TABL OF CONTNTS Specifications... 6-2 QuickSpecGuide... 6-4 levations:1/4 Scale... 6-6 Double-Hung... 6-9 Double-Hung Picture... 6-16 Double-Hung Picture with Flankers... 6-26 SectorTop... 6-28 FullRadius... 6-34 Transoms... 6-35 SashGlazingOptions:3 Scale... 6-37 Trim&SillOptions:3 Scale... 6-38 JambOptions:3 Scale... 6-40 Standard Mullion Options... 6-41 LiteCutInformation... 6-43 ClearOpeningandDaylightSpecifications... 6-46 Unit Sizing, Rough Openings & Masonry Openings... 6-59 SectionDetails:6 Scale... 6-61 Angle Bay Specifications and Rough Opening Information... 6-72 SectionDetails:3 Scale(AngleBay)... 6-74 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-1
XTRIOR FINISH All exterior surfaces are covered with a factory-applied latex primer. AURALAST R WOOD AuraLast R wood is fundamentally different from wood resulting from traditional millwork preservation processes in that it uses a proprietary vacuum/pressure process to provide protection throughout the wood parts used to make windows and doors. AuraLast R wood is distinguished from wood using the current preservation methods by its unique ability to achieve greater penetration of the active ingredients into the wood parts, with a penetration of the treatment being a minimum of 92%. INTRIOR FINISH All interior surfaces are unfinished clear pine ready for on site finishing. Primed and pre-finished interiors are available in paint: Pure White, xtra White, Natural Choice, Moderate White; in stain: Wheat, Cherry, Cordovan; and Clear Lacquer. FRAM Frame is assembled from select kiln dried pine using AuraLast R wood on all exterior parts. Frame corner joints are tightly secured with metal fasteners and adhesive. Frame thickness is 11/16 (17.5mm) at head, side jamb and sill. Basic jamb width is 4-9/16 (116mm) and may be extended for different wall depths. Finished frame has exterior casing, sill nosing, weather-stripping, hardware, and interior stops applied. SASH Sash is 1- (36.5mm) thick select kiln-dried pine using AuraLast R wood. Stiles and rails are mortise and tenoned, machine clamped for squareness and secured with metal fasteners. The glass is mounted into the sash using a silicone-glazing compound on the exterior and acrylic sealant on the interior, then secured with interior applied profiled wood stops. Sash operate in a non-compression ivory colored jamb liner that allows both top and bottom sash to tilt inside for easy cleaning and removal without the use of tools. No finger plow sash available on venting units. GLAZING 3/4 (19mm) thick sealed insulating glass is constructed from two panes of glass, utilizing a continuous roll formed stainless steel spacer with dual seal sealant. The glass is mounted into the sash using a silicone-glazing compound and secured with interior applied profiled wood stops. All insulating glass units comply with the performance requirements of IGCC in accordance with either ASTM 774 or 2190. GLAZING OPTIONS 3/4 insulating glass available in Low- with Argon, Low-, Low- 366, Clear, Neat Glass, reflective, tinted, or obscure, tempered or other specialty glass as specified. Preserve film is a 0.003 thick polyethylene film with a low tack acrylic adhesive applied to the glass for protection during shipping and installation. 4,000 foot elevations and higher require a capillary tube to equalize environmental stress (otherwise known as High Altitude glazing). High Altitude glazing does not allow the use of Argon as listed under glazing options. WATHR-STRIPPING ngineered system combines PVC ivory jamb liner with dual bulb weather-stripping at head. Checkrail features thermoplastic rubber bulb and recessed cam action sash lock for secure closure. Rigid vinyl water stops at sill provide additional restraint against weather. PRODUCT SPCIFICATIONS HARDWAR Sash operate by means of a dual block and tackle balance system with nylon roller pulleys and high-tension coil springs. Balance system gauged to sash weight and uses pre-stretched dacron cords attached to clutch mechanisms to insure smooth, operation and compliance with operating force requirements. Jamb liners are Ivory (White is optional). Recessed cam action sash lock is available in White, Chestnut Bronze, Desert Sand or optional Bright Brass, Antique Brass, Polished Brass, Brushed Chrome or Imitation Oil Rubbed Bronze. 28 glass width and larger units have two sash locks. Optional Lexan sash lift available for no finger plow sash. XTRIOR INSCT SCRNS Charcoal fiberglass screen cloth (18x16 mesh) set in painted roll formed aluminum frame with color to match cladding - choice of Brilliant White, Chestnut Bronze, Desert Sand, French Vanilla, Hartford Green, Mesa Red, Black, Arctic Silver or Dark Chocolate, installed in channel on frame extrusion and held in place with spring loaded plungers at the top and sides of screen. Aluminum mesh and Phantom screen also available. Insect screens are intended to allow air and light in and to keep insects out. They are not intended to keep anyone or anything from falling through an open window. For safety screens or other security devices contact your local