POWERFORMED Substations atalogue: Section Section - USLIGN Fittings For Rigid usbar USLIGN Fittings For Rigid usbar Table of ontents Sec/Page Table of ontents Sec/Page Endcaps usbar End aps (Weld-on)... - usbar End aps (Spherical)... - usbar End aps (Plug)... - usbar End ap (orona Dome)... - Earthing Earthing Stirrup Plate... -3 usbar Earthing Stirrup... -3 Palms/Flags usbar luminium Palm (Inline)... -4 usbar luminium Palm (Transverse)... -4 usbar End ap Palm... -4 usbar End Palm (apped)... -5 usbar End Palm (L-Type)... -5 -Frames Flange Type - luminium... -6 olted Type - luminium... -6 ngled Elbow Type - luminium... -6 Welded Type - luminium... -6 usbar Joint Sleeves usbar Joint Sleeve... -7 usbar olted Joint Sleeve... -7 Flexible onnectors luminium Type... -8 luminium Type... -8 luminium Type... -8 luminium Type D... -9 luminium Type E... -9 opper Type FL-... -10 opper onding Lead (Single Hole)... -11 opper onding Lead (Double Hole)... -11 Tinned Type F Series (Flat raid)... -1 Tinned Type R Series (Round raid)... -13 Supports usbar Support ssembly (Sliding Type)... -14 usbar Support ssembly (lamp Type)... -14 usbar Fixed Support (Weld-on U -Type)... -15 usbar End Palm (L-Type)... -15 luminium usbar Support lamp (S)... -16 opper usbar Support lamp (S)... -16 Tube onnector (TF opper & TF luminium)... -17 Tube onnector (TP opper)... -17 usbar Support ssembly (Double)... -18 olted onnections luminium Straight onnector usbar to usbar (Type ST)... -19 Straight onnector usbar to usbar (Type ST opper)... -19 Reducer usbar or Studs (Type RS - opper)... -0 Reducer usbars (Type RT - opper)... -0 luminium Tee onnector usbar to usbar (Type TT)... -1 Tee onnector usbar to usbar (Type TT opper)... - luminium Terminal Lug usbar to Palm (Type T)... -3 Right ngle luminium Terminal Lug usbar to Palm (Type T-L)... -3 Terminal Lug usbar To Palm (Type T opper)... -4 Tinned oper Right ngle Terminal Lug usbar to Palm (Type LS)... - Terminal Lug Stud or usbar to Palm (Type S opper)... - usbar Terminal Lug... -6 usbar Terminal Lug - Short... -6 usbar olted Inline Palm... -6 usbar olted Earth Stirrup... -6 usbar olted Terminal Palm... -7
End aps E usbar End ap (Weld-on) ast luminium End aps, designed to effectively seal the ends of usbars. usbar end caps are manufactured to suit the following standard sizes of usbars. Spherical type end caps provide maximum corona protection for extra high voltage bus systems. Please contact PLP for custom sizes. E-10-PLP 100 E-145-PLP 1 usbar Ø System E usbar End ap 10 End ap Outer Diameter PLP End ap Type PLP Welded E usbar End ap (Spherical) E-100-SPH 100 E-1-SPH 1 E-141-SPH 141 E-160-SPH 160 usbar Ø System E usbar End ap 100 usbar Outer Diameter SPH End ap Type - Spherical E usbar End ap (Plug) E-7-PLUG 7 E-68-PLUG 68 E-9-PLUG 9 E-88-PLUG 88 E-80-PLUG 80 E-113-PLUG 113 E-105-PLUG 105 E-140-PLUG 140 usbar Ø System E usbar End ap 7 usbar Inner Diameter PLUG End ap Type - Plug E usbar End ap (orona Dome) E-70-D 80 usbar Ø System E usbar End ap 70 usbar Inner Diameter D orona Dome -
Earthing ESP Earthing Stirrup Plate Palm Type Stirrup Ø ESP-S# - * S#. * POWERFORMED Substations atalogue: Section Stirrup end ngle USLIGN Fittings For Rigid usbar System ESP Earthing Stirrup Plate S# Palm Type E.g. S1, S etc... * Stirrup bend angle (0,15,30,45 or 90) Example: ESP-S5-45 ES usbar Earthing Stirrup Welded to tubular busbar. Please contact PLP for various other sizes and styles. Width Height ES-00150 00 150. System ES usbar Earthing Stirrup 00 Stirrup Width 150 Stirrup Height Stirrup Ø - 3
