HYDRAULIC COPONENTS HYDROSTATIC TRANSISSIONS GEARBOXES - ACCESSORIES Via. L. Kig, 6-41122 ODENA (ITALY) Tel: +9 9 41 711 Fax: +9 9 41 729 / 9 41 7 INTERNET: http://www.hasatmp.it E-AIL: hasatmp@hasatmp.it HT / E / 4 / 211 / E Orbit otors (Spool Valve Distributor)
Cotets Geeral Iformatio... 4 Hydraulic otors Series... - 1 Hydraulic otors P Series... 14-2 Hydraulic otors R Series... - 4 Hydraulic otors with Tacho Coectio R...T Series... 44 Hydraulic otors RNA Series... 4 Hydraulic otors RFL Series... 46 Hydraulic otors with Dual Shaft RB Series... 47-49 Hydraulic otors PL Series... - 4 Hydraulic otors RL Series... - 8 Hydraulic otors PK Series... 9-62 Hydraulic otors RK Series... 6-66 Hydraulic otors RW Series... 67-76 Hydraulic otors H Series... 77-84 Hydraulic otors HW Series... 8-98 Hydraulic otors Special Features... 99 Hydraulic otors with Speed Sesor... - 1 Applicatio Calculatios... 2 - HT / E / 4 / 211 / E Pag.
GENERAL INFORATION: Orbit motors covert hydraulic eergy (pressure, oil flow) ito mechaical eergy (torque, speed). Hydraulic orbit motors operate o the priciple of a iteral gear (rotor) rotatig withi a fixed exteral gear (stator). The iteral gear trasmits the torque geerated by the applicatio of pressure from hydraulic oil fed ito motor which is the delivered via the motor's output shaft. Orbit motors have high startig torque ad costat output torque at wide speed rage. DISTIBUTOR VALVE, P, R, H, PL, RL, PK, RK, RW, HW series motors have spool valve: the distributor valve has bee itegrated with the output shaft. The carda shaft rotates distributor valve ad trasfers mechaical eergy from gerotor set to output shaft. The valve has hydrodyamic bearigs ad has ifiite life whe load ratigs are ot exceeded. GEARWHEEL SET There are two forms of gearwheel set: - Gerotor set have plai teeth. These types motors are suitable for log operatig periods at moderate pressures or short operatig periods at high pressures., P, PL ad PK series motors have gerotor set. - Roll-gerotor set have teeth fitted with rollers. The rollers reduce local stress ad the tagetial reactio forces o the rotor reducig frictio to a miimum. This gives log operatig life ad better efficiecy eve at cotiuous high pressures. Roll-gerotor sets are recommeded for operatio with thi oil ad for applicatios with cotiually reversig loads. R, RL, RK, H, RW ad HW series motors have roll-gerotor set. FEATURES: Stadard otor The stadard motor moutig flage is located as close to the output shaft as possible. This type of moutig supports the motor close to the shaft load. This moutig flage is also compatible with may stadard gear boxes. Wheel otor W moutig flage makes the motors possible to fit a wheel hub or a wich drum so that the radial load acts closer to motor bearigs. This gives the best utilizatio of the bearig capacity ad is a very compact solutio. Needle Bearig PN ad RN have a output shaft supported i eedle bearig. These types motors are suitable for operatig coditios such us frequet start ad stops, vibratio o the shaft, high static ad dyamic radial loads i short operatig terms. Low Leakage LL Series hydraulic motors are desiged to operate at the whole stadard rage of workig coditios (pressure drop ad frequecy of rotatio ), but with cosiderable decreased volumetric losses i the drai ports. This motors are suitable for hydraulic systems with series-coected motors with demads for low leakage. Low Speed LSV feature optimizes the motor for low-speed performace. otors with this valvig provide very Valve speed while maitaiig high torque. They are desiged to ru cotiuously at low speed (up to -1-1 mi ) at ormal pressure drop ad reduced flow. Optimal ru is guarateed at frequecy of rotatio from to mi. otors with this valvig have a icreased startig pressure ad are ot recommeded for usig at pressure drop less tha 4 bar. Free Ruig FR motors are with icreased clearace at all frictio parts, allowig the shaft to rotate more freely with less mechaical drag. The icreased clearace also improves lubricatio of the wear surfaces of gear set ad frictio parts. Additioal advatages of FR versio are prologig of the life of the hydraulic motors at high speeds, as well as the possibility to use them i systems with wide variatio of the loadig. FR Series motors are desiged to operate with high -1 speed /over tha mi / ad low pressure drop. Volumetric efficiecy may be reduced slightly. High Pressure Shaft Seal The high pressure shaft seals allow the motors to withstad high case pressures at high speeds without exteral drai lie. otors with Speed Sesor otors are available with itegrated iductive speed sesor. The output sigal is a stadardized voltage sigal that ca be used to cotrol the speed of a motor. The torque ad the radial load of the motor are ot affected by the istallatio of speed sesor. Pag. 4 HT / E / 4 / 211 / E
Hydraulic otors Series GENERAL APPLICATION» Coveyors» Textile machies» iig machiery» achie tools» Vetilators» Costructio plat equipmet ad access platforms etc. CONTENTS Specificatio data... 6 Fuctio diagrams... 7 9 Dimesios ad moutig.. 11 Shaft extesios... 12 Permissible shaft loads... 12 Order code... 1 OPTIONS» odel- Spool valve, gerotor» With or without flage» Side ad rear ports» Series with pressure valve(s)» Shafts- straight ad splied» etric ad BSPP ports» Speed sesorig;» Other special features ax. Displacemet, cm /rev [i /rev ax. Speed, [RP ax. Torque, [i-lb ax. Output, kw [ HP ax. Pressure Drop, bar [ PSI ax. Oil Flow, lpm [ GP i. Speed, [RP Pressure fluid O O Temperature rage, C [ F 2 Optimal Viscosity rage, mm /s [SUS Filtratio P Series with Itegrated Iteral Crossover Relief Valve A B, p= or bar [14 or 72 PSI A [. 244 : 4, [ 98 :,8 [1,2 [ 4, : [ 1 : 14 [ 2 [6.6 ieral based- HLP(DIN 124) or H(ISO 674/4) -4 14 [-4 284 7 [ 98 47 ISO code /16 (i. recommeded fluid filtratio of 2 micro) P Series with Itegrated Iteral Crossover Relief Valve B A, p= or bar [14 or 72 PSI A B B p bar 14 12 8 6 4 2 p PSI 1 Pressure Losses 2. 7. 12. 1 17. 22. Q, GP 4 6 7 8 9 Q, lpm A D Series with Itegrated Iteral Crossover Relief Valves B, p= or bar [14 or 72 PSI A B HT / E / 4 / 211 / E Pag.
otors SPECIFICATION DATA Type Displacemet, cm /rev. [ i /rev. ax. Speed, [RP ax. Torque [ 8 8,2 [. 19 244 1,2 [6 1, [1 12. 12,9 [.79 1 194 1,7 [1 2, [ [1.22 12 2,6 [2, [11 2 1,8 [1.9 6 79 4,2 [7,7 [6 4 4 [2.44 62 4,2 [7,7 [6 [. 4 4, [98,8 [1 ax. Output kw [ HP ax. Pressure Drop bar [ PSI Peak** 2,1 [187 1,8 [2.4 2,6 [.6 [1 14 [, [29 2,4 [.,2 [4. [1 14 [,1 [4 2,4 [.,2 [4. [1 14 [ 6,4 [68 2,4 [.,2 [4. [1 14 [ 6,6 [84 1,8 [2., [ 4. 82, [ 1 [16 8 [78 1,7 [2.48 2,1 [2.8 7 [1 9 [1 Peak** [29 [29 [29 [29 14 [ 12 [181 ax. Oil Flow 16 [4.2 [. [. [. [. [. lpm [ GP [. 2 [6.6 2 [6.6 2 [6.6 2 [6.6 2 [6.6 ax. Ilet Pressure 14 [ 14 [ 14 [ 14 [ 14 [ 14 [ bar [PSI 17 [24 17 [24 17 [24 17 [24 17 [24 17 [24 Peak** 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 ax. Retur Pressure - RP 14 [ 14 [ 14 [ 14 [ 14 [ 14 [ without Drai Lie or -4 RP [1 [1 [1 [1 [1 [1 ax. Pressure 4-8 RP [72 [72 [72 [72 [72 [72 i Drai Lie, >8 RP [29 [29 [29 - - - bar [PSI -max. RP 14 [ 14 [ 14 [ 14 [ 14 [ 14 [ ax. Retur Pressure 14 [ 14 [ 14 [ 14 [ 14 [ 14 [ with Drai Lie 17 [24 17 [24 17 [24 17 [24 17 [24 17 [24 bar [PSI Peak** 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 ax. Startig Pressure with Uloaded Shaft, bar [PSI 4 [6 4 [6 4 [6 4 [6 4 [6 4 [6 i. Startig Torque At max. press. drop,7 [6 [1,2 2,1 [19,4 [, [29,7 [ [ At max. press. drop 1, [9 1 [1,7 2,9 [26 4,8 [42 4,6 [4 4,8 [42 i. Speed***, [RP 4 2 Weight, kg [ lb 1,9 [4.2 2, [4.41 2,1 [4.6 2,2 [4.8 2, [.7 2, [.1 For "F" flage: +.441 [, F(S) P 2, [4.41 2,2 [4.8 2,1 [4.6 2, [.7 2,2 [4.8 2,4 [.29 2, [.7 2, [.1 2,4 [.29 2,6 [.7 2,6 [.7 2,8 [6.17 D 2,6 [.7 2,7 [.9 2,8 [6.17 2,9 [6.9, [6.61,2 [7. * Itermittet operatio: the permissible values may occur for max. % of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1 mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. Pag. 6 HT / E / 4 / 211 / E
otors FUNCTION DIAGRAS 8 Q=1.26 GP 2. GP 4 1.6 GP GP 8 2.11 12.17 GP GP 16 4.2 GP.28 12 1,4 kw p=14 bar PSI 7 1,2 1,,8,6 it. N=,2 kw, kw 1kW t=7% 1, kw 2, kw 2kW 1 bar 174 PSI bar 14 PSI 7 bar PSI,4 6% 2,2 % bar 72 PSI bar 44 PSI 2 7 12 1 17 22 2 RP 12, 17 2,4 2,2 2, Q=1.26 GP.8 GP 1. GP GP 2.6 GP 1.96 2, kw GP.28 kw 2 6.6 GP p=14 bar PSI 1 12 1,8 1,6 1,4 1,2 it. 1kW 2kW 1, kw 1 bar 174 PSI bar 14 PSI 7 2 1,,8,6,4,2, kw t=7% N=,2 kw 7% 6% % 7 bar PSI bar 72 PSI bar 44 PSI 4 6 8 14 16 18 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. HT / E / 4 / 211 / E Pag. 7
otors OTORS FUNCTION DIAGRAS GP Q=.79 GP 1.2 GP 2.64 1.96 GP.28 GP 2.6 GP 2,, 2, 2, it. 1kW 1, kw 2kW 2, kw kw p=14 bar PSI 1 bar 174 PSI bar 14 PSI 1 1, 1,, N=,2 kw, kw t=7% 7% 6% % 7 bar PSI bar 72 PSI bar 44 PSI 4 6 7 8 9 1 1 2 RP GP Q=.79 GP 1.2 GP 2.64 1.96 GP.28 GP 2.6 GP 6,, 4 4 2, 4, 4,,, 1kW 1, kw 2kW 2, kw kw p=14 bar PSI 1 bar 174 PSI bar 14 PSI 1 2, 2, 1, 1,,, kw N=,2 kw t=7% 7% 6% % 7 bar PSI bar 72 PSI bar 44 PSI 4 6 7 8 The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. RP Pag. 8 HT / E / 4 / 211 / E
otors OTORS FUNCTION DIAGRAS 4 6 7 Q=.79 GP 1.2 GP 2.64 GP GP 1.96.28 GP 2.6 GP 4 6 4 it. % 6% 6% t=7 % 7% kw 2, kw 2kW 1, kw p=1 bar 174 PSI bar 14 PSI 8 bar PSI 2 N=,2 kw, kw 1kW bar 72 PSI 1 bar 44 PSI 4 6 RP 6 GP Q=.79 1.2 GP GP 2.64 GP 1.96.28 GP 2.6 GP 4 4 2 it. t=7% N=,2 kw 1kW, kw 1, kw 7% 2kW 6% 6% % p=9 bar 1 PSI 7 bar PSI bar 72 PSI 1 bar 44 PSI 1 bar 2 PSI 4 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. HT / E / 4 / 211 / E Pag. 9
otors DIENSIONS AND OUNTING DATA, S, P, D Three Bolts out SH Shaft C Shaft CK Shaft Shaft Dim. See Page 12 F Oval out (2 Holes) max 6,7 [1.44 Flage Dim. See Page 11 L max L max max,4 [1. ø6±,2 [2.62±.78 Rear Ports L1 Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized -CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized -CW 4 [.17 Port A T Port B Port Dim. See Page 11 S Side Ports L max Port A Port B L1 P T (A,B) : 2xG/8 or 2x18x1, - 12 mm [.47 i depth : G1/8 or x1 - mm [.9 i depth P Side Ports D Side Ports 4 [.17 L max 4 [.17 L max Port A Port A Port B Port B P (A,B) L 1 1 L P (A,B) Type 8 12, 2 4 Type P 8 P 12, P P 2 P 4 P L, mm [i. 4 [ 4.94 6 [ 4.17 9 [ 4.291 114 [ 4.488 117, [ 4.626 121, [ 4.78 L, mm [i. 11 [ 4.28 117 [ 4.66 1 [ 4.724 12 [ 4.921 128, [.9 12, [.217 Type S 8 S 12, S S 2 S 4 S Type D 8 D 12, D D 2 D 4 D L, mm [i. [ 4.14 7 [ 4.21 1 [ 4.1 11 [ 4.28 118, [ 4.66 122, [ 4.82 L, mm [i. 14 [.276 16 [.4 19 [.472 144 [.669 147, [.87 11, [.96 L, 1 mm [i., [.18, [.217 8, [. 1, [.1 17 [.669 21 [.827 L, 1 mm [i., [.18, [.217 8, [. 1, [.1 17 [.669 21 [.827 P (A,B) For F Flage +, mm 2, [.98 mm [i Pag. HT / E / 4 / 211 / E
otors OUNTING Three Bolts out F Oval out (2 Holes) 4 o [.197 2xø9±,2 [.4±.78 ø4 [1.77, [.217 C ø6±,2 [2.62±.78 ø 1, 6 -, [ 1,24 -.2 97 [.819 8±,2 [.149±.78 -, -.2 ø6 [2,48 ø4±,2 [1.772±.78 7 [2.874 2±,2 [.79±.78 PORTS Rear Ports S Side Ports T P (A,B) 1,2±, [.98±.118 Port A Port B 4 [.17,4 [1.197 - +,2 -, 1 +.7 9.9 max L Port A T,±,1 [.41±.9,4±,1 [.21±.9 1,2±, [.98±.118 11,7±, [.461±.12 Port B P (A,B) max 64 [2.2 P Side Ports with Sigle Crossover Relief Valve D Side Ports with Dual Crossover Relief Valve max L max L 4 [.17 Port A 2, [.98 Port A +,2 -, 1 +.79 -.9,4 [1.197 T 69 [2.716 +,2 -, 1 +.7 9 -.9,4 [1.197 T [2.716 69 21,2±,1 [.8±.9 Port B P (A,B) max 64 [2.2 4,±, [1.87±.118 Port B P (A,B) max 64 [2.2 Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized -CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized -CW C P T (A,B) mm [i : x6-12 mm [.47 i depth : 2xG/8 or 2x18x1, - 12 mm [.47 i depth : G1/8 or x1 - mm [.9 i depth HT / E / 4 / 211 / E Pag. 11
SHAFT EXTENSIONS C - ø16 straight, Parallel key xx16 DIN 688 ax. Torque,9 [4 CK - ø14 straight, Parallel key xx16 DIN 688 ax. Torque [26 -, [.197-.12 ø16 +,6, +.24.19 [.6 ø17 [.669 1 8 -,1 [.79 1 -. ø 14 8 [. 7,1 -. ø17 [.669 1 6 -,1 [.6 1 -. - - - - - otors -, [.197 -.12 +,4 28 6 +,4 28 +,17 [1.2 mi 11 [.4 deep +,17 [1.2 mi 1 6 1 [.4 deep SH - ø16, Splied, B17x14 DIN 482 ax. Torque 4,4 [9 +2 +.79 14 [.1 ø 16,,11 [.649.4 ø17 [.669 mm [i +,4 28 +,17 [1.2 mi 1 6 1 [.4 deep PERISSIBLE SHAFT LOAD Pa max Prad lbs 4 6 =8 dan [18 lbs Prad dan 18 16 mm [.79 i P rad=16 dan [6 lbs The permissible radial shaft load [Prad is calculated from the distace [L betwee the poit of load applicatio ad the moutig surface: 6 14 P rad = X, [dan 61,+L [L i mm; L 8 mm 6 11 P rad =, [lbs X 2.42 + L [L i ich; L.1 i The drawig shows the permissible radial load whe L= mm [.79 i. 1 If the calculated shaft load exceeds the 8 permissible, a flexible couplig must be used. 4 4 6 8 14 16 18 RP Pag. 12 HT / E / 4 / 211 / E