building supply retailer. GRILLS SDL (Simulated Divided Lites) - wood muntins permanently applied to the exterior of the insulating glass unit (not available on textured glass) in 7/8 (22mm), 1-1/8 (28.5mm), or 1-3/8 (34.9mm) widths. SDL is standard with a light bronze internal shadow bar to give a true divided lite appearance. As an option, SDL may be ordered with a silver shadow bar. Clear wood interior muntin bars match the exterior muntin width and are permanently bonded to the interior of the glass. Also available is a 2-5/16 (59mm) SDL bar, which simulates a double-hung checkrail. Full Surround Wood Grilles - Rectangular unfinished clear pine wood grilles in 7/8 (22mm) are available in patterns selected by the owner. GBG (Grilles between the Glass) - 5/8 (15.9mm) flat and 23/32 or 1 contour mounted between the glass panes suspended within the air cavity. XTRIOR TRIM 1-3/32 (27.8mm) x 2 (50.8mm) brickmould with 1-1/16 (27mm) x 1-3/4 (44.5mm) nosing is standard. Flat casing is available as 1-3/32 (27.8mm) x 2 (50.8mm), 1-3/32 (27.8mm) x 3-1/2 (89mm), 1-3/32 (27.8mm) x 4-1/2 (114.3mm), and 1-3/32 (27.8mm) x 5-1/2 (139.7mm). The following profiled casings are available: RB-3 and Adams as 1-1/16 x 3-1/2 (89mm), and Williamsburg 1-3/16 x 3-1/4. Historical wood sill nosing 1-3/4 (44.5mm) and 2-13/16 (71.4mm) is also available. Continued on next page October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-2
XTNSION JAMBS xtension jambs are factory applied to the interior on all four sides of the frame and are 4/4 standard thick pine to accommodate wall depths up to 9-5/16 with one piece, and up to 12 with two pieces. 9/16 (14.2mm) option also available. INSTALLATION Installation per JLD-WN Installation Method for Wood Windows JII003 or JII012. See www.jeld-wen.com/resources for instructions. PRODUCT SPCIFICATIONS PRFORMANC NFRC Certified - (Rated and labeled in accordance with NFRC) WDMA Hallmark Certified - In accordance with AAMA/NWWDA/101/I.S.2-97 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-3
QUICK SPC GUID SPCIFICATION STANDARD FATURS OPTIONAL FATURS Some options may require additional lead times. Consult your JLD-WN Sales Representative. FRAM S Fingerjoint Wood XTRIOR FINISH S Primed S Natural XTRIOR TRIM S 1-3/32 Brickmould S Drip Cap INTRIOR FINISH S Natural S Priming Available S Flat Casing: 1-3/32 x 2, 3-1/2, 4-1/2, and 5-1/2 S Williamsburg Casing: 1-3/16 x 3-1/4 S RB-3 Casing: 1-1/16 x 3-1/2 S Adams Casing: 1-1/16 x 3-1/2 S 1X4 Backband Casing: 1-7/32 x 4-1/2 S 2 Historical Nosing S No Brickmould Option SIZ S Width: Venting Double-Hung: 21-3/8, 25-3/8, 29-3/8, 31-3/8, 33-3/8, 37-3/8, 41-3/8, 45-3/8 Picture Double-Hung: 21-3/8, 25-3/8, 29-3/8, 31-3/8, 33-3/8, 37-3/8, 41-3/8, 45-3/8, 49-3/8, 53-3/8, 61-3/8, 69-3/8, 77-3/8 Pre-finished Interior Options are: S Paint - Pure White, xtra White, Natural Choice, Moderate White S Stain - Wheat, Fruitwood, Cherry, Cordovan S Clear Lacquer S Width: Venting Double-Hung: Minimum: 16 Maximum: 45-3/8 Picture Double-Hung: Minimum: 16 Maximum: 77-3/8 Fixed Units over 49-3/8 wide can be up to 80 high Fixed Units up to 49-3/8 wide can be up to 92 high S : Venting Double-Hung: 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 88, 92 S : Venting Double-Hung: Minimum: 28 Maximum: 92 * * glass can t exceed 42 high Picture Double-Hung: 15, 18, 24, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 88, 92 Picture Double-Hung: Minimum: 15 Maximum: 92 Fixed Units over 49-3/8 wide can be up to 80 high Fixed Units up to 49-3/8 wide can be up to 92 high S For RO, add 3/4 S For RO, add 3/4 GLAZING S Low- Insulating Glass S Preserve Protective Film S Clear S Obscure S Bronze S Low- 366 S S S Neat Glass Reflective Tempered S High Altitude Continued on next page October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-4
QUICK SPC GUID SPCIFICATION STANDARD FATURS OPTIONAL FATURS Some options may require additional lead times. Consult your JLD-WN Sales Representative. GRILLS S 5/8 Flat, 23/32 or 1 Contour GBG S 7/8 Full Surround Wood Grilles SDL Bead Profile: S 7/8, 1-1/8, 1-3/8, 2-5/16 with Light Bronze Shadow Bar S 7/8, 1-1/8, 1-3/8, 2-5/16 with Silver Shadow Bar HARDWAR S Balance: Dual Block and Tackle S Cam Locks S Ivory Jamb Liners (standard) HARDWAR COLOR S White S Desert Sand S Chestnut Bronze S S S S White Antique Brass Polished Brass Brushed Chrome JAMB S 4-9/16 S Minimum: 4-9/16 S Maximum: 9-5/16 (one piece) S Maximum: 12 (two piece) S Imitation Oil Rubbed Bronze SCRNS S Fiberglass S Aluminum Mesh available S Phantom Screen - some size limitations apply SCRN FRAM COLOR S Brilliant White S Chestnut Bronze S Desert Sand S French Vanilla S Mesa Red S S S S Hartford Green Black Arctic Silver Dark Chocolate October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-5
