Quik Referene Guide P/N 3300995, Rev. C April 2003 Model 3500 Trnsmitter (9-wire) or Model 3300 Peripherl Instlltion Instrutions for Rk-Mount For online tehnil support, use the EXPERT 2 system t www.expert2.om. To spek to ustomer servie representtive, ll the support enter nerest you: In the U.S.A., phone 1-800-522-MASS (1-800-522-6277) In Cnd nd Ltin Ameri, phone (303) 530-8400 In Asi, phone (65) 6770-8155 In the U.K., phone 0800-966 180 (toll-free) Outside the U.K., phone +31 (0) 318 495 67 TM Miro Motion
BEFORE YOU BEGIN This quik referene guide explins bsi instlltion guidelines for mounting the Miro Motion Model 3300/3500 pplitions pltform in 19-inh (486,2 mm) rk. For informtion on I.S. pplitions, refer to Miro Motion ATEX, UL, or CSA instlltion instrutions. For omplete instrutions bout onfigurtion, mintenne, nd servie, refer to the instrution mnul shipped with the trnsmitter. WARNING Improper instlltion in hzrdous re n use n explosion. For informtion bout hzrdous pplitions, refer to Miro Motion ATEX, UL, or CSA instlltion instrutions, shipped with the trnsmitter or vilble from the Miro Motion web site. WARNING Hzrdous voltge n use severe injury or deth. Instll trnsmitter nd omplete ll wiring before supplying power. CAUTION Improper instlltion ould use mesurement error or flowmeter filure. Follow ll instrutions to ensure trnsmitter will operte orretly. 2003, Miro Motion, In. All rights reserved. Miro Motion is registered trdemrk of Miro Motion, In. The Miro Motion nd Emerson logos re trdemrks of Emerson Eletri Co. All other trdemrks re property of their respetive owners. 1
Europen instlltions This Miro Motion produt omplies with ll pplible Europen diretives when properly instlled in ordne with the instrutions in this quik referene guide. Refer to the EC delrtion of onformity for diretives tht pply to this produt. The EC delrtion of onformity, with ll pplible Europen diretives, nd the omplete ATEX Instlltion Drwings nd Instrutions re vilble on the internet t www.miromotion.om/tex or through your lol Miro Motion support enter. Instlltion kit For mounting in rk, the Model 3300/3500 instlltion kit inludes the following prts: One DIN stndrd 41612, Type D onnetor for input/output wiring, with solder tils or srew terminls (Model 3500 only) One DIN stndrd 41612, keyed Type D onnetor for sensor wiring, with solder tils or srew terminls One plug-in onnetor for power supply wiring Four (Model 3300) or six (Model 3500) slotted heese-hed mhine srews, size M2.5x8, for seuring wiring onnetors to the rk STEP 1. Choosing lotion Choose lotion for the trnsmitter bsed on the requirements desribed below. Environmentl requirements Instll the trnsmitter where mbient temperture is between 4 nd +140 F ( 20 nd +60 C). If multiple pplitions pltforms re instlled, provide t lest 1 U (1 HE) of vertil spe between rks to ensure proper ventiltion. See Figure 1, pge 3. 2
Figure 1. Spe requirements for proper ventiltion 1 U = 1 HE = 1.750 inhes (44,5 mm) 3 U (3 HE) 1 U (1 HE) 3 U (3 HE) 1 U (1 HE) 3 U (3 HE) Dimensions The Model 3300/3500 hs the following dimensions (see Figure 2, pge 4): Height: 128 mm (3 U or 3 HE) Width: 142 mm (28 HP or 28 TE) Depth: 160 mm The Model 3300/3500 onforms to DIN stndrd 41494, Prt 5 (IEC 297-3) for 19-inh (486,2 mm) rks. Up to three enlosures fit into one rk. See Figure 1. 3
