SPOOL VALVE HYDRAULIC OTORS CONTENTS Page Hydraulic otors Series... 4 Hydraulic otors Series P... 13 Hydraulic otors Series R... 32 Hydraulic otors Series R...T (tacho)... 43 Hydraulic otors Series SP... 44 Hydraulic otors Series SR... Hydraulic otors Series RNA... 9 Hydraulic otors Series RFL... 6 Hydraulic otors with Dual Shaft Series RB... 62 Hydraulic otors Series PL... 6 Hydraulic otors Series RL... 7 Hydraulic otors Series PK... 7 Hydraulic otors Series RK... 79 Hydraulic otors Series RW... 83 Hydraulic otors Series H... 93 Hydraulic otors Series HW... 12 otor Special Features... 119 otors with Speed Sesor... 12 Applicatio Calculatios... 122 +S HYDRAULIC ca accept o resposibility for possible errors i catalogues, brochures ad other prited material. +S HYDRAULIC reserves the right to alter its products without otice. This also applies to products already o order provided that such alteratios ca be made without subsequetial chages beig ecessary i specificatios already agreed.
SPOOL VALVE HYDRAULIC OTORS GENERAL INFORATION: Orbit motors covert hydraulic eergy (pressure, oil flow) ito mechaical eergy (torque, speed). Hydraulic orbit motors operate o the priciple of a iteral gear (rotor) rotatig withi a fixed exteral gear (stator). The iteral gear trasmits the torque geerated by the applicatio of pressure from hydraulic oil fed ito motor which is the delivered via the motor's output shaft. Orbit motors have high startig torque ad costat output torque at wide speed rage. DISTRIBUTOR VALVE, P, R, SP, SR, H, PL, RL, PK, RK, RW, HW series motors have spool valve: the distributor valve has bee itegrated with the output shaft. The carda shaft rotates distributor valve ad trasfers mechaical eergy from gerotor set to output shaft. The valve has hydrodyamic bearigs ad has ifiite life whe load ratigs are ot exceeded. GEARWHEEL SET There are two forms of gearwheel set: - Gerotor set has plai teeth. These type of motors are suitable for log operatig periods at moderate pressures or short operatig periods at high pressures., P, SP, PL ad PK series motors have gerotor set. - Roll-gerotor set has teeth fitted with rollers. The rollers reduce local stress ad the tagetial reactio forces o the rotor reducig frictio to a miimum. This gives log operatig life ad better efficiecy eve at cotiuous high pressures. Roll-gerotor sets are recommeded for operatio with thi oil ad for applicatios with cotiually reversig loads. R, SR, RL, RK, H, RW ad HW series motors have roll-gerotor set. FEATURES: Stadard otor The stadard motor moutig flage is located as close to the output shaft as possible. This type of moutig supports the motor close to the shaft load. This moutig flage is also compatible with may stadard gear boxes. Wheel otor W moutig flage makes the motors possible to fit a wheel hub or a wich drum so that the radial load acts closer to motor bearigs. This gives the best utilizatio of the bearig capacity ad is a very compact solutio. Needle Bearig PN ad RN have a output shaft supported i eedle bearig. These types motors are suitable for operatig coditios such us frequet start ad stops, vibratio o the shaft, high static ad dyamic radial loads i short operatig terms. Low Leakage LL Series hydraulic motors are desiged to operate at the whole stadard rage of workig coditios (pressure drop ad frequecy of rotatio), but with cosiderable decreased volumetric losses i the drai ports. This motors are suitable for hydraulic systems with series-coected motors with demads for low leakage. Low Speed LSV feature optimizes the motor for low-speed performace. otors with this valvig provide very Valve low speed while maitaiig high torque. They are desiged to ru cotiuously at low speed (up to -1-1 2 mi ) at ormal pressure drop ad reduced flow. Optimal ru is guarateed at frequecy of rotatio from 2 to mi. otors with this valvig have a icreased startig pressure ad are ot recommeded for usig at pressure drop less tha 4 bar. Free Ruig FR motors are with icreased clearace at all frictio parts, allowig the shaft to rotate more freely with less mechaical drag. The icreased clearace also improves lubricatio of the wear surfaces of gear set ad frictio parts.additioal advatages of FR versio are prologig of the life of the hydraulic motors at high speeds, as well as the possibility to use them i systems with wide variatio of the loadig. FR Series motors are desiged to operate with high -1 speed /over tha 3 mi / ad low pressure drop. Volumetric efficiecy may be reduced slightly. High Pressure Shaft Seal The high pressure shaft seals allow the motors to withstad high case pressures at high speeds without exteral drai lie. otors with Speed Sesor otors are available with itegrated iductive speed sesor. The output sigal is a stadardized voltage sigal that ca be used to cotrol the speed of a motor. The torque ad the radial load of the motor are ot affected by the istallatio of speed sesor. 3
HYDRAULIC OTORS CONTENTS Specificatio data... Fuctio diagrams... 6 8 Dimesios ad moutig... 9 1 Shaft extesios... 11 Permissible shaft loads... 11 Order code... 12 GENERAL APPLICATION»»»»»» Coveyors Textile machies iig machiery achie tools Vetilators Costructio plat equipmet ad access platforms etc. OPTIONS» odel - Spool valve, gerotor» With or without flage» Side ad rear ports» Series with pressure valve(s)» Shafts - straight ad splied» etric ad BSPP ports» Speed sesorig;» Other special features ax. Displacemet, ax. Speed, ax. Torque, ax. Output, ax. Pressure Drop, ax. Oil Flow, i. Speed, Pressure fluid Temperature rage, cm /rev [i /rev] [RP] danm [ lb-ikw [ HP] bar [ PSI] lpm [ GP] [RP] O C [ F] 2 Optimal Viscosity rage, mm /s [SUS] Filtratio O [3.] 244 : 4, [ 398] it.:,8 [13] 3,2 [ 4.3] : 1 [ 1] it.: 14 [23] 2 [6.6] 2 ieral based- HLP(DIN 124) or H(ISO 6743/4) -4 14 [-4 284] 2 7 [ 98 347] ISO code 2/16 (i. recommeded fluid filtratio of 2 micro s) A P Series with Itegrated Iteral Crossover Relief Valve B, p=1 or bar [14 or 72 PSI] B P Series with Itegrated Iteral Crossover Relief Valve A, p=1 or bar [14 or 72 PSI] A A B B P PSI 3 2 2 1 1 P bar 2 16 12 8 4 Pressure Losses 2 4 6 8 1 12 14 16 18 2 22 24 Q, lpm A D Series with Itegrated Iteral Crossover Relief Valves B, p=1 or bar [14 or 72 PSI] A 1 2 3 4 6 7 Q, GP B 4
OTORS SPECIFICATION DATA Type Displacemet, cm /rev [ i /rev] ax. Speed, [RP] ax. Torque danm [ lb-i] 8 8,2 [.] 19 24 1, 1 [ 9] 1, [13] 12. 12, [.77] 1 194 1, 6[14] 2,3 [2] 2 19,9 [1.22] 1 12 2, [22] 3, [31] 32 31, 6 [1.93] 63 8 4, [3],7 [] 4 39,8 [2.43] 63 4, [ 4] 7, [ 62] [3.8] 4 4, 6 [ 41] 8,8 [ 78] ax. Output 2,1 [187] 1,8 [2.4] 3,3 [293] 2,4 [3. 2],1 [43] 2,4 [3. 2] 6,4 [68] 2,4 [3. 2] 8,2 [72] 2,2 [ 3.] 1, [88] 1, 8 [2.4] kw [ HP] 2,6 [3. ] 3,2 [4.3] 3,2 [4.3] 3,2 [4.3] 3, 2 [ 4.3] 3,2 [ 4.3] ax. Pressure Drop 1[14] 1 [14] 1 [14] 1[14] 9 [131] 7 [12] bar [ PSI] 14 [23] 14 [23] 14 [23] 14 [23] 14 [ 23] 14 [ 23] 2 [29] 2 [29] 2 [29] 16 [232] 16 [232] 16 [232] ax. Oil Flow 16 [4.2] 2 [. 3] 2 [. 3] 2 [. 3] 2 [. 3] 2 [. 3] lpm [ GP] 2 [. 3] 2 [6.6] 2 [6.6] 2 [6.6] 2 [6.6] 2 [6.6] ax. Ilet Pressure 14 [23] 14 [23] 14 [23] 14 [23] 14 [23] 14 [23] bar [PSI] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] ax. Retur Pressure -1 RP 14 [23] 14 [23] 14 [23] 14 [23] 14 [23] 14 [23] without Drai Lie or 1-4 RP 1 [1] 1 [1] 1 [1] 1 [1] 1 [1] 1 [1] ax. Pressure 4-8 RP [72] [72] [72] [72] [72] [72] i Drai Lie, >8 RP 2 [29] 2 [29] 2 [29] - - - bar [PSI] -max. RP 14 [23] 14 [23] 14 [23] 14 [23] 14 [23] 14 [23] ax. Retur Pressure 14 [23] 14 [23] 14 [23] 14 [23] 14 [23] 14 [23] with Drai Lie 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] bar [PSI] ax. Startig Pressure with Uloaded Shaft, bar [PSI] 4 [6] 4 [6] 4 [6] 4 [6] 4 [6] 4 [6] i. Startig Torque At max. press. drop,7 [6] 1,2 [1] 2,1 [18] 3,4 [3] 3, 8 [ 33] 4,1 [36] danm [ lb-i] At max. press. drop 1, [9] 1,7 [1] 2,9 [2] 4,8 [42] 6,2 [ ] 7,9 [ 7] i. Speed***, [RP] 4 3 3 2 2 Weight, kg [ lb] 1,9 [4.2] 2, [4.41] 2,1 [4.63] 2,2 [4.8] 2,3 [.7] 2, [.1] For "F" flage: +,2 [.441] F(S) P 2, [4.41] 2,2 [4.8] 2,1 [4.63] 2,3 [.7] 2,2 [4.8] 2,4 [.29] 2,3 [.7] 2, [.1] 2,4 [.29] 2,6 [.73] 2,6 [.73] 2,8 [6.17] D 2,6 [.73] 2,7 [.9] 2,8 [6.17] 2,9 [6.39] 3, [6.61] 3,2 [7.] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes.
otore OTORS FUNCTION DIAGRAS 8 lb-i danm Q=1 l/mi.26 GP 2 l/mi.3 GP 4 l/mi 1.6 GP 8 l/mi 2.11 GP 12 l/mi 3.17 GP 16 l/mi 4.23 GP 2 l/mi.28 GP 12 1,4 3 kw p=14 bar 23 PSI 1 7 1,2 1,,8,6 it. N=,2 kw, kw 1 kw t =73% 1, kw 2, kw 2 kw 12 bar 174 PSI 1 bar 14 PSI 7 bar 12 PSI,4 6% 2,2 % bar 72 PSI it. 3 bar 44 PSI 2 7 1 12 1 17 2 22 2 RP 12, lb-i danm Q=1 l/mi.26 GP 3 l/mi.8 GP l/mi 1.3 GP 1 l/mi 2.6 GP 1 l/mi 3.96 GP 2 l/mi.28 GP 2 l/mi 6.6 GP 2 17 2,4 2,2 2, 2, kw 3 kw p=14 bar 23 PSI 1 12 1 1,8 1,6 1,4 1,2 it. 1 kw 2 kw 1, kw 12 bar 174 PSI 1 bar 14 PSI 7 1,,8, kw t =73% 7 bar 12 PSI 2,6,4,2 N=,2 kw 7% 6% % it. bar 72 PSI 3 bar 44 PSI 2 4 6 8 1 12 14 16 18 2 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. 6
OTORS FUNCTION DIAGRAS 2 lb-i danm Q=3 l/mi.79 GP l/mi 1.32 GP 1 l/mi 2.64 GP 1 l/mi 3.96 GP 2 l/mi.28 GP 2 l/mi.6 GP 3 2 2 3, 3, 2, 2, it. 1 kw 1, kw 2 kw 2, kw 3 kw p=14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 1 1 1, 1,, N=,2 kw, kw t =73% 7% 6% % 7 bar 12 PSI bar 72 PSI 3 bar 44 PSI it. 1 2 3 4 6 7 8 9 1 11 12 13 32 RP lb-i danm Q=3 l/mi.79 GP l/mi 1.32 GP 1 l/mi 2.64 GP 1 l/mi 3.96 GP 2 l/mi.28 GP 2 l/mi.6 GP 6,, 4 4 3 3 2, 4, 4, 3, 3, 1 kw 1, kw 2 kw 2, kw 3 kw p=14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 2 1 1 2, 2, 1, 1,,, kw N=,2 kw t =73% 7% 6% % 7 bar 12 PSI bar 72 PSI 3 bar 44 PSI it. 1 2 3 4 6 7 8 The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. 7 RP
OTORS FUNCTION DIAGRAS 4 lb-i 6 danm 7 Q=3 l/mi.79 GP l/mi 1.32 GP 1 l/mi 2.64 GP 1 l/mi 3.96 GP 2 l/mi.28 GP 2 l/mi.6 GP 4 3 6 4 3 it. % 6% 6% t =7 % 7% 3 kw 2, kw 2 kw 1, kw p=12 bar 174 PSI 1 bar 14 PSI 8 bar 12 PSI 2 2 N=,2 kw, kw 1 kw bar 72 PSI 1 1 3 bar 44 PSI it. 1 2 3 4 6 RP lb-i danm 6 Q=3 l/mi.79 GP l/mi 1.32 GP 1 l/mi 2.64 GP 1 l/mi 3.96 GP 2 l/mi.28 GP 2 l/mi.6 GP 4 3 4 it. t =7% 1 kw 1, kw 7% 2 kw p=9 bar 13 PSI 7 bar 12 PSI 2 3 2 N=,2 kw, kw 6% 6% % bar 72 PSI 1 1 3 bar 44 PSI 1 bar 22 PSI it. 1 2 3 4 The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. 8 RP
DIENSIONS AND OUNTING DATA, S, P, D Three Bolts out SH Shaft C Shaft CK Shaft Shaft Dim. See Page 11 F Oval out (2 Holes) max 36,7 [1.44] max 33,4 [1.3] Flage Dim. See Page 1 max L max L ø6±,2 [2.362±.78] Rear Ports L1 Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized - CW 4 [.17] Port A T Port B Port Dim. See Page 1 S Side Ports max L Port A Port B L1 P T (A,B) : 2xG3/8 or 2x18x1, - 12 mm [.47 i] depth : G1/8 or 1x1-1 mm [.39 i] depth P Side Ports D Side Ports 4 [.17] max L 4 [.17] max L Port A Port A Port B Port B P (A,B) L1 L1 P (A,B) Type 8 12, 2 32 4 Type P 8 P 12, P 2 P 32 P 4 P L, mm [i.] 14 [ 4.94] 16 [ 4.173] 19 [ 4.291] 114 [ 4.488] 117, [ 4.626] 121, [ 4.783] L, mm [i.] 11 [ 4.28] 117 [ 4.66] 12 [ 4.724] 12 [ 4.921] 128, [.39] 132, [.217] Type S 8 S 12, S 2 S 32 S 4 S Type D 8 D 12, D 2 D 32 D 4 D L, mm [i.] 1 [ 4.134] 17 [ 4.213] 11 [ 4.331] 11 [ 4.28] 118, [ 4.66] 122, [ 4.823] L, mm [i.] 134 [.276] 136 [.34] 139 [.472] 144 [.669] 147, [.87] 11, [.96] L, 1 mm [i.] 3, [.138], [.217] 8, [.33] 13, [.31] 17 [.669] 21 [.827] L, 1 mm [i.] 3, [.138], [.217] 8, [.33] 13, [.31] 17 [.669] 21 [.827] P (A,B) For F Flage +3, mm 2, [.98] 9 mm [i]
