WELD-MISER TEE-LET Welded Outlet Fittings

Similar documents
Welded Outlet Fittings For Fire Protection & Other Low Pressure Piping Systems

CAST IRON THREADED FITTINGS

UNIVERSAL FORGED STEEL ANVILETS

MODEL CB800 Circuit Balancing Valves

SECTION 1 Grooved Fittings

Class 300, Welding Neck, Slip-On and Threaded B16.47, Ser. A. ASME B16.5 Flanges

Pipe Fittings & Steel Nipples

Hole-cutting. cutting a hole. After the hole has been cut all rough edges must be removed and the area within 5/8 (16mm) of the hole

Model R. q Fig. 81-H: Standard Type: q A, q B, q C, q D, q E, q F. q Fig. C-81-H: Corrosion Resistant CONSTANT SUPPORTS.

Pipe Fittings & Steel Nipples

Section 2. Shurjoint Grooved Fittings Flow Data / Friction Resistance Ductile Iron Grooved Fittings. Wrought Grooved Fittings

GRUVLOK FITTINGS FOR GROOVED-END PIPE

Mechanical Piping.

Flexible Sprinkler Connections

Section 7. Socket Weld and Threaded Fittings. Socket Weld and Threaded Fittings 7-1

Forged Steel Fittings CLASS 3000 THREADED

Check Valves (C Series) Catalog 4130-C Revised, July 2004

STAINLESS STEEL FITTINGS

Introduction Parker are designed for uni-directional flow control of fluids and gases in industries such as chemical processing, oil and gas productio

Return not FoR ReSale Next Page

Quick Couplings. Section F

Copper-Nickel Alloy for Seawater Piping Systems (CuNi 90/10)

The Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York Bulletin 617 Rev. C

Forged steel socket Welding fittings 6 ~ 13. Forged steel threaded fittings 14 ~ 20. Forged steel outlet fittings 21 ~ 23

Ball Valves. ASME Class 150 to mm mm (¼" - 8") ISO 17292/ API 6D

030/TL 03/01 50M, Copyright 2001, Anvil International $3. 50

Yl)HAl STrrl (INDIA) Forged High Pressure Pipe Fittings. All ISO 9001:2003/ ISO 14001:2004 / 8S Ol!SAS 18001:2007 / PED Al'PROl'ED 97/23/EC

Order from MARYLAND METRICS P.O. Box 261 Owings Mills, MD USA web:

Gaugeable Tube Fittings and Adapter Fittings

Zurn Wilkins Fire Protection Series. Backflow Preventers, Pressure Regulating Valves, and Water Control Products for Fire Sprinkler Applications

Forged High Pressure Pipe Fittings

Table Of Contents. Assembly Instructions. Identification of Sync-Lok Tube Fittings. Reducing Port Connector 36. Male Elbow 11

08.12 Vic-Plug Balancing Valve

FTV-S (Straight) & FTV-A (Angle Body) Tri-Service Valve

FIG Gruvlok Flanges

Forged Fittings. High Technology Valve & Fitting Series

Steel Pipe Nipples & Malleable Fittings

Model RM-1 Riser Manifold Commercial and Residential General Description

Rosemount 1195 Integral Orifice Primary Element

Fittings, Materials and Tubing Guide. Instrumentation Products

HP Heat Exchanger Unit Heater

FLANGE. Flanges used for

B U I L D I N G C O N N E C T I O N S T H AT L A S T

Copper-Nickel Seawater Piping Systems Offshore product range: Pipes, fittings and flanges of OSNA 10

MANUFACTURING SPECIFICATION

Medium Duty Hydraulic Cylinders Series 3L

FIG Gruvlok Flange Adapter

Sanders, Buffers & Polishers Introduction

Grooved End Fittings. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE - GROOVED FITTINGS

Swagelok Medium-Pressure, Gaugeable Tube Fit tings and Adapte r Fit tings

Grooved End Fittings. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE - GROOVED FITTINGS

