ABC HOBBY ORIGINAL RADIO CONTROL CAR Instruction Manual Study the instructions thoroughly before assembly. FRONT WHEEL DRIVE NEW STYLE STRUT SUSPENSION BATHTUB CHASSIS 4 BEVEL GEAR DIFFERENTIAL FULL ADJUSTABLE SUSPENSION UNIVERSAL JOINT WHEEL BASE:210mm BODY WIDTH:157mm-163mm
18T Bevel Gear 10T Bevel Gear 1 GEAR BOX Diff Outer Joint 2 x 8 mm Tapping Diff Cover 2 x 8 mm Tapping Diff Cover Diff Rubber Pad Bevel Cross Pin 5 x 0.3 mm Spacer 3.5 x 0.2 mm spacer Diff Rubber Pad 48T Diff Gear M4 O Ring Tighten the screw equally 3.5 x 0.2 mm spacer 5 x 0.3 mm Spacer M4 O-ring Bevel Cross Pin 850 Bearing 10T Bevel Gear 18T Bevel Gear M4 O Ring Make sure that the gears are in the right drive orientation. 1.6 x 0.8 mm Pin Counter Gear Shaft 3 x 4 mm 850 Bearing 20T Counter Gear 3 x 4 mm Diff Gear Box A Counter Gear Shaft Counter Gear Shaft 1.6 x 0.8 mm Pin Diff Gear Box A 48T Diff Gear 1510 Bearing 1510 Bearing 20T Counter Gear (48 Pitch) 25T Counter Gear (48 Pitch) Diff Gear Box B 2 MOTOR MOUNT Spur Gear Shaft 1.6 x 0.8 mm Pin Motor Plate Holder Spur Gear Shaft 850 Bearing Upper Mount Holder AL Motor Plate A AL Motor Plate A Flat Head Flat Head 850 Bearing 3 x 4 mm 50T/25T Spur Gear 850 Bearing 1.6 x 0.8 mm Pin Upper Mount Holder AL Motor Plate B Upper Mount Holder Upper Mount Holder 25T Counter Gear Holder Holder 2
Support 3 STEERING UNIT S m o o t h!! 50T/25T Spur Gear Crank A Support Crank B 4.8 mm Ball Stud 3 x 6 mm Plastic Spacer Crank B Crank A Gear Ratio 48 Pitch 4 mm King Pin S m o o t h!! components should be free of bind. Calculation of Gear ratio Kit Standard S m o o t h!! 25T Counter Gear 20T Counter Gear 50T/25T Spur Gear 48T Diff Gear 4 HUB CARRIER Wheel Hub 22T Pinion Gear 50T/25T Spur Gear REAR Wheel Hub Unit must move smoothly 3 x 6 mm Plastic Spacer 4 mm King Pin 3 x 12 mm 3 x 6 mm Plastic Spacer 4 mm King Pin 3 x 5 x 0.5 t Washer Ball FRONT Axle Insert a kingpin along the angle of Knuckle Hole Ball Stopper Axle Ball Stopper 3 x 5 x 0.5 t Washer Wheel Hub Ball Stud 4.8 mm Ball 3 x 8 mm 2 mm Hex Wrench Wheel Hub Universal Joint Ball must move smoothly 3 x 5 x 0.5 t Washer Universal Joint must move smoothly 3
Plastic Washer Sus Arm Pin Flat Head 5 SUSPENSION ARM Sus Arm Holder A Sus Arm Holder B Sus Arm Holder A Sus Arm Holder B Right Left Assemble the right and left arms carefully, remembering the right and left orientation. 1 mm Plastic Washer FRONT SECTION Sus Arm Pin Right Left Sus Arm Holder B Sus Arm Holder A 1 mm Plastic Washer Sus Arm Holder A Sus Arm Holder B Flat Head 1 mm Plastic Washer REAR SECTION Sus Arm Pin Sus Arm Holder B Flat Head Sus Arm Holder A 1 mm Plastic Washer 6 UPPER DECK 3 x 12 mm Back Side 3 x 12 mm Bulk Support Flat Head 3 x 12 mm Flat Head Upper Deck Bulk Unit Ball Stud 4.8 mm Bulk Support Bumper Bulk Flat Head Bulk Unit 3 x 12 mm Flat Head Flat Head 4
