7/8 (733) 31 7/8 (810) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 7/8 (835) 35 7/8 (911) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 7/8 (886) 37 7/8 (962) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 7/8 (937) 39 7/8 (1013) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 7/8 (1038) 43 7/8 (1114) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 7/8 (1140) 47 7/8 (1216) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) 60 3/4 (1543) 60 (1524) CD2160 CD2560 CD2960 CD3160 CD3360 CD3760 CD4160 64 3/4 (1645) 64 (1626) CD2164 CD2564 CD2964 CD3164 CD3364 CD3764 CD4164 68 3/4 (1746) 68 (1727) CD2168 CD2568 CD2968 CD3168 CD3368 CD3768 CD4168 70 5/16 (1786) 71 13/16 (1824) 68 3/4 (1746) 68 (1727) CD2168C CD2568C CD2968C CD3168C CD3368C CD3768C CD4168C 74 5/16 (1888) 75 13/16 (1926) 72 3/4 (1848) 72 (1829) 31 1/16 (789)[2] 70 5/16 (1786) 71 13/16 (1824) 29 1/16 (738)[2] 66 5/16 (1684) 67 13/16 (1722) 27 1/16 (687)[2] 62 5/16 (1583) 63 13/16 (1621) 25 1/16 (637)[2] 35 1/16 (891) 23 1/16 (586) CD2172 CD2572 CD2972 CD3172 CD3372 CD3772 CD4172 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT BASIC UNIT CLAR OPNING XCDS 20 IN WIDTH, 24 IN HIGHT & A MINIMUM OF 5.7 SQ. FT. ##* NUMBR INDICATS STANDARD DSIGN PRSSUR (DP) RATING. ##** NUMBR INDICATS OPTIONAL DSIGN PRSSUR (DP) RATING. Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-10

1-WID UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 24 7/8 (632) 27 7/8 (708) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) 28 7/8 (733) 31 7/8 (810) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 7/8 (835) 35 7/8 (911) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 7/8 (886) 37 7/8 (962) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 7/8 (937) 39 7/8 (1013) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 7/8 (1038) 43 7/8 (1114) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 7/8 (1140) 47 7/8 (1216) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) 76 3/4 (1949) 76 (1930) CD2176 CD2576 CD2976 CD3176 CD3376 CD3776 CD4176 80 3/4 (2051) 80 (2032) CD2180 CD2580 CD2980 CD3180 CD3380 CD3780 CD4180 88 3/4 (2254) 88 (2235) CD2188 CD2588 CD2988 CD3188 CD3388 CD3788 CD4188 94 5/16 (2396) 95 13/16 (2434) 92 3/4 (2356) 92 (2337) 41 1/16 (1043)[2] 90 5/16 (2294) 91 13/16 (2332) 39 1/16 (992)[2] 82 5/16 (2091) 83 13/16 (2129) 35 1/16 (891)[2] 78 5/16 (1989) 79 13/16 (2027) 33 1/16 (840)[2] CD2192 CD2592 CD2992 CD3192 CD3392 CD3792 CD4192 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT BASIC UNIT CLAR OPNING XCDS 20 IN WIDTH, 24 IN HIGHT & A MINIMUM OF 5.7 SQ. FT. ##* NUMBR INDICATS STANDARD DSIGN PRSSUR (DP) RATING. ##** NUMBR INDICATS OPTIONAL DSIGN PRSSUR (DP) RATING. Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-11