OUNTING Three Bolts out F Oval out (2 Holes) 4 o [.197] 2xø9±,2 [.34±.78] ø4 [1.77], [.217] C ø6±,2 [2.362±.78] -.23 ø31, -,6 [1,24 ] 97 [3.819] 8±,2 [3.149±.78] -, ø63 [2,48 ] -.2 ø4±,2 [1.772±.78] 73 [2.874] 2±,2 [.79±.78] PORTS Rear Ports S Side Ports T P (A,B) 1,2±,3 [.98±.118] Port A Port B 4 [.17] 3,4 +,2 [1.197 ] -,1 +.79 -.39 max L Port A T 1,±,1 [.413±.39],4±,1 [.213±.39] 1,2±,3 [.98±.118] 11,7±,3 [.461±.12] Port B P (A,B) max 64 [2.2] P Side Ports with Sigle Crossover Relief Valve D Side Ports with Dual Crossover Relief Valve max L max L 4 [.17] Port A 2, [.98] Port A 3,4 +,2 -,1 [1.197 ] +.79 -.39 T 69 [2.716] -,1 +.79 -.39 3,4 +,2 [1.197 ] T 69 [2.716] 21,2±,1 [.83±.9] Port B P (A,B) max 64 [2.2] 4,3±,3 [1.87±.118] Port B P (A,B) max 64 [2.2] Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized - CW C P T (A,B) mm [i] : 3x6-12 mm [.47 i] depth : 2xG3/8 or 2x18x1, - 12 mm [.47 i] depth : G1/8 or 1x1-1 mm [.39 i] depth 1
OTORS SHAFT EXTENSIONS C - ø16 straight, Parallel key xx16 DIN 688 ax. Torque 3,9 danm [34 lb-i] CK - ø14 straight, Parallel key xx16 DIN 688 ax. Torque 3 danm [26 lb-i] -,3 [.197 ] -.12 -,3 [.197 ] -.12 ø16 +,6 -, +.24 -.19 [.63 ] ø17 [.669] 18-,13 [.79 ] -.1 ø14 -,18 [. ] -.7 ø17 [.669] 16-,13 [.63 ] -.1 +,4 28 6 +,4 28 +,17 [1.12 ] mi 11 [.433] deep +,17 [1.12 ] mi 1 6 1 [.433] deep SH - ø16, Splied, B17x14 DIN 482 ax. Torque 4,4 danm [39 lb-i] +2 +.79 14 [.1 ] ø16, -,11 [.649 ] -.43 ø17 [.669] mm [i] 28 +,4 +,17 [1.12 ] mi 1 6 1 [.433] deep PERISSIBLE SHAFT LOAD Pa max Prad lbs 4 36 3 2 1 =8 dan [18 lbs] Prad dan 18 16 12 8 4 2 mm [.79 i] P rad=16 dan [36 lbs] 4 6 8 1 12 14 16 18 2 RP The permissible radial shaft load [Prad] is calculated from the distace [L] betwee the poit of load applicatio ad the moutig surface: 6 134 P rad = X, [dan] 61,+L [L i mm; L 8 mm] 6 11 P rad =, [lbs] X 2.42 + L [L i ich; L 3.1 i] The drawig shows the permissible radial load whe L=2 mm [.79 i]. If the calculated shaft load exceeds the permissible, a flexible couplig must be used. 11
OTORS ORDER CODE 1 2 3 4 6 7 8 9 1 Pos.1 omit P* D* Pos.2 omit F Pos.3 omit S - Adjustmet Optio - without valve - Side ports with sigle crossover relief valve - Side ports with dual crossover relief valve Pos.4 - Displacemet code 8 12. 2 32 4 - outig Flage - Three bolts mout - Oval mout, two holes - Port type (ot valid for P ad D versio) - Rear ports - Side ports - 8,2 cm /rev [. i /rev] - 12,9 cm /rev [.79 i /rev] - 2, cm /rev [1.22 i /rev] - 31,8 cm /rev [1.93 i /rev] - 4, cm /rev [2.44 i /rev] -, cm /rev [3. i /rev] Pos. C VC CK SH Pos. 6 omit - Shaft Extesios* - ø16 straight, Parallel key Axx16 DIN688 - ø16 straight, Parallel key Axx16 DIN688 with corrosio resistat bushig - ø14 straight, Parallel key xx16 DIN688 - ø16, splied, B17x14 DIN 482 - Ports - BSPP (ISO 228) - etric (ISO 262) Pos. 7 - Lie to cotrol** (see page 4) /L - B A (left ruig) /R - A B (right ruig) Pos. 8 - Valve Rated Pressure*** / /8 /1 /14 - p= bar [72 PSI] - p=8 bar [116 PSI] - p=1 bar [14 PSI] - p= 14 bar [23 PSI] Pos. 9 - Special Features (see page 119) Pos.1 omit - Desig Series - Factory specified NOTES: * The permissible output torque for shafts must ot be exceeded! ** For P optio useful oly. *** For Pad Doptio useful oly. P ad D are available with ew crossover relief valves with improved characteristics. The ew valves allow easier pressure settig i a wider rage: from bar [72 PSI] to 14 bar [23 PSI]. For more iformatio about P ad D - series 2 please cotact with "+S Hydraulic". The Valve pressure settig must be at flow rate of 2 lpm [.3 GP]. The hydraulic motors are magao - phosphatized as stadard. F - FLANGE (2 Holes) Order No for Flage:48443 14 2xø9±,2 [.34±.78], [.217] 97 [3.819] 8±,2 [3.149±.78] -, ø63 [2,48 ] -.2 F Flage is mouted to the motor with 3 screws - 6x14. Tighteig Torque: -6 Nm [44-3 lb-i]. 73 [2.874] 2±,2 [.79±.78] 12
HYDRAULIC OTORS P APPLICATION»»»» Coveyors Feedig mechaism of robots ad maipulators etal workig machies Textile machies» Agricultural machies» Food idustries» Grass cuttig machiery etc. CONTENTS Specificatio data...14 17 Fuctio diagrams...18 24 Dimesios ad moutig... 2 26 Wheel motor... 27 Shaft extesios... 28 Permissible shaft loads... 29 Permissible shaft Seal Pressure... 3 Order code... 31 OPTIONS» odel - Spool valve, gerotor» Flage ad wheel mout» otor with eedle bearig» Side ad rear ports» Shafts - straight, splied ad tapered» Shaft seal for high ad low pressure» etric ad BSPP ports» Speed sesorig» Other special features GENERAL ax. Displacemet, ax. Speed, ax. Torque, ax. Output, ax. Pressure Drop, ax. Oil Flow, i. Speed, Pressure fluid Temperature rage, cm /rev [i /rev] [RP] danm [lb-i] kw [HP] bar [PSI] lpm [GP] [RP] O C [ F] 2 Optimal Viscosity rage, mm /s [SUS] Filtratio O 623,6 [ 38.] 181 : [ 441] it.: 64 [6] 12,8 [17.1] :14 [ 23] it.:[17 [24] 7 [ 19.8] 1 ieral based- HLP(DIN 124) or H(ISO 6743/4) -4 14 [-4 284] 2 7 [ 98 347] ISO code 2/16 (i. recommeded fluid filtratio of 2 micros) Pressure drop bar [ PSI] 1 [14] 14 [ 23] Oil flow i drai lie Viscosity Oil flow i drai lie 2 mm /s [ SUS] lpm [ GP] 2 [ 98] 3 [ 164] 2 [98] 3 [164] 2, [.66] 1,8 [.476] 3, [.92] 2,8 [.74] p bar 3 2 2 1 1 p PSI 4 3 2 1 Pressure Losses 2 4 6 8 1 12 14 16 18 2 Q, GP 1 2 3 4 6 7 8 Q, lpm 13
P OTORS SPECIFICATION DATA Specificatio Data for P... motors with C, CO, SH, Kad SA shafts. (ø28,6 sealig diameter) Type P 2 P 32 P 4 P P 8 P 1 P 12 Displacemet, cm³/rev [ i³/rev] 28,4 [ 1. 73] 34, [ 2,1] 4, [ 2.47] 49, [ 3.2] 79,2 [ 4.83] 99 [ 6.4] 123,8 [ 7.] ax. Speed, 148 14 148 121 7 6 486 [RP] 184 194 1 11 94 7 6 ax. Torque 3,3 [ 29] 4,3 [ 38] 6,2 [ ] 9,4 [ 83] 1,1 [ 134] 19,3 [ 171] 23,7 [ 21] danm [ lb-i] 4,7 [ 41] 6,1 [ 4] 8,2 [ 73] 11,9 [ 1] 19, [ 172] 23,7 [ 21] 29,8 [ 264] 6,7 [ 9] 8,6 [ 76] 1,7 [ 9] 14,3 [ 128] 22,4 [ 198] 27, [ 243] 36, [ 323] ax. Output 4, [ 6.],8 [ 7.8] 8,4 [ 11.] 1,1 [ 13.] 1,2 [ 13.7] 1, [ 14.1] 1,2 [ 13.7] kw [ HP] 6,1 [ 8.2] 7,8 [ 1.] 11,6 [ 1.] 12,2 [ 16.1] 12, [ 16.8] 12,8 [ 17.1] 12 [ 16.1] ax. Pressure Drop 1 [ 14] 1 [14] 12 [ 17] 14 [ 23] 14 [23] 14 [23] 14 [23] bar [ PSI] 14 [ 23] 14 [23] 1 [ 22] 17 [ 24] 17 [24] 17 [24] 17 [24] 22 [ 326] 22 [ 326] 22 [ 326] ax. Oil Flow 4 [ 1.] [ 13.2] 6 [ 1.9] 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] lpm [ GP] 4 [ 11.9] [ 14.] 7 [ 18.] 7 [ 19.8] ax. Ilet Pressure 17 [ 24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] bar [ PSI] 2 [ 29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 22 [ 326] ax. Retur Pressure 17 [ 24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] with Drai Lie 2 [ 29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] bar [ PSI] 22 [ 326] ax. Startig Pressure with Uloaded Shaft, bar [ PSI] 1 [14] 1 [14] 1 [14] 1 [14] 1 [14] 1 [14] 9 [ 131] i. Startig Torque At max.press. drop 3, [ 26] 4, [ 3],4 [ 48] 7,8 [ 69] 13,2 [ 117] 16,6 [ 147] 2,7 [ 183] danm [ lb-i] At max.press. drop 4,2 [ 37],6 [ ] 6,8 [ 6] 1 [ 88] 16,8 [ 149] 21 [ 186] 26,6 [ 236] i. Speed***, [RP] 2 1 1 1 1 1 1 Weight, kg [ lb] For rear ports +,4 [.992] P(F)(N) PW(N) PQ(N),6 [ 12.3],3 [ 11.7], [ 11.1],6 [12.3],3 [11.7], [11.1],7 [ 12.6],4 [ 11.9],1 [ 11.2],8 [ 12.8], [ 12.1],2 [ 11.],9 [ 13.2],6 [ 12.4],3 [ 11.7] 6,1 [ 13.],8 [ 12.8], [ 12.1] 6,2 [ 13. 7],9 [ 13],6 [ 12.3] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 14
P OTORS SPECIFICATION DATA (cotiued) Specificatio Data for P... motors with C, CO, SH, K ad SA shafts. (ø28,6 sealig diameter) Type Displacemet, cm³/rev [ i³/rev] ax. Speed, [RP] ax. Torque danm [ lb-i] ax. Output kw [ HP] ax. Pressure Drop bar [ PSI] ax. Oil Flow lpm [ GP] ax. Ilet Pressure bar [ PSI] ax. Retur Pressure with Drai Lie bar [ PSI] ax. Startig Pressure with Uloaded Shaft, bar [ PSI] i. Startig Torque danm [ lb-i] i. Speed***, [RP] Weight, kg [ lb] For rear ports +,4 [.992] At max.press. drop At max.press. drop P(F)(N) PW(N) PQ(N) P 16 18,4 [ 9.66] 378 472 31,3 [ 277] 37,8 [ 334] 43,8 [ 388] 1,1 [ 13.] 12,1 [ 16.2] 14 [23] 17 [24] 6 [1.9] 17 [24] 2 [29] 17 [24] 2 [29] 8 [ 116] 28,2 [ 2] 3, [ 314] 1 6,4 [ 14.1] 6,1 [ 13.],8 [ 12.8] P 2 33 378 36,6 [ 324] [ 487] 1 [ 13.] 12 [ 16.1] 14 [23] 17 [24] 6 [1.9] 17 [24] 2 [29] 17 [24] 2 [29] 7 [ 1] 1 6,6 [ 14.6] 6,3 [ 13.9] 6 [ 13.2] P 2 242 33 38 [ 336] 7, [ 1] 12 [ 16.1] 11 [ 16] 17 [24] 6 [1.9] 17 [24] 2 [29] 17 [24] 2 [29] 6 [ 87] 1 6,8 [ 1] 6, [ 14.3] 6,2 [ 13.7] P 31 19 236 38 [ 336] 4,6 [ 43] 8,3 [ 16] 6 [ 496] 68, [ 66] 8 [ 7],8 [ 7.9] 9 [ 12.1] 9 [ 13] 14 [ 23] 6 [1.9] 17 [24] 2 [29] 17 [24] 2 [29] [ 73] 1 7,1 [ 1.6] 6,8 [ 1] 6, [ 14.3] P 4 1 189 36 [ 319] 9 [ 24] 4,6 [ 6.2] 7,8 [ 1.] 7 [ 11] 11 [ 166] 6 [1.9] 17 [24] 2 [29] [73] 1 7,6 [ 16.8] 7,2 [ 1.9] 6,8 [ 1] P 198 [ 12.1] 247, [ 1.1] 316,8 [ 19.3] 396 [ 24.16] 49 [ 3.2] 623,6 [ 38.] 12 1 39 [ 342] 7 [ 4] 8,4 [ 76] 78 [ 693] 3, [ 4.7] 7,2 [.] 9 7 6 [ 87] 9 [ 13] 6 [1.9] 14 [23] 17 [24] [73] 33, [ 29] 33,6 [ 297] 34,4 [ 34] 34, [ 3] 36 [ 318] 42,6 [ 377] 4,2 [ 479] 61,9 [ 48] 6,8 [ 39] 4 [ 478] 1 8,9 [ 2] 8,6 [ 19] 8,3 [ 18.3] P 63 44 [ 389] 64 [ 66] 82 [ 727] 3,3 [ 4.4],6 [ 7.] [ 8] 8 [ 116] 18 [ 261] 13 [ 188] 11 [ 174] 17 [24] 14 [ 23] 14 [23] 2 [29] 17 [ 24] 17 [24] 22 [ 326] 14 [23] 17 [24] ] 9 12 6 [1.9] [73] 41, [ 367] 62 [ 48] 1 9, [ 21.4] 9,2 [ 2.3] 9 [ 19.8] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 1
P OTORS SPECIFICATION DATA (cotiued) Specificatio Data for P... motors with CB, KB, OB ad HB shafts. (ø3 sealig diameter) Type P 2 P 32 P 4 P P 8 P 1 P 12 Displacemet, cm³/rev [ i³/rev] 28,4 [1. 73] 34, [ 2,1] 4, [2.47] 49, [ 3.2] 79,2 [ 4.83] 99 [ 6.4] 123,8 [ 7.] ax. Speed, 148 14 148 121 7 6 486 [RP] 184 194 1 11 94 7 6 ax. Torque 3,3 [ 29] 4,3 [ 38] 6,2 [ ] 9,4 [ 83] 1,1 [ 134] 19,3 [ 171] 23,7 [ 21] danm [ lb-i] 4,7 [ 41] 6,1 [ 4] 8,2 [ 73] 11,9 [ 1] 19, [ 172] 23,7 [ 21] 29,8 [ 264] 6,7 [ 9] 8,6 [ 76] 1,7 [ 9] 14,3 [ 128] 22,4 [ 198] 27, [ 243] 36, [ 323] ax. Output 4, [ 6.],8 [ 7.8] 8,4 [ 11.] 1,1 [ 13.] 1,2 [ 13.7] 1, [ 14.1] 1,2 [ 13.7] kw [ HP] 6,1 [ 8.2] 7,8 [ 1.] 11,6 [ 1.] 12,2 [ 16.1] 12, [ 16.8] 12,8 [ 17.1] 12 [ 16.1] ax. Pressure Drop 1 [ 14] 1 [14] 12 [ 17] 14 [ 23] 14 [23] 14 [23] 14 [23] bar [ PSI] 14 [ 23] 14 [23] 1 [ 22] 17 [ 24] 17 [24] 17 [24] 17 [24] 22 [ 326] 22 [ 326] 22 [ 326] ax. Oil Flow 4 [ 1.] [ 13.2] 6 [ 1.9] 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] lpm [ GP] 4 [11.9] [ 14.] 7 [ 18.] 7 [ 19.8] ax. Ilet Pressure 17 [ 24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] bar [ PSI] 2 [ 29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 22 [ 326] ax. Retur Pressure 17 [ 24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] with Drai Lie 2 [ 29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] bar [ PSI] 22 [ 326] ax. Startig Pressure with Uloaded Shaft, bar [ PSI] 1 [14] 1 [14] 1 [14] 1 [14] 1 [14] 1 [14] 9 [ 131] i. Startig Torque At max.press. drop 3, [ 26] 4, [ 3],4 [ 48] 7,8 [ 69] 13,2 [ 117] 16,6 [ 147] 2,7 [ 183] danm [ lb-i] At max.press. drop 4,2 [ 37],6 [ ] 6,8 [ 6] 1 [ 88] 16,8 [ 149] 21 [ 186] 26,6 [ 236] i. Speed***, [RP] 2 1 1 1 1 1 1 Weight, kg [ lb] For rear ports +,4 [.992] P(F)...B,6 [ 12.3],6 [12.3],7 [ 12.6], 9 [ 13] 6 [ 13.2] 6, 2 [ 13. 7] 6, 3 [ 13.9] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 16
