EPICVUE CLAD-WOOD PATIO DOOR SLIDING PATIO DOOR TABLE OF CONTENTS

Transcription

1 TABLE OF CONTENTS 1

2 Right Stationary GENERAL INFORMATION Dimensional Doors EpicVue Sliding Patio Doors may be specified as "dimensional", by adjusting the desired rough opening width or height in 1/16" increments from standard. EpicVue Sliding Patio Doors are available in single, twin, triple and quad panel doors. The standard size range includes sizes specifically designed for replacement of older patio door models in existing structures, as well as a full range of "true size" products for architectural consistency. Operation EpicVue Sliding Patio Doors are available in a full range of operating and stationary styles. Two-panel doors are available with left or right operation. Three-panel doors are available with left and right operation and with center or end operators. Configuration and handing is based on viewing the door from the exterior. Multiple Assemblies EpicVue Sliding Patio Doors are available in a wide variety of multiple panel configurations from the factory, all of which are assembled with continuous sills. Mulling of clad sliding patio doors to like products in the field is not recommended. Instead, individual factory assembled units should be installed in contiguous rough openings, in order to provide adequate framing support to assure the best performance of the door systems. 2

3 LITE CUT INFORMATION EpicVue Sliding Patio Doors are available with grilles in 5/8", 7/8", 1-1/8", 1-3/8", and 2-5/16" widths, with grilles between the glass (GBG), or with Simulated Divided Lites. Standard lite cuts are rectangular, and conform to the layouts noted in the charts on the next page. To use the chart, refer to the appropriate table by the type of patio door and type of bars or grilles the section drawings illustrate. Then simply cross reference the frame height and width to determine the standard lite cut. Lite Cut Options Special lite cut patterns can include a wide variety of straight line and radius patterns. The illustrations shown here represent just a few of the possibilities. Rectangular, horizontal, vertical and Prairie lite patterns are available in all standard size clad sliding patio doors. Uneven, diamond, radius and Gothic lite cuts are available, subject to approval. Approvals are based on the ability to fulfill the design requirement while maintaining the construction integrity of the finished product. Rectangular Horizontal Vertical Prairie Uneven Diamond Radius Gothic Bar Alignment Alignment of divided lite muntin bars from one product to the next is often required by fine architectural design. Wood grilles, GBG's, and Simulated Divided Lites may be specified with muntin bars aligned. 3

4 STANDARD LITE CUT TABLES Interior Exterior Contemp. Contemp. Putty Bead Putty Putty 5/8" 5/8" 5/8" 7/8" 7/8" 7/8" 1 1/8" 1 1/8" 1 1/8" 1 3/8" 1 3/8" 1 3/8" 2 5/16" 2 5/16" 2 5/16" NOTE: Each exterior SDL bar style can be paired with either Contemporary or Putty interior SDL bars. True Sizes CNGPDT 2-6 Width Callout Height Callout W 5H 2W 5H 2W 6H 2W 5H 2W 5H 2W 6H 3W 5H 3W 5H 3W 6H Height Callout CNGPDR Retro Sizes Width Callout W 5H 2W 5H 3W 5H 2W 5H 2W 5H 3W 5H 2W 6H 2W 6H 3W 6H 4

5 NARROW STILE CLEAR OPENING LAYOUT Clear Opening Height Vent Area Panel Callout Panel Width 3-0 True 37-17/ True 49-17/ True 61-17/32 Vertical Clear Opening = Frame Height - 4 3/16" Clear Opening Frame Width Operating Panel Stationary Panel Horizontal 2 Panel Unequal Sections Clear Opening = Operating Panel - 8 3/32" Operating Panel Frame Width Operating Panel Stationary Panel Horizontal 3-Panel Dual Operator Unequal Sections Clear Opening = (Frame Width - 3 3/4") - (2x Operating Panel Width + 4)/2 5

6 WIDE STILE CLEAR OPENING LAYOUT Clear Opening Height Vent Area Panel Callout 3-0 True 4-0 True 5-0 True Panel Width 38-15/ / /32 Vertical Clear Opening = Frame Height - 4 3/16" Clear Opening Frame Width Operating Panel Stationary Panel Horizontal 2 Panel Unequal Sections Clear Opening = Operating Panel /32" Clear Opening Panel Width Panel Width Horizontal 3-Panel End Operator Unequal Sections Clear Opening = (Frame Width - 3 3/4") - (2x Operating Panel Width + 4)/2 6

