Principle of operation

POWR MSTR Power Meister A servo motor controls hydraulic pump speed and direction. enerate pressure and flow to match the operating cycle of machinery and to stop during idle times. ncredible energy savings by only operating when necessary. Also, position, speed, and pressure are controlled with great precision by using a high-speed digital processing servo controller. eatures igh power with MPa maximum pressure. esigned so pump operates only when necessary for energy savings and low noise. reat energy savings compared to conventional hydraulic systems. igh-speed processing of the servo controller makes positioning on the order of μm possible. ompact all-in-one design saves space. (select either vertical or horizontal setup) low of hydraulic fluid ifting Table ylinder Tank Principle of operation Rotating the motor forward brings hydraulic fluid to the head side of the cylinder which lifts the cylinder. Reversing the motor pushes hydraulic fluid to the rod side and pushes the cylinder down. The direction the pump rotates controls the direction of the cylinder, and the speed of rotation controls the speed. Maintain pressure Switch by control valve is not required owering System onfiguration (Standard onfiguration) Signals to operate the cylinder (position, speed, and pressure) are sent from the control equipment to the servo controller and the hydraulic unit responds according to the signals. The servo controller receives feedback from sensors and accurately controls the cylinder so the deviation from the signals is 0. A feedback system using position and pressure sensors makes it possible to accurately control position, speed, and thrust (pressure). About Power Meister qydraulic unit (UPS) wservo controller (P) eservo amp (compatible with motor mounted on item q) r cable (select from 3, 5, or 10 meters) tncoder cable (select from 3, 5, or 10 meters) yan cable (select from 3, 5, or 10 meters)...or 11kW motor (uable to computer (3 m)) t becomes offers. Note) ustomers must provide piping, wiring, hydraulic cylinder, sensors, control panel, and other equipment. (ontact us for information about cylinders and sensors.) M orward Power meister stops M Reverse Power meister -35

Specifications Operating Ambient Temperature/umidity Temperature Range of ydraulic luid (º) Recommended ydraulic luid Operating Viscosity Range egree of ontamination Safety Valve Pressure Adjustment Range Maximum Working Pressure olor of Paint UPS-00A Model No. A servo motor (0.75 to 11kW (servo amp drive)) Power supply 3-phase 200 to 2VA, 50/60z (servo amp power supply) or 11kW only : an motor power supply Single-phase 200 to 2VA 50/60z is required Piston pump ( to cm 3 /rev) 0 to +40º/20 to 90%R (non-condensation) 5 to 60º (Note7) Wear resistant hydraulic fluid SO V32 to 68 (V46 recommended) 20 to 200mm 2 /s {cst} NAS 10 or better UPS-00A : 3.5 to 32MPa UPS-0A/1A : 3.5 to MPa MPa (for hydraulic pump) (maximum operating pressure varies according to motor performance and options) lack Output kw apacity cm 3 /rev Maximum RPM min -1 (Note 1) Maximum low Rate l/min (Note 2) Pressure Rating MPa (ontinuous (Note 3)) Maximum Working Pressure MPa (Short term (Note 3)) UPS-00A-2*07 0.75 00 6.0 6.4 9.6 UPS-00A-2*10 UPS-00A-3*10 UPS-00A-2*15 UPS-00A-3*15 UPS-00A-4*15 UPS-0A Model No. UPS-0A-2*12 UPS-0A-4*12 UPS-0A-2*20 UPS-0A-4*20 UPS-1A Model No. UPS-1A-5*35 UPS-1A-7*35 UPS-1A-9*35 UPS-1A-11*35 UPS-1A-13*35 UPS-1A-16*35 UPS-1A-5*45 UPS-1A-7*45 UPS-1A-9*45 UPS-1A-11*45 UPS-1A-13*45 UPS-1A-16*45 UPS-1A-7*55 UPS-1A-9*55 UPS-1A-11*55 UPS-1A-13*55 UPS-1A-16*55 UPS-1A-9*75 UPS-1A-11*75 UPS-1A-13*75 UPS-1A-16*75 UPS-1A-13*11 UPS-1A-16*11 1.0 1.5 Output kw 1.2 Output kw 3.5 5.5 7.5 3.0 3.0 4.0 apacity cm 3 /rev 4.0 4.0 apacity cm 3 /rev 4.7 6.7 4.7 6.7 6.7 00 00 