Palms/Flags P usbar luminium Palm (Inline) Palms can be welded to busbars or end caps and current ratings are matched to the rating of the usbars. hoose palm types from the selection below. Please contact PLP for various other sizes and styles. P-S# Palm Type S# System P usbars luminium Palm Inline S# Palm Type E.g. S1, S etc... Example: P-S5 PT usbar luminium Palm (Transverse) usbar Outer Ø Palm Type PT-080-S# 80 S# PT-100-S# 100 S# PT-1-S# 1 S# PT-141-S# 141 S# PT-160-S# 160 S# System PT usbar luminium Palm Transverse 080 usbar Outer Diameter S# Palm Type E.g. S1, S etc... Example: P-080-S5 EP usbar End ap Palm usbar Outer Ø Palm Type EP-080-S# 80 S# EP-100-S# 100 S# EP-1-S# 1 S# EP-141-S# 141 S# EP-160-S# 160 S# System EP usbar End ap Palm 080 usbar Outer Diameter S# Palm Type E.g. S1, S etc... Example: EP-080-S5-4
Palms/Flags EP usbar End Palm (apped) usbar Outer Ø Palm Type EP-080-S# 80 S# EP-100-S# 100 S# EP-1-S# 1 S# EP-141-S# 141 S# EP-160-S# 160 S# POWERFORMED Substations atalogue: Section System EP usbar End Palm apped 080 usbar Outer Diameter S# Palm Type E.g. S1, S etc... Example: EP-080-S5 USLIGN Fittings For Rigid usbar EPL usbar End Palm (L-Type) an be used as an end cap palm and/or fixed support. usbar Outer Ø Palm Type EPL-080-S# 80 S# EPL-100-S# 100 S# EPL-1-S# 1 S# EPL-141-S# 141 S# EPL-160-S# 160 S# System EPL usbar End Palm (L Type) 080 usbar Outer Diameter S# Palm Type E.g. S1, S etc... Example: EPL-080-S5-5
Frames F usbar -Frame luminium - Frames can be supplied as components for on-site welding, bolted or pre-fabricated in PLP factory. ontact PLP with height, width, flange size and tube details. Flange Type olted Type ngled Elbow Type Welded Type - 6
usbar Joint Sleeve JS usbar Joint Sleeve usbar Outer Ø usbar Inner Ø JS-100-80 100 80 JS-100-88 100 88 JS-100-9 100 9 JS-100-94 100 94 JS-1-105 1 105 JS-1-113 1 113 System JS usbar Joint Sleeve 100 usbar Outer Diameter 80 usbar Inner Diameter POWERFORMED Substations atalogue: Section Length USLIGN Fittings For Rigid usbar JS usbar olted Joint Sleeve JS-100 100 usbar Outer Ø System JS usbar oltedjoint Sleeve 100 usbar Outer Diameter - 7
luminium Flexible onnectors F luminium Flexible onnector - TYPE Type flexible connectors are designed for mounting on the side of usbars where they may be used with double roller or roller/fixed supports. ommon palms are No. S5 and S8. Note: maximum ratings are shown for various palms. Other palms can be requested for custom applications; however fittings may be de-rated to suit. urrent Rating () Laminations Nominate palm type e.g. (S5, S8, etc...) Nominate separation length and height Offset palms available Lamination Width 100 10 x 1.mm 100 S5 1500 13 x 1.mm 100 S5 000 13 x 1.mm 130 S8 00 16 x 1.mm 130 S8 Palm F luminium Flexible onnector - TYPE Type flexible connectors are designed for mounting on the top of usbars where they may be used with double roller or roller/fixed supports. ommon palms used are No. S5 and S8. Note: maximum ratings are shown for various palms. Other palms can be requested for custom applications; however fittings may be de-rated to suit. urrent Rating () Laminations Nominate palm type e.g. (S5, S8, etc...) Nominate separation length Lamination Width 100 10 x 1.mm 100 S5 1500 13 x 1.mm 100 S5 000 13 x 1.mm 130 S8 Palm F luminium Flexible onnector - TYPE Type is another style of flexible connector incorporating conductor rather than laminations and may also be used with double roller or roller/fixed supports or attachment on to disconnectors. Note: maximum ratings are shown for various palms. Other palms can be requested for custom applications; however fittings may be de-rated to suit. urrent Rating () Stranding Palm Type Hole Ø 1800 3 x 37/3.00 4 Hole 60 x 70 18 16 00 4 x 37/3.00 4 Hole 60 x 70 18 16 Palm Thickness Nominate palm type e.g. (S5, S8, etc...) Nominate separation length and height - 8