1-WID UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 7/8 (1241) 51 7/8 (1318) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 7/8 (1241) 51 7/8 (1318) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 7/8 (1241) 51 7/8 (1318) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) 34 5/16 (872) 35 13/16 (910) 32 3/4 (832) 32 (813) 11 1/16 (281)[2] 38 5/16 (973) 39 13/16 (1011) 36 3/4 (933) 36 (914) 13 1/16 (332)[2] CD4532 62 5/16 (1583) 63 13/16 (1621) 60 3/4 (1543) 60 (1524) 25 1/16 (637)[2] CD4560 78 5/16 (1989) 79 13/16 (2027) 76 3/4 (1949) 76 (1930) 33 1/16 (840)[2] CD4536 CD4576 42 5/16 (1075) 43 13/16 (1113) 46 5/16 (1176) 47 13/16 (1214) 40 3/4 (1035) 40 (1016) 44 3/4 (1137) 44 (1118) 15 1/16 (383)[2] 17 1/16 (433)[2] CD4540 CD4544 66 5/16 (1684) 67 13/16 (1722) 70 5/16 (1786) 71 13/16 (1824) 64 3/4 (1645) 64 (1626) 68 3/4 (1746) 68 (1727) 27 1/16 (687)[2] 29 1/16 (738)[2] CD4564 82 5/16 (2091) 83 13/16 (2129) 80 3/4 (2051) 80 (2032) 35 1/16 (891)[2] CD4580 50 5/16 (1278) 51 13/16 (1316) 54 5/16 (1380) 55 13/16 (1418) 48 3/4 (1238) 48 (1219) 52 3/4 (1340) 52 (1321) 19 1/16 (484)[2] 21 1/16 (535)[2] CD4548 70 5/16 (1786) 71 13/16 (1824) 68 3/4 (1746) 68 (1727) 35 1/16 (891) 23 1/16 (586) CD4568 90 5/16 (2294) 91 13/16 (2332) 88 3/4 (2254) 88 (2235) 39 1/16 (992)[2] CD4588 CD4568C CD4552 58 5/16 (1481) 59 13/16 (1519) 56 3/4 (1441) 56 (1422) 23 1/16 (586)[2] 74 5/16 (1888) 75 13/16 (1926) 72 3/4 (1848) 72 (1829) 31 1/16 (789)[2] 94 5/16 (2396) 95 13/16 (2434) 92 3/4 (2356) 92 (2337) 41 1/16 (1043)[2] CD4556 CD4572 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT BASIC UNIT CLAR OPNING XCDS 20 IN WIDTH, 24 IN HIGHT & A MINIMUM OF 5.7 SQ. FT. ##* NUMBR INDICATS STANDARD DSIGN PRSSUR (DP) RATING. ##** NUMBR INDICATS OPTIONAL DSIGN PRSSUR (DP) RATING. CD4592 Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-12

2-WID UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 46 1/4 (1175) 49 1/4 (1251) 43 (1105) 42 3/4 (1086) 14 13/16 (376)[2] 54 1/4 (1378) 57 1/4 (1454) 51 (1308) 50 3/4 (1289) 18 13/16 (478)[2] 62 1/4 (1581) 65 1/4 (1657) 59 (1511) 58 3/4 (1492) 22 13/16 (579)[2] 66 1/4 (1683) 69 1/4 (1759) 63 (1613) 62 3/4 (1594) 24 13/16 (630)[2] 70 1/4 (1784) 73 1/4 (1861) 67 (1715) 66 3/4 (1695) 26 13/16 (681)[2] 78 1/4 (1988) 81 1/4 (2064) 75 (1918) 74 3/4 (1899) 30 13/16 (783)[2] 86 1/4 (2191) 89 1/4 (2267) 83 (2121) 82 3/4 (2102) 34 13/16 (884)[2] 34 5/16 (872) 35 13/16 (910) 32 3/4 (832) 32 (813) 11 1/16 (281)[2] CD2132-2 CD2532-2 CD2932-2 CD3132-2 CD3332-2 CD3732-2 CD4132-2 38 5/16 (973) 39 13/16 (1011) 36 3/4 (933) 36 (914) 13 1/16 (332)[2] 40 3/4 (1035) 40 (1016) 15 1/16 (383)[2] 44 3/4 (1137) 44 (1118) 17 1/16 (433)[2] 48 3/4 (1238) 48 (1219) 19 1/16 (484)[2] CD2136-2 CD2536-2 CD2936-2 CD3136-2 CD3336-2 CD3736-2 CD4136-2 CD2140-2 CD2540-2 CD2940-2 CD3140-2 CD3340-2 CD3740-2 CD4140-2 CD2144-2 CD2544-2 CD2944-2 CD3144-2 CD3344-2 CD3744-2 CD4144-2 CD2148-2 CD2548-2 CD2948-2 CD3148-2 CD3348-2 CD3748-2 CD4148-2 72 3/4 (1848) 72 (1829) 31 1/16 (789)[2] 68 3/4 (1746) 68 (1727) 29 1/16 (738)[2] 64 3/4 (1645) 64 (1626) 27 1/16 (687)[2] 60 3/4 (1543) 60 (1524) 25 1/16 (637)[2] 56 3/4 (1441) 56 (1422) 23 1/16 (586)[2] 52 3/4 (1340) 52 (1321) 21 1/16 (535)[2] CD2152-2 CD2552-2 CD2952-2 CD3152-2 CD3352-2 CD3752-2 CD4152-2 CD2156-2 CD2556-2 CD2956-2 CD3156-2 CD3356-2 CD3756-2 CD4156-2 CD2160-2 CD2560-2 CD2960-2 CD3160-2 CD3360-2 CD3760-2 CD4160-2 CD2164-2 CD2564-2 CD2964-2 CD3164-2 CD3364-2 CD3764-2 CD4164-2 CD2168-2 CD2568-2 CD2968-2 CD3168-2 CD3368-2 CD3768-2 CD4168-2 74 5/16 (1888) 75 13/16 (1926) 70 5/16 (1786) 71 13/16 (1824) 66 5/16 (1684) 67 13/16 (1722) 62 5/16 (1583) 63 13/16 (1621) 42 5/16 (1075) 43 13/16 (1113) 46 5/16 (1176) 47 13/16 (1214) 50 5/16 (1278) 51 13/16 (1316) 58 5/16 (1481) 59 13/16 (1519) 54 5/16 (1380) 55 13/16 (1418) CD2172-2 CD2572-2 CD2972-2 CD3172-2 CD3372-2 CD3772-2 CD4172-2 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/8 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-13