otors ORDER CODE 1 2 4 6 7 8 9 Pos.1 - Adjustmet Optio omit - without valve P - Side ports with sigle crossover relief valve D - Side ports with dual crossover relief valve Pos.2 - outig Flage omit F - Three bolts mout - Oval mout, two holes Pos. - Port type (ot valid forp add versio) omit - Rear ports S - Side ports Pos.4 - Displacemet code 8 12. 2 4-8,2 cm /rev [. i /rev - 12,9 cm /rev [.79 i /rev -, cm /rev [1.22 i /rev - 1,8 cm /rev [1.9 i /rev - 4, cm /rev [2.44 i /rev -, cm /rev [. i /rev Pos. - Shaft Extesios * C VC CK SH - ø16 straight, Parallel key Axx16 DIN688 - ø16 straight, Parallel key Axx16 DIN688 with corrosio resistat bushig - ø14 straight, Parallel key xx16 DIN688 - ø16, splied, B17x14 DIN 482 Pos. 6 - Ports omit - BSPP (ISO 228) - etric (ISO 262) Pos. 7 - Lie to cotrol ** (see page ) /L - B A (left ruig) /R - A B (right ruig) Pos. 8 - Valve Rated Pressure *** / / - p= bar - p= bar Pos. 9 - Special Features (see page 99) Pos. - Desig Series omit - Factory specified NOTES: * The permissible output torque for shafts must ot be exceeded! ** For P optio useful oly. *** For P ad D optio useful oly. P add are available with ew crossover relief valves with improved characteristics. The ew valves allow easier pressure settig i more wide rage: from [72 PSI to 14 bar [ PSI. For more iformatio about P ad D - series 2 please cotact with "HANSA-TP". The hydraulic motors are magao - phosphatized as stadard. F - FLANGE (2 Holes) Order No for Flage:4844 14 2xø9±,2 [.4±.78, [.217 97 [.819 8±,2 [.149±.78 -, -.2 ø6 [2,48 F Flage is mouted to the motor with screws - 6x14. Tighteig Torque: -6 Nm. 7 [2.874 2±,2 [.79±.78 HT / E / 4 / 211 / E Pag. 1
Hydraulic otors P Series APPLICATION»»»» Coveyors Feedig mechaism of robots ad maipulators etal workig machies Textile machies» Agriculture machies» Food idustries» Grass cuttig machiery etc. CONTENTS Specificatio data...1 18 Fuctio diagrams...19 2 Dimesios ad moutig... 26 27 Wheel motor... 28 Shaft extesios... 29 Permissible shaft loads... Permissible shaft Seal Pressure... 1 Order code... 2 OPTIONS» odel- Spool valve, gerotor» Flage ad wheel mout» otor with eedle bearig» Side ad rear ports» Shafts- straight, splied ad tapered» Shaft seal for high ad low pressure» etric ad BSPP ports» Speed sesorig» Other special features GENERAL ax. Displacemet, ax. Speed, ax. Torque, ax. Output, ax. Pressure Drop, ax. Oil Flow, i. Speed, Pressure fluid Temperature rage, Optimal Viscosity rage, Filtratio cm /rev [i /rev [RP [ kw [HP bar [PSI lpm [GP [RP O C [ F O 2 mm /s [SUS 62,6 [ 8. 181 : [441 : 64 [6 12,8 [17.1 :14 [ :[17 [24 7 [ 19.8 ieral based- HLP(DIN 124) or H(ISO 674/4) -4 14 [-4 284 7 [ 98 47 ISO code /16 (i. recommeded fluid filtratio of 2 micro) Pressure drop bar [ PSI [14 14 [ Oil flow i drai lie Viscosity Oil flow i drai lie 2 mm /s [ SUS lpm [ GP [ 98 [ 164 [98 [164 2, [.66 1,8 [.476, [.92 2,8 [.74 p bar 2 1 p PSI 4 Pressure Losses 2 4 6 8 12 14 16 18 Q, GP 4 6 7 8 Q, lpm Pag. 14 HT / E / 4 / 211 / E
P otors SPECIFICATION DATA Specificatio Data for P... motors with C, CO, SH, K ad SA shafts. (ø28,6 sealig diameter) Type P 2 P 2 P 4 P P 8 P P 12 Displacemet, cm³/rev [ i³/rev 2 [ 1.2 2 [ 1.9 4 [ 2.44 49, [.2 79,2 [ 4.8 99 [ 6.4 12,8 [ 7. ax. Speed, 16 16 1 12 7 6 486 [RP 181 17 17 11 94 7 6 ax. Torque, [ 29 4, [ 8 6,2 [ 9,4 [ 8 1,1 [ 14 19, [ 17 2,7 [ 2 [ 4,7 [ 41 6,1 [ 4 8,2 [ 7 11,9 [ 19, [ 172 2,7 [ 2 29,8 [ 264 Peak** 6,7 [ 9 8,6 [ 76,7 [ 9 14, [ 128 22,4 [ 198 27, [ 24 6, [ 2 ax. Output 4, [ 6.,8 [ 7.8 8,4 [ 11.,1 [ 1.,2 [ 1.7, [ 14.1,2 [ 1.7 kw [ HP 6,1 [ 8.2 7,8 [. 11,6 [ 1. 12,2 [ 16.1 12, [ 16.8 12,8 [ 17.1 12 [ 16.1 ax. Pressure Drop [ 14 [14 1 [ 17 14 [ 14 [ 14 [ 14 [ bar [ PSI 14 [ 14 [ 1 [ 22 17 [ 24 17 [24 17 [24 17 [24 Peak** 22 [ 26 22 [26 22 [ 26 22 [ 26 22 [26 22 [26 22 [26 ax. Oil Flow 4 [. [ 1.2 6 [ 1.9 6 [1.9 6 [1.9 6 [1.9 6 [1.9 lpm [ GP 4 [ 11.9 [ 14. 7 [ 18. 7 [ 19.8 7 [ 19.8 7 [ 19.8 7 [ 19.8 ax. Ilet Pressure 17 [ 24 17 [24 17 [24 17 [24 17 [24 17 [24 17 [24 bar [ PSI [ 29 [29 [29 [29 [29 [29 [29 Peak** 22 [ 26 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 ax. Retur Pressure 17 [ 24 17 [24 17 [24 17 [24 17 [24 17 [24 17 [24 with Drai Lie [ 29 [29 [29 [29 [29 [29 [29 bar [ PSI Peak** 22 [ 26 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 ax. Startig Pressure with Uloaded Shaft, bar [ PSI [14 [14 [14 [14 [14 [14 9 [ 11 i. Startig Torque At max.press. drop, [ 26 4, [,4 [ 48 7,8 [ 69 1,2 [ 117 16,6 [ 147,7 [ 18 [ At max.press. drop 4,2 [ 7,6 [ 6,8 [ 6 [ 88 16,8 [ 149 21 [ 186 26,6 [ 26 i. Speed***, [RP 1 Weight, kg [ lb For rear ports +,4 [.992 P(F)(N) PW(N) PQ(N),6 [ 12., [ 11.7, [ 11.1,6 [12., [11.7, [11.1,7 [ 12.6,4 [ 11.9,1 [ 11.2,8 [ 12.8, [ 12.1,2 [ 11.,9 [ 1.2,6 [ 12.4, [ 11.7 6,1 [ 1.,8 [ 12.8, [ 12.1 6,2 [ 1. 7,9 [ 1,6 [ 12. * Itermittet operatio: the permissible values may occur for max. % of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. HT / E / 4 / 211 / E Pag. 1
P otors SPECIFICATION DATA (cotiued) Specificatio Data for P... motors with C, CO, SH, K ad SA shafts. (ø28,6 sealig diameter) Type Displacemet, cm³/rev [ i³/rev ax. Speed, [RP ax. Torque [ ax. Output kw [ HP ax. Pressure Drop bar [ PSI ax. Oil Flow lpm [ GP ax. Ilet Pressure bar [ PSI ax. Retur Pressure with Drai Lie bar [ PSI ax. Startig Pressure with Uloaded Shaft, bar [ PSI i. Startig Torque [ i. Speed***, [RP Weight, kg [ lb For rear ports +,4 [.992 Peak** Peak** Peak** Peak** At max.press. drop At max.press. drop P(F)(N) PW(N) PQ(N) P 16 18,4 [ 9.66 78 472 1, [ 277 7,8 [ 4 4,8 [ 88,1 [ 1. 12,1 [ 16.2 14 [ 17 [24 22 [26 6 [1.9 7 [ 19.8 17 [24 [29 22 [26 17 [24 [29 22 [26 8 [ 116 28,2 [ 2, [ 14 6,4 [ 14.1 6,1 [ 1.,8 [ 12.8 P P 2 P 1 P 4 198 [ 12.1 247, [ 1.1 16,8 [ 19. 96 [ 24.16 49 [.2 62,6 [ 8. 242 19 1 1 9 78 26 189 1 1 6,6 [ 24 8 [ 6 8 [ 6 6 [ 19 9 [ 42 44 [ 89 4,6 [ 4 8, [ 16 6 [ 496 9 [ 24 7 [ 4 64 [ 66 [ 487 [ 1. 12 [ 16.1 68, [ 66 7, [ 12 [ 16.1 8 [ 7,8 [ 7.9 9 [ 12.1 8,4 [ 76 4,6 [ 6.2 7,8 [. 78 [ 69, [ 4.7 7,2 [ 9. 7 82 [ 727, [ 4.4,6 [ 7. 14 [ 1 [ 16 9 [ 1 7 [ 1 6 [ 87 [ 8 17 [24 17 [24 14 [ 11 [ 166 9 [ 1 8 [ 116 22 [26 22 [26 22 [26 18 [ 26 1 [ 188 1 [ 174 6 [1.9 6 [1.9 6 [1.9 6 [1.9 6 [1.9 6 [1.9 7 [ 19.8 7 [ 19.8 7 [ 19.8 7 [ 19.8 7 [19.8 7 [19.8 17 [24 17 [24 17 [24 17 [24 14 [ 14 [ [29 [29 [29 [29 17 [ 24 17 [24 22 [26 22 [26 22 [26 22 [26 22 [ 26 22 [26 17 [24 17 [24 17 [24 17 [24 14 [ 14 [ [29 [29 [29 [29 17 [24 17 [24 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 7 [ 6 [ 87 [ 7 [7, [ 29,6 [ 297 4,4 [ 4 42,6 [ 77 4,2 [ 479 61,9 [ 48 4, [ 6,8 [ 9 6,6 [ 14.6 6, [ 1.9 6 [ 1.2 6,8 [ 1 6, [ 14. 6,2 [ 1.7 7,1 [ 1.6 6,8 [ 1 6, [ 14. 7,6 [ 16.8 7,2 [ 1.9 6,8 [ 1 P [7 6 [ 18 4 [ 478 8,9 [ 8,6 [ 19 8, [ 18. P 6 [7 41, [ 67 62 [ 48 9, [ 21.4 9,2 [. 9 [ 19.8 * Itermittet operatio: the permissible values may occur for max. % of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. Pag. 16 HT / E / 4 / 211 / E
P otors SPECIFICATION DATA (cotiued) Specificatio Data for P... motors with CB, KB, OB ad HB shafts. (ø sealig diameter) Type P 2 P 2 P 4 P P 8 P P 12 Displacemet, cm³/rev [ i³/rev 2 [ 1.2 2 [ 1.9 4 [ 2.44 49, [.2 79,2 [ 4.8 99 [ 6.4 12,8 [ 7. ax. Speed, 16 16 1 12 7 6 486 [RP 181 17 17 11 94 7 6 ax. Torque, [ 29 4, [ 8 6,2 [ 9,4 [ 8 1,1 [ 14 19, [ 17 2,7 [ 2 [ 4,7 [ 41 6,1 [ 4 8,2 [ 7 11,9 [ 19, [ 172 2,7 [ 2 29,8 [ 264 Peak** 6,7 [ 9 8,6 [ 76,7 [ 9 14, [ 128 22,4 [ 198 27, [ 24 6, [ 2 ax. Output 4, [ 6.,8 [ 7.8 8,4 [ 11.,1 [ 1.,2 [ 1.7, [ 14.1,2 [ 1.7 kw [ HP 6,1 [ 8.2 7,8 [. 11,6 [ 1. 12,2 [ 16.1 12, [ 16.8 12,8 [ 17.1 12 [ 16.1 ax. Pressure Drop [ 14 [14 1 [ 17 14 [ 14 [ 14 [ 14 [ bar [ PSI 14 [ 14 [ 1 [ 22 17 [ 24 17 [24 17 [24 17 [24 Peak** 22 [ 26 22 [26 22 [ 26 22 [ 26 22 [26 22 [26 22 [26 ax. Oil Flow 4 [. [ 1.2 6 [ 1.9 6 [1.9 6 [1.9 6 [1.9 6 [1.9 lpm [ GP 4 [11.9 [ 14. 7 [ 18. 7 [ 19.8 7 [ 19.8 7 [ 19.8 7 [ 19.8 ax. Ilet Pressure 17 [ 24 17 [24 17 [24 17 [24 17 [24 17 [24 17 [24 bar [ PSI [ 29 [29 [29 [29 [29 [29 [29 Peak** 22 [ 26 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 ax. Retur Pressure 17 [ 24 17 [24 17 [24 17 [24 17 [24 17 [24 17 [24 with Drai Lie [ 29 [29 [29 [29 [29 [29 [29 bar [ PSI Peak** 22 [ 26 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 ax. Startig Pressure with Uloaded Shaft, bar [ PSI [14 [14 [14 [14 [14 [14 9 [ 11 i. Startig Torque At max.press. drop, [ 26 4, [,4 [ 48 7,8 [ 69 1,2 [ 117 16,6 [ 147,7 [ 18 [ At max.press. drop 4,2 [ 7,6 [ 6,8 [ 6 [ 88 16,8 [ 149 21 [ 186 26,6 [ 26 i. Speed***, [RP 1 Weight, kg [ lb For rear ports +,4 [.992 P(F)...B,6 [ 12.,6 [12.,7 [ 12.6, 9[ 1 6[ 1.2 6, 2[ 1. 7 6, [ 1.9 * Itermittet operatio: the permissible values may occur for max. % of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. HT / E / 4 / 211 / E Pag. 17
P otors SPECIFICATION DATA (cotiued) Specificatio Data for P... motors with CB, KB, OB ad HB shafts. (ø sealig diameter) Type Displacemet, cm³/rev [ i³/rev ax. Speed, [RP ax. Torque [ Peak** ax. Output kw [ HP ax. Pressure Drop bar [ PSI Peak** ax. Oil Flow lpm [ GP ax. Ilet Pressure bar [ PSI Peak** ax. Retur Pressure with Drai Lie bar [ PSI Peak** ax. Startig Pressure with Uloaded Shaft, bar [ PSI i. Startig Torque At max.press. drop [ At max.press. drop i. Speed***, [RP Weight, kg [ lb P(F)...B For rear ports +,4 [.992 P 16 18,4 [ 9.66 78 472 1, [ 277 7,8 [ 4 4,8 [ 88,1 [ 1. 12,1 [ 16.2 14 [ 17 [24 22 [26 6 [1.9 7 [19.8 17 [24 [29 22 [26 17 [24 [29 22 [26 8 [ 116 28,2 [ 2, [ 14 6, [ 14. P 198 [ 12.1 78 6,6 [ 24 4,6 [ 4 [ 487 [ 1. 12 [ 16.1 14 [ 17 [24 22 [26 6 [1.9 7 [19.8 17 [24 [29 22 [26 17 [24 [29 22 [26 P 2 P 1 P 4 247, [1.1 16,8 [19. 96 [24.16 49 [.2 62,6 [ 8. 242 47 [ 416 8, [ 16 68, [ 66 9 [ 12.1 12 [ 16.1 19 26 48 [ 46 6 [ 496 8 [ 7 7,6 [.2 9 [ 12.1 1 189 [ 441 9 [ 24 8,4 [ 76 6,2 [ 8. 7,8 [. 1 1 9 [ 42 7 [ 4 78 [ 69, [ 4.7 7,2 [ 9. 7 9 1 44 [ 89 64 [ 66 82 [ 727, [ 4.4,6 [ 7. 14 [ 1 [ 174 9 [ 14 6 [ 87 [ 8 17 [24 14 [ 11 [ 167 9 [ 1 8 [ 116 22 [26 22 [ 26 18 [ 26 1 [ 188 1 [ 174 6 [1.9 6 [1.9 6 [1.9 6 [1.9 6 [1.9 7 [19.8 7 [19.8 7 [19.8 7 [19.8 7 [19.8 17 [24 17 [24 17 [24 14 [ 14 [ [29 [29 [29 17 [ 24 17 [24 22 [26 22 [26 22 [26 22 [ 26 22 [26 17 [24 17 [24 17 [24 14 [ 14 [ [29 [29 [29 17 [24 17 [24 22 [26 22 [26 22 [26 22 [26 22 [26 7 [ 6 [ 87 [ 7 [7, [ 29 42,8 [ 79 4 [4,8 46,8 [ 414 42,6 [ 77 4,2 [ 479 48 [61,9 6,8 [ 9 6, 7[ 14. 8 6,9 [ 1.2 7,2 [ 1.9 7,7 [ 17 P [7 6 [ 18 4 [ 478 9, [19.9 P 6 [7 41, [ 67 62 [ 48 9, 6[ 21. 2 * Itermittet operatio: the permissible values may occur for max. % of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. Pag. 18 HT / E / 4 / 211 / E
P otors P 2 FUNCTION DIAGRAS 4 4 2 1 4 2 1 it. Q= 1. GP 2.6 GP 1 4. GP. GP 2 6.6 GP 1kW. kw N=.2 kw 2kW GP 7.9 9.2 GP =7% t 6% 4 6 8 14 16 18 RP 4kW % 4.6 GP 6kW GP 4 11.9 p=14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI bar 4 PSI P 2 6 Q= 1. GP 2.6 GP 1 4. GP. GP 2 6.6 GP 7.9 GP 9.2 GP 4.6 GP 4 11.9 GP 1.2 GP 14. GP 6 p=14 bar PSI 4 4 2 4 it. N=. kw 1 kw 2kW 4kW 6kW 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 1 2 =78% t 6 bar 87 PSI 1 7% 4 6 8 14 16 18 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. 6% % bar 4 PSI HT / E / 4 / 211 / E Pag. 19
P otors P 4 FUNCTION DIAGRAS 7 7 6 6 4 4 2 1 8 7 6 4 2 1 it. Q= 1. GP 2.6 GP N=. kw. GP 1kW =78% t 7.9 GP 2kW 7% 7% 4kW 6% 4.6 GP 4 6 8 14 16 18 RP 6kW % 1.2 GP 6 1.9 GP 8kW kw 7 18. GP p=1 bar 22 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI bar 4 PSI P 1 12 Q= 1. GP 2.6 GP. GP GP 7.9 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 9 8 7 6 4 11 9 8 7 6 4 2 it. N=1 kw 2kW 4kW =7% t 6kW 7% 8kW 6% 12 kw kw % p=17 bar 24 PSI 16 bar 2 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 1 4 6 8 14 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. bar 4 PSI Pag. HT / E / 4 / 211 / E
P otors FUNCTION DIAGRAS P 8 18 Q= 1. GP 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP GP 7 18. 7 19.8 GP 16 14 8 6 4 18 16 14 12 8 6 4 it. % 6% 7% 4kW =7% t N=1 kw 2kW 12 kw kw 8kW 6kW p=17 bar 24 PSI 16 bar 2 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 2 bar 4 PSI 4 6 7 8 9 RP P 2 24 Q= 1. GP 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 18 16 14 8 6 4 22 18 16 14 12 8 6 4 it. % 6% 7% 7% =78% t N=1 kw 2kW 4kW 6kW 12 kw kw 8kW p=17 bar 24 PSI 16 bar 2 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 2 bar 4 PSI 4 6 7 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. HT / E / 4 / 211 / E Pag. 21
P otors FUNCTION DIAGRAS P 12 Q= 1. GP 2.6 GP GP. 7.9 GP 4.6 GP GP 1.2 6 1.9 GP GP 7 18. 7 19.8 GP 2 28 1 24 16 12 8 4 it. % 6% 7% N=1 kw 7% =78% t 2kW 4kW 6kW 8kW kw p=17 bar 24 PSI 16 bar 2 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI bar 4 PSI 4 6 RP P 16 6 GP Q= 1. GP 2.6. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP GP 7 18. 7 19.8 GP 6 28 24 16 8 2 28 24 16 12 8 it. % 6% 7% 7% =78% t N=1 kw 2kW 4kW 6kW 8kW kw 12 kw p=17 bar 24 PSI 16 bar 2 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 4 4 bar 4 PSI 1 2 4 4 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. Pag. 22 HT / E / 4 / 211 / E