P OTORS SPECIFICATION DATA (cotiued) Specificatio Data for P... motors with CB, KB, OB ad HB shafts. (ø3 sealig diameter) Type Displacemet, cm³/rev [ i³/rev] ax. Speed, [RP] ax. Torque danm [ lb-i] ax. Output kw [ HP] ax. Pressure Drop bar [ PSI] ax. Oil Flow lpm [ GP] ax. Ilet Pressure bar [ PSI] ax. Retur Pressure with Drai Lie bar [ PSI] ax. Startig Pressure with Uloaded Shaft, bar [ PSI] i. Startig Torque danm [ lb-i] i. Speed***, [RP] Weight, kg [ lb] For rear ports +,4 [.992] At max.press. drop At max.press. drop P(F)...B P 16 18,4 [ 9.66] 378 472 31,3 [ 277] 37,8 [ 334] 43,8 [ 388] 1,1 [ 13.] 12,1 [ 16.2] 14 [23] 17 [24] 6 [1.9] 17 [24] 2 [29] 17 [24] 2 [29] 8 [ 116] 28,2 [ 2] 3, [ 314] 1 6, [ 14. 3] P 2 33 378 36,6 [ 324] P 2 242 33 47 [ 416] 9 [ 12.1] 12 [ 16.1] 17 [24] 6 [1.9] 6 [ 87] 1 6,9 [ 1.2] P 31 19 236 48 [ 436] 4,6 [ 43] 8,3 [ 16] 6 [ 496] 1 [ 13.] 12 [ 16.1] 7 [ 1] 1 6, 7 [ 14. 8] 7,6 [ 1.2] 9 [ 12.1] 14 [ 23] 11 [ 167] 6 [1.9] [ 73] 1 7,2 [ 1.9] P 4 1 189 [ 441] 9 [ 24] 6,2 [ 8.3] 7,8 [ 1.] 14 [23] 14 [23] 12 [ 174] 9 [ 14] 17 [24] 6 [1.9] 6 [1.9] [73] 1 7,7 [ 17] P P 63 198 [ 12.1] 247, [1.1] 316,8 [19.3] 396 [24.16] 49 [ 3.2] 623,6 [ 38.] 12 1 39 [ 342] 7 [ 4] [ 487] 68, [ 66] 8 [ 7] 8,4 [ 76] 78 [ 693] 3, [ 4.7] 7,2 [.] 9 7 6 [ 87] 9 [ 13] 6 [1.9] [73] 33, [ 29] 42,8 [ 379] 4 [4,8] 46,8 [ 414] 36 [ 318] 42,6 [ 377] 4,2 [ 479] 48 [61,9] 6,8 [ 39] 4 [ 478] 1 9, [19.9] 44 [ 389] 64 [ 66] 82 [ 727] 3,3 [ 4.4],6 [ 7.] [ 8] 8 [ 116] 22 [ 326] 18 [ 261] 13 [ 188] 11 [ 174] 17 [24] 17 [24] 17 [24] 17 [24] 14 [ 23] 14 [23] 2 [29] 2 [29] 2 [29] 2 [29] 17 [ 24] 17 [24] 22 [ 326] 17 [24] 17 [24] 17 [24] 17 [24] 14 [23] 14 [23] 2 [29] 2 [29] 2 [29] 2 [29] 17 [24] 17 [24] 9 12 6 [1.9] [73] 41, [ 367] 62 [ 48] 1 9, 6 [ 21. 2] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 17
P OTORS P 2 FUNCTION DIAGRAS lb-i 4 danm Q= l/mi 1.3 GP 1 l/mi 2.6 GP 1 l/mi 4. GP 2 l/mi.3 GP 2 l/mi 6.6 GP 3 l/mi 7.9 GP 3 l/mi 9.2 GP 4 l/mi 1.6 GP 4 l/mi 11.9 GP 4 3 3 2 2 1 1 4 3 2 1 it. 1 kw. kw N=.2 kw 2 kw t=73% 6% 2 4 6 8 1 12 14 16 18 RP 4 kw % 6 kw it. p=14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 3 bar 43 PSI P 32 lb-i 6 danm Q= l/mi 1.3 GP 1 l/mi 2.6 GP 1 l/mi 4. GP 2 l/mi.3 GP 2 l/mi 6.6 GP 3 l/mi 7.9 GP 3 l/mi 9.2 GP 4 l/mi 1.6 GP 4 l/mi 11.9 GP l/mi 13.2 GP l/mi 14. GP 6 p=14 bar 23 PSI 4 4 3 3 2 4 3 it. N=. kw 1 kw 2 kw 4 kw 6 kw 12 bar 174 PSI 1 bar 14 PSI 8 bar 116 PSI 2 1 2 t=78% 6 bar 87 PSI 1 1 7% 2 4 6 8 1 12 14 16 18 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. 6% % it. 3 bar 43 PSI 18
P OTORS P 4 FUNCTION DIAGRAS lb-i 7 7 6 6 4 4 3 3 2 2 1 1 danm 8 7 6 4 3 2 1 it. Q= l/mi 1.3 GP 1 l/mi 2.6 GP N=. kw 2 l/mi.3 GP 1 kw t=78% 3 l/mi 7.9 GP 2 kw 7% 7% 4 kw 6% 4 l/mi 1.6 GP 2 4 6 8 1 12 14 16 18 RP 6 kw % l/mi 13.2 GP 6 l/mi 1.9 GP 8 kw 1 kw 7 l/mi 18. GP it. p=1 bar 22 PSI 14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 3 bar 43 PSI P lb-i 11 danm 12 Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 1 9 8 7 6 4 3 2 11 1 9 8 7 6 4 3 2 it. N=1 kw 2 kw 4 kw t=7% 6 kw 7% 6% 12 kw 8 kw 1 kw % p=17 bar 24 PSI 16 bar 232 PSI 14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 1 1 2 4 6 8 1 12 14 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. it. 3 bar 43 PSI 19
P OTORS FUNCTION DIAGRAS P 8 lb-i 18 danm 2 Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 16 14 12 1 8 6 4 18 16 14 12 1 8 6 4 it. % 6% 7% 4 kw t=7% 2 kw N=1 kw 12 kw 1 kw 8 kw 6 kw p=17 bar 24 PSI 16 bar 232 PSI 14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 2 2 1 2 3 4 6 7 8 9 RP it. 3 bar 43 PSI P 1 lb-i 22 danm 24 Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 2 18 16 14 12 1 8 6 4 22 2 18 16 14 12 1 8 6 4 it. % 6% 7% 7% N=1 kw t=78% 2 kw 4 kw 6 kw 12 kw 1 kw 8 kw p=17 bar 24 PSI 16 bar 232 PSI 14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 2 2 1 2 3 4 6 7 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. it. 3 bar 43 PSI 2
P OTORS FUNCTION DIAGRAS P 12 lb-i danm Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 2 28 2 1 1 24 2 16 12 8 4 it. % 6% 7% N=1 kw 7% t=78% 2 kw 4 kw 6 kw 8 kw 1 kw p=17 bar 24 PSI 16 bar 232 PSI 14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI it. 3 bar 43 PSI 1 2 3 4 6 RP P 16 lb-i 36 danm Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 32 36 28 24 2 16 12 8 32 28 24 2 16 12 8 it. % 6% 7% 7% t=78% N=1 kw 2 kw 4 kw 6 kw 8 kw 1 kw 12 kw p=17 bar 24 PSI 16 bar 232 PSI 14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 4 4 it. 3 bar 43 PSI 1 1 2 2 4 4 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. 21
P OTORS FUNCTION DIAGRAS lb-i 4 danm Q= l/mi 1.3 GP P 2 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 4 4 3 3 2 2 1 1 4 3 3 2 2 1 1 it. % 6% 7% 7% t=77% N=1 kw 2 kw 4 kw 6 kw 8 kw 1 kw p=17 bar 24 PSI 16 bar 232 PSI 14 bar 23 PSI 11 bar 167 PSI 1 bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI it. 3 bar 43 PSI 1 1 2 2 RP P 2 lb-i 4 4 3 3 2 2 1 1 danm 6 4 4 3 3 2 2 1 1 Q= l/mi 1.3 GP it. 1 l/mi 2.6 GP 2 l/mi.3 GP % 3 l/mi 7.9 GP 6% N=1 kw t=8% 7% 7% 2 kw 4 l/mi 1.6 GP 4 kw 1 1 2 2 3 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. l/mi 13.2 GP 22 6 kw 6 l/mi 1.9 GP 8 kw 7 l/mi 18. GP 1 kw 7 l/mi 19.8 GP it. p=17 bar 24 PSI 16 bar 232 PSI 14 bar 23 PSI 12 bar 181 PSI 1 bar 14 PSI 8 bar 123 PSI 6 bar 87 PSI 3 bar 43 PSI
P OTORS FUNCTION DIAGRAS P 31 lb-i 6 danm 64 Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 4 4 3 3 2 2 1 1 6 48 4 32 24 16 8 it. % 6% 7% t=73% N=1 kw 6 kw 4 kw 8 kw 2 kw 2 7 1 12 1 17 2 22 2 RP it. p=16 bar 232 PSI 14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 8 bar 123 PSI 7 bar 12 PSI bar 73 PSI 3 bar 43 PSI P 4 lb-i 6 danm 6 6 Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 4 3 3 2 2 1 1 4 4 4 3 3 2 2 1 1 it. % 6% 7% N=1 kw 7% t=8% 2 kw 4 kw 6 kw p=12 bar 181 PSI 11 bar 16 PSI 9 bar 138 PSI 8 bar 116 PSI 6 bar 94 PSI bar 8 PSI 4 bar 6 PSI 3 bar 43 PSI 2 7 1 12 1 17 2 The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. it. RP 23
P OTORS P FUNCTION DIAGRAS lb-i 7 6 6 4 4 3 3 2 2 1 1 danm 7 7 6 6 4 4 3 3 2 2 1 1 Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP N=,kW 3 l/mi 7.9 GP 1kW 8% 4 l/mi 1.6 GP 2kW 3kW 7% l/mi 13.2 GP 4kW 7% 6 l/mi 1.9 GP kw 6kW 6% % 7 l/mi 18. GP 6% it. 7 l/mi 19.8 GP 1 2 3 4 6 7 8 9 1 11 12 13 14 1 p=11 bar 16 PSI 9 bar 13 PSI 7 bar 19 PSI 6 bar 87 PSI 4 bar 6 PSI 3 bar 43 PSI 1 bar 22 PSI RP P 63 lb-i 6 6 danm 7 6 6 Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 4 4 3 3 2 2 1 1 4 4 3 3 2 2 1 1 N=,kW 1kW 8% 2kW 7% 1 2 3 4 6 7 8 9 1 11 12 The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. 24 3kW 7% 6% 4kW 6% kw % it. p=8 bar 116 PSI 7 bar 12 PSI bar 8 PSI 4 bar 6 PSI 3 bar 43 PSI 1 bar 22 PSI RP
P OTORS SA Shaft SH Shaft K Shaft C Shaft CO Shaft DIENSIONS AND OUNTING DATA SA Shaft SH Shaft K Shaft C Shaft CO Shaft max [2.16] max [2.16] Shaft Dim. See Page 28 max 49 [1.929] max 49 [1.929] max L 38±,1 [1.496±.9] P (A,B) Port A C Port B 74±,3 [2.913±.118] Flage Dim. See Page 26 max L 44±,1 P (A,B) [1.732±.9] Port A 8±,3 [3.149±.118] Port B C L1 Port Dim. See Page 26 L1 T max ø91 [3.4] E Rear ports max ø91 [3.4] OB Shaft KB Shaft CB Shaft HB Shaft max L max 7 [2.76] max 68,3 [2.689] SB Shaft max 14 [.1] mm [i] C P T (A, B) : 4x8-13 mm [.1 i] depth : 2xG1/2 or 2x22x1, - 1 mm [.9 i] depth : G1/4 or 14x1, - 12 mm [.47 i] depth (plugged) Type P(F) 2 P(F) 32 P(F) 4 P(F) P(F) 8 P(F) 1 P(F) 12 P(F) 16 P(F) 2 P(F) 2 P(F) 31 P(F) 4 P(F) P(F) 63 2 Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized - CW L, mm [i] Type L, mm [i] Type L, mm [i] Type L, mm [i] L, 1 mm[i] 134, 13, 136, 13, 139, 142, 14, 1, 1, 162, 171, 182, 19, 213, [.28] [.31] [.37] [.33] [.49] [.9] [.73] [.91] [6.12] [6.38] [6.7] [7.17] [7.7] [8.39] PQ 2 PQ 32 PQ 4 PQ PQ 8 PQ 1 PQ 12 PQ 16 PQ 2 PQ 2 PQ 31 PQ 4 PQ PQ 63 14, 141, 142, 142, 146, 148, 12, 16, 162, 168, 178, 188, 22, 219, [.3] [.7] [.61] [.9] [.7] [.8] [.98] [6.16] [6.38] [6.63] [7.1] [7.42] [7.9] [8.62] P(F)E 2 P(F)E 32 P(F)E 4 P(F)E P(F)E 8 P(F)E 1 P(F)E 12 P(F)E 16 P(F)E 2 P(F)E 2 P(F)E 31 P(F)E 4 P(F)E P(F)E 63 1, [.91] 11, [.96] 12, [6.] 11, [.96] 1, [6.12] 18, [6.24] 161, [6.36] 166, [6.6] 171, [6.7] 178, [7.3] 187, [7.38] 198, [7.81] 211, [8.33] 229, [9.2] PQE 2 PQE 32 PQE 4 PQE PQE 8 PQE 1 PQE 12 PQE 16 PQE 2 PQE 2 PQE 31 PQE 4 PQE PQE 63 16, [6.16] 17, [6.2] 18, [6.24] 18, [6.22] 162, [6.38] 164, [6.48] 168, [6.61] 172, [6.79] 178, [7.1] 184, [7.26] 194, [7.64] 24, [8.] 218, [8.8] 23, [9.2],2 6,3 7,4 6,67 1,67 13,33 16,67 21,33 [.21] [.2] [.29] [.26] [.42] [.2] [.66] [.84] 26,67 [1.] 33,33 [1.31] 42,67 [1.68] 3,33 [2.1] 66,63 [2.62] 84, [3.31]
P OTORS OUNTING 2xø13,3 +,4 +.16 [.2 ] Oval out (2 Holes) 8±,3 [.31±.118] 13 [.118] ø16,4±,2 [4.189±.79] ø82,±, [3.248±.19] F - Oval out (4 Holes) ±,1 [2.16±.39] max 11 [3.976] 16 [.63] 4 4xø13,3 +,4 [.2 +.16] ø16,4±,2 [4.189±.79] 8±,3 [.31±.118] Q - Square out (4 Bolts) ±,1 [2.16±.39] ø82,±,1 [3.2±.39] mi 1 deep [.9] 82 [3.228] ø44,4±, [1.748±.19] 13 [.118] 4x1 ø82,±, [3.248±.19] ±,1 [2.16±.39] max 11 [3.976] 16 [.63] 82 [3.228] max 11 [3.976] 2,3±,3 [.98±.118] mm [i] Side Ports PORTS E Rear Ports 18±,1 [.78±.39] 2±,3 [.787±.118] C Port A 2±,3 [.787±.118] max 11 [3.976] ±,1 [2.16±.39] max L Port A 2 [.787] ±,1 [2.16±.39] [. 197] 2 [.984] Port B 18±,1 [.78±.39] Port B P (A,B) T P (A,B) T 13,9 [.47] 2±,3 [.787±.118] 2±,3 [.787±.118] 28,8 [1.134] C P T (A, B) : 4x8-13 mm [.1 i] depth : 2xG1/2 or 2x22x1, - 1 mm [.9 i] depth : G1/4 or 14x1, - 12 mm [.47 i] depth (plugged) 26 Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized - CW
P OTORS DIENSIONS AND OUNTING DATA - PW W - Wheel out max L mi 2 [.787] L1 4x1 ø79±,2 [3.11±.79] P (A,B) 2±,1 [.787±.39] 18,±,1 [.728±.39] ø8 -,46 [3.149-.18] Port A Port B 78±1 [3.71±.39] 7 +, [.27 +.196 ] 6,4±,1 [2.74±.9] 4±, [1.7±.196] 18,±,1 [.728±.39] max 112,4 [4.42 Type PW 2 PW 32 PW 4 PW PW 8 PW 1 PW 12 PW 16 PW 2 PW 2 PW 31 PW 4 PW PW 63 L, mm [i] 77, 78, 79, 78, 82, 8, 88, 93, 98, 1, 114, 12, 138, 16, [3.3] [3.7] [3.13] [3.9] [3.2] [3.3] [3.48] [3.66] [3.88] [4.13] [4.1] [4.92] [.4] [6.14] L, 1 mm[i],2 6,3 7,4 6,67 1,67 13,33 16,67 21,33 26,67 33,33 42,67 3,33 66,63 84, [.21] [.2] [.29] [.26] [.42] [.2] [.66] [.84] [1.] [1.31] [1.68] [2.1] [2.62] [3.31] max 1 [4.134] ±,1 [2.16±.39] ø86±,2 [3.386±.79] T mm [i] max 1 [3.937] Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized - CW P T (A, B) : 2xG1/2 or 2x22x1, - 1 mm [.9 i] depth : G1/4 or 14x1, - 12 mm [.47 i] depth (plugged) ø13±,1 [4.±.39] PERISSIBLE SHAFT LOADS PWN PW P rad dan 16 14 12 1 8 6 The curves apply to a B1 bearig life of 2 hours. P rad lbs 36 3 3 2 2 1 Pa max=1 dan [ 33 lbs] Pa max=2 dan + - [ 44 lbs] 1. ax. radial shaft load 2. = RP 3. =2 RP 4. =8 RP 1 2 3 4 P rad dan 16 14 12 1 8 6 P rad lbs 36 3 3 2 2 1 Pa max=1 dan [ 33 lbs] Pa max=2 dan + - [ 44 lbs] 1 1. ax. radial shaft load 2. =3 RP 3. = RP 4. =8 RP 2 3 4 4 1 4 1 2 2 4 3 2 1 i 4 3 2 1 i 12 1 8 6 4 2 mm 12 1 8 6 4 2 mm 27
