A revolution in stainless steel turning

ISO Insert Series for Stainless Steel Turning TOOLS NEWS A revolution in stainless steel turning Excellent resistance to notch wear and with good burr control. Long tool life achieved due to high plastic deformation resistance. NEW - 5º and 7º positive inserts now included. 2013.4 Update B201G Series Expansion GM A

ISO insert Series for Stainless Steel Turning CVD coated grade / PVD coated grade az ax ac av zsmooth cutting edge Prevents welding xthin layer, Nano-texture Al2O3 Controls abnormal damage ctough, Nano-texture TiCN High wear resistance vspecial carbide Newly developed substrate Plastic deformation resistance Chipping resistance az ax z(al, Ti)N coating Prevents welding xspecial carbide substrate Improved fracture resistance Thermal shock resistance Application range Concept of grade ISO Category Codes M01 M10 M20 M30 M40 NEW Stainless Steel NEW NEW Wear resistance New CVD grade Conventional CVD grade US7020 New PVD grade US735 Stability of the cutting edge 1

Breaker system for stainless steel turning (Negative inserts) 7.0 6.0 5.0 Chip control range M Stainless Steel Negative insert for external turning Depth of cut (mm) 4.0 3.0 2.0 GM ycutting CONDITIONS 1.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 Feed rate (mm/rev) Continuous Cutting Constant Depth of Cut Pre-machined Surfaces Securely Clamped Component Cutting Heavy Interrupted Cutting Irregular Depth of Cut Low Clamping Rigidity Cutting Main breaker breaker for light cutting Excellent burr control duces the incidence of burrs drastically because the sharpness properties and cutting edge strength are optimized with different rake angles. Nose Flank 15 20 0.50 Sub breaker GM breaker Sub breaker of the main and chip breaker. Excellent in notching resistance for light cutting to medium cutting. Nose 25 15 0.5 breaker for medium cutting Excellent resistance to plastic deformation As a result of obtaining the optimum land geometry by simulation analysis technology, the plastic deformation of the insert corner was controlled and achieved long tool life. breaker for rough cutting Excellent fracture resistance By optimizing the land angle and honing geometry, high cutting edge stability is achieved during interrupted machining. 6 Nose 10 Flank 3 Nose 6 Flank 0.3 0.3 0.32 0.32 25 0.5 Flank 15 Multi-Assist breaker MA breaker Suitable for medium cutting range. 22 0.2 Nose 6 22 0.2 Flank 6 2

ISO insert Series for Stainless Steel Turning Breaker system for stainless steel turning (Positive inserts) 4.0 Chip control range M Stainless Steel Positive Insert 3.0 Depth of cut (mm) 2.0 1.0 ycutting CONDITIONS 0.1 0.2 Feed rate (mm/rev) 0.3 0.4 Continuous Cutting Constant Depth of Cut Pre-machined Surfaces Securely Clamped Component Cutting Heavy Interrupted Cutting Irregular Depth of Cut Low Clamping Rigidity Cutting Main breaker breaker for light cutting First recommendation for light cutting of stainless steel The large rake angle gives a sharp cutting edge that prevents chip welding, which in turn helps to control the surface finish. The protruding chipbreaker provides an ideal range of chip control. 5 Positive Insert 18 8 Nose Flank breaker for medium cutting First recommendation for medium cutting of stainless steel The flat land enables a good balance of wear and fracture resistance. The wide pocket reduces vibration and chip jamming and also prevents increases in cutting resistance even at large depths of cut. 5 Positive Insert 18 18 Nose 0.1 Flank 0.1 3