Maximum RPM min -1 (Note 1) 00 00 Maximum RPM min -1 (Note 1) 6.0 6.0 1 Maximum low Rate l/min (Note 2) 6.0 1 6.0 1 Maximum low Rate l/min (Note 2) 11.8 16.8 11.8 16.8 16.8 8.5 5.7 19.2 12.8 9.6 Pressure Rating MPa (ontinuous (Note 3)) 15.2 7.6 25.4 12.7 Pressure Rating MPa (ontinuous (Note 3)) 21.1 14.8 11.7 9.6 8.2 6.7 22.6 17.8 14.6 12.4 10.2 27.9 2 18.0 15.3 12.5 24.7 21.0 17.2 25.1 12.7 8.5 28.8 19.2 14.4 Maximum Working Pressure MPa (Short term (Note 3)) Tank Size it. (nominal) V:0.75 :0.65 :No tanks (Note 5) Tank Size it. (nominal) 22.8 11.4 V:1.9 :1.5 1 Maximum Working Pressure MPa (Short term (Note 3)) 22.2 17.5 14.3 12.2 1 26.8 21.9 18.7 15.2 27.0 23.0 18.8 25.8 Tank Size it. (nominal) No symbol: A:3.0 :6.0 ydraulic luid evel Range it. (estimate (Note 4)) V:0.3 :0.2 ydraulic luid evel Range it. (estimate (Note 4)) V:0.6 :0.3 ydraulic luid evel Range it. (estimate (Note 4)) Tank capacity:no symbol V:1.2, :0.6 Tank capacity:a V:0.6, :0.4 Tank capacity: V:2.8, :0.8 <Selection Precautions> The Power Meister is a hydraulic system that directly drives the hydraulic cylinder by accelerating, decelerating, or stopping a motor. ecause torque, separate from the motor torque needed to generate pressure, is needed to accelerate and decelerate, the maximum flow rate and maximum pressure may be lower than in the above table due to restrictions caused by the machinery's operating conditions. When you select a product, you first need to clarify the operating cycle and load of your machinery (the hydraulic cylinders that the Power Meister will drive) in advance and then consult with us. (Note 1) There is a limit to the operating pressure at maximum RPMs due to the low torque that is characteristic of this motor's output at high RPMs. (Note 2) Theoretical flow under no load. Actual flow varies according to load pressure. (Note 3) Rated pressure is rated torque of the motor, maximum operating pressure is pressure output at 150% torque. owever, if this pressure exceeds MPa, the maximum operating pressure of the hydraulic unit is below MPa. Also, the maximum RPM and operating pressure may be limited depending on the acceleration, deceleration, and load conditions. larify your machinery's operating conditions first, and contact us for more information. (Note 4) f the fluctuation in oil volume is greater than the allowed values an auxiliary tank can be connected to resolve this. ontact us for more information. (Note 5) f your selection does not include a tank, then a separate oil tank is required. We can also manufacture oil tanks, so contact us for more information if you are interested. (Note 6) The temperature of the hydraulic fluid is affected by many factors, such as the hydraulic unit's operating environment, operating methods, and load conditions. The customer must confirm the unit's actual continuous operating conditions. Also, long-term, continuous operation under pressure or high-frequency reciprocal operation may result in increased oil temperatures. Therefore, operating pressure limits or installation of a cooling system may be necessary. ontact us for more information. -36

Servo ontroller Servo Amp Model No.: P-P3-10-2-20 Power Supply/onsumption 24V ±15%/less than 10W Separate power supply for sensor is needed Operating Ambient Temperature/umidity 0 to +55;/90% R or less (no condensation) ontrolled Parameters ylinder position, speed, pressure ontrol mode automatic switching function available ommand nput nput Signals (ontact Signals) Output Signals Speed ommand Pressure ommand Position ommand Pressure Sensor nput Position Sensor nput Servo Amp / Analog voltage ±10V/maximum cylinder speed (*1), cylinder extended by positive voltage, cylinder retracted by negative voltage Analog voltage ±10V/maximum control pressure (*2), positive