7 UPPER MOUNT 3 x 12 mm Upper Mount Upper Mount 2.6 mm x 8 mm Flat Head King Pin Ball King Pin Ball 4.8 mm Aluminum Ball Upper Mount 2.6 mm x 8 mm Flat Head Rod 3 x 6 mm Plastic Spacer S m o o t h!! Crank C 4.8 mm Aluminum Ball 3 x 12 mm Dumper Sleeve 1/2 Scale 8 FRICTION DUMPER Dumper Remover 3 mm Silicon O-ring Friction Dumper Piston Attach an O-ring to Ball Stud. Piston Friction Dumper Piston Friction Dumper Sleeve 3 mm Silicon O-ring After having attached Ball Stud, attach a damper piston to the upper mount from bottom. Because the materials of the upper mount are stiff, you can put it on easily when you use 7.0mmBox Driver. No.16862 Fine Fix Wrench 7.0mm Box Driver (Not included in this kit) 7.0mm Box Driver 7.0mm Box Driver Friction Dumper Piston 2.6 mm x 10 mm Capped Friction Dumper Piston Friction Dumper Sleeve Apply damper grease to a piston. 5
9 BODY MOUNT Body Mount B Body Mount C Body Mount A Body Mount B Body Mount C When you use TAMIYA body, use Body Mount B in the, in combination with extension plate and Body Mount A in the rear. Body Mount B Body Mount A Extension Plate 10 HUB CARRIER INSTALLATION 2.5mm Hex Wrench After chassis completion, adjust it again. 2.5mm Hex Wrench 6
11 UPPER MOUNT INSTALLATION Sandwich all springs between knuckle and kingpin balls. Battery Cover Tie Rod Insert the dumper piston with grease applied on each dumper sleeve. Cable Cramp Tie Rod Battery Cover Tie Rod 12 RADIO SYSTEM All electronics stuffs are not included in this kit. Battery Antenna Wire Switch Saver Spring (Silver) Saver Spring (Gold) Saver Cap Servo Horn Choose the Saver Serration much with your servo. Saver Serration 23 25 Saver Serration Servo Horn Saver Spring (Gold) X 2 Transmitter Receiver Connector Connect to Motor 2 Use the screw from your servo. Servo Speed Controller 3 mm Nut Saver Spring (Silver) Reverse Switch The position of the reverse switch varies according to a transmitter. 3 90 Degrees 3 mm Nut Set the reverse switch of the transmitter so that servo Horn moves in the direction of the arrow when you operated a steering to the right. 7 **When the power is ON, the servo horn should be in the neutral position as shown in the picture.
3 x 6 mm 13 MOTOR INSTALLATION 3 x 6 mm 3 x 6 mm Washer / Silver 22T Pinion Gear (48 Pitch) 3 x 3 Set Remove Spur Gear and bearings. 540 Size Motor Copy Paper 3 x 3 Set 3 x 6 mm 22T Pinion Gear (48 Pitch) Attach a motor with 3X6mm. Attach a counter gear, after put on a pinion gear. After then, attach gear cover with body clip. To get a perfect gear mesh, place a piece of paper between the gears and tighten the motor mount screws. Adjust motor position for smooth gear mesh. 14 STEERING LINKAGE 3 x 7 mm Washer / Black 3 x 7 mm Washer / Black Servo Holder Rod End Servo Holder Servo Holder L Crank 䎜䎓䏲 䎜䎓䏲 q 8 **When the power is ON, the servo horn should be in the neutral position as shown in the picture.