GNRAL INFORMATION DOUBL-HUNG DIMNSIONAL WINDOWS Wood double-hung windows may be specified as dimensional by adjusting the desired rough opening width or height in 1/4 increments from standard. Wood double-hung windows feature fully operating upper and lower sash. Counterbalancing is achieved with block and tackle spring extension systems hidden in weatherable PVC jambliners. Operating units are supplied with cam-type sash locks installed. Die-cast lower sash lifts supplied for field installation are an option. Recessed sash retainers provide simple sash installation and removal. There are several hardware finish options. Refer to the Specifications for available finish options. MULTIPL ASSMBLIS Wood double-hung windows may be mulled beside other wood double-hungs or wood picture windows, or below wood transom windows, to fulfill a wide variety of needs. Factory assembled mulls are limited in height (100 ), width (114 ), and a total area (75 square feet). October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-6
HANDING & OPRATION DOUBL-HUNG DOUBL-HUNG OPRATION: When the sash are locked at the check rails the sash are closed and sealed in the sash opening of the frame. When the sash are unlocked the lower sash travels vertically to any position desired. The upper sash can also be positioned as desired. SASH TILTING FOR WASHING The Custom Double-Hung window will allow the sash to be tilted or removed for easy cleaning. October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-7
LVATION NOTS DOUBL-HUNG LVATION DRAWINGS UTILIZ A LIMITD NUMBR OF PROJCTD LINS TO PRODUC A RUDIMNTARY DRAWING INTNDD TO B USD IN A SMALL GRAPHICAL SCAL. LVATIONS AR VIWD PRPNDICULAR FROM TH XTRIOR OF TH STRUCTUR. IF MOR DIMNSIONS AR NDD, US TH SCTION DRAWINGS FOR MOR COMPLT DPICTIONS. M.O. Brickmould M.O. Adams/Flat Casing Rough Opening Frame Size Daylight Opening 24 1/2 (622) 27 1/2 (699) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) Masonry Openings for Brickmould, Flat & Adams Casing. Vertical measurements include sillnose. (Subtract 1/2 from Masonry Opening for Unit Size) 34 11/16 (881) 36 3/16 (919) 32 3/4 (832) 32 (813) 11 1/16 (281)[2] DAYLIGHT OPNING WD2132 OUTSID OF XTRIOR TRIM COTTAG STYL WINDOWS BOOK CODS UNIT WIDTH WD2148C UNIT HIGHT C = COTTAG WD INDICATS SITLIN X WOOD DOUBL-HUNG TH FIRST TWO NUMBRS INDICAT TH UNIT WIDTH BOOK COD TH LAST TWO NUMBRS INDICAT TH UNIT HIGHT GNRAL WOOD DOUBL-HUNG NOTS LVATION SYMBOL LGND: 1. ALL UNITS SHOWN AR AVAILABL AS OPRATORS ONLY. 2. UNIT LVATIONS AR SHOWN WITH BRICKMOULD & SILL NOS. 3. ALL OPRATING SASH AR INSTALLD WITH VINYL JAMB LINRS AND OPRATD WITH AN INTRNAL BLOCK AND TACKL SPRING SYSTM. 4. DIMNSIONAL VALUS IN PARNTHSS AR MILLIMTR CONVRSIONS. 5. VALUS IN BRACKTS AR NUMBR OF DAYLIGHT OPNINGS. MO MASONRY OPNING October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-8
1-WID UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 24 1/2 (645) 27 1/2 (699) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) 28 1/2 (724) 31 1/2 (800) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 1/2 (826) 35 1/2 (902) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 1/2 (876) 37 1/2 (953) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 1/2 (927) 39 1/2 (1003) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 1/2 (1029) 43 1/2 (1105) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 1/2 (1130) 47 1/2 (1207) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) 34 11/16 (881) 36 3/16 (919) 32 3/4 (832) 32 (813) 11 1/16 (281)[2] WD2132 WD2532 WD2932 WD3132 WD3332 WD3732 WD4132 38 11/16 (983) 40 3/16 (1021) 36 3/4 (933) 36 (914) 13 1/16 (332)[2] WD2136 WD2536 WD2936 WD3136 WD3336 WD3736 WD4136 42 11/16 (1084) 44 3/16 (1122) 40 3/4 (1035) 40 (1016) 15 1/16 (383)[2] WD2140 WD2540 WD2940 WD3140 WD3340 WD3740 WD4140 46 11/16 (1186) 48 3/16 (1224) 44 3/4 (1137) 44 (1118) 17 1/16 (433)[2] WD2144 WD2544 WD2944 WD3144 WD3344 WD3744 WD4144 50 11/16 (1287) 52 3/16 (1326) 48 3/4 (1238) 48 (1219) 19 1/16 (484)[2] WD2148 WD2548 WD2948 WD3148 WD3348 WD3748 WD4148 56 3/4 (1441) 56 (1422) 54 11/16 (1389) 56 3/16 (1427) 52 3/4 (1340) 52 (1321) 21 1/16 (535)[2] WD2152 WD2552 WD2952 WD3152 WD3352 WD3752 WD4152 58 11/16 (1491) 60 3/16 (1529) 23 1/16 (586)[2] WD2156 WD2556 WD2956 WD3156 WD3356 WD3756 WD4156 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT BASIC UNIT CLAR OPNING XCDS 20 IN WIDTH, 24 IN HIGHT & A MINIMUM OF 5.7 SQ. FT. ##* NUMBR INDICATS STANDARD DSIGN PRSSUR (DP) RATING. ##** NUMBR INDICATS OPTIONAL DSIGN PRSSUR (DP) RATING. Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-9
1-WID UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 24 1/2 (645) 27 1/2 (699) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) 28 1/2 (724) 31 1/2 (800) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 1/2 (826) 35 1/2 (902) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 1/2 (876) 37 1/2 (953) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 1/2 (927) 39 1/2 (1003) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 1/2 (1029) 43 1/2 (1105) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 1/2 (1130) 47 1/2 (1207) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) 74 11/16 (1897) 76 3/16 (1935) 68 3/4 (1746) 68 (1727) 35 1/16 (891) 23 1/16 (586) 72 3/4 (1848) 72 (1829) 31 1/16 (789)[2] 70 11/16 (1795) 72 3/16 (1834) 68 3/4 (1746) 68 (1727) 29 1/16 (738)[2] 66 11/16 (1694) 68 3/16 (1732) 64 3/4 (1645) 64 (1626) 27 1/16 (687)[2] 62 11/16 (1592) 64 3/16 (1630) 60 3/4 (1543) 60 (1524) 25 1/16 (637)[2] WD2160 WD2560 WD2960 WD3160 WD3360 WD3760 WD4160 WD2164 WD2564 WD2964 WD3164 WD3364 WD3764 WD4164 WD2168 WD2568 WD2968 WD3168 WD3368 WD3768 WD4168 70 11/16 (1795) 72 3/16 (1834) WD2168C WD2568C WD2968C WD3168C WD3368C WD3768C WD4168C WD2172 WD2572 WD2972 WD3172 WD3372 WD3772 WD4172 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT BASIC UNIT CLAR OPNING XCDS 20 IN WIDTH, 24 IN HIGHT & A MINIMUM OF 5.7 SQ. FT. ##* NUMBR INDICATS STANDARD DSIGN PRSSUR (DP) RATING. ##** NUMBR INDICATS OPTIONAL DSIGN PRSSUR (DP) RATING. Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-10