voltage adds pressure to head side, negative voltage adds pressure to rod side Position selection contact signal (4 contacts), target position selected by bit pattern of 4 contacts, acceleration function generated in controller moves cylinder to target position (*1) Parameter setting (*2) Trimmer setting Target position, maximum speed, and acceleration set using internal parameters Servo on, alarm reset, control mode external switching, start point search start, start point retraction end point S, start point proximity S Alarm, servo ready, control mode monitor, start point search end/in position (also output), pressure consistency Uses pressure sensor with response time of 1 ms Analog voltage 0.5 to V, or 1 to 5V (2ch) or less. 90 phase difference biphasic pulse, start point pulse (line receiver input) or analog voltage 0 to 10V (only with -A option) Output: revolve command (analog voltage ±10V), servo amp, servo alarm reset nput: Servo alarm, servo ready f using pulse output position sensor, start point search is necessary once after turning on the power Pulse output positioning sensor: Uses sensor with resolution of 1 µm or less Analog voltage output positioning sensor: Uses sensor with response time of 2 ms or less ontrol Panel 5 digits with symbol, 4 key input, selecter switch data setting/display, test run function onnector for controller, pins are attached. When you use the spacer for the servo controller (Option:ZV-8676-02A-01), the installation dimension becomes the same as the old design [P- P2-10(-A)-2-10]and the height from the mounding surface to the connector becomes almost the same. Model (UPS Series) Output kw ompatible Servo Amp Model UPS-00A-**07 0.75 PA-P1-10-R075-20 UPS-00A-**10 1.0 PA-P1-10-R100-20 UPS-00A-**15 1.5 PA-P1-10-R150-20 UPS-0A-**12 1.2 PA-P1-10-R-20 UPS-0A-**20 PA-P1-10-R200-20 UPS-1A-***35 3.5 PA-P1-10-R350-20 UPS-1A-***45 PA-P1-10-R450-20 UPS-1A-***55 5.5 PA-P1-10-R550-20 UPS-1A-***75 7.5 PA-P1-10-R750-20 UPS-1A-***11 PA-P1-10-R11-20 Remarks Regenerative resistor built in xternal regenerative resistor included Note 1) Power: 3-phase 200 to 2VA, 50/60z Note 2) Separate motor cable and encoder cable are needed to connect the servo motor on the hydraulic unit. Note 3) An auxiliary external regenerative resistor may need to be added in some operating conditions if the built-in or external regenerative resistor is not sufficient. or more details contact us with information about your operating conditions (load motion diagram). Note 4) A cable connector is included. -37

xplanation of model No. UPS-00A UPS-0A/UPS-1A UPS 00 A 2 07 1 20 UPS 1 A 9 V 75 1 S 4 S 20 esign number esign number Alarm switch options pressure adjustment range No symbol: No options 1: 0 to 7MPa {0 to 71.4kgf/cm 2 } : With temperature switch ircuit option symbols S: With float switch No symbol: No circuit options Tank capacity : With differential pressure valve (The tank capacity can be selected when using UPS-1A) Servo motor output No symbol: it. 07: 0.75kW A: 3.0it. 10: 1.0kW : 6.0it. 15: 1.5kW Shut-off valve power supply nstallation orientation (shape) 4: 24V V: Vertical installation pressure adjustment range : orizontal installation 1: 0.8 to 7MPa {8.2 to 71.4kgf/cm 2 } : No tanks ircuit option symbols Variable pump capacity No symbol: No circuit options 2: cm 3 /rev : With differential pressure valve 3: 3.0cm 3 /rev S: With shut-off valve 4: 4.0cm 3 /rev Servo motor output Mounting method 75: 7.5kW A: oot type mounting (Note: see the ydraulic unit specifications for other sizes) size nstallation orientation 00: Variable pump capacity 2, 3, 4 V: Vertical installation : orizontal installation Power Meister/integrated unit Variable pump capacity 9: cm 3 /rev (Note: see the ydraulic unit specifications for other sizes) Mounting method