SUNCO IMPLEMENT STABILIZER OPERATOR S MANUAL WITH INSTALLATION INSTRUCTIONS

SUNCO IMPLEMENT STABILIZER OPERATOR S MANUAL WITH INSTALLATION INSTRUCTIONS

To determine what you need for mounting the stabilizer to a toolbar several things need to be considered. 1. Will the Stabilizer be operating behind the row units? i.e. cultivators. a. How far does the row unit extend behind the toolbar - to determine the length of the mount arms b. Dimensions of the toolbar i.e. 7 x 7, 5 x 7, etc. - to determine which bolt package c. Row width - to determine the length of the cross tube 2. Will the Stabilizer be operating between the row units? i.e. planters and bedders. a. Can the Stabilizer be bolted directly to the toolbar? Dimensions of the toolbar i.e. 7 x 7, 5 x 7, etc. - order proper U-bolts b. Does something interfere with bolting directly to the toolbar? i.e. driveshaft on some planters - order planter mount arm (includes hardware) 3. How many Stabilizers are required for the implement? Rule of thumb - 1 Stabilizer per 15 to 20 of toolbar length There are exceptions to this rule. Heavy implements such as potato planters may require 1 Stabilizer per 2 rows. Also bedders operating in very firm soil may require 1 Stabilizer per 10 to 12 of toolbar length. Soil type and terrain also must be considered - light soils - steeper slopes - require more stabilization MOUNTING STABILIZER BEHIND ROW UNITS High Toolbar Mount Arms Cross Tube Low Toolbar *** NOTE: Mount Arms and Cross Tube can be mounted different ways to adjust for toolbar height. 1-1

MOUNTING STABILIZER BETWEEN ROW UNITS Planter Mount Bracket Mounting to toolbar using planter mount bracket Mounting directly to toolbar. Slotted holes will accomodate 4, 5, 6 or 7 toolbars. 1-2

Before performing adjustments, lift implement so blade is off ground POST MOUNTING DEPTH ADJUSTMENT 1. Leave chain hooked. 2. Remove bolt. 3. Rotate arm with chain in direction of arrow to set deeper. 4. Replace bolt & tighten securely. Proper Stabilizer depth is achieved when chain is showing some slack with the implement at working depth in the field. 1-3

STABILIZERS AND STABILIZER OPTIONS 601364 SUNCO STABILIZER ASSEMBLY (less mount brackets and no mounting hardware) Coil spring protection with 29 blade and heavy duty 6 bolt hub. 601364 660120 SUNCO STABILIZER HYDRAULIC LIFT KIT Includes cylinder, brackets and hardware. No hoses. 660120

601359 24 STABILIZER MOUNT ARMS for 4x4, 4x7 tool bars Sets stabilizer assembly 24 from tool bar. Requires cross tube and 5/8 bolt package with order. OPTIONAL EQUIPMENT (WHOLEGOODS) STABILIZERS AND STABILIZER OPTIONS 601354 72 STABILIZER MOUNT ARMS for 5x7, 7x7, 4x4, 4x7 tool bars Sets stabilizer assembly 72 from tool bar. Requires cross tube and 5/8 bolt package with order. 601369 60 STABILIZER MOUNT ARMS for 5x7, 7x7, 4x4 tool bars Sets stabilizer assembly 60 from tool bar. Requires cross tube and 5/8 bolt package with order. 601360 48 STABILIZER MOUNT ARMS for 5x7, 7x7, 4x4, 4x7 tool bars Sets stabilizer assembly 48 from tool bar. Requires cross tube and 5/8 bolt package with order. 601365 8 STABILIZER MOUNT ARMS for 7x7, 4x4, 4x7 tool bars Sets stabilizer assembly 8 from tool bar. Requires cross tube and 5/8 bolt package with order. 601561 40 CROSS TUBE Adapts Arms to most cultivators, bedders, etc. (Order 1 with Stabilizer Arms 601354, 601369, 601360, 601359,601365) 601562 66 CROSS TUBE Adapts Arms to most cultivators, bedders, etc. (Order 1 with Stabilizer Arms 601354, 601369, 601360, 601359,601365)

OPTIONAL EQUIPMENT (WHOLEGOODS) STABILIZERS AND STABILIZER OPTIONS 601366 PLANTER STABILIZER MOUNT BRACKETS Bracket mounts on planter 7x7 tool bar, allows for mounting stabilizer between planter row units for planter stabilization. Includes hardware. BOLT PACKAGES (Order with Stabilizer Arms 601354, 601369, 601360, 601359, 601365) Includes U-bolts and hardware for Mount Arms and Cross Tube 450106 5/8 U-Bolts for 5x7 tool bars 450107 5/8 U-bolts for 4x4 tool bars 450108 5/8 U-Bolts for 4x7 tool bars 450109 5/8 U-Bolts for 7x7, 7x5 tool bars U-BOLTS -A- A B C 204275 5/8 x 4 x 5 1/2 (for 4x4 bar) 204276 5/8 x 4 x 8 1/2 (for 4x7 flat bar) 204296 5/8 x 6 x 5 1/2 (for 4x6 bar) 204277 5/8 x 5 x 8 1/2 (for 5x7 flat bar) 204278 5/8 x 7 x 8 1/2 (for 7x7 bar) C B