SimplAir Piping System. 3/4'' 8'' ( mm) Aluminum Pipe

SimplAir Piping System. 3/4'' 8'' ( mm) Aluminum Pipe

Thermo Scientific Gilmont

PIPE NIPPLES. Welded Pipe Nipples - Black & Galvanized. q Approved q Approved as noted q Not approved. Standard Schedule 40, XH Schedule 80

TECHNICAL DATA. Notes: For use with Trim Charts on Pages 2-4

A-C Fire Pump. Fitting and Accessories A-C 100A

ANVIL MANAGEMENT TEAM NORTH EAST REGION SOUTH EAST REGION IONAL, INC.

Bore (B) Pitch Diam. Drilling Template Flanges (1) Diam of Diam of. Groove. Neck D X G A Raised Face Raised Face P Raised face

VCR. Metal Gasket Face Seal Fittings. 1/16 to 1 in. and 6 to 18 mm sizes. High-purity stainless steels

Single, Two & Three-piece Ball Valves. ASME Class 150, 300 & mm mm (¼"- 8")

LIGHTWEIGHT + COMPACT. Rotary Union Solutions SPS. Series NPT CONNECTION SIZE OPTIONS

08.08 Vic-Check Valves

High Pressure Equipment High Pressure Valves, Fittings and Tubing

Figure 1: HB Series Ball Valve Cross Sectional View DISASSEMBLY WARNING: MAKE CERTAIN THE SYSTEM IN WHICH THE VALVE IS INSTALLLED IS EXHAUSTED OF ALL

Couplings - Quick Disconnect

Utilities Catalog. PC-U2008, February, 2008

High Pressure Valves, Fittings and Tubing Pressures to 65,000 psi

pneumatic swing clamps

UNITED BRAND FITTINGS

Series AIR LINE COMPRESSED AIR DISTRIBUTION SYSTEM

Integrated Process Solutions. Series 88. CF Component Ultra high vacuum fittings Sizes 1 1/3'' to 4 5/8''

Ford Fabricated Steel Products

28-1 & 29 Series. Compact, Light Weight Non-Spill Couplings. Compact Couplings for Applications Requiring Minimal Air Inclusion or Spillage

KUNKLE MODELS 19/19M/20/20M/20P/20MP/200A/200H LIQUID RELIEF VALVES SAFETY AND RELIEF PRODUCTS

connection solutions in stainless steel

contents MALLEABLE PIPE FITTINGS BUsHEs NiPPlEs PlUgs caps BENds BackNUTs UNioNs TEEs 171 cross PN25 p socket PN25 p socket PN25 p.

GBV-G Balancing Valves

2009 Edition. Tyton fittings 14"-24" NSF. For Water & Wastewater, Fire Protection & Industrial Applications. Certified to ANSI/NSF 61

Section 4 Flanges. Edition 3

COOPLOK Grooved Submittal. Material Specifications

Installation Instructions Capacity 10,000 lbs. DP10 (200 Series Lift)

MT SERIES PNEUMATIC ROTARY ACTUATORS

Pipe Flanges and Flanged Fittings

CUP ACCESSORIES SECTION 4 FLOW VALVES, CHECK VALVES, MECHANICAL VALVES, SWIVEL JOINTS, & TEE ADAPTORS EDCO USA.

Vic -300 Butterfly Valves

Section 3. Stainless Steel Series. Shurjoint Stainless Steel Piping Series Grooved Mechanical Couplings. Cast Grooved Fittings.