2-WID UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 94 1/4 (2394) 97 1/4 (2470) 91 (2324) 90 3/4 (2305) 38 13/16 (986)[2] M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 94 1/4 (2394) 97 1/4 (2470) 91 (2324) 90 3/4 (2305) 38 13/16 (986)[2] 34 5/16 (872) 35 13/16 (910) 32 3/4 (832) 32 (813) 11 1/16 (281)[2] 38 5/16 (973) 39 13/16 (1011) CD4532-2 CD4536-2 CD4540-2 CD4576-2 CD4544-2 CD4580-2 CD4548-2 CD4552-2 CD4556-2 60 3/4 (1543) 60 (1524) 25 1/16 (637)[2] 56 3/4 (1441) 56 (1422) 23 1/16 (586)[2] 42 5/16 (1075) 43 13/16 (1113) 36 3/4 (933) 36 (914) 13 1/16 (332)[2] 40 3/4 (1035) 40 (1016) 15 1/16 (383)[2] 44 3/4 (1137) 44 (1118) 17 1/16 (433)[2] 52 3/4 (1340) 52 (1321) 21 1/16 (535)[2] 48 3/4 (1238) 48 (1219) 19 1/16 (484)[2] CD4560-2 64 3/4 (1645) 64 (1626) 27 1/16 (687)[2] CD4564-2 68 3/4 (1746) 68 (1727) 29 1/16 (738)[2] CD4568-2 74 5/16 (1888) 75 13/16 (1926) 72 3/4 (1848) 72 (1829) 31 1/16 (789)[2] 70 5/16 (1786) 71 13/16 (1824) 78 5/16 (1989) 79 13/16 (2027) 82 5/16 (2091) 83 13/16 (2129) 46 5/16 (1176) 47 13/16 (1214) 66 5/16 (1684) 67 13/16 (1722) 62 5/16 (1583) 63 13/16 (1621) 58 5/16 (1481) 59 13/16 (1519) 54 5/16 (1380) 55 13/16 (1418) 50 5/16 (1278) 51 13/16 (1316) 76 3/4 (1949) 76 (1930) 33 1/16 (840)[2] 80 3/4 (2051) 80 (2032) 35 1/16 (891)[2] CD4572-2 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/8 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-15

LVATION NOTS DOUBL-HUNG PICTUR LVATION DRAWINGS UTILIZ A LIMITD NUMBR OF PROJCTD LINS TO PRODUC A RUDIMNTARY DRAWING INTNDD TO B USD IN A SMALL GRAPHICAL SCAL. LVATIONS AR VIWD PRPNDICULAR FROM TH XTRIOR OF TH STRUCTUR. IF MOR DIMNSIONS AR NDD, US TH SCTION DRAWINGS FOR MOR COMPLT DPICTIONS. M.O. Brickmould M.O. Adams/Flat Casing Rough Opening Frame Size Daylight Opening 44 7/8 (1140) 47 7/8 (1216) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) Masonry Openings for Brickmould, Flat & Adams Casing. Vertical measurements include sillnose. (Subtract from Masonry Opening for Unit Size) 42 5/16 (1075) 43 13/16 (1113) 40 3/4 (1035) 40 (1016) 32 5/16 (821) DAYLIGHT OPNING OUTSID OF FRAM CDP4140 CDP INDICATS SITLIN X CLAD DOUBL-HUNG PICTUR TH FIRST TWO NUMBRS INDICAT TH UNIT WIDTH BOOK COD TH LAST TWO NUMBRS INDICAT TH UNIT HIGHT GNRAL DOUBL-HUNG PICTUR NOTS LVATION SYMBOL LGND: 1. ALL UNITS SHOWN AR AVAILABL AS STATIONARY ONLY. 2. UNIT LVATIONS AR SHOWN WITHOUT XTRIOR TRIM. 3. DIMNSIONAL VALUS IN BRACKTS AR MILLIMTR CONVRSIONS. MO MASONRY OPNING October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-16

PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 24 7/8 (632) 27 7/8 (708) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) 28 7/8 (733) 31 7/8 (810) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 7/8 (835) 35 7/8 (911) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 7/8 (886) 37 7/8 (962) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 7/8 (937) 39 7/8 (1013) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 7/8 (1038) 43 7/8 (1114) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 7/8 (1140) 47 7/8 (1216) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) 34 5/16 (872) 35 13/16 (910) 32 3/4 (832) 32 (813) 38 5/16 (973) 39 13/16 (1011) 42 5/16 (1075) 43 13/16 (1113) 46 5/16 (1176) 47 13/16 (1214) 50 5/16 (1278) 51 13/16 (1316) 54 5/16 (1380) 55 13/16 (1418) 58 5/16 (1481) 59 13/16 (1519) 36 3/4 (933) 36 (914) 28 5/16 (719) 40 3/4 (1035) 40 (1016) 44 3/4 (1137) 44 (1118) 48 3/4 (1238) 48 (1219) 52 3/4 (1340) 52 (1321) 56 3/4 (1441) 56 (1422) 48 5/16 (1227) 44 5/16 (1126) 40 5/16 (1024) 36 5/16 (922) 32 5/16 (821) 24 5/16 (618) CDP2132 CDP2136 CDP2140 CDP2144 CDP2148 CDP2152 CDP2532 CDP2536 CDP2540 CDP2544 CDP2548 CDP2552 CDP2932 CDP3132 CDP3332 CDP3732 CDP4132 CDP2936 CDP3136 CDP3336 CDP3736 CDP4136 CDP2940 CDP3140 CDP3340 CDP3740 CDP4140 CDP2944 CDP3144 CDP3344 CDP3744 CDP4144 CDP2948 CDP3148 CDP3348 CDP3748 CDP4148 CDP2952 CDP3152 CDP3352 CDP3752 CDP4152 CDP2156 CDP2556 CDP2956 CDP3156 CDP3356 CDP3756 CDP4156 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-17

PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 24 7/8 (632) 27 7/8 (708) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) 28 7/8 (733) 31 7/8 (810) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 7/8 (835) 35 7/8 (911) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 7/8 (886) 37 7/8 (962) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 7/8 (937) 39 7/8 (1013) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 7/8 (1038) 43 7/8 (1114) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 7/8 (1140) 47 7/8 (1216) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) 60 3/4 (1543) 60 (1524) CDP2960 CDP3160 CDP3360 CDP3760 CDP4160 64 3/4 (1645) 64 (1626) CDP2964 CDP3164 CDP3364 CDP3764 CDP4164 68 3/4 (1746) 68 (1727) CDP2968 CDP3168 CDP3368 CDP3768 CDP4168 72 3/4 (1848) 72 (1829) CDP2972 CDP3172 CDP3372 CDP3772 CDP4172 78 5/16 (1989) 79 13/16 (2027) 76 3/4 (1949) 76 (1930) 68 5/16 (1735) 74 5/16 (1888) 75 13/16 (1926) 64 5/16 (1634) 70 5/16 (1786) 71 13/16 (1824) 60 5/16 (1532) 66 5/16 (1684) 69 13/16 (1773) 56 5/16 (1430) 62 5/16 (1583) 63 13/16 (1621) 52 5/16 (1329) CDP2160 CDP2560 CDP2164 CDP2564 CDP2168 CDP2568 CDP2172 CDP2572 CDP2176 CDP2576 CDP2976 CDP3176 CDP3376 CDP3776 CDP4176 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-18

PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 24 7/8 (632) 27 7/8 (708) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) 28 7/8 (733) 31 7/8 (810) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 7/8 (835) 35 7/8 (911) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 7/8 (886) 37 7/8 (962) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 7/8 (937) 39 7/8 (1013) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 7/8 (1038) 43 7/8 (1114) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 7/8 (1140) 47 7/8 (1216) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) 80 3/4 (2051) 80 (2032) CDP2980 CDP3180 CDP3380 CDP3780 CDP4180 88 3/4 (2254) 88 (2235) CDP2988 CDP3188 CDP3388 CDP3788 CDP4188 94 5/16 (2396) 95 13/16 (2434) 92 3/4 (2356) 92 (2337) 84 5/16 (2142) 90 5/16 (2294) 91 13/16 (2332) 80 5/16 (2040) 82 5/16 (2091) 83 13/16 (2129) 72 5/16 (1837) CDP2180 CDP2580 CDP2188 CDP2588 CDP2192 CDP2592 CDP2992 CDP3192 CDP3392 CDP3792 CDP4192 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-19

PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 7/8 (1241) 51 7/8 (1318) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) 52 7/8 (1343) 55 7/8 (1419) 50 1/8 (1273) 49 3/8 (1254) 42 13/16 (1087) 56 7/8 (1445) 59 7/8 (1581) 54 1/8 (1375) 53 3/8 (1356) 46 13/16 (1189) 64 7/8 (1648) 67 7/8 (1724) 62 1/8 (1578) 61 3/8 (1559) 54 13/16 (1392) 34 5/16 (872) 35 13/16 (910) 32 3/4 (832) 32 (813) 38 5/16 (973) 39 13/16 (1011) 42 5/16 (1075) 43 13/16 (1113) 46 5/16 (1176) 47 13/16 (1214) 50 5/16 (1278) 51 13/16 (1316) 54 5/16 (1380) 55 13/16 (1418) 58 5/16 (1481) 59 13/16 (1519) 36 3/4 (933) 36 (914) 28 5/16 (719) 40 3/4 (1035) 40 (1016) 44 3/4 (1137) 44 (1118) 48 3/4 (1238) 48 (1219) 52 3/4 (1340) 52 (1321) 56 3/4 (1441) 56 (1422) 48 5/16 (1227) 44 5/16 (1126) 40 5/16 (1024) 36 5/16 (922) 32 5/16 (821) 24 5/16 (618) CDP4532 CDP4536 CDP4540 CDP4544 CDP4548 CDP4552 CDP4932 CDP5332 CDP6132 CDP4936 CDP5336 CDP6136 CDP4940 CDP5340 CDP6140 CDP4944 CDP5344 CDP6144 CDP4948 CDP5348 CDP6148 CDP4952 CDP5352 CDP6152 CDP4556 CDP4956 CDP5356 CDP6156 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-20

PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 7/8 (1241) 51 7/8 (1318) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) 52 7/8 (1343) 55 7/8 (1419) 50 1/8 (1273) 49 3/8 (1254) 42 13/16 (1087) 56 7/8 (1445) 59 7/8 (1581) 54 1/8 (1375) 53 3/8 (1356) 46 13/16 (1189) 64 7/8 (1648) 67 7/8 (1724) 62 1/8 (1578) 61 3/8 (1559) 54 13/16 (1392) CDP4560 CDP4960 CDP5360 CDP6160 CDP4564 CDP4964 CDP5364 CDP6164 68 3/4 (1746) 68 (1727) 64 3/4 (1645) 64 (1626) 60 3/4 (1543) 60 (1524) CDP4568 CDP4968 CDP5368 CDP6168 72 3/4 (1848) 72 (1829) CDP4572 CDP4972 CDP5372 CDP6172 78 5/16 (1989) 79 13/16 (2027) 76 3/4 (1949) 76 (1930) 68 5/16 (1735) 74 5/16 (1888) 75 13/16 (1926) 64 5/16 (1634) 70 5/16 (1786) 71 13/16 (1824) 60 5/16 (1532) 66 5/16 (1684) 69 13/16 (1773) 56 5/16 (1430) 62 5/16 (1583) 63 13/16 (1621) 52 5/16 (1329) CDP4576 CDP4976 CDP5376 CDP6176 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-21

PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 7/8 (1241) 51 7/8 (1318) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) 52 7/8 (1343) 55 7/8 (1419) 50 1/8 (1273) 49 3/8 (1254) 42 13/16 (1087) 56 7/8 (1445) 59 7/8 (1581) 54 1/8 (1375) 53 3/8 (1356) 46 13/16 (1189) 64 7/8 (1648) 67 7/8 (1724) 62 1/8 (1578) 61 3/8 (1559) 54 13/16 (1392) 80 3/4 (2051) 80 (2032) CDP4580 CDP4980 CDP5380 CDP6180 88 3/4 (2254) 88 (2235) CDP4588 94 5/16 (2396) 95 13/16 (2434) 92 3/4 (2356) 92 (2337) 84 5/16 (2142) 90 5/16 (2294) 91 13/16 (2332) 80 5/16 (2040) 82 5/16 (2091) 83 13/16 (2129) 72 5/16 (1837) CDP4592 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-22

PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 72 7/8 (1851) 75 7/8 (1927) 70 1/8 (1781) 69 3/8 (1762) 62 13/16 (1595) 80 7/8 (2054) 83 7/8 (2130) 78 1/8 (1984) 77 3/8 (1965) 70 13/16 (1799) 34 5/16 (872) 35 13/16 (910) 32 3/4 (832) 32 (813) 38 5/16 (973) 39 13/16 (1011) 42 5/16 (1075) 43 13/16 (1113) 46 5/16 (1176) 47 13/16 (1214) 50 5/16 (1278) 51 13/16 (1316) 54 5/16 (1380) 55 13/16 (1418) 58 5/16 (1481) 59 13/16 (1519) 36 3/4 (933) 36 (914) 28 5/16 (719) 40 3/4 (1035) 40 (1016) 44 3/4 (1137) 44 (1118) 48 3/4 (1238) 48 (1219) 52 3/4 (1340) 52 (1321) 56 3/4 (1441) 56 (1422) 48 5/16 (1227) 44 5/16 (1126) 40 5/16 (1024) 36 5/16 (922) 32 5/16 (821) 24 5/16 (618) CDP6932 CDP6936 CDP6940 CDP6944 CDP6948 CDP6952 CDP7732 CDP7736 CDP7740 CDP7744 CDP7748 CDP7752 CDP6956 CDP7756 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-23

PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 72 7/8 (1851) 75 7/8 (1927) 70 1/8 (1781) 69 3/8 (1762) 62 13/16 (1595) 80 7/8 (2054) 83 7/8 (2130) 78 1/8 (1984) 77 3/8 (1965) 70 13/16 (1799) CDP6960 CDP7760 CDP6964 CDP7764 CDP6968 CDP7768 72 3/4 (1848) 72 (1829) 68 3/4 (1746) 68 (1727) 64 3/4 (1645) 64 (1626) 60 3/4 (1543) 60 (1524) CDP6972 CDP7772 78 5/16 (1989) 79 13/16 (2027) 76 3/4 (1949) 76 (1930) 68 5/16 (1735) 74 5/16 (1888) 75 13/16 (1926) 64 5/16 (1634) 70 5/16 (1786) 71 13/16 (1824) 60 5/16 (1532) 66 5/16 (1684) 69 13/16 (1773) 56 5/16 (1430) 62 5/16 (1583) 63 13/16 (1621) 52 5/16 (1329) CDP6976 CDP7776 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-24

PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 72 7/8 (1851) 75 7/8 (1927) 70 1/8 (1781) 69 3/8 (1762) 62 13/16 (1595) 80 7/8 (2054) 83 7/8 (2130) 78 1/8 (1984) 77 3/8 (1965) 70 13/16 (1799) 82 5/16 (2091) 83 13/16 (2129) 80 3/4 (2051) 80 (2032) 72 5/16 (1837) CDP6980 CDP7780 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-25

PICTUR UNITS WITH 16 FLANKRS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 99 5/8 (2530) 102 5/8 (2607) 96 7/8 (2461) 96 1/8 (2442) 14 13/16 (376)[2] 46 13/16 (1189) 107 5/8 (2734) 110 5/8 (2810) 104 7/8 (2664) 104 1/8 (2645) 14 13/16 (376)[2] 54 13/16 (1392) 54 5/16 (1380) 57 13/16 (1468) 52 3/4 (1340) 52 (1321) 21 1/16 (535)[2] 44 5/16 (1126) CD5352-16 CD6152-16 56 3/4 (1441) 56 (1422) CD5356-16 CD6156-16 66 5/16 (1684) 67 13/16 (1722) 64 3/4 (1645) 64 (1626) 27 1/16 (687)[2] 56 5/16 (1430) 58 5/16 (1481) 59 13/16 (1519) 23 1/16 (586)[2] 48 5/16 (1227) CD5364-16 CD6164-16 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/8 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-26