P+R OTORS SHAFT EXTENSIONS FOR P AND R OTORS C - ø2 straight, Parallel key A8x7x32 DIN 688 ax. Torque 34 danm [31 lb-i] 8 -,36 [.31 ] -.14 CB - ø32 straight, Parallel key A1x8x4 DIN 688 ax. Torque 77 danm [681 lb-i] 1 -,36 [.394-.14] 28 -,3 [1.12 ] -.118 ø28,6 [1.124] ø2 +,1 +,2 +.7 +.1 [.984 ] 3 -,2 [1.378 ] -.79 ø3 [1.378] ø32 +,18 +,2 +.7 +.1 [1.26 ] 8 mi 18 [.71] deep 43,2±, [1.7±.197] 8 mi 18 [.71] deep +,4 6, -1, +.16 [2.224 -.39] CO - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 ax. Torque 34 danm [31 lb-i] SB - splied A2x22xH1 DIN 482 ax. Torque 34 danm [31 lb-i] 6,4 -, [.22 ] -.19 +,1 -,13 28,1 [1.16 ] +.39 -.1 ø28,6 [1.124] -,2 ø2,4 [1. ] -.8 ø22±, 13 [.866±.1] A-A ø2±,21 [.984±.83] ø3 [1.378] A ø26 +,2 +.79 [1.24 ] 6 8 mi 18 [.71] deep 43,2±, [1.7±.197] 18, [.728] 22±,4 [.866±.16] A SH - splied, BS 29 (SAE 6B) ax. Torque 4 danm [ 34 lb-i] KB - tapered 1:1, Parallel key B6x6x2 DIN 688 ax. Torque 77 danm [681 lb-i] +,2 6,2 -, +.1 [.246-.19] ø21,47±,7 [.84±.27] 8 mi 18 [.71] deep ø28,6 [1.124] mi 26,4 [1.39] 43,2±, [1.7±.197] ø2,32±,3 [.997±.12 A-A 6 -,3 [.236 ] -.11 19,1-,1 [.71 ] +.39 ø3±,1 [1.378±.88] 8±,4 [2.283 ±.16] 36±,7 [1.417±.27] 1:1 A A 4 [.17] 13 [.12] S=41 Tighteig torque 2±1 danm [177±88 lb-i] ø4, [.177] 2x1, [.196] ø44 [1.732] K - tapered 1:1, Parallel key Bxx14 DIN 688 ax. Torque 4 danm [34 lb-i] A-A -,3 [.197 ] -.11 24±,4 [.94 ±.16] 1:1 A 2, [.87] S=3 Tighteig torque 1±1 danm [88±88 lb-i] OB - tapered 1:8 SAEJ 1, Parallel key "x 16 16 "x1¼" BS46 ax. Torque 77 danm [681 lb-i] A-A 7,96 -,2 [.313 ] -.8 +,4 6, -1, +.16 [2.224 -.39] 3±,6 [1.377±.236] ø4 [.17] A S=1 7/16" Tighteig torque 2±1 danm [177±88 lb-i] max 1,4 [.66] ø28,6±,1 [1.124±.88] A 2x1, ø4, [.177] ø44 [1.732] 17 -,6 +,16 [.669 ] +.63 -.24 ø3 [1.378] A +,31 4-,29 +.122 [2.126 -.114 ] 1-2 UNEF [.196] SA - splied, B2x22h9 DIN 482 ax. Torque 4 danm [34 lb-i] HB - ø1¼" splied 14T, ANSI B92.1-1976 Norm ax. Torque 77 danm [681 lb-i] ø28,6 [1.124] ø24, ø3 [1.378] ø31,77-, -,13 [.964 ] [1.2 ] -.19 -.1 ø31,7-,2 [1.2 ] -.1 8 mi 18 [.71] deep mm [i] 26,4±1 [1.39±.39] 43,2±, [1.7±.197] 28 mi 1 8 8 [.71] deep 36 +2 [1.417 +.79] +,4 6, -1, +.16 [2.224 -.39]
P+R OTORS PERISSIBLE SHAFT LOADS FOR P AND R OTORS The permissible radial shaft load Prad depeds o the speed, RP, distace L from the poit of load to the moutig flage ad shaft versio. outig Flage Shaft Versio cylidrical - C, CO tapered - K, splied - SH 8 Radial Shaft Load P rad,i mm x 2, dan* 9+L Radial Shaft Load P rad,i ich * < _ 2 RP; max Prad=8 dan [18 lbs] >2 _ RP; L < mm [2.2 i] 8 221 x,lbs* RP 3.74+L P AND R splied - HB cylidrical - CB 8 x 187 9+L, dan* 8 166 x,lbs* RP 3.74+L cylidrical - C, CO 8 x 2, dan* 11+L 8 221 x,lbs* RP 3.98+L Radial Shaft Load Prad for C, CO Shaft Extesios by L=3 mm [1.18 i] (24 mm [.94 i]) P rad P rad dan 9 8 6 4 2 P rad lbs 2 16 12 8 4 P max= 1 dan [ 33 lbs] P max= 2 dan [ 44 lbs] L= 3 [ 1.18] Oval out 2 4 6 8 RP Square out L= 24 [.94] PN AND RN The curves apply to a B1 bearig life of 2 hours. P rad dan P rad lbs 16 14 12 1 8 6 4 2 3 3 2 2 1 1 Pa max=1 dan [ 33 lbs] Pa max=2 dan [ 44 lbs] + - 1 2 3 4 1. ax. radial shaft load 2. = RP 3. =2 RP 4. =8 RP 8 3 2 1-1 i 6 4 2-2 mm 29
P+R OTORS AX. PERISSIBLE SHAFT SEAL PRESSURE FOR P AND R OTORS P/R...U1 motors with high pressure seal ad without drai coectio: The shaft seal pressure equals the average of iput pressure ad retur pressure. P/R...U motors with high pressure seal ad drai coectio: The shaft seal pressure equals the pressure i the drai lie. P = P iput +P seal 2 retur P/R...1 motors with low pressure seal or stadard shaft seal ad without drai coectio: The shaft seal pressure ever exceeds the pressure i the retur lie. P/R... motors with low pressure seal or stadard shaft seal ad with drai coectio: The shaft seal pressure equals the pressure i the drai lie. P bar 2 1 1 P PSI 3 2 2 1 1 1 14 3 2 1 4 1 2 4 6 8 1, RP 1: Drawig for Low Pressure Seal 2: Drawig for Stadard Shaft Seal for "...B" shafts 3: Drawig for Stadard Shaft Seal ("D" Seal) 4: Drawig for High Pressure Seal ("U" Seal) - cotiuous operatios - itermittet operatios 3
P OTORS ORDER CODE P 1 2 3 4 6 7 8 9 1 Pos.1- outig Flage omit F Q W Pos.2 omit N Pos.3 - Port type omit E Pos.4 - Displacemet code 2* 32* 4* 8 1 12 16 2 2 31 4 63 - Oval mout, two holes - Oval mout, four holes - Square mout, four bolts - Wheel mout - Optio (eedle bearigs) - oe - with eedle bearigs - Side ports - Rear ports 3 3 -- 2, cm /rev[1.2 [ 1.2 i i /rev] /rev] 3 3 -- 32, cm /rev[1.9 [ 1.9 i i /rev] /rev] 3 3 -- 4, cm /rev[2.44 [ 2.44 i i /rev] /rev] 3-49, cm /rev [3.2 [ i i /rev] 3-79,2 cm /rev [4.83 [ i i /rev] 3-99, cm /rev [6.4 [ 6.4 i i /rev] /rev] 3-123,8 cm /rev [7. [ 7. i i /rev] /rev] 3-18,4 cm /rev [9.66 [ 9.66 i i /rev] /rev] - 198, cm /rev [12.1 i /rev] - 247, cm /rev [1.1 i /rev] - 316,8 cm /rev [19.3 i /rev] - 396, cm /rev [24.16 i /rev] - 49, cm /rev [3.2 i /rev] - 623,6 3 cm /rev [38. 3 i /rev] Pos. C VC CO VCO SH VSH K SA VSA CB KB SB OB HB Pos. 6 omit D U Pos. 7 - Drai Port omit - with drai port 1 - without drai port Pos. 8 - Ports omit Pos. 9 - Special Features (see page 119) Pos.1 omit - Shaft Extesios **(see page 28) - ø2 straight, Parallel key A8x7x32 DIN688 - ø2 straight, Parallel key A8x7x32 DIN688 with corrosio resistat bushig - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 with corrosio resistat bushig - ø2,32 splied BS 29 (SAE 6B) - ø2,32 splied BS 29 (SAE 6B) with corrosio resistat bushig - ø28,6 tapered 1:1, Parallel key Bxx14 DIN688 - ø24, splied B 2x22 DIN 482 - ø24, splied B 2x22 DIN 482 with corrosio resistat bushig - ø32 straight, Parallel key A1x8x4 DIN688 - ø3 tapered 1:1, Parallel key B6x6x2 DIN688 - splied A 2x22 DIN 482 - ø1¼" tapered1:8, Parallel key / "x / "x1¼" BS46 - ø1¼" splied 14T ANSI B92.1-1976 - Desig Series - Factory specified 16 16 - Shaft Seal Versio (see page 3) - Low pressure shaft seal or Stadard shaft seal for... B shaft - Stadard shaft seal - High pressure shaft seal (without check valves) - BSPP (ISO 228) - etric (ISO 262) NOTES: * Not with Low Pressure Seal ** The permissible output torque for shafts must ot be exceeded! The followig combiatios are ot allowed: - Q flage with...b shafts; - W flage with...b shafts or E rear ports; - N optio with...b shafts, Low Pressure Seal or U optio; -...B shafts with D ad U shaft seals. The hydraulic motors are magao-phosphatized as stadard. 31
HYDRAULIC OTORS R APPLICATION»»»» Coveyors Feedig mechaism of robots ad maipulators etal workig machies Textile machies» Agricultural machies» Food idustries» Grass cuttig machiery etc. CONTENTS Specificatio data...29 3 Fuctio diagrams...31 39 Dimesios ad moutig... 4 41 Shaft extesios... 28 Permissible shaft loads... 29 Permissible shaft Seal Pressure... 3 Order code... 42 GENERAL ax. Displacemet, ax. Speed, ax. Torque, ax. Output, ax. Pressure Drop, ax. Oil Flow, i. Speed, Pressure fluid Temperature rage, cm /rev [i /rev] [RP] danm [lb-i] kw [HP] bar [PSI] lpm [GP] [RP] O C [ F] 2 Optimal Viscosity rage, mm /s [SUS] Filtratio O OPTIONS» odel - Spool valve, roll-gerotor» Flage mout» otor with eedle bearig» Side ad rear ports» Shafts - straight, splied ad tapered» Shaft seal for high ad low pressure» etric ad BSPP ports» Speed sesorig» Other special features 397 [ 24.4] 97 : 61 [ 4] it.: 69 [61] 1 [ 2.1] : 17 [ 24] it.: 2 [29] 7 [2] 1 ieral based- HLP(DIN 124) or H(ISO 6743/4) -4 14 [- 4 284] 2 7 [ 98 347] ISO code 2/16 (i. recommeded fluid filtratio of 2 micros) Oil flow i drai lie Pressure Losses Pressure drop bar [ PSI] 1 [14] 14 [ 23] Viscosity Oil flow i drai lie 2 mm /s [ SUS] lpm [ GP] 2 [ 98] 3 [ 164] 2 [98] 3 [164] 2, [.66] 1,8 [.476] 3, [.92] 2,8 [.74] p bar 3 2 2 1 1 p PSI 4 3 2 1 2 4 6 8 1 12 14 16 18 2 Q, GP 1 2 3 4 6 7 8 Q, lpm 32
R OTORS SPECIFICATION DATA Specificatio Data for R... motors with C, CO, SH, Kad SA shafts. (ø28,6 sealig diameter) Type 3 Displacemet, cm /rev R 1, R 8 8,3 R 1 99,8 R 12 12,7 R 16 19,6 R 2 199,8 R 2 2,1 R 31 31,7 R 4 397 3 [ i /rev ] [3.14] [ 4.9] [ 6.9] [ 7.67] [ 9.74] [ 12.19] [ 1.26] [ 19.26] [ 24.4] ax. Speed, 77 7 6 47 37 3 24 19 1 [RP] 97 94 7 6 47 37 3 24 19 ax. Torque 1 [ 9] 2 [ 177] 24 [ 212] 3 [ 26] 39 [ 34] 38,[ 341] 39 [ 34] 36 [ 318] 38 [ 336] danm [ i-lb] 13 [ 11] 22 [ 1947] 28 [ 248] 34 [ 31] 43 [ 38] 46 [ 47] 47 [416] 47 [416] 47 [416] 17 [ 1] 27 [ 239] 32 [ 2832] 37 [ 327] 46 [ 47] 6 [ 496] 6 [31] 61 [4] 61 [4] ax. Output 7 [ 9.] 12, [ 17] 13 [ 17.4] 12,[ 16.8] 11,[ 1.4] 9 [ 12] 8 [1.7] [6.7] 4,8 [ 6.4] kw [ HP] 8, [ 11.9] 1 [ 2.1] 1 [ 2.1] 14,[ 19.] 14 [ 18.8] 12 [16.1] 9, [ 12.7] 8 [1.7] 6,8 [9.1] ax. Pressure Drop 14[ 23] 17[ 24] 17[ 24] 17[ 24] 17[ 24] 14[ 23] 11[ 16] 8 [123] 6 [94] bar [ PSI] 17[ 24] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 17[ 24] 14[23] 11[167] 9 [13] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 2[29] 1[217] 11[167] ax. Oil Flow 4 [ 1.] 6 [ 1.8] 6 [ 1.8] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] lpm [ GP] [ 13.2] 7 [19.8] ax. Ilet Pressure 17[ 24] 17[ 24] 17[ 24] 17[ 24] 17[ 24] 17[ 24] 17[ 24] 17[ 24] 17[ 24] bar [ PSI] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 22[ 326] ax. Retur Pres- 17[ 24] 17[ 24] 17[ 24] 17[ 24] 17[ 24] 17[ 24] 17[ 24] 17[ 24] 17[ 24] sure with Drai Lie 2[ 29] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 2[ 29] bar [ PSI] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 22[ 326] ax. Startig Pressure with Uloaded Shaft, bar [ PSI] 1 [ 14] 1 [ 14] 1 [ 14] 9 [ 13] 7 [ 12] [ 73] 4 [ 8] 3 [ 44] 3 [ 44] i. Startig Torque At max.press. danm [ i-lb] drop 8 [ 71] 1 [ 133] 2 [ 177] 2 [ 221] 32 [ 2832] 33 [ 292] 31 [ 274] 31,[287] 31,[ 287] At max.press. drop 1 [ 8] 17 [ 1] 23 [ 23] 28 [ 248] 37 [ 327] 4 [ 34] 48 [ 42] 8 [ 22] [ 442] i. Speed***, [RP] 1 1 1 1 1 1 1 1 1 Weight, kg [ lb] R(F) 6,8 [ 1] 6,9 [ 1,2] 7,2 [ 1.9] 7,3 [ 16.1] 7, [ 1.2] 8 [ 17.6] 8,4 [ 18.] 9,1 [ 2] 9,8 [ 21.6] For rear ports : +,6 [ 1.433] RQ(N) 6,2 [ 13.7] 6,3 [ 13.9] 6,6 [ 14.6] 6,8 [ 1] 7, 2 [4 1. 7] 7, 6 [. 1 4] 7,8 [ 17.2] 8,6 [ 19] 9,3 [ 2.] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 33
R OTORS SPECIFICATION DATA (cotiued) Specificatio Data for R... motors with CB, KB, OB ad HB shafts. (ø3 sealig diameter) Type 3 Displacemet, cm /rev 3 [i /rev ] ax. Speed, [RP] ax. Torque danm [ i-lb] ax. Output kw [ HP] ax. Pressure Drop bar [ PSI] ax. Oil Flow lpm [ GP] ax. Ilet Pressure bar [ PSI] ax. Retur Pressure with Drai Lie bar [ PSI] ax. Startig Pressure with Uloaded Shaft, bar [ PSI] i. Startig Torque danm [ i-lb] i. Speed***, [RP] Weight, kg [ lb] For rear ports : +,6 [ 1.433] At max.press. drop At max.press. drop R [ 3.14] 1 7 77 8, [ 11.9] R 8 R 1 R 12 R 16 14[ 23] 17[ 24] 17 [ 24] 17[ 24] 17[ 24] 17[ 24] 2[ 29] 2 [ 29] 2[ 29] 2[ 29] 22[ 326] 22[ 326] 22 [ 326] 22[ 326] 22[ 326] 4 [ 1.] [ 13.2] 17[ 24] 17[ 24] 17 [ 24] 17[ 24] 17[ 24] 2[ 29] 2[ 29] 2 [ 29] 2[ 29] 2[ 29] 22[ 326] 22[ 326] 22 [ 326] 22[ 326] 22[ 326] 17[ 24] 17[ 24] 17 [ 24] 17[ 24] 17[ 24] 2[ 29] 2[ 29] 2 [ 29] 2[ 29] 2[ 29] 22[ 326] 22[ 326] 22 [ 326] 22[ 326] 22[ 326] 1 8 1 1, 97 1 6,9 [ 1,2] [ 4.9] 1 8,3 7 94 1 [ 6.9] 6 7 6 [ 1.8] 6 [ 1.8] 13 [ 17.4] 12,[ 16.8] 11,[ 1.4] 1 99,8 1 12,7 [ 7.67] 9 47 6 1 [ 9.74] 37 47 [ 9] 2 [ 177] 24 [ 212] 3 [ 26] 39 [ 34] 13 [ 11] 22 [ 1947] 28 [ 248] 34 [ 31] 43 [ 38] 17 [ 1] 27 [ 239] 32 [ 2832] 37 [ 327] 46 [ 47] [ 9.] 12, [ 17] [ 14] 1 [ 2.1] 1 [ 2.1] 14,[ 19.] 14 [ 18.8] [ 14] [ 14] 6 [ 1.8] 6 [ 1.8] [ 71] 1 [ 133] 2 [ 177] 2 [ 221] 32 [ 2832] [ 88] 17 [ 1] 23 [ 23] 28 [ 248] 37 [ 327] 7 19,6 [ 13] [ 12] 1 7 [ 1,4] 7,3 [ 16.1] 7,4 [ 16.3] 7,6 [ 1.4] R 2 [ 12.19] 3 37 R 2 R 31 R 4 17[ 24] 17[ 24] 13[ 196] 11 [ 16] 2[ 29] 2[ 29] 17[ 24] 14[ 23] 22[ 326] 22[ 326] 21[ 34] 17[ 24] 17[ 24] 17[ 24] 17[ 24] 17[ 24] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 17[ 24] 17[ 24] 17[ 24] 17[ 24] 2[ 29] 2[ 29] 2[ 29] 2[ 29] 22[ 326] 22[ 326] 22[ 326] 22[ 326] 199,8 1 [ 1.26] 24 3 11 [ 14.8] 1 [ 13.4] 13 [ 17.4] 12 [ 16.1] 6 [ 1.8] 6 [ 1.8] 4 2,1 1 31,7 [ 19.26] 19 24 9 1 [ 13.4] 1,6[ 14.2] 6 [ 1.8] 3 1 [ 24.4] 1 19 4 [ 4] 4 [ 478] [ 487] 61 [ 4] [ 442] 61 [ 4] 69 [ 611] 69 [ 611] 6 [ 496] 71 [ 628] 84 [ 743] 87 [ 77] [ 73] [ 8] [ 12] [ 44] 7,8 [ 1.] 6 [ 1.8] 46 [ 47] [ 487] 66 [ 84] 61 [ 4] 3 397 41 [ 363] [ 442] [ 442] [ 442] 1 [ 44] 8,1 [ 18.9] 8, [ 18.7] 9,2 [ 2.3] 9,9 [ 21.8] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 34