Instrument Pipe & ISO Conversion Fittings. Catalog 4260 Revised, February 1999

AIR NOZZLES AND JETS NEX FLOW AIR EDGER FLAT JET AIR NOZZLE

03/02/16 TECH DATA SHEET Pipe Nipples

TPCA Power Clamps Catalog

Worldwide leader in mechanical pipe joining solutions

Minimal Fitting Series

Vic -300 Butterfly Valves

Lubrication Installation Components, Accessories & Fittings Table of Contents

Medium Pressure Valves, Fittings and Tubing Pressures to 21,000 psi

Introduction. Marine Turbine Series. Model Illustrations. Special Notes. Specifications 77/1000MA 73/1000MA 75/500MAX 75/900MAX 79/1000MAV 75/1000MAX

High Pressure Valves, Fittings and Tubing Pressures to 65,000 psi

Risers/Saddles. NEW - 2 Poly Risers. All handline risers built at B. A. Fischer in Boise, ID. Black Poly Coated Orange.

You get it All. Quality products are not enough. Standardized carton sizes. Large. The benchmark of packaging

Transcription:

WL-ISR T-LT Welded ittings or ire Protection & Other Low Pressure Piping Systems erit Weld-iser Tee-Let Welding ranch ittings offer the user a high strength, low cost, welded steel, threaded and grooved line of fittings. Tee-Lets are specifically designed and manufactured to be installed on Schedules 5 thru 40 and proprietary thin wall flow pipe. or Listings/pproval etails and Limitations, visit our website at www.anvilintl.com or contact an nvil Sales Representative. erit Tee-Lets are steel welding outlet fittings. The material used in manufacture meets the chemical and physical requirements of ST 53, Grades or, Type. Tee-Lets employ a low weld volume design to provide for either a partial or full penetration weld employing a single pass with minimum burn-through and pipe distortion. Threads are NPT per S.20. or ISO 7/ Taper as ordered. Tee-Lets are UL Listed and pproved for use conforming to the requirements of NP 3. When used in fire sprinkler systems, Tee-Lets are rated for 300 psi or 75 psi on 6" Z-low Pipe. T-LT WL OUTLT ITTING (UL VIZU X3788 pproval Guide hapter Pipe ittings) odel Pipe Size Header Pipe Size** Rated Pressure In. In. psig Tee-Let Type (-Threaded nd) 2, 3 4,, 4, 2, 2, 2 2, 3, 4 4-8 300 Tee-Let Type (Grooved nd) 4-8 4-8 300 Tee-Let Type /R (Roll Grooved nd) 4-6 4-8 300 ** ontact your local nvil Representative for a complete list of UL approved propreitary flow pipe and sizes. Project: ddress: ontractor: ngineer: Submittal ate: Notes : Notes 2: PROJT INORTION PPROVL STP q pproved q pproved as noted q Not approved Remarks:

WL-ISR T-LT Welded ittings UNII SIGN SRIS erit's Unified esign Series carries all important design considerations into its entire line of welding branch outlet fittings. erit Weld-iser Tee-Lets are designed and anufactured to reduce the amount of weld required to install the Tee-Lets on thin wall or proprietary flow pipe. Typically only one weld-pass completes the installation. erit Tee-Lets install with less weld volume than any other brand of welding outlet fittings for fire sprinkler applications. To accomplish this: The contoured end of the fittings employs a reduced outside diameter. Two major advantages are immediately apparent: The thinner wall on the contoured end permits welding temperatures to be matched to the thickness of the branch line or main thereby insuring complete penetration without cold welds, weld roll-off, burnthrough or excessive distortion. On smaller sizes a heavier section is maintained on the threaded end of the fitting. This protects the threads from damage during shipping and handling prior to installation as well as from weld distortion. ach outlet size 2" and larger, whether male or female threaded, cut grooved or beveled requires the same hole size in the header pipe. This simplifies the installation process. Threads are cut in accordance with S.20. for NPT tapered pipe threads. ISO 7/ taper threads are available upon request. Tee-Let threaded and grooved welding outlet fittings are UL/UL Listed and pproved for use in the fire sprinkler systems installed in accordance with the requirements of NP 3. Tee-Lets are offered in a wide variety of header sizes. The consolidated header sizes shown in the following charts allow the fittings to be installed on more than one header size, permitting the first size listed to fit the header perfectly, while a small gap along the longitudinal center line of the header will appear for the second size listed. erit Weld-iser Tee-Lets are identified by a lot number that provides full traceability per ISO 9000 specifications. OR YOUR PIPING SYSTS SPIY WL-ISR T-LT ranch ittings shall be erit Weld-iser Tee-Let, Lightweight steel, employing low weld volume profile to provide for full penetration welds with minimum burn through and distortion on Schedules 5 thru 40 and proprietary thin wall pipe. Threads may be NPT per S.20. or ISO 7/ taper, and the bore of the fittings calculated to improve flow. Welding outlets to be UL Listed, pproved for use conforming to NP 3 and pressure rated for 300 PSI maximum. GNRL SPIITIONS Tee-Let welding outlet fittings are manufactured from highly weldable steel which conforms to the chemical and physical requirements of ST -53, Grades or, Type. ase of installation is assured when automatic welding equipment is used to install erit Tee-Lets.

