Disc Valve Hydraulic Motors Series 0 10.20 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.20 EN EATON_Motoren english
Highlights Features 10 displacements, a variety of mounting flanges and output shafts Reliable, proven design High efficiency Environmental protection options Benefits Flexiblilty in designing this motor into a system Options that fit well into tough applications Applications Mowing Snow Removal Sprayer Trencher Wood Products Description The offers up to in-lb of torque and 25 gpm (continuous ratings). This is the corner stone of the Char-Lynn line. Mowing Motors Geroler Element Flow l/min [GPM] Speed RPM Pressure bar [PSI] Torque Nm [lb-in] 10 Displacements [25] Continuous** 0 [40] Intermittent* 722 Cont.** 6 Inter.* 200 [00] Cont.** 0 [00] Inter.* 9 [] Cont.** 0 [100] Inter.* ** Continuous (Cont.) Continuous rating, motor may be run continuously at these ratings * Intermittent (Inter.) Intermittent operation, 10% of every minute. Snow Removal Sprayer Trencher Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 2
Specifications 0 SERIES MOTORS Displ. cm 3 /r [in3/r] 0 [ 6.7] 1 [ 7.9] 160 [ 9.9] 205 [12.5] 2 [.0] 20 [.1] 310 [19.0] 3 [24.0] 4 [.0] 625 [.0] Speed Continuous 697 722 52 9 3 336 3 9 191 1 (RPM) Intermittent 6 62 693 546 2 4 422 3 5 241 @ Flow Flow Continuous 75 [20] [25] [25] [25] [25] [25] [25] [25] [25] [25] l/min [GPM] Intermittent [25] 1 [] 1 [] 1 [] 1 [] 1 [] 1 [] 0 [40] 0 [40] 0 [40]. Torque* Continuous 320 [250] 375 [33] 45 [42] [50] 5 [6240] 7 [6666] 50 [75] 9 [ 240] 9 [ 375] 9 [ 605] Nm [lb-in] Intermittent 4 [4160] 560 [4940] 5 [6240] 00 [7100] [74] 7 [471] 1065 [9420] 5 [104] [100] 0 [100] Pressure Continuous 205 [00] 205 [00] 205 [00] 205 [00] 205 [00] 205 [00] 205 [00] 1 [2750] 0 [2000] 1 [10] bar Intermittent 310 [00] 310 [00] 310 [00] 260 [3750] 310 [00] 260 [3750] 260 [3750] 240 [00] 1 [2500] 0 [2000] [ PSI] Peak 310 [00] 310 [00] 310 [00] 310 [00] 310 [00] 310 [00] 310 [00] 2 [4250] 0 [30] 10 [2] Weight Standard or.9 [39.5] 1.1 [40.0] 1.1 [40.0] 1.4 [40.5] 1.6 [41.0] 19.1 [42.0] 19.5 [43.0] 20.4 [.0] 21. [4.0].1 [51.0] kg [lb] Wheel Mount Bearingless.1 [31.0].3 [31.5].1 [31.0].5 [32.0].7 [32.5].2 [33.5].6 [34.5] 16.6 [36.5].9 [39.5] 19.3 [ [42.5] Maximum Case Pressure: See case pressure seal limitation graph. *See shaft torque ratings for limitations.. Note: To assure best motor life, run motor for approximately one hour at % of rated pressure before application to full load. Be sure motor is filled with fluid prior to any load applications. Maximum Inlet Pressure: 310 bar [00 PSI] Do not exceed pressure rating (see chart above). Maximum Return Pressure: 310 bar [00 PSI] with case drain line installed. Do not exceed pressure rating (see chart above). bar [ PSI] : The true pressure difference between inlet port and outlet port Continuous Rating: Motor may be run continuously at these ratings Intermittent Operation: 10% of every minute Peak Operation: 1% of every minute Recommended Fluids: Premium quality, anti-wear type hydraulic oil with a viscosity of not less than SUS at operating temperature. Recommended Maximum System Operating Temp.: 2 C [10 F] Recommended Filtration: per ISO Cleanliness Code, 4406: 20/1/13 Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 3
160 cm 3 /r [9.9 in 3 /r] Performance Data Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Flow LPM [GPM] [.5] 1,9 [1] 3, [2] 7,5 [4] [6] [] [10] [12] [] [16] [1] 6 [20] [22] 3 [25] [] 1 Continuous Intermittent [250] [] [410] [420] 36 [4] 50 73 [4] 50 107 [410] 4 [3] 12 [0] 40 2 [3] 256 [2] 291 [2] 329 [0] 25 366 [1] 20 402 [0] 9 [500] [10] 5 [00] 1 1 205 cm 3 /r [12.5 in 3 /r] [00] Peak No Operation [2000] 0 [2500] [00] [00] [0] 1 205 240 275 [] [] [2220] [260] [60] [60] [] 10 16 250 325 4 12 5 0 9 [50] [160] [2410] [30] [4060] [] [5420] [0] 1 34 2 32 5 29 460 27 540 25 0 22 60 16 [] [] [25] [3410] [4260] [5040] [57] [6340] 100 73 200 71 2 5 6 40 5 57 6 7 [0] [100] [2620] [] [43] [51] [50] [65] 100 106 205 2 103 101 4 9 55 665 1 7 74 [] [120] [2660] [60] [4410] [5240] [6020] 100 3 205 2 0 1 136 500 132 5 125 60 6 [60] [120] [20] [0] [4460] [50] [10] 10 205 9 5 4 405 1 505 166 160 6 2 [50] [0] [26] [] [4440] [50] 216 205 2 5 2 405 202 500 200 194 [40] [] [26] [60] [44] [52] 200 0 500 254 252 24 243 7 229 [20] [] [2650] [40] [4410] [520] 2 200 29 0 24 20 500 272 5 264 [10] [50] [2640] [20] [4] [52] 327 200 325 0 321 316 4 5 29 [00] [] [2620] [10] [40] [52] 364 1 362 2 3 3 4 3 5 334 [70] [16] [2] [00] [43] 1 39 2 394 3 9 4 0 [750] [1640] [2560] [340] [4360] 5 15 2 3 4 6 3 44 442 434 [710] [40] [2510] [] [41] 0 5 25 0 546 542 7 529 520 [5260] 5 36 [5240] 5 421 [50] 5 504 [20] 6 15 [20] 6 219 [20] 6 2 [20] 6 27 [20] 6 321 [5510] 625 3 [67] 5 109 [6] 70 3 [00] 310 [6210] 0 [6740] 0 [7100] 00 65 Flow LPM [GPM] [.5] 1,9 [1] 3, [2] 