luminium Flexible onnectors POWERFORMED Substations atalogue: Section F luminium Flexible onnector - TYPE D Type D flexible connectors are similar to type but incorporating conductor rather than laminations and are designed for mounting to an end or a side palm where they may be used with double roller or roller/ fixed supports. ommonly used palms are No. 5 and 7. USLIGN Fittings For Rigid usbar Note: maximum ratings are shown for various palms. Other palms can be requested for custom applications; however fittings may be de-rated to suit. urrent rating () Stranding 600 1 x 37/3.75 1000 1 x 61/3.75 Nominate palm type e.g. (S6, S7, etc...) Nominate separation length and height F luminium Flexible onnector - TYPE E Type E flexible connectors are used at disconnector positions and in conjunction with fixed or roller supports. They are designed to be mounted under the disconnector palm. entre of busbar to upper palm surface dimension should be 130mm + thickness of disconnector palm. Note: Maximum ratings are shown for various palms. Other palms can be requested for custom applications; however fittings may be de-rated to suit. urrent Rating () Laminations Lamination Width Palm 1500 14 x 1.mm 100 S5 16 1650 16 x 1.mm 100 S5 0 000 13 x 1.mm 130 S8 16 00 16 x 1.mm 130 S8 0 00 16 x 1.mm 130 S9 0 3150 17 x 1.mm 00 S9 0 Nominate palm type e.g. (S5, S8, etc...) Nominate separation length and height Palm Thickness - 9
opper Flexible onnectors FL_ opper Flexible onnector - TYPE FL_ Designed for flexible end to end connections between rectangular busbars or connections between busbars and terminal palms. onnectors consist of a series of high conductivity copper laminates pre-formed to allow movement during expansion of the busbar system. Laminated connectors of other sizes and forms can be made to customers specifications. Fig. No. Dimensions D E W L pprox. urrent Rating (amp) D-FL4 800 1 50 50 M1 10 400 800 6 D-FL4 100 1 50 50 M1 10 400 100 9 D-FL4 1800 1 50 50 M1 10 400 1800 13 D-FL4 400 1 50 50 M1 10 400 400 17 pprox. Thickness Note: Other lengths and drilling to customer specifications are available. D W olt Size E D olt Size E - 10
opper Flexible onnectors L opper onding Lead (Single Hole) POWERFORMED Substations atalogue: Section opper bonding leads comprise of one to six tinned copper flat braids depending on the current ratings required. Single and double hole configurations come in the following standard configurations, please contact PLP for other sizes available. urrent Rating () Length Width olt Size L-100-M10 100 M10 1 L--M10 M10 4 L-450-M10 450 M10 6 L-100-M1 100 M1 1 L-M1 M1 4 L450-M1 450 M1 6 No. raids USLIGN Fittings For Rigid usbar L opper onding Lead (Double Hole) urrent Rating () Length Hole entres Width olt Size L-100-9 100 M10 1 L-- M10 4 L-450-450 M10 6 L-100-9 100 9 M10 1 L-9 9 M10 4 L450-9 450 9 M10 6 No. raids - 11