1-WID UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 24 1/2 (645) 27 1/2 (699) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) 28 1/2 (724) 31 1/2 (800) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 1/2 (826) 35 1/2 (902) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 1/2 (876) 37 1/2 (953) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 1/2 (927) 39 1/2 (1003) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 1/2 (1029) 43 1/2 (1105) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 1/2 (1130) 47 1/2 (1207) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) 94 11/16 (2405) 96 3/16 (2443) 92 3/4 (2356) 92 (2337) 41 1/16 (1043)[2] 90 11/16 (2303) 92 3/16 (2342) 88 3/4 (2254) 88 (2235) 39 1/16 (992)[2] 82 11/16 (2100) 84 3/16 (2138) 80 3/4 (2051) 80 (2032) 35 1/16 (891)[2] 78 11/16 (1999) 80 3/16 (2037) 76 3/4 (1949) 76 (1930) 33 1/16 (840)[2] WD2176 WD2576 WD2976 WD3176 WD3376 WD3776 WD4176 WD2180 WD2580 WD2980 WD3180 WD3380 WD3780 WD4180 WD2188 WD2588 WD2988 WD3188 WD3388 WD3788 WD4188 WD2192 WD2592 WD2992 WD3192 WD3392 WD3792 WD4192 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT BASIC UNIT CLAR OPNING XCDS 20 IN WIDTH, 24 IN HIGHT & A MINIMUM OF 5.7 SQ. FT. ##* NUMBR INDICATS STANDARD DSIGN PRSSUR (DP) RATING. ##** NUMBR INDICATS OPTIONAL DSIGN PRSSUR (DP) RATING. Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-11
1-WID UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 1/2 (1232) 51 1/2 (1308) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 1/2 (1232) 51 1/2 (1308) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 1/2 (1232) 51 1/2 (1308) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) 34 11/16 (881) 36 3/16 (919) 32 3/4 (832) 32 (813) 11 1/16 (281)[2] 38 11/16 (983) 40 3/16 (1021) 36 3/4 (933) 36 (914) 13 1/16 (332)[2] WD4532 62 11/16 (1592) 64 3/16 (1630) 60 3/4 (1543) 60 (1524) 25 1/16 (637)[2] WD4560 78 11/16 (1999) 80 3/16 (2037) 76 3/4 (1949) 76 (1930) 33 1/16 (840)[2] WD4536 WD4576 42 11/16 (1084) 44 3/16 (1122) 40 3/4 (1035) 40 (1016) 15 1/16 (383)[2] WD4540 66 11/16 (1694) 68 3/16 (1732) 64 3/4 (1645) 64 (1626) 27 1/16 (687)[2] WD4564 82 11/16 (2100) 84 3/16 (2138) 80 3/4 (2051) 80 (2032) 35 1/16 (891)[2] 46 11/16 (1186) 48 3/16 (1224) 44 3/4 (1137) 44 (1118) 17 1/16 (433)[2] WD4544 70 11/16 (1795) 72 3/16 (1834) 68 3/4 (1746) 68 (1727) 29 1/16 (738)[2] WD4580 50 11/16 (1287) 52 3/16 (1326) 48 3/4 (1238) 48 (1219) 19 1/16 (484)[2] WD4568 90 11/16 (2303) 92 3/16 (2342) 88 3/4 (2254) 88 (2235) 39 1/16 (992)[2] 54 11/16 (1389) 56 3/16 (1427) 52 3/4 (1340) 52 (1321) 21 1/16 (535)[2] WD4548 70 11/16 (1795) 72 3/16 (1834) 68 3/4 (1746) 68 (1727) 35 1/16 (891) 23 1/16 (586) WD4588 WD4568C 58 11/16 (1491) 60 3/16 (1529) 56 3/4 (1441) 56 (1422) 23 1/16 (586)[2] WD4552 74 11/16 (1897) 76 3/16 (1935) 72 3/4 (1848) 72 (1829) 31 1/16 (789)[2] 94 11/16 (2405) 96 3/16 (2443) 92 3/4 (2356) 92 (2337) 41 1/16 (1043)[2] WD4556 WD4572 WD4592 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT BASIC UNIT CLAR OPNING XCDS 20 IN WIDTH, 24 IN HIGHT & A MINIMUM OF 5.7 SQ. FT. ##* NUMBR INDICATS STANDARD DSIGN PRSSUR (DP) RATING. ##** NUMBR INDICATS OPTIONAL DSIGN PRSSUR (DP) RATING. Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-12
2-WID UNITS 62 1/4 (1581) 65 1/4 (1657) 59 1/2 (1511) 58 3/4 (1492) 22 13/16 (579)[2] 66 1/4 (1683) 69 1/4 (1759) 63 1/2 (1613) 62 3/4 (1594) 24 13/16 (630)[2] M.O. BRICKMOULD 46 1/4 (1175) 54 1/4 (1378) 70 1/4 (1784) 78 1/4 (1988) 86 1/4 (2191) M.O. ADAMS/FLAT CASING 49 1/4 (1251) 57 1/4 (1454) 73 1/4 (1861) 81 1/4 (2064) 89 1/4 (2267) ROUGH OPNING 43 1/2 (1105) 51 1/2 (1308) 67 1/2 (1715) 75 1/2 (1918) 83 1/2 (2121) FRAM SIZ 42 3/4 (1086) 50 3/4 (1289) 66 3/4 (1695) 74 3/4 (1899) 82 3/4 (2102) DAYLIGHT OPNING 14 13/16 (376)[2] 18 13/16 (478)[2] 26 13/16 (681)[2] 30 13/16 (782)[2] 34 13/16 (884)[2] 34 11/16 (881) 36 3/16 (919) 32 3/4 (832) 32 (813) 11 1/16 (281)[2] 38 11/16 (983) 40 3/16 (1021) 36 3/4 (933) 36 (914) 13 1/16 (332)[2] 40 3/4 (1035) 40 (1016) 15 1/16 (383)[2] 44 3/4 (1137) 44 (1118) 17 1/16 (433)[2] 68 3/4 (1746) 68 (1727) 29 1/16 (738)[2] 64 3/4 (1645) 64 (1626) 27 1/16 (687)[2] 60 3/4 (1543) 60 (1524) 25 1/16 (637)[2] 56 3/4 (1441) 56 (1422) 23 1/16 (586)[2] 52 3/4 (1340) 52 (1321) 21 1/16 (535)[2] 48 3/4 (1238) 48 (1219) 19 1/16 (484)[2] 42 11/16 (1084) 44 3/16 (1122) 46 11/16 (1186) 48 3/16 (1224) WD2132-2 WD2532-2 WD2932-2 WD3132-2 