Cutting performance a Wear resistance comparison Tool life comparison was made at a 1mm depth of cut where burrs were most likely to occur. Long tool life was achieved. grade with the chipbreaker demonstrated good burr control and gave long tool life. 0.60 <Cutting conditions> Inserts : CNMG120408-oo Work piece : SUS304 (170HB) Cutting speed : 300m/min Feed rate : 0.2mm/rev Depth of cut : 1.0mm Coolant : Wet cutting a Wear resistance comparison + Conventional 0.40 Flank wear (mm) 0.50 0.40 0.30 Conventional B 0.20 Conventional A 0.10 0 0 2 4 6 8 10 12 Cutting time (min) <Cutting conditions> Inserts : CNMG120408-oo Work piece : SUS304 Cutting speed : 180m/min Feed rate : 0.35mm/rev Depth of cut : 4.0mm Coolant : Wet cutting Flank wear (mm) 0.30 0.20 0.10 0 0 2 4 6 8 Cutting time (min) a Fracture resistance comparison Fracture resistance was tested by turning a component with a slot. (Impact frequency: 150/pass) + Conventional Notch wear and large welding a Fracture resistance comparison Fracture resistance was tested by turning a component with a slot. (Impact frequency: 300/pass) GM+ Conventional CVD grade Conventional PVD grade Chipping Chipping <Cutting conditions> Inserts : CNMG120408-oo Work piece : SUS304 Cutting speed : 120m/min Feed rate : 0.3mm/rev Depth of cut : 2.0mm Coolant : Wet cutting <Cutting conditions> Inserts : CNMG120408-oo Work piece : SUS316 Cutting speed : 50m/min Feed rate : 0.15mm/rev Depth of cut : 1.0mm Coolant : Wet cutting 4

ISO insert Series for Stainless Steel Turning INSERTS a Negative Inserts (With hole) Shape Order Number Stock Dimensions (mm) D2 CNMG120404- a a a 12.7 4.76 0.4 5.16 120408- a a a 12.7 4.76 0.8 5.16 120412- a a a 12.7 4.76 1.2 5.16 Geometry GM CNMG120408- a a a 12.7 4.76 0.8 5.16 120412- a a a 12.7 4.76 1.2 5.16 120416- a a a 12.7 4.76 1.6 5.16 160608- a a a 15.875 6.35 0.8 6.35 160612- a a a 15.875 6.35 1.2 6.35 160616- a a a 15.875 6.35 1.6 6.35 190608- a a a 19.05 6.35 0.8 7.93 190612- a a a 19.05 6.35 1.2 7.93 190616- a a a 19.05 6.35 1.6 7.93 CNMG120408- a a a 12.7 4.76 0.8 5.16 120412- a a a 12.7 4.76 1.2 5.16 120416- a a a 12.7 4.76 1.6 5.16 160612- a a a 15.875 6.35 1.2 6.35 160616- a a a 15.875 6.35 1.6 6.35 190612- a a a 19.05 6.35 1.2 7.93 190616- a a a 19.05 6.35 1.6 7.93 CNMG120404-GM a a a 12.7 4.76 0.4 5.16 120408-GM a a a 12.7 4.76 0.8 5.16 120412-GM a a a 12.7 4.76 1.2 5.16 MA CNMG120404-MA a a 12.7 4.76 0.4 5.16 120408-MA a a 12.7 4.76 0.8 5.16 120412-MA a a 12.7 4.76 1.2 5.16 DNMG110404- a a a 9.525 4.76 0.4 3.81 110408- a a a 9.525 4.76 0.8 3.81 150404- a a a 12.7 4.76 0.4 5.16 150408- a a a 12.7 4.76 0.8 5.16 150412- a a a 12.7 4.76 1.2 5.16 150604- a a a 12.7 6.35 0.4 5.16 150608- a a a 12.7 6.35 0.8 5.16 150612- a a a 12.7 6.35 1.2 5.16 DNMG150408- a a a 12.7 4.76 0.8 5.16 150412- a a a 12.7 4.76 1.2 5.16 150608- a a a 12.7 6.35 0.8 5.16 150612- a a a 12.7 6.35 1.2 5.16 55 55 5 a : Inventory maintained.