Tinned Flexible onnectors D-F Tinned Flexible onnector - Flat raid (Type F Series) Series F flexible braid connectors consist of one or more tinned copper flat braids. Specially formed tinned copper ferrules are swaged onto the ends of the braids under high pressure to form solid rectangular terminals. Short Time Rating - ased on maximum density being below 115 amps per mm. Time period basis, 3 seconds. urrent Rating Short Time urrent Rating No. of raids Thicknesses Dimensions D L olt Size D-F10 D-F30 D-F45 100 450 600 10700 16100 1 4 6 6 8 10 14 14 14 - - - M10 D-FX10 D-FX30 D-FX45 100 450 600 10700 16100 1 4 6 6 8 10 14 14 14 - - - M1 D-F10 D-F30 D-F45 100 450 600 10700 16100 1 4 6 6 8 10 54 54 54 13 13 13 M10 D-F10 D-F30 D-F45 100 450 600 10700 16100 1 4 6 6 8 10 54 54 54 13 13 13 M10 Note: mm Standard length. Other lengths and drilling to customer specifications available. Type F & FX D Type F, F D L - 1
Tinned Flexible onnectors POWERFORMED Substations atalogue: Section D-R Tinned Flexible onnector - Round raid (Type R Series) Series R flexible braid connectors consist of one or more tinned copper round braids with specially formed tinned copper ferrules swaged onto the ends of the braids under high pressure to form solid rectangular terminals. USLIGN Fittings For Rigid usbar Short Time Rating - ased on maximum density being below 115 amps per mm. Time period basis - 3 seconds. D-R0 D-R40 D-R0 D-R40 D-R0 D-R40 D-R50 D-RE70* D-RE80* D-RF60* D-RF1K* urrent Rating 00 400 00 400 00 400 500 700 800 600 1000 Short Time urrent Rating 600 100 600 100 600 100 0000 00 37000 000 50000 No. of raids 1 1 1 3 3 4 pprox. Thickness 7.0 8.5 7.0 8.5 7.0 8.5 1.0 14.0 17.0 10.5 17.0 Dimensions D L 54 5 54 54 54 83 83 15 15 13 13 13 13 13 13 13 19 19 - - 9 9 9 40 40 50 50 40 40 49 49 olt Size M10 M10 M10 * * M10 * * M16 Note: *OVERLL LENGTH For types R, R & R - standard length mm. Other lengths and drilling to customer specifications are available. For types RE and RF - required length in millimetres to be added to catalogue number e.g. D-RE70450. Type R Type R, R, RE D Type RF D D L - 13
Support - Single S usbar Support ssembly (Roller Type) PLP roller supports are designed for mounting on disconnector palms or post insulators. Standard centre heights are 130mm over mounting palm to busbar centre line - up to busbar diameter of 141mm. Please contact PLP for various other sizes and styles. usbars Outer Ø ase Size L x W x H No.5 (Holes) Hole Diameters and entres No.8 (Holes) 76 P..D. (Holes) 17 P..D. (Holes) S-080-R 80 150 x 130 x 1 14mm 18mm S-0 100 180 x 130 x 1 14mm 18mm S-0 100 180 x 130 x 1 18mm S-04 100 180 x 130 x 1 14mm S-1-R 1 00 x 130 x 1 14mm 14mm 14mm 18mm S-141-R 141 40 x 150 x 1 18mm S-160-R 160 x x 0 18mm S usbar Support ssembly (Fixed Type) vailable for the range of usbar diameters below, with hole diameters and centres listed. Please contact PLP for various other sizes and styles. To Suit usbar Ø ase Size L x W x H No.5 (Holes) Hole Diameters and entres No.8 (Holes) 76 P..D. (Holes) 17 P..D. (Holes) No.9 (Holes) S-080-F 80 150 x 130 x 1 14mm 18mm S-01 100 180 x 130 x 1 14mm 18mm S-100-F 100 180 x 130 x 1 14mm S-1-F 1 00 x 130 x 1 14mm 14mm 14mm 18mm S-141-F 141 40 x 150 x 1 18mm S-160-F 160 x x 0 18mm - 14
Support - Single FS usbar Fixed Support (Weld-On U-Type) usbar Outer Ø FS-080-# 80 # FS-100-# 100 # FS-1-# 1 # FS-141-# 141 # FS-00-# 00 # P..D POWERFORMED Substations atalogue: Section USLIGN Fittings For Rigid usbar System FS usbar Fixed Support U-Type 080 usbar Outer Diameter # P..D. (76 or 17) EPL usbar End Palm (L-Type) an be used as an end cap palm and or fixed support usbar Outer Ø Palm Type EPL-080-S# 80 S# EPL-100-S# 100 S# EPL-1-S# 1 S# EPL-140-S# 140 S# EPL-160-S# 160 S# System EPL usbar End Palm L-Type 080 usbar outer Diameter S# Palm Type E.g. S1, S etc... EPLS usbar End Palm L Type (Sliding Support) usbar Outer Ø Palm Type EPLS-080-S# 80 S# EPLS-100-S# 100 S# EPLS-1-S# 1 S# System EPLS usbar End Palm L Type Sliding Support 080 usbar outer Diameter S# Palm Type E.g. S1, S etc... - 15
