Type No. Catalog No. Job. Name ELMGR Compact Fluorescent Series Element Glass (glass lined) High Bay PPLICTIONS pplications include large and small retail facilities, lobbies, conference rooms, auditoriums and other commercial and light industrial spaces. CONSTRUCTION cylindrical ballast housing features a tool-less wiring access door for simple installation and maintenance. Single baffle is standard. Dual or Tri-Baffle option may be specified. Ballast housing has an Ultra-Clad polyester powder coating, electrostatically applied and oven cured. Standard colors and five new metallic finishes available. Custom RL colors may be specified. Custom designed multicolor luminaire may be specified. OPTICS The glass-lined reflector features borosilicate glass optics covered with a metal high bay reflector overlay whose color may be specifies. The ELMGR series is available in Wide distribution and either Open or Enclosed construction. Enclosed units feature a clear or diffuse tempered glass lens and metal lens frame. ELECTRICL Unit features a high power factor, high frequency (non-dimming) electronic ballast with reliable starting at temperatures as low as -30 C (-22 F). Total harmonic distortion is less than 10%. Full range dimming ballasts are optional. Starting temperatures are as low as 10 C (50 F), and THD varies. Dimming ballast is not available with EBB accessory. Unit may be specified with a standard dimming range to 5% lumen output. The Element Compact Fluorescent series utilizes amalgam-based compact fluorescent lamps and GX24q-4/5 sockets. MOUNTING Standard pendant mounting features a cast aluminum nut and hub to provide quick, positive mounting to 3/4 NPT or NPSM conduit. WRRNTY/LISTINGS Standard 3 Year Limited Warranty. UL/cUL Listed luminaire, UL 1598, 40 C (104 F) rated, suitable for damp locations. The quality systems of this facility have been Registered by UL to the ISO 9000 Series Standards. Custom multi-color option shown for reference only. ELMGR - Open optics 14.1 (35.81cm) C 14.1 (35.81cm) C B B ELMGR - Enclosed optics See Page 2 for Ordering Information
Element Glass (glass lined) High Bay Element Rodded Metal over Glass High Bay 16 open, standard single baffle Series Compact Fluorescent r ELCF-126 Optics r MGR16WO = 16 distribution, Open Voltage / E ballast / Dimming Voltage: r 120 r 208 r 240 r 277 r ELCF-226 r ELCF-426 r ELCF-132 r ELCF-232 r ELCF-432 r MGR16WE = 16 Clear lens r MGR16WD = 16 Diffuse lens Electronic ballast type: r E Electronic ballast (standard) lternately, a specific manufacturer s product may be selected. Consult factory. r E2 = Universal r E3 = ce r E4 = dvance Ballast Ordering Examples: r ELCF-142 r ELCF-242 r ELCF-442 r MGR22WO = 22 distribution, Open r MGR22WE = 22 Clear lens Standard non-dimming 120v 208v 240v 277v ballast: 120E 208E 240E 277E E2, E3 or E4 non-dimming: ballast manufacturer 120v 208v 240v 277v Universal ce dvance 120E2 208E2 240E2 277E2 120E3 208E3 240E3 277E3 120E4 208E4 240E4 277E4 Notes 1) In the ies file, elmgcf denotes element, metal over glass, compact fluorescent. Wattage abbreviations: 126 = 26W (single lamp), 226 = 2 x 26W (twin lamp), 426 = 4 x 26W (quad lamp), 132 = 32W (single lamp), 232 = 2 x 32W (twin lamp), 432 = 4 x 32W (quad lamp), 142 = 42W (single lamp), 242 = 2 x 42W (twin lamp), 442 = 4 x 42W (quad lamp). Optics abbreviations: s = 16 (small), l = 22 (large), distribution/ construction: w = wide/open, we = wide/enclosed with clear glass lens, wd = wide/enclosed with diffuse glass lens. r MGR22WD = 22 Diffuse lens Distribution Guide and Ballast Data Dimming: Optional dimming ballast s range is down to 5% lumen output. Leave blank to specify non-dimming ballast. r D = nalog dimming (E4 ballasts only) Wattage Optics lamping