Figure 2. Dimensions for mounting in rk 1 U = 1 HE = 1.750 inhes (44,5 mm) 1 HP = 1 TE = 0.200 inh (5,1 mm) 25 HP (25 TE) 4 x M2.5x11 inhes (mm) 3 U (3 HE) 4 13/16 (122,5) 5 1/16 (128,5) 5.6 (142,2) 28 HP (28 TE) 19-inh (486,2 mm) rk onforms to DIN 41494, Prt 5, nd IEC 297-3. Not inluded with Model 3300/3500. Optionl srew terminl inhes (mm) Rer ril for mounting onnetors tht onform to DIN 41612 nd IEC 603-2. Not inluded with Model 3300/3500. Approvls tg Intrinsi sfety shield (Model 3500 only) 1 (25,4) 6 11/16 (169,9) 7 29/32 (200,6) 7 11/32 (186,7) 8 33/64 (216,2) Flowmeter ble lengths Mximum ble length from the sensor to the Model 3500 trnsmitter is 1000 feet (300 meters). If you re instlling the Model 3300 pplitions peripherl in ombintion with trnsmitter, the mximum ble length from the trnsmitter s frequeny output to the Model 3300 s frequeny input is 500 feet (150 meters). 4
STEP 2. Instlling guide rils nd wiring onnetors Guide rils Positions of guide rils nd wiring onnetors re indited in Figure 3, pge 6. Centers of guide rils should be 27 HP (27 TE) prt, for exmple, t 1 HP (TE) nd 28 HP (TE). Wiring onnetors The pplitions pltform is shipped with solder-til or srew-type onnetor for input/output wiring, keyed solder-til or srew-type onnetor for sensor wiring (Model 3500 only), nd plug-in onnetor for power supply wiring. Working from the front of the rk, use the supplied M2.5x8 srews to instll the wiring onnetors onto the bk of the rk s follows: 1. Use the enters of the guide rils s referene points nd refer to Figure 3, pge 6. 2. Instll the input/output wiring onnetor t 4 HP (4 TE) from the neighboring unit or from the edge of the rk. 3. (Model 3500 only) Instll the keyed sensor wiring onnetor t 16 HP (16 TE) from the neighboring unit or from the edge of the rk. 4. Instll the power supply wiring onnetor t 25 HP (25 TE) from the neighboring unit or from the edge of the rk. 5
Figure 3. Positions of guide rils nd wiring onnetors Instll srews nd onnetors from front of rk. Model 3500 hs six M2.5x8 srews nd three onnetors. Model 3300 hs four M2.5x8 srews nd two onnetors. Front Guide ril enters should be 27 HP (27 TE) prt; for exmple, 1 HP (1 TE) nd 28 HP (28 TE) Bk Keys on sensor wiring onnetor M2.5x8 Input/output wiring onnetor is 4 HP (4 TE) from neighboring unit or from edge of rk Power supply wiring onnetor is 25 HP (25 TE) from neighboring unit or from edge of rk Keyed sensor wiring onnetor is 16 HP (16 TE) from neighboring unit or from edge of rk STEP 3. Instlling the Model 3300/3500 in the rk 1. Align the Model 3300/3500 with the guide rils. 2. Slide the Model 3300/3500 into the rk. Mke sure the pins on the bk pnel mke ontt with the wiring onnetors. 3. Tighten the supplied ptive srews to seure the front pnel of the Model 3300/3500 to the guide rils. 6
STEP 4. Conneting input nd output wiring Connet input nd output wiring to the pproprite terminls on the input/output wiring onnetor, whih is the fr right onnetor. Refer to Tble 1 nd to the rd tht is inserted into the sleeve on the top pnel (shown in Figure 4). Use 24 to 16 AWG (0,25 to 1,5 mm 2 ) twisted-pir shielded wire. Ground the shields t single point only. Tble 1. Input/output wiring terminls Terminl number Designtion 2+ 2 Primry 4 20 ma output 4 + 4 Seondry 4 20 ma output 6 + 6 Frequeny input 8 + 8 Disrete input 1 10 + 10 Disrete input 2 12 + 12 Frequeny output 14 + 14 Disrete output 1 16 + 16 Disrete output 2 18 + 18 Disrete output 3 32 (B line) 32 (A line) RS-485 output Figure 4. Input/output wiring terminl rd STEP 5. Conneting the Model 3500 to the sensor To onnet the Model 3500 trnsmitter to Miro Motion sensor, follow the steps below. If you re instlling the Model 3300 pplitions peripherl, this step is not required. 7