7,5 [4] [6] [] [10] [12] [] [16] [1] 6 [20] [22] 3 [25] [] 1 [250] [500] [00] [2000] 0 [2500] [00] [00] [0] [00] 1 205 240 275 310 [0] [60] [1320] [2050] [2750] 75 0 0 310 7 5 3 1 [4410] [40] [0] [10] [20] [270] [30] [3940] 0 5 2 3 375 4 22 20 19 1 16 500 560 2 [0] [1360] [200] [27] [3340] [39] [] [50] 0 5 2 3 375 0 510 575 41 40 37 32 29 27 25 [320] [3] 46 [320] 93 [0] 137 [20] 14 [260] 2 [240] 25 277 [220] 25 321 [200] 25 366 [10] 20 410 [0] 460 [] 509 [] 10 52 [710] [00] [2100] [220] [3420] [4020] [4620] [5220] 0 92 160 240 320 4 5 5 73 520 62 5 51 [710] [20] [20] [250] [10] [410] [40] [40] 0 1 160 134 240 131 320 126 3 4 1 540 605 75 [720] [10] [210] [20] [60] [40] [450] [54] 0 12 165 10 2 1 3 1 163 40 4 550 1 620 122 [720] [0] [2220] [20] [30] [42] [4920] [5560] 0 229 165 226 250 221 3 216 410 206 45 194 555 12 6 169 [0] [10] [21] [2920] [] [420] [4920] [55] 0 274 165 272 2 266 3 260 405 250 45 555 224 6 209 [60] [20] [2160] [2] [] [42] [4920] [550] 75 160 2 325 405 40 555 6 319 31 3 4 294 22 266 249 [6] [00] [21] [260] [50] [4260] [4920] [55] 75 364 160 362 240 6 325 34 3 40 326 555 6 29 [650] [1360] [2100] [2] [] [4250] [4910] [5] 75 5 2 320 40 555 6 409 407 401 392 2 3 0 329 [6] [1340] [20] [200] [10] [4240] [4910] 0 6 2 44 3 440 3 429 40 4 555 396 [620] [13] [2060] [27] [00] [4220] [4910] 506 0 502 2 494 3 44 3 473 4 555 4 [] [1320] [2050] [270] [340] [4210] [40] 0 0 3 3 555 57 573 563 552 540 526 501 [560] [120] [19] [20] [34] [39] [4640] 65 1 5 3 0 525 693 67 675 6 647 6 [19] Torque [lb-in] } Nm 675 Speed RPM [50] 6 373 [5] 6 413 [55] 6 474 [55] 6 13 [57] 6 [5] 665 57 [6010] 60 100 [60] 6 2 [0] 0 12 [6200] 0 222 [6220] 5 262 [6240] 5 2 Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 4
5 Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 >> [510] 60 [10] 1 [60] 5 60 [200] 2 60 [2] 2 59 [31] 5 59 [510] 60 91 [1040] [] 5 [2100] 2 9 [2620] 2 [3160] 5 [500] 55 121 [1020] 1 121 [60] 5 [20] 240 9 [26] 2 [] 5 1 1 1 [40] 5 0 [2100] 2 [2620] 2 [] 5 7 [250] [500] [750] 50 [1250] 5 [00] [4] [6] [] [10] Pressure Bar [PSI] 2 cm 3 /r [.0 in 3 /r] [36] 410 5 [3660] 4 6 [360] 4 1 [36] 4 1 [50] [460] 50 5 [90] 0 2 [40] 55 [9] 0 [] 1 [19] 13 [240] 20 13 [29] 3 12 [500] 55 1 [20] 1 29 [2040] 0 29 [2540] 25 2 [50] 3 27 [.5] 1,9 [1] 3, [2] 7,5 [3] 5 12 [3420] 5 26 [41] 465 56 [4200] 3 [4210] 3 [40] 40 3 [2000] 0 [] 4 [39] 4 24 Flow LPM [GPM] Torque [lb-in] Nm } Speed RPM [46] 525 [4710] 5 0 [0] 5 [4440] 500 [5] 50 49 [90] 0 12 [] 5 10 [200] 2 9 [20] 2 [30] 5 [12] [360] 4 1 [2500] 1 [960] 0 212 [20] 1 2 [2060] 2 210 [2] 2 209 [31] 5 20 [] [36] 4 206 [0] 243 [00] 1 242 [2040] 0 241 [250] 2 240 [3] 5 9 [16] [3660] 4 6 [9] 274 [0] 165 273 [2020] 0 272 [2560] 2 2 [30] 0 269 [1] 6 [3650] 4 266 [910] 5 [60] 165 4 [2000] 3 [2550] 2 2 [3100] 0 0 [20] [] 100 336 [20] 160 3 [19] 334 [2500] 20 332 [50] 3 3 [22] 3 [20] 2 [10] 5 1 [19] 220 0 [2460] 20 37 [290] 3 3 [25] [1250] 0 6 [160] 210 5 [] 1 [4] 55 2 [0] 50 13 [420] 213 [] 244 [0] 275 [0] 40 5 [310] 337 [4250] 40 [40] 555 22 [5220] 5 75 [260] 3 [60] 75 7 [] 2 3 [20] 3 0 [3640] 410 296 [4740] 5 1 [47] 540 1 [4220] 3 [4200] 203 [41] 2 [410] 4 262 [] 405 326 [40] 372 [34] 3 4 [41] 4 292 [10] 125 2 [40] 1 1 [] 132 [22] 255 52 [27] 3 525 [3340] 375 519 [3340] 375 519 [40] 460 369 [4640] 525 365 [3960] 4 442 [4460] 505 437 [510] 55 7 [40] 560 427 [3910] 440 5 [4] 4 509 [40] 465 3 [460] 5 319 [5200] 5 313 [560] 640 6 [4710] 5 259 [50] 5 254 [5720] 6 24 [40] 5 2 [5220] 5 23 [5710] 6 2 [6200] 0 241 [2750] 1 [00] 205 [3250] [00] 240 [3750] 260 [460] 5 10 [5020] 565 4 [5250] 5 106 [52] 137 [55] 6 47 [56] 6 72 [5720] 6 103 [60] 60 44 [60] 6 [6200] 0 99 [20] 20 [5740] 650 1 [640] 7 42 [6620] 750 67 [66] 755 96 [60] 6 16 [6] 775 39 [50] 7 63 [6640] 750 [7340] 36 [] 10 [74] 40 59 [] 00 91 [74] 7 [50] 650 133 [6240] 5 129 [6710] 0 125 [70] 05 [40] 540 1 [520] 5 166 [5750] 650 1 [60] 5 7 [60] 755 2 [4740] 5 200 [5260] 5 1 [5740] 650 1 [6220] 5 15 [47] 5 229 [5250] 5 [57] 650 219 [6210] 0 213 [579] 65 [67] 132 [74] 26 52 [2962] 3 51 [57] 402 51 [4139] 46 50 [53] 66 79 [17] 133 79 [] 271 7 [297] 3 77 [3601] 407 77 [4193] 474 [573] 65 106 [167] 132 106 [2404] 272 [07] 340 104 [30] 40 104 [421] 477 102 [16] 1 133 [] 271 131 [2997] 339 131 [3629] 410 1 [4] 479 129 [250] [500] [750] 50 [1250] 5 [00] [4] [6] [] [10] Pressure Bar [PSI] 20 cm 3 /r [.1 in 3 /r] [4712] 2 49 [4793] 542 74 [412] 544 101 [437] 547 127 [50] [3] 60 4 [1074] 121 2 [5] 62 12 [36] 12 12 [227] 25 [241] 321 [3394] 4 [6] 437 10 [56] 64 26 [16] 1 26 [2] 263 25 [22] 32 24 [34] 391 24 [] 447 [.5] 1,9 [1] 3, [2] 7,5 [49] 496 10 [24] 5 22 [525] 597 47 [] 607 72 [54] 1 99 [5442] 6 126 [2000] 0 [4] 5 10 [2922] 3 21 Flow LPM [GPM] [0] 5 [63] 722 44 [26] 127 160 [69] 26 [2991] 3 7 [3609] 40 7 [422] 47 6 [12] [432] 546 4 [2500] 1 [06] 125 17 [44] 265 16 [2972] 336 15 [5] 405 14 [4213] 4 12 [] [416] 544 10 [1096] 124 2 [24] 263 212 [2947] 333 2 [65] 403 210 [4203] 20 [16] [1075] 121 241 [2299] 260 9 [29] 3 7 [41] 6 [41] 473 4 [1] 6 [5] 19 26 [2274] 257 267 [29] 327 266 [21] 39 264 [4] 472 2 [20] [1005] 1 2 [7] 255 294 [256] 3 292 [340] 393 2 [4136] 467 2 [25] [940] 106 336 [21] 252 334 [225] 319 333 [3419] 6 331 [406] 462 32 [] 1 [21] 243 [2759] 312 39 [] 132 [26] 296 464 [547] 62 134 [527] 60 1 [497] 56 17 [472] 2 [437] 39 241 [402] 26 [366] 41 296 [66] 694 19 [6666] 7 [7191] 13 [7749] [3] 940 13 [5] 663 6 [313] 360 463 [332] 3 396 [3] 439 7 [394] 0 392 [4] 544 206 [401] 542 1 [4791] 541 25 [6] 7 25 [5441] 6 2 [22] 3 [1] 34 336 [] 96 402 [2057] 2 466 [71] 200 52 [1] 201 7 [0] 201 [15] 199 133 [] 194 12 [40] 197 25 [] 197 16 [] 1 16 [] 194 213 [16] 191 240 [1669] 19 26 [1629] 14 2 [] 9 3 [0] 167 401 [134] 2 46 [4710] 2 325 [54] 6 [6521] 737 67 [6946] 75 42 [36] 720 6 [2750] 1 [00] 205 [3250] [00] 240 [3750] 260 [6] 7 6 [79] 1 5 [54] 65 4 [7502] 4 41 [020] 6 40 [471] 7 [2] 00 66 [07] 59 65 [097] 9 64 [6556] 741 94 [22] 793 92 [6601] 746 9 [22] 793 1 [751] 49 [751] 49 1 [6940] 74 1 [6940] 74 166 [656] 744 4 [54] 6 [56] 636 20 [600] 65 [59] 673 69 [5994] 677 96 [60] 62 122 [6034] 62 [65] 736 1 [6436] 727 1 [6362] 719 219 [602] 61 4 [5919] 669 199 [5919] 669 224 [551] 6 249 [5420] 2 203 [5] 0 229 [94] 609 255 [5205] 5 279 [5205] 5 3 [44] 492 449 [73] 5 9 [5021] 567 377 Performance Data Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Continuous Intermittent Peak No Operation
Performance Data Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Flow LPM [GPM] [.5] 1,9 [1] 3, [2] 7,5 [4] [6] [] [10] [12] [] [16] [1] 6 [20] [22] 3 [25] [] 1 [] 132 [40] 1 Continuous Intermittent [250] [500] [750] 50 3 cm 3 /r [24.0 in 3 /r] Peak No Operation [1250] 5 [00] [50] [2000] [0] [2500] 0 5 1 [0] [1340] 0 4 0 2 [750] [] [20] [27] [3460] [41] [4] [50] [6310] [10] [70] 5 9 160 9 240 3 3 4 7 550 7 6 7 7 5 7 4 2 [00] [00] [22] [] [50] [4620] [10] [0] [6750] [74] [240] [9] 1 1 1 260 340 16 4 16 520 60 5 13 13 9 12 10 [60] [16] [24] [3310] [4] [40] [5640] [63] [71] [7] [70] 15 20 37 375 36 465 36 555 6 720 34 10 34 33 9 32 [60] [16] [2540] [3410] [410] [490] [570] [650] [7] [220] 57 1 57 25 56 5 55 4 54 565 655 52 7 50 49 9 47 [40] [160] [2550] [3] [4260] [50] [5] [6650] 1 2 75 5 74 40 73 575 72 665 750 6 [00] [160] [2550] [3] [4260] [5100] [5920] [67] 1 2 94 5 93 40 92 575 91 6 9 0 6 [0] [1660] [2520] [30] [42] [50] [50] 5 1 1 1 25 3 0 2 40 1 575 0 665 10 [740] [1640] [24] [33] [4260] [5100] [50] 5 15 20 0 40 575 665 133 133 132 131 1 129 127 [710] [1620] [2460] [] [4240] [500] [540] 0 15 20 0 40 575 660 3 3 2 1 9 7 1 [60] [1] [24] [3340] [4220] [5060] [510] 75 10 275 375 5 655 2 2 1 1 16 166 164 [0] [0] [2] [3320] [4210] [5040] [570] 10 2 375 5 655 192 191 1 19 17 15 13 [5] [] [40] [3220] [4160] [5010] 65 2 1 210 265 209 365 20 4 206 565 204 [4] [10] [0] [0] [40] [4960] 55 5 255 0 460 560 9 7 6 2 3 [100] [1650] [22] [20] [50] 15 255 340 4 25 24 22 21 279 [20] [2] [2] [30] 1 240 325 425 331 3 32 325 [2050] [27] [3620] 0 3 410 3 374 371 [5740] 650 201 [50] 6 0 [66] 755 [6650] 750 124 [740] 66 [7560] 55 4 Flow LPM [GPM] [.5] 1,9 [1] 3, [2] 7,5 [4] [6] [] [10] [12] [] [16] [1] 6 [20] [22] 3 [25] [] 1 [] 132 [2750] 1 [640] [12] [1960] [2640] [32] [3940] [4] [5240] [50] [6510] [] [77] [0] [9100] 47 1 47 220 46 0 46 3 4 520 44 5 44 665 43 7 42 10 42 0 41 5 41 10 40 [650] [10] [19] [2660] [3320] [0] [460] [] [] [66] [720] [7940] 75 71 1 71 0 375 69 0 69 5 6 67 675 66 750 64 25 64 63 [640] [10] [190] [26] [] [40] [4710] [60] [6020] [66] 96 1 96 0 0 94 5 94 5 93 605 92 60 91 755 9 [620] [120] [19] [2660] [3340] [40] [4740] [] [6050] [6710] 121 1 0 9 375 9 460 5 1 0 6 65 1 0 2 [00] [3250] 205 [00] 240 [97] [104] 00 5 10 310 cm 3 /r [19.0 in 3 /r] [250] [500] [750] 50 [1250] 5 [00] [50] [2000] [0] [2500] [2750] 0 5 1 1 [00] 205 [3250] [00] 240 [3750] 260 [] [10] 1 4 2 [620] [12] [1920] [2560] [31] [370] [42] [40] [54] [600] [66] [72] [70] [4] [0] 1 2 2 360 425 45 555 620 65 755 20 960 1025 10 10 10 9 9 9 7 7 6 5 [6] [120] [1940] [25] [] [] [40] [50] [560] [60] [6910] [75] [160] [7] [9420] 1 220 22 2 22 365 21 4 21 505 20 575 20 640 19 710 1 70 1 50 920 9 16 1065 [] [1260] [1940] [26] [3340] [4040] [47] [] [6060] 1 0 4 220 4 2 3 375 2 5 2 5 1 0 0 65 139 [5] [1240] [1920] [2] [3310] [0] [4710] [0] [6060] 65 0 2 2 375 0 5 0 65 169 169 16 16 167 167 165 164 163 [540] [10] [10] [250] [320] [39] [40] [0] [6050] 60 0 2 2 3 0 5 0 65 193 193 192 192 1 19 1 17 15 [4] [1210] [10] [2550] [3240] [39] [460] [] [6040] 55 1 210 2 365 4 5 605 60 2 2 216 216 2 213 2 209 207 [0] [] [160] [2520] [3210] [30] [46] [60] [60] 50 1 210 25 365 440 5 605 60 242 242 242 241 240 6 4 2 [420] [] [120] [2520] [310] [] [4640] 267 1 266 205 266 25 265 360 264 440 262 525 260 [340] [0] [0] [2510] [3160] [20] [] 40 200 25 5 4 520 3 3 2 1 0 299 296 [1010] [10] [2420] [3100] [3720] [00] 1 1 275 0 420 510 363 362 360 9 4 [0] [60] [20] [40] [43] 10 265 3 4 422 420 419 41 413 [43] Torque [lb-in] 4} Nm 413 Speed RPM [20] 25 [520] 5 293 [50] 50 1 [6720] 0 1 [67] 0 9 [7320] 25 [73] 109 Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 6