R OTORS R FUNCTION DIAGRAS lb-i danm Q= l/mi 1.3 GP 1 l/mi 2.6 GP 1 l/mi 4. GP 2 l/mi.3 GP 2 l/mi 6.6 GP 3 l/mi 7.9 GP 3 l/mi 9.2 GP 4 l/mi 1.6 GP 4 l/mi 11.9 GP l/mi 13.2 GP 11 1 9 8 7 6 4 3 2 1 12 11 1 9 8 7 6 4 3 2 1 it.,kw 1kW 2kW 4kW 6kW 8kW p=17 bar 24 PSI 14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 7 bar 12 PSI bar 73 PSI 3 bar 43 PSI it. 1 2 3 4 6 7 8 9 1 RP R 8 lb-i danm Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 2 18 22 2 p=2 bar 29 PSI 16 18 17 bar 24 PSI 14 16 12 1 8 6 4 2 14 12 1 8 6 4 2 1 2 3 4 6 7 8 9 RP it. 14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 3 bar 43 PSI The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. 3
R OTORS R 1 FUNCTION DIAGRAS lb-i danm Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 2 28 2 1 1 24 2 16 12 it. p=2 bar 29 PSI 17 bar 24 PSI 14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 8 8 bar 116 PSI 4 6 bar 87 PSI it. 3 bar 43 PSI 1 2 3 4 6 7 RP R 12 lb-i danm Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 32 36 28 24 2 16 12 8 4 32 p=2 bar 29 PSI 28 24 2 16 12 8 4 it. 1 2 3 4 6 RP it. 17 bar 24 PSI 14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 3 bar 43 PSI The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. 36
R OTORS R 16 FUNCTION DIAGRAS lb-i 4 danm 44 Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 36 32 28 24 2 16 12 8 4 36 32 28 24 2 16 12 8 it. p=2 bar 29 PSI 17 bar 24 PSI 14 bar 23 PSI 12 bar 174 PSI 1 bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 4 4 it. 1 1 2 2 4 4 3 bar 43 PSI RP R 2 lb-i danm Q= l/mi 1.3 GP 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 4 4 3 3 2 2 1 4 4 3 3 2 2 1 it. p=2 bar 29 PSI 17 bar 24 PSI 14 bar 23 PSI 12 bar 174 PSI 1 bar 12 PSI 8 bar 116 PSI 1 1 6 bar 87 PSI it. 1 1 2 2 3 bar 43 PSI RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. 37
R OTORS R 2 FUNCTION DIAGRAS lb-i 6 4 4 3 3 2 2 1 1 danm 6 6 4 4 3 3 2 2 1 1 Q= l/mi 1.3 GP it. 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 2 7 1 12 1 17 2 22 2 27 3 it. p=2 bar 29 PSI 17 bar 24 PSI 14 bar 23 PSI 11 bar 16 PSI 1 bar 12 PSI 8 bar 116 PSI 6 bar 87 PSI 3 bar 43 PSI RP R 31 lb-i 6 6 4 4 3 danm 72 64 6 48 4 Q= l/mi 1.3 GP it. 1 l/mi 2.6 GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP p=17 bar 24 PSI 16 bar 232 PSI 13 bar 174 PSI 12 bar 181 PSI 3 2 2 1 1 32 24 16 8 it. 8 bar 116 PSI 6 bar 94 PSI 4 bar 6 PSI 3 bar 43 PSI 2 7 1 12 1 17 2 22 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. 38
R OTORS FUNCTION DIAGRAS R 4 lb-i danm Q= l/mi 1.3 GP 1 l/mi 2.6 GP 1 l/mi 4. GP 2 l/mi.3 GP 3 l/mi 7.9 GP 4 l/mi 1.6 GP l/mi 13.2 GP 6 l/mi 1.9 GP 7 l/mi 18. GP 7 l/mi 19.8 GP 6 64 2 48 44 4 36 32 28 24 2 16 12 8 4 6 6 2 48 44 4 36 32 28 24 2 16 12 8 4 it. p=12 bar 181 PSI 11 bar 16 PSI 9 bar 13 PSI 8 bar 116 PSI 6 bar 94 PSI bar 8 PSI 4 bar 8 PSI 3 bar 43 PSI 1 2 3 4 6 7 8 9 1 11 12 13 14 1 16 17 18 19 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o 1 bar [72. 14 PSI] ad oil with viscosity of 32 mm²/s [1 SUS] at C [122 F]. 39
R OTORS DIENSIONS AND OUNTING DATA SA Shaft SH Shaft K Shaft C Shaft CO Shaft SA Shaft SH Shaft K Shaft C Shaft CO Shaft max [2.16] max [2.16] Shaft Dim. See Page 28 max 49 [1.929] max 49 [1.929] max L 38±,1 [1.496±.9] P (A,B) Port A C Port B 74±,3 [2.913±.118] Flage Dim. See Page 41 max L P (A,B) 44±,1 [1.732±.9] Port A 8±,3 [3.149±.118] Port B C L1 Port Dim. See Page 41 L1 T max ø1 [ 4,134] max ø1 [ 4,134] E Rear ports OB Shaft KB Shaft CB Shaft HB Shaft max L max 7 [2.76] max 68,3 [2.689] SB Shaft max 14 [.1] mm [i] C P T (A, B) : 4x8-13 mm [.1 i] depth : 2xG1/2 or 2x22x1, - 1 mm [.9 i] depth : G1/4 or 14x1, - 12 mm [.47 i] depth (plugged) Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized - CW Type L, mm [i] Type L, mm [i] Type L, mm [i] Type L, mm [i] L, 1 mm[i] R(F) R(F) 8 R(F) 1 R(F) 12 R(F) 16 R(F) 2 R(F) 2 R(F) 31 R(F) 4 138, [.43] 143, [.63] 146, [.7] 1, [.93] 16, [6.16] 163, [6.44] 172, [6.77] 183, [7.2] 198, [7.8] RQ RQ 8 RQ 1 RQ 12 RQ 16 RQ 2 RQ 2 RQ 31 RQ 4 143, 148, 12, 16, 162, 169, 179, 189, 24, [.6] [.8] [.98] [6.16] [6.4] [6.67] [7.] [7.44] [8.3] R(F)E R(F)E 8 R(F)E 1 R(F)E 12 R(F)E 16 R(F)E 2 R(F)E 2 R(F)E 31 R(F)E 4 17, 162, 16, 17, 176, 183, 192, 24, 218, [6.2] [6.4] [6.2] [6.69] [6.93] [7.2] [7.6] [8.3] [8.8] RQE RQE 8 RQE 1 RQE 12 RQE 16 RQE 2 RQE 2 RQE 31 RQE 4 163,[6.44] 168,[6.63] 171,[6.7] 176,[6.93] 182,[7.17] 189,[7.44] 198,[7.8] 21,[8.27] 224,[8.82] 9, [.3] 14, [.] 17,4 [.69] 21,8 [.86] 27,8 [1.9] 34,8 [1.37] 43, [1.71] 4,8 [2.16] 69,4 [2.73] 4
R OTORS 2xø13,3 +,4 +.16 [.2 ] Oval out (2 Holes) OUNTING 8±,3 [.31±.118] 13 [.118] ø16,4±,2 [4.189±.79] F - Oval out (4 Holes) ±,1 [2.16±.39] max 17, [ 4,232] Q - Square out (4 Bolts) ±,1 [2.16±.39] ø82,±,1 [3.2±.39] mi 1 deep [.9] 82 [3.228] ø82,±, [3.248±.19] ø82,±, [3.248±.19] 16 [.63] 4 4xø13,3 +,4 +.16 [.2 ] ø16,4±,2 [4.189±.79] 8±,3 [.31±.118] 4x1 16 [.63] ø44,4±, [1.748±.19] 13 [.118] ±,1 [2.16±.39] max 17, [ 4,232] 82 [3.228] max 17, [ 4,232] 2,3±,3 [.98±.118] mm [i] PORTS Side Ports E Rear Ports 18±,1 [.78±.39] 2±,3 [.787±.118] C Port A 2±,3 [.787±.118] max 17, [ 4,232] ±,1 [2.16±.39] max L ±,1 [2.16±.39] 2 [.787] Port A 18±,1 [.78±.39] 2 [.984] 2±,3 [.787±.118] C P T (A, B) Port B 2±,3 [.787±.118] P (A,B) : 4x8-13 mm [.1 i] depth : 2xG1/2 or 2x22x1, - 1 mm [.9 i] depth : G1/4 or 14x1, - 12 mm [.47 i] depth (plugged) T 41 31,2 [1.23] Port B T Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized - CCW 7,1 [.279] P (A,B) [. 197] Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized - CW
R OTORS R ORDER CODE 1 2 3 4 6 7 8 9 1 Pos.1 - outig Flage omit - Oval mout, two holes F Q Pos.2 omit N Pos.3 - Port type omit E Pos.4 - Displacemet code 8 1 12 16 2 2 31 4 Pos. C VC CO VCO SH VSH K SA VSA CB KB SB OB HB - Oval mout, four holes - Square mout, four bolts - Optio (eedle bearigs) - oe - with eedle bearigs - Side ports - Rear ports - 1, cm /rev [ 3.14 i /rev] - 8,3 cm /rev [ 4.9 i /rev] - 99,8 cm /rev [ 6.9 i /rev] - 12,7 cm /rev [ 7.67 i /rev] - 19,6 cm /rev [ 9.74 i /rev] - 199,8 cm /rev [12.19 i /rev] - 2,1 cm /rev [1.26 i /rev] - 31,7 cm /rev [19.26 i /rev] - 397, cm /rev [24.4 i /rev] - Shaft Extesios *(see page 28) - ø2 straight, Parallel key A8x7x32 DIN688 - ø2 straight, Parallel key A8x7x32 DIN688 with corrosio resistat bushig - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 with corrosio resistat bushig - ø2,32 splied BS 29 (SAE 6B) - ø2,32 splied BS 29 (SAE 6B) with corrosio resistat bushig - ø28,6 tapered 1:1, Parallel key Bxx14 DIN688 - ø24, splied B 2x22 DIN 482 - ø24, splied B 2x22 DIN 482 with corrosio resistat bushig - ø32 straight, Parallel key A1x8x4 DIN688 - ø3 tapered 1:1, Parallel key B6x6x2 DIN688 - splied A 2x22 DIN 482 - ø1¼" tapered1:8, Parallel key "x "x1¼" BS46 - ø1¼" splied 14T ANSI B92.1-1976 Pos. 6 omit D U Pos. 7 omit 1 Pos. 8 omit Pos. 9 Pos.1 omit - Shaft Seal Versio (see page 3) - Low pressure shaft seal or Stadard shaft seal for... B shaft - Stadard shaft seal - High pressure shaft seal (without check valves) - Drai Port - with drai port - without drai port - Ports - BSPP (ISO 228) - etric (ISO 262) - Special Features (see page 119) - Desig Series - Factory specified NOTES: The followig combiatios are ot allowed: - Q flage with...b shafts; - N optio with...b shafts, Low Pressure Seal or U optio; -...B shafts with D ad U shaft seals. * The permissible output torque for shafts must ot be exceeded! The hydraulic motors are magao-phosphatized as stadard. 42
Hydraulic motors type R...T with tacho coectio A R motors are available i versio with tacho drive shaft. With tacho coectio the speed of the motor ca be registered. Tacho shaft has a 6 times higher revolutio speed tha output shaft ad opposite directio of rotatio. OUTLINE DIENSIONS REFERENCE B ø9 [.34] 6, [.26] 1,3 [.4] B 3±, [.118±.19] 22x1, ø3 [1.181] ø6 [2.362] A 26 [1.24] Drai port - G1/8 (1x1 for metric ports) mi 1 mm [.39 i] deep max L L1 26,4 [1.39] 39 [1.3] Type R R 8 R 1 R 12 R 16 R 2 R 2 R 31 R 4 L, mm [i] 17 162 16 17 176 183 192 24 218 [6.18] [6.38] [6.] [6.69] [6.93] [7.2] [7.6] [8.3] [8.8] L, 1 mm[i] 9, [.3] 14, [.] 17,4 [.69] 21,8 [.86] 27,8 [1.9] 34,8 [1.37] 43, [1.71] 4,8 [2.16] 69,4 [2.73] mm [i] Notes: Radial or axial load o tacho shaft must be avoided. ax. torque o tacho shaft,1 danm [.88 lb-i]. ax. retur pressure without drai lie 2 bar [29 PSI]. Tacho optio for R motor is available oly for shafts with sealig diameter ø28,6 with shaft seal type D (up to 1 bar). It is ot allowed for Q-flage. The mai techical features correspod to the stadard motors series R. There are o chages i the overall ad moutig dimesios. For detail techical ad moutig data please refer to R catalogue. 43
HYDRAULIC OTORS SP +S Hydraulic itroduces a ew versio of hydraulic motors, type SP with ew housig, itegrated output shaft to the spool valve, check valves, high pressure shaft seal. The SP motors are suitable for a wide rage of applicatios where compact ad high efficiet motors are required. CONTENTS Specificatio data...4 46 Fuctio diagrams...18 24 Dimesios ad moutig... 47 48 Shaft extesios... 48 Permissible shaft Seal Pressure... 48 Permissible shaft loads... 49 Order code... 49 APPLICATION» Coveyors» Feedig mechaism of robots ad maipulators» etal workig machies» Textile machies» Agriculture machies» Food idustries» Grass cuttig machiery etc. OPTIONS» odel- Spool valve, gerotor» Flage mout - 2 hole oval flage; square flage» Side BSPP ports» Shafts- straight ad splied» Shaft seal for high ad low pressure» Other special features GENERAL ax. Displacemet, ax. Speed, ax. Torque, ax. Output, ax. Pressure Drop, ax. Oil Flow, i. Speed, Pressure fluid Temperature rage, cm /rev [i /rev] [RP] danm [lb-i] kw [HP] bar [PSI] lpm [GP] [RP] O C [ F] 2 Optimal Viscosity rage, mm /s [SUS] Filtratio O 396 [24.16] 11 :38 [ 336] it.: 46 [324] 17, [23.] :14 [ 23] it.:17 [24] 7 [ 19.8] 1 ieral based- HLP(DIN 124) or H(ISO 6743/4) -3 9 [-22 194] 2 7 [ 98 347] ISO code 2/16 (i. recommeded fluid filtratio of 2 micro) Pressure drop bar [ PSI] 1 [14] 14 [ 23] Oil flow i drai lie Viscosity Oil flow i drai lie 2 mm /s [ SUS] lpm [ GP] 2 [ 98] 3 [ 164] 2 [98] 3 [164] 2, [.66] 1,8 [.476] 3, [.92] 2,8 [.74] p bar 3 2 2 1 1 p PSI 4 3 2 1 Pressure Losses 2 4 6 8 1 12 14 16 18 2 Q, GP 1 2 3 4 6 7 8 Q, lpm 44
SP OTORS SPECIFICATION DATA Specificatio Data for SP... motors with Cad COshafts. Type SP SP 8 SP 1 SP 12 SP 16 SP 2 SP 2 SP 31 SP 4 Displacemet, cm³/rev [ i³/rev] 49, [ 3.] 79,2 [4.83] 99 [6.4] 123,8 [7.] 18,4 [9.66] 198 [12.1] 247, [1.1] 316,8 [19.3] 396 [2416] ax. Speed, 121 7 6 486 378 33 242 19 1 [RP] 11 94 7 6 472 378 33 236 189 ax. Torque 9,4 [83] 1,1 [134] 19,3 [171] 23,7 [21] 3 [26] 3 [26] 27,6 [2442] 29, [261] 28, [222] danm [ lb-i] 11,9 [1] 19, [172] 23,7 [21] 29,8 [264] 37,8 [334] 36, [323] 3, [3142] 36,6 [47] 36 [318] 14 [124] 22 [19] 27 [239] 36, [323] 42 [3717] 3 [469] 4 [478] 9 [222] 9 [222] ax. Output 9,9 [13.3] 9,9 [13.3] 9,9 [13.3] 9,9 [13.3] 9,9 [13.3] 9, [12.7] 6 [8.1] 4 [.4] 3 [4] kw [ HP] 12, [16.8] 12, [16.8] 12, [16.8] 12, [16.8] 12, [16.8] 12, [16.8] 13,2 [17.7],8 [7.8] [6.7] ax. Pressure Drop 14 [23] 14 [23] 14 [23] 14 [23] 14 [23] 11 [167] 8 [1233] 7 [11] [798] bar [ PSI] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 14 [23] 11 [14] 9 [13] 7 [11] 18 [261] 16 [232] 13 [188] ax. Oil Flow 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] lpm [ GP] ax. Startig Pressure with Uloaded Shaft, bar [PSI] 1 [14] 1 [14] 1 [14] 9 [131] 8 [116] 7 [1] 6 [87] [73] [73] i. Startig Torque, danm [lb-i] 7,7 [682] 14 [124] 16,8 [149] 21 [186] 28 [2478] 28, [222] 26, [234] 26, [234] 26, [234] ax. Ilet Pressure 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] bar [ PSI] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 4