A: oot type mounting size 0: Variable pump capacity 2, 4 1: Variable pump capacity 5, 7, 9, 11, 13, 16 Power Meister/integrated unit able it Specification able it AQ 03 AM R 150 20 esign number onnector shape No symbol: Straight plug : -shaped plug (There is no symbol when the motor capacity is 0.75kW or 1.0kW.) Applicable motor size 075: 0.75kW, 100: 1.0kW, 150: 1.5kW : 1.2kW, 200: kw, 350: 3.5kW 450: kw, 550: 5.5kW, 750: 7.5kW, 11: 11kW Applicable motor type R: R2 series servo motor cable able length 03: 3m, 05: 5m, 10: 10m ncoder able it AQ 03 A R A 20 esign number onnector shape No symbol: Straight plug : -shaped plug (There is no symbol when the connector type is.) onnector types A : annon connector (or 1.2kW to 11 kw) : Screw connector (or 0.75kW to 1.0 kw) Applicable motor type R: R2 series servo motor ncoder cable able length 03: 3m, 05: 5m, 10: 10m an able it AQ 03 A 20 esign number able to computer it onnector shape No symbol: Straight plug : -shaped plug an able it able length 03: 3m, 05: 5m, 10: 10m AQ 03 PM 8654A able length 03: 3m able to computer -38

7 6 5 7 6 5 7 6 5 7 6 5 nstallation imension rawings UPS-00A Series ntegrated Unit UPS-00A-*****(orizontal nstallation) UPS-00A-*V****(Vertical nstallation) input port side port side 10 50 38 31 Note 4) side input pressure detection output port (Opposite side: port side pressure 10 detection output 50 port) 38 31 Note 4) side pressure detection output port (Opposite side: port side pressure detection output port) port A 64 70 211 orizontal setup input Vertical setup Note 5) orizontal side pressure setup detection output input port (Opposite side: port side pressure detection output port) Vertical setup port side port A 64 70 211 10 50 38 31 A 64 70 75 MAX. orizontal setup side Air side breather safety (nstall valve after filling) port UPS Model No. A Approximate Weight side luid level gauge 69 98 luid level gauge 69 98 98 Tank connection port (3/4) *See the illustration to the left for the shape of the motor and connector for the encoder wiring. (or 1.5kW motor output only) *See the illustration to the The external appearance of the 1.5kW motor 69 16 left for the shape of the motor and connector for the encoder wiring. (or 1.5kW motor output only) UPS-00A-* V 07 111 469 491 16kg The external appearance of the 1.5kW motor UPS-00A-* V 10 128 486 508 17kg UPS-00A-* V 15 224 582 604 20kg Note 1) imensions in (parentheses) and two-dot chain lines are for circuit options. Note 2) The air breather is included in the unit as a separate item. After filling the tank with oil, install the air breather. Note 3) nstall the unit in a mounting orientation prescribed by Model No. (: orizontal installation, V: Vertical installation) Note 4) The port side pressure detection output port can only be used when there are no "" circuit options. UPS-00A-*****(No tanks) Note 5) side pressure detection output port (Opposite side: port side pressure detection output port) port side 10 50 38 31 A 64 70 75 MAX. orizontal setup port side 98 69 16 Tank connection port (3/4) ifferential pressure valve ifferential pressure valve UPS Model No. A Approximate Weight UPS-00A-*07 111 377 14kg UPS-00A-*10 128 394 15kg UPS-00A-*15 224 490 18kg Note 1) imensions in (parentheses) and two-dot chain lines are for circuit options. Note 2) An Oil tank will be required separately. We can also produce oil tanks. ontact us for requests for oil tanks. Note 3) nstall horizontally or vertically. or vertical installation, install the servo motor facing down. Note 4) When installing the oil tank horizontally, make sure the lowest fluid level position during the cylinder operation is always mm or greater from the bottom of the unit. (See illustration on the upper right: Mounting layout for the oil tank) Note 5) The port side