Stock Dimensions (mm) Shape Order Number D2 Geometry GM MA DNMG150408- a a a 12.7 4.76 0.8 5.16 150412- a a a 12.7 4.76 1.2 5.16 150416- a a a 12.7 4.76 1.6 5.16 150608- a a a 12.7 6.35 0.8 5.16 150612- a a a 12.7 6.35 1.2 5.16 150616- a a a 12.7 6.35 1.6 5.16 DNMG150404-GM a a a 12.7 4.76 0.4 5.16 150408-GM a a a 12.7 4.76 0.8 5.16 150412-GM a a a 12.7 4.76 1.2 5.16 150604-GM a a a 12.7 6.35 0.4 5.16 150608-GM a a a 12.7 6.35 0.8 5.16 150612-GM a a a 12.7 6.35 1.2 5.16 DNMG150404-MA a a 12.7 4.76 0.4 5.16 150408-MA a a 12.7 4.76 0.8 5.16 150412-MA a a 12.7 4.76 1.2 5.16 150604-MA a a 12.7 6.35 0.4 5.16 150608-MA a a 12.7 6.35 0.8 5.16 150612-MA a a 12.7 6.35 1.2 5.16 SNMG120404- a a a 12.7 4.76 0.4 5.16 120408- a a a 12.7 4.76 0.8 5.16 55 55 55 GM SNMG120408- a a a 12.7 4.76 0.8 5.16 120412- a a a 12.7 4.76 1.2 5.16 120416- a a a 12.7 4.76 1.6 5.16 150608- a a a 15.875 6.35 0.8 6.35 150612- a a a 15.875 6.35 1.2 6.35 150616- a a a 15.875 6.35 1.6 6.35 190612- a a a 19.05 6.35 1.2 7.93 190616- a a a 19.05 6.35 1.6 7.93 SNMG120408- a a a 12.7 4.76 0.8 5.16 120412- a a a 12.7 4.76 1.2 5.16 120416- a a a 12.7 4.76 1.6 5.16 150612- a a a 15.875 6.35 1.2 6.35 150616- a a a 15.875 6.35 1.6 6.35 190612- a a a 19.05 6.35 1.2 7.93 190616- a a a 19.05 6.35 1.6 7.93 SNMG120404-GM a a a 12.7 4.76 0.4 5.16 120408-GM a a a 12.7 4.76 0.8 5.16 120412-GM a a a 12.7 4.76 1.2 5.16 6

ISO insert Series for Stainless Steel Turning INSERTS a Negative Inserts (With hole) Shape MA Order Number Stock Dimensions (mm) D2 SNMG120404-MA a a 12.7 4.76 0.4 5.16 120408-MA a a 12.7 4.76 0.8 5.16 120412-MA a a 12.7 4.76 1.2 5.16 Geometry TNMG160404- a a a 9.525 4.76 0.4 3.81 160408- a a a 9.525 4.76 0.8 3.81 160412- a a a 9.525 4.76 1.2 3.81 GM MA TNMG160408- a a a 9.525 4.76 0.8 3.81 160412- a a a 9.525 4.76 1.2 3.81 220408- a a a 12.7 4.76 0.8 5.16 220412- a a a 12.7 4.76 1.2 5.16 220416- a a a 12.7 4.76 1.6 5.16 TNMG160408- a a a 9.525 4.76 0.8 3.81 160412- a a a 9.525 4.76 1.2 3.81 220408- a a a 12.7 4.76 0.8 5.16 220412- a a a 12.7 4.76 1.2 5.16 220416- a a a 12.7 4.76 1.6 5.16 TNMG160404-GM a a a 9.525 4.76 0.4 3.81 160408-GM a a a 9.525 4.76 0.8 3.81 160412-GM a a a 9.525 4.76 1.2 3.81 220408-GM a a a 12.7 4.76 0.8 5.16 220412-GM a a a 12.7 4.76 1.2 5.16 TNMG160404-MA a a 9.525 4.76 0.4 3.81 160408-MA a a 9.525 4.76 0.8 3.81 160412-MA a a 9.525 4.76 1.2 3.81 220408-MA a a 12.7 4.76 0.8 5.16 220412-MA a a 12.7 4.76 1.2 5.16 VNMG160404- a a a 9.525 4.76 0.4 3.81 160408- a a a 9.525 4.76 0.8 3.81 35 VNMG160408- a a a 9.525 4.76 0.8 3.81 35 7 a : Inventory maintained.