SP OTORS SPECIFICATION DATA Specificatio Data for SP... motors with SH shafts. Type SP SP 8 SP 1 SP 12 SP 16 SP 2 SP 2 SP 31 SP 4 Displacemet, cm³/rev [ i³/rev] 49, [ 3.] 79,2 [4.83] 99 [6.4] 123,8 [7.] 18,4 [9.66] 198 [12.1] 247, [1.1] 316,8 [19.3] 396 [2416] ax. Speed, 121 7 6 486 378 33 242 19 1 [RP] 11 94 7 6 472 378 33 236 189 ax. Torque 9,4 [83] 1,1 [134] 19,3 [171] 23,7 [21] 3 [26] 36,6 [324] 38 [336] 38 [336] 36 [319] danm [ lb-i] 11,9 [1] 19, [172] 23,7 [21] 29,8 [264] 37,8 [334] 4,6 [43] 4 [398] 46 [324] 46 [324] 14 [124] 22 [19] 27 [239] 36, [323] 42 [3717] 3 [469] 67 [93] 8 [723] 8 [723] ax. Output 9,9 [13.3] 9,9 [13.3] 9,9 [13.3] 9,9 [13.3] 9,9 [13.3] 1,3 [13.8] 8 [1.7] 6 [8.1] 4,8 [6.4] kw [ HP] 12, [16.8] 12, [16.8] 12, [16.8] 12, [16.8] 12, [16.8] 1,3 [2.] 17, [23.] 8,2 [1.9] 9,2 [12.3] ax. Pressure Drop 14 [23] 14 [23] 14 [23] 14 [23] 14 [23] 14 [23] 11 [14] 9 [13] 7 [11] bar [ PSI] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 14 [23] 14 [23] 9 [13] 18 [261] ax. Oil Flow 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] 6 [1.9] lpm [ GP] ax. Startig Pressure with Uloaded Shaft, bar [PSI] 1 [14] 1 [14] 1 [14] 9 [131] 8 [116] 7 [1] 6 [87] [73] [73] i. Startig Torque, danm [lb-i] 7,7 [682] 14 [124] 16,8 [149] 21 [186] 28 [2478] 34,6 [362] 34, [3] 3 [398] 3 [398] ax. Ilet Pressure 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] bar [ PSI] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 46
SP OTORS DIENSIONS AND OUNTING DATA SP SPQ CO Shaft SH Shaft C Shaft CO Shaft SH Shaft C Shaft max 3, [2.1] max L P (A,B) Port A Port B max 3, [2.11] L1 4,8±,1 [2.16±.6] 8±,1 [.32±.6] max L max [1.97] max 4 [1.77] max [1.97] 6±,1 [2.36±.6] 2±,1 [.787±.4] 2±,1 [.787±.4] ø83 [3.267] ø8 [3.346] T P T Type SP SP 8 (A,B) SP 1 SP 12 SP 16 SP 2 SP 2 SP 31 SP 4 : 2xG1/2-18 mm [.79 i] depth : G1/4-12 mm [.47 i] depth L max, mm [i] 128 [.4] 132 [.19] 134, [.29] 138 [.43] 142, [.61] 148 [.83] 14, [6.8] 164 [6.46] 174, [6.87] Type SPQ SPQ 8 SPQ 1 SPQ 12 SPQ 16 SPQ 2 SPQ 2 SPQ 31 SPQ 4 L max, mm [i] 134 [.28] 138 [.43] 14,9 [.] 144 [.67] 148,9 [.86] 14 [ 6.6] 16,9 [6.33] 17 [6.69] 18,9 [7.12] L, 1 mm [i] 6,67 [.26] 1,67 [.42] 13,33 [.2] 16,67 [.66] 21,33 [.84] 26,67 [ 1.] 33,33 [1.31] 42,67 [1.68] 3,33 [2.1] Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized - CW mm [i] 47
SP OTORS OUNTING Oval out (2 Holes) Q Square out (4 bolts) 82 [3.228] 2,±,3 [.98±.118] 78 [3.71] 3,2±,1 [2.9±.6] 3,2±,1 [2.9±.6] max 13 [.12] ø82,±, [3.248±.19] 78 [3.71] 82 [3.228] ø44,4±, [1.7±.19] 2xø13,3 +,4 +,17 [.3 ] [2.17] 16,±, [.6±.19] 8±,3 [.31±.118] [2.16] ø82,±,1 [3.2±.39] mi 17 [.669] 4x3/8-16 UNC 1 [3.94] SHAFT EXTENSIONS C - ø2 straight, Parallel key A8x7x3 DIN 688 ax. Torque 34 danm [31 lb-i] CO - ø1" straight, Parallel key ¼"x¼"x1" BS46 ax. Torque 34 danm [31 lb-i] 8 -,36 [.31 ] -.14 6, [.26] 6,4 -, [.22-.2] 7 [.276] 27-,3 [1.6 ] -.118 ø28,6 [1.124] ø2-,21 [.98 ] -.8 28 -,3 [1.1 ] -.118 ø28,6 [1.124] ø2,4-,2 [1 ] -.98 8 mi 22 Deep [.866] 43 [1.69] 1/4-2UNC-2B mi 22 Deep [.866] 43 [1.69] (4 [1.7]- for SPQ...CO) SH - splied, BS 29 (SAE 6B) ax. Torque 4 danm [34 lb-i] AX. PERISSIBLE SHAFT SEAL PRESSURE A ax retur pressure without drai lie or max. pressure i drai lie -,8 ø21,47 -,12 -.31 [.84 -.49] 8 mi 22 Deep [.866] A-A ø2,3 -,1 -,1 [.996 ] -.39 -.9 6,2-, [.246-.2 ] ø3 [1.378] 1,3 [.1] 26, +,3 [1.4 +.118 ] 43 [1.69] A 7±,1 [.28±.39] ø23,9-,1 [.94 ] -.9 P bar 2 1 1 1 P PSI 3 2 2 1 1 14 1 2 1 2 - cotiuous operatios - itermittet operatios 4 6 1: Curve for Stadard Shaft Seal 8 1 RP mm [i] 2: Curve for High Pressure Seal ("U" Seal) 48
SP OTORS PERISSIBLE SHAFT LOADS Prad Oval out Radial Shaft Load Prad for C, CO Shaft Extesios by L=3 mm [1.18 i] (24 mm [.94 i]) P max= 1 dan [ 33 lbs] L= 3 [ 1.18] The permissible radial shaft load depeds o Speed () Distace (L) from the poitload to the moutig flage outig flage versio 8 Oval mout: P rad = x 243 [dan]* 91,+L P max= 2 dan [ 44 lbs] Prad Square out 8 x 21 [ RP 3.6+L [lbs] 8 Square mout: P rad = x 243 [dan]* 97,+L P rad dan P rad lbs L= 24 [.94] 8 x 21 [ RP 3.84+L [lbs] 9 8 6 4 2 16 12 8 2 4 [ [ * <_ 2RP; max P =8 dan [18lbs] rad <_ 2RP; L< mm [2.2 i] 2 4 6 8 RP ORDER CODE 1 2 3 4 6 SP Pos.1 - outig Flage omit - Oval mout, two holes Q - Square mout, four bolts - 3/8-16 UNC Pos.2 - Displacemet code* - 49, cm /rev [ 3.2 i /rev] 8-79,2 cm /rev [ 4.83 i /rev] 1-99, cm /rev [ 6.4 i /rev] 12-123,8 cm /rev [ 7. i /rev] 16-18,4 cm /rev [ 9.66 i /rev] 2-198, cm /rev [12.1 i /rev] 2-247, cm /rev [1.1 i /rev] 31-316,8 cm /rev [19.3 i /rev] 4-396, cm /rev [24.16 i /rev] Pos.3 - Shaft Extesios** C CO SH Pos.4 - Shaft Seal Versio omit U Pos. Pos.6 - Desig Series omit - ø2 straight, Parallel key A8x7x3 DIN688 1 1 1 - ø1" straight, Parallel key / "x / "x1 / " BS46 4 4 4 - ø2,3 splied, BS 29 (SAE 6B) - Stadard shaft seal - High pressure shaft seal - Special Features (see page 119) - Factory specified N OTES: * ** For the Fuctio Diagrams data please look at "+S Hydraulic" Catalogue for P motors, pages 18 24. The permissible output torque for shafts must ot be exceeded! The hydraulic motors are magao-phosphatized as stadard. 49
HYDRAULIC OTORS SR +S Hydraulic itroduces a ew versio of hydraulic motors, type SR with ew housig, itegrated output shaft to the spool valve, check valves, high pressure shaft seal. The SR motors are suitable for a wide rage of applicatios where compact ad high efficiet motors are required. CONTENTS Specificatio data...1 3 Fuctio diagrams... 3 39 Dimesios ad moutig... 4 6 Shaft extesios... 7 Permissible shaft Seal Pressure... 7 Permissible shaft loads... 8 Order code... 8 APPLICATION» Coveyors» Feedig mechaism of robots ad maipulators» etal workig machies» Textile machies» Agriculture machies» Food idustries» Grass cuttig machiery etc. OPTIONS» odel - Spool valve, geroller» Flage mout - 2 hole oval flage; 6 hole oval flage; square flage» Side BSPP ports» Shafts- straight, splied ad tapered» Shaft seal for high ad low pressure» Other special features GENERAL ax. Displacemet, ax. Speed, ax. Torque, ax. Output, ax. Pressure Drop, ax. Oil Flow, i. Speed, Pressure fluid Temperature rage, cm /rev [i /rev] [RP] danm [lb-i] kw [HP] bar [PSI] lpm [GP] [RP] O C [ F] 2 Optimal Viscosity rage, mm /s [SUS] Filtratio O 397 [24.4] 97 : 6 [31] it.: 69 [617] 1 [2.1] : 17 [24] it.: 2 [29] 7 [ 19.8] 1 ieral based- HLP(DIN 124) or H(ISO 6743/4) -3 9 [-22 194] 2 7 [ 98 347] ISO code 2/16 (i. recommeded fluid filtratio of 2 micro) Pressure drop bar [ PSI] 1 [14] 14 [ 23] Oil flow i drai lie Viscosity Oil flow i drai lie 2 mm /s [ SUS] lpm [ GP] 2 [ 98] 3 [ 164] 2 [98] 3 [164] 2, [.66] 1,8 [.476] 3, [.92] 2,8 [.74] p bar 3 2 2 1 1 p PSI 4 3 2 1 Pressure Losses 2 4 6 8 1 12 14 16 18 2 Q, GP 1 2 3 4 6 7 8 Q, lpm
SR OTORS SPECIFICATION DATA Specificatio Data for SR... motors with Cad COshafts. Type SR SR 8 SR 1 SR 12 SR 16 SR 2 SR 2 SR 31 SR 4 Displacemet, cm³/rev [ i³/rev] 1, [3.14] 8,3 [4.9] 99,8 [6.9] 12,7 [7.67] 19,6 [9.74] 199,8 [12.19] 2,1 [1.26] 31,7 [19.26] 397 [24.4] ax. Speed, 77 7 6 47 37 3 24 19 1 [RP] 97 94 7 6 47 37 3 24 19 ax. Torque 1 [9] 2 [177] 24 [212] 3 [26] 29 [266] 29 [266] 3 [26] 3 [26] 3 [26] danm [ lb-i] 13 [11] 22 [1947] 28 [248] 34 [31] 39 [34] 39 [34] 39 [34] 42 [3717] 4 [34] 17 [1] 27 [239] 32 [2832] 37 [327] 46 [47] 6 [496] 6 [31] 61 [4] 61 [4] ax. Output 7 [9,4] 12, [17] 13 [17.4] 12, [17] 9 [12] 7, [1] 6 [8.1] [6.7] 3,8 [.1] kw [ HP] 8, [11,4] 1 [2.1] 1 [2.1] 14, [19.] 12, [17] 1 [13.4] 8 [1.7] 6, [8.7] 6,1 [8.2] ax. Pressure Drop 14 [23] 17 [24] 17 [24] 17 [24] 12 [174] 1 [12] 8 [116] 7 [11] [798] bar [ PSI] 17 [24] 2 [29] 2 [29] 2 [29] 17 [24] 14 [23] 11 [16] 1 [14] 7 [11] 2 [29] 1 [217] 11 [1668] ax. Oil Flow 4 [1.] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] lpm [ GP] [13.2] ax. Startig Pressure with Uloaded Shaft, bar [PSI] 1 [14] 1 [14] 1 [14] 9 [13] 7 [12] [73] 4 [8] 3 [43.] 3 [43.] i. Startig Torque, danm [lb-i] 8 [71] 1 [133] 2 [177] 24 [2124] 23 [23] 23 [23] 24 [2124] 26 [23] 26 [23] ax. Ilet Pressure 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] bar [ PSI] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 1
SR OTORS SPECIFICATION DATA Specificatio Data for SR... motors with SH shafts. Type SR SR 8 SR 1 SR 12 SR 16 SR 2 SR 2 SR 31 SR 4 Displacemet, cm³/rev [ i³/rev] 1, [3.14] 8,3 [4.9] 99,8 [6.9] 12,7 [7.67] 19,6 [9.74] 199,8 [12.19] 2,1 [1.26] 31,7 [19.26] 397 [24.4] ax. Speed, 77 7 6 47 37 3 24 19 1 [RP] 97 94 7 6 47 37 3 24 19 ax. Torque 1 [9] 2 [177] 24 [212] 3 [26] 39 [34] 38, [341] 38[336] 39 [34] 38[336] danm [ lb-i] 13 [11] 22 [1947] 28 [248] 34 [31] 43 [38] 46 [47] 47 [416] 48 [4248] 47 [416] 17 [1] 27 [239] 32 [2832] 37 [327] 46 [47] 6 [496] 6 [31] 61 [4] 61 [4] ax. Output 7 [9,4] 12, [17] 13 [17.4] 12, [17] 11, [1.4] 9 [12] 8 [1.7] [6.7] 4,8 [6.4] kw [ HP] 8, [11,4] 1 [2.1] 1 [2.1] 14, [19.] 14 [18.8] 12 [16.1] 9, [12.7] 8 [1.7] 6,8 [9.1] ax. Pressure Drop 14 [23] 17 [24] 17 [24] 17 [24] 17 [24] 14 [23] 11 [16] 8 [1232] 7 [11] bar [ PSI] 17 [24] 2 [29] 2 [29] 2 [29] 2 [29] 17 [24] 14 [23] 11 [1668] 9 [13] 2 [29] 1 [217] 11 [1668] ax. Oil Flow 4 [1.] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] 6 [1.8] lpm [ GP] [13.2] ax. Startig Pressure with Uloaded Shaft, bar [PSI] 1 [14] 1 [14] 1 [14] 9 [13] 7 [12] [73] 4 [8] 3 [43.] 3 [43.] i. Startig Torque, danm [lb-i] 8 [71] 1 [133] 2 [177] 24 [2124] 32 [2832] 33 [292] 31 [274] 31, [2788] 31, [2788] ax. Ilet Pressure 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] 17 [24] bar [ PSI] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 2
SR OTORS SPECIFICATION DATA Specificatio Data for SR... motors with K, CB, CAshafts. Type Displacemet, cm³/rev [ i³/rev] ax. Speed, [RP] ax. Torque danm [ lb-i] ax. Output kw [ HP] ax. Pressure Drop bar [ PSI] ax. Oil Flow lpm [ GP] ax. Startig Pressure with Uloaded Shaft, bar [PSI] i. Startig Torque, danm [lb-i] ax. Ilet Pressure bar [ PSI] SR 1, [3.14] 8,3 [4.9] 99,8 [6.9] 12,7 [7.67] 19,6 [9.74] 199,8 [12.19] 2,1 [1.26] 77 97 1 [9] 13 [11] 17 [1] 7 [9,4] 8, [11,4] 4 [1.] [13.2] 1 [14] 8 [71] SR 8 7 94 2 [177] 22 [1947] 27 [239] 12, [17] 1 [2.1] 6 [1.8] 1 [14] 1 [133] SR 1 6 7 24 [212] 28 [248] 32 [2832] 13 [17.4] 1 [2.1] 6 [1.8] 1 [14] 2 [177] SR 12 47 6 3 [26] 34 [31] 37 [327] 12, [17] 14, [19.] 14 [23] 17 [24] 17 [24] 17 [24] 17 [24] 2 [29] 2 [29] 2 [29] 6 [1.8] 9 [13] 24 [2124] 17 [24] 17 [24] 17 [24] 17 [24] 2 [29] 2 [29] 2 [29] 2 [29] SR 16 37 47 39 [34] 43 [38] 46 [47] 11, [1.4] 14 [18.8] 17 [24] 2 [29] 6 [1.8] 7 [12] 32 [2832] 17 [24] 2 [29] SR 2 3 37 4 [3983] [442] 6 [496] 11 [14.7] 13 [17.4] 17 [24] 2 [29] 6 [1.8] [73] 41 [363] 17 [24] 2 [29] SR 2 24 3 7 [ 4] 61 [4] 71 [6284] 1 [13.4] 12 [16.1] 17 [24] 2 [29] 6 [1.8] 4 [8] [442] 17 [24] 2 [29] SR 31 31,7 [19.26] 19 24 7 [ 4] 69 [617] 84 [7434] 9 [12] 1 [13.4] 13 [198] 17 [24] 21 [34] 6 [1.8] 3 [43.] [442] 17 [24] 2 [29] SR 4 397 [24.4] 1 19 6 [31] 69 [617] 87 [87] 7,8 [1.] 1,6 [14.2] 11 [16] 14 [23] 17 [24] 6 [1.8] 3 [43.] [442] 17 [24] 2 [29] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 3
SR OTORS DIENSIONS AND OUNTING DATA SR SRQ CO Shaft SH Shaft C Shaft CO Shaft SH Shaft C Shaft 4,7±,1 [2.14±.6] max [2.16] max [2.16] max L Port A Port B 8±,1 [.32±.6] 2±,1 [.787±.4] 2±,1 [.787±.4] L1 max 49 [1.93] max 49 [1.93] P (A,B) 6,8±,1 [2.394±.6] max L ø1 [3.937] T P T (A,B) Type SR(F) SR(F) 8 SR(F) 1 SR(F) 12 SR(F) 16 SR(F) 2 SR(F) 2 SR(F) 31 SR(F) 4 : 2xG1/2-18 mm [.79 i] depth : G1/4-12 mm [.47 i] depth L, max mm [i] 138 [.43] 143 [.63] 146, [.77] 11 [.94] 17 [6.18] 164 [6.46] 172, [6.79] 184 [7.24] 198, [7.81] Type SRQ SRQ 8 SRQ 1 SRQ 12 SRQ 16 SRQ 2 SRQ 2 SRQ 31 SRQ 4 L, max mm [i] 144 [.67] 149 [.87] 12,6 [6.] 17 [6.18] 163 [6.42] 17 [6.69] 178, [7.3] 19 [7.48] 2, [8.9] L, 1 mm [i] 9, [.3] 14, [.] 17,4 [.69] 21,8 [.89] 27,8 [1.9] 34,8 [ 1.37] 43, [1.71] 4,8 [2.16] 69,4 [2.73] Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized - CW mm [i] 4