WD3332-2 WD3732-2 WD4132-2 WD2136-2 WD2536-2 WD2936-2 WD3136-2 WD3336-2 WD3736-2 WD4136-2 WD2140-2 WD2540-2 WD2940-2 WD3140-2 WD3340-2 WD3740-2 WD4140-2 WD2144-2 WD2544-2 WD2944-2 WD3144-2 WD3344-2 WD3744-2 WD4144-2 70 11/16 (1795) 72 3/16 (1834) 66 11/16 (1694) 68 3/16 (1732) 62 11/16 (1592) 64 3/16 (1630) 58 11/16 (1491) 60 3/16 (1529) 54 11/16 (1389) 56 3/16 (1427) 50 11/16 (1287) 52 3/16 (1326) WD2148-2 WD2548-2 WD2948-2 WD3148-2 WD3348-2 WD3748-2 WD4148-2 WD2152-2 WD2552-2 WD2952-2 WD3152-2 WD3352-2 WD3752-2 WD4152-2 WD2156-2 WD2556-2 WD2956-2 WD3156-2 WD3356-2 WD3756-2 WD4156-2 WD2160-2 WD2560-2 WD2960-2 WD3160-2 WD3360-2 WD3760-2 WD4160-2 WD2164-2 WD2564-2 WD2964-2 WD3164-2 WD3364-2 WD3764-2 WD4164-2 WD2168-2 WD2568-2 WD2968-2 WD3168-2 WD3368-2 WD3768-2 WD4168-2 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL: 1/8 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-13
2-WID UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 46 1/4 (1175) 54 1/4 (1378) 62 1/4 (1581) 66 1/4 (1683) 70 1/4 (1784) 78 1/4 (1988) 86 1/4 (2191) 49 1/4 (1251) 57 1/4 (1454) 65 1/4 (1657) 69 1/4 (1759) 73 1/4 (1861) 81 1/4 (2064) 89 1/4 (2267) 43 1/2 (1105) 51 1/2 (1308) 59 1/2 (1511) 63 1/2 (1613) 67 1/2 (1715) 75 1/2 (1918) 83 1/2 (2121) 42 3/4 (1086) 50 3/4 (1289) 58 3/4 (1492) 62 3/4 (1594) 66 3/4 (1695) 74 3/4 (1899) 82 3/4 (2102) 14 13/16 (376)[2] 18 13/16 (478)[2] 22 13/16 (579)[2] 24 13/16 (630)[2] 26 13/16 (681)[2] 30 13/16 (782)[2] 34 13/16 (884)[2] 82 11/16 (2100) 84 3/16 (2138) 80 3/4 (2051) 80 (2032) 35 1/16 (891)[2] 78 11/16 (1999) 80 3/16 (2037) 76 3/4 (1949) 76 (1930) 33 1/16 (840)[2] 74 11/16 (1897) 76 3/16 (1935) 72 3/4 (1848) 72 (1829) 31 1/16 (789)[2] WD2172-2 WD2572-2 WD2972-2 WD3172-2 WD3372-2 WD3772-2 WD4172-2 WD2176-2 WD2576-2 WD2976-2 WD3176-2 WD3376-2 WD3776-2 WD4176-2 WD2180-2 WD2580-2 WD2980-2 WD3180-2 WD3380-2 WD3780-2 WD4180-2 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL: 1/8 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-14
2-WID UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 94 1/4 (2394) 97 1/4 (2470) 91 1/2 (2324) 90 3/4 (2305) 38 13/16 (986)[2] M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 94 1/4 (2394) 97 1/4 (2470) 91 1/2 (2324) 90 3/4 (2305) 38 13/16 (986)[2] 34 11/16 (881) 36 3/16 (919) 32 3/4 (832) 32 (813) 11 1/16 (281)[2] 38 11/16 (983) 40 3/16 (1021) 42 11/16 (1084) 44 3/16 (1122) WD4532-2 WD4536-2 WD4540-2 WD4572-2 WD4544-2 WD4576-2 WD4580-2 WD4548-2 WD4552-2 WD4556-2 60 3/4 (1543) 60 (1524) 25 1/16 (637)[2] 56 3/4 (1441) 56 (1422) 23 1/16 (586)[2] 52 3/4 (1340) 52 (1321) 21 1/16 (535)[2] 36 3/4 (933) 36 (914) 13 1/16 (332)[2] 40 3/4 (1035) 40 (1016) 15 1/16 (383)[2] 74 11/16 (1897) 76 3/16 (1935) 72 3/4 (1848) 72 (1829) 31 1/16 (789)[2] 78 11/16 (1999) 80 3/16 (2037) 76 3/4 (1949) 76 (1930) 33 1/16 (840)[2] 44 3/4 (1137) 44 (1118) 17 1/16 (433)[2] 48 3/4 (1238) 48 (1219) 19 1/16 (484)[2] 82 11/16 (2100) 84 3/16 (2138) 80 3/4 (2051) 80 (2032) 35 1/16 (891)[2] WD4560-2 64 3/4 (1645) 64 (1626) 27 1/16 (687)[2] WD4564-2 70 11/16 (1795) 72 3/16 (1834) 68 3/4 (1746) 68 (1727) 29 1/16 (738)[2] 66 11/16 (1694) 68 3/16 (1732) 62 11/16 (1592) 64 3/16 (1630) 46 11/16 (1186) 48 3/16 (1224) 50 11/16 (1287) 52 3/16 (1326) 58 11/16 (1491) 60 3/16 (1529) 54 11/16 (1389) 56 3/16 (1427) WD4568-2 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL: 1/8 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-15
LVATION NOTS DOUBL-HUNG PICTUR LVATION DRAWINGS UTILIZ A LIMITD NUMBR OF PROJCTD LINS TO PRODUC A RUDIMNTARY DRAWING INTNDD TO B USD IN A SMALL GRAPHICAL SCAL. LVATIONS AR VIWD PRPNDICULAR FROM TH XTRIOR OF TH STRUCTUR. IF MOR DIMNSIONS AR NDD, US TH SCTION DRAWINGS FOR MOR COMPLT DPICTIONS. M.O. Brickmould M.O. Adams/Flat Casing Rough Opening Frame Size Daylight Opening 36 1/2 (927) 39 1/2 (1003) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) Masonry Openings for Brickmould, Flat & Adams Casing. Vertical measurements include sillnose. (Subtract 1/2 from Masonry Opening for Unit Size) 38 11/16 (983) 40 3/16 (1021) 36 3/4 (933) 36 (914) 28 5/16 (719) DAYLIGHT OPNING OUTSID OF XTRIOR TRIM WDP3336 WDP INDICATS SITLIN X WOOD DH PICTUR TH FIRST TWO NUMBRS INDICAT TH UNIT WIDTH BOOK COD TH LAST TWO NUMBRS INDICAT TH UNIT HIGHT GNRAL DOUBL-HUNG PICTUR NOTS LVATION SYMBOL LGND: 1. ALL UNITS SHOWN AR AVAILABL AS OPRATORS ONLY. 2. UNIT LVATIONS AR SHOWN WITH BRICKMOULD & SILL NOS. 3. DIMNSIONAL VALUS IN PARNTHSS AR MILLIMTR CONVRSIONS. MO MASONRY OPNING October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-16
PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 24 1/2 (645) 27 1/2 (699) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) 28 1/2 (724) 31 1/2 (800) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 1/2 (826) 35 1/2 (902) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 1/2 (876) 37 1/2 (953) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 1/2 (927) 39 1/2 (1003) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 1/2 (1029) 43 1/2 (1105) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 1/2 (1130) 47 1/2 (1207) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) WDP2132 WDP2532 WDP2932 WDP3132 WDP3332 WDP3732 WDP4132 WDP2136 WDP2536 WDP2936 WDP3136 WDP3336 WDP3736 WDP4136 WDP2140 WDP2540 WDP2940 WDP3140 WDP3340 WDP3740 WDP4140 WDP2144 WDP2544 WDP2944 WDP3144 WDP3344 WDP3744 WDP4144 WDP2148 WDP2548 WDP2948 WDP3148 WDP3348 WDP3748 WDP4148 WDP2152 WDP2552 WDP2952 WDP3152 WDP3352 WDP3752 WDP4152 58 11/16 (1491) 60 3/16 (1529) 56 3/4 (1441) 56 (1422) 48 5/16 (1227) 54 11/16 (1389) 56 3/16 (1427) 52 3/4 (1340) 52 (1321) 44 5/16 (1126) 50 11/16 (1287) 52 3/16 (1326) 48 3/4 (1238) 48 (1219) 40 5/16 (1024) 46 11/16 (1186) 48 3/16 (1224) 44 3/4 (1137) 44 (1118) 36 5/16 (922) 42 11/16 (1084) 44 3/16 (1122) 40 3/4 (1035) 40 (1016) 32 5/16 (821) 38 11/16 (983) 40 3/16 (1021) 36 3/4 (933) 36 (914) 28 5/16 (719) 34 11/16 (881) 36 3/16 (919) 32 3/4 (832) 32 (813) 24 5/16 (618) WDP2156 WDP2556 WDP2956 WDP3156 WDP3356 WDP3756 WDP4156 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-17
PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 24 1/2 (645) 27 1/2 (699) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) 28 1/2 (724) 31 1/2 (800) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 1/2 (826) 35 1/2 (902) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 1/2 (876) 37 1/2 (953) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 1/2 (927) 39 1/2 (1003) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 1/2 (1029) 43 1/2 (1105) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 1/2 (1130) 47 1/2 (1207) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) 60 3/4 (1543) 60 (1524) WDP2160 WDP2560 WDP2960 WDP3160 WDP3360 WDP3760 WDP4160 64 3/4 (1645) 64 (1626) WDP2164 WDP2564 WDP2964 WDP3164 WDP3364 WDP3764 WDP4164 68 3/4 (1746) 68 (1727) WDP2168 WDP2568 WDP2968 WDP3168 WDP3368 WDP3768 WDP4168 72 3/4 (1848) 72 (1829) WDP2172 WDP2572 WDP2972 WDP3172 WDP3372 WDP3772 WDP4172 78 11/16 (1999) 80 3/16 (2037) 76 3/4 (1949) 76 (1930) 68 5/16 (1735) 74 11/16 (1897) 76 3/16 (1935) 64 5/16 (1634) 70 11/16 (1795) 72 3/16 (1834) 60 5/16 (1532) 66 11/16 (1694) 68 3/16 (1732) 56 5/16 (1430) 62 11/16 (1592) 64 3/16 (1630) 52 5/16 (1329) WDP2176 WDP2576 WDP2976 WDP3176 WDP3376 WDP3776 WDP4176 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-18
PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 24 1/2 (645) 27 1/2 (699) 22 1/8 (562) 21 3/8 (543) 14 13/16 (376) 28 1/2 (724) 31 1/2 (800) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 1/2 (826) 35 1/2 (902) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 1/2 (876) 37 1/2 (953) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 1/2 (927) 39 1/2 (1003) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 1/2 (1029) 43 1/2 (1105) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 1/2 (1130) 47 1/2 (1207) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) 80 3/4 (2051) 80 (2032) WDP2180 WDP2580 WDP2980 WDP3180 WDP3380 WDP3780 WDP4180 88 3/4 (2254) 88 (2235) WDP2188 WDP2588 WDP2988 WDP3188 WDP3388 WDP3788 WDP4188 94 11/16 (2405) 96 3/16 (2443) 92 3/4 (2356) 92 (2337) 84 5/16 (2142) 90 11/16 (2303) 92 3/16 (2342) 80 5/16 (2040) 82 11/16 (2100) 84 3/16 (2138) 72 5/16 (1837) WDP2192 WDP2592 WDP2992 WDP3192 WDP3392 WDP3792 WDP4192 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-19
PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 1/2 (1232) 51 1/2 (1308) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) 52 1/2 (1334) 55 1/2 (1410) 50 1/8 (1273) 49 3/8 (1254) 42 13/16 (1087) 56 1/2 (1435) 59 1/2 (1511) 54 1/8 (1375) 53 3/8 (1356) 46 13/16 (1189) 64 1/2 (1638) 67 1/2 (1715) 62 1/8 (1578) 61 3/8 (1559) 54 13/16 (1392) WDP4532 WDP4932 WDP5332 WDP6132 WDP4536 WDP4936 WDP5336 WDP6136 WDP4540 WDP4940 WDP5340 WDP6140 WDP4544 WDP4944 WDP5344 WDP6144 WDP4548 WDP4948 WDP5348 WDP6148 WDP4532 WDP4952 WDP5352 WDP6152 58 11/16 (1491) 60 3/16 (1529) 56 3/4 (1441) 56 (1422) 48 5/16 (1227) 54 11/16 (1389) 56 3/16 (1427) 52 3/4 (1340) 52 (1321) 44 5/16 (1126) 50 11/16 (1287) 52 3/16 (1326) 48 3/4 (1238) 48 (1219) 40 5/16 (1024) 46 11/16 (1186) 48 3/16 (1224) 44 3/4 (1137) 44 (1118) 36 5/16 (922) 42 11/16 (1084) 44 3/16 (1122) 40 3/4 (1035) 40 (1016) 32 5/16 (821) 38 11/16 (983) 40 3/16 (1021) 36 3/4 (933) 36 (914) 28 5/16 (719) 34 11/16 (881) 36 3/16 (919) 32 3/4 (832) 32 (813) 24 5/16 (618) WDP4556 WDP4956 WDP5356 WDP6156 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-20
PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 1/2 (1232) 51 1/2 (1308) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) 52 1/2 (1334) 55 1/2 (1410) 50 1/8 (1273) 49 3/8 (1254) 42 13/16 (1087) 56 1/2 (1435) 59 1/2 (1511) 54 1/8 (1375) 53 3/8 (1356) 46 13/16 (1189) 64 1/2 (1638) 67 1/2 (1715) 62 1/8 (1578) 61 3/8 (1559) 54 13/16 (1392) 60 3/4 (1543) 60 (1524) WDP4560 WDP4960 WDP5360 WDP6160 64 3/4 (1645) 64 (1626) WDP4564 WDP4964 WDP5364 WDP6164 68 3/4 (1746) 68 (1727) WDP4568 WDP4968 WDP5368 WDP6168 72 3/4 (1848) 72 (1829) WDP4572 WDP4972 WDP5372 WDP6172 78 11/16 (1999) 80 3/16 (2037) 76 3/4 (1949) 76 (1930) 68 5/16 (1735) 74 11/16 (1897) 76 3/16 (1935) 64 5/16 (1634) 70 11/16 (1795) 72 3/16 (1834) 60 5/16 (1532) 66 11/16 (1694) 68 3/16 (1732) 56 5/16 (1430) 62 11/16 (1592) 64 3/16 (1630) 52 5/16 (1329) WDP4576 WDP4976 WDP5376 WDP6176 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-21
PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 1/2 (1232) 51 1/2 (1308) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) 52 1/2 (1334) 55 1/2 (1410) 50 1/8 (1273) 49 3/8 (1254) 42 13/16 (1087) 56 1/2 (1435) 59 1/2 (1511) 54 1/8 (1375) 53 3/8 (1356) 46 13/16 (1189) 64 1/2 (1638) 67 1/2 (1715) 62 1/8 (1578) 61 3/8 (1559) 54 13/16 (1392) 80 3/4 (2051) 80 (2032) WDP4580 WDP4980 WDP5380 WDP6180 88 3/4 (2254) 88 (2235) WDP4588 94 11/16 (2405) 96 3/16 (2443) 92 3/4 (2356) 92 (2337) 84 5/16 (2142) 90 11/16 (2303) 92 3/16 (2342) 80 5/16 (2040) 82 11/16 (2100) 84 3/16 (2138) 72 5/16 (1837) WDP4592 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-22
PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 72 1/2 (1842) 75 1/2 (1918) 70 1/8 (1781) 69 3/8 (1762) 62 13/16 (1595) 80 1/2 (2045) 83 1/2 (2121) 78 1/8 (1984) 77 3/8 (1965) 70 13/16 (1799) WDP6932 WDP7732 WDP6936 WDP7736 WDP6940 WDP7740 WDP6944 WDP7744 WDP6948 WDP7748 WDP6952 WDP7752 58 11/16 (1491) 60 3/16 (1529) 56 3/4 (1441) 56 (1422) 48 5/16 (1227) 54 11/16 (1389) 56 3/16 (1427) 52 3/4 (1340) 52 (1321) 44 5/16 (1126) 50 11/16 (1287) 52 3/16 (1326) 48 3/4 (1238) 48 (1219) 40 5/16 (1024) 46 11/16 (1186) 48 3/16 (1224) 44 3/4 (1137) 44 (1118) 36 5/16 (922) 42 11/16 (1084) 44 3/16 (1122) 40 3/4 (1035) 40 (1016) 32 5/16 (821) 38 11/16 (983) 40 3/16 (1021) 36 3/4 (933) 36 (914) 28 5/16 (719) 34 11/16 (881) 36 3/16 (919) 32 3/4 (832) 32 (813) 24 5/16 (618) WDP6956 WDP7756 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-23
PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 72 1/2 (1842) 75 1/2 (1918) 70 1/8 (1781) 69 3/8 (1762) 62 13/16 (1595) 80 1/2 (2045) 83 1/2 (2121) 78 1/8 (1984) 77 3/8 (1965) 70 13/16 (1799) WDP6960 WDP7760 64 3/4 (1645) 64 (1626) 60 3/4 (1543) 60 (1524) WDP6964 WDP7764 68 3/4 (1746) 68 (1727) WDP6968 WDP7768 72 3/4 (1848) 72 (1829) WDP6972 WDP7772 78 11/16 (1999) 80 3/16 (2037) 76 3/4 (1949) 76 (1930) 68 5/16 (1735) 74 11/16 (1897) 76 3/16 (1935) 64 5/16 (1634) 70 11/16 (1795) 72 3/16 (1834) 60 5/16 (1532) 66 11/16 (1694) 68 3/16 (1732) 56 5/16 (1430) 62 11/16 (1592) 64 3/16 (1630) 52 5/16 (1329) WDP6976 WDP7776 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-24
PICTUR UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 72 1/2 (1842) 75 1/2 (1918) 70 1/8 (1781) 69 3/8 (1762) 62 13/16 (1595) 80 1/2 (2045) 83 1/2 (2121) 78 1/8 (1984) 77 3/8 (1965) 70 13/16 (1799) 82 11/16 (2100) 84 3/16 (2138) 80 3/4 (2051) 80 (2032) 72 5/16 (1837) WDP6980 WDP7780 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-25
PICTUR UNITS WITH 16 FLANKRS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 99 1/4 (2521) 102 1/4 (2597) 96 7/8 (2461) 96 1/8 (2442) 14 13/16 (376)[2] 46 13/16 (1189) 107 1/4 (2724) 110 1/4 (2800) 104 7/8 (2664) 104 1/8 (2645) 14 13/16 (376)[2] 54 13/16 (1392) 66 11/16 (1694) 68 3/16 (1732) 64 3/4 (1645) 64 (1626) 27 1/16 (687)[2] 56 5/16 (1430) 58 11/16 (1491) 60 3/16 (1529) 56 3/4 (1441) 56 (1422) 23 1/16 (586)[2] 48 5/16 (1227) 54 11/16 (1389) 56 3/16 (1427) 52 3/4 (1340) 52 (1321) 21 1/16 (535)[2] 44 5/16 (1126) WD5352-16 WD6152-16 WD5356-16 WD6156-16 WD5364-16 WD6164-16 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/8 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-26
PICTUR UNITS WITH 20 FLANKRS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 107 1/4 (2724) 110 1/4 (2800) 104 7/8 (2664) 104 1/8 (2645) 18 13/16 (478)[2] 54 13/16 (1392) 115 1/4 (2927) 118 1/4 (3004) 112 7/8 (2867) 112 1/8 (2848) 18 13/16 (478)[2] 62 13/16 (1595) 54 11/16 (1389) 56 3/16 (1427) 52 3/4 (1340) 52 (1321) 21 1/16 (535)[2] 44 5/16 (1126) WD6152-20 WD6952-20 66 11/16 (1694) 68 3/16 (1732) 64 3/4 (1645) 64 (1626) 27 1/16 (687)[2] 56 5/16 (1430) 58 11/16 (1491) 60 3/16 (1529) 56 3/4 (1441) 56 (1422) 23 1/16 (586)[2] 48 5/16 (1227) WD6156-20 WD6956-20 WD6164-20 WD6964-20 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/8 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-27
GNRAL INFORMATION SCTOR TOP SINGL-HUNG UNITS DIMNSIONAL WINDOWS Wood sector top single-hung windows may be specified as dimensional by adjusting the desired rough opening width or height in 1/4 increments from standard. Wood sector top single-hung windows feature stationary (fixed) upper sash and an operating lower sash. Counterbalancing is achieved with block and tackle spring extension systems hidden in weatherable PVC jambliners. Operating units are supplied with cam-type sash locks installed. Die-cast lower sash lifts supplied for field installation are an option. Recessed sash retainers provide simple sash installation and removal. There are several hardware finish options. Refer to the Specifications for available finish options. SITLIN X SCTIOR TOP SINGL-HUNG WINDOWS utilize some of the same options as SITLIN X DOUBL-HUNG. These options have not been repeated here in this sub-section. See the SITLIN X DOUBL-HUNG section for: Trim Options (all wood exterior trim is available as radius trim) and Jamb xtender Options. October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-28