ies (1) Line Current Line Dia. File Name 120 / 208 / 240 / 277 Watts CF 126 16 1 x 26W elmgcf126s*.ies 0.26 / 0.19 / 0.14 / 0.10 30 22 elmgcf126l*.ies CF 226 16 2 x 26W elmgcf226s*.ies 0.46 / 0.31 / 0.25 / 0.19 56 22 elmgcf226l*.ies CF 426 16 4 x 26W elmgcf426s*.ies 0.92 / 0.62 / 0.50 / 0.38 112 22 elmgcf426l*.ies CF 132 16 1 x 32W elmgcf132s*.ies 0.27 / 0.17 / 0.14 / 0.12 33 22 elmgcf132l*.ies CF 232 16 2 x 32W elmgcf232s*.ies 0.52 / 0.34 / 0.27 / 0.22 64 22 elmgcf232l*.ies CF 432 16 4 x 32W elmgcf432s*.ies 1.04 / 0.68 / 0.54 / 0.44 128 22 elmgcf432l*.ies CF 142 16 1 x 42W elmgcf142s*.ies 0.35 / 0.23 / 0.18 / 0.18 43 22 elmgcf142l*.ies CF 242 16 2 x 42W elmgcf242s*.ies 0.74 / 0.46 / 0.36 / 0.31 84 22 elmgcf242l*.ies CF 442 16 4 x 42W elmgcf442s*.ies 1.48 / 0.92 / 0.72 / 0.62 168 22 elmgcf442l*.ies
ELMGR Compact Fluorescent Series Element Glass (glass lined) High Bay Finish options Standard colors Decorator colors r WHT Custom Multi-color Luminaire r PRL Smooth White (Default ballast finish if color is not specified.) Pearl Defined by Custom Submittal Drawing available on website Consult factory for assistance. r MC(XXX) = Custom Multi-Color r TWHT Simple two-color Element Custom Multi-Color Luminaire Example: White r TBK r PWT r TS r CRL r TGR r BGE r TDB r TER Decorator colors Terra and Beige are shown. Pewter Black Satin luminum Charcoal Gray Beige Dark Bronze Terra First, specify overall custom ballast color. Lens trim color on enclosed units is typically the same as ballast color, but may be specified to match baffle if desired. Second, specify contrasting baffle color. Single Baffle is standard. r TGN Green RL color may also be specified. r RL(X) X = Custom RL color number Consult factory The baffles in a Dual Baffle or Tri-Baffle option are typically specified as the same contrasting color on a Custom Multi-Color unit. However, any combination of colors may be specified as defined by the Custom Submittal Drawing. In the case of the Element Rodded Metal over Glass series, the outer reflector color may also be specified.
Element Glass (glass lined) High Bay Options (Factory Installed) Decorative Baffle Options r BD Dual Baffle r BT Tri-Baffle Note: Single Baffle is standard. Decorative Suspended Cable Mounting For Non-Dimming units r CC(X) Suspended Cable Mount Luminaire with single Coil Cord r CS(X) Suspended Cable Mount Luminaire with single Straight Cord (X) = Cord length in feet: 3, 6 or 8 For Dimming units When Element luminaires with dimming capabilities are specified with a suspended cable mount option, the use of both the straight and coil cords is required. central straight cable carries the low voltage dimming leads to the ballast and a coil cord supplies ballast and lamp power. Upper mounting plate detail at right shows the luminaire suspension cables and the straight and coil cord combination. Decorative Suspended Cable Mount Lower Lens Lens size dependent on optics. Optics Nominal Diameter Lens Diameter Hole Diameter 19 and below 24.0 (60.96cm) 9.5 (24.13cm) 22 and above 32.0 (81.28cm) 13.5 (34.29cm) Solid Suspended Glass Lens: r L1C Solid suspended Clear glass lens r L1D Solid suspended Diffuse glass lens Note: The suspended lens option is shown with Metal over Glass optics (ELMG). detail: lens suspend fitting and cable connection at baffle detail: lens suspend fitting and cable connection at lens Suspended Lens with center opening: r L2C Suspended Clear glass lens with center opening r L2D Suspended Diffuse glass lens with center opening Silkscreened Clear Suspended Lens: r L1S = Silkscreened clear glass lens r L2S = Silkscreened clear glass lens with center opening Consult factory. May be specified by ink color, dot pattern, or by client determined logo art or design.
