TP02C 1:10 Scale Radio Controlled Electric Powered 2WD Racing Buggy Dimensions Length 410mm Width 250mm Height 150mm
Transmitter Preparation Power Switch Antenna 27MHzTransmitter Crystal T 27MHz ON Extend the antenna to the maximum Length for best performance Transmitter crystal(t) Receiver crystal(r) OFF The crystal can be replaced to change frequencies. Note : You must also change receiver crystals! Do not use AM crystals Battery Level Indicator Good Batteries Low Batteries(Light Blinks) Left turn Straight (neutral) Right turn 1 Steering Trim 3 1 Reverse Switch Servo Factory Settings DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM 2 To be used for trimming the steering operation 4 Brake 2 Throttle Trim / DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM Stop(Neutral) Forward To be used for throttle operation Throttle Trigger To be used for trimming the throttle operation 4 3ch Switch 3 Steering Dual Rate This switch is used for optional parts. To be used to adjust steering servo throw Transmitter Battery Installation Open battery cover at the bottom of transmitter. Install batteries. Follow the direction of batteries designated in the inside of battery box. Battery Cover 8 AA Alkaling Batteries AA
Transmitter Preparation A new Ni-MH battery must be charged before it is used.refer to the charger instruction manual for charging. Set up the radio control system as indicated below. Battery 3 Motor Electronic Speed Controller 2 DIGITAL PROPORTIONAL 11 5 8 7 9 RADIO CONTROL SYSTEM 6 10 ON OFF 8 5 Transmitter Servo 4 Switch 1 6 10 ON OFF Receiver Start Finish 1 Install batteries.(transmitter) 2 Extend the antenna.(transmitter) 3 Connect the battery 4 Extend the antenna.(reveiver) 5 Center the trims. 6 Switch on.(transmitter) 7 Switch on.(reveiver) 8 Make sure the servos are in command. 9 Switch off.(reveiver) 10 Switch off.(transmitter) 11 Retract the antenna(transmitter) 1 () 2 () 3 4 ) 5 6 () 7 ) 8 9 ) 10 () 11 () Tools required Needie Nose Pllers Awl Grease Screw Cement H162 Instant Glue Differential Grease Molybdenum Grease(Black) H154 Body Reamer Wire Cutters H096 ROUND CUTTER Hex Wrench Hex Wrench No need to pre-drill precise holes (1mm to 15mm)can be drilled 1mm-15mm Sharp Hobby knife For trimming bodies!
1 Front Suspension T02014 T02016 T02037 T02056 T02056 2.3 E-ring 4 T02056 T02056 3x34.5 Hinge pin front inner 2 T02016 2 Front Suspension T02092 T02015 T02008 T02083 M3x15 Screw 4 T02092 Ball stud-long 2 T02026 T02083(M3x15) Assemble both Left and Right 1
3 Buffer T02080 T02080 T02043 T02023 T02043 T02061 T02043 T02023 T02043 T02023 T02043 4.0 E-ring 1 T02080 3x6x2.5 Ball Bearing 4 T02080 4.0mm T02043 T02061 Ball stud-silvery 1 T02080 4 Buffer T02044 T02044 4.5x5.4 Block Carrier 2 T02044 M3x10 Screw 2 T02024 Ball stud-short 2 T02044 3x7x0.8 Washer 2 T02044 T02044(M3x10) 2
5 Front Suspension T02082(3x10) T02019 T02082 M3x10 Screw 2 6 Front Suspension T02011 T02042 T02042 T02012 T02054 T02100 T02034 T02054 T02054 T02100 5x10x4 ball bearing T02042 2x9.8 Shaft 4 2 T02054 2.3 E-ring 8 T02054 T02042 4.0 E-ring T02054 3x27.5 Hinge pin front outer Ball stud - short 2 4 4 Assemble both Left and Right 3