Stock Dimensions (mm) Shape Order Number D2 Geometry GM VNMG160404-GM a a a 9.525 4.76 0.4 3.81 160408-GM a a a 9.525 4.76 0.8 3.81 35 MA VNMG160404-MA a a 9.525 4.76 0.4 3.81 160408-MA a a 9.525 4.76 0.8 3.81 35 WNMG060404- a a a 9.525 4.76 0.4 3.81 060408- a a a 9.525 4.76 0.8 3.81 080404- a a a 12.7 4.76 0.4 5.16 080408- a a a 12.7 4.76 0.8 5.16 WNMG060408- a a a 9.525 4.76 0.8 3.81 060412- a a a 9.525 4.76 1.2 3.81 080408- a a a 12.7 4.76 0.8 5.16 080412- a a a 12.7 4.76 1.2 5.16 WNMG060408- a a a 9.525 4.76 0.8 3.81 060412- a a a 9.525 4.76 1.2 3.81 080408- a a a 12.7 4.76 0.8 5.16 080412- a a a 12.7 4.76 1.2 5.16 GM MA WNMG060404-GM a a a 9.525 4.76 0.4 3.81 060408-GM a a a 9.525 4.76 0.8 3.81 080404-GM a a a 12.7 4.76 0.4 5.16 080408-GM a a a 12.7 4.76 0.8 5.16 080412-GM a a a 12.7 4.76 1.2 5.16 WNMG060408-MA a a 9.525 4.76 0.8 3.81 060412-MA a a 9.525 4.76 1.2 3.81 080404-MA a a 12.7 4.76 0.4 5.16 080408-MA a a 12.7 4.76 0.8 5.16 080412-MA a a 12.7 4.76 1.2 5.16 8

ISO insert Series for Stainless Steel Turning INSERTS a5 Positive inserts (With hole) Stock Dimensions (mm) Shape Order Number D2 Geometry VBMT110304- a u 6.35 3.18 0.4 2.9 110308- a u 6.35 3.18 0.8 2.9 160404- a u 9.525 4.76 0.4 4.4 160408- a u 9.525 4.76 0.8 4.4 35 VBMT160404- a u 9.525 4.76 0.4 4.4 160408- a u 9.525 4.76 0.8 4.4 35 5 a Positive inserts (With hole) Stock Dimensions (mm) Shape Order Number D2 Geometry CCMT060204- a u 6.35 2.38 0.4 2.8 060208- a u 6.35 2.38 0.8 2.8 09T304- a u 9.525 3.97 0.4 4.4 09T308- a u 9.525 3.97 0.8 4.4 CCMT060204- a u 6.35 2.38 0.4 2.8 060208- a u 6.35 2.38 0.8 2.8 09T304- a u 9.525 3.97 0.4 4.4 09T308- a u 9.525 3.97 0.8 4.4 120404- a u 12.7 4.76 0.4 5.5 120408- a u 12.7 4.76 0.8 5.5 120412- a u 12.7 4.76 1.2 5.5 DCMT070204- a u 6.35 2.38 0.4 2.8 070208- a u 6.35 2.38 0.8 2.8 11T304- a u 9.525 3.97 0.4 4.4 11T308- a u 9.525 3.97 0.8 4.4 55 DCMT070204- a u 6.35 2.38 0.4 2.8 070208- a u 6.35 2.38 0.8 2.8 11T304- a u 9.525 3.97 0.4 4.4 11T308- a u 9.525 3.97 0.8 4.4 150404- a u 12.7 4.76 0.4 5.5 150408- a u 12.7 4.76 0.8 5.5 SCMT09T304- a u 9.525 3.97 0.4 4.4 SCMT09T308- a u 9.525 3.97 0.8 4.4 55 9 a : Inventory maintained.

Stock Dimensions (mm) Shape Order Number D2 Geometry SCMT09T304- a u 9.525 3.97 0.4 4.4 09T308- a u 9.525 3.97 0.8 4.4 120404- a u 12.7 4.76 0.4 5.5 120408- a u 12.7 4.76 0.8 5.5 TCMT090204- a u 5.56 2.38 0.4 2.5 090208- a u 5.56 2.38 0.8 2.5 110204- a u 6.35 2.38 0.4 2.8 110208- a u 6.35 2.38 0.8 2.8 16T304- a u 9.525 3.97 0.4 4.4 16T308- a u 9.525 3.97 0.8 4.4 TCMT090204- a u 5.56 2.38 0.4 2.5 090208- a u 5.56 2.38 0.8 2.5 110204- a u 6.35 2.38 0.4 2.8 110208- a u 6.35 2.38 0.8 2.8 130304- a u 7.94 3.18 0.4 3.4 16T304- a u 9.525 3.97 0.4 4.4 16T308- a u 9.525 3.97 0.8 4.4 16T312- a u 9.525 3.97 1.2 4.4 VCMT110304- a u 6.35 3.18 0.4 2.8 110308- a u 6.35 3.18 0.8 2.8 160404- a u 9.525 4.76 0.4 4.4 160408- a u 9.525 4.76 0.8 4.4 35 VCMT160404- a u 9.525 4.76 0.4 4.4 160408- a u 9.525 4.76 0.8 4.4 160412- a u 9.525 4.76 1.2 4.4 35 10