7 UNIT SIZING General Notes: Unit size is always the maximum size of the window with or without trim and does not include nail fin. Masonry Opening: Masonry opening is always 1/2" over (height and width) the unit size or the outside of the trim of the window. Rough Opening: Rough opening is always 3/4" over frame size of the window. A B C F E D 7

8 TRIM OPTIONS 2 1/2" 1 9/32" 1 9/32" 1 1/2" 2" 2 29/32" Kenison Casing 2" Flat Casing 3 1/2" Flat Casing 8

9 JAMB EXTENDER OPTIONS 4 5/8" Optional Intermediate Lock Rail 6 9/16" 2" 11/16" 2 3/4" Head Jamb Extender 4/4 (6 9/16 Jamb) 2 3/4" Standard 2 3/4" Bottom Rail 1 1/16" 2 5/16" 2" 5 7/8" Standard 2 3/4" Bottom Rail Standard Sill ( Jamb) 6 9/16" 4 5/8" Side Jamb Extender 5/4 (6 9/16 Jamb) Scale: 3" = 1' - 0" 9

10 MULLION OPTIONS 7 7/8" 3 1/2" 1 7/8" 1 5/16" 2 7/8" Scale: 6" = 1' - 0" 10

11 RAIL OPTIONS 2 3/4" 2 1/8" 1 7/16" 5 7/8" Narrow Bottom Rail 11" 4 5/8" 2 1/8" 1 7/16" 2 1/8" 1 7/16" 5 7/8" Standard Bottom Rail 5 7/8" 11" Bottom Rail 11

12 NARROW STILE 2 PANEL OPERATOR (OX) - VERTICAL SECTION 5 3/4" 1/2" 1 1/16" 2 3/4" Screen Size Daylight Opening Panel Size Frame Size Rough Opening 2 3/4" 2 1/16" 9/16" 5 7/8" Scale: 6" = 1' - 0" 12

13 NARROW STILE 2 PANEL OPERATOR (OX) - HORIZONTAL SECTION Rough Opening 3/8" Frame Size 3/8" 1 1/8" Panel Size Daylight Opening 2 3/4" 2 3/4" 1 3/4" 5 3/4" 5 3/4" 2 7/16" Panel Size 7/8" Screen Size 13

14 NARROW STILE 3 PANEL OPERATOR (XOX) - HORIZONTAL SECTION Rough Opening 3/8" Frame Size 1 1/8" Panel Size Daylight Opening 2 3/4" 2 3/4" 2 3/4" 5 3/4" 7/8" Screen Size 14

15 NARROW STILE 4 PANEL OPERATOR (OXXO) - HORIZONTAL SECTION Rough Opening 3/8" Frame Size Sash Size Daylight 2 3/4" 2 3/4" opening 5 3/4" Daylight 2 3/4" opening 2 3/4" 1 1/8" Sash Size Screen Size 15

16 WIDE STILE 2 PANEL OPERATOR (OX) - VERTICAL SECTION 5 3/4" 1/2" 1 1/16" 4 5/8" Screen Size Daylight Opening Panel Size Frame Size Rough Opening 4 5/8" 2 1/16" 9/16" 5 7/8" 16

17 WIDE STILE 2 PANEL OPERATOR (OX) - HORIZONTAL SECTION Rough Opening 3/8" 1 1/8" Panel Size Frame Size Daylight 4 5/8" 4 5/8" Opening 3/8" 1 3/4" 5 3/4" 5 3/4" 2 3/8" Panel Size 7/8" Screen Size Scale: 3" = 1' - 0" 17

18 WIDE STILE 3 PANEL OPERATOR (XOX) - HORIZONTAL SECTION Rough Opening 3/8" 1 1/8" Frame Size Panel Size 4 5/8" Daylight opening 4 5/8" 5 3/4" 7/8" Screen Size 2 3/8" 2 3/8" Scale: 3" = 1' - 0" 18

19 WIDE STILE 4 PANEL OPERATOR (OXXO) - HORIZONTAL SECTION Rough Opening 3/8" Frame Size Sash Size Daylight 4 5/8" 4 5/8" Opening 5 3/4" Daylight 4 5/8" Opening 4 5/8" 1 1/8" Sash Size Screen Size 19