PICTUR UNITS WITH 20 FLANKRS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 107 5/8 (2734) 110 5/8 (2810) 104 7/8 (2664) 104 1/8 (2645) 18 13/16 (478)[2] 54 13/16 (1392) 115 5/8 (2937) 118 5/8 (3013) 112 7/8 (2867) 112 1/8 (2848) 18 13/16 (478)[2] 62 13/16 (1595) CD6152-20 CD6952-20 56 3/4 (1441) 56 (1422) 54 5/16 (1380) 57 13/16 (1468) 52 3/4 (1340) 52 (1321) 21 1/16 (535)[2] 44 5/16 (1126) CD6156-20 CD6956-20 66 5/16 (1684) 67 13/16 (1722) 64 3/4 (1645) 64 (1626) 27 1/16 (687)[2] 56 5/16 (1430) 58 5/16 (1481) 59 13/16 (1519) 23 1/16 (586)[2] 48 5/16 (1227) CD6164-20 CD6964-20 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/8 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-27

GNRAL INFORMATION SCTOR TOP SINGL-HUNG UNITS DIMNSIONAL WINDOWS Clad sector top single-hung windows may be specified as dimensional by adjusting the desired rough opening width or height in 1/4 increments from standard. Clad sector top single-hung windows feature stationary (fixed) upper sash and an operating lower sash. Counterbalancing is achieved with block and tackle spring extension systems hidden in weatherable PVC jambliners. Operating units are supplied with cam-type sash locks installed. Die-cast lower sash lifts supplied for field installation are an option. Recessed sash retainers provide simple sash installation and removal. There are several hardware finish options. Refer to the Specifications for available finish options. SITLIN X CLAD SCTOR TOP SINGL-HUNG WINDOWS utilize some of the same options as SITLIN X CLAD DOUBL-HUNG WINDOWS. Those options have not been repeated here in this sub-section. See the SITLIN X CLAD DOUBL-HUNG section for: Jamb xtender Options. October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-28

HANDING & OPRATION SCTOR TOP SINGL-HUNG UNITS SINGL-HUNG OPRATION: When the sash are locked at the check rails the sash are closed and sealed in the sash opening of the frame. When the sash are unlocked the lower sash travels vertically to any position desired. The upper sash is fixed. SASH TILTING FOR WASHING The Clad Single-Hung window will allow the lower sash to be tilted or removed for easy cleaning. October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-29

LVATION NOTS SCTOR TOP SINGL-HUNG UNITS LVATION DRAWINGS UTILIZ A LIMITD NUMBR OF PROJCTD LINS TO PRODUC A RUDIMNTARY DRAWING INTNDD TO B USD IN A SMALL GRAPHICAL SCAL. LVATIONS AR VIWD PRPNDICULAR FROM TH XTRIOR OF TH STRUCTUR. IF MOR DIMNSIONS AR NDD, US TH SCTION DRAWINGS FOR MOR COMPLT DPICTIONS. M.O. Brickmould M.O. Adams/Flat Casing Rough Opening Frame Size Daylight Opening 28 7/8 (733) 31 7/8 (810) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) Masonry Openings for Brickmould, Flat & Adams Casing. Vertical measurements include sillnose. (Subtract from Masonry Opening for Unit Size) 58 5/16 (1481) 59 13/16 (1519) 56 3/4 (1441) 56 (1422) 23 1/16 (586) 23 5/16 (592) DAYLIGHT OPNING OUTSID OF FRAM CDS INDICATS SITLIN X CLAD SCTOR TOP SINGL-HUNG TH FIRST TWO NUMBRS INDICAT TH UNIT WIDTH CDS2556 BOOK COD TH LAST TWO NUMBRS INDICAT TH UNIT HIGHT GNRAL SINGL-HUNG NOTS LVATION SYMBOL LGND: 1. ALL UNITS SHOWN AR AVAILABL AS OPRATORS ONLY. 2. UNIT LVATIONS AR SHOWN WITHOUT XTRIOR TRIM. 3. ALL OPRATING SASH AR INSTALLD WITH VINYL JAMB LINRS AND OPRATD WITH AN INTRNAL BLOCK AND TACKL SPRING SYSTM. 4. DIMNSIONAL VALUS IN PARNTHSS AR MILLIMTR CONVRSIONS. 5. VALUS IN BRACKTS AR NUMBR OF DAYLIGHT OPNINGS. MO MASONRY OPNING October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-30