4 cm 3 /r [.0 in 3 /r] Performance Data Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Flow LPM [GPM] [.5] 1,9 [1] 3, [2] 7,5 [4] [6] [] [10] [12] [250] [500] [750] 50 625 cm 3 /r [.0 in 3 /r] [1250] 5 [00] [1] 100 1 2 [100] [40] [3] [450] [00] [] [720] [2] [0] 5 265 5 405 5 550 4 6 4 3 5 3 9 2 9 2 [105] [0] [3675] [5010] [60] [25] [1] [605] [] 125 2 4 565 13 7 12 60 9 10 9 9 10 [10] [2420] [3750] [55] [6] [70] [410] [00] [] 125 275 425 55 22 7 21 19 0 1 10 105 16 [10] [2460] [25] [5220] [6620] [] [4] [910] [94] 125 20 4 5 34 750 33 0 31 0 1005 29 10 2 [00] [2500] [30] [52] [6640] [79] [460] 125 4 20 4 440 47 5 46 750 5 43 5 43 [] [2550] [3975] [20] [66] [0] [5] 1 60 2 60 0 59 5 755 57 910 54 9 [60] [2] [4050] [75] [60] [100] 1 2 72 460 71 605 755 69 9 65 72 [] [1] [25] [3965] [25] [665] [065] 125 25 0 755 910 4 4 3 2 1 77 [16] [0] [2465] [0] [5275] [66] [0] 20 440 5 755 910 96 94 93 9 [1] [9] [2405] [25] [5240] [6655] [73] 0 2 4 5 750 6 10 107 107 104 100 [20] [25] [] 1 [] 132 [40] 1 Continuous Intermittent Peak No Operation [9] [20] [37] [5205] [6640] 121 265 425 5 750 6 [750] [25] [3] [5000] [6] 5 2 405 565 725 1 0 9 7 6 [550] [1975] [3] [] [6200] 60 5 5 0 10 9 7 1 [3125] [] 5 5 210 20 [250] [42] 320 45 241 9 [660] 90 64 [620] 975 [50] 9 [10] 1 [925] 1010 42 [] 10 52 [100] 125 [2000] 0 [10075] 10 7 [100] 0 Flow LPM [GPM] [.5] 1,9 [1] 3, [2] 7,5 [4] [6] [] [10] [12] [] [16] [1] 6 [20] [25] [] 1 [] 132 [40] 1 [250] [500] [750] 50 [1250] 5 [00] [50] [2000] [0] 0 5 [00] [50] 200 3 1 [0] [175] [275] [25] [4775] [5720] [66] [00] 100 210 325 4 540 6 755 60 7 6 6 5 4 3 2 1 [90] [5] [1940] [2975] [39] [5010] [6010] [10] [000] 100 220 3 0 565 60 7 5 1 16 12 10 10 [9] [2005] [75] [4160] [52] [60] [75] [375] [9] [100] 29 3 2 4 27 5 26 710 21 9 19 1060 [920] [2010] [3100] [415] [5265] [63] [7420] [4] [9465] 44 0 43 42 5 40 7 37 40 5 32 10 [5] [20] [3125] [4205] [52] [65] [745] 100 0 60 5 59 57 55 720 52 49 [0] [19] [] [4205] [52] [63] [740] 100 75 72 720 66 63 0 74 [60] [1975] [] [4200] [55] [63] [7] 91 0 9 7 5 720 1 77 [] [19] [55] [4165] [5275] [6360] [74] 220 3 4 5 720 40 106 104 102 100 96 92 [05] [1910] [20] [41] [52] [63] [7420] 2 340 465 5 7 40 122 9 1 1 1 107 [740] [160] [290] [4] [52] [65] [70] 5 210 3 465 5 7 137 136 134 132 1 125 121 [60] [0] [2940] [405] [5] [625] 75 205 3 460 5 710 3 2 0 7 1 0 [5] [1665] [200] [5] [5210] [] 65 1 3 5 5 6 191 19 17 14 12 7 [20] [26] [35] [45] [595] 1 0 425 550 675 22 226 2 220 2 [2] [10] 2 3 265 263 [25] [3260] 2 3 5 3 [250] Torque [lb-in] 320} Nm 241 Speed RPM [510] 960 46 [525] 960 59 [2500] 1 Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 7
Dimensions Standard Mount Standard Mount Ports 1 1/16-12 UN-2B SAE O-ring Staggered Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or 4 Bolt 3/4 inch Split Flange Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or G 3/4 (BSP) Staggered Ports (2) G 1/4 (BSP) Case Drain Port (1) Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW Port B Port B YY XX Y X 22,4/21, [./.6] 127,0 [5.00] Dia. Bolt Circle 101,60/101,47 [4.000/3.9] Dia. 9,9 [4.72] Max, Square 4 Bolt 3/4 Inch Case Drain Port Split Flange Ports SAE C Flange Add 4,3 [.] to X and Y Dim. (see Chart) Flange Comparison SAE B/ SAE C 26,7/26.2 [1.05/1.03] 4,3/3,3 [./.13] 10,7/9,1 [.42/.36] 12,7/12,4 [.50/.49] 127,00/126,7 [5.000/4.9] Pilot Dia.,3 [5.4] Square 9,0 [3.6] Square,2/,5 [.60/.57] (4),/, [.572/.557] Dia. Thru 1,92 [6.375] Dia. B.C.,2/63,5 [3.00/2.50] STANDARD MOUNT MOTOR DIMENSIONS Displacement X Y XX YY cm 3 /r [in 3 /r] mm [inch] mm [inch] mm [inch] mm [inch] 0 [ 6.7],3 [6.] 2,4 [.44] 167,3 [6.59] 246,3 [ 9.] 1 [ 7.9] 162,3 [6.39] 21,4 [.60] 1,3 [6.75] 250,4 [ 9.6] 160 [ 9.9] 16,7 [6.64] 224,7 [.5] 7,7 [7.00] 256,7 [10.] 205 [12.5] 7,2 [6.9] 3,2 [ 9.1] 16,2 [7.33] 265,2 [10.44] 2 [.0] 16,7 [6.64] 224,7 [.5] 7,7 [7.00] 256,7 [10.] 310 [19.0] 7,2 [6.9] 3,2 [ 9.1] 16,2 [7.33] 265,2 [10.44] 3 [24.0] 17,9 [7.40] 243,9 [ 9.60] 196,9 [7.75] 275,9 [10.6] 4 [.0] 200,7 [7.] 256, [10.] 209,7 [.26] 2, [.37] 625 [.0] 2, [.5] 273,9 [10.7] 226,7 [.93] 5,9 [12.04] Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9