WL-ISR T-LT Welded ittings Type emale Thread WL-ISR T-LT - Type Header Length Inside iameter ake Up Weight ach In./mm In./mm In./mm In./mm In./mm Lbs./kg 4 x 4-8 0.080 6 x 6-200 0.04 4-2.063 0.700 0.500 0.7 32-50 27.0 7.8 2.7 0.08 2 x 2-2 2.063 0.700 0.500 0.7 3 x 50-65 27.0 7.8 2.7 0.08 2 2-8.063 0.700 0.500 0.69 65-200 27.0 7.8 2.7 0.08 3 4 x 9 x x 25 x 4 x 32 x 2 x 40 x 4-2.25 0.900 0.500 0.260 32-50 28.6 22.9 2.7 0.2 2-2 2.25 0.900 0.500 0.260 50-65 28.6 22.9 2.7 0.2 2 2-8.25 0.900 0.500 0.256 65-200 28.6 22.9 2.7 0.2 4-2.250.45 0.500 0.33 32-40 3.8 29. 2.7 0.5 2-2.250.45 0.500 0.33 40-50 3.8 29. 2.7 0.5 2-2 2.250.45 0.500 0.320 50-65 3.8 29. 2.7 0.5 2 2-4.250.45 0.500 0.309 65-00 3.8 29. 2.7 0.4 5-8.250.45 0.500 0.29 25-200 3.8 29. 2.7 0.3 2-2.375.490 0.500 0.42 40-50 34.9 37.8 2.7.09 2-2 2.375.490 0.500 0.42 50-65 34.9 37.8 2.7.09 2 2-3.375.490 0.500 0.4 65-80 34.9 37.8 2.7.09 3-4.375.490 0.500 0.389 80-00 34.9 37.8 2.7.08 5-8.375.490 0.500 0.389 25-200 34.9 37.8 2.7.08 2.625.60 0.875 0.477 40 4.3 40.9 22.2.022 2.625.60 0.875 0.477 50 4.3 40.9 22.2.022 2 2.625.60 0.875 0.477 65 4.3 40.9 22.2.022 3-4.625.60 0.875 0.477 80-00 4.3 40.9 22.2.022 4.625.60 0.875 0.477 00 4.3 40.9 22.2.022 5-8.625.60 0.875 0.477 25-200 4.3 40.9 22.2.022 WL-ISR T-LT - Type Header Length Inside iameter ake Up Weight ach In./mm In./mm In./mm In./mm In./mm Lbs./kg 2.750 2.067 0.875 0.857 50 44.5 52.5 22.2 0.38 2 2.750 2.067 0.875 0.829 65 44.5 52.5 22.2 0.38 3.750 2.067 0.875 0.829 80 44.5 52.5 22.2 0.39 2 x 4.750 2.067 0.875 0.800 50 x 00 44.5 52.5 22.2 0.36 5.750 2.067 0.875 0.743 25 44.5 52.5 22.2 0.34 6.750 2.067 0.875 0.743 50 44.5 52.5 22.2 0.34 8.750 2.067 0.875 0.743 200 44.5 52.5 22.2 0.34 2 2 x 65 x 3 x 80 x 4 x 00 x 2 2 2.25 2.469.25.250 65 54.0 62.7 28.6 0.55 3 2.25 2.469.25.200 80 54.0 62.7 28.6 0.55 4 2.25 2.469.25.50 00 54.0 62.7 28.6 0.52 5 2.25 2.469.25.50 25 54.0 62.7 28.6 0.52 6 2.25 2.469.25.50 50 54.0 62.7 28.6 0.52 8 2.25 2.469.25.50 200 54.0 62.7 28.6 0.52 3 2.500 3.068.500.750 80 63.5 77.9 38. 0.79 4 2.500 3.068.500.700 00 63.5 77.9 38. 0.77 5 2.500 3.068.500.700 25 63.5 77.9 38. 0.77 6 2.500 3.068.500.650 50 63.5 77.9 38. 0.75 8 2.500 3.068.500.650 200 63.5 77.9 38. 0.75 4 3.000 4.026 2.000 3.000 00 76.2 02.3 50.8.36 5 3.000 4.026 2.000 2.900 25 76.2 02.3 50.8.32 6 3.000 4.026 2.000 2.800 50 76.2 02.3 50.8.27 8 3.000 4.026 2.000 2.800 200 76.2 02.3 50.8.27

