INVITATION TO BID Sealed bids will be received by the Kent County Road Commission, 1500 Scribner Avenue NW, Grand Rapids, Michigan 49504 until Thursday, March 21, 2019, 8:30 AM deadline, at which time they will be publicly opened and read in the H.T. Conference Room for: Purchase of One (1) Five-Axle Heavy Duty Cab and Chassis Truck - 74,000# GVW All bids are to be in sealed envelopes and plainly marked as to the equipment, material, or service being bid upon and the name of the Bidder. The Board reserves the right to reject any and all Proposals or to waive irregularities therein, and to accept any Proposals which, in the opinion of the Board, may be most advantageous and to the best interest of the County. BOARD OF COUNTY ROAD COMMISSIONERS OF THE COUNTY OF KENT By: Mark E. Rambo, Chairman ----------------------------------------------------------------------------------------------------------- PLEASE ACKNOWLEDGE RECEIPT OF THIS INVITATION TO BID AND FAX BACK TO 616.242.6980. Company Authorized Signature Date
INSTRUCTION TO BIDDERS Sealed bids will be publicly opened at the offices of the Board of County Road Commissioners of the County of Kent, State of Michigan, located at 1500 Scribner Avenue NW, Grand Rapids, MI 49504. Refer to the INVITATION TO BID for the exact timing and for the identification of the bids as related to furnishing materials, services, equipment, work and/or supplies with the terms, conditions, specifications, drawings, plans, and special provisions as stated herein and hereto attached. The Board's normal practice is to open and read the bids then refer the file to Staff for tabulation and analysis. During this period, the files are closed until this action is complete. Generally, this involves three or four days depending upon the nature of the bid. Copies of the bid tabulations are made available only after this time and upon request to the Purchasing Department, by mail or phone (616) 242-6928. 1. All bids must be submitted on the Board's bid blank form when provided. The bid shall be legibly prepared in ink or typewriter. Erasures or alterations must be initialed by the bidder. 2. Specifications and plans should not be returned with bid unless otherwise stated herein. 3. Bid shall be mailed or delivered. It shall be in a sealed envelope and identified on the outside as to the bid concerned. If a printed label is enclosed, bidders are requested to complete it and attach it to the envelope. 4. Bids will not be accepted after the time designated for the opening of the bids. The bidder shall assume full responsibility for delivery of bids prior to the appointed hour for opening same and shall assume the risk of late delivery or non-delivery regardless of the manner he/she employs for the transmission thereof. Bids will be accepted at the Purchasing Department on behalf of the Board at any time during normal business hours only, said hours being 7:30 AM to 4:00 PM Mondays through Fridays, legal holidays excepted. 5. It is understood that the Board of County Road Commissioners is a Governmental unit and as such, is exempt from the payment of all State and Federal taxes, except as allowed by the regulatory agencies to be included in the cost of materials and services. 6. The bidder, by execution of the bid proposal, thereby declares that the bid is made without collusion with any other person, firm, or corporation, and agrees to furnish all bid items in strict adherence with all Federal regulatory measures. 7. The Board reserves the right to reject any and all bids, to waive any irregularities therein, and to accept any bid which, in the opinion of the Board, may be most advantageous and to the best interest of the County. In case of error in the extension of prices in the bid or other arithmetical error, the unit prices will govern.
Specifications For Heavy Duty 5-Axle Cab and Chassis Truck It is the intent of the Kent County Road Commission to purchase one 5-axle truck cab and chassis. A. Intended Use: General Specifications 1. This equipment will have a live bottom end discharge, 22 yard capacity body, installed by the KCRC. 2. They will be fitted with an underbody scraper in place of the one pusher axle in the winter to: a. Haul and spread snowmelt material b. Clean roads c. Haul road materials (gravel, sand, bituminous) B. Make and Model: 1. Peterbilt 367 2. Kenworth T-800 3. Must be new and current model in production 4. Specifications should be viewed as minimum requirements 5. Alternate bids will not be accepted or read without prior authorization from Steve Roose, Director of Equipment. If you have a product that you feel is an alternate to the product specified, contact Steve at 616/481-5368 for consideration of such product as soon as possible and prior to the bid opening. C. Purchase Terms: D. Price: Normal Purchase Terms (Lump Sum Payment) F.O.B. Kent County Road Commission - Central Complex 1500 Scribner Avenue N.W. Grand Rapids, MI 49504 (less all state and federal taxes) E. Award of Bid Criteria / Quantity: 1. Bids will be evaluated by the Equipment Module Division. The award of the bid will not be based solely on low bid but will take into consideration equipment cost, equipment meeting or exceeding specified requirements, delivery dates as specified and taking into consideration the equipment value that is in the best interest of the Road Commission. 2. Upon award of bid, quantity ordered might increase, but the unit bid cost will prevail. The right is reserved by the Road Commission to allow other governmental agencies to piggy back onto this bid.