Dimensions Wheel Mount Wheel Mount Ports 1 1/16-12 UN-2B SAE O-ring Staggered Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or 4 Bolt 3/4 inch Split Flange Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or G 3/4 (BSP) Staggered Ports (2) G 1/4 (BSP) Case Drain Port (1) Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW YY Port B XX Port B Y X 21,/21,3 [.6/.4] 4 Bolt 3/4 inch Split Flange Ports Case Drain Port 1, [3.22] 9,7/,6 [./.34] 139,/139,57 [5.500/5.4] Dia. 10,7 [4.2] Dia. Case Drain Port 6,74 [4.596] Square,/, [.572/.557] Thru (4), [5.6] Square 124,2 [4.9] 165,0 [6.50] Dia. Bolt Circle WHEEL MOUNT MOTOR DIMENSIONS Displacement X Y XX YY cm 3 /r [in 3 /r] mm [inch] mm [inch] mm [inch] mm [inch] 0 [ 6.7] 7,5 [3.] 3,3 [5.64] 96,4 [3.0] 5,3 [6.] 1 [ 7.9] 91,6 [3.] 7,3 [5.0] 100,5 [3.96] 9,3 [7.06] 160 [ 9.9] 97, [3.5] 3,7 [6.05] 106, [4.21] 15,7 [7.31] 205 [12.5] 106,4 [4.19] 162,3 [6.39] 1,4 [4.55] 194,3 [7.65] 2 [.0] 97, [3.5] 3,7 [6.05] 106, [4.21] 15,7 [7.31] 310 [19.0] 106,4 [4.19] 162,3 [6.39] 1,4 [4.55] 194,3 [7.65] 3 [24.0] 1,1 [4.] 3,0 [6.1] 126,1 [4.97] 205,0 [.07] 4 [.0] 129,9 [5.12] 15,7 [7.31] 1, [5.47] 2,7 [.57] 625 [.0] 6,9 [5.79] 202,9 [7.99] 6,0 [6.] 2,0 [9.25] Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 9
Dimensions Bearlingless Bearingless Ports 1 1/16-12 UN-2B SAE O-ring Staggered Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or 4 Bolt 3/4 inch Split Flange Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or G 3/4 (BSP) Staggered Ports (2) G 1/4 (BSP) Case Drain Port (1) Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW YY Port B XX Port B Y X 1,9 [6.375] Bolt Circle.50/, [.572/.557] 127,0/126,9 [5.000/4.9] Dia. 1,5 [4.50] Square 4 Bolt 3/4 inch Split Flange Ports For Bearingless Motor application information contact your Eaton representative (mating coupling blanks available from Eaton Hydraulics). Note: After machining blank, part must be hardened per Eaton specification. Case Drain Port C 47,2 [1.6] Dia. D 2,5 [4.43] E 107,4 [4.] Full Form Dia. F 7,4 [.29]Min. Full Form Dia. G 6, [2.71] H 56,9 [2.24] Dia. J 1,29 [.720] K º Mating Coupling Blank Eaton Part No. 127-003 J C H K F D E G 25,9 [1.02] 24,1/21,1 [./.3] Case Flow Hole 7,6 [5.1] Square Face Seal or O-ring Seal 12,4 [.49] BEARINGLESS MOTOR DIMENSIONS Displacement X Y XX YY cm 3 /r [in 3 /r] mm [inch] mm [inch] mm [inch] mm [inch] 0 [ 6.7] 91,0 [3.5] 6, [5.7] 100,1 [3.94], [7.04] 1 [ 7.9],0 [3.74] 0, [5.94] 104,1 [4.10] 12,9 [7.20] 160 [ 9.9] 101,4 [4.00] 7,1 [6.19] 0,5 [4.] 19,2 [7.] 205 [12.5] 109,9 [4.33] 165,7 [6.52],9 [4.6] 197,6 [7.7] 2 [.0] 101,4 [4.00] 7,1 [6.19] 0,5 [4.] 19,2 [7.] 310 [19.0] 109,9 [4.33] 165,7 [6.52],9 [4.6] 197,6 [7.7] 3 [24.0],6 [4.75] 1,3 [6.94] 129,5 [5.10] 20,3 [.20] 4 [.0] 133,5 [5.26] 19,2 [7.] 2,5 [5.] 221,2 [.71] 625 [.0] 0,5 [5.93] 206,3 [.12] 9,5 [6.2],3 [9.] Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 10
Installation Information Bearingless 1 Internal spline in mating part to be as follows: Material to be ASTM A4, 620H. Carbonize to a hardness of 60-64 HRc with case depth (to 50HRc) of 0,0-1,27 [.0 -.050] (dimensions apply after heat treat). 2 Mating part to have critical dimensions as shown. Oil holes must be provided and open for proper oil circulation. 3 Seal to be furnished with motor for proper oil circulation thru splines. 4 Some means of maintaining clearance between shaft and mounting flange must be provided. 5 Counterbore designed to adapt to a standard sleeve bearing 50,010-50,040 [1.969-1.] ID by 60,050-60,00 [2.3642-2.36] (Oilite bronze sleeve bearing). 6 Similar to SAE C Four Bolt Flange. 7 52, [2.0] dimension to be maintained when assembling shipping and installing unit to insure valve drive engagement with valve (this is required on displacement code number 24 only).,0/13,2 [.55/.52],9/,4 [./.33],6/52,6 [2./2.07] Coupling Depth 7 16 º º 1,5/0, [.06/.03] 5,1/4,6 [.20/.1] Dia. (2) Thru Oil Hole 2 31º 29º Case Flow 49,4/49,22 [1.9625/1.96] Dia. -D- 0,13 [.005] B 52,37 [2.062] R Dia. Min. 1,/1,2 [.07/.05] 5 Major 65,0/64,5 [2.56/2.54] Circular Tip R. Minor Finish Finish Fillet R. Pitch Form 5,6/5,1 [.22/.20],1/22,6 [.91/.9] 4 6 3 Case Flow ( -B- ) Spline Pitch...10/20 Pressure Angle... Number of teeth... 12 Class of Fit... Ref. 5 Type of Fit... Side Pitch Diameter... Ref.,00 [1.2000000] 0,20 [.00] D Base Diameter... Ref. 26,3965 [1.035] Major Diameter...33,43 [1.316] 33, [1.] Min. Min. Minor Diameter... 2,40-2,5 [1. - 1.125] Form Diameter, Min....32,59 [1.23] Fillet Radius... 0,63-0, [.025 -.0] Tip Radius... 0,26-0,51 [.010 -.020] Finish...1,6 (63) Involute Profile Variation...+0,000-0,025 [+.0000 -.0010] Total Index Variation...0,0 [.00] Lead Variation...0,013 [.0005] Circular Space Width: Maximum Actual...5,0 [.196] Minimum Effective...4,9 [.] Maximum Effective... Ref. 5,009 [.1972] Minimum Actual... Ref. 4,96 [.1963] Dimension Between Two Pins...Ref. 22,73-22,929 [.9 -.27] Pin Diameter...5,334 [.2100] Pins to Have 3,73 [.7] Wide Flat for Root Clearance Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9