pressure detection output port can only be used when there are no "" circuit options. A servo motor A servo motor Vertical setup Vertical setup luid supply port luid supply port luid level gauge port luid level gauge port port side port side 4312 4312 7421356 7421356 69 98 69 98 side A port side 31 10 31 50 38 10 50 38 Note 4) side pressure detection output port (Opposite side: port side pressure detection output port) Note 4) side pressure detection output port (Opposite side: port side pressure detection output port) Tank mm or greater mm or greater The lowest tank fluid level Mounting layout for the oil tank (orizontal setup) Tank Mounting layout for the oil tank (orizontal setup) The lowest tank fluid level A 64 A 70 64 206 70 206-39

UPS-0A Series ntegrated Unit ircuit options: S (shut off valve) none UPS-0A-*****(orizontal nstallation) M10x18 anging tap port side input side 10 60 side pressure detection output port (Opposite side: port side pressure detection output port) 36 4-φ 11 port A 66 85 215 () 35 150 180 ircuit options: S (shut off valve) attached UPS-0A-*****S4(orizontal nstallation) 35 luid level gauge 206 81 125 Note 2) UPS Model No. A Approximate Weight UPS-0A-* V 12 121 513 527 567 559 kg UPS-0A-* V 20 552 566 606 598 33kg Note 1) imensions in (parentheses) and two-dot chain lines are for circuit options and alarm switch options and S. Note 2) oes not include circuit or alarm switch options or weight of hydraulic fluid. Note 3) The air breather is included in the unit as a separate item. After filling the tank with oil, install the air breather. Note 4) nstall the unit in a mounting orientation prescribed by Model No. (: orizontal installation, V: Vertical installation) (Alarm switch option: ) loat switch (1/2) UPS-0A-*V****(Vertical nstallation) 206 port 4-φ 11 81 125 M10x18 anging tap port side 180 150 35 35 luid supply port (1/2) (Alarm switch option: ) loat switch luid level gauge ifferential pressure valve 36 10 60 side side pressure detection output port (Opposite side: port side pressure detection output port) UPS-0A-*V****S4(Vertical nstallation) 215 85 66 A () M10x18 anging tap Shut off valve (ircuit option: S) input side pressure detection output port (Opposite side: port side pressure detection output port) 10 60 36 4-φ 11 port A 66 85 215 () port side side *The dimension table and Notes 1 to 4 are in common with when there is no circuit option:s (Shut off valve) 35 35 150 180 luid level gauge 247 81 (Alarm switch option: ) loat switch (1/2) 247 81 port side port 4-φ 11 M10x18 anging tap Shut off valve (ircuit option: S) 180 150 35 35 luid supply port (1/2) (Alarm switch option: ) loat switch side 10 60 36 luid level gauge side pressure detection output port (Opposite side: port side pressure detection output port) A 66 85 215 () -40

UPS-1A Series ntegrated Unit UPS-1A-******(orizontal nstallation) 34 counterbore x1 18 hole 4-φ φ (ounter bore depth 24) 270 2 115 90 M10x20 anging tap.5 luid supply port port (1/2) Servo motor hanging bolt (o not use for hanging the unit) 90 port side M10x20 anging tap (1/2) side 45 45 (Alarm switch option: ) UPS-1A-**V****(Vertical nstallation) Shut off valve (ircuit option: S) loat switch Oil drain port port loat switch (1/2) port side Shut off valve (ircuit option: S) MAX.150 142(182) MAX.150 45 45 (Alarm switch option: ) M10x20 anging tap (1/2) side luid drain port 90 110 onnector for fan motor wiring Air intake Notes 4.) 