ISO insert Series for Stainless Steel Turning RECOENDED CUTTING CONDITIONS y Negative Inserts (External turning tools) Work Material Hardness Cutting Conditions Cutting Range Breaker Grade Cutting Speed (m/min) Feed Rate (mm/rev) Depth of Cut (mm) M 180 285 0.10 0.30 0.30 2.00 160 255 0.15 0.45 0.70 5.00 155 245 0.25 0.55 1.50 6.00 Austenitic Stainless Steel (SUS304, SUS316) 200HB 160 215 0.10 0.30 0.30 2.00 145 195 0.15 0.45 0.70 5.00 140 185 0.25 0.55 1.50 6.00 95 155 0.10 0.30 0.30 2.00 85 140 0.15 0.45 0.70 5.00 85 135 0.25 0.55 1.50 6.00 150 240 0.10 0.30 0.30 2.00 135 215 0.15 0.45 0.70 5.00 130 205 0.25 0.55 1.50 6.00 Austenitic Stainless Steel (SUS304LN, SUS316LN) >200HB 135 180 0.10 0.30 0.30 2.00 125 165 0.15 0.45 0.70 5.00 115 155 0.25 0.55 1.50 6.00 80 130 0.10 0.30 0.30 2.00 75 120 0.15 0.45 0.70 5.00 70 115 0.25 0.55 1.50 6.00 120 195 0.10 0.30 0.30 2.00 110 175 0.15 0.45 0.70 5.00 105 165 0.25 0.55 1.50 6.00 Duplex Stainless Steel (SUS329J1) 280HB 110 150 0.10 0.30 0.30 2.00 100 135 0.15 0.45 0.70 5.00 95 125 0.25 0.55 1.50 6.00 65 105 0.10 0.30 0.30 2.00 60 95 0.15 0.45 0.70 5.00 55 90 0.25 0.55 1.50 6.00 180 285 0.10 0.30 0.30 2.00 160 255 0.15 0.45 0.70 5.00 155 245 0.25 0.55 1.50 6.00 Ferritic and Martensitic Stainless Steels (SUS410, SUS430) 200HB 160 215 0.10 0.30 0.30 2.00 145 195 0.15 0.45 0.70 5.00 140 185 0.25 0.55 1.50 6.00 95 155 0.10 0.30 0.30 2.00 85 140 0.15 0.45 0.70 5.00 85 135 0.25 0.55 1.50 6.00 11

Work Material Hardness Cutting Conditions Cutting Range Breaker Grade Cutting Speed (m/min) Feed Rate (mm/rev) Depth of Cut (mm) M 150 240 0.10 0.30 0.30 2.00 135 215 0.15 0.45 0.70 5.00 130 205 0.25 0.55 1.50 6.00 Ferritic and Martensitic Stainless Steels (SUS431, SUS420J2) >200HB 135 180 0.10 0.30 0.30 2.00 125 165 0.15 0.45 0.70 5.00 115 155 0.25 0.55 1.50 6.00 80 130 0.10 0.30 0.30 2.00 75 120 0.15 0.45 0.70 5.00 70 115 0.25 0.55 1.50 6.00 100 160 0.10 0.30 0.30 2.00 90 145 0.15 0.45 0.70 5.00 85 135 0.25 0.55 1.50 6.00 Hardened Stainless Steels (SUS630, SUS631) <450HB 90 120 0.10 0.30 0.30 2.00 80 110 0.15 0.45 0.70 5.00 80 105 0.25 0.55 1.50 6.00 55 85 0.10 0.30 0.30 2.00 50 80 0.15 0.45 0.70 5.00 45 75 0.25 0.55 1.50 6.00 12