WL-ISR T-LT Welded ittings Type ut Groove Standard Weight WL-ISR T-LT - Type ( Sizes " thru 2") Header Length Inside iameter Outside iameter Wall Thickness In./mm In./mm In./mm In./mm In./mm In./mm 4-2 3.049.35 0.33 32-40 80 26.6 33.4 3.4 2-2 3.049.35 0.33 40-50 80 26.6 33.4 3.4 x 2-2 2 3.049.35 0.33 25 x 50-65 80 26.6 33.4 3.4 2 2-4 3.049.35 0.33 65-00 80 26.6 33.4 3.4 5-8 3.049.35 0.33 25-200 80 26.6 33.4 3.4 4 x 32 x 2 x 40 x 2 x 50 x 4 3.368.660 0.40 32 80 34.7 42.2 3.6 2 3.368.660 0.40 40 80 34.7 42.2 3.6 2-2 2 3.368.660 0.40 50-65 80 34.7 42.2 3.6 3-4 3.368.660 0.40 80-00 80 34.7 42.2 3.6 5-8 3.368.660 0.40 25-200 80 34.7 42.2 3.6 2 3.60.900 0.45 40 80 40.9 48.3 3.7 2 3.60.900 0.45 50 80 40.9 48.3 3.7 2 2 3.60.900 0.45 65 80 40.9 48.3 3.7 3-4 3.60.900 0.45 80-00 80 40.9 48.3 3.7 5-8 3.60.900 0.45 25-200 80 40.9 48.3 3.7 2 3 2.067 2.375 0.54 50 80 52.5 60.3 3.9 2 2 3 2.067 2.375 0.54 65 80 52.5 60.3 3.9 3 3 2.067 2.375 0.54 80 80 52.5 60.3 3.9 4 3 2.067 2.375 0.54 00 80 52.5 60.3 3.9 5 3 2.067 2.375 0.54 25 80 52.5 60.3 3.9 6 3 2.067 2.375 0.54 50 80 52.5 60.3 3.9 8 3 2.067 2.375 0.54 200 80 52.5 60.3 3.9 Note: Tee-Lets are manufactured to fit size-on-size, that is the contoured shape on a given Tee-Let is made to fit perfectly on the first listed header size. If installed on the second header size marked on the fitting, a slight gap of approximately 32" will appear along the longitudinal centerline of the header. or example, a " x 2-2 2" Tee-Let, is a " outlet fitting manufactured to fit perfectly on the 2" header size listed, while leaving a 32" gap along the longitudinal centerline of the 2 2" size. If a perfect fit is required for a 2 2" header pipe, then a " x 2 2-3" Tee-Let would be ordered. Size consolidations are employed to reduce inventory and provide for greater flexibility.