7 Front Suspension T02029 1:1 x1 Projection.Note direction approx.38mm Front Upper(Right) T02091 T02029 T02029 4.8mm Ball End(Long) T02091 3x54 Turnbuckle 8 1:1 x1 1:1 x2 4 Projection.Note direction approx.38mm Projection.Note direction approx.34mm Front Upper (Left) Steering Tip 8 Front Suspension T02092 T02092 9 Front Suspension T02063 T02082(M3x22) T02082(M3x10) T02020 T02082 M3x22 Screw 2 T02082 M3x10 Screw 4 T02063 5mm Ball stud 2 Ture-to -scale diagram Assemble as many times as specified 1:1 x2 4
10 Differential T02050(2.6x6x3) T02099(10x15x4) T02046 T02049(17x23x1) T02007(2.5x25) T02098(5x8x2.5) T02046 T02048(2.37) T02004 T02049(17x23x1) T02099(10x15x4) T02047 T02007 T02007 M2.5 T02098(5x8x2.5) T02049 17x23x1 Washer T02099 10x15x4 ball bearing T02098 5x8x2.5 ball bearing 2 2 2 T02048 2.37mm Ball 12 T02007 M2.5 Nylon Nut 1 T02007 M2.5x25 Screw 1 11 Transmission T02100(5x10x4) T02207 T02052 T02082(M3x12) T02100(5x10x4) T02051 T02003 T02082 M3x12 Screw 1 T02041 T02100 5x10x4 T02051 5x16.8 Idler gear shaft 1 T02041 5x8 Top shaft spacer 1 T02207 T02100 5x10x4 Contain oil ball bearing 6 Apply grease 5
12 Rear Chassis T02082(M3x12) T02203 T02082 M3x12 Screw 4 13 Motor Mount T02082(M3x10) T02224 T02208 T02213(M3x27) Screw Cement T02082 M3x10 Screw 1 T02082 M3x27 Screw 3 Screw Cement Apply threadlocker(screw cement) 6
Screw 14 Spur Gear T02084 M4 Flanged Nylon Nut 1 T02039 18 T02211 5x7 Top shaft spacer 1 T02211 T02039 T02040 T02038 T02001 T02038 T02084 15 Motor Motor T02053 M3x3 Screw 1 T02083 M3x8 Screw 2 T02081 3x7x0.8 Washer 2 T02081(3x7x0.8) T02083(M3x8) T02053 M3x3 T02053 Tighten the screws with one sheet of paper inserted between both gears. Screw Cement 16 Rear Suspension T02092 T02092 Ball stud-long 2 T02204 T02083 M3x8 Screw 2 T02213 M3x14 Screw 2 T02213(M3x14) T02083(M3x8) T02055 3x48 Hinge pin Rear inner 2 T02055 T02017 Cement Apply threadlocker(screw cement) Assemble both Left and Right 7 Must be purchased separately
17 Rear Shock Tower T02082(M3x22) T02063 T02025 T02082 M3x10 Screw 2 T02205 T02082 M3x12 Screw 2 T02082(M3x12) T02063 T02082 M3x22 Screw 2 T02082(M3x10) T02082(M3x12) T02082(M3x10) T02082(M3x22) 18 Rear Suspension T02082(M3x10) T02082 M3x10 Screw 6 T02082(M3x10) 19 Rear Suspension <Right> T02058 T02100 T02013 <Left> T02100 T02034 Ball stud-short 2 T02034 2x9.8 Shaft 2 T02100 5x10x4 ball bearing 4 T02034 Assemble both Left and Right 8
20 Rear Suspension T02013 T02057 T02013 3.1x6x1 Plastic Washer 2 T02057 3x30.5 Hinge pin Rear outer 2 T02057 2.3 E-ring 4 T02057 T02057 21 Rear Suspension Projection.Note direction T02029 4.8mm Ball End(Long) 4 T02091 3x54 Turnbuckle T02029 approx.35mm T02091 T02029 Right Upper 1:1 x2 2 22 Rear Suspension T02092 T02092 Assemble both Left and Right Ture-to -scale diagram 1:1 x2 9 Assemble as many times as specified