Support - Single D-S luminium usbar Support lamp (Type S) usbar support clamps are cast to size in luminium lloy and fitted with stainless steel bolts. lamps may be converted from clamping to sliding type or vice versa, by simply reversing the cap. K olt Size R S lamped Sliding O.D. Tube (mm ) Dimensions K R S D-S15 1.7 1 76 M1 37 38 D-S17 15.9 3 51 M10 36 37 D-S 19.1 76 M1 41 4 D-S30.4 51 3 M10 41 46 D-S35.4 76 38 M1 46 51 D-S40 31.8 7 51 38 M10 46 51 D-S4 41.3 33 76 38 M1 56 59 D-S45 31.8 9 76 38 M1 5 54 D-S50 38.1 3 51 3 M10 57 59 D-S55 38.1 33 76 38 M1 57 59 D-S60 50.8 40 76 38 M1 70 7 D-S65 57. 43 76 38 M1 76 78 D-S70 60.3 43 76 38 M1 76 79 D-S75 63.5 54 17 51 M16 98 100 D-S80 80.0 54 17 51 M16 103 105 D-S85 76. 54 17 51 M16 103 105 D-S100 88.9 60 17 51 M16 110 111 D-S10 100.0 61 17 51 M16 110 11 K olt Size R S lamped Sliding D-S opper usbar Support lamp (Type S) O.D. Tube (mm ) Dimensions K R S D-S5 6.35 14.0 50.8.4 M10.4 6.9 D-S10 1.70 19.0 50.8 8.5 M10 31.7 33.3 D-S15 1.70 19.0 76. 8.5 M1 36.5 38.1 D-S17 15.88.0 50.8.4 M10 38.1 36.5 D-S0 19.05.0 50.8 8.5 M10 34.9 36.5 D-S 19.05.4 76. 8.5 M1 39.7 41. D-S30.40.4 50.8 8.5 M10 46.0 47.6 D-S35.40.4 76. 8.5 M1 41. 4.8 D-S40 31.75 8.5 50.8 8.5 M10 49. 50.8 D-S45 31.75 8.5 76. 8.5 M1 4.8 44.4 D-S50 38.10 31.7 50.8 8.5 M10 53.9 55.5 D-S55 38.10 31.7 76. 8.5 M1 49. 50.8 D-S60 50.80 38.0 76. 8.5 M1 68. 69.8 D-S70 63.50 44.5 17.0 31.7 M16 8.5 84.1 Note: daptor plate part no. E8045 available to suit 17mm PD insulators and above S type connectors. - 16
Rigid Support - Single POWERFORMED Substations atalogue: Section D-TF Tube onnector (Type TF opper & TF luminium) These connectors provide an inexpensive tube to flat termination. They also combine with the flexible braid connections to provide expansion joints between tubes in lines, tubes at right angles and between tube and flat terminals. onnectors can be supplied with stainless steel bolts and nuts. USLIGN Fittings For Rigid usbar E D 10mm E Without olts With olts O.D. Tube Fig. No. Dimensions D E olt Size 10 D-TF10 1.7 1 3 54-9 M10 D-TF15 D-TF15 15.9 1 3 54-9 M19 D-TF0 D-TF0 15.9 3 48 54 9 M10 D-TF D-TF 19.1 1 38 57-3 M10 D-TF30 D-TF30 19.1 35 48 57 3 M10 D-TF34 D-TF34.4 1 44 57-38 M10 D-TF35 D-TF35.4 1 44 9 60-38 M10 D-TF40 D-TF40.4 41 48 60 38 M10 D-TF45 D-TF45.4 41 54 64 9 38 M10 D-TF45 D-TF45.4 40 76 76 51 51 M10 D-TF45 D-TF45 7.0 43 54 64 9 38 M10 D-TF46 D-TF46 8.6 1 44 9 60-38 M10 D-TF47 D-TF47 8.6 44 54 64 9 38 M10 D-TF49 D-TF49 30.0 46 54 70 9 44 M10 D-TF50 D-TF50 31.8 48 54 70 9 44 M1 D-TF5 D-TF5 34.0 51 54 70 9 44 M10 D-TF53 D-TF53 35.0 51 54 70 9 44 M10 D-TF54 D-TF54 38.1 1 57 70-51 M10 D-TF55 D-TF55 38.1 54 54 76 9 51 M10 D-TF56 D-TF56 38.1 60 76 83 44 54 M1 D-TF57 D-TF57 40.0 56 55 76 9 51 M10 D-TF60 D-TF60 48.0 64 57 83 9 57 M10 D-TF65 D-TF65 50.8 67 54 89 9 64 M10 D-TF67 D-TF67 60.0 80 54 98 9 73 M10 D-TF70 D-TF70 63.5 84 54 105 9 80 M10 D-TF75 D-TF75 76. 95 54 114 9 89 M10 Note: For current rating of parts on this page, contact PLP direct. D-PT Tube onnector (Type TP opper) For the connection of tubular busbar to switchgear terminal plates with four 14mm diameter holes at 50mm centres. Two PT connectors are required per termination. Materials: High copper content alloy castings. Stainless steel bolts, washers and nuts. 50mm mm 13mm - 17