Dimensions Shafts 1 1/4 Inch Straight [600] Torque Nm [lb-in] 7,963/7,937 [.31/.3125] Square Key,9/6,6 [2.79/2.] End of Shaft to Mounting Surface (Std) 42,0/40,6 [1.65/1.60],33/,07 [1.391/1.1] 3/-16 UNC 1,7[.74] Deep 31,75/31,69 [1.250/1.24] Dia.,1 [2.09] Coupling 1 1/4 - Tooth Splined [600] Torque Nm [lb-in] 3/-16 UNC 1,7 [.74] Deep Spline to Fit ANSI B92.1 19 Flat Root Side Fit Tooth 12/24 Spline 40 mm Straight 972 [] Torque Nm [lb-in] 43,03/42,72 [1.694/1.62],000/7,0 [.39/.31] M12 x 1,75-6H 24,9 [.9] Deep,10 [1.500] Dia. 12,000/.7 [.4724/.4],1 [1.50] Min. Full Spline 31,7 [1.250] Dia. 40,02/39,99 [1.5/1.575] Dia. 1 1/2 Inch -Tooth Splined 972 [] Torque Nm [lb-in] Spline to Fit ANSI B92.1 19 Flat Root Side Fit Tooth 12/24 Spline 31,2 [1.] Min. Full Spline 3/-16 UNC 1,7 [.74] Deep,9/6,6 [2.79/2.] End of Shaft to Mounting Surface (Std),1 [2.09] Coupling 93,9/92,0 [3.696/3.622] End of Shaft to Mounting Surface (Std) 9,2/4,5 [.36/.1],7/69,3 [2.7/2.73] 1,3 [3.20] Coupling 66,/65,0 [2.63/2.56] End of Shaft to Mounting Surface (Std) 33,2/33,02 [1.310/1.0] Dia. 51, [2.04] Coupling 1 5/ Tapered 1-1/4-1 UNEF-2A 972 [] Torque Nm [lb-in] 41,326/41,275 [1.62/1.6250] Dia. Recommended Torque: (6 Nm [ lb-ft] Dry) (510 Nm [375 lb-ft] Lub) Plus Torque required to align the slotted nut with the Shaft Crosshole. 1-1/4-1 UNEF 4,1 [.16] Dia. Thru SAE J501 Standard Tapered Shaft 125,00 0, Taper per Meter [1.500.002 Taper per Foot] Tapered Shaft Hub Data 59,1/56, [2.325/2.2] Slotted Hexagon Nut Hub 55,4 [2.1] 164,/162,1 [6.49/6.] End of Shaft to Mounting Surface (Whl),6 [3.00] 5,54/5,20 [.21/.205] 4,6 [.1] 31,7 [1.25],1/,2 [.45/.4375] Sq. Key,2 [.44],7 [.62] Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 12
Shaft Side Load Capacity These curves indicate the radial load capacity on the motor shaft(s) at various locations with an allowable external thrust load of 4 kg [1000 lb]. Note: Case pressure will increase the allowable Inward thrust load and decrease the allowable outward thrust load. Case pressure will push outward on the shaft at 94 kg/7 Bar [20 lb/100 PSI]. Thrust Load Standard Motor Straight and Splined Shafts [lb] [000] [00] [0] [5000] [0] [00] [2000] kg 00 00 2500 2000 00 1000 500 mm -100-0 -60-40 -20 0 20 40 60 0 100 [inch] [-4] [-3] [-2] [-1] 0 [1] [2] [3] [4] [5] Axial Loads 4 kg [1000 lb] Each curve is based on B 10 bearing life (2000 hours of 12,000,000 shaft revolutions at 100 RPM) at rated output torque. To determine radial load at speeds other than 100 RPM, multiply the load values given on the bearing curve by the factors in the chart below. RPM Multiplication Factor 50 1. 100 1.00 200 0.1 0 0.72 0.66 500 0.62 0.5 0 0.56 00 0.54 For 3,000,000 shaft revolutions or 500 hours Increase these shaft loads 52%. Wheel Motor Tapered Shaft [lb] [00] [000] [00] [0] [5000] [0] [00] [2000] 0 kg 0 00 00 2500 2000 00 1000 500 0 mm Mounting Surface -20 0 20 40 60 0 100 0 160 10 [inch] [-1] 0 [1] [2] [3] [4] [5] [6] [7] Mounting Surface Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 13
Case Pressure and Case Port Char-Lynn motors are durable and have long life as long as the recommended case pressure is not exceeded. Allowable case pressure is highest at low shaft speeds. Consequently, motor life will be shortened if case pressure exceeds these ratings (acceptability may vary with application). Determine if an external case drain is required from the case pressure seal limitation chart. Case Porting Advantage Contamination Control flushing the motor case. Cooler Motor exiting oil draws motor heat away. Extend Motor Seal Life maintain low case pressure with a preset restriction in the case drain line. 100 Case Pressure Bar 50 [PSI] 0 0 [2000] [00] [ 500] 0 Intermittent -- Case Drain Optional Case Pressure Seal Limitation Case Drain Required Continuous -- Case Drain Optional 0 100 200 0 500 0 00 0 Speed RPM Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9
Dimensions Ports 1-1/16-12 O-ring Ports (2) or G 3/4 (BSP) Ports (2) 4 Bolt 3/4 Inch Split Flange Ports to Fit SAE J51 c (2) Port B 7/16-20 UNF O-ring or G 1/4 (BSP) Case Drain Port 2,16/1,40 [.05/.055] Port B 7/16-20 UNF O-ring Case Drain Port 10,59/9,3 [.4/.7] 29,5/29,0 [1.16/1.] 13,2 [.52],7 [.62] º Port A 52,3/51, [2.06/2.04] Port A 47,63 [1.75],9 [.94] º 19,02/1,77 [.749/.739] º,2 [.44] 54,9 [2.16] 22, [.75] 52,3/51, [2.06/2.04] 69,6 [2.74] 5,9 [2.32] 5,9 [2.32],5 [3.01] 7/- O-ring Ports (2) or M22 x 1,5-6H Ports (2) Port B 29,5/29,0 [1.16/1.] 13,2 [.52] 69,6 [2.74] 5,9 [2.32] º 5,9 [2.32],7 [.62],5 [3.01] 42,7/,1 [1.6/1.50] 9/16-1 UNF O-ring or M12 x 1,5-6H O-ring Case Drain Port 6,73/5,99 [.265/.2] Port A 42,7/,1 [1.6/1.50] 6,9 [.27] Material Removed from this Housing for 7/- O-ring Ports and M22 x 1,5-6H Ports 73,4 [2.9] 5,7 [2.31] 5,7 [2.31],5 [3.01] 42,7/,1 [1.6/1.50] Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9