P otors FUNCTION DIAGRAS 4 GP Q= 1. P 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 4 4 2 1 4 2 1 it. % 6% 7% 7% =77% t N=1 kw 2kW 4kW 6kW 8kW kw p=17 bar 24 PSI 16 bar 2 PSI 14 bar PSI 11 bar 167 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI bar 4 PSI 1 2 RP P 2 4 4 2 1 6 4 4 2 1 Q= 1. GP it. 2.6 GP. GP % 7.9 GP 6% N=1 kw =8% t 7% 7% 2kW 4.6 GP 4kW 1 2 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. 1.2 GP 6kW 6 1.9 GP 8kW 7 18. GP kw 7 19.8 GP p=17 bar 24 PSI 16 bar 2 PSI 14 bar PSI 12 bar 18 PSI bar 14 PSI 8 bar 12 PSI 6 bar 87 PSI bar 4 PSI HT / E / 4 / 211 / E Pag. 2
P otors FUNCTION DIAGRAS P 1 6 64 Q= 1. GP 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 4 4 2 1 6 48 4 2 24 16 8 it. % 6% 7% =7% t N=1 kw 6kW 4kW 8kW 2kW 2 7 12 1 17 22 2 RP p=16 bar 2 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 12 PSI 7 bar PSI bar 7 PSI bar 4 PSI P 4 6 6 6 Q= 1. GP 2.6 GP GP. 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 4 2 1 4 4 4 2 1 it. % 6% 7% N=1 kw 7% =8% t 2kW 4kW 6kW p=12 bar 18 PSI 1 bar 16 PSI 9 bar 18 PSI 8 bar 116 PSI 6 bar 94 PSI bar 8 PSI 4 bar 6 PSI bar 4 PSI 2 7 12 1 17 The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. RP Pag. 24 HT / E / 4 / 211 / E
P otors P FUNCTION DIAGRAS 7 6 6 4 4 2 1 7 7 6 6 4 4 2 1 Q= 1. GP 2.6 GP. GP N=,kW GP 7.9 1kW 8% 4.6 GP 2kW kw 7% 1.2 GP 4kW 7% 6 1.9 GP kw 6kW 6% % 6% 7 18. GP 7 19.8 GP 4 6 7 8 9 1 1 1 14 1 p=1 bar 16 PSI 9 bar 1 PSI 7 bar 9 PSI 6 bar 87 PSI 4 bar 6 PSI bar 4 PSI 1 bar 2 PSI RP P 6 6 6 7 6 6 GP Q= 1. 2.6 GP. GP GP 7.9 4.6 GP 1.2 GP 6 1.9 GP GP 7 18. 7 19.8 GP 4 4 2 1 4 4 2 1 N=,kW 1kW 8% 2kW 7% 4 6 7 8 9 1 1 The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. kw 7% 6% 4kW 6% kw % p=8 bar 116 PSI 7 bar PSI bar 8 PSI 4 bar 6 PSI bar 4 PSI 1 bar 2 PSI RP HT / E / 4 / 211 / E Pag. 2
P otors SA Shaft SH Shaft K Shaft C Shaft CO Shaft DIENSIONS AND OUNTING DATA SA Shaft SH Shaft K Shaft C Shaft CO Shaft max [2.16 max [2.16 Shaft Dim. See Page 29 max 49 [1.929 max 49 [1.929 L max 8±,1 [1.496±.9 Port A C Port B 74±, [2.91±.118 Flage Dim. See Page 27 P (A,B) P (A,B) C L max 44±,1 [1.72±.9 Port A 8±, [.149±.118 Port B L1 Port Dim. See Page 27 L1 T max ø91 [.4 E Rear ports max ø91 [.4 OB Shaft KB Shaft CB Shaft HB Shaft L max max 7 [2.76 max 68, [2.689 SB Shaft max 14 [.1 mm [i C P T (A, B) :4x8-1mm[.1 i depth : 2xG1/2 or 2x22x1, - 1 mm [.9 i depth : G1/4 or 14x1, - 12 mm [.47 i depth (plugged) Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized -CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized -CW Type L, mm [i Type L, mm [i Type L, mm [i Type L, mm [i L,mm 1 [i P(F) 2 P(F) 2 P(F) 4 P(F) P(F) 8 P(F) P(F) 12 P(F) 16 14, [.28 1, [.1 16, [.7 1, [. 19, [.49 142, [.9 14, [.7 1, [.91 PQ 2 PQ 2 PQ 4 PQ PQ 8 PQ PQ 12 PQ 16 14, [. 141, [.7 142, [.61 142, [.9 146, [.7 148, [.8 12, [.98 16, [6.16 P(F)E 2 P(F)E 2 P(F)E 4 P(F)E P(F)E 8 P(F)E P(F)E 12 P(F)E 16 11, [.96 12, [6. 14, [6.6 1, [6.2 17, [6.18 16, [6. 16, [6.42 168, [6.61 PQE 2 PQE 2 PQE 4 PQE PQE 8 PQE PQE 12 PQE 16 18, [6.22 19, [6.26 16, [6. 19, [6.28 16, [6.42 166, [6.4 169, [6.67 174, [6.8, 6, 7,4 6,67,67 1, 16,67 21, [.21 [.2 [.29 [.26 [.42 [.2 [.66 [.84 P(F) P(F) 2 P(F) 1 P(F) 4 P(F) P(F) 6 1, [6.12 162, [6.8 171, [6.7 182, [7.17 19, [7.7 21, [8.9 PQ PQ 2 PQ 1 PQ 4 PQ PQ 6 162, [6.8 168, [6.6 178, [7.1 188, [7.42 2, [7.9 219, [8.62 P(F)E P(F)E 2 P(F)E 1 P(F)E 4 P(F)E P(F)E 6 17, [6.81 18, [7.9 189, [7.44, [7.87 21, [8.9 2, [9.7 PQE PQE 2 PQE 1 PQE 4 PQE PQE 6 179, [7.7 186, [7.2 19, [7.7 6, [8.11 219, [8.64 26, [9.1 26,67 [1., [1.1 42,67 [1.68, [2. 66,6 [2.62 84, [.1 Pag. 26 HT / E / 4 / 211 / E
P otors 2xø1, +,4 [.2 +.16 Oval out (2 Holes) OUNTING 8±, [.1±.118 1 [.118 ø6,4±,2 [4.189±.79 ø82,±, [.248±.19 F - Oval out (4 Holes) ±,1 [2.16±.9 max 1 [.976 16 [.6 4 4xø1, +,4 [.2 +.16 ø6,4±,2 [4.189±.79 8±, [.1±.118 Q - Square out (4 Bolts) ±,1 [2.16±.9 ø82,±,1 [.2±.9 mi 1 deep [.9 4x 82 [.228 ø44,4±, [1.748±.19 1 [.118 ø82,±, [.248±.19 ±,1 [2.16±.9 max 1 [.976 16 [.6 82 [.228 max 1 [.976 2,±, [.98±.118 mm [i PORTS Side Ports E Rear Ports 18±,1 [.78±.9 ±, [.787±.118 C Port A ±, [.787±.118 max 1 [.976 ±,1 [2.16±.9 max L Port A [.787 ±,1 [2.16±.9 [. 197 2 [.984 Port B 18±,1 [.78±.9 Port B P (A,B) T P (A,B) T 1,9 [.47 ±, [.787±.118 ±, [.787±.118 28,8 [1.14 C P T (A, B) : 4x8-1 mm [.1 i depth : 2xG1/2 or 2x22x1, - 1 mm [.9 i depth : G1/4 or 14x1, - 12 mm [.47 i depth (plugged) Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized -CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized -CW HT / E / 4 / 211 / E Pag. 27
P otors DIENSIONS AND OUNTING DATA - PW W - Wheel out L max mi [.787 L1 4x ø79±,2 [.11±.79 P (A,B) ±,1 [.787±.9 18,±,1 [.728±.9 ø8 -,46 [.149-.18 Port A Port B 78±1 [.71±.9 7 +, [.27 +.196 6,4±,1 [2.74±.9 4±, [1.7±.196 18,±,1 [.728±.9 max 112,4 [4.42 Type PW 2 PW 2 PW 4 PW PW 8 PW PW 12 PW 16 PW PW 2 PW 1 PW 4 PW PW 6 L, mm [i 77, 78, 79, 78, 82, 8, 88, 9, 98,, 114, 12, 18, 16, [. [.7 [.1 [.9 [.2 [. [.48 [.66 [.88 [4.1 [4.1 [4.92 [.4 [6.14 L,mm 1 [i, 6, 7,4 6,67,67 1, 16,67 21, 26,67, 42,67, 66,6 84, [.21 [.2 [.29 [.26 [.42 [.2 [.66 [.84 [1. [1.1 [1.68 [2. [2.62 [.1 max [4.14 ±,1 [2.16±.9 ø86±,2 [.86±.79 T mm [i max [.97 Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized -CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized -CW P T (A, B) : 2xG1/2 or 2x22x1, - 1 mm [.9 i depth : G1/4 or 14x1, - 12 mm [.47 i depth (plugged) ø±,1 [4.±.9 PERISSIBLE SHAFT LOADS PWN PW The curves apply to a B bearig life of hours. 1. ax. radial shaft load 2. = RP. = RP P rad P rad dan lbs 4. =8 RP 16 14 8 6 6 2 1 Pa max=1 dan [ lbs Pa max= dan + - [ 44 lbs 1 2 4 P rad dan 16 14 8 6 P rad lbs 6 2 1 Pa max=1 dan [ lbs Pa max= dan + - [ 44 lbs 1 1. ax. radial shaft load 2. = RP. = RP 4. =8 RP 2 4 4 4 4 2 1 i 4 2 1 i 1 8 6 4 mm 1 8 6 4 mm Pag. 28 HT / E / 4 / 211 / E
SHAFT EXTENSIONS FOR P AND R OTORS C - ø2 straight, Parallel key A8x7x2 DIN 688 ax. Torque 4 [ CB - ø2 straight, Parallel key Ax8x4 DIN 688 ax. Torque 77 [681 -,6 [.94-.14 2 8 -, [ 1.2 8 -.11 ø2 +,1 +,2 +. +.1 [.984 7 2 -, [ 1.78 9 -.7 ø [1.78 ø2 +,18 +,2 +. +.1 [ 1.26 7 8 -,6 [.1 -.14 ø28,6 [1.124 8 mi 16 [.6 deep 4,2±, [1.7±.197 8 mi 16 [.6 deep +,4 6, -1, +.16 [2.224 -.9 CO - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 ax. Torque 4 [ 6,4 -, [.22 -.19 +,1 -,1 28,1 +.9 -.1 [1.6 ø28,6 [1.124 4,2±, [1.7±.197 SH - splied, BS 9 (SAE 6B) ax. Torque 4 [ 4 -,2 ø2,4 -.8 [1. SB - splied A2x22xH DIN 482 ax. Torque 4 [ ø22±, 1 [.866±.1 A-A ø2±,21 [.984±.8 ø [1.78 18, [.728 22±,4 [.866±.16 KB - tapered 1:, Parallel key B6x6x DIN 688 ax. Torque 77 [681 A A +,2 ø26 [ 1.24 9 +.7 6 +,2 6,2 -, [.246-.19 ø21,47±,7 [.84±.27 8 mi 16 [.6 deep ø28,6 [1.124 mi 26,4 [1.9 4,2±, [1.7±.197 ø2,2±, [.997±.12 A-A 6 -, [.26 -.11 1 9,1 1 -, [.71 +.9 ø±,1 [1.78±.88 8±,4 [2.28 ±.16 6±,7 1 [1.417±.27 [.12 1: A A 4 [.17 S=41 Tighteig torque ±1 ø4, [.177 x1, [.196 ø44 [1.72 K - tapered 1:, Parallel key Bxx14 DIN 688 ax. Torque 4 [4 A-A -, [.197 -.11 24±,4 [.94 ±.16 1: A, [.87 S= Tighteig torque ±1 OB - tapered 1:8 SAEJ 1, Parallel key "x 16 16 "x1¼" BS46 ax. Torque 77 [681 A-A 7,96 -,2 [.1 -.8 +,4 6, -1, +.16 [2.224 -.9 ±,6 [1.77±.26 ø4 [.17 A S=1 7/16" Tighteig torque ±1 max 1,4 [.66 ø28,6±,1 [1.124±.88 A x1, ø4, [.177 ø44 [1.72 +,16 -,.6 1 7 6 [.669 + -.24 ø [1.78 [.196 SA - splied, B2x22h9 DIN 482 ax. Torque 4 [4 HB - ø1¼" splied 14T, ANSI B92.1-1976 Norm ax. Torque 77 [681 ø [1.78 A +,1 4 -,29 +.122 [2.126 -.114 ø 1,7 -,2 [ 1.2 1 1- UNEF -. ø 1,77 8 mi 16 [.6 deep -, [ 1.2 9 -.1 ø28,6 [1.124 ø24, -,1 -.1 P + R otors [.964 8 mi 16 [.6 deep mm [i 26,4±1 [1.9±.9 4,2±, [1.7±.197 8 mi 16 [.6 deep 6 +2 [1.417 +.79 +,4 6, -1, +.16 [2.224 -.9 HT / E / 4 / 211 / E Pag. 29
P + R otors PERISSIBLE SHAFT LOADS FOR P AND R OTORS The permissible radial shaft load P rad depeds o the speed, RP, distace L from the poit of load to the moutig flage ad shaft versio. outig Flage Shaft Versio cylidrical - C, CO tapered - K, splied - SH Radial Shaft Load P rad,i mm 8 x 2, dan* 9+L Radial Shaft Load P rad,i ich 8 221 x,lbs* RP.74+L * < _ RP; max Prad=8 dan [18 lbs > _ RP; L < mm [2.2 i P AND R splied - HB cylidrical - CB 8 x 187 9+L, dan* 8 166 x,lbs* RP.74+L cylidrical - C, CO 8 x 2, dan* 1+L 8 221 x,lbs* RP.98+L Radial Shaft Load Prad for C, CO Shaft Extesios by L= mm [1.18 i (24 mm [.94 i) P rad dan 9 8 6 4 P rad lbs 16 8 4 P max= 1 dan [ lbs P max= dan [ 44 lbs L= [ 1.18 Oval out Prad 4 6 8 RP Square out L= 24 [.94 PN AND RN The curves apply to a B bearig life of hours. Prad dan Prad lbs 16 14 8 6 4 2 1 Pa max=1 dan [ lbs Pa max= dan [ 44 lbs + - 1 2 4 1. ax. radial shaft load 2. = RP. = RP 4. =8 RP 2 1-1 i 8 6 4 - mm Pag. HT / E / 4 / 211 / E
P + R otors AX. PERISSIBLE SHAFT SEAL PRESSURE FOR P AND R OTORS P/R...U1 motors with high pressure seal ad without drai coectio: The shaft seal pressure equals the average of iput pressure ad retur pressure. P/R...U motors with high pressure seal ad drai coectio: The shaft seal pressure equals the pressure i the drai lie. P = P iput +P seal 2 retur P/R...1 motors with low pressure seal or stadard shaft seal ad without drai coectio: The shaft seal pressure ever exceeds the pressure i the retur lie. P/R... motors with low pressure seal or stadard shaft seal ad with drai coectio: The shaft seal pressure equals the pressure i the drai lie. ax. retur pressure without drai lie or max. pressure i the drai lie P bar 1 P PSI 2 1 14 2 1 4 4 6 8, RP 1: Drawig for Low Pressure Seal 2: Drawig for Stadard Shaft Seal for "...B" shafts : Drawig for Stadard Shaft Seal ("D" Seal) 4: Drawig for High Pressure Seal ("U" Seal) - cotiuous operatios - itermittet operatios HT / E / 4 / 211 / E Pag. 1
P otors ORDER CODE P 1 2 4 6 7 8 9 Pos.1 - outig Flage omit - Oval mout, two holes F - Oval mout, four holes Q -Square mout, four bolts W - Wheel mout Pos.2 - Optio (eedle bearigs) omit - oe N - with eedle bearigs Pos. - Port type omit E - Side ports - Rear ports Pos.4 - Displacemet code 2* - 2, cm /rev [1.2 i /rev 2* - 2, cm /rev [1.9 i /rev 4* - 4, cm /rev [2.44 i /rev - 49, cm /rev [.2 i /rev 8-79,2 cm /rev [4.8 i /rev - 99, cm /rev [6.4 i /rev 12 16 2 1 4 6-12,8 cm /rev [7. i /rev - 18,4 cm /rev [9.66 i /rev - 198, cm /rev [12. i /rev - 247, cm /rev [1. i /rev - 16,8 cm /rev [19. i /rev - 96, cm /rev [24.16 i /rev - 49, cm /rev [. i /rev - 62,6 cm /rev [8. i /rev Pos. - Shaft Extesios **(see page 29) C VC CO VCO SH VSH K SA VSA CB KB SB OB HB - ø2 straight, Parallel key A8x7x2 DIN688 - ø2 straight, Parallel key A8x7x2 DIN688 with corrosio resistat bushig - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 with corrosio resistat bushig - ø2,2 splied BS 9 (SAE 6B) - ø2,2 splied BS 9 (SAE 6B) with corrosio resistat bushig - ø28,6 tapered 1:, Parallel key Bxx14 DIN688 - ø24, splied B 2x22 DIN 482 - ø24, splied B 2x22 DIN 482 with corrosio resistat bushig - ø2 straight, Parallel key Ax8x4 DIN688 - ø tapered 1:, Parallel key B6x6x DIN688 - splied A 2x22 DIN 482 - ø1¼" tapered1:8, Parallel key "x "x1¼" BS46 - ø1¼" splied 14T ANSI B92.1-1976 Pos. 6 - Shaft Seal Versio (see page 1) omit - Low pressure shaft seal or Stadard shaft seal for... B shaft D - Stadard shaft seal U - High pressure shaft seal (without check valves) Pos. 7 - Drai Port omit - with drai port 1 - without drai port Pos. 8 - Ports omit - BSPP (ISO 228) - etric (ISO 262) Pos. 9 - Special Features (see page 99) Pos. - Desig Series omit - Factory specified * Not with Low Pressure Seal ** The permissible output torque for shafts must ot be exceeded! NOTES: The followig combiatios are ot allowed: - Q flage with...b shafts; - W flage with...b shafts ore rear ports; - N optio with...b shafts, Low Pressure Seal or U optio; -...B shafts with D ad U shaft seals. The hydraulic motors are magao-phosphatized as stadard. Pag. 2 HT / E / 4 / 211 / E
Hydraulic otors R Series APPLICATION»»»» Coveyors Feedig mechaism of robots ad maipulators etal workig machies Textile machies» Agriculture machies» Food idustries» Grass cuttig machiery etc. CONTENTS Specificatio data... 1 Fuctio diagrams... 2 4 Dimesios ad moutig... 41 42 Shaft extesios... 29 Permissible shaft loads... Permissible shaft Seal Pressure... 1 Order code... 4 GENERAL ax. Displacemet, cm /rev [i /rev ax. Speed, [RP ax. Torque, [ ax. Output, kw [HP ax. Pressure Drop, bar [PSI ax. Oil Flow, lpm [GP i. Speed, [RP Pressure fluid O O Temperature rage, C[ F 2 Optimal Viscosity rage, mm /s [SUS Filtratio OPTIONS» odel- Spool valve, roll-gerotor» Flage mout» otor with eedle bearig» Side ad rear ports» Shafts- straight, splied ad tapered» Shaft seal for high ad low pressure» etric ad BSPP ports» Speed sesorig» Other special features 97 [ 24.4 97 : 61 [ 4 : 69 [6 1 [.1 : 17 [ 24 : [29 7 [ ieral based- HLP(DIN 124) or H(ISO 674/4) -4 14 [- 4 284 7 [ 98 47 ISO code /16 (i. recommeded fluid filtratio of 2 micro) Oil flow i drai lie Pressure Losses p bar p PSI Pressure drop bar [ PSI 14 [ 2 [ 4 Viscosity Oil flow i drai lie 2 mm /s [ SUS lpm [ GP [ 98 [ 164 [98 [164 2, [.66 1,8 [.476, [.92 2,8 [.74 2 1 4 2 4 6 8 12 14 16 18 Q, GP 4 6 7 8 Q, lpm HT / E / 4 / 211 / E Pag.