Support - Double S usbar Support ssembly (Double) Double supports are designed to be mounted on Post insulators where busbars need to be connected via flexible connectors. Standard centre heights are 130mm over mounting palm to busbar centre line up to busbar diameter of 141mm. Please contact PLP for various other sizes and styles. Double Supports are available in the following three designs; Roller/Roller Roller/Fixed Fixed/Fixed Fixed/Sliding To Suit usbar Ø Support Type ase Size L x W x H Hole Diameters and entres 76 P..D. (Holes) S-05 100 Roller-Roller 70x180x1 14 18 S-100-FF 100 Fixed-Fixed 70x180x1 18 S-100-RF 100 Roller-Fixed 70x180x1 18 S-100-RR 100 Roller-Roller 400xx1 18 S-1-RR 1 Roller-Roller 70x00x0 18 S-141-RF 141 Roller-Fixed 0x40x1 18 S-141-RR 141 Roller-Roller 0 x 40 x 1 18 S-160-RR 160 Roller-Roller 70 x 00 x 0 18 17 P..D. (Holes) - 18
olted onnections D-ST luminium usbar to usbar (Type ST) POWERFORMED Substations atalogue: Section Type ST straight connectors are cast to size in high strength aluminium alloy and fitted with stainless steel bolts and nuts. oth connector halves are identical. USLIGN Fittings For Rigid usbar L O.D. Tube Length L olt Size D-ST5 19.1 105 M10 D-ST0.4 17 M1 D-ST35 31.8 15 M1 D-ST50 38.1 15 M1 D-ST85 50.8 178 M1 D-ST86 57. 191 M1 D-ST88 60.3 191 M1 D-ST90 63.5 191 M1 D-ST95 76. 16 M1 D-ST80M 80.0 178 M1 D-ST100 88.9 16 M1 D-ST100M 101.6 184 M1 Note: Favailable to suit a wide range of busbar sizes, contact PLP for further details. D-ST Straight onnector usbar to usbar (Type ST opper) This heavy duty connector is cast to size. The minute surface projections provide a multiple point high pressure contact which gives a low resistance joint. oth connector halves are identical. onnectors are supplied with stainless steel bolts, nuts and spring washers. L O.D. Tube Fig. Dim. L olt Size D-ST5 19.1 1 70 M10 D-ST0.4 1 83 M1 D-ST0.4 17 M10 D-ST7 8.6 140 M10 D-ST35 31.8 1 10 M1 D-ST50 38.1 1 10 M1 D-ST85 50.8 159 M1 D-ST95 76. 9 M1 Note: For current rating of parts on this page, contact PLP direct. - 19
olted onnections D-RS Reducer usbar or Studs (Type RS - opper) The type RS reducer is designed for use with solid copper busbar tube and equipment studs. Materials: High copper content alloy casting. Stainless steel bolts, washers and nuts. L olt Size O.D. Tube Dimensions olt Size Tube1 Tube L D-RS1110 8.6.4 57 51 108 M10 D-RS110 30..4 57 51 108 M10 D-RS1508 38.1. 60 57 117 M10 D-RS1509 38.1.0 60 57 117 M10 D-RS1511 38.1 8.6 60 54 114 M10 D-RS151 38.1 30. 60 54 114 M10 D-RS1514 38.1 34.9 60 54 114 M10 D-RS1610 39.7.4 60 57 117 M10 D-RS1818 44.5 44.5 76 76 15 M1 D-RT Reducer usbars (Type RT - opper) The type RT is a two piece design suitable for use with tubular busbar. It is cast in high copper content alloy and fitted with stainless steel bolts, nuts and spring washers. L O.D. Tube Dimensions olt Size Tube1 Tube L D-RT15.4 19.1 44 35 79 M10 D-RT30 31.8 19.1 48 3 79 M10 D-RT3 31.8.4 57 56 114 M10 D-RT45 38.1.4 51 51 10 M1 D-RT47 38.1 30. 51 51 10 M1 D-RT60 44.5.4 54 44 98 M1 D-RT65 44.5 31.8 6 46 108 M1 D-RT75 50.8.4 54 44 98 M1 D-RT80 50.8 38.1 64 48 111 M1 D-RT90 76. 38.1 64 51 114 M1 Note: For current rating of parts on this page, contact PLP direct. - 0