23 Shock Absorber T02064/T02065 2.3 E-ring 8 T02096 Shock Piston 4 T02097 2.8x1.9 O-ring 8 Put a little oil T02064 Front-Short x2 T02094 T02097 T02097(2.8x1.9) T02097(3.1x1) T02097(2.8x1.9) T02094 Rear-Short Put a little oil T02065 T02096 x2 T02095 T02097 T02097(2.8x1.9) T02097(3.1x1) T02097(2.8x1.9) T02095 T02097 3.1x1 Plastic Washer 4 T02096 T02094(Short) T02065 T02095(Long) T02094/T02095 8x1 O-ring T02064 4 T02064(Short) T02065(Long) T02031 5.8 Ball End 4 T02062 T02062 T02062 5.8x6 Ball stud 4 T02031 T02031 24 Shock Absorber Silicone Oil-200# for Front(Short) for Rear(Long) F R x2 T02073 T02031 T02094/T02095 F R x2 Front-Short x2 Rear-Long x2 F R Assemble both front and rear x2 Assemble as many times as specified 10
25 Shock Absorber Front-Short x2 T02094/T02095 for adjusting the spring tension Compress the spring and install x4 T02031 T02071(Short) T02094/T02095 12x1 O-ring 4 T02031 T02072(Long) Rear-Short x2 26 Front Suspension T02084(M3) T02082(M3x15) T02084 M3 Nylon Nut 2 T02082 M3x15 Screw 2 x2 Assemble as many times as specified Assemble both Left and Right 11
27 Rear Suspension T02084(M3) T02084 M3 Nylon Nut 2 T02082 M3x15 Screw 2 T02082(M3x15) 28 Front Suspension T02082(M3x10) T02202 T02082(M3x10) T02082 M3x10 Screw 6 Assemble both Left and Right 12
29 Rear Suspension T02083 M3x10 Screw 5 T02083 M3x12 Screw 2 T02083(M3x10) T02083(M3x12) T02083(M3x10) T02083(M3x10) T02083(M3x10) 30 Battery Mount / Body Mount T02083 M3x8 Screw 4 T02083 M3x10 T02108 T02083 M3x10 Screw 2 T02212 T02083(M3x8) T02083(M3x8) T02083(M3x8) T02083(M3x8) 13
31 Steering Servo Select for your servo T02030 T02081 Steering Servo-H(24T) Steering Servo-S(23T) T02061 Sanwa servo SANWA T02028 T02035 T02082(2.6x8) T02027 Steering Servo-F(25T) T02030 4.8 Ball End(Short) 2 T02081 3x7x0.8 Washer 4 T02082 T02061 Ball stud - silvery 1 T02028 T02035 1.5 Servo spacer 2 T02030 M3x10 Screw 1 T02082 M3x8 Screw 4 T02082 M2.6x8 Screw 1 32 Steering Servo T02083 M3x8 Screw 2 T02083(M3x8) Must be purchased separately 14
33 Receiver / ESC T02087 ESC T02087 Receiver T02213 Double-sided Tape T02213 M3x3 Screw 1 34 Battery T02086 T02210 If using loose battery cells, Please put the battery panel conversely. Battery T02086 Small clip 4 Must be purchased separately 15
35 Wing T02086 Small clip 2 T02086 T02220 36 Tyre Front x2 T02075 Rear x2 T02074 T02032 T02075(Sponge) T02074(Sponge) Glue T02033 Glue After fitting wheels to tyres, apply instant glue as shown. x2 Assemble as many times as specified Must be purchased separately 16
37 Tyre T02084 M4 Flanged Nylon Nut 4 T02084 38 Body 5mm 6mm 5mm T02225 Assemble both Left and Right 17
39 Body Mask the windows from the inside. Paint the body shell from the inside using spray colors. 40 Body T02086 x3 T02201 T02086 Small clip 3 x3 Assemble as many times as specified 18
T02023 T02080 T02044 T02020 T02044 Exploded View ഴ T02024 T02082 T02080 T02043 T02081 T02082 T02082 T02030 T02027 T02061 T02061 T02023 T02082 T02082 T02213 T02087 T02028 T02029 T02087 T02083 T02042 T02100 T02086 T02210 T02083 T02213 T02086 T02213 T02213 T02200 T02082 T02100 T02003 T02082 T02100 T02041 T02211 T02207 T02082 T02055 T02031 T02074 T02224 T02100 T02034 T02013 T02062 T02072 T02095 T02097 T02047 T02007 T02099 T02051 T02207 T02052 T02046 T02048 T02004 T02049 T02098 T02046 T02029 T02058 T02065 T02095 T02082 T02096 T02084 T02057 T02091 T02029 T02034 T02073 T02084 T02032 T02095 T02031 T02063 T02057 T02017 T02055 