ISO insert Series for Stainless Steel Turning RECOENDED CUTTING CONDITIONS y Positive Insert (External turning tools) Work Material Hardness Cutting Conditions Cutting Range Breaker Grade Cutting Speed (m/min) Feed Rate (mm/rev) Depth of Cut (mm) M 140 190 0.06 0.25 0.20 1.00 115 155 0.08 0.30 0.30 2.00 Austenitic Stainless Steel (SUS304, SUS316) 200HB 140 190 0.06 0.25 0.20 1.00 115 155 0.08 0.30 0.30 2.00 85 135 0.06 0.25 0.20 1.00 70 115 0.08 0.30 0.30 2.00 120 160 0.06 0.25 0.20 1.00 100 130 0.08 0.30 0.30 2.00 Austenitic Stainless Steel (SUS304LN, SUS316LN) >200HB 120 160 0.06 0.25 0.20 1.00 100 130 0.08 0.30 0.30 2.00 70 115 0.06 0.25 0.20 1.00 60 95 0.08 0.30 0.30 2.00 95 130 0.06 0.25 0.20 1.00 80 105 0.08 0.30 0.30 2.00 Duplex Stainless Steel (SUS329J1) 280HB 95 130 0.06 0.25 0.20 1.00 80 105 0.08 0.30 0.30 2.00 55 95 0.06 0.25 0.20 1.00 45 75 0.08 0.30 0.30 2.00 140 190 0.06 0.25 0.20 1.00 115 155 0.08 0.30 0.30 2.00 Ferritic and Martensitic Stainless Steels (SUS410, SUS430) 200HB 140 190 0.06 0.25 0.20 1.00 115 155 0.08 0.30 0.30 2.00 85 135 0.06 0.25 0.20 1.00 70 115 0.08 0.30 0.30 2.00 120 160 0.06 0.25 0.20 1.00 100 130 0.08 0.30 0.30 2.00 Ferritic and Martensitic Stainless Steels (SUS431, SUS420J2) >200HB 120 160 0.06 0.25 0.20 1.00 100 130 0.08 0.30 0.30 2.00 70 115 0.06 0.25 0.20 1.00 60 95 0.08 0.30 0.30 2.00 80 105 0.06 0.25 0.20 1.00 65 90 0.08 0.30 0.30 2.00 Hardened Stainless Steel (SUS630, SUS631) <450HB 80 105 0.06 0.25 0.20 1.00 65 90 0.08 0.30 0.30 2.00 45 75 0.06 0.25 0.20 1.00 40 65 0.08 0.30 0.30 2.00 * commended cutting conditions for 7º positive inserts are provided as a guideline only. Verify the recommended conditions for each boring bar as cutting conditions for internal machining will vary depending on the length of overhang. 13

EXAMPLES OF USAGE Insert WNMG080408- CNMG160612- CNMG120408- SC3 (Stainless Cast Steel) SUS329J3L SUS321 Work Piece Cutting Conditions Cutting Speed (m/min) 145 50 220 Feed Rate (mm/rev) 0.13 0.45 0.28 Depth of Cut (mm) 2.0 4.0 1.6 Coolant Wet Wet Wet Competitor s Competitor s Competitor s sults Fracture 5 pieces machined 10 pieces machined 8 pieces machined 8 pieces machined 4 pieces machined 8 pieces machined Insert CNMG120408- WNMG080408- CNMG120408- SUS836L (Austenitic Stainless Steel) SUS316 SUS304 Work Piece Cutting Conditions Cutting Speed (m/min) 70 122 80 Feed Rate (mm/rev) 0.2 0.3 0.1 Depth of Cut (mm) 1.1 2.2 2 Coolant Wet Wet Wet Competitor s Competitor s Competitor s sults 12 pieces machined 15 pieces machined 60 pieces machined 60 pieces machined 5 pieces machined 5 pieces machined 14

For Your Safety adon't handle inserts and chips without gloves. aplease machine within the recommended application range and exchange expired tools with new ones in advance of breakage. aplease use safety covers and wear safety glasses. awhen using compounded cutting oils, please take fire precautions. awhen attaching inserts or spare parts, please use only the correct wrench or driver. awhen using rotating tools, please make a trial run to check run-out, vibration and abnormal sounds etc. MITSUBISHI MATERIALS CORPORATION Overseas Sales Dept, Asian gion KFC bldg., 8F, 1-6-1 Yokoami, Sumida-ku, Tokyo 130-0015, Japan TEL +81-3-5819-8771 FAX +81-3-5819-8774 Overseas Sales Dept, European & American gion KFC bldg., 8F, 1-6-1 Yokoami, Sumida-ku, Tokyo 130-0015, Japan TEL +81-3-5819-8772 FAX +81-3-5819-8774 http://www.mitsubishicarbide.com/en/ (Tools specifications subject to change without notice.) EXP-12-E030 2017.4.( - )