HANDING & OPRATION SCTOR TOP SINGL-HUNG UNITS SINGL-HUNG OPRATION: When the sash are locked at the check rails the sash are closed and sealed in the sash opening of the frame. When the sash are unlocked the lower sash travels vertically to any position desired. The upper sash is fixed. SASH TILTING FOR WASHING The Custom Wood Single-Hung window will allow the lower sash to be tilted or removed for easy cleaning. October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-29
LVATION NOTS SCTOR TOP SINGL-HUNG UNITS LVATION DRAWINGS UTILIZ A LIMITD NUMBR OF PROJCTD LINS TO PRODUC A RUDIMNTARY DRAWING INTNDD TO B USD IN A SMALL GRAPHICAL SCAL. LVATIONS AR VIWD PRPNDICULAR FROM TH XTRIOR OF TH STRUCTUR. IF MOR DIMNSIONS AR NDD, US TH SCTION DRAWINGS FOR MOR COMPLT DPICTIONS. M.O. Brickmould M.O. Adams/Flat Casing Rough Opening Frame Size Daylight Opening 28 1/2 (724) 31 1/2 (800) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) Masonry Openings for Brickmould, Flat & Adams Casing. Vertical measurements include sillnose. (Subtract 1/2 from Masonry Opening for Unit Size) 58 11/16 (1491) 60 3/16 (1529) 56 3/4 (1441) 56 (1422) 23 1/16 (586) 23 5/16 (592) DAYLIGHT OPNING OUTSID OF XTRIOR TRIM WDS2556 WDS INDICATS SITLIN X WOOD SCTOR TOP SINGL-HUNG TH FIRST TWO NUMBRS INDICAT TH UNIT WIDTH BOOK COD TH LAST TWO NUMBRS INDICAT TH UNIT HIGHT GNRAL WOOD SINGL-HUNG NOTS LVATION SYMBOL LGND: 1. ALL UNITS SHOWN AR AVAILABL AS OPRATORS ONLY. 2. UNIT LVATIONS AR SHOWN WITH BRICKMOULD & SUBSILL. 3. ALL OPRATING SASH AR INSTALLD WITH VINYL JAMB LINRS AND OPRATD WITH AN INTRNAL BLOCK AND TACKL SPRING SYSTM. 4. DIMNSIONAL VALUS IN PARNTHSS AR MILLIMTR CONVRSIONS. MO MASONRY OPNING October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-30
SCTOR TOP UNITS - 1-WID M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 28 1/2 (724) 31 1/2 (800) 26 1/8 (664) 25 3/8 (645) 18 13/16 (478) 32 1/2 (826) 35 1/2 (902) 30 1/8 (765) 29 3/8 (670) 22 13/16 (579) 34 1/2 (876) 37 1/2 (953) 32 1/8 (816) 31 3/8 (797) 24 13/16 (630) 36 1/2 (927) 39 1/2 (1003) 34 1/8 (867) 33 3/8 (848) 26 13/16 (681) 40 1/2 (1029) 43 1/2 (1105) 38 1/8 (968) 37 3/8 (949) 30 13/16 (783) 44 1/2 (1130) 47 1/2 (1207) 42 1/8 (1070) 41 3/8 (1051) 34 13/16 (884) WDS2556 WDS2956 WDS3156 WDS3356 WDS3756 WDS4156 WDS2560 WDS2960 WDS3160 WDS3360 WDS3760 WDS4160 WDS2564 WDS2964 WDS3164 WDS3364 WDS3764 WDS4164 WDS2568 WDS2968 WDS3168 WDS3368 WDS3768 WDS4168 74 11/16 (1897) 76 3/16 (1935) 72 3/4 (1848) 72 (1829) 31 1/16 (789) 31 5/16 (795) 70 11/16 (1795) 72 3/16 (1834) 68 3/4 (1746) 68 (1727) 29 1/16 (738) 29 5/16 (745) 66 11/16 (1694) 68 3/16 (1732) 64 3/4 (1645) 64 (1626) 27 1/16 (687) 27 5/16 (694) 62 11/16 (1592) 64 3/16 (1630) 60 3/4 (1543) 60 (1524) 25 1/16 (637) 25 5/16 (643) 58 11/16 (1491) 60 3/16 (1529) 56 3/4 (1441) 56 (1422) 23 1/16 (586) 23 5/16 (592) WDS2572 WDS2972 WDS3172 WDS3372 WDS3772 WDS4172 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-31
SCTOR TOP UNITS - 1-WID M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 48 1/2 (1232) 51 1/2 (1308) 46 1/8 (1172) 45 3/8 (1153) 38 13/16 (986) WDS4556 WDS4560 WDS4564 WDS4568 74 11/16 (1897) 76 3/16 (1935) 72 3/4 (1848) 72 (1829) 31 1/16 (789) 31 5/16 (795) 70 11/16 (1795) 72 3/16 (1834) 68 3/4 (1746) 68 (1727) 29 1/16 (738) 29 5/16 (745) 66 11/16 (1694) 68 3/16 (1732) 64 3/4 (1645) 64 (1626) 27 1/16 (687) 27 5/16 (694) 62 11/16 (1592) 64 3/16 (1630) 60 3/4 (1543) 60 (1524) 25 1/16 (637) 25 5/16 (643) 58 11/16 (1491) 60 3/16 (1529) 56 3/4 (1441) 56 (1422) 23 1/16 (586) 23 5/16 (592) WDS4572 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/4 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-32
SCTOR TOP UNITS - 2-WID M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPNING FRAM SIZ DAYLIGHT OPNING 53 7/8 (1368) 56 7/8 (1445) 51 1/2 (1308) 50 3/4 (1289) 18 13/16 (478)[2] 61 7/8 (1572) 64 7/8 (1648) 59 1/2 (1511) 58 3/4 (1492) 22 13/16 (579)[2] 69 7/8 (1775) 72 7/8 (1851) 67 1/2 (1715) 66 3/4 (1695) 26 13/16 (681)[2] 77 7/8 (1978) 80 7/8 (2054) 75 1/2 (1918) 74 3/4 (1899) 30 13/16 (783)[2] WDS2556-2 WDS2956-2 WDS3356-2 WDS3756-2 WDS2560-2 WDS2960-2 WDS3360-2 WDS3760-2 WDS2564-2 WDS2964-2 WDS3364-2 WDS3764-2 WDS2568-2 WDS2968-2 WDS3368-2 WDS3768-2 74 11/16 (1897) 76 3/16 (1935) 72 3/4 (1848) 72 (1829) 31 1/16 (789) 31 5/16 (795) 70 11/16 (1795) 72 3/16 (1834) 68 3/4 (1746) 68 (1727) 29 1/16 (738) 29 5/16 (745) 66 11/16 (1694) 68 3/16 (1732) 64 3/4 (1645) 64 (1626) 27 1/16 (687) 27 5/16 (694) 62 11/16 (1592) 64 3/16 (1630) 60 3/4 (1524) 60 (1524) 25 1/16 (637) 25 5/16 (643) 58 11/16 (1491) 60 3/16 (1529) 56 3/4 (1441) 56 (1422) 23 1/16 (586) 23 5/16 (592) WDS2572-2 WDS2972-2 WDS3372-2 WDS3772-2 LVATION SYMBOL LGND: M.O. = MASONRY OPNING VALUS IN () AR IN MILLIMTR CONVRSIONS VALUS IN [] AR NUMBR OF DAYLIGHT OPNINGS PR UNIT Note: levations shown DO NOT have exterior trim. Subtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCAL 1/8 = 1 October 2007 JLD-WN reserves the right to change specifications without notice. Page 6-33