T02083 T02202 T02099 T02007 T02050 T02083 T02212 T02108 T02034 T02012 T02100 T02054 T02011 T02094 T02071 T02031 T02075 T02097 T02054 T02056 T02091 T02019 T02092 T02029 T02063 T02094 T02054 T02014 T02031 T02073 T02096 T02084 T02056 T02016 T02056 T02015 T02063 T02043 T02080 T02082 T02084 T02037 T02056 T02008 T02026 T02083 T02064 T02094 T02062 T02082 T02084 T02082 T02092 T02083 T02208 T02081 T02083 T02033 T02025 T02082 T02205 T02206 T02204 T02203 T02084 T02084 T02040 T02001 T02038 T02039 T02213 T02039 T02083 T02083 T02053 19
T02202 Parts list for TP02C off-road buggy - 1 T02203 T02204 T02205 T02206 Rear shock tower Main Chassis plate Rear chassis plate Rear arm mount-r Rear brace mount T02207 T02208 T02210 T02211 T02212 Motor plate Battery column 4pcs Differential-L Differential-R Battery plate 5x7 Top shaft spacer T02213 M3x27 Screw 8pcs T02220 T02224 T02225 3pcs M3x3 Screw 8pcs M3x14 Screw 8pcs Wing-Lexan Motor Mount Column Body-Lexan T02001 T02003 T02004 T02007 T02008 M2.5x25 Screw M2.5 Nylon Nut 80T Spur Gear 28T Spur Gear 52T Gear Differential Nut Mount Front chassis plate T02011 T02012 T02013 T02014 T02015 Steering block-l 3.1x6x1 Plastic Washer 4pcs Front alight suspension arm mount Rear arm mount-f C-type holder L C-type holder R Steering block-r Rear hub carriers-lrear hub carriers-r Rear arm mount-r Front upper suspension arm mount T02016 T02017 T02019 T02020 T02023 Servo saver upper Servo saver lower Front lower arms Rear lower arms Front brace mount 2pcs 2pcs Front shock tower Servo saver - L T02024 T02025 T02026 T02027 T02028 Rear body mount 2pcs Steering Rack Wing bracket 2pcs Wing angie shim 2pcs Battery column 2pcs Front bumper Motor guard Steering Steering Servo Steering Servo horn-f horn-h Servo horn-s Servo plate 2pcs
Parts list for TP02C off-road buggy - 2 T02029 T02030 T02031 T02032 T02033 Upper cover nylon cap 2pcs 4.8 Ball End - Long 6pcs 4.8 Ball End - Short 2pcs 3x10 Screw Spring Mount 2pcs 5.8 Ball End 2pcs Front rim 2pcs Rear rim 2pcs T02034 T02035 T02037 T02038 T02039 Hexagonal 4pcs 2x9.8 Pin 4pcs Front hinge pin barce 1.0 Servo spacer 1.5 Servo spacer 2pcs 2pcs Slipper pad 2pcs Slipper hub 2pcs T02040 T02041 T02042 T02043 Slipper Spring Top shaft spacer 4.0 E-ring 2pcs 2x9.8 Pin 2pcs Front wheel axle 2pcs Buffer Nut 4.0 E-ring Buffer column-a Buffer Spring Buffer column-b T02044 T02091 T02046 T02047 3x10 Screw 2pcs Block Carrier 2pcs 3x7x0.8 Washer 2pcs 3x54 Adjust Rod Differential Spring Differential connecting hub - Short Differential connecting hub - Long 2pcs T02048 T02049 T02050 T02051 T02052 2.37mm Ball 12pcs 17x23x1 Washer 2pcs 2.6x6x3 Stop push ball bearing idler gear shaft Gear 20T T02053 T02054 T02055 2.3 E-ring 4pcs T02056 2.3 E-ring 4pcs T02057 2.3 E-ring 4pcs Pinion Gear 21T T02058 3x3 Screw 3x27.5 Hinge pin front outer 3x48 Hinge pin Rear inner 3x34.5 Hinge pin front inner 3x30.5 Hinge pin Rear outer 2pcs 2pcs 2pcs 2pcs T02092 T02061 T02062 Ball stud sponge 2pcs Ball stud sponge 5pcs Rear CVD 2pcs Ball stud-long 2pcs Ball stud-short 5pcs Ball stud-silvery 2pcs 5.8x6 Ball stud 4pcs