olted onnections POWERFORMED Substations atalogue: Section D-TT luminium Tee onnector usbar to usbar (Type TT) Type TT tee connectors are cast to size in high strength aluminium alloy. oth connector halves are identical. Supplied with stainless steel bolts and nuts. USLIGN Fittings For Rigid usbar O.D. Tube Dimensions olt Size Run Tap L W D-TT8 8.6.4 75 111 44 M10 D-TT35 31.8 31.8 108 15 83 M1 D-TT3830 38.1 30.0 106 149 86 M1 D-TT50 38.1 38.1 111 156 90 M1 D-TT75 50.8.4 108 159 76 M1 D-TT00 50.8 50.8 17 178 10 M1 D-TT410 60.3.4 114 171 89 M1 D-TT413 60.3 31.8 114 171 10 M1 D-TT415 60.3 38.1 114 171 10 M1 D-TT88 60.3 60.3 133 187 108 M1 D-TT89 63.5 63.5 137 191 11 M1 D-TT93 76. 50.8 130 194 99 M1 D-TT95 76. 76. 175 38 114 M1 D-TT8064 80.0 63.5 184 48 114 M1 D-TT8080 80.0 80.0 175 38 114 M1 D-TT99 88.9 50.8 143 105 M1 D-TT100 88.9 60.3 146 19 108 M1 D-TT3535 88.9 88.9 197 70 146 M1 D-TT10060 100.0 60.3 01 8 17 M16 D-TT10080 100.0 80.0 0 83 143 M16 D-TT100100 100.0 100.0 305 83 143 M16 D-TT45 114.3 63.5 194 9 117 M1 D-TT11480 114.3 80.0 10 98 15 M16 D-TT4533 114.3 8.6 10 98 15 M16 Note: For current rating of parts on this page, contact PLP direct. - 1
olted onnections D-TT Tee onnector usbar to usbar (Type TT opper) This heavy duty connector is cast to size. The minute surface projections provide a multiple point high pressure contact which gives a low resistance joint. oth connector halves are identical. onnectors are supplied with stainless steel bolts and nuts. Refer to table on adjoining page for conductor ranges and dimensions. O.D. Tube Fig. Dimensions Run Tap No. L W olt Size W D-TT3 15.9 15.9 1 55 80 35 M10 D-TT5 19.1 19.1 1 57 83 38 M10 D-TT7 0.6 0.6 1 57 83 38 M10 D-TT10 19.1.4 1 68 98 44 M1 D-TT15.4 19.1 1 6 9 38 M10 D-TT17. 0.6 1 68 98 44 M1 D-TT0.4.4 1 70 103 43 M1 D-TT0.4.4 68 98 76 M10 D-TT1 8.6 8.6 1 71 107 44 M1 D-TT.4 38.1 1 87 11 44 M1 D-TT7 8.6 15.9 73 108 50 M10 D-TT8 30..4 1 75 111 44 M1 D-TT30 31.8 19.1 1 64 95 44 M10 D-TT3 31.8.4 1 75 111 44 M1 D-TT35 31.8 31.8 1 76 114 44 M1 D-TT40 31.8 44.5 10 138 86 M1 D-TT45 38.1.4 1 76 117 50 M1 D-TT45 38.1.4 76 114 9 M10 D-TT50 38.1 38.1 105 146 83 M1 D-TT50 38.1 38.1 80 117 9 M10 D-TT55 38.1 50.8 110 149 97 M1 D-TT60 44.5.4 1 80 14 50 M1 D-TT65 44.5 31.8 1 110 156 73 M1 D-TT70 44.5 44.5 110 154 89 M1 D-TT75 50.8.4 1 84 133 50 M1 D-TT78 48.4 31.8 10 151 90 M1 D-TT79 50.8 31.8 10 151 90 M1 D-TT80 50.8 38.1 108 157 90 M1 D-TT83 48.4 50.8 116 164 95 M1 D-TT84 48.4 48.4 116 164 95 M1 D-TT85 50.8 50.8 116 16 95 M1 D-TT86 54 50.8 116 168 95 M1 D-TT88 63.5 38.1 114 168 95 M1 D-TT90 76. 38.1 114 178 83 M1 D-TT95 76. 76. 3 156 16 95 M1 D-TT100 88.9 60.3 140 11 109 M1 L W W Note: For current rating of parts on this page, contact PLP direct. -
olted onnections POWERFORMED Substations atalogue: Section D-T luminium Terminal Lug usbar to Palm (Type T) For terminating tubular aluminium busbar at switchgear palms. astings are in high strength aluminium. olts and nuts are stainless steel. USLIGN Fittings For Rigid usbar E D L K olt Size O.D. Tube No. of holes in Palm Dimensions D E K L T Z D-T0.4 38 38 16 83 83 M1 16 10 3 D-T30 31.8 38 38 16 83 83 M1 16 10 3 D-T40 38.1 4 67 38 16 76 86 M1 156 11 35 D-T50 50.8 4 83 50 16 76 100 M1 165 14 4 D-T54 57. - 83 - - 80 105-168 14 44 D-T57 60.3-83 - - 83 108-171 14 46 D-T63 61.0 83 50 30 83 100 M1 17 14 46 D-T64 63.5 4 83 50 16 83 100 M1 17 14 46 D-T80 80.0 4 83 50 15 83 130 M1 17 16 57 D-T95 76. - 83 - - 83 171-17 16 55 D-T105 88.9-10 - - 83 140-184 14 61 Z D-TL Right ngle luminium Terminal Lug usbar to Palm (Type T-L) Designed for terminating tubular aluminium busbar at right angles to the contact surface. astings are in high strength aluminium. olts and nuts are stainless steel. O.D. Tube No. of holes in Palm Dimensions D E L K T D-T30L 31.8 67 38 16 83 81 156 M1 13 D-T40L 38.1 4 67 38 16 76 87 143 M1 13 D-T57L 60.3-83 - - 79 105 185-14 D-T0L 63.5 4 89 38 89 111 16 M1 14 Note: For current rating of parts on this page, contact PLP direct. E L D K olt Size T - 3
