1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI BO026- BR Brakes - Pad Clicking Noise ST004- EG009- BO001-

Transcription

1 [object] Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle.. Technical Service Bulletins EG Emissions System - MIL ON/DTC's. Customer Interest 02 P0440/P0441/P0446 Set ST Front Suspension - Squeaking Noise 01 BO Seat Belts - Shoulder Anchor Tape Set BO Interior Trim - Sun Visor Vanity Mirror Broken/Damaged EG MIL ON - DTC P1133 Updated (Oxygen Sensor Circuit) BO Trunk - Water Leaks 00 BR Brakes - Pad Clicking Noise 00 ST P/S - Power Steering Rack Squeaking Noise BO009R A/C - Loose Center Vent 00 Adjustments NV Mirrors - Wind Noise from the Door Mirror BO A/C - Loose Center Vent Adjustment SU Suspension - Front Support Change Reduces Noise BO Sunroof - Inoperative 99 EG MIL ON - DTC P1133 Oxygen Sensor Circuit Response BO Windows - Door Glass Displaced 99 BO Doors - High Closing Effort/Weatherstrip Modification ST Steering - Rack Housing Bushing Noise BR002R Brakes - Front Pads 98 Groan/Grinding/Squeak/Vibration SU Suspension - Groans From Front Driving Over Bumps BO Seats - Modified Track Stops Chattering

2 [object] Page 2 of 2 BO EG Body - Fuel Door Not Releasing On First Attempt MIL ON - DTC P0441, P0446 (EVAP Control System) Copyright 2003 ALLDATA LLC Terms of Use

3 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Air-Fuel R of 2 04/29/2003 9:41 AM 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Powertrain Management. Computers and Control Systems.. Oxygen Sensor.... Testing and Inspection.... Component Inspection Air-Fuel Ratio (A/F) Sensor California Notes Air-Fuel Ratio (A/F) Sensor - California INSPECTION 1. INSPECT HEATER RESISTANCE OF A/F SENSOR (a) Disconnect the A/F sensor connector. (b) Using an ohmmeter, measure the resistance between terminals +B and HT. Resistance: ohms at 20 C (68 F) If the resistance is not as specified, replace the sensor.

4 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Air-Fuel R of 2 04/29/2003 9:41 AM (c) Torque: 44 N.m (450 kgf.cm, 32 ft.lbf) Reconnect the A/F sensor connector. 2. INSPECT OPERATION OF A/F SENSOR: See "Related Diagnostic Charts" in this section Copyright 2003 ALLDATA LLC Terms of Use

5 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - MIL ON - DTC P1133 Update Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest... MIL ON - DTC P1133 Updated (Oxygen Sensor Circuit) Notes MIL ON - DTC P1133 Updated (Oxygen Sensor Circuit) ENGINE EG April 20, 2001 Title: M.I.L. "ON