Parts list for TP02C off-road buggy - 3 T02063 T02064 T02065 T02094 3x42.5 Front Shock Absorber Shaft 2pcs 3x51 Rear Shock Absorber Shaft 2pcs 12x1 O-ring 2pcs 8x1 O-ring 2pcs Shock Absorber top cover 2pcs 5mm Ball stud 4pcs 2.3 E-ring 4pcs 2.3 E-ring 4pcs Front damper case 2pcs Spring adjuster 2pcs Shock Absorber below cover 2pcs T02095 T02096 T02097 T02071 12x1 O-ring 2pcs 8x1 O-ring 2pcs Rear damper case 2pcs Spring adjuster 2pcs Shock Absorber top cover 2pcs Shock Absorber below cover 2pcs Shock piston 4pcs 3.1x1mm Washer 4pcs 2.8x1.9 O-ring 8pcs 3.5 Press washer 4pcs Front Shock Absorber Spring 2pcs T02072 T02073 T02074 T02075 T02098 Rear Shock Absorber Spring 2pcs Diaphragm 4pcs Rear-tyre 2pcs Rear-Sponge 2pcs Front-tyre 2pcs Front-Sponge 2pcs 5x8x2.5 Ball Bearing 6pcs T02099 T02100 T02080 T02081 T02084 10x15x4 Ball Bearing 5x10x4 Ball Bearing 3x6x2.5 Ball Bearing 6pcs 6pcs 4pcs T02082 3x7x0.8 Washer 10pcs T02083 M4 Flanged Nylon Nut 6pcs M3 Nylon Nut 6pcs 2.6x8 Screw 8pcs 3x5 Screw 8pcs 3x8 Screw 8pcs 3x10 Screw 8pcs 3x12 Screw 8pcs 3x15 Screw 8pcs 3x22 Screw 8pcs 3x25 Screw 8pcs 3x8 Screw 8pcs 3x10 Screw 8pcs 3x15 Screw 8pcs 3x8 Screw 8pcs T02101 T02102 T02085 2.3 E-ring 8pcs 4.0 E-ring 8pcs T02086 Front Shock Absorber 2 Set Rear Shock Absorber 2 Set Small clip 8pcs
T02087 Parts list for TP02C off-road buggy-4 Tu0219 OP Tu0222 OP Double-sided tape Antenna pipe set cover Antenna pipe set C-Type-Holder 25 Degree - L C-Type-Holder 25 Degree - R Front arm mount M3x3 1Set Tu0220 OP Tu0224 OP Tu0225 OP C-Type-Holder 30 Degree - L C-Type-Holder 30 Degree - R Servo mount 2pcs M2x5 Screw 4pcs 5.1x8x0.2 Washer 4pcs Hex mount 4pcs Tu0226 OP Tu0230 OP Tu0231 OP Front hinge pin brace Hard Shock Absorber Spring Set(Blue) Medium Shock Absorber Spring Set(Red) Tu0232 OP Tu0233 OP Buggy CVD for ae rim 2pcs Soft Shock Absorber Spring Set(Purple) 1.6x11 Spring Pin 2pcs Aluminum Washer 2pcs 5.1x8x0.2 Washer 4pcs Tu0236 Tu0237 Tu0238 Tu0240 OP OP OP OP Rear hub carriers 2pcs Rear Hub 1 Degree-L Rear Hub 1 Degree-R Ceramic Ball 2.37mm 12pcs Carbon Front Shock Tower - Buggy H475 OP H476 OP H477 OP H478 OP H479 OP 3x3 Screw 3x3 Screw 3x3 Screw 3x3 Screw 3x3 Screw Aluminium Motor Gear-15T Aluminium Motor Gear-16T Aluminium Motor Gear-17T Aluminium Motor Gear-18T Aluminium Motor Gear-19T H480 OP H482 OP 3x3 Screw 3x3 Screw Aluminium Motor Gear-20T Aluminium Motor Gear-22T
TP02C SETUP SHEET for the TeamC TP02C Driver Track / City Event Date / / Conditions Smooth Bumpy Low traction Med traction High traction Sandy Soft dirt Grass Hard soil Clay Front Suspension Shock Mounting&Camber link Front Shocks 1 2 3 Spring(color) Caster Black # Washers Camber 25 30 1 2 Wet Dry Dusty Other mm 1 2 Toe-in (+)/Out (-) Bump Steep Spacer mm mm Oil Piston # wt 1 2 # Washers mm Ride height 1 2 Rear Suspension 1 2 3 1 2 Shock Mounting&Camber link Wheelbase Long Medium Short 3 Camber Normal 1 2 4 Aluminum(Opt) # Washers mm Rear Shocks mm mm Spring(color) Black Oil Piston # wt 1 2 1 2 1 2 3 Ride height Front Tires&Wheels Rear Tires&Wheels Front Tires Rear Tires Inserts Wheels Inserts Wheels Batteries Motor Other Servo Esc Batteries Motor Pinion/Spur / Wing Wing Angle 4 10 Comments Notes