olted onnections D-T Terminal Lug usbar To Palm (Type T opper) Designed for tube to flat connections. astings are of high copper content alloy. Lugs are machined on underside. Lugs are supplied with stainless steel bolts and nuts. Note type T0 is machined on both sides of the lug. O.D. Tube No. of holes in Palm Dimensions D E L K T Z D-T 1.7 9 --- 14 3 38 64 M10 6 16 D-T3 15.9 3 --- 16 3 49 70 M10 10 16 D-T5 19.1 3 --- 16 35 5 73 M1 10 0 D-T10 19.1 1 33 9 13 35 5 94 M10 10 0 D-T0.4 1 41 38 16 44 67 11 M1 10 3 D-T0.4 5 38 --- 19 51 59 108 M1 6 16 D-T30 31.8 1 48 38 16 51 59 17 M1 10 6 D-T33 33.3 3 70 38 16 51 76 130 M1 10 30 D-T40 38.1 3 70 38 16 51 80 130 M1 11 30 D-T46 46.0 4 70 38 16 64 89 146 M1 11 37 D-T50 50.8 4 70 38 16 70 95 15 M1 11 37 Note: For current rating of parts on this page, contact PLP direct. D T Z E L K olt Size K olt Size - 4
olted onnections POWERFORMED Substations atalogue: Section D-LS Tinned oper Right ngle Terminal Lug usbar to Palm (Type LS) Designed for terminating tubular copper busbar at right angles to the contact surface. astings are in high strength copper with a tinned surface finish. olts and nuts are stainless steel. USLIGN Fittings For Rigid usbar O.D. Tube mm Dimensions E H L T K E 50mm K olt Size H T L D-LS5 19.1 79 35 44 133 10 M1 D-LS7. 79 35 44 133 10 M1 D-LS0.4 76 41 64 143 10 M1 D-LS0.4 10 57 64 171 13 M1 D-LS 30. 10 67 76 184 19 M1 D-LS 30. 10 57 64 171 13 M1 D-LS8 30. 140 75 76 35 13 M16 D-LS30 31.8 83 43 64 146 13 M1 D-LS40 38.1 10 57 60 184 13 M1 D-LS50 50.8 10 60 73 193 13 M1 D-LS54 57. 10 73 76 00 13 M1 D-LS95 76. 10 67 83 16 13 M1 D-LS018 30. 76 54 64 143 10 M10 Note: For current rating of parts on this page, contact PLP direct. D-S Terminal Lug Stud or usbar to Palm (Type S opper) For the connection of vertical tubular busbar to switchgear terminal plates. lso used on equipment studs to provide a flat contact palm. Materials: Terminal lugs are cast in high copper content alloy. olts, nuts and spring washers are stainless steel. O.D. Tube Dimensions D L M T K D M K olt Size O.D. D-S5 19.1 16 51 51 83 130 83 10 M1 D-S0.4 16 51 51 83 149 83 13 M1 D-S0.4 19 38 38 83 149 83 13 M10 D-S11 8.6 16 38 38 76 149 76 10 M1 D-S8 30. --- --- --- 76 146 76 10 M1 D-S8 30. 51 51 10 171 108 13 M1 D-S30 31.8 51 51 10 171 108 13 M1 D-S38 34.9 51 51 10 171 105 13 M1 D-S40 38.1 51 51 10 171 105 13 M1 D-S4 39.7 51 51 10 171 105 13 M1 D-S4 39.7 35 70 70 140 10 143 13 M16 D-S181 46.0 38 51 10 178 105 16 M1 D-S31 58.7 38 51 10 03 108 19 M1 D-S0 63.5 38 51 10 03 108 19 M1 T L -
olted onnections TL usbar Terminal Lug Pin Ø Palm Type TL--S#-* S# * TL-30-S#-* 30 S# * TL-40-S#-* 40 S# * TL-50-S#-* 50 S# * end ngle System TL usbar Terminal Lug 080 Pin Diameter S# Palm Type eg. S1, S, S3 * end ngle 0,15, 30, 45 or 90 TLS usbar Terminal Lug - Short Pin Ø Palm Type end ngle TLS--S#-* S# * TLS-30-S#-* 30 S# * TLS-40-S#-* 40 S# * TLS-50-S#-* 50 S# * IP usbar olted Inline Palm usbar Outer Ø Palm Type IP-050-S# 50 S# IP-080-S# 80 S# IP-100-S# 100 S# System IP usbar olted Inline Palm 50 usbar Outer Diameter S# Palm Type E.g. S1, S etc... ES usbar olted Earth Stirrup ES-050 50 ES-080 80 ES-100 100 usbar Outer Ø System ES usbar olted Earth Stirrup 50 usbar Outer Diameter - 6
olted onnections POWERFORMED Substations atalogue: Section TP usbar olted Terminal Palm usbar Outer Ø TP-050-S# 50 S# TP-080-S# 80 S# TP-100-S# 100 S# Palm Type USLIGN Fittings For Rigid usbar System TP usbar olted Terminal Palm 50 usbar Outer Diameter S# Palm Type E.g. S1, S etc... - 7
3-8