SR OTORS DIENSIONS AND OUNTING DATA SRF... KB Shaft CB Shaft CA Shaft C Shaft SH Shaft CO Shaft max 68, [2.696] max 9 [2.323] ±,1 [2.16±.6] max 68,2 [2.68] mm [i] max L max [2.16] Type L, max mm [i] SR(F) T SR(F) 8 T SR(F) 1 T SR(F) 12 T SR(F) 16 T SR(F) 2 T SR(F) 2 T SR(F) 31 T SR(F) 4 T 17 [6.18] 162 [6.38] 166 [6.3] 17 [6.69] 176 [6.93] 183 [7.2] 191 [7.2] 23 [7.99] 217 [8.4] L, 1 mm [i] 9, [.3] 14, [.] 17,4 [.69] 21,8 [.89] 27,8 [1.9] 34,8 [ 1.37] 43, [1.71] 4,8 [2.16] 69,4 [2.73] SR(F)...T 6, [.26] 1,3 [.41] 22x1, ø3 [1.18] ø6 [2.362] ø1 [3.937] 3±, [.118 ±.19] 4 o 6 o for F mout ø9 [.3] 26 [1.24] T max L L1 26,4 [1.4] 39 [1.4] T : G1/8-1 mm [.39 i] depth for SR(F)...T
SR OTORS OUNTING Oval out (2 Holes) 78 [3.71] 3,2±,1 [2.9±.6] 3,2±,1 [2.9±.6] max 13 [.12] ø82,±, [3.248±.19] 2xø13,3 +,4 +,17 [.3 ] [2.17] 1[ 4.13] 16,±, [.6±.197] 8±,3 [.31±.118] F Oval out (6 holes) 1[ 4.13] [2.17] 78 [3.71] max 13 [.12] ø82,±, [3.248±.19] 6xø13,3 +,4 +,17 [.3 ] 4 o 16,±, [.6±.197] 8±,3 [.31±.118] Q Square out (4 bolts) 82 [3.228] 2,±,3 [.98±.118] 78 [3.71] 82 [3.228] ø44,4±, [1.7±.19] [2.16] ø82,±,1 [3.2±.39] mi 17 [.669] 4x3/8-16 UNC 1 [4.134] mm [i] 6
SR OTORS SHAFT EXTENSIONS 8 -,36 [.31 ] -.14 C - ø2 straight, Parallel key A8x7x3 DIN 688 ax. Torque 34 danm [31 lb-i] 6, [.26] CO - ø1" straight, Parallel key ¼"x¼"x1 ¼" BS46 ax. Torque 34 danm [31 lb-i] 6,4 -, [.22-.2] [.197] 28-,3 [1.12 ] -.118 ø28,6 [1.124] +,1 ø2 +,2 [.98 ] -.9 -.7 28-,3 [1.12 ] -.118 ø28,6 [1.124] ø2,4-,2 [1 ] -.79 8 mi 22 Deep [.866] 43,2 [1.7] 8 mi 22 Deep [.866] 43,2 [1.7] SH - splied, BS 29 (SAE 6B) ax. Torque 4 danm [34 lb-i] -,8 ø21,6 -,12 -.31 [.8 -.49 ] 8 mi 22 deep [.866] A-A ø2,3 -,1 -,1 6,2-, [.996 ] -.39 -.9 [.246-.2 ] ø3 [1.378] 8,1±,1 [.32±.39] 1,3 [.1] 27,4 +,3 [1.79 +.118] 43,2 [1.7] A A ø23,9-,1 [.94 ] -.9 3-,3 1 -,4 [.394 ] -.16 [1.377 ] -.118 CB - ø32 straight, Parallel key 1x8x4 DIN 688 ax. Torque 77 danm [681 lb-i] (for F-flage oly) 8 mi 22 deep [.866] ø3 [1.378] 6,4±,7 [2.22±.28] +,18 ø32 +,2 [1.26 ] +.7 +.7 K - tapered 1:1, Woodruff key 6x9 DIN 6888 ax. Torque 9 danm [841 lb-i] (for F-flage oly) A-A 6 -,3 [.236 ] -.118 6x9 DIN 6888 36 [1.417] 8 [2.283] A,8±,2 [.228±.787] CA - ø1 1/4" straight, Parallel key / "x 16 / 16"x1 ¼" BS46 ax. Torque 77 danm [681 lb-i] (for F-flage oly) -,4 8 -,6 -.16 [.31 -.24 ] 19 -,3 [.748 ] -.118 ø3 [1.378] 1:1 A 4 [.17] 2x1, ø43, [1.71] ø4,±,1 [.177±.39] S=41, Tighteig torque 2±1 danm [177±88 lb-i] 3 [1.28 ] -,1 -,2 -.39 -.787 ø3 [1.378] 3/8-16 UNC ANSI B1.1-1982 47,±, [1.87±.19] ø31,7 -,2 [1.2 ] -.7 P bar 2 1 1 1 P PSI 3 2 2 1 1 14 1 2 3 1 2 4 AX. PERISSIBLE SHAFT SEAL PRESSURE 6 8 1 RP ax retur pressure without drai lie or max. pressure i drai lie - cotiuous operatios - itermittet operatios mm [i] 1: Curve for Stadard Shaft Seal for K, CA, CB shafts 2: Curve for Stadard Shaft Seal for C, CO, SH shafts 3: Curve for High Pressure Seal ("U" Seal) for C, CO, SH shafts. Not applicable for K, CA ad CB shafts! 7
SR OTORS Oval out Permissible Shaft Loads SR Prad 8 x 2 9+L, dan* P max= 1 dan [ 33 lbs] L= 3 [ 1.18] [ 8 221 x RP 3.74+L,lbs* [ P rad dan 9 8 6 4 2 P rad lbs 2 16 12 P max= 2 dan [ 44 lbs] 8 4 Prad Square out L= 24 [.94] 2 4 6 8 [ 8 x RP 2, dan* 11+L 8 221 x,lbs* RP 3.98+L [ Radial Shaft Load Prad for C, CO Shaft Extesios by L=3 mm [1.18 i] (24 mm [.94 i]) The permissible radial shaft load Prad depeds o the speed, RP, distace L from the poit of load to the moutig flage ad shaft versio. * < _ 2 RP; max Prad=8 dan [18 lbs] >2 _ RP; L < mm [2.2 i] Pos.1 - outig Flage omit F Q SR Pos.2 - Displacemet code** 8 1 12 16 2 2 31 4 Pos.3 C CO SH K* CA* CB* - 1, cm /rev [ 3.14 i /rev] - 8,3 cm /rev [ 4.9 i /rev] - 99,8 cm /rev [ 6.9 i /rev] - 12,7 cm /rev [ 7.67 i /rev] - 19,6 cm /rev [ 9.74 i /rev] - 199,8 cm /rev [12.19 i /rev] - 2,1 cm /rev [1.26 i /rev] - 31,7 cm /rev [19.26 i /rev] - 397, cm /rev [24.4 i /rev] - Shaft Extesios** - ø2 straight, Parallel key A8x7x3 DIN688 1 1 1 - ø1" straight, Parallel key / "x / "x1 / " BS46 4 4 4 - ø2,3 splied, BS 29 (SAE 6B) - tapered 1:1, Woodruff key 6x9 DIN 6888 - - 1 2 3 4 6 7 - Oval mout, two holes - Oval mout, six holes - Square mout, four bolts - 3/8-16 UNC ø1 1/4" straight, Parallel key / "x / "x1¼" Bs46 16 16 ø32 straight, Parallel key 1x8x4 DIN 688 ORDER CODE Pos.7 - Desig Series 8 Pos.4 - Shaft Seal Versio omit U omit T Pos.6 omit - Stadad shaft seal - High pressure shaft seal (Not for K, CA, CB Shafts) Pos. - Tacho Coectio*** - Without Tacho Coectio - With Tacho Coectio (Not for Qflage ad K, CA, CB shafts) - Special Features (see page 119) - Factory specified N OTES: * For F -flage oly! ** The permissible output torque for shafts must ot be exceeded! *** Radial or axial load o tacho shaft must be avoided. ax. torque o tacho shaft,1 danm [.88 lb-i]. ax. retur pressure without drai lie 2 bar [29 PSI]. For the Fuctio Diagrams data please look at "+S Hydraulic" Catalogue for R motors, pages 3 39. The hydraulic motors are magao-phosphatized as stadard.
HYDRAULIC OTORS RNA APPLICATION» Actuator motor as drivig-motor for steerig mechaism of the the three-wheel vehicles;» For coveyors (series coectio);» Dosig motor etc. A B RNA is suitable for drive mechaism where smooth operatio low speed ad high pressure is demaded. It is desiged with separated output shaft ad spool valve ad ca be specified with low iteral leakage. T L» Good start-up characteristics;» Precise cotrol of the Torque at low small flow.» Smooth operatio at high pressure ad small oil flow;» High volumetric efficiecy. Hydraulic Reservoir P R The mai techical features correspod to the stadard motors series R ø28,6 [1.124 i.] sealig diameter. There are o chages i the overall ad moutig dimesios. For detailed techical ad moutig data please refer to R catalogue. SPECIFICATION DATA Code RNA RNA 8 RNA 1 RNA 12 RNA 16 RNA 2 RNA 2 RNA 31 RNA 4 Displacemet 3 cm /rev 3 [i /rev] 1, [3.14] 8,3 [4.9] 99,8 [6.9] 12,7 [7.67] 19,6 [9.74] 199,8 [12.19] 2,1 [1.26] 31,7 [19.26] 397, [24.4] ax. ax. Torque ax. Output ax. Pressure ax. Oil Speed danm [lb-i] kw [HP] Drop, bar [PSI] Flow, lpm [RP] C, CO shafts SH, SA shafts C, CO shafts SH, SA shafts C, CO shafts SH, SA shafts [GP] it* it* it* it* it* it* 2 1 13 1 13 2, 2, 2, 2, 14 17 14 17 1, [88] [11] [88] [11] [2.68] [3.3] [2.68] [3.3] [23] [24] [23] [24] [2.8] 2 2 22 2 22 3, 3, 3, 3, 17 2 17 2 16 [177] [194] [177] [194] [4.2] [4.69] [4.2] [4.69] [24] [29] [24] [29] [4.2] 2 24 28 24 28 4,, 4,, 17 2 17 2 2 212 [248] 212 [248] [6.3] [6.71] [6.3] [6.71] [24] [29] [24] [29] [.3] 2 4 4, 6,, 6, 17 2 17 2 2 [26] [3] [26] [3] [7.37] [8.] [7.37] [8.] [24] [29] [24] [29] [6.6] 2 29 39 39 43, 6, 6, 7, 12 17 17 2 32 [26] [34] [34] [38] [6.71] [8.] [8.] [1.] [174] [24] [24] [29] [8.] 2 29 38, 38, 46, 7, 6, 9, 1 14 14 17 4 [26] [34] [34] [47] [6.71] [9.39] [8.72] [12.6] [12] [23] [23] [24] [1.] 2 9 39 47, 7, 6, 9, 8 11 11 14 [26] [34] [34] [416] [6.71] [9.39] [8.] [12.6] [116] [16] [16] [23] [13.2] 19 3 42 36 47, 7, 6, 8, 7 1 8 11 6 [26] [372] [34] [416] [6.71] [1.] [8.] [11.4] [12] [14] [123] [167] [17.2] 1 3 4 38 47 4, 6, 6, 7, 7 6 9 6 [26] [34] [326] [416] [[.36] [8.72] [8.] [9.39] [8] [11] [94] [13] [1.8] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. 9
HYDRAULIC OTORS RFL The hydraulic motors type RFL... ad LHRFL... are desiged to be used i operatig modes with peak radial loads of the output shaft (especially at startig ad stoppig) at direct drive of wheels or mechaisms (without clutch or gearbox). The radial loads are bore by a radial ball bearig which is mouted o the shaft of the hydraulic motor. The mai techical features correspod to the stadard motors series RF ø3 mm [1.378 i] sealig diameter. There are o chages i the overall ad moutig dimesios. For detailed techical ad moutig data please refer to R catalogue. A Versio D With Dust Seal PERISSIBLE SHAFT LOADS AX. PERISSIBLE SHAFT SEAL PRESSURE Pr dan 12 1 8 3 2. 2 1. 1. - 1. i Prad lbs 3 2 2 P bar 1 1 P PSI 2 1 1 6 1 1 2 3 4 6 7 8, RP 4 2 1 - cotiuous operatios - itermittet operatios 7 6 4 3 2 1-1 mm 6
RFL OTORS ORDER CODE R 1 2 3 4 6 7 8 9 1 Pos.1 - outig Flage F - Oval mout, four holes Pos.2 L Pos.3 - Port type omit E Pos.4 - Displacemet code 8 1 12 16 2 2 31 4 - Optio (bearigs) - with ball bearig - Side ports - Rear ports - 1, cm /rev [ 3.14 i /rev] - 8,3 cm /rev [ 4.9 i /rev] - 99,8 cm /rev [ 6.9 i /rev] - 12,7 cm /rev [ 7.67 i /rev] - 19,6 cm /rev [ 9.74 i /rev] - 199,8 cm /rev [12.19 i /rev] - 2,1 cm /rev [1.26 i /rev] - 31,7 cm /rev [19.26 i /rev] - 397, cm /rev [24.4 i /rev] Pos. - Shaft Extesios *(see page 28) CB KB SB OB HB Pos. 6 omit D Pos. 7 omit 1 Pos. 8 omit Pos. 9 omit - ø32 straight, Parallel key A1x8x4 DIN688 - ø3 tapered 1:1, Parallel key B6x6x2 DIN688 - splied A 2x22 DIN 482 - ø1¼" tapered1:8, Parallel key "x "x1¼" BS46 - ø1¼" splied 14T ANSI B92.1-1976 - Dust Seal - without dust seal - with dust seal - Drai Port - with drai port - without drai port - Ports - BSPP (ISO 228) - etric (ISO 262) - Desig Series - Factory specified * The permissible output torque for shafts must ot be exceeded! The hydraulic motors are magao-phosphatized as stadard. 61
Hydraulic motors with Dual shaft type RB... OPTIONS» odel- Spool valve, roll-gerotor;» Dual shaft;» Oval flage;» Side port;» Straight shafts;» BSPP ports;» Other special features. APPLICATION»»»» Coveyors; Feedig mechaism of robots ad maipulators; etal workig machies; Textile machies;» Agricultural machies;» Food idustries;» iig machiery etc. OUTLINE DIENSINS REFERENCE 8 [.31] 1 [.9] 9, [2.342] 8 [.31] P (A,B) 1 [.9] 8 [.31] "A" - SHAFT "B" - SHAFT C ø82, [3.248 ] +, +.19 4 [1.74] max ø12 [4.16] ø1 [3.937] ø82, [3.248 ] +, +.19 D 2xø13,4 max 3, [2.16] [.27] 33 [1.299] T 4 [1.74] L1 max L 2xø13,4 [.27] max 3, [2.16] C 8 -,36 [.31 ] -.14 [2.16] D 8 -,36 [.31 ] -.14 13 [.118] ø16,4 [4.189] T 4 9 [3.43] P T (A, B) Type RB RB RB RB RB RB RB RB RB 8 1 12 16 2 2 31 4 L, mm [i] L, 1 mm[i] 28, [8.19] 9, [.3] 213, 216, 22, 226, 233, 242, 23, [8.39] 14, [.] [8.] 17,4 [.69] [8.68] 21,8 [.86] [8.92] 27,8 [1.9] [9.19] 34,8 [1.37] [9.] 43, [1.71] [9.98] 4,8 [2.16] 268,[1.] 69,4 [2.73] 78 [3.71] : 2xG1/2-18 mm[.71 i] depth : G1/8-9 mm [.3 i] depth (plugged) 9 [3.43] ax 16, [4.193] 16,4 [4.189] 13 [.118] mm [i] 62
RB OTORS SPECIFICATION DATA Type Displacemet, cm³/rev [i³/rev] ax. Speed, RP ax. Torque, danm [lb-i] it.* it.* ax. Torque "A"Shaft, danm [lb-i] it.* ax. Torque "B"Shaft, danm [lb-i] ax. Output, [kw] [HP] ax. Pressure Drop, bar [PSI] ax. Oil Flow, lpm [GP] ax. Retur Pressure without Drai Lie, bar [PSI] it.* it.* it.* it.* - 1 RP 1-2 RP 2- RP RB C/C 1,[3.14] 77 97 1 [88] 13 [11] 8 [71] 9, [84] 4 [3] [44] 7 [9.] 8, [11.9] 4 [1.] [13.2] 7 [19] [73] 2 [29] RB 8 C/C 8,3[4.9] 7 94 RB 1 C/C 19, [172] 24 [212] 22 [1947] 11, [1] 12 [16] 13 [11] 11, [1] 12 [16] 13 [11] 12, [17] 1 [2.1] 6 [1.9] 7 [18.] 7 [19] [73] 2 [29] it.* - max RP 7 [19] 7 [19] RB 12 C/C 99,8[6.9] 12,7[7.67] 19,6[9.74] 199,8[12.19] 2,1[1.26] 31,7[19.26] 397 [24.4] 6 7 28 [248] 14 [124] 14 [124] 13 [11] 1 [2.1] 47 6 3 [26] 34 [31] 2 [177] 23 [23] 2 [177] 23 [23] 12, [17] 14, 6 [1.9] 7 [18.] 7 [19] [73] 2 [29] 7 [19] RB 16 C/C 37 47 3 [26] 39 [34] 2 [177] 23 [23] 2 [177] 23 [23] 1 [13.4] 12, [17] 14 [23] 17 [24] 17 [24] 17 [24] 13 [188] 6 [1.9] 7 [18.] 7 [19] [73] 2 [29] 7 [19] RB 2 C/C 3 37 3 [26] 39 [34] 2 [177] 23 [23] 2 [177] 23 [23] 8 [1.7] 1 [13.4] 11 [16] 17 [24] 2 [29] 2 [29] 2 [29] 17 [24] 14 [23] 6 [1.9] 7 [18.] 7 [19] [73] 2 [29] 7 [19] 6 [1.9] 7 [18.] 7 [19] [73] 2 [29] 7 [19] RB 2 C/C 24 3 3 [26] 38 [336] 2 [177] 23 [23] 2 [177] 23 [23] 6 [8.] 8 [1.7] 8 [116] 11 [16] 6 [1.9] 7 [18.] 7 [19] [73] 2 [29] 7 [19] RB 31 C/C 19 24 3 [26] 42 [372] 2 [177] 23 [23] 2 [177] 23 [23] [6.7] 6, [8.7] 7 [12] 1 [14] 6 [1.9] 7 [18.] 7 [19] [73] 2 [29] 7 [19] RB 4 C/C 1 19 3 [26] 43 [38] 2 [177] 23 [23] 2 [177] 23 [23] 4 [.4] 6 [8.] [8] 8 [116] 6 [1.9] 7 [18.] 7 [19] [73] 2 [29] 7 [19] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 63