4 mm Wheel Nut 15 ELECTRONICS INSTALLATION Speed Controller Receiver Double Sided Tape Double Sided Tape Foam Insert Tire Body Mount A Foam Insert Body Clip Wheel Cable Cramp CA Cement Body Mount A Body Mount B Body Mount C Foam Bumper **Wipe an adhesion side with alcohol etc. 16 BODY INSTALLATION Knife Edge Reamer #69006 (Not included in this kit) Body Clip Body Clip Complete! Cut Cut 4 mm Wheel Nut 9
17 BASIC SETTING Toe Toe Out 1 Toe In : Movement at the steering operation becomes calm. Toe Out : Movement at the steering operation becomes quick. Forward Forward Camber Adjust the length of the steering ball of the lower knuckle, then Change a camber. Toe Out Toe In Toe Toe In 1 Toe In : Increase >> Stability improves. Decrease >> slide becomes early. Toe Out : You must not make the rear toe-out. Ride Height Attache washer for change ride-height Ride Height / Droop Ride Height : A horizontal state is a neutral characteristic. Nose Down >> Movement at the steering operation becomes quick. Tail Down >> slide becomes early. Droop : Adjust a traction in the roll. Decrease Droop >> Movement at the steering operation becomes quick. Decrease Droop >> slide becomes early. Droop Turn the 3x8mm screw, them change droop. Droop 2mm Ride Height 5mm Droop 3mm Ride Height 5mm Camber Camber : Adjust a traction in the roll. Increase Negative Camber >> Traction feeling improves. (The excessive negative loses traction, and a tire is worn.) Positive Camber >> Don`t make this setting by On-road car. Positive Camber 0 Negative Camber Negative Camber 0 Positive Camber Positive Camber 0 Negative Camber Negative Camber 0 Positive Camber 0 0 Negative 1 Negative 1 10
1 set 1 set P4 O-ring x 2 2x8mm Tapping x 4 Universal Joint Diff Outer Joint Diff gear Rubber Pad Bevel Gear Set Bevel Cross Pin P3 O-ring (Silicone) 3.5x0.2mm Spacer 3.5x0.2mm Spacer 2.0x9mm Pin 1.6x8mm Pin 4mm King Pin Axle Shaft Ball 4.8mm Ball Stud Suspension Armin Rod A/B set Spur Gear A/B set Counter Gear 48 Pitch Diff Gear Counter Gear Spur Gear Shaft Counter Gear Shaft AL Motor Plate 22T Pinion Gear 48T Diff Gear 50T/25T Spur Gear Gear Box Gear Cover 1 set 4.8mm Aluminum Ball Servo Saver Rod End Tie-Rod Upper Deck Upper Mount Upper Mount Bumper Battery Cover A/B set 1 set Bulk 1 set Bulk Support Knuckle Set L/R King pin Ball Sus Arm Holder Set Cable Cramp Suspension Sim Set Extension Plate Bulk Set Support 1 set Wheel Hub Crank C 3x6 Plastic Spacer Grid Main Chassis Friction Dumper Crank Set Grid Sus Arm Set Crank B Crank A Upper Mount Holder 1 set 1 set Unit Holder Motor Plate Holder Motor Mount Plastic Pats set Body Mount Set SB Racing Tires 8S Type Wheels Foam Bumper 1.0mmx5T Spring 3x4mm x 2 3x6mm x 2 3x8mm x 57 3x12mm x 4 3x8mm Flat Head x 17 3x12mm Flat Head x 2 2.6x10mm Capped x 4 1 set Antenna Pipe Set Wheel Nuts Body Clip Double Sided Tape Silicone Oil #5000 Dumping Grease 2.6x10mm Flat Head Phillip x 4 3x5mm 0.5t Washer x 6 3x7mm Washer x 4 3mm Nut x 1 Grid Hard Ware Set 1510 Bearing 850 Bearing 11
0.7mmx5T Spring 0.8mmx5T Spring 0.9mmx5T Spring 1.1mmx5T Spring AL Servo Horn AL Rod 50/30T Spur Gear Set Crank Holder (for CFRP Chassis) Rod End 3x10mm Set Set AL 4.8mm Ball Stud Titanium 3x25mm Turnbuckles AL Oil Filled Dumper King Pin Ball Holder (for CFRP Chassis) Antenna Holder (for CFRP Chassis) Battery Holder (for CFRP Chassis) Dumping Grease M Dumping Grease S 630 Bearing AL Hub 5mm AL Hub 6mm AL Hub 7mm (10g x 2) Extra Weights Heavy Duty Servo Saver Reinforced / Black Reinforced / White S-Mesh / White S-Mesh / Black BRE / White BRE / Black HS / White HS / Black **You will need #25762 and #24757. Carbon FRP Upper Mount **You will need #25763. **You will need #25762. Grid Carbon FRP Main Chassis **You will need #25764. Carbon FRP Upper Mount Carbon FRP Upper Deck 3x4mm x 2 1 set 3x6mm x 6 3x8mm x 56 3x12mm x 4 3x8mm Flat Head x 17 Grid Titanium Set 3x12mm Flat Head x 2 N Racing Tires 12