R otors SPECIFICATION DATA Specificatio Data for R... motors with C, CO, SH, K ad SA shafts. (ø28,6 sealig diameter) Displacemet, Type cm /rev R 1, R 8 8, R 99,8 R 12 12,7 R 16 19,6 R 199,8 R 2 2,1 R 1 1,7 R 4 97 [ i /rev [.14 [ 4.9 [ 6.9 [ 7.67 [ 9.74 [ 12.19 [ 1.26 [ 19.26 [ 24.4 ax. Speed, 77 7 6 47 7 24 19 1 [RP 97 94 7 6 47 7 24 19 ax. Torque [ 9 [ 177 24 [ 212 [ 26 9 [ 4 8,[ 4 9 [ 4 6 [ 18 8 [ 6 [ i-lb 1 [ 11 22 [ 1947 28 [ 248 4 [ 4 [ 8 46 [ 47 47 [416 47 [416 47 [416 Peak** 17 [ 1 27 [ 29 2 [ 282 7 [ 27 46 [ 47 6 [ 496 6 [ 61 [4 61 [4 ax. Output 7 [ 9. 12, [ 17 1 [ 17.4 12,[ 16.8 11,[ 1.4 9 [ 12 8 [.7 [6.7 4,8 [ 6.4 kw [ HP 8, [ 11.9 1 [.1 1 [.1 14,[ 19. 14 [ 18.8 12 [16.1 9, [ 12.7 8 [.7 6,8 [9.1 ax. Pressure Drop 14[ 17[ 24 17[ 24 17[ 24 17[ 24 14[ 1[ 16 8 [12 6 [94 bar [ PSI 17[ 24 [ 29 [ 29 [ 29 [ 29 17[ 24 14[ 11[167 9 [1 Peak** 22[ 26 22[ 26 22[ 26 22[ 26 22[ 26 22[ 26 [29 1[217 11[167 ax. Oil Flow 4 [. 6 [ 1.8 6 [ 1.8 6 [1.8 6 [1.8 6 [1.8 6 [1.8 6 [1.8 6 [1.8 lpm [ GP [ 1.2 7 [19.8 7 [19.8 7 [19.8 7 [19.8 7 [19.8 7 [19.8 7 [19.8 7 [19.8 ax. Ilet Pressure 17[ 24 17[ 24 17[ 24 17[ 24 17[ 24 17[ 24 17[ 24 17[ 24 17[ 24 bar [ PSI [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 Peak** 22[ 26 22[ 26 22[ 26 22[ 26 22[ 26 22[ 26 22[ 26 22[ 26 22[ 26 ax. Retur Pres- 17[ 24 17[ 24 17[ 24 17[ 24 17[ 24 17[ 24 17[ 24 17[ 24 17[ 24 sure with Drai Lie [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 bar [ PSI Peak** 22[ 26 22[ 26 22[ 26 22[ 26 22[ 26 22[ 26 22[ 26 22[ 26 22[ 26 ax. Startig Pressure with Uloaded Shaft, bar [ PSI [ 14 [ 14 [ 14 9 [ 1 7 [ 2 [ 7 4 [ 8 [ 44 [ 44 i. Startig Torque At max.press. [ i-lb drop 8 [ 7 1 [ 1 [ 177 2 [ 221 2 [ 282 [ 29 1 [ 274 1,[287 1,[ 287 At max.press. drop [ 8 17 [ 1 2 [ 28 [ 248 7 [ 27 4 [ 4 48 [ 42 8 [ 2 [ 442 i. Speed***, [RP Weight, kg [ lb R(F) 6,8 [ 1 6,9 [ 1,2 7,2 [ 1.9 7, [ 16.1 7, [ 1.2 8 [ 17.6 8,4 [ 18. 9,1 [ 9,8 [ 21.6 For rear ports : +,6 [ 1.4 RQ(N) 6,2 [ 1.7 6, [ 1.9 6,6 [ 14.6 6,8 [ 1 7,6 [ 1.4 7,2 [ 14.7 7,8 [ 17.2 8,6 [ 19 9, [. * Itermittet operatio: the permissible values may occur for max. % of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1 mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. Pag. 4 HT / E / 4 / 211 / E
R otors SPECIFICATION DATA (cotiued) Specificatio Data for R... motors with CB, KB, OB ad HB shafts. (ø sealig diameter) Type Displacemet, cm /rev [i /rev ax. Speed, [RP ax. Torque [ i-lb ax. Output kw [ HP ax. Pressure Drop bar [ PSI ax. Oil Flow lpm [ GP ax. Ilet Pressure bar [ PSI ax. Retur Pressure with Drai Lie bar [ PSI ax. Startig Pressure with Uloaded Shaft, bar[ PSI i. Startig Torque [ i-lb i. Speed***, [RP Weight, kg [ lb For rear ports : +,6 [ 1.4 Peak** Peak** Peak** Peak** At max.press. drop At max.press. drop R 1, R 8 R R 12 R 16 R R 2 R 1 R 4 [.14 77 [ 4.9 7 [ 6.9 6 [ 7.67 47 [ 9.74 7 [ 12.19 [ 1.26 24 [ 19.26 19 [ 24.4 1 97 94 7 6 47 7 24 19 [ 9 [ 177 24 [ 212 [ 26 9 [ 4 4 [ 4 4 [ 478 [ 487 61 [ 4 1 [ 11 17 [ 1 22 [ 1947 27 [ 29 28 [ 248 2 [ 282 4 [ 7 [ 27 4 [ 8 46 [ 47 [ 442 6 [ 496 61 [ 4 71 [ 628 69 [ 61 84 [ 74 69 [ 61 87 [ 77 7 [ 9. 12, [ 17 1 [ 17.4 12,[ 16.8 11, [ 1.4 11 [ 14.8 [ 1.4 9 [ 12 7,8 [. 8, [ 11.9 1 [.1 1 [.1 14,[ 19. 14 [ 18.8 1 [ 17.4 12 [ 16.1 [ 1.4,6[ 14.2 14[ 17[ 24 17 [ 24 17[ 24 17[ 24 17[ 24 17 [ 24 1 [ 196 1 [ 16 17[ 24 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 17 [ 24 14[ 22[ 26 22[ 26 22 [ 26 22[ 26 22[ 26 22[ 26 22 [ 26 2 [ 4 17[ 24 4 [. 6 [ 1.8 6 [ 1.8 6 [ 1.8 6 [ 1.8 6 [ 1.8 6 [ 1.8 6 [ 1.8 6 [ 1.8 [ 1.2 7 [19.8 7 [19.8 7 [19.8 7 [19.8 7 [19.8 7 [19.8 7 [19.8 7 [19.8 17[ 24 17[ 24 17 [ 24 17[ 24 17[ 24 17[ 24 17 [ 24 17 [ 24 17[ 24 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 22[ 26 22[ 26 22 [ 26 22[ 26 22[ 26 22[ 26 22 [ 26 22 [ 26 22[ 26 17[ 24 17[ 24 17 [ 24 17[ 24 17[ 24 17[ 24 17 [ 24 17 [ 24 17[ 24 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 [ 29 22[ 26 22[ 26 22 [ 26 22[ 26 22[ 26 22[ 26 22 [ 26 22 [ 26 22[ 26 [ 14 8, [ 14 99,8 [ 14 12,7 9 [ 1 7 19,6 [ 2 199,8 4 2,1 1,7 8 [ 7 1 [ 1 [ 177 2 [ 221 2 [ 282 41 [ 6 [ 442 [ 442 [ 442 [ 88 17 [ 1 2 [ 28 [ 248 7 [ 27 46 [ 47 [ 487 66 [ 84 61 [ 4 6,9 [ 1,2 7 [ 1,4 7, [ 16.1 7,4 [ 16. 7,6 [ 1.4 8,1 [ 18.9 8, [ 18.7 9,2 [. 9,9 [ 21.8 [ 7 [ 8 [ 44 97 [ 44 * Itermittet operatio: the permissible values may occur for max. % of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1 mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. HT / E / 4 / 211 / E Pag.
R otors R FUNCTION DIAGRAS 1 9 8 7 6 4 12 11 9 8 7 6 4 2 1 it. Q= 1. GP GP 2.6 GP 1 4.,kW GP. 1kW 2 6.6 GP 2kW 7.9 GP 9.2 GP 4kW 4.6 GP 6kW 8kW 4 11.9 GP 1.2 GP p=17 bar 24 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 7 bar PSI bar 7 PSI bar 4 PSI 4 6 7 8 9 RP R 8 18 22 Q= 1. GP 2.6 GP. GP GP 7.9 4.6 GP 1.2 GP 6 1.9 GP GP 7 18. 7 19.8 GP p= bar 29 PSI 16 14 8 6 4 18 16 14 12 8 6 4 2 4 6 7 8 9 RP 17 bar 24 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI bar 4 PSI The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. Pag. 6 HT / E / 4 / 211 / E
R otors R FUNCTION DIAGRAS Q= 1. GP 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP GP 6 1.9 7 18. GP 7 19.8 GP 2 28 1 24 16 12 it. p= bar 29 PSI 17 bar 24 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 8 bar 116 PSI 4 6 bar 87 PSI bar 4 PSI 4 6 7 RP R 12 Q= 1. GP 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 6 28 24 16 8 4 2 p= bar 29 PSI 28 17 bar 24 PSI 24 16 12 8 4 c ot. it. 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI bar 4 PSI 4 6 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. HT / E / 4 / 211 / E Pag. 7
R otors R 16 FUNCTION DIAGRAS 4 44 Q= 1. GP 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP GP 7 19.8 6 28 24 16 8 4 6 2 28 24 16 12 8 it. p= bar 29 PSI 17 bar 24 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 4 4 1 2 4 4 bar 4 PSI RP R Q= 1. GP 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 4 4 2 1 4 4 2 1 it. p= bar 29 PSI 17 bar 24 PSI 14 bar PSI 1 bar 174 PSI bar 1 PSI 8 bar 116 PSI 6 bar 87 PSI 1 2 bar 4 PSI RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. Pag. 8 HT / E / 4 / 211 / E
R otors R 2 FUNCTION DIAGRAS 6 4 4 2 1 6 6 4 4 2 1 Q= 1. GP it. 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 2 7 12 1 17 22 2 27 p= bar 29 PSI 17 bar 24 PSI 14 bar PSI 1 bar 16 PSI bar 1 PSI 8 bar 116 PSI 6 bar 87 PSI bar 4 PSI RP R 1 6 6 4 4 72 64 6 48 4 Q= 1. GP c ot. it. 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP p=17 bar 24 PSI 16 bar 2 PSI 1 bar 174 PSI 12 bar 18 PSI 2 1 2 24 16 8 8 bar 116 PSI 6 bar 94 PSI 4 bar 6 PSI bar 4 PSI 2 7 12 1 17 22 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. HT / E / 4 / 211 / E Pag. 9
R otors FUNCTION DIAGRAS R 4 6 48 44 4 6 28 24 16 8 4 64 6 6 2 48 44 4 6 2 28 24 16 12 8 4 Q= 1. GP 2.6 GP 1 4. GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP GP 7 19.8 4 6 7 8 9 1 1 1 14 1 16 17 18 19 p=12 bar 18 PSI 1 bar 16 PSI 9 bar 1 PSI 8 bar 116 PSI 6 bar 94 PSI bar 8 PSI 4 bar 8 PSI bar 4 PSI RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. Pag. 4 HT / E / 4 / 211 / E
R otors DIENSIONS AND OUNTING DATA SA Shaft SH Shaft K Shaft C Shaft CO Shaft SA Shaft SH Shaft K Shaft C Shaft CO Shaft max [2.16 max [2.16 Shaft Dim. See Page 29 max 49 [1.929 max 49 [1.929 L max 8±,1 [1.496±.9 P (A,B) Port A C Port B 74±, [2.91±.118 Flage Dim. See Page 42 L max P (A,B) 44±,1 [1.72±.9 Port A 8±, [.149±.118 Port B C L1 Port Dim. See Page 42 L1 T max ø [ 4,14 max ø [ 4,14 E Rear ports OB Shaft KB Shaft CB Shaft HB Shaft L max max 7 [2.76 max 68, [2.689 SB Shaft max 14 [.1 mm [i C P T (A, B) : 4x8-1 mm [.1 i depth : 2xG1/2 or 2x22x1, - 1 mm [.9 i depth : G1/4 or 14x1, - 12 mm [.47 i depth (plugged) Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized -CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized -CW Type L, mm [i Type L, mm [i Type L, mm [i Type L, mm [i L,mm 1 [i R(F) R(F) 8 R(F) R(F) 12 R(F) 16 R(F) R(F) 2 R(F) 1 R(F) 4 18, [.4 14, [.6 146, [.7 1, [.9 16, [6.16 16, [6.44 172, [6.77 18, [7. 198, [7.8 RQ RQ 8 RQ RQ 12 RQ 16 RQ RQ 2 RQ 1 RQ 4 14, [.6 148, [.8 12, [.98 16, [6.16 162, [6.4 169, [6.67 179, [7. 189, [7.44 4, [8. R(F)E R(F)E 8 R(F)E R(F)E 12 R(F)E 16 R(F)E R(F)E 2 R(F)E 1 R(F)E 4 17, [6. 162, [6.4 16, [6.2 17, [6.69 176, [6.9 18, [7. 192, [7.6 4, [8. 218, [8.8 RQE RQE 8 RQE RQE 12 RQE 16 RQE RQE 2 RQE 1 RQE 4 16, [6.44 168, [6.6 171, [6.7 176, [6.9 182, [7.17 189, [7.44 198, [7.8 2, [8.27 224, [8.82 9, [. 14, [. 17,4 [.69 21,8 [.86 27,8 [1.9 4,8 [1.7 4, [1.71 4,8 [2.16 69,4 [2.7 HT / E / 4 / 211 / E Pag. 41
R otors 2xø1, +,4 [.2 +.16 Oval out (2 Holes) OUNTING 8±, [.1±.118 1 [.118 ø6,4±,2 [4.189±.79 F - Oval out (4 Holes) ±,1 [2.16±.9 max 7, [ 4,22 Q - Square out (4 Bolts) ±,1 [2.16±.9 ø82,±,1 [.2±.9 mi 1 deep [.9 82 [.228 ø82,±, [.248±.19 ø82,±, [.248±.19 16 [.6 4 4xø1, +,4 [.2 +.16 ø6,4±,2 [4.189±.79 8±, [.1±.118 4x 16 [.6 ø44,4±, [1.748±.19 1 [.118 ±,1 [2.16±.9 max 7, [ 4,22 82 [.228 max 7, [ 4,22 2,±, [.98±.118 mm [i Side Ports PORTS E Rear Ports 18±,1 [.78±.9 ±, [.787±.118 C Port A ±, [.787±.118 max 7, [ 4,22 ±,1 [2.16±.9 max L ±,1 [2.16±.9 [.787 Port A 2 [.984 18±,1 [.78±.9 ±, [.787±.118 C P T (A, B) Port B ±, [.787±.118 P (A,B) : 4x8-1 mm [.1 i depth : 2xG1/2 or 2x22x1, - 1 mm [.9 i depth : G1/4 or 14x1, - 12 mm [.47 i depth (plugged) T 1,2 [1.2 Port B Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized -CCW T 7,1 [.279 P (A,B) [. 197 Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized -CW Pag. 42 HT / E / 4 / 211 / E
R otors ORDER CODE R 1 2 4 6 7 8 9 Pos.1 - outig Flage omit - Oval mout, two holes F - Oval mout, four holes Q -Square mout, four bolts W - Wheel mout Pos.2 - Optio (eedle bearigs) omit - oe N - with eedle bearigs Pos. - Port type omit E Pos.4 - Displacemet code 8 12 16 2 1 4 - Side ports - Rear ports - 1, cm /rev [.14 i /rev - 8, cm /rev [4.9 i /rev - 99,8 cm /rev [6.9 i /rev - 12,7 cm /rev [7.67 i /rev - 19,6 cm /rev [9.74 i /rev - 199,8 cm /rev [12.19 i /rev - 2,1 cm /rev [1.26 i /rev - 1,7 cm /rev [19.26 i /rev - 97, cm /rev [24.4 i /rev Pos. - Shaft Extesios *(see page 29) C VC CO VCO SH VSH K SA VSA - ø2 straight, Parallel key A8x7x2 DIN688 - ø2 straight, Parallel key A8x7x2 DIN688 with corrosio resistat bushig - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 with corrosio resistat bushig - ø2,2 splied BS 9 (SAE 6B) - ø2,2 splied BS 9 (SAE 6B) with corrosio resistat bushig - ø28,6 tapered 1:, Parallel key Bxx14 DIN688 - ø24, splied B 2x22 DIN 482 - ø24, splied B 2x22 DIN 482 with corrosio resistat bushig CB KB SB OB HB - ø2 straight, Parallel key Ax8x4 DIN688 - ø tapered 1:, Parallel key B6x6x DIN688 - splied A 2x22 DIN 482 - ø1¼" tapered1:8, Parallel key "x "x1¼" BS46 - ø1¼" splied 14T ANSI B92.1-1976 Pos. 6 - Shaft Seal Versio (see page 1) omit - Low pressure shaft seal or Stadard shaft seal for... B shaft D - Stadard shaft seal U - High pressure shaft seal (without check valves) Pos. 7 - Drai Port omit - with drai port 1 - without drai port Pos. 8 - Ports omit - BSPP (ISO 228) - etric (ISO 262) Pos. 9 - Special Features (see page 99) Pos. - Desig Series omit - Factory specified * The permissible output torque for shafts must ot be exceeded! NOTES : The followig combiatios are ot allowed: - Q flage with...b shafts; - N optio with...b shafts, Low Pressure Seal or U optio; -...B shafts with D ad U shaft seals. The hydraulic motors are magao-phosphatized as stadard. HT / E / 4 / 211 / E Pag. 4