601361-28 /601362-29 (with WIDE frames) 601364-29 (with NARROW frames) SUNCO STABILIZER (6 BOLT HUB) Less Mount Brackets & Mounting Hardware Narrow Wide Frame Frame Item Part # Part # Description Qty 1 601564 601553 Main Frame 1 2 204341 204340 Spring Torsion 1 3 601563 601560 Arm Pivot 6 Bolt Hub NOT SERVICED 1 3A 601573 Arm Pivot w/spacer - 6 Bolt Hub 1 4 166012 Disc Blade 6 Bolt 28 1 166026 Disc Blade 6 Bolt 29 1 5 601551 Arm Adjusting NOT SERVICED 1 5A 601571 Arm Adjusting with Spacer 1 6 205011 Chain Shackle 5/16 1 7 205001 Chain 1/4 High Test 16 8 480360 Pin 1.25 x 17.625 (wide frame) 1 480362 Pin 1.25 x 12.125 (narrow frame) 1 9 210081K Kit-Hub Assy 6 Bolt (incl. Brgs, seal, 1 lug nuts, cap & items 15, 16, 17, 18) 10 200333 HHCS 1/2 x 1 1/2 Gr. 8 1 11 202116 Washer 1/2 Split Lock 1 12 201116 Nut 1/2-13 Hex 1 13 200130 HHCS 5/16 x 1 Gr. 5 1 14 202110 Washer 5/16 Split Lock 1 15 202222 Washer 7/8 SAE Flat 1 16 201123 Nut 7/8-14 Hex Slotted 1 17 203487 Pin Cotter 5/32 x 1 3/4 1 18 210090 Hub Cap 1 19 210091 Brg Cone Outer LM67048 1 20 210096 Brg Cup Outer LM67010 1 21 210093 Brg Cone Inner JL69349 1 22 210098 Brg Cup Inner JL69310 1 23 210095 Grease Seal CR16289 1 210006* Brg Repair Kit - 6 Bolt Hub 24 210058 Bushing 1.5 OD x 1.25 ID x 1.25 2 25 380115 Weld in Spindle 26 201118 Wheel Nut 1/2-20 6 27 200339 Stud Bolt 1/2-20 x 1 7/8 6 *210006 Bearing Repair Kit includes items 15, 16, 17, 19, 20, 21, 22 and 23. Item Part # Description Qty 28 200327 HHCS 1/2-13 x 1 GR. 5 1 29 202214 Washer 1/2 Flat 2 30 201119 Nut 1/2-13 Whiz Lock 1 MOUNTING HARDWARE NOT INCLUDED: TO MOUNT TO CROSS TUBE PART #601561 OR TO MOUNT TO 2 1/2 DIAMOND BAR Part # Description Qty 200463 HHCS 5/8-11 x 1 3/4 (not shown) 6 31 201120 Nut 5/8-11 Hex 6 32 202120 Washer 5/8 Split Lock 6 33 202218 Washer 5/8 Flat 6 34 315204 Half Clamp 2 35 315041 U-Bolt 5/8-11 x 5 Tri-bend 2 NOTE: TO DETERMINE WHICH STABILIZER YOU HAVE, MEASURE THE WIDTH OF THE FRAME. WIDE FRAME MEASURES 17.25 ; NARROW FRAME MEASURES 11.5 601371 - Kit - Spacer Fix Weld-on Replaces 480361 & 480363 Rev. 10/15

Quality Products from SUNCO SUNCO Saber Tooth Floating Row Cleaners Floating parallel arms allow the Floating Saber Tooth to follow the contours of the field consistently clearing residue Polymer Depth Bands create flotation in soft soil conditions and minimize soil buildup in wet conditions Compatible with the SUNCO NutriMate 3 TM Row Unit Mounted Precision Fertilizer Attachment Sunco NutriFloater Shown Place fertilizer in the root zone for the most efficient use of costly fertilizer Pivoting and pulling actions reduce down pressure requirements on row unit 3 vertical and 2 horizontal adjustments standard Available in Liquid and Dry Versions NutriFloater compatible with the CleanSweep System (Not Included) Pin Adjust to Floating Upgrade kits now available CleanSweep System (Not Included) Optional Spring Down Pressure Kit features built in spring adjustment tensioner for additional down-force in high residue conditions NutriMate 3 Floating Saber Tooth Models also available. Pin Adjust to Floating Upgrade kits now available SUNCO Saber Tooth Row Cleaners Remove MORE yield robbing Trash SUNCO Acura Trak SUNCO Stabilizer TM Do herbicide resistant weeds SUNCO Implement Guidance Hitch TM When guess row accuracy is critical: have you considering cultivation? Available in the NEW easy to Maximize accuracy with AcuraTrak access Screw Adjust or in the implement guidance. Original Pin models Due to sloped terrain or Narrow Row Models also farming practices such as strip till available Maximize RTK Efficiency Industry Exclusive Tooth Design, Available for Planters, Disc Concavity and Disc Separation Cultivators, Bedders and STOP IMPLEMENT DRIFT Strip Till Machines Since 1987» Works in any Row Crop Sunco Crop Sensing» Provides implement Wands guidance with or WITHOUT GPS» Sensing Options include: Crop Sensing Wands Universal crop Mark Guide Weights sensing wands can be set to sense off Furrow Guide one or two rows. Weights This gives the TrueTracker Acura Trak excellent performance in both small and large Active Implement crops and trashy conditions. Guidance All Models Use Heavy Duty Cast Hubs With 2 Triple Seal Bearings PROPPED NOT PROPPED SUNCO Prop Water Run Off & Soil Erosion Keep PROFITS from running off your fields Water soaks in. Water runs off. Efficiently steers the implement from the front not the rear Solves mounting issues common to toolbar mounted systems Is able to steer on the headlands and in reverse with the implement raised Does not change the pull point of the implement, maximizing GPS accuracy 800-676-2146 www.suncomarketing.com 170328DPF

SUNCO MARKETING P. O. Box 2036 North Platte, NE 69101 (308) 532-2146 Fax: (308) 534-0938 PART #250019