2 F. Delivery: 1. ASAP 2. No payment will be made until equipment has been delivered, inspected, approved and receipt of RD108. 3. RD108E must indicate in the Body Style Dump and in the Remarks section Tax Exempt Municipal Title delivered on Dealer Plate. G. Literature: 1. Enclose literature on unit 2. Must be supplied upon delivery: a. One factory type service, repair and electric diagram manuals for chassis and engine b. One software for the engine and antilock, compatible with a lap top computer. H. Warranty: ALL WARRANTIES TO START AT K.C.R.C. IN-SERVICE DATE! Provide a menu including cost and terms for extended warranties on all major components of the vehicle up to and including 5 years duration. Including but not limited to Body, Engine, Transmission, and Differential. I. Bid Form: 1. Bid must be submitted on bid blank and detailed in its entirety or bid may be rejected. 2. These specifications are to be met to the best ability of the Manufacturer and Dealer, and any deviations from these specifications must be stated clearly on the bid blank. 3. Place a check mark x, or write yes if your bid meets specifications. Only deviations from the specifications should be detailed on the bid form.
3 Technical Specifications/Bid Form *Make *Model *GVW *Year Cab: *Wheelbase *Cab To Axle *AF Model: Conventional, with tractor package providing trailer hook up for air brakes and lights at rear of truck. Truck to be supplied to us with two steerable lifting pushers, one lifting tag axle and tandem drive axles Bidder is responsible for proper spacing of axles for intended use of vehicle. Meets Specs Deviations KCRC Rec d Gross Vehicle Weight: 74,000# minimum Cab: Wheel base 252 Cab to axle 175 nominal (these measurements may vary by chassis mfg.) Must allow mounting of Red River 24 overhang from rear of rear-most tire to end of frame Frame (Single Frame): Size of section, crossmembers and reinforcing to be equal to specified GVW, 120000 psi, steel, 10-3/4 x 3/8 with ¼ full liner, 3,468,000 RBM Must not interfere with body mounting, or underbody scraper mounting 20" front frame extension for plow mounting Ground clearance to permit mounting and operation of underbody scraper in place of two pusher axles Engine & Equipment: 455 horsepower @ 1650 ft.lbs. torque 13 liter or greater Must be EPA certified, using selective catalytic reduction
4 Engine equipment: All standard equipment including but not limited to Engine compression brake Volt meter Tachometer Hour meter Oil pressure and water temp gauges Warning lights with alarm Automatic shutdown and rest system Speedometer with odometer reading in tenths Filters: Coolant filter, spin on type Under hood, dry type air filter with restriction gauge Fuel/water separator, spin on type Fuel filter, spin on type Oil filter, two 1-1/2 quart full flow, or one 2.6 quart combination full flow with bypass 2 stage fan clutch Low coolant sensor Magnetic drain plug Electronic start and shut down Electronic RPM/PTO operation Manual fuel pump primer Fuel Tanks One right Under cab 80 U.S. gallon minimum Aluminum material With removal by the Road Commission of the two pusher axles, this outside area of frame rail must be free of obstruction to facilitate the mounting of an underbody scraper. Transmission: Allison automatic transmission 4500 6 speed RDS [Package 113] Dash mounted push button controller with snowplow programming Front Axle and Suspension: Set back axle 20,000 lb.