Hydraulic otors with Tacho Coectio R...T Series R motors are available i versio with tacho drive shaft. With tacho coectio the speed of the motor ca be registered. Tacho shaft has a 6 times higher revolutio speed tha output shaft ad opposite directio of rotatio. A B OUTLINE DIENSIONS REFERENCE ø9 [.4 B 6, [.26, [.4 ±, [.118±.19 22x1, ø [1.181 ø6 [2.62 A 26 [1.24 Drai port - G1/8 (x1 for metric ports) mi mm [.9 i deep max L L1 26,4 [1.9 9 [1. Type R R 8 R R 12 R 16 R R 2 R 1 R 4 L, mm [i 17 162 16 17 176 18 192 4 218 [6.18 [6.8 [6. [6.69 [6.9 [7. [7.6 [8. [8.8 L,mm 1 [i 9, [. 14, [. 17,4 [.69 21,8 [.86 27,8 [1.9 4,8 [1.7 4, [1.71 4,8 [2.16 69,4 [2.7 mm [i Note: Radial or axial load o tacho shaft must be avoided. ax. torque o tacho shaft,1 [.88. ax. retur pressure without drai lie bar [29 PSI. The mai techical features correspod to the stadard motors series R. There are o chages i the overall ad moutig dimesios. For detail techical ad moutig data please refer to R catalogue. Pag. 44 HT / E / 4 / 211 / E
Hydraulic otors RNA Series APPLICATION» Actuator motor as drivig-motor for steerig mechaism of the the three-wheel vehicles;» For coveyors (series coectio);» Dosig motor etc. A B RNA is suitable for drive mechaism where is demad smooth operatio low speed ad high pressure. It is desiged with separated output shaft ad spool valve ad ca be specified with low iteral leakage. T L» Good start-up characteristics;» Precise cotrol of the Torque at low small flow.» Smooth operatio at high pressure ad small oil flow;» High volumetric efficiecy. Hydraulic Reservoir R P The mai techical features correspod to the stadard motors series R ø28,6 [1.124 i. sealig diameter. There are o chages i the overall ad moutig dimesios. For detail techical ad moutig data please refer to R catalogue. SPECIFICATION DATA Code RNA RNA RNA RNA RNA RNA RNA RNA RNA 8 12 16 2 1 4 Displacemet cm /rev [i /rev 1, [.14 8, [4.9 99,8 [6.9 12,7 [7.67 19,6 [9.74 199,8 [12.19 2,1 [1.26 1,7 [19.26 97, [24.4 ax. ax. Torque ax. Output ax. Pressure ax. Oil Speed [ kw [HP Drop, bar [PSI Flow, lpm [RP C, CO shafts SH, SA shafts C, CO shafts SH, SA shafts C, CO shafts SH, SA shafts [GP it* it* it* it* it* it* 19 1 1 1 2, 2, 2, 2, 14 17 14 17 [88 [11 [88 [11 [2.68 [. [2.68 [. [ [24 [ [24 22 22,,,, 17 17 [177 [194 [177 [194 [4.2 [4.69 [4.2 [4.69 [24 [29 [24 [29 24 28 24 28 4,, 4,, 17 17 21 [248 21 [248 [6. [6.71 [6. [6.71 [24 [29 [24 [29 4 4, 6,, 6, 17 17 [26 [ [26 [ [7.7 [8. [7.7 [8. [24 [29 [24 [29 29 9 9 4, 6, 6, 7, 1 17 17 [26 [4 [4 [8 [6.71 [8. [8. [. [174 [24 [24 [29 29 8, 8, 46, 7, 6, 9, 14 14 17 [26 [4 [4 [47 [6.71 [9.9 [8.72 [12.6 [1 [ [ [24 9 9 47, 7, 6, 9, 8 1 1 14 [26 [4 [4 [416 [6.71 [9.9 [8. [12.6 [116 [16 [16 [ 42 6 47, 7, 6, 8, 7 8 11 [26 [7 [4 [416 [6.71 [. [8. [11.4 [ [14 [12 [167 4 8 47 4, 6, 6, 7, 7 6 9 [26 [4 [26 [416 [[.6 [8.72 [8. [9.9 [8 [1 [94 [1 * Itermittet operatio: the permissible values may occur for max. % of every miute., [2.8 16 [4.2 [. 2 [6.6 2 [8. 4 [. [1.2 6 [17.2 6 [1.8 HT / E / 4 / 211 / E Pag. 4
Hydraulic otors RFL Series The hydraulic motors type RFL... ad LHRFL... are desiged for use i operatig modes with peak radial loads of the output shaft (especially at startig ad stoppig) at direct drive of wheels or mechaisms (without clutch or gearbox). The radial loads are bore by a radial ball bearig which is mouted o the shaft of the hydraulic motor. The mai techical features correspod to the stadard motors series RF ø [1.78 i. sealig diameter. There are o chages i the overall ad moutig dimesios. For detail techical ad moutig data please refer to R catalogue. PERISSIBLE SHAFT LOADS AX. PERISSIBLE SHAFT SEAL PRESSURE Pr dan Prad 2. 2 1. 1. -1. i lbs 2 8 6 1 P bar 1 P PSI 4 1 7 6 4 - mm 4 6 7 8, RP - cotiuous operatios - itermittet operatios Pag. 46 HT / E / 4 / 211 / E
OPTIONS» odel- Spool valve, roll-gerotor;» Dual shaft;» Oval flage;» Side port;» Straight shafts;» BSPP ports;» Other special features. APPLICATION»»»» Coveyors; Feedig mechaism of robots ad maipulators; etal workig machies; Textile machies;» Agriculture machies;» Food idustries;» iig machiery etc. OUTLINE DIENSINS REFERENCE Parallel key A8x7x DIN 688 "A" - SHAFT typec 8 [.1 1 [.9 9, [2.42 8 [.1 1 [.9 8 [.1 Parallel key A8x7x DIN 688 "B" - SHAFT typec 6, [.26 +, ø82, +.19 [.248 2 8 -, [ 1.2 8 -.11 Hydraulic otors with Dual Shaft RB... Series P (A,B) 6, [.26 C -,21 ø2 8 [.984 -.8 22 [.866 4 [1.69 4 [1.74 max ø2 [4.16 ø [.97 22 [.866 4 [1.69 8 -,21 ø2 2 8 -, -.8 [.984 [ 1.2 8 -.11 ø82, [.248 +, +.19 D 2xø1,4 ax, [2.6 [.27 [1.299 T 4 [1.74 max L L1 2xø1,4 [.27 ax, [2.6 C 8 -,6 [.1 -.14 [2.16 D 8 -,6 [.1 -.14 1 [.118 ø6,4 [4.189 T 4 9 [.4 P T Type L, mm [i L,mm 1 [i RB 8, [8.19 9, [. RB 8 21, [8.9 14, [. RB 216, RB 12 2, RB 16 226, RB 2, RB 2 242, RB 2, [8. 17,4 [.69 [8.68 21,8 [.86 [8.92 27,8 [1.9 [9.19 4,8 [1.7 [9. 4, [1.71 [9.98 4,8 [2.16 RB 4 268,[. 69,4 [2.7 (A, B) 78 [.71 : 2xG1/2-18 mm[.71 i depth : G1/8-9 mm [. i depth (plugged) 9 [.4 ax 6, [4.19 6,4 [4.189 1 [.118 mm [i HT / E / 4 / 211 / E Pag. 47
RB otors SPECIFICATION DATA Type RB RB RB RB RB RB RB RB RB C/C 8 C/C C/C 12 C/C 16 C/C C/C 2 C/C 1 C/C 4 C/C Displacemet, cm³/rev [i³/rev 1,[.14 8,[4.9 99,8[6.9 12,7[7.67 19,6[9.74 199,8[12.19 2,1[1.26 1,7[19.26 97 [24.4 ax. Speed, RP * 77 97 7 94 6 7 47 6 7 47 7 24 19 24 1 19 ax. Torque, [88 19, [172 24 [212 [26 [26 [26 [26 [26 [26 [ * 1 [11 22 [1947 28 [248 4 [ 9 [4 9 [4 8 [6 42 [7 4 [8 ax. Torque "A"Shaft, 8 [7 11, [ 12 [6 [177 [177 [177 [177 [177 [177 [ * 9, [84 1 [11 14 [124 2 [ 2 [ 2 [ 2 [ 2 [ 2 [ ax. Torque "B"Shaft, 4 [ 11, [ 12 [6 [177 [177 [177 [177 [177 [177 [ ax. Output, [kw [HP * * [44 7 [9. 8, [11.9 1 [11 12, [17 1 [.1 14 [124 1 [11 1 [.1 2 [ 12, [17 14, 2 [ [1.4 12, [17 2 [ 8 [.7 [1.4 2 [ 6 [8. 8 [.7 2 [ [6.7 6, [8.7 2 [ 4 [.4 6 [8. ax. Pressure Drop, bar [PSI * 14 [ 17 [24 17 [24 17 [24 17 [24 [29 [29 [29 1 [188 17 [24 1 [16 14 [ 8 [116 1 [16 7 [ [14 [8 8 [116 ax. Oil Flow, lpm [GP ax. Retur Pressure without Drai Lie, bar [PSI * - RP - RP - RP 4 [. [1.2 7 [9 [7 [29 6 [1.9 7 [18. 7 [9 [7 [29 6 [1.9 7 [18. 7 [9 [7 [29 6 [1.9 7 [18. 7 [9 [7 [29 6 [1.9 7 [18. 7 [9 [7 [29 6 [1.9 7 [18. 7 [9 [7 [29 6 [1.9 7 [18. 7 [9 [7 [29 6 [1.9 7 [18. 7 [9 [7 [29 6 [1.9 7 [18. 7 [9 [7 [29 * - max RP 7 [9 7 [9 7 [9 7 [9 7 [9 7 [9 7 [9 7 [9 7 [9 * Itermittet operatio: the permissible values may occur for max. % of every miute. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1 mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. Pag. 48 HT / E / 4 / 211 / E
RB otors PERISSIBLE SHAFT LOADS The load diagrams are valid for a average bearigs life of 16 hrs at r.p.m. with mieral base lubricatig cotaiig atiwear additives (ref.iso 281 (.)stadard). The "A" curve gives the maximum static load affordable by the bearigs. The "B" curve gives the radial load top limit without axial load of dan. Pr dan 1 12 7 47 lbs. 2 dan 47 lbs. 2 dan Prad lbs 2 1 Pr 2 A B Pa -4 - - - 4 6 7 8 9 mm -1. -1 -.. 1 1. 2 2.. 4 i ORDER CODE RB 1 2 4 / 6 Pos.1 - Displacemet code - 1, cm /rev [.14 i /rev 8-8, cm /rev [4.9 i /rev - 99,8 cm /rev [6.9 i /rev 12-12,7 cm /rev [7.67 i /rev 16-19,6 cm /rev [9.74 i /rev - 199,8 cm /rev [12.19 i /rev 2-2,1 cm /rev [1.26 i /rev 1-1,7 cm /rev [19.26 i /rev 4-97, cm /rev [24.4 i /rev Pos.2 - "A" Shaft Extesios* C - ø2 straight, Parallel key A8x7x DIN688 Pos. 4 - Special Features omit LSV Pos. - Optio (Pait)** omit P PC - oe - Low Speed Valve - o Pait - Paited - Corrosio Protected Pait Pos. 6 - Desig Series omit - Factory specified Pos. - "B" Shaft Extesios* C - ø2 straight, Parallel key A8x7x DIN688 NOTES: * For other shaft extesios please cotact with "HANSA-TP". ** Color at customer's request. The hydraulic motors are magao-phosphatized as stadard. HT / E / 4 / 211 / E Pag. 49
Hydraulic otors PL Series APPLICATION» Coveyors» Feedig mechaism of robots ad maipulators» etal workig machies» Textile machies» Agriculture machies» Food idustries» iig machiery etc. CONTENTS Specificatio data... 1 Dimesios ad moutig... 2 Shaft extesios... Permissible shaft loads... 4 Order code... 4 OPTIONS» odel- Spool valve, gerotor» Atifrictio coical bearig» Flage mout» Shafts- straight, splied ad tapered» etric ad BSPP ports» Other special features GENERAL ax Displacemet, cm /rev [i /rev ax. Speed, [RP ax. Torque, [ ax. Output, kw [HP ax. Pressure Drop, bar [PSI ax. Oil Flow, lpm [GP i. Speed, [RP Pressure fluid O O Temperature rage, C[ F 2 Optimal Viscosity rage, mm /s [SUS Filtratio 96 [24.16 11 : [ 441 : 9 [222 17, [2. : 14 [ : 17 [24 7 [ ieral based- HLP(DIN 124) or H(ISO 674/4) -4 14 [-4 284 7 [ 98 47 ISO code /16 (i. recommeded fluid filtratio of 2 micro) Pressure drop bar [ PSI [ 14 14 [ Oil flow i drai lie Viscosity Oil flow i drai lie 2 mm /s [ SUS lpm [ GP [ 98 [ 164 [98 [164 2, [.66 1,8 [.476, [.92 2,8 [.74 p bar 2 1 p PSI 4 Pressure Losses 2 4 6 8 12 14 16 18 Q, GP 4 6 7 8 Q, lpm Pag. HT / E / 4 / 211 / E
PL otors SPECIFICATION DATA Type Displacemet, cm /rev [i /rev. ax. Speed, [RP ax. Torque [i-lb Peak** ax. Output kw [HP ax. Pressure Drop bar [PSI Peak** ax. Oil Flow lpm [GP ax. Ilet Pressure bar [PSI Peak** ax. Retur Pressure - RP without Drai Lie or ax. Pressure - RP -6 RP i Drai Lie, bar [PSI ax. Retur Pressure with Drai Lie bar [PSI ax. Startig Pressure with Uloaded Shaft, bar [PSI Peak** >6 RP -max. RP i. Startig Torque [i-lb i. Speed***, [RP Weight, kg [lb PL 49, [.2 12 11 9,4 [ 82 11,9 [ 4 14, [ 124 9,9 [ 1. 12, [ 16.8 14 [ 17 [ 24 22 [ 26 6 [ 16 7 [ 17 [ 24 [ 29 22 [ 26 [ 14 [72 2 [ 6 1 [ 2 [ 14 17 [ 24 [ 29 22 [ 26 [14 7,7 [ 681 8,4 [ 18. PL 8 79,2 [ 4.8 7 94 1,1 [ 16 19, [ 172 22, [ 1947 9,9 [1. 12, [ 16.8 14 [ 17 [24 22 [26 6 [16 7 [ 17 [24 [29 22 [26 [14 [72 2 [6 1 [2 [14 17 [24 [29 22 [26 [14 1 [ 11 8, [ 18.7 PL 99 [ 6.4 6 7 19, [ 178 PL 12 12,8 [7. 48 6 2,7 [2 2,7 [ 97 29,8 [267 27, [ 29 6, [2 9,9 [1. 9,9 [1. 12, [16.8 12, [16.8 14 [ 14 [ 17 [24 17 [24 22 [26 22 [26 6 [16 6 [16 7 [ 7 [ 17 [24 17 [24 [29 [29 22 [26 22 [26 [14 [14 [72 [72 2 [6 2 [6 1 [2 1 [2 [14 [14 17 [24 17 [24 [29 [29 22 [26 22 [26 PL 16 18,4 [9.66 78 472 1, [277 7,8 [4 42 [717 11,7 [1.7 12, [16.8 14 [ 17 [24 22 [26 6 [16 7 [ 17 [24 [29 22 [26 [14 [72 2 [6 1 [2 [14 17 [24 [29 22 [26 PL 198 [ 12.1 78 6,6 [ 24 4,6 [ 4 [ 47, [ 1.8 1, [.8 14 [ 17 [24 22 [26 6 [16 7 [ 17 [24 [29 22 [26 [14 [72 2 [6 1 [2 [14 17 [24 [29 22 [26 PL 2 247, [1.1 242 47 [416 8, [16 67 [9 9,8 [1.1 17, [2. 14 [ 17 [24 22 [26 6 [16 7 [ 17 [24 [29 22 [26 [14 [72 2 [6 1 [2 [14 17 [24 [29 22 [26 PL 1 16,8 [19. 19 26 48,6 [4 6 [496 8 [72 7,6 [.2 8,2 [11 1 [1 14 [ 22 [26 6 [16 7 [ 17 [24 [29 22 [26 [14 [72 2 [6 1 [2 [14 17 [24 [29 22 [26 PL 4 96 [24.16 1 189 [442 9 [222 8,4 [76 6,6 [8.9 9,2 [12. 9 [1 11 [166 18 [26 6 [16 7 [ 17 [24 [29 22 [26 [14 [72 2 [6 1 [2 [14 17 [24 [29 22 [26 [14 9 [11 8 [116 7 [ 6 [87 [7 [7 16,8 [ 1487 21, [186 28, [2478 2,2 [ 28 41,4 [66 4, [8 44, [9 8,8 [ 19.4 8,9 [19.6 9,1 [ 9, [.9, [22,7 [2.6 11,4 [2.1 * Itermittet operatio: the permissible values may occur for max. % of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1 mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. HT / E / 4 / 211 / E Pag. 1