Product Numbers Note: For Motors with a configuration Not Shown in the charts below: Use model code number system on the next page to specify product in detail. Use digit prefix 109-, 0-, or 1- plus four digit number from charts for complete product number Example 1-7. Orders will not be accepted without three digit prefix. MOUNTING SHAFT PORT SIZE DISPL. cm 3 / r [in 3 / r] / PRODUCT NUMBER 1 1/4 Inch Straight 0 1 160 205 2 20* 310 3 4 625 [ 6.7] [ 7.9] [ 9.9] [12.5] [.0] [.1] [19.0] [24.0] [.0] [.0] 1 1/16 O-ring 109-00 -01-02 -03-04 -1094-1 -06-1212 -12 3/4 inch Split Flange 109-1001 -4-1002 -1003-5 -6-7 Standard SAE B-Mount 1 5/ Inch Tapered 1 1/4 Inch T Splined 1 1/16 O-ring 109-07 -0-09 -10 - -12-13 -79-3/4 inch Split Flange 109-1006 - -1007-100 -9-02 -10 1 1/16 O-ring 109- - -16 - -1-19 -1 3/4 inch Split Flange 109-10 -1062-1012 -1013-1063 -1064-1065 Standard SAE C-Mount 40 mm Straight G 3/4 (BSP) 109-4 -5-1227 -1224-1 -9-1 1/4 Inch T Splined G 3/4 (BSP) 109-91 -92-93 -94 - -96-97 1 1/4 Inch Straight 1 1/16 O-ring 0-1074 -1075-10 -1077-107 -1079-100 -22 3/4 inch Split Flange 0-1001 -1040-1002 -1003-1041 -1042-1043 Wheel Motor Bearingless * New Release 40 mm Straight G 3/4 (BSP) 0-0 -09-10 - -12-13 -25 1 5/ Inch Tapered 1 1/4 Inch T Splined 1 1/16 O-ring 0-101 -102-103 -104-105 -106-107 16-3/4 inch Split Flange 0-1006 -1044-1007 -100-10 -1046-1047 1 1/16 O-ring 0-10 -109-10 -1091-1092 -1093-1094 3/4 inch Split Flange 0-10 -104-1012 -1013-1049 -0-1 1 1/16 O-ring 1-1033 -1034-10 -1036-1037 -10-1039 -1062-1063 3/4 inch Split Flange 1-1044 -10-10 -1046-1016 -10-101 G 3/4 (BSP) 1-2 -3-4 -5-6 -7-1-7 Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 16
Model Code The following -digit coding system has been developed to identify all of the configuration options for the motor. Use this model code to specify a motor with the desired features. All digits of the code must be present when ordering. You may want to photocopy the matrix below to ensure that each number is entered in the correct box. M 0 4 * ** ** * * ** ** * ** * * ** ** ** ** ** * 1 2 3 4 5 6 7 9 10 12 13 16 1 19 20 21 22 24 25 26 27 2 29 1 Product M - Motor 2, 3 Series 04 4, 5, 6 Displacement cm3/r [in3/r] 067-109. cm 3 /r [6. in 3 /r] 00-1.3 cm 3 /r [7. in 3 /r] 099-162.2 cm 3 /r [9. in 3 /r] 125-205.5 cm 3 /r [12.54 in 3 /r] 0-246.3 cm 3 /r [.03 in 3 /r] 1-20.1 cm 3 /r [.09 in 3 /r] 1-3. cm 3 /r [19.03 in 3 /r] - 369.0 cm 3 /r [22.52 in 3 /r] 240-393.9 cm 3 /r [24.04 in 3 /r] 1-492.6 cm 3 /r [.06 in 3 /r] 342-560.2 cm 3 /r [34.1 in 3 /r] 1-6.9 cm 3 /r [.07 in 3 /r] 7, Mounting Type AA Bearingless, 4 Bolt: 127.00 [5.000] Pilot Dia..27 [.562] Dia. Holes on 1.92 [6.375] Dia. Bolt Circle AB Standard, 4 Bolt: 101.60 [4.000] Pilot Dia..7 [.5] Slots on 127.00 [5.000] Dia. Bolt Circle. (SAE B) AC Wheel, 4 Bolt: 139. [5.500] Pilot Dia..27 [.562] Dia. Holes on 165.10 [6.500] Dia. Bolt Circle. AD Wheel, 4 Bolt: 127.00 [5.000] Pilot Dia..500-13 UNC-2B Threaded Holes on 7.62 [5.12] Dia. Bolt circle. AF Standard, 4 Bolt: 127.00 [5.000] Pilot Dia..27 [.562] Dia. Holes on 1.92 [6.375] Dia. Bolt Circle. (SAE C) AH Standard: ISO Flange 125 B4hw (ISO 19/2) 124.97 [4.920] Pilot Dia..27 [.562] Dia. Holes on 160.00 [6.299] Dia. Bolt Circle AP Wheel, 4 Bolt: 160.0 [6.] Pilot Dia. with 5. [.] Pilot Length and 1.00 [.9] Dia Holes on 200.00 [7.74] Bolt Circle (ISO Compatible) 9, 10 Output Shaft 00 None (Bearingless) 01 31.75 [1.250] Dia. Straight With.375-16UNC- 2B Thread,.1 [2.09] Max Coupling Length, 7.9 [.3125] Sq x 41.27 [1.625] Straight Key 02 41.2 [1.625] Dia. Tapered with.2 [.4375] Sq x 31.75 [1.250] Straight Key, 1.250-1UNEF-2A Thread with Slotted Hex Nut 03 31.75 [1.250] Dia. Flat Root Side Fit, Tooth, 12/24 DP Involute Spline,.1 [1.50] Minimum Full Spline Length with.375-16unc-2b Thread 10.10 [1.500] Dia. Flat Root Side Fit, Tooth, 12/24 DP. Involute Spline, 31.2 [1.] Minimum Full Spline Length, with.375-16 UNC-2B Thread in End 40.00 [1.575] Dia. Straight with M12 x 1.75-6H Thread, 7.5 [.3132] x.979 [.4716] Wide X 69.9 [2.755] Straight Key 21 40.00 [1.575] Dia. 10:1 Tapered Shaft per ISO R775 with.750-16 UNF-2B Threaded in End, 12W x H L [.472W x.313h x 2.L] Key 22 None (Bearingless) European Spline 25 42.00 [1.654] Dia. 10:1 Tapered Shaft per ISO R775 with.750-16 UNF-2B Thread in End, 12W x H X 63L [.472W X.313H X 2.4L] Key, 12 Ports AA.75- UNF-2B SAE O-Ring Ports - Staggered Ports AB 1.0625-12 UN-2B SAE O-Ring Ports - Staggered Ports AC G 3/4 Ports - Staggered Ports AD 19.05 [.750] 4 Bolt Split Flange Staggered Ports Standard Pressure Series (Code ) AE M22 X 1.5-6H O-Ring Port - Staggered Ports AG 12. [.500] Dia. Manifold Ports AJ Dash 12 Stc Type II+ (Snap to Connect) Ports - Staggered Ports 13, Case Flow Options 00 None 01.5625-1 UNF-2B SAE O-Ring Port with Shuttle 02.4375-20 UNF-2B SAE O-ring Port with Check Valve 03 G 1/4 BSP Straight Thread