1. Identify the omponents shown in Figure 5. Figure 5. Sensor ble to Model 3500 9-wire ble from sensor Model 3500 Keyed sensor wiring onnetor (see Figure 3, pge 6) blk (drin wires from ll wire sets) brown red green white blue gry ornge yellow violet yellow violet green blue brown 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 blk (drins) ornge white gry red 2. Prepre the ble ording to the instrutions in Miro Motion s 9-Wire Flowmeter Cble Preprtion nd Instlltion Guide. 3. Ensure tht the ble hs 360 shielding, ontinuous from the trnsmitter to the sensor s juntion box. Two methods n be used: Metlli onduit Shielded or rmored ble Refer to Miro Motion s 9-Wire Flowmeter Cble Preprtion nd Instlltion Guide for speifi instrutions. 4. At the sensor:. Clip the ble drin wires. b. Connet wiring inside the juntion box housing nd tighten the srews to hold the wires in ple. For informtion on your sensor s juntion box terminls, see the sensor instlltion mnul or Miro Motion s 9-Wire Flowmeter Cble Preprtion nd Instlltion Guide. 8
5. At the trnsmitter:. Connet the olor-oded wires to the pproprite terminls. To identify the terminls, refer to Figure 5, pge 8. No bre wires should remin exposed. b. If using shielded or rmored ble, onnet the ble brid to the rer stud, s desribed in Miro Motion s 9-Wire Flowmeter Cble Preprtion nd Instlltion Guide. STEP 6. Conneting power supply wiring CAUTION Improper wiring instlltion n use devie filure or mesurement error. To void devie filure or mesurement error, do not instll power supply wiring in the sme ble try or onduit s input/output wiring. Shut off power supply before instlling the pplitions pltform. Mke sure power supply voltge mthes voltge tht is indited on power supply wiring terminls. See Figure 6, pge 10. Referring to Figure 6, pge 10, onnet the Model 3300/3500 to power supply s follows: 1. Use 18 to 14 AWG (0,75 to 2,5 mm 2 ) wire. 2. Ground the power supply wiring: Connet the ground wire to the middle terminl. Connet the power supply ground diretly to erth ground. Keep ll ground leds s short s possible. Ensure tht ll ground wiring hs less thn 1 ohm impedne. 3. Connet wires to the upper nd lower terminls. A user-supplied swith my be instlled in the power supply line. For ompline with low-voltge diretive 73/23/EEC (Europen instlltions), swith in lose proximity to the rk is required. 9
Figure 6. Power supply wiring terminls Power supply wiring terminls Terminl designtions for DC power Terminl designtions for AC power 10
2003, Miro Motion, In. All rights reserved. P/N 3300995, Rev. C *3300995* Visit us on the Internet t www.miromotion.om Miro Motion In. USA Worldwide Hedqurters 7070 Winhester Cirle Boulder, Colordo 80301 T (303) 530-8400 (800) 522-6277 F (303) 530-8459 Miro Motion Europe Emerson Proess Mngement Wiltonstrt 30 3905 KW Veenendl The Netherlnds T +31 (0) 318 495 670 F +31 (0) 318 495 689 Miro Motion United Kingdom Emerson Proess Mngement Limited Horsfield Wy Bredbury Industril Estte Stokport SK6 2SU U.K. T 0800 966 180 F 0800 966 181 Miro Motion Asi Emerson Proess Mngement 1 Pndn Cresent Singpore 128461 Republi of Singpore T (65) 6777-8211 F (65) 6770-8003 Miro Motion Jpn Emerson Proess Mngement Shingw NF Bldg. 5F 1-2-5, Higshi Shingw Shingw-ku Tokyo 140-0002 Jpn T (81) 3 5769-6803 F (81) 3 5769-6843 TM Miro Motion