50 or greater 135 A 4 () an motor xhaust xhaust MAX.150 142(182) MAX.150.5 90 4-φ φ 34 counterbore x1 18 hole (ounter bore depth 24) 115 2 270 luid supply port M10x20 anging tap Servo motor hanging bolt (o not use for hanging the unit) 110 135 4 A () The external appearance of a 11kW motor *or 11kW motor output only, the fan motor is provided. UPS Model No. A UPS-1A-** V 35****-A Note 2) Approximate Weight 608 627 654 645 60kg UPS-1A-** V 35**** 159 195 254 683 702 729 720 61kg UPS-1A-** V 35****- 275 763 782 809 800 63kg UPS-1A-** V 45****-A 625 644 671 662 64kg UPS-1A-** V 45**** 176 195 254 700 719 746 737 65kg UPS-1A-** V 45****- 275 780 799 826 817 67kg UPS-1A-** V 55****-A 677 696 723 714 70kg UPS-1A-** V 55**** 228 195 276 752 771 798 789 71kg UPS-1A-** V 55****- 275 832 851 878 869 73kg UPS-1A-** V 75****-A 722 741 768 759 78kg UPS-1A-** V 75**** 273 195 276 797 816 843 834 79kg UPS-1A-** V 75****- 275 877 896 923 914 81kg UPS-1A-** V 11****-A 844 863 890 881 85kg UPS-1A-** V 11**** 395 195 276 919 938 965 956 86kg UPS-1A-** V 11****- 275 999 1018 1045 1036 88kg Note 1) imensions in (parentheses) and two-dot chain lines are for circuit options and S and alarm switch options and S. Note 2) oes not include circuit or alarm switch options or weight of hydraulic fluid. Note 3) The air breather is included in the unit as a separate item. After filling the tank with oil, install the air breather. Note 4) or 11kW motor output only, the fan motor is provided. When installing the unit, provide space of 50mm or greater for air intake of the fan motor. Note 5) nstall the unit in a mounting orientation prescribed by Model No. (: orizontal installation, V: Vertical installation) -41

MO M.No. NA-UOS OR P. MA N APAN ydraulic circuit diagram (UPS-00A) ydraulic circuit diagram (UPS-0A, 1A) A A Safety valve Shut off valve (ircuit option: S) Safety valve n/out valve Safety valve idirectional rotary pump A servo motor Vacuum heck Valves When maintaining the position of the cylinder during servo off is required (for example when preventing the cylinder from self-weight falling), additional circuits (for example shut-off valve) will be required. ontact us for more information. (Alarm switch option: ) loat switch * n/out valve idirectional rotary pump A servo motor Vacuum heck Valves * Servo ontroller P-P3-10-2-20 No. MO ST SRVO ONTROR P-P3-10-2-20 *** *.* * VR3 VR1 VR4 VR2 NA NA 190 182 4 N2 T2 N3 RUN TX N 5 1 RX SW1 N4 N1 T1 55 N 2-φ 172 9 N2 T2 110 N N N4 N1 T1 80 Wiring space Approximate Weight: 0.5kg Servo Amp 0.75kW 1.0kW 1.2kW 1.5kW kw 235 50 (70) 1 Approximate Weight: 1.0kg 3.5kW kw 5.5kW 85 (70) 1 Approximate Weight: 1.7kg 7.5kW 11kW 100 (70) 220 Approximate Weight: 5.0kg Regenerative resistor 340 235 250 (70) 220 220 (70) 220 57 Approximate Weight: 5.3kg Approximate Weight: 9.6kg Approximate Weight: 3.0kg -42

Performance haracteristics Pressure ommand Voltage - Pressure haracteristics (0 to 100%) Speed ommand Voltage - Speed haracteristics (0 to 100%) (MPa) 1500 (min -1 ) Pressure 15.0 Oil motor speed 750 ommand voltage ommand 10V for MPa 0V 10V 0V command 1 (V) rom low pressure 0.15MPa To high pressure MPa ommand voltage 1 (V) ommand 10V to 1500min -1 rom low speed 50min -1 0V 10V 0V command To high-speed 1500min -1 (f oil motor is running as actuator) Pressure Sine Wave Response (MPa) Shape of command wave Shape of response wave Speed Sine Wave Response 1500 (min -1 ) Shape of command wave Shape of response wave Pressure 15.0 Oil motor speed 750 Time (s) ommand 1z sine wave, amplitude 10 to 90% welling Pressure - Power onsumption haracteristics ydraulic unit (UPS) 4.0cm 3 /rev, kw Power consumption [kw] 1.6 1.4 1.2 1 0.8 Power consumption at full cut off (Unipump 2.2kW) 1.4kW nergy savings 0.9kW (Approximately 65%) At 21 MPa dwelling pressure Time (s) ommand 1z sine wave, amplitude 10 to 90% (f oil motor is running as actuator) 0.6 0.5kW 0.4 Power consumption ontrol equipment: Unipump 2.2kW (variable piston pump) 0.2 (power meister) ull cut off power consumption (N=1800min -1 ) 0 (Note) haracteristics vary depending on operating conditions. 0 5 10 15 20 25 welling pressure[mpa] -43