RB OTORS SHAFT EXTENSIONS C - ø2 straight, Parallel key A8x7x3 DIN 688 SH - 1" splied, BS 29 (SAE 6B) ax. Torque 34 danm [31 lb-i] ax. Torque 4 danm [ 34 lb-i] 8 -,36 [.31 ] -.14 -.118 28 -,3 [1.12 ] ø2 [.984 ] -,21 -.8 6, [.26] 28-,3 [1.12 ] -.118 +,2 6,2 -, +.1 [.246-.19] 8 mi 18 [.71] deep ø28,6 [1.124] ø2,323±,3 [.997±.12] 8 mi 22 [.866] deep 43 [1.693] ø21,47±,7 [.84±.27] 26,4±1 [1.4±.4] 43 [1.7] PERISSIBLE SHAFT LOADS The load diagrams are valid for a average bearigs life of 16 hrs at 2 r.p.m. with mieral base lubricatig cotaiig atiwear additives (ref.iso 281 (3.3)stadard). The "A" curve gives the maximum static load affordable by the bearigs. The "B" curve gives the radial load top limit without axial load of 2 dan. Pr dan 1 12 1 7 47 lbs. 21 dan 47 lbs. 21 dan Prad lbs 3 2 2 1 Pr 1 2 A B Pa -4-3 -2-1 1 2 3 4 6 7 8 9 1 mm -1. -1 -.. 1 1. 2 2.. 4 i ORDER CODE RB 1 2 3 4 / Pos.1 - Displacemet code 8 1 12 16 2 2 31 4-1, cm /rev [3.14 i /rev] - 8,3 cm /rev [4.9 i /rev] - 99,8 cm /rev [6.9 i /rev] - 12,7 cm /rev [7.67 i /rev] - 19,6 cm /rev [9.74 i /rev] - 199,8 cm /rev [12.19 i /rev] - 2,1 cm /rev [1.26 i /rev] - 31,7 cm /rev [19.26 i /rev] - 397, cm /rev [24.4 i /rev] Pos.2 - "A" Shaft Extesios* C SH Pos.4 Pos. omit - ø2 straight, Parallel key A8x7x3 DIN688-1" splied, BS 29 (SAE 6B) Pos.3 - "B" Shaft Extesios* C - ø2 straight, Parallel key A8x7x3 DIN688 SH - 1" splied, BS 29 (SAE 6B) - Special Features (see page 119) - Desig Series - Factory specified NOTES: * ** For other shaft extesios please cotact with "+S Hydraulic". Color at customer's request. The hydraulic motors are magao-phosphatized as stadard. 64
HYDRAULIC OTORS PL APPLICATION» Coveyors» Feedig mechaism of robots ad maipulators» etal workig machies» Textile machies» Agricultural machies» Food idustries» iig machiery etc. CONTENTS Specificatio data... 66 Dimesios ad moutig... 67 Shaft extesios... 68 Permissible shaft loads... 69 Order code... 69 OPTIONS» odel - Spool valve, gerotor» Atifrictio coical bearig» Flage mout» Shafts - straight, splied ad tapered» etric ad BSPP ports» Other special features GENERAL ax Displacemet, ax. Speed, ax. Torque, ax. Output, ax. Pressure Drop, ax. Oil Flow, i. Speed, Pressure fluid Temperature rage, cm /rev [i /rev] [RP] danm [lb-i] kw [HP] bar [PSI] lpm [GP] [RP] O C [ F] 2 Optimal Viscosity rage, mm /s [SUS] Filtratio O 396 [24.16] 11 : [ 441] it.: 9 [222] 17, [23.] : 14 [ 23] it.: 17 [24] 7 [2] 1 ieral based- HLP(DIN 124) or H(ISO 6743/4) -4 14 [-4 284] 2 7 [ 98 347] ISO code 2/16 (i. recommeded fluid filtratio of 2 micros) Pressure drop bar [ PSI] 1 [ 14] 14 [ 23] Oil flow i drai lie Viscosity Oil flow i drai lie 2 mm /s [ SUS] lpm [ GP] 2 [ 98] 3 [ 164] 2 [98] 3 [164] 2, [.66] 1,8 [.476] 3, [.92] 2,8 [.74] p bar 3 2 2 1 1 p PSI 4 3 2 1 Pressure Losses 2 4 6 8 1 12 14 16 18 2 Q, GP 1 2 3 4 6 7 8 Q, lpm 6 11
PL SPECIFICATION DATA Type Displacemet, cm /rev [ i /rev] ax. Speed, [RP] ax. Torque danm [ lb-i] ax. Output kw [ HP] ax. Pressure Drop bar [ PSI] ax. Oil Flow lpm [ GP] ax. Ilet Pressure bar [ PSI] ax. Retur Pressure -1 RP without Drai Lie or ax. Pressure 1-3 RP 3-6 RP i Drai Lie, bar [ PSI] ax. Retur Pressure with Drai Lie bar [ PSI] ax. Startig Pressure with Uloaded Shaft, bar [ PSI] >6 RP -max. RP i. Startig Torque, danm [ lb-i] i. Speed***, [RP] Weight, kg [ lb] PL 121 11 9,4 [ 832] PL 8 49, [ 3.2] 79,2 [ 4.83] 11,9 [ 14] 19, [ 172] 14, [ 124] 22, [ 1947] 9,9 [ 13.3] 6 [ 16] 7 [ 2] [72] 2 [ 36] 1 [ 22] 1 [14] 7,7 [ 681] 1 6, 8 [ 1] 7 94 1,1 [ 1336] 9,9 [13.3] 12, [ 16.8] 12, [ 16.8] 14 [ 23] 14 [23] 17 [ 24] 17 [24] 22 [ 326] 6 [16] 7 [2] 17 [ 24] 17 [24] 2 [ 29] 2 [29] 22 [ 326] 1 [ 14] 1 [14] [72] 2 [36] 1 [22] 1 [ 14] 1 [14] 17 [ 24] 17 [24] 2 [ 29] 2 [29] 22 [ 326] 1 [14] 13 [ 11] 1 7, [ 1. 4] PL 1 6 7 PL 12 PL 16 PL 2 19,3 [ 178] 23,7 [21] 31,3 [277] 36,6 [ 324] 9,9 [13.3] 12, [16.8] 14 [23] 17 [24] 6 [16] 7 [2] 17 [24] 2 [29] 1 [14] [72] 2 [36] 1 [22] 1 [14] 17 [24] 2 [29] 1 [14] 1 7, 1 [ 1. 7] 48 6 9,9 [13.3] 12, [16.8] 14 [23] 17 [24] 6 [16] 7 [2] 17 [24] 2 [29] 1 [14] [72] 2 [36] 1 [22] 1 [14] 17 [24] 2 [29] 9 [131] 1 7, 2 [1. 9] 378 472 27, [ 239] 36, [323] 42 [3717] 11,7 [1.7] 12, [16.8] 12, [ 16. 8] 14 [23] 14 [23] 17 [24] 17 [24] 6 [16] 7 [2] 17 [24] 17 [24] 2 [29] 2 [29] 1 [14] 1 [14] [72] 2 [36] 1 [22] 1 [14] 1 [14] 17 [24] 17 [24] 2 [29] 2 [29] 8 [116] 1 7, 4 [ 16.3] 33 378 3 [ 47] 1,3 [ 13.8] 6 [16] 7 [2] [72] 2 [36] 1 [22] 7 [ 1] 1 7, 6 [ 16. 8] PL 2 PL 31 PL 4 99 [ 6.4] 123,8 [7.] 18,4 [9.66] 198 [ 12.1] 247, [1.1] 316,8 [19.3] 396 [24.16] 242 33 47 [416] 23,7 [ 297] 29,8 [2637] 37,8 [334] 4,6 [ 43] 8,3 [16] 67 [93] 9,8 [13.1] 12, [ 16. 8] 14 [23] 17 [24] 6 [16] 7 [2] 17 [24] 2 [29] 1 [14] [72] 2 [36] 1 [22] 1 [14] 17 [24] 2 [29] 6 [87] 1 7, 8 [ 17.2] 19 236 48,6 [43] 6 [496] 8 [723] 7,6 [1.2] 1, [14] 12 [13] 14 [23] 6 [16] 7 [2] 17 [24] 2 [29] 1 [14] [72] 2 [36] 1 [22] 1 [14] 17 [24] 2 [29] [73] 16,8 [ 1487] 21, [186] 28, [2478] 32,2 [ 28] 41,4 [366] 43, [38] 44, [39] 1 8, 2 [ 18] 1 189 [442] 9 [222] 8,4 [76] 6,6 [8.9] 8, [11. 4] 9 [11] 11 [166] 18 [261] 6 [16] 7 [2] 17 [24] 2 [29] 1 [14] [72] 2 [36] 1 [22] 1 [14] 17 [24] 2 [29] [73] 1 8,6 [ 18.9] * Itermittet operatio: the permissible values may occur for max. 1% of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code 2/16. A omial filtratio of 2 micro or better. 3. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 6743/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 13 mm²/s [7 SUS] at C [122 F].. Recommeded maximum system operatig temperature is 82 C [18 F]. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for 1-1 miutes. 66
PL DIENSIONS AND OUNTING DATA SH Shaft SA Shaft HB Shaft C Shaft KB Shaft CB Shaft CO Shaft 67, [2.67] 4 [2.126] 4 [2.126] 61 [2.42] 68, [2.697] Shaft Dim. See Page 68 81, [3.21] Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized - CCW 8±,1 [.31±.9] Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized - CW max L Port A 2±,1 [.787±.9] T L1 P (A,B) Port B 2±,1 [.787±.9] Type PL PL 8 PL 1 PL 12 PL 16 PL 2 PL 2 PL 31 PL 4 L max, mm [i] 14 [.71] 149 [.87] 11, [.96] 1 [6.1] 19, [ 6.28] 16 [ 6.49] 171, [6.7] 181 [7.13] 191, [7.4] L, 1 mm [i] 6,67 [.26] 1,67 [.42] 13,33 [.2] 16,67 [.66] 21,33 [.84] 26,67 [ 1.] 33,33 [1.31] 42,67 [1.68] 3,33 [2.1] ø86 [3.386] ø91 [3.8] max P T (A,B) : 2xG1/2 or 2x22x1, - 1 mm [.9 i] depth : G1/4 or 14x1, - 12 mm [.47 i] depth OUNTING Square out (4 Holes) F Oval out (4 Holes) 17 [.669] 8±,3 [.31±.118] 4 o 4xø13, [.3] ø16,4±,2 [4.19±.79] ø82,±, [3.248±.19] max 131 [.16] ø82,±, [3.248±.19] 4 [2.126] 13 [.119] [2.17] 4xø13, [.3] 17 [.669] 8±,3 [.31±.118] 12 [4.16] ø16,4±,2 [4.19±.79] 81, [3.21] [2.17] max 96 [3.78] 81, [3.21] mm [i] 67
PL SHAFT EXTENSIONS C - ø2 straight, Parallel key A8x7x3 DIN 688 ax. Torque 34 danm [31 lb-i] SA - splied B2x22 DIN 482 ax. Torque 4 danm [34 lb-i] 8 -,36 [.31 ] -.14 3±, 1.18±,2 28-,3 [1.1 ] -.118 8 mi 22 Deep [.866] ø3 [1.378] 43 [1.69] ø2-,21 [.98 ] -.8 8 mi 22 Deep [.866] ø3 [1.378] 43 [1.69] ø24 -,13 [.94 ] -.1 CO - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 ax. Torque 34 danm [31 lb-i] CB - ø32 straight, Parallel key A1x8x4 DIN 688 ax. Torque 77 danm [681 lb-i] 6,4 -, [.22-.2],±,2 [.217±.79] 1,3 +,1 [. +.39] 1 -,36 [.394 ] -.14 [1.1 ] +,1 28-,13 +.39 -. 8 mi 22 Deep [.866] ø3 [1.378] 43 [1.69] ø23,9 -,1 [.94 ] -.39 ø2,4 -,21 [.98 ] -.999 3-,2 [1.38 ] -.79 8 mi 22 Deep [.866] ø3 [1.378] [1.97] ø32 [1.26 ] +,18 +,2 +.7 +.1 SH - splied, BS 29 (SAE 6B) ax. Torque 4 danm [34 lb-i] HB - ø1¼" splied 14T, DP12/24 ANSI B92.1-1976 ax. Torque 9 danm [841 lb-i] 6,2-, [.246-.2 ] 2,7 +1 +.39 [1.1 ] 38±, [1.49±.19] ø2,3 -,1 [.996 ] -,1 -.39 -.9 -,8 ø21,6-,12 -.31 [.8 -.49 ] 8 mi 22 Deep [.866] ø3 [1.378] 1,3 [.] 43 [1.69] ø23,9 -,1 [.94 ] -.39 7 [.26] 8 mi 22 Deep [.866] ø3 [1.378] 6 [2.2] -, ø31,7 -,1 [1.2 ] -.19 -.39 KB - tapered 1:1, Woodruff key 6x9 DIN6888 ax. Torque 9 danm [841 lb-i] 6 -,3 [.236-.12] ø22-,21 [.866-.83] 1:1 A 18 [.78] S=3 Tighteig Torque 1±1 danm [88±88 lb-i] 19 -,29 [.748 ] -.114 ø3 [1.378] 2x1, ø4, [.18] ø37 [1.4] A 36 [1.417],8 [.228] 8 [2.28] mm [i] 68
PL Permissible Shaft Loads PL ad RL The curves apply to a B1 bearigs life of 2 hrs Pr lbs. Pr dan P max =3 dan [674 lbs] 7 6 4 3 A - ax. radial shaft load. -1 B - = mi -1 C - =1 mi -1 D - =2 mi -1 E - =4 mi 2 1 mm 4 3 2 1-1 -1.7 i. ORDER CODE PL 1 2 3 4 6 7 Pos.1 - outig Flage omit - Square mout, four holes F - Oval mout, four holes Pos.2 - Displacemet code* - 49, cm /rev [3.2 i /rev] 8-79,2 cm /rev [4.83 i /rev] 1-99, cm /rev [6.4 i /rev] 12-123,8 cm /rev [7. i /rev] 16-18,4 cm /rev [9.66 i /rev] 2-198, cm /rev [12.1 i /rev] 2-247, cm /rev [1.1 i /rev] 31-316,8 cm /rev [19.3 i /rev] 4-396, cm /rev [24.16 i /rev] Pos.3 C CO SH SA CB HB KB Pos.4 - Shaft Seal Versio omit U Pos. - Ports omit Pos.6 Pos.7 - Desig Series omit - Shaft Extesios* * - ø2 straight, Parallel key A8x7x3 DIN688 1 1 1 - ø1" straight, Parallel key / "x / "x1 / " BS46 4 4 4 - ø2,3 splied, BS 29 (SAE 6B) - ø24 splied, B 2x22 DIN 482 - ø32 straight, Parallel key A1x8x4 DIN688 1 - ø1 / " splied 14T ANSI B92.1-1976 4 - ø3 tapered 1:1, Woodruff key 6x9 DIN6888 - Stadad shaft seal - High pressure shaft seal - BSPP (ISO 228) - etric (ISO 262) - Special Features (see page 119) - Factory specified NOTES: * For the Fuctio Diagrams data please look at "+S Hydraulic" Catalogue for P motors, pages 19 23. ** The permissible output torque for shafts must ot be exceeded! The hydraulic motors are magao-phosphatized as stadard. 69
HYDRAULIC OTORS RL APPLICATION» Coveyors» Feedig mechaism of robots ad maipulators» etal workig machies» Textile machies» Agricultural machies» Food idustries» iig machiery etc. CONTENTS Specificatio data... 71 Dimesios ad moutig... 72 Shaft extesios... 73 Permissible shaft loads... 74 Order code... 74 OPTIONS» odel - Spool valve, roll-gerotor» Atifrictio coical bearigs» Flage mout» Shafts - straight, splied ad tapered» etric ad BSPP ports» Other special features GENERAL ax. Displacemet, cm /rev. [i /rev.] ax. Speed, [RP] ax. Torque, danm [lb-i] ax. Output, kw [HP] ax. Pressure Drop, bar [PSI] ax. Oil Flow, lpm [GP] i. Speed, [RP] Permissible Shaft Loads, Pressure fluid Temperature rage, dan [lbs] O C [ F] 2 Optimal Viscosity rage, mm /s [SUS] Filtratio O 397 [ 24.4] 97 : 61 [ 4] it.: 69 [61] 16 [21.] :17 [ 24] it.: 2 [29] 7 [2] 1 P = [1124] a ieral based- HLP(DIN 124) or H(ISO 6743/4) -4 14 [-4 284] 2 7 [ 98 347] ISO code 2/16 (i. recommeded fluid filtratio of 2 micros) Pressure drop bar [ PSI] 1 [ 14] 14 [ 23] Oil flow i drai lie Viscosity 2 mm /s [SUS] 2 [ 98] 3 [ 164] 2 [98] 3 [164] Oil flow i drai lie lpm [ GP] 2, [.66] 1,8 [.476] 3, [.92] 2,8 [.74] p bar 3 2 2 1 1 p PSI 4 3 2 1 Pressure Losses 2 4 6 8 1 12 14 16 18 2 Q, GP 1 2 3 4 6 7 8 Q, lpm 7