with Check Valve 06.4375-20 UNF-2B SAE O-ring Port with Reverse Flow Shuttle 10 Dash 6 Stc Type II + (Snap to Connect) Port Low Pressure Relief 0 None A Set at 4.5 Bar [65 lbf/in 2 ] B Set at.2 Bar [220 lbf/in 2 ] 16, Pressure/Flow Option 00 None 1 Geroler Option 0 Standard 19 Seal Option 0 Standard 1 Viton 4 Seal Guard 20, 21 Accessories 00 None AC M 12 Threaded Connector, Long Body Digital Speed and Direction Pickup (Two 36 Pulse Signals in Quadrature per Revolution Pin 1=Power Supply, Pin 2=Output Signal 1, Pin 3=Common, Pin 4=Output Signal 2) AD M 12 Threaded Connector, Digital Speed And Direction Pickup (One 72 Pulse per Rev Speed Signal and One Directional Signal (Pin 1=Power, Pin 2=Direction, Pin 2=Common, Pin 4=Speed) 22, Special Features (Hardware) 00 None Low Noise Valve Plate 24, 25 Special Features (Assembly) 00 None 26, 27 Paint/Packaging 00 No Paint, Individual Box AA Painted Low Gloss Black, Individual Box AB Epoxy Coated (Frost Gray), Individual Box 2, 29 Customer Identification 00 None Design Code F Sixth Feature in bold are preferred and allow for shorter lead time. Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9
Order Numbers FT Article Number Eaton Code Type 124741 109-1002 CHAR-LYNN MOTOR SERIE 0 124742 109-2 CHAR-LYNN MOTOR SERIE 0 13172 109-3 CHAR-LYNN MOTOR SERIE 0 124743 109-5 CHAR-LYNN MOTOR SERIE 0 1247 109-1065 CHAR-LYNN MOTOR SERIE 0 1 109-00 CHAR-LYNN MOTOR SERIE 0 124746 109-02 CHAR-LYNN MOTOR SERIE 0 1667 109-03 CHAR-LYNN MOTOR SERIE 0 1317 109-04 CHAR-LYNN MOTOR SERIE 0 12474 109-1 CHAR-LYNN MOTOR SERIE 0 139 109-12 CHAR-LYNN MOTOR SERIE 0 12596 109-13 CHAR-LYNN MOTOR SERIE 0 3 109- CHAR-LYNN MOTOR SERIE 0 124750 109-16 CHAR-LYNN MOTOR SERIE 0 124751 109- CHAR-LYNN MOTOR SERIE 0 139 109-1 CHAR-LYNN MOTOR SERIE 0 124752 109-19 CHAR-LYNN MOTOR SERIE 0 1247 109-1 CHAR-LYNN MOTOR SERIE 0 312 109-1 CHAR-LYNN MOTOR SERIE 0 124754 109-13 CHAR-LYNN MOTOR SERIE 0 124755 109-4 CHAR-LYNN MOTOR SERIE 0 124756 109-5 CHAR-LYNN MOTOR SERIE 0 124759 109-9 CHAR-LYNN MOTOR SERIE 0 1240 109- CHAR-LYNN MOTOR SERIE 0 262 109- (LOW LEAKAGE) CHAR-LYNN MOTOR SERIE 0 34019 109--VITON CHAR-LYNN MOTOR SERIE 0 1241 109-91 CHAR-LYNN MOTOR SERIE 0 1242 109-92 CHAR-LYNN MOTOR SERIE 0 1243 109-93 CHAR-LYNN MOTOR SERIE 0 1244 109-94 CHAR-LYNN MOTOR SERIE 0 13104 109- CHAR-LYNN MOTOR SERIE 0 1245 109-96 CHAR-LYNN MOTOR SERIE 0 2025 109-1216 CHAR-LYNN MOTOR SERIE 0 1246 109-1224 CHAR-LYNN MOTOR SERIE 0 1247 109-1 CHAR-LYNN MOTOR SERIE 0 124 109-1227 CHAR-LYNN MOTOR SERIE 0 1249 109- CHAR-LYNN MOTOR SERIE 0 1247 109- CHAR-LYNN MOTOR SERIE 0 124771 109-12 CHAR-LYNN MOTOR SERIE 0 124772 109-16 CHAR-LYNN MOTOR SERIE 0 3159 109-1243 CHAR-LYNN MOTOR SERIE 0 124773 109-12 CHAR-LYNN MOTOR SERIE 0 124774 109-1246 CHAR-LYNN MOTOR SERIE 0 206 109-1246-K CHAR-LYNN MOTOR SERIE 0 124775 109-1247 CHAR-LYNN MOTOR SERIE 0 1247 109-124 CHAR-LYNN MOTOR SERIE 0 124777 109-1249 CHAR-LYNN MOTOR SERIE 0 12477 109-1250 CHAR-LYNN MOTOR SERIE 0 26575 109-1257 CHAR-LYNN MOTOR SERIE 0 267 109-125 CHAR-LYNN MOTOR SERIE 0 2567 109-1259 CHAR-LYNN MOTOR SERIE 0 124779 109-12 CHAR-LYNN MOTOR SERIE 0 Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 1
Order Numbers FT Article Number Eaton Code Type 460 109-1265 CHAR-LYNN MOTOR SERIE 0 12470 109-1267 CHAR-LYNN MOTOR SERIE 0 12471 109-1291 CHAR-LYNN MOTOR SERIE 0 12472 109-16 CHAR-LYNN MOTOR SERIE 0 12473 109-19 CHAR-LYNN MOTOR SERIE 0 12474 109-1336 CHAR-LYNN MOTOR SERIE 0 12475 109-13 CHAR-LYNN MOTOR SERIE 0 12476 109-1362 CHAR-LYNN MOTOR SERIE 0 393 109-13 CHAR-LYNN MOTOR SERIE 0 2565 109-32 CHAR-LYNN MOTOR SERIE 0 243 109-10 CHAR-LYNN MOTOR SERIE 0 310 109-60 CHAR-LYNN MOTOR SERIE 0 427 109-73 CHAR-LYNN MOTOR SERIE 0 3 109-7 CHAR-LYNN MOTOR SERIE 0 2022 109-97 CHAR-LYNN MOTOR SERIE 0 2024 109-9 CHAR-LYNN MOTOR SERIE 0 9 109-99 CHAR-LYNN MOTOR SERIE 0 31210 109-42 CHAR-LYNN MOTOR SERIE 0 2522 109-50 CHAR-LYNN MOTOR SERIE 0 27499 109-75 CHAR-LYNN MOTOR SERIE 0 319 109-2 CHAR-LYNN MOTOR SERIE 0 312 109-16 CHAR-LYNN MOTOR SERIE 0 746 109-1659 CHAR-LYNN MOTOR SERIE 0 124799 0-1006 CHAR-LYNN MOTOR SERIE 0 12 0-1073 CHAR-LYNN MOTOR SERIE 0 1253 0-101 CHAR-LYNN MOTOR SERIE 0 1254203 0-102 CHAR-LYNN MOTOR SERIE 0 16719 0-104 CHAR-LYNN MOTOR SERIE 0 12402 0-105 CHAR-LYNN MOTOR SERIE 0 12663 0-106 CHAR-LYNN MOTOR SERIE 0 221 0-09 CHAR-LYNN MOTOR SERIE 0 240 0-10 CHAR-LYNN MOTOR SERIE 0 103 0- CHAR-LYNN MOTOR SERIE 0 12406 0-12 CHAR-LYNN MOTOR SERIE 0 27294 0-13 CHAR-LYNN MOTOR SERIE 0 13322 0-29 CHAR-LYNN MOTOR SERIE 0 2092 0- CHAR-LYNN MOTOR SERIE 0 07794 1-2 CHAR-LYNN MOTOR SERIE 0 916 1-3 CHAR-LYNN MOTOR SERIE 0 07799 1-4 CHAR-LYNN MOTOR SERIE 0 26 1-5 CHAR-LYNN MOTOR SERIE 0 2654 1-6 CHAR-LYNN MOTOR SERIE 0 34071 1-1079 CHAR-LYNN MOTOR SERIE 0 2652 1-106 CHAR-LYNN MOTOR SERIE 0 Fon: +49 (0) 21 51-9-0 Fax: +49 (0) 21 51-9-9 19