PL otors DIENSIONS AND OUNTING DATA SH Shaft SA Shaft HB Shaft C Shaft KB Shaft CB Shaft CO Shaft 67, [2.67 4 [2.126 4 [2.126 4 [2.126 61 [2.42 68, [2.697 Shaft Dim. See Page 81, [.21 Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized -CCW 8±,1 [.1±.9 Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized -CW L Port A Port B max ±,1 [.787±.9 T P (A,B) ±,1 [.787±.9 L1 Type PL PL 8 PL PL 12 PL 16 PL PL 2 PL 1 PL 4 L max, mm [i 148 [.8 12 [.98 1 [ 6. 18 [ 6.22 16 [ 6.42 168 [ 6.61 17 [6.89 184 [7.24 19 [7.68 L, 1 mm [i 6,67 [.26,67 [.42 1, [.2 16,67 [.66 21, [.84 26,67 [ 1., [1.1 42,67 [1.68, [2. ø86 [.86 ø2 [4.16 P T (A,B) : 2xG1/2 or 2x22x1, - 1 mm [.9 i depth : G1/4 or 14x1, - 12 mm [.47 i depth OUNTING Square out (4 Holes) F Oval out (4 Holes) 1 [.119 [2.17 4xø1, [. 17 [.669 8±, [.1±.118 4 o 4xø1, [. ø6,4±,2 [4.19±.79 17 [.669 8±, [.1±.118 ø82,±, [.248±.19 max 16 [.4 ø82,±, [.248±.19 2 [4.16 ø6,4±,2 [4.19±.79 81, [.21 [2.17 max 96 [.78 81, [.21 mm [i Pag. 2 HT / E / 4 / 211 / E
SHAFT EXTENSIONS C - ø2 straight, Parallel key A8x7x DIN 688 ax. Torque 4 [ SA - splied B2x22 DIN 482 ax. Torque 4 [4 8 -,6 [.1 -.14 ±, 1.18±,2 2 8 -, [ 1.1 8 -.11 8 mi 22 Deep [.866 ø [1.78 4 [1.69 ø 2 1 -,2 [.98 8 -. 8 mi 22 Deep [.866 ø [1.78 4 [1.69 ø 24 -,1 [.94 1 -. CO - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 ax. Torque 4 [ CB - ø2 straight, Parallel key Ax8x4 DIN 688 ax. Torque 77 [681 6,4 -, [.22-.2,±,2 [.217±.79 1, +,1 [. +.9 -,6 [.94 -.14 +,1 -,1 +.9 -. 2 8 [ 1.1 8 mi 22 Deep [.866 ø [1.78 4 [1.69 ø 2,9 1 -, [.94 9 -. ø 2,4 1 -,2 [.98 9 -.99 2 -, [ 1.8 9 -.7 8 mi 22 Deep [.866 ø [1.78 [1.97 +,18 ø2 [ 1.26 +,2 +.7 +.1 SH - splied, BS 9 (SAE 6B) ax. Torque 4 [4 HB -ø1¼" splied 14T, DP12/24 ANSI B92.1-1976 ax. Torque 9 [84 6,2-, [.246-.2 2,7 +1 +.9 [1.1 8±, [1.49±.19 ø 2, [.996 9 -,1 -,1 -.9 -. -,8 ø21,6-,12 -.1 [.8 -.49 8 mi 22 Deep [.866 ø [1.78 1, [. 4 [1.69 ø 2,9 1 -, [.94 -.9 7 [.26 8 mi 22 Deep [.866 ø [1.78 6 [2.2 ø 1,7 -, -,1 -.19 -.9 [ 1.2 KB - tapered 1:, Woodruff key 6x9 DIN6888 ax. Torque 9 [84 6 -, [.26-.12 ø22-,21 [.866-.8 S= Tighteig Torque ±1 [.94±.94 1 9 9 -,2 ø [1.78 PL otors 1: A 18 [.78 [.748 4 -.11 x1, ø4, [.18 ø7 [1.4 A 6 [1.417,8 [.228 8 [2.28 mm [i HT / E / 4 / 211 / E Pag.
PL otors Permissible Shaft Loads PL ad RL The load diagrams are valid for a average bearigs life of 16 hrs at RP. Pr dan 2 1 Pr lbs. 7 6 4 A 4 2 1-1 -1.7 i. B C max Pa= dan [1124 lbs Pr 8 6 4 - -4 mm A - ax. static load affordable by the bearigs. B - ax. radial load at a axial load Pa= dan [4 lbs C - ax. radial load at a axial load Pa= dan [1124 lbs ORDER CODE PL 1 2 4 6 Pos.1 - outig Flage omit - Square mout, four holes F - Oval mout, four holes Pos.2 - Displacemet code* 8 12 16 2 1 4-49, cm /rev [.2 i /rev - 79,2 cm /rev [4.8 i /rev - 99, cm /rev [6.4 i /rev - 12,8 cm /rev [7. i /rev - 18,4 cm /rev [9.66 i /rev - 198, cm /rev [12. i /rev - 247, cm /rev [1. i /rev - 16,8 cm /rev [19. i /rev - 96, cm /rev [24.16 i /rev Pos. - Shaft Extesios* * C CO SH SA CB HB KB - ø2 straight, Parallel key A8x7x DIN688 1 1 1 - ø1" straight, Parallel key / 4"x / 4"x1 / 4" BS46 - ø2, splied, BS 9 (SAE 6B) - ø24 splied, B 2x22 DIN 482 - ø2 straight, Parallel key Ax8x4 DIN688 1 - ø1 / 4" splied 14T ANSI B92.1-1976 - ø tapered 1:, Woodruff key 6x9 DIN6888 Pos.4 - Ports omit - BSPP (ISO 228) - etric (ISO 262) Pos. - Special Features (see page 99) Pos.6 - Desig Series omit - Factory specified NOTES: * For the Fuctio Diagrams data please look at "HANSA-TP" Catalogue for P motors, pages 24. ** The permissible output torque for shafts must ot be exceeded! The hydraulic motors are magao-phosphatized as stadard. Pag. 4 HT / E / 4 / 211 / E
Hydraulic otors RL Series APPLICATION» Coveyors» Feedig mechaism of robots ad maipulators» etal workig machies» Textile machies» Agriculture machies» Food idustries» iig machiery etc. CONTENTS Specificatio data... 6 Permissible shaft loads... 4 Dimesios ad moutig... 7 Shaft extesios... 8 Order code... 8 OPTIONS» odel- Spool valve, roll-gerotor» Atifrictio coical bearigs» Flage mout» Shafts- straight, splied ad tapered» etric ad BSPP ports» Other special features GENERAL ax. Displacemet, cm /rev. [i /rev. ax. Speed, [RP ax. Torque, [ ax. Output, kw [HP ax. Pressure Drop, bar [PSI ax. Oil Flow, lpm [GP i. Speed, [RP Permissible Shaft Loads, Pressure fluid Temperature rage, Optimal Viscosity rage, Filtratio dan [lbs O C[ F O 2 mm /s [SUS 97 [ 24.4 97 : 61 [ 4 : 69 [6 16 [21. :17 [ 24 : [29 7 [ P = [1124 a ieral based- HLP(DIN 124) or H(ISO 674/4) -4 14 [-4 284 7 [ 98 47 ISO code /16 (i. recommeded fluid filtratio of 2 micro) Pressure drop bar [ PSI [ 14 14 [ Oil flow i drai lie Viscosity Oil flow i drai lie 2 mm /s [SUS lpm [ GP [ 98 [ 164 [98 [164 2, [.66 1,8 [.476, [.92 2,8 [.74 p bar 2 1 p PSI 4 Pressure Losses 2 4 6 8 12 14 16 18 Q, GP 4 6 7 8 Q, lpm HT / E / 4 / 211 / E Pag.
RL otors SPECIFICATION DATA Type Displacemet, cm³/rev [ i³/rev ax. Speed, [RP ax. Torque, [ ax. Output kw [ HP ax. Pressure Drop bar [ PSI ax. Oil Flow lpm [ GP ax. Ilet Pressure bar [ PSI ax. Retur Pressure without Drai Lie or ax. Pressure i Drai Lie, bar [ PSI ax. Retur Pressure with Drai Lie bar [PSI ax. Startig Pressure with Uloaded Shaft, bar [PSI i. Startig Torque [ i. Speed***, [RP Weight, kg [ lb Peak** Peak** Peak** - RP - RP -6 RP >6 RP -max. RP Peak** RL 1, [.14 77 97,1 [ 9 1 [ 11 17 [ 1 7 [ 9. 8, [ 11.9 14 [ 17 [ 24 22 [ 26 4 [ 11 [ 1 17 [ 24 [ 29 22 [ 26 [ 14 [ 72 2 [ 6 1 [ 2 [ 14 14 [ 17 [24 22 [ 26 [ 14 8 [ 7 8, [ 18.7 RL 8 8, [ 4.9 7 94 [ 177 22, [ 1947 27, [ 29 12, [ 17 1 [.1 17 [ 24 [ 29 22 [ 26 6 [ 16 7 [ 17 [24 [29 22 [26 [14 [72 2 [6 1 [2 [14 17 [24 [29 22 [26 [ 14 1 [1 8,6 [ 19 RL RL 12 99,8 [6.9 12,7 [ 7.67 6 47 7 6 24 [212 [ 26 28 [248 4 [ 2 [282 7 [ 27 1 [17.4 12, [ 16.8 1 [.1 16 [ 21. 17 [24 17 [24 [29 [29 22 [26 22 [26 6 [16 6 [16 7 [ 7 [ 17 [24 17 [24 [29 [29 22 [26 22 [26 [14 [14 [72 [72 2 [6 2 [6 1 [2 1 [2 [14 [14 17 [24 17 [24 [29 [29 22 [26 22 [26 [14 [ 177 8,9 [19.6 9 [ 1 2 [ 221 9, [ 19.8 RL 16 19,6 [9.74 7 47 9 [4 4 [8 46 [47 11, [1.4 14 [18.8 17 [24 [29 22 [26 6 [16 7 [ 17 [24 [29 22 [26 [14 [72 2 [6 1 [2 [14 17 [24 [29 22 [26 2 [7 28 [2 9,2 [. RL RL 2 RL 1 RL 4 199,8[12.19 2,1[1.26 1,7[19.26 97 [ 24.4 7 4 [4 [442 6 [496 11 [14.8 1 [17.4 17 [24 [29 22 [26 6 [16 7 [ 17 [24 [29 22 [26 [14 [72 2 [6 1 [2 [14 17 [24 [29 22 [26 24 4 [478 61 [4 71 [628 [1.4 12 [16.1 17 [24 [29 22 [26 6 [16 7 [ 17 [24 [29 22 [26 [14 [72 2 [6 1 [2 [14 17 [24 [29 22 [26 19 24 [487 6 [8 8 [7 9 [12 11 [14.8 1 [196 16 [2 2 [4 6 [16 7 [ 17 [24 [29 22 [26 [14 [72 2 [6 1 [2 [14 17 [24 [29 22 [26 1 19 61 [ 4 69 [ 6 87 [ 77 7,8 [.,6 [ 14.2 11 [ 167 14 [ 17 [ 24 6 [16 7 [ 17 [24 [29 22 [26 [14 [72 2 [6 1 [2 [14 17 [24 [29 22 [26 [7 7 [27 9,6 [21.2 4 [8 4 [4,1 [22. [44 4 [4,8 [2.8 [44 49 [ 44 11, [ 2.4 * Itermittet operatio: the permissible values may occur for max. % of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1 mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. Pag. 6 HT / E / 4 / 211 / E
RL otors DIENSIONS AND OUNTING DATA SH Shaft HB Shaft C Shaft KB Shaft CB Shaft 67, [2.67 4 [2.126 4 [2.126 61 [2.42 L 68, [2.697 max Port A ±,1 [.787±.9 ø [.97 ø2 [4.16 T ±,1 [.787±.9 8±,1 [.1±.9 L1 81, [.21 Port B P (A,B) P T (A,B) Shaft Dim. See Page 8 Type RL RL 8 RL RL 12 RL 16 RL RL 2 RL 1 RL 4 Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized -CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized -CW L,mm [i 12 [.98 17 [ 6.18 16 [ 6. 16 [ 6. 171 [ 6.7 178 [ 7.1 187 [7.6 198 [7.8 212 [8. L, 1 mm [i 9, [. 14, [. 17,4 [.69 21,8 [.86 27,8 [ 1.9 4,8 [ 1.7 4, [1.71 4,8 [2.16 69,4 [2.7 : 2xG1/2 or 2x22x1, - 1 mm [.9 i depth : G1/4 or 14x1, - 12 mm [.47 i depth Square out (4 Holes) F Oval out (4 Holes) 1 [.119 [2.17 4xø1, [. 17 [.669 8±, [.1±.118 4 o 4xø1, [. ø6,4±,2 [4.19±.79 17 [.669 8±, [.1±.118 ø82,±, [.248±.19 max 16 [.4 ø82,±, [.248±.19 OUNTING 2 [4.16 ø6,4±,2 [4.19±.79 81, [.21 [2.17 max 96 [.74 81, [.21 mm [i HT / E / 4 / 211 / E Pag. 7
SHAFT EXTENSIONS C - ø2 straight, Parallel key A8x7x DIN 688 ax. Torque 4 [ 8 -,6 [.1 -.14 CB - ø2 straight, Parallel key Ax8x4 DIN 688 ax. Torque 77 [681 -,6 [.94 -.14 2 8 -, RL otors [ 1.1 8 -.11 8 mi 22 [.866 Deep ø [1.78 4 [1.69 ø 2 1 -,2 [.98 8 -. 2 -, [ 1.8 9 -.7 8 mi 22 [.866 Deep ø [1.78 [1.97 +,18 ø2 [ 1.26 +,2 +.7 +.1 SH - splied, BS 9 (SAE 6B) ax. Torque 4 [4 ø 2, [.996 9 -,1 -,1 -.9 -. 6,2-, [.246-.2 -,8 ø21,6-,12 -.1 [.8 -.49 8 mi 22 [.866 Deep ø [1.78 2,7 +1 +.9 [1.1 ø 2,9 1 -, [.94 -.9 1, [. 7 4 [.26 [1.69 KB - tapered 1:, Woodruff key 6x9 DIN6888 ax. Torque 9 [84 A-A 6 -, [.26-.12 ø22-,21 [.866-.8 1: A HB -ø1¼" splied 14T, DP12/24 ANSI B92.1-1976 ax. Torque 9 [84 ø [1.78 8 mi 22 [.866 Deep 18 [.78 S= Tighteig Torque ±1 [.94±.94 8±, [1.49±.19 6 [2.2 ø 1,7 -, -,1 -.19 -.9 [ 1.2 1 9 9 -,2 [.748 4 -.11 ø [1.78 A 6 [1.417,8 [.228 x1, ø4, [.18 ø7 [1.4 mm [i 8 [2.28 RL Pos.1 - outig Flage 1 2 4 6 omit - Square mout, four holes F - Oval mout, four holes Pos.2 - Displacemet code* 8 12 16 2 1 4-1, cm /rev [.14 i /rev - 8, cm /rev [4.9 i /rev - 99,8 cm /rev [6.9 i /rev - 12,7 cm /rev [7.67 i /rev - 19,6 cm /rev [9.74 i /rev - 199,8 cm /rev [12.19 i /rev - 2,1 cm /rev [1.26 i /rev - 1,7 cm /rev [19.26 i /rev - 97, cm /rev [24.4 i /rev ORDER CODE Pos. - Shaft Extesios* * C CB SH HB KB - ø2 straight, Parallel key A8x7x DIN688 - ø2 straight, Parallel key Ax8x4 DIN688 - ø2, splied, BS 9 (SAE 6B) 1 - ø1 / 4" splied 14T ANSI B92.1-1976 - ø tapered 1:, Woodruff key 6x9 DIN6888 Pos.4 - Ports omit - BSPP (ISO 228) - etric (ISO 262) Pos. - Special Features (see page 99) Pos.6 - Desig Series omit - Factory specified NOTES: * For the Fuctio Diagrams data please look at "HANSA-TP" Catalogue for R motors, pages 8 42. ** The permissible output torque for shafts must ot be exceeded! The hydraulic motors are magao-phosphatized as stadard. Pag. 8 HT / E / 4 / 211 / E
Hydraulic otors PK Series APPLICATION»»»» Coveyors Feedig mechaism of robots ad maipulators etal workig machies Textile machies» Agriculture machies» Food idustries» iig machiery etc. CONTENTS Specificatio data... 6 Dimesios ad moutig... 61 Shaft extesios... 62 Order code... 62 OPTIONS» odel- Spool valve, gerotor» Atifrictio coical bearig» Flage mout» Shafts- straight, splied ad tapered» etric ad BSPP ports» Other special features GENERAL ax. Displacemet, cm /rev [i /rev ax. Speed, [RP ax. Torque, [ ax. Output, kw [HP ax. Pressure Drop, bar [PSI ax. Oil Flow, lpm [GP i. Speed, [RP Pressure fluid O O Temperature rage, C[ F 2 Optimal Viscosity rage, mm /s [SUS Filtratio 96 [24.16 : 4,8 [ 611 :,6 [4921 8,6 [11. : [1 : 14 [ [1.2 ieral based- HLP(DIN 124) or H(ISO 674/4) -4 14 [-4 284 7 [ 98 47 ISO code /16 (i. recommeded fluid filtratio of 2 micro) Oil flow i drai lie Pressure drop bar [ PSI [ 14 14 [ Viscosity Oil flow i drai lie 2 mm /s [ SUS lpm [ GP [ 98 [ 164 [98 [164 2, [.66 1,8 [.476, [.92 2,8 [.74 p bar 2 1 p PSI 4 Pressure Losses 2 4 6 8 12 14 16 18 Q, GP 4 6 7 8 Q, lpm HT / E / 4 / 211 / E Pag. 9