Element Glass (glass lined) High Bay Ballast Fusing r F1 = Single Fuse, 120 / 277V r F2 = Double Fuse, 208 / 240V lternate Mounting r HCP-(X)C-L(Y)20P = Hook, Cord and Plug, 3-Wire r HCP-(X)C-L2320P = Hook, Cord and Plug, 5-Wire r H4-HCP-L(Y)20P = Pendant Power Hook, 3-Wire (300V) with HCP r H4-HCP-L2320P = Pendant Power Hook, 5-Wire (600V) with HCP r LCP-(X)C-L(Y)20P = Loop, Cord and Plug, 3-Wire r LCP-(X)C-L2320P = Loop, Cord and Plug, 5-Wire r H5-LCP-L(Y)20P = Power Hook, 3-Wire (300V) with LCP r H5-LCP-L2320P = Power Hook, 5-Wire (600V) with LCP Unit is pre-wired with 3-conductor rubber jacketed cable and heavy duty (16/3) NEM twist-lock plug, along with die-cast hook with locking screw. 20 standard. Pendant Mounted Power Hook with NEM receptacle. Unit is pre-wired with Hook, Cord and Plug. Unit is pre-wired with 3-conductor rubber jacketed cable and heavy duty (16/3) NEM twist-lock plug, with diecast loop. 20 standard. Power Hook with thru-wire provision contains a NEM receptacle. Unit is prewired with Loop, Cord and Plug. Ballast Safety Cable Not available on units with suspended cable option. r SC3 3 Safety Cable r SC6 6 Safety Cable r SC10 10 Safety Cable ccessories (Field Installed - Shipped Separately) Ballast Fusing r F1-Kit = Single Fuse, 120 / 277V r F2-Kit = Double Fuse, 208 / 240V lternate Mounting r HCP-(X)C-L(Y)20P = Hook, Cord and Plug, 3-Wire r HCP-(X)C-L2320P = Hook, Cord and Plug, 5-Wire r H4 = Pendant Power Hook, 3-Wire r H4-5W = Pendant Power Hook, 5-Wire 3-conductor rubber jacketed cable and heavy duty (16/3) NEM twist-lock plug as specified, with diecast hook with locking screw. 20 standard. Pendant Mounted Power Hook with NEM receptacle as specified. Used with corresponding Hook, Cord and Plug. r LCP-(X)C-L(Y)20P = Loop, Cord and Plug, 3-Wire 3-conductor rubber jacketed cable and heavy duty (16/3) NEM twist-lock plug as specified, with die-cast loop. 20 standard. r LCP-(X)C-L2320P = Loop, Cord and Plug, 5-Wire r H5 = Power Hook with thru-wire provision, 3-Wire r H5-5W = Power Hook with thru-wire provision, 5-Wire Power Hook with thru-wire provision contains a NEM receptacle. Used with corresponding Loop, Cord and Plug. Mounting Extras r HM Hook Male r LM Loop Male r J75 Joint ligner 50 lb. maximum allowed. r SH75 Swivel Hanger 50 lb. maximum allowed if hung from junction box.
Element Glass (glass lined) High Bay r LMP(XX) = Lamped (standard) XX = Specify Lamp Color Temperature: 27, 30, 35, or 41 41 = 41K (4100K Lamp) (1) 35 = 35K (3500K Lamp) 30 = 30K (3000K Lamp) 27 = 27K (2700K Lamp) CF Lamps shipped separately. (1) If lamp Color Temperature is not specified with this option, ELGR CF unit is shipped with 41K lamps. Emergency Battery Backup type r EBB remote mount, dry location (standard) r EBB-DL remote mount, damp location option r EBBP r EBBS pendant mount, dry location only surface mount, dry location only - lumen package - (voltage) - test switch type r 750-120-MT r 750-277-MT r 1000-120-MT r 1000-277-MT r 1000-120-ST r 1000-277-ST 750 lumens, 120V, manual test switch 750 lumens, 277V, manual test switch 1000 lumens, 120V, manual test switch 1000 lumens, 277V, manual test switch 1000 lumens, 120V, self test switch 1000 lumens, 277V, self test switch EBB or EBB-DL Fixture is supplied with remotely mounted emergency battery backup. Includes ballast housing, two 24 sections of 3/8 flex conduit, charging indicator light, and test switch. Mounting dimensions dependant upon ballast type. Consult factory. EBBP Fixture is supplied with emergency battery backup in a decorative aluminum housing for pendant mount to 3/4 NPT rigid conduit (by others). White finish standard. Includes charging indicator light, and test switch which may be remote mounted. Mounting dimensions dependant upon ballast type. Consult factory. EBBS Fixture is supplied with emergency battery backup in a decorative aluminum housing with surface mounting brackets. Requires a minimum of 28 of 3/4 flex conduit each side (by others). White finish standard. Includes charging indicator light, and test switch which may be remote mounted. Mounting dimensions dependant upon ballast type. Consult factory. Wireguard r WG-XX = Wireguard (X) = Optics diameter in inches: 16 or 22 Notes For maximum endurance in active environments, the lens may be protected with a wireguard. Not available with decorative suspended cable mount lower lens options (L1C, L1D, L1S, L2C, L2D, L2S). Philips Lighting Company 200 Franklin Square Drive Somerset, NJ 08873 Phone: 855-486-2216 Philips Lighting Company 281 Hillmount Road Markham ON, Canada L6C 2S3 Phone: 800-668-9008