5 Dual hydraulic power steering, with TAS 85 Dual TRW Compatible with GVW Taper leaf spring Oil lube hubs with Stemco #348-409 hub cap Front shocks Heavy duty iron front spring brackets Rear Axle and Suspension: 46,000 lb. Meritor RT-46-160- P with driver controlled locking differential on both axles of tandem, with warning light, cab operated interaxle differential lock up control with warning light Must have heavy wall and lube pump included Gear ratio to equal 65 MPH at peak torque or fuel efficiency (4.56) Proper gearing to plow at 35 MPH Magnetic drain and fill plugs Synthetic lube Oil lube hubs and seals 46,000 lb. Neway AD246 air ride suspension or Air Trac 46,000 lb. suspension Drive axle suspension to be Huck bolted Steerable Pusher Lift Axle (2) and One (1) Rear Tag: Watson-Chalin SL1190 SSR tandem pushers or equivalent Watson-Chalin AL2200 non-steer lift tag or equivalent Air lift/air ride 22.5 x 8.25 set up for hub pilot Dust shields for brakes 16.5 x 7 brakes Type 30 brake chambers, parking brake on all axles In cab control kit (gauges & regulators) Vertical ride shock kit Automatic reverse lifting Auxiliary air supply tank and brake relay for each axle Include tires and rims for 11R22.5 tires Oil lube hubs and seals Pusher & tag axles to be bolted on to facilitate removal and installation of underbody scraper
6 Brakes: On all axles Air brakes, S cam drum type, on all axles Front, 16.5 x 7 Rear, 16.5 x 7 Outboard brake drums, iron Automatic slack adjusters 25.9 cu. foot air compressor minimum Air tanks not to interfere with dump body or underbody scraper Parking brake Heated air dryer, Bendix AD-IS orwabco SS-1200 Plus Dust shields on all brakes Wheels, Drive and Steer: 22.5 x 8.25, hub pilot, heavy duty accuride disc, color grey, steel, 8,000 lb. load rated. Front wheels 22.5 x 12.25, hub pilot, heavy duty accuride disc, aluminum 12500 lb. load rated. Steel wheels on all other axles Tires: Front, 385/65 Goodyear G-296 Drive, 11R22.5 Goodyear LRH G741 MSD or Michelin XDS2 Lift axle, 11R22.5 Goodyear with 22.5 x 8. 25 steel wheel Steel belted radials, all Driveline: Universal joints, drive shafts, etc. to match GVW rating and allow clearance for underbody scraper in place of two pusher axles. SPL 250 drive line does not have ½ moon caps Radiator: Heavy duty, cross flow, increased cooling type, matched to engine size Compatible with live power take off at front of engine, without radiator cut out for clearance Stationary grill/guard (not to tilt with hood/fenders) Drain cock Long life coolant Power Take Off:
7 For live power Fits 1300 Spicer drive which goes beneath radiator off front of crankshaft Electrical: 12 volt system throughout, with Delco 100 amp. alternator minimum Three Group 31 batteries 12 volt, 2190 CCA minimum each Threaded terminal posts Circuit breakers in place of fuses Exhaust: Single vertical muffler and stack located on back right of cab corner 11 foot height Stainless or chrome guard Cab and Accessories: Conventional cab with tilting fiberglass hood and fenders, without gullwing access, aluminum cab Interior including, but not limited to, the following: Floor mounted accelerator pedal Foam padded, cloth center, air adjustable high back drivers seat, lumbar support with arm rest Passenger seat, same as driver s seat Dual motorized & heated mirrors with 8 inch convex spot mirrors Arm rests on both doors Dual sun visors and stainless steel outside sunvisor Single electric horn Dual air horns on cab roof with front snow shields Heavy duty heater/defroster/air conditioner Dual windshield wipers, heavy duty electric with intermittent control Windshield washers with under hood reservoir. Turn signal lights with hazard switch I.C.C. clearance and marker lights L.E.D. Outside assist handles right and left Two steps right and left Minimum 6 switches in dash, 4 wired to back of frame, 2 wired to back of cab Factory installed AM/FM radio with clock and bluetooth All electric window control Inside/outside air intake system on engine
8 Tinted single glass windshield, tinted glass in other positions 2 extended rear window Interior dome light with manual switch Audible back up alarm at rear of frame Ignition and door keyed alike Floor mat (no carpet) Interior color, standard gray with Smart Sound insulation package Tilt steering wheel, 18 Vehicle speed sensor signal at fuse panel, accessible connection Air ride cab VHF wiring for two-way radio Safety: Equipped in compliance with all applicable Federal and Motor Vehicle Safety Standards and Regulations, including triangles, fire extinguisher (ABC style 5# to be mounted by Road Commission) Paint and Color: Cab, County Green, to be discussed prior to ordering Chassis, semi-gloss black Literature enclosed per specifications One factory type service, repair and electric diagram manual for chassis and engine paper or CD One software for the engine and antilock compatible with a lap top computer Company Name
9 Warranty Definition: Engine: Transmission: Rear axle: Optional Warranties and Cost Cab and Chassis Truck $ each Payment Terms Company Name Company Address Signature of authorized agent Written Telephone Number Email Address Date Federal Employer ID# Typed/Printed Fax# NOTE: Questions concerning specifications should be directed to Steve Roose, Director of Equipment at (616)242-6955 or (616) 481-5368. K:\Purchasing\SPEC\TRUCK74K-2019 5 axle.doc