PK otors SPECIFICATION DATA Type Displacemet, cm³/rev [ i³/rev ax. Speed, [RP ax. Torque [ ax. Output kw [ HP ax. Pressure Drop bar [ PSI ax. Oil Flow lpm [ GP ax. Ilet Pressure bar [ PSI ax. Retur Pressure with Drai Lie or ax. Pressure i Drai Lie, bar [ PSI ax. Startig Pressure with Uloaded Shaft, bar [ PSI i. Startig Torque, [ i. Speed***, [RP Weight, kg [ lb PK 49,[.2 88 7 [619 9,2 [814 PK 8 79,2 [4.8 6,8 [96 14,6 [1292 PK PK 12 Peak** 1,6 [1 21,4 [1894 26,1 [2 2,6 [288 41,8 [7 2,2 [46 1, [48 64, [691 8 [78,2 [7. 8,6 [11.,2 [7. 8,6 [11.,2 [7. 8,6 [11.,2 [7. 8,6 [11.,2 [7. 8,6 [11.,2 [7. 8,6 [11. 4,6 [6.2 7 [9.,4 [4.6,8 [7.8,4 [4.6,8 [7.8 [1 [1 [1 [1 [1 [1 9 [1 7 [1 7 [1 Peak** 14 [ 14 [ 14 [ 14 [ 21 [1 21 [1 21 [1 21 [1 14 [ 14 [ 21 [1 21 [1 11 [166 17 [247 [1 [1 17 [247 17 [247 4 [. [1.2 4 [. [1.2 4 [. [1.2 4 [. [1.2 4 [. [1.2 4 [. [1.2 4 [. [1.2 4 [. [1.2 4 [. [1.2 Peak** - RP 14 [ 14 [ 14 [ 14 [ 17 [24 17 [24 17 [24 17 [24 22 [26 22 [26 22 [26 22 [26 1 [218 1 [218 1 [218 1 [218 14 [ 14 [ 17 [24 17 [24 22 [26 22 [26 1 [218 1 [218 14 [ 17 [24 22 [26 1 [218 14 [ 14 [ 17 [24 17 [24 22 [26 22 [26 1 [218 1 [218 - RP -6 RP 7 [9 [72 7 [9 [72 7 [9 [72 7 [9 [72 7 [9 [72 7 [9 [72 7 [9 [72 7 [9 [72 7 [9 [72 >6 RP [29 [29 [29 [29 [29 [29 [29 [29 [29 -max. RP 1 [2 1 [2 1 [2 1 [2 1 [2 1 [2 1 [2 1 [2 1 [2 [14,8 [1 [11.1 [14 PK 16 PK PK 2 PK 1 PK 4 99 [6.4 12,8 [7. 18,4 [966 198 [12.1 247, [1.1 16,8 [19. 96 [24.16 44 2 4 22 1 2 22 16 2 126 17 126 14,4 [1274 17 [14 22 [1974 27, [244,1 [2664 1,7 [28 4,8 [611 18, [1619 22,9 [26 29, [29 6,6 [29 7,6 [28 44 [894,6 [4921 [14 [14 [14 [14 [14 [14 [14 9,1 [8 12,2 [79 14, [128 19, [172 24,8 [219 27, [24 29 [267,9 [278,1 [11.2, [11.7,4 [11.9,6 [12.,8 [12.8 6 [1.2 6, [1.9 6,8 [1 * Itermittet operatio: the permissible values may occur for max. % of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1 mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. Pag. 6 HT / E / 4 / 211 / E
PK otors DIENSIONS AND OUNTING DATA K Shaft ø82,±, [.248±.19 C Shaft CO Shaft SH Shaft SA Shaft L max 41,6±,2 [1.68±.79 14,±,4 [.71±.17 max [2.16 8±, [.1±.118 Port A ±, ±, [.787±.118 [.787±.118 max [2.16 11, [.4 22,8±,1 22,8±,1 [.898±.9 [.898±.9 Port B P (A,B) 2xø1, +,4 [.2 +.16 C,2 2 +, [.78+.78 L1 1,7±,1 1,7±,1 [1.2±.9 [1.2±.9 max ø88 [.464 T Type PK PK 8 PK PK 12 PK 16 PK PK 2 PK 1 PK 4 L, mm [i 2, 6, 9, 112, 117, 122, 129, 18, 149, [4.4 [4.19 [4.29 [4.4 [4.61 [4.82 [.8 [.4 [.87 L,mm 1 [i 6,67,67 1, 16,67 21, [.26 [.42 [.2 [.66 [.84 26,67 [1., [1.1 42,67 [1.68, [2.,2±,1 [2.94±.9 1 [.118,2±,1 [2.94±.9 max 96 [.779 [1.968 Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized -CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized -CW C P T (A, B) : 4x8-1 mm [.1 i depth : 2xG1/2 or 2x22x1, - 1 mm [.9 i depth : G1/4 or 14x1, - 8, mm [. i depth (plugged) mm [i HT / E / 4 / 211 / E Pag. 61
PK otors SHAFT EXTENSIONS C - ø2 straight, Parallel key A8x7x2 DIN 688 CO - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 ax. Torque 4 [ ax. Torque 4 [ 8 -,6 [.1 -.14 6,4 -, [.22 -.19 2 8 -, [ 1.2 -.118 ø28,6 [1.124 ø2 +,1 +,2 +.7 +.1 [.984 28,1 +,1 -,1 +.9 -.1 [ 1.6 ø28,6 [1.124 ø2,4 -,2 [ 1. -.8 8 mi 16 [.6 deep 4,2±, [1.7±.197 8 mi 16 [.6 deep 4,2±, [1.7±.197 SH - splied, BS 9 (SAE 6B) ax. Torque 4 [ 4 K - tapered 1:, Parallel key Bxx14 DIN 688 ax. Torque 4 [4 -,2 6,2 -, [.246-.19 8 mi 16 [.6 deep ø2,2±, [.997±.12 A-A -, [.197 -.11 24±,4 [.94 ±.16 1: A, [.87 S= Tighteig torque ±1 ø21,47±,7 [.84±.27 ø28,6 [1.124 mi 26,4 [1.9 4,2±, [1.7±.197 max 1,4 [.66 ø28,6±,1 [1.124±.88 A x1, ø4, [.177 ø [.196 ø44 [1.72 SA - splied, B2x22h9 DIN 482 ax. Torque 4 [4 ø28,6 [1.124 ø24, -,1 [.964 -.1 8 mi 16 [.6 deep 26,4±1 [1.9±.9 4,2±, [1.7±.197 mm [i PK 1 2 4 ORDER CODE Pos.1 - Displacemet code 8 12 16 2 1 4 Pos.2 - Shaft Extesios* C CO SH K SA - 49, cm /rev [.2 i /rev - 79,2 cm /rev [4.8 i /rev - 99, cm /rev [6.4 i /rev - 12,8 cm /rev [7. i /rev - 18,4 cm /rev [9.66 i /rev - 198, cm /rev [12. i /rev - 247, cm /rev [1. i /rev - 16,8 cm /rev [19. i /rev - 96, cm /rev [24.16 i /rev - ø2 straight, Parallel key A8x7x2 DIN688 - ø2,4 straight, Parallel key ¼"x¼"x1¼" BS46 - ø2,2 splied BS 9 (SAE 6B) - ø28,6 tapered 1:, Parallel key, Bxx14 DIN688 - ø24, splied B2x22h9 DIN 482 Pos. - Ports omit - BSPP (ISO 228) - etric (ISO 262) Pos. 4 - Special Features (see page 99) Pos - Desig Series omit - Factory specified NOTE: * The permissible output torque for shafts must be ot exceeded! The hydraulic motors are magao-phosphatized as stadard. 11 Pag. 62 HT / E / 4 / 211 / E
Hydraulic otors RK Series APPLICATION»»»» Coveyors Feedig mechaism of robots ad maipulators etal workig machies Textile machies» Agriculture machies» Food idustries» iig machiery etc. CONTENTS Specificatio data... 64 Dimesios ad moutig... 6 Shaft extesios... 66 Order code... 66 OPTIONS» odel- Spool valve, gerotor» Atifrictio coical bearig» Flage mout» Shafts- straight, splied ad tapered» etric ad BSPP ports» Other special features GENERAL ax. Displacemet, cm /rev [i /rev ax. Speed, [RP ax. Torque, [ ax. Output, kw [HP ax. Pressure Drop, bar [PSI ax. Oil Flow, lpm [GP i. Speed, [RP Pressure fluid O O Temperature rage, C[ F 2 Optimal Viscosity rage, mm /s [SUS Filtratio 97 [24.4 97 : 4 [ 4 : [442 12,8 [17.2 : 14 [ : 17 [24 7 [18. ieral based- HLP(DIN 124) or H(ISO 674/4) -4 14 [-4 284 7 [ 98 47 ISO code /16 (i. recommeded fluid filtratio of 2 micro) Oil flow i drai lie Pressure Losses Pressure drop bar [ PSI [ 14 14 [ Viscosity Oil flow i drai lie 2 mm /s [ SUS lpm [ GP [ 98 [ 164 [98 [164 2, [.66 1,8 [.476, [.92 2,8 [.74 p bar 2 1 p PSI 4 2 4 6 8 12 14 16 18 Q, GP 4 6 7 8 Q, lpm 11 HT / E / 4 / 211 / E Pag. 6
RK otors SPECIFICATION DATA Type RK RK 8 RK Displacemet, cm³/rev [ i³/rev 1, [.14 8, [4.9 99,8 [6.9 12,[7.67 19,6[9.74 199,8[12.192,1[1.26 1,7[19.26 97 [24.4 ax. Speed, [RP 77 97 7 94 6 7 47 6 7 47 7 24 19 24 1 18 ax. Torque [8 1,7 [19 19,8 [17 2 [22 2 [28 4 [ 4 [4 4 [4 4 [4 [ 1 [11 19, [172 24 [212 [26 9 [4 42 [717 47 [416 [442 [442 Peak** 17 [1 27 [29 2 [28 7 [27 46 [47 6 [496 64 [66 6 [7 6 [7 ax. Output 9 [12.1,4 [1.9,8 [14.4,8 [14.4,4 [1.9 8,8 [11.8 8,1 [.9 7,4 [9.9 6,2 [8. kw [ HP ax. Pressure Drop bar [ PSI,4 [1.9 12,6 [16.9 12,8 [17.2 12, [16.8 11, [1.4,2 [1.7 14 [ 14 [ 14 [ 14 [ 14 [ 12 [18 17 [24 17 [24 17 [24 17 [24 17 [24 1 [22 9,4 [12.6 1 [16 14 [ 7,8 [. [1 12 [18 7,1 [9. 7 [9 9 [1 Peak** 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 [29 1 [217 1 [174 ax. Oil Flow lpm [ GP 4 [. [1.2 6 [1.9 7 [18. 6 [1.9 7 [18. 6 [1.9 7 [18. 6 [1.9 7 [18. 6 [1.9 7 [18. 6 [1.9 7 [18. 6 [1.9 7 [18. 6 [1.9 7 [18. ax. Ilet Pressure bar [ PSI ax. Retur Pressure Peak** - RP 17 [24 17 [24 17 [24 17 [24 17 [24 17 [24 [29 [29 [29 [29 [29 [29 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 1 [218 1 [218 1 [218 1 [218 1 [218 1 [218 17 [24 [29 22 [26 1 [218 17 [24 17 [24 [29 [29 22 [26 22 [26 1 [218 1 [218 with Drai Lie or ax. Pressure i - RP -6 RP 7 [9 [72 7 [9 [72 7 [9 [72 7 [9 [72 7 [9 [72 7 [9 [72 7 [9 [72 7 [9 [72 7 [9 [72 Drai Lie, bar [ PSI >6 RP [29 [29 [29 [29 [29 [29 [29 [29 [29 -max. RP 1 [2 1 [2 1 [2 1 [2 1 [2 1 [2 1 [2 1 [2 1 [2 ax. Startig Pressure with Uloaded Shaft, bar [ PSI [14 [14 [14 [14 [14 [14 [14 [14 [14 i. Startig Torque, [ 8 [7 12 [6 16 [14 [177 2 [221 29 [27 28 [248 2 [282 [ i. Speed***, [RP Weight, kg [ lb 6,2 [1.7 6, [1.9 6,6 [14.6 6,7 [14.8 6,9 [1.2 7,4 [16. 7,8 [17.2 8, [18.7 9, [. RK 12 RK 16 RK RK 2 RK 1 RK 4 * Itermittet operatio: the permissible values may occur for max. % of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1 mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. Pag. 64 HT / E / 4 / 211 / E
Oval out (2 Holes) Q - Square out (4 Bolts) ø82,±, [.248±.19 max [2.87 2xø1, +,4 [.2 +.16,7±,1 [1.4±.9 C 17±,1 Port A Port B 2,±,2 ±,1 16 [.6 [1.181±.9 6,4 max [.22 44±,2 P (A,B),2±,1 [2.94±.9 67±,2 [2.68±.79 max ø [ 4,14 T 1 [.118,2±,1 [2.94±.9 4x mi 1 mm [.1 i deep max 82 [.228 max 8 [4.22 max 8 [ 4,2 2 42, [1.67 RK otors DIENSIONS AND OUNTING DATA SH Shaft SA Shaft CO Shaft K Shaft C Shaft K Shaft ø44,4±, [1.748±.19 C Shaft SH Shaft SA Shaft CO Shaft 49,2 max [1.94 2,±, [.98±.118 L max [.669±.9 [.92±.79 L max 4±,1 [1.7±.9 17±,1 [.669±.9 Port A Port B 2,±,2 C [.92±.79 ±,1 [1.181±.9 L1 [1.72±.79 L1 44±,2 [1.72±.79 P (A,B) 67±,2 [2.68±.79 max ø [ 4,14 T [1.968 ø82,±,1 [.2±.9 [2.16 C P T (A, B) : 4x8-1 mm [.1 i depth : 2xG1/2 or 2x22x1, - 1 mm [.9 i depth : G1/4 or 14x1, - 8, mm [. i depth (plugged) Stadard Rotatio Reverse Rotatio Viewed from Shaft Ed Viewed from Shaft Ed Port A Pressurized - CW Port A Pressurized - CCW Port B Pressurized -CCW Port B Pressurized -CW mm [i Type RK RK RK RK RK RK RK RK RK 8 12 16 2 1 4 L, mm [i Type L, mm [i 9,[4.1 RKQ 11,8 [4.48 114,[4.1 RKQ 8 118,8 [ 4.68 118,[4.6 RKQ 122, [ 4.82 122,[4.82 RKQ 12 126,8 [ 4.99 128,[.6 RKQ 16 12,8 [.2 1,[. RKQ 19,8 [. 144,[.67 RKQ 2 148, [.84 1,[6.12 RKQ 1 19,8 [ 6.29 17,[6.69 RKQ 4 174, [ 6.86 L,mm 1 [i 9, 14, 17,4 21,8 27,8 4,8 4, 4,8 69,4 [. [. [.69 [.86 [1.9 [1.7 [1.71 [2.16 [2.7 HT / E / 4 / 211 / E Pag. 6
RK otors SHAFT EXTENSIONS C - ø2 straight, Parallel key A8x7x2 DIN 688 CO - ø1" straight, Parallel key ¼"x¼"x1¼" BS46 ax. Torque 4 [ ax. Torque 4 [ 8 -,6 [.1 -.14 6,4 -, [.22 -.19 2 8 -, [ 1.2 -.118 ø28,6 [1.124 ø2 +,1 +,2 +.7 +.1 [.984 28,1 +,1 -,1 +.9 -.1 [ 1.6 ø28,6 [1.124 ø2,4 -,2 [ 1. -.8 8 mi 16 [.6 deep 4,2±, [1.7±.197 SH - splied, BS 9 (SAE 6B) ax. Torque 4 [ 4 8 mi 16 [.6 deep 4,2±, [1.7±.197 K - tapered 1:, Parallel key Bxx14 DIN 688 ax. Torque 4 [4 -,2 6,2 -, [.246-.19 8 mi 16 [.6 deep ø2,2±, [.997±.12 A-A -, [.197 -.11 24±,4 [.94 ±.16 1: A, [.87 S= Tighteig torque ±1 ø21,47±,7 [.84±.27 ø28,6 [1.124 mi 26,4 [1.9 4,2±, [1.7±.197 max 1,4 [.66 ø28,6±,1 [1.124±.88 A x1, ø4, [.177 ø [.196 ø44 [1.72 SA - splied, B2x22h9 DIN 482 ax. Torque 4 [4 ø28,6 [1.124 ø24, -,1 [.964 -.1 8 mi 16 [.6 deep 26,4±1 [1.9±.9 4,2±, [1.7±.197 mm [i ORDER CODE RK 1 2 4 6 Pos.1 - outig Flage omit - Oval mout, two holes Q -Square mout, four bolts Pos.2 - Displacemet code 8 12 16 2 1 4-1, cm /rev [.14 i /rev - 8, cm /rev [4.9 i /rev - 99,8 cm /rev [6.9 i /rev - 12,7 cm /rev [7.67 i /rev - 19,6 cm /rev [9.74 i /rev - 199,8 cm /rev [12.19 i /rev - 2,1 cm /rev [1.26 i /rev - 1,7 cm /rev [19.26 i /rev - 97, cm /rev [24.4 i /rev Pos. - Shaft Extesios* C CO SH K - ø2 straight, Parallel key A8x7x2 DIN688 - ø2,4 straight, Parallel key ¼"x¼"x1¼" BS46 - ø2,2 splied BS 9 (SAE 6B) - ø28,6 tapered 1:, Parallel key, Bxx14 DIN688 SA - ø24, splied B2x22h9 DIN 482 Pos.4 - Ports omit - BSPP (ISO 228) - etric (ISO 262) Pos. - Special Features (see page 99) Pos.6 - Desig Series omit - Factory specified NOTE: * The permissible output torque for shafts must be ot exceeded! The hydraulic motors are magao-phosphatized as stadard. Pag. 66 HT / E / 4 / 211 / E