WL-ISR T-LT Welded ittings Type ut Groove Standard Weight Type /R Roll Groove Schedule 0 WL-ISR T-LT - Type and /R ( Sizes 2 /2" thru 8") Header Length Inside iameter - Outside iameter Wall Thickness - Standard Weight Schedule 0 Standard Weight Schedule 0 In./mm In./mm In./mm In./mm In./mm In./mm In./mm In./mm 2 2 3 2.469 2.635 2.875 0.203 0.20 65 80 62.7 67.0 76.2 5.0 3.0 3 3 2.469 2.635 2.875 0.203 0.20 80 80 62.7 67.0 76.2 5.0 3.0 4 3 2.469 2.635 2.875 0.203 0.20 2 2 x 00 80 62.7 67.0 76.2 5.0 3.0 65 x 5 3 2.469 2.635 2.875 0.203 0.20 25 80 62.7 67.0 76.2 5.0 3.0 6 3 2.469 2.635 2.875 0.203 0.20 75 80 62.7 67.0 76.2 5.0 3.0 8 3 2.469 2.635 2.875 0.203 0.20 200 80 62.7 67.0 76.2 5.0 3.0 3 x 80 x 4 x 00 x 6 x 50 x 8 x 200 x 3 3 3.068 3.260 3.500 0.26 0.20 80 80 78.0 83.0 88.0 5.0 3.0 3 2 3 3.068 3.260 3.500 0.26 0.20 85 80 78.0 83.0 88.0 5.0 3.0 4 3 3.068 3.260 3.500 0.26 0.20 00 80 78.0 83.0 88.0 5.0 3.0 5 3 3.068 3.260 3.500 0.26 0.20 25 80 78.0 83.0 88.0 5.0 3.0 6 3 3.068 3.260 3.500 0.26 0.20 50 80 78.0 83.0 88.0 5.0 3.0 8 3 3.068 3.260 3.500 0.26 0.20 200 80 78.0 83.0 88.0 5.0 3.0 4 4 4.026 4.260 4.500 0.237 0.20 00 00 02.0 08.0 4.0 6.0 3.0 5 4 4.026 4.260 4.500 0.237 0.20 25 00 02.0 08.0 4.0 6.0 3.0 6 4 4.026 4.260 4.500 0.237 0.20 50 00 02.0 08.0 4.0 6.0 3.0 8 4 4.026 4.260 4.500 0.237 0.20 200 00 02.0 08.0 4.0 6.0 3.0 6 4 6.065 6.357 6.625 0.280 0.34 50 00 55.0 6.5 68.3 7. 3.0 8 4 6.065 6.357 6.625 0.280 0.34 200 00 55.0 6.5 68.3 7. 3.0 8 4 7.98 8.329 8.625 0.322 0.48 200 00 203.0 22.0 23.0 8.0 3.0 Note: Tee-Lets are manufactured to fit size-on-size, that is the contoured shape on a given Tee-Let is made to fit perfectly on the first listed header size. If installed on the second header size marked on the fitting, a slight gap of approximately 32" will appear along the longitudinal centerline of the header. or example, a " x 2-2 2" Tee-Let, is a " outlet fitting manufactured to fit perfectly on the 2" header size listed, while leaving a 32" gap along the longitudinal centerline of the 2 2" size. If a perfect fit is required for a 2 2" header pipe, then a " x 2 2-3" Tee-Let would be ordered. Size consolidations are employed to reduce inventory and provide for greater flexibility.

2024 © autodocbox.com Privacy Policy | Terms of Service | Feedback