SCTOR TOP UNITS - 1-WID M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 28 7/8 (733) 31 7/8 (810) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 7/8 (835) 35 7/8 (911) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 7/8 (886) 37 7/8 (962) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 7/8 (937) 39 7/8 (1013) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 7/8 (1038) 43 7/8 (1114) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 7/8 (1140) 47 7/8 (1216) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) CDS2556 CDS2956 CDS3156 CDS3356 CDS3756 CDS4156 CDS2560 CDS2960 CDS3160 CDS3360 CDS3760 CDS4160 64 3/4 (1645) 64 (1626) 60 3/4 (1543) 60 (1524) 56 3/4 (1441) 56 (1422) CDS2564 CDS2964 CDS3164 CDS3364 CDS3764 CDS4164 68 3/4 (1746) 68 (1727) CDS2568 CDS2968 CDS3168 CDS3368 CDS3768 CDS4168 74 5/16 (1888) 75 13/16 (1926) 72 3/4 (1848) 72 (1829) 31 1/16 (789) 31 5/16 (795) 70 5/16 (1786) 71 13/16 (1824) 29 1/16 (738) 29 5/16 (745) 66 5/16 (1684) 67 13/16 (1722) 27 1/16 (687) 27 5/16 (694) 62 5/16 (1583) 63 13/16 (1621) 25 1/16 (637) 25 5/16 (643) 58 5/16 (1481) 59 13/16 (1519) 23 1/16 (586) 23 5/16 (592) CDS2572 CDS2972 CDS3172 CDS3372 CDS3772 CDS4172 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-31

SCTOR TOP UNITS - 2-WID M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 54 1/4 (1378) 57 1/4 (1454) 51 (1308) 50 3/4 (1289) 18 13/16 (478)[2] 62 1/4 (1581) 65 1/4 (1657) 59 (1511) 58 3/4 (1492) 22 13/16 (579)[2] 70 1/4 (1784) 73 1/4 (1861) 67 (1715) 66 3/4 (1695) 26 13/16 (681)[2] 78 1/4 (1988) 81 1/4 (2064) 75 (1918) 74 3/4 (1899) 30 13/16 (783)[2] 58 5/16 (1481) 59 13/16 (1519) 56 3/4 (1441) 56 (1422) 23 1/16 (586) CDS2556-2 CDS2956-2 CDS3356-2 CDS3756-2 60 3/4 (1543) 60 (1524) CDS2560-2 CDS2960-2 CDS3360-2 CDS3760-2 64 3/4 (1645) 64 (1626) CDS2564-2 CDS2964-2 CDS3364-2 CDS3764-2 68 3/4 (1746) 68 (1727) CDS2568-2 CDS2968-2 CDS3368-2 CDS3768-2 74 5/16 (1888) 75 13/16 (1926) 72 3/4 (1848) 72 (1829) 31 1/16 (789) 31 5/16 (795) 70 5/16 (1786) 71 13/16 (1824) 29 1/16 (738) 29 5/16 (745) 66 5/16 (1684) 67 13/16 (1722) 27 1/16 (687) 27 5/16 (694) 62 5/16 (1583) 63 13/16 (1621) 25 1/16 (637) 25 5/16 (643) 23 5/16 (592) CDS2572-2 CDS2972-2 CDS3372-2 CDS3772-2 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-32

FULL RADIUS UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 32 7/8 (835) 35 7/8 (911) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 7/8 (886) 37 7/8 (962) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 7/8 (937) 39 7/8 (1013) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 7/8 (1038) 43 7/8 (1114) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 7/8 (1140) 47 7/8 (1216) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) 48 7/8 (1241) 51 7/8 (1318) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) CDH2956 CDH3156 CDH3356 CDH3756 CDH2960 CDH3160 CDH3360 CDH3760 CDH4160 CDH2964 CDH3164 CDH3364 CDH3764 CDH4164 CDH4564 CDH2968 CDH3168 CDH3368 CDH3768 CDH4168 CDH4568 74 5/16 (1888) 75 13/16 (1926) 72 3/4 (1848) 72 (1829) 31 1/16 (789) 31 5/16 (795) 70 5/16 (1786) 71 13/16 (1824) 68 3/4 (1746) 68 (1727) 29 1/16 (738) 29 5/16 (745) 66 5/16 (1684) 67 13/16 (1722) 64 3/4 (1645) 64 (1626) 27 1/16 (687) 27 5/16 (694) 62 5/16 (1583) 63 13/16 (1621) 60 3/4 (1543) 60 (1524) 25 1/16 (637) 25 5/16 (643) 58 5/16 (1481) 59 13/16 (1519) 56 3/4 (1441) 56 (1422) 23 1/16 (586) 23 5/16 (592) CDH2972 CDH3172 CDH3372 CDH3772 CDH4172 CDH4572 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 5-33