Hydraulic otors RW Series APPLICATION» Coveyors» Feedig mechaism of robots ad maipulators» etal workig machies» Textile machies» Agriculture machies» Food idustries» Grass cuttig machiery etc. CONTENTS Specificatio data... 68 Fuctio diagrams...69 7 Dimesios ad moutig... 74 Permissible shaft Seal Pressure... 7 Permissible shaft loads... 7 Shaft extesios... 76 Order code... 76 OPTIONS»»»»»» odel- Spool valve, roll-gerotor Wheel mout Shafts- straight ad tapered Shaft seal for high ad low pressure etric ad BSPP ports Other special features GENERAL ax. Displacemet, cm /rev [i /rev ax. Speed, [RP ax. Torque, [ ax. Output, kw [HP ax. Pressure Drop, bar [PSI ax. Oil Flow, lpm [GP i. Speed, [RP Pressure fluid O O Temperature rage, C[ F 2 Optimal Viscosity rage, mm /s [SUS Filtratio 97 [ 24.4 29 : 61 [ 4 : 69 [6 1 [.1 : 17 [ 24 : [29 9 [2.8 ieral based- HLP(DIN 124) or H(ISO 674/4) -4 14 [-4 284 7 [ 98 47 ISO code /16 (i. recommeded fluid filtratio of 2 micro) Pressure drop bar [ PSI [ 14 14 [ Oil flow i drai lie Viscosity 2 mm /s [ SUS [ 98 [ 164 [98 [164 Oil flow i drai lie lpm [ GP 2, [.66 1,8 [.476, [.92 2,8 [.74 p bar 2 1 p PSI 4 Pressure Losses 2 4 6 8 12 14 16 18 Q, GP 4 6 7 8 Q, lpm HT / E / 4 / 211 / E Pag. 67
RW otors SPECIFICATION DATA Type Displacemet, cm³/rev. [ i³/rev. ax. Speed, [RP ax. Torque [ Peak** ax. Output kw [ HP ax. Pressure Drop bar [ PSI Peak** ax. Oil Flow lpm [ GP ax. Ilet Pressure bar [PSI Peak** ax. Retur Pressure with Drai Lie bar [PSI Peak** ax. Startig Pressure with Uloaded Shaft, bar [PSI i. Startig Torque At max.press. [ drop At max.press. drop i. Speed***, [RP Weight, kg [ lb RW 1, [.14 77 29 [9 1 [11 17 [1 7 [9. 8, [11.9 14 [ 17 [24 22 [26 4 [,6 [1,2 17 [24 [29 22 [26 17 [24 [29 22 [26 [14 8 [7 [88 9,6 [21.2 RW 8 8, [4.9 7 94 [177 22 [1947 27 [29 12, [17 1 [.1 17 [24 [29 22 [26 6 [1,9 7 [19,8 17 [24 [29 22 [26 17 [24 [29 22 [26 [14 RW 99,8 [6.9 6 7 RW 12 12,7 [ 7.67 47 6 24 [212 [ 26 28 [248 4 [ 2 [282 7 [ 27 1 [17.4 12, [ 16.8 1 [.1 14, [ 19. 17 [24 17 [24 [29 [29 22 [26 22 [26 6 [1,9 7 [19,8 6 [1,9 7 [19,8 RW 16 19,6 [9.74 7 47 9 [4 4 [8 46 [47 11, [1.4 14 [18.8 17 [24 [29 22 [26 6 [1,9 7 [19,8 17 [24 17 [24 17 [24 17 [24 17 [24 17 [24 17 [24 [29 [29 [29 [29 [29 [29 [29 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 17 [24 17 [24 17 [24 17 [24 17 [24 17 [24 17 [24 [29 [29 [29 [29 [29 [29 [29 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 22 [26 [14 9 [ 1 7 [2 RW RW 2 RW 1 RW 4 199,8 2,1 1,7 97 [ 12.19 [1.26 [19.26 [24.4 24 19 7 6 28 226 4 [ 4 4 [478 [487 61 [4 [ 442 61 [4 69 [6 69 [6 6 [ 496 71 [628 84 [74 87 [77 11 [ 14.8 [1.4 9 [12 7,8 [. 1 [ 17.4 12 [16.1 [1.4,6 [14.2 17 [24 17 [24 1 [196 1 [16 [29 [29 17 [24 14 [ 22 [26 22 [26 2 [4 17 [24 6 [1,9 7 [19,8 [ 7 7 [19,8 9 [2.8 [7 7 [19,8 9 [2.8 [7 7 [19,8 9 [2.8 [7 1 [1 [177 2 [ 221 2 [282 41 [ 6 [442 [442 [442 17 [1 9,7 [21.4 2 [ 9.8 [21.7 28 [ 248, [ 22.1 7 [27, [22.7 46 [ 47,8 [ 2.8 [487 11, [24.9 66 [84 11,8 [26 61 [4 12, [27.6 * Itermittet operatio: the permissible values may occur for max. % of every miute. ** Peak load: the permissible values may occur for max. 1% of every miute. *** For speeds lower tha give, cosult factory or your regioal maager. 1. Itermittet speed ad itermittet pressure must ot occur simultaeously. 2. Recommeded filtratio is per ISO clealiess code /16. A omial filtratio of 2 micro or better.. Recommed usig a premium quality, ati-wear type mieral based hydraulic oil HLP(DIN124) or H ( ISO 674/4). If usig sythetic fluids cosult the factory for alterative seal materials. 4. Recommeded miimum oil viscosity 1 mm²/s [7 SUS at C [122 F.. Recommeded maximum system operatig temperature is 82 C [18 F. 6. To assure optimum motor life fill with fluid prior to loadig ad ru at moderate load ad speed for -1 miutes. Pag. 68 HT / E / 4 / 211 / E
RW otors RW FUNCTION DIAGRAS 1 9 8 7 6 4 12 11 9 8 7 6 4 2 1 it. Q= 1. GP 2.6 GP GP 1 4.,kW GP. 1kW 2 6.6 GP 2kW 7.9 GP 9.2 GP 4kW 4.6 GP 6kW 8kW 4 11.9 GP 1.2 GP p=17 bar 24 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 7 bar PSI bar 7 PSI bar 4 PSI 4 6 7 8 9 RP RW 8 Q= 1. GP 2.6 GP. GP GP 7.9 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 18 22 p= bar 29 PSI 16 14 8 6 4 18 16 14 12 8 6 4 2 4 6 7 8 9 RP 17 bar 24 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI bar 4 PSI The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. HT / E / 4 / 211 / E Pag. 69
RW otors RW FUNCTION DIAGRAS Q= 1. GP 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP GP 6 1.9 7 18. GP 7 19.8 GP 2 28 1 24 16 12 it. p= bar 29 PSI 17 bar 24 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 8 bar 116 PSI 4 6 bar 87 PSI bar 4 PSI 4 6 7 RP RW 12 Q= 1. GP 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 6 28 24 16 8 4 2 p= bar 29 PSI 28 17 bar 24 PSI 24 16 12 8 4 c ot. it. 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI bar 4 PSI 4 6 RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. Pag. 7 HT / E / 4 / 211 / E
RW otors RW 16 FUNCTION DIAGRAS 4 44 Q= 1. GP 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP GP 7 19.8 6 28 24 16 8 4 6 2 28 24 16 12 8 it. p= bar 29 PSI 17 bar 24 PSI 14 bar PSI 1 bar 174 PSI bar 14 PSI 8 bar 116 PSI 6 bar 87 PSI 4 4 1 2 4 4 bar 4 PSI RP RW Q= 1. GP 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 4 4 2 1 4 4 2 1 it. p= bar 29 PSI 17 bar 24 PSI 14 bar PSI 1 bar 174 PSI bar 1 PSI 8 bar 116 PSI 6 bar 87 PSI 1 2 bar 4 PSI RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. HT / E / 4 / 211 / E Pag. 71
RW otors RW 2 FUNCTION DIAGRAS 6 4 4 6 6 4 Q= 1. GP it. 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP GP 6 1.9 7 18. GP 7 19.8 GP 9 2.8 GP p= bar 29 PSI 17 bar 24 PSI 2 1 4 2 1 14 bar PSI 1 bar 16 PSI bar 1 PSI 8 bar 116 PSI 6 bar 87 PSI bar 4 PSI 2 7 12 1 17 22 2 27 2 7 RP RW 1 6 6 4 4 2 72 64 6 48 4 2 24 Q= 1. GP it. 2.6 GP. GP 7.9 GP 4.6 GP 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 9 2.8 GP p=17 bar 24 PSI 16 bar 2 PSI 1 bar 174 PSI 12 bar 18 PSI 8 bar 116 PSI 1 16 8 The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. 6 bar 94 PSI 4 bar 6 PSI bar 4 PSI 2 7 12 1 17 22 2 27 RP Pag. 72 HT / E / 4 / 211 / E
RW otors FUNCTION DIAGRAS RW 4 6 48 44 4 6 28 24 16 8 4 64 6 6 2 48 44 4 6 2 28 24 16 12 8 4 Q= 1. GP 2.6 GP GP 1 4. GP. 7.9 GP GP 4.6 1.2 GP 6 1.9 GP 7 18. GP 7 19.8 GP 4 6 7 8 9 1 1 1 14 1 16 17 18 19 9 2.8 GP 2 2 2 p=12 bar 18 PSI 1 bar 16 PSI 9 bar 1 PSI 8 bar 116 PSI 6 bar 94 PSI bar 8 PSI 4 bar 8 PSI bar 4 PSI RP The fuctio diagrams data is for average performace of radomly selected motors at back pressure o bar [72. 14 PSI ad oil with viscosity of 2 mm²/s [1 SUS at C [122 F. HT / E / 4 / 211 / E Pag. 7
RW otors DIENSIONS AND OUNTING DATA KB Shaft CB Shaft OB Shaft +, ø82, [.2 +.19 8±, [2.28±.12 Shaft Dim. See Page 76 18,±,2 [.7±.79 6,8±, [1.4±.12 max 7 [4.21 Port A Port B 47,1±,2 [1.8±.79 9,4 -, [.7 -. 2±,1 [.9±.6 2±,1 [.9±.6 P (A,B) ø127 -,4 [4.99-.16 L1 L max ±, [.9±. ø [.94 T Type L, mm [ i L, 1 mm [ i RW 8, [ 4.2 9, [. RW 8 11, [ 4.4 14, [. RW 116, [ 4.9 RW 12 1, [ 4.74 17,4 [.69 21,8 [.86 RW 16 126, [ 4.98 27,8 [ 1.9 RW 1, [.26 4,8 [ 1.7 RW 2 142, [.61 4, [ 1.71 RW 1 1, [ 6.4 4,8 [ 2.16 RW 4 168, [ 6.6 69,4 [ 2.7 4 o 1 [.118 64 [2.2 12 [.197 4ø1,±,2 [.±.79 ø147±,2 [.787±.79 P (A,B): T : 2xG1/2 or 2x22x1, - 17 mm [.67 i. depth G1/4 or 14x1, - 12 mm [.47 i. depth (plugged) Stadard Rotatio Viewed from Shaft Ed Port A Pressurized - CW Port B Pressurized -CCW Reverse Rotatio Viewed from Shaft Ed Port A Pressurized - CCW Port B Pressurized -CW mm [i Pag. 74 HT / E / 4 / 211 / E
RW otors AX. PERISSIBLE SHAFT SEAL PRESSURE RW...; RW...UK motors with drai coectio: The shaft seal pressure equals the pressure i the drai lie. RW...1 motors without drai coectio: The shaft seal pressure ever exceeds the pressure i the retur lie. R W...U motors with high pressure seal ad drai coectio: The shaft seal pressure equals the pressure i the drai lie. ax. retur pressure without drai lie or max. pressure i the drai lie P PSI 2 1 P bar 2 1 1 2 4 6 7 8 RP 1: Drawig for Stadard Shaft Seal 2 : Drawig for High Pressure Seal ("U" Seal) - cotiuous operatios - itermittet operatios PERISSIBLE SHAFT LOADS The curve applies to a B bearig life of hours. Pr dan 2 1 4 2 1-1 i dan 67 lbs dan 67 lbs 1 2 4 Pr lbs. 7 6 4 1. Permissible radial shaft load 2. Drawig by = rpm. Drawig by = rpm 4. Drawig by = rpm. Drawig by =4 rpm 1 8 6 4 - mm HT / E / 4 / 211 / E Pag. 7
- RW otors SHAFT EXTENSIONS ø2 +,18 +,2 CB - ø2 straight, Parallel key Ax8x4 DIN 688 ax. Torque 77 [681 +.7 +.8 [1.26 8 16 [.6 8±, [2.28±.12 ø [1.8 -,6 [.9-.1 -,2 [ 1.8 -.79 S=41 Tighteig Torque ±1 [177±9 ø44 [1.7 ø4, [.177 KB - tapered 1:, Parallel key B6x6x DIN 688 ax. Torque 77 [681 x1, [.196 A A 6±, [1.42±.19 8±, [2.28±.12 ø -,9 [ -.1 1.8 Taper 1: A-A 19,1-,1 [.7 -.9 6-, [.24 -.12 OB - tapered 1:8 SAEJ 1, Parallel key "x 16 16 "x1¼" BS46 ax. Torque 77 [681 S=1 7/ 16 " Tighteig Torque B-B ±1 7.96 -,2 [177±9 B [1.1-.8 17 +,16 6, +.6 -.24 [.67 1-UNEF ø4 [.17 [.196 B [1.8 4±, [2.1±.12 8±, [2.28±.12 ø1,77-, [ 1.2 -.19 ø [1.8 Taper 1:8 mm [i ORDER CODE CB KB OB RW 1 2 4 6 Pos.1 - Displacemet code 8 12 16 2 1 4-1, cm /rev [.14 i /rev - 8, cm /rev [4.9 i /rev - 99,8 cm /rev [6.9 i /rev - 12,7 cm /rev [7.67 i /rev - 19,6 cm /rev [9.74 i /rev - 199,8 cm /rev [12.19 i /rev - 2,1 cm /rev [1.26 i /rev - 1,7 cm /rev [19.26 i /rev - 97, cm /rev [24.4 i /rev Pos.2 - Shaft Extesios * - ø2 straight, Parallel key Ax8x4 DIN688 - ø tapered 1:, Parallel key B6x6x DIN6888 1 -ø1/" 4 tapered1:8, Parallel key "x 16 16 "x1¼" BS46 7 Pos. - Shaft Seal Pressure omit U UK - Stadard shaft seal - High pressure shaft seal without check valves - High pressure shaft seal with check valve Pos.4 - Drai Port omit 1 - with drai port - without drai port Pos. - Ports omit - BSPP (ISO 228) - etric (ISO 262) Pos.6 - Special Features (see page 99) Pos.7 - Desig Series omit - Factory specified NOTE: * The permissible output torque for shafts must ot be exceeded! The hydraulic motors are magao-phosphatized as stadard. Pag. 76 HT / E / 4 / 211 / E
Hydraulic otors H Series APPLICATION» Coveyors» Feedig mechaism of robots ad maipulators» etal workig machies» Textile machies» Agriculture machies» Food idustries» iig machiery etc. CONTENTS Specificatio data... 78 Fuctio diagrams... 79 81 Permissible shaft loads... 81 Dimesios ad moutig... 82 Permissible shaft seal pressure... 8 Shaft extesios... 84 Order code... 84 OPTIONS» odel- Spool valve, roll-gerotor» Flage mout» Shafts- straight, splied ad tapered» etric ad BSPP ports» Other special features GENERAL ax. Displacemet, ax. Speed, ax. Torque, ax. Output, ax. Pressure Drop, ax. Oil Flow, i. Speed, Pressure fluid Temperature rage, cm /rev [i /rev [RP [ kw [HP bar [PSI lpm [GP [RP O C[ F 2 Optimal Viscosity rage, mm /s [SUS Filtratio O 2,4 [.7 44 : 84 [ 744 : 4 [94 18, [24.8 : 17 [ 24 : [29 9 [ 2.78 ieral based- HLP(DIN 124) or H(ISO 674/4) -4 14 [-4 284 7 [ 98 47 ISO code /16 (i. recommeded fluid filtratio of 2 micro) Oil flow i drai lie Pressure Losses Pressure drop bar [ PSI [ 14 14 [ Viscosity Oil flow i drai lie 2 mm /s [ SUS lpm [ GP [ 98 [ 164 [98 [164 2, [.66 1,8 [.476, [.92 2,8 [.74 18 16 14 12 8 6 4 2 2 1 2 4 6 8 12 14 16 18 22 24GP 4 6 7 8 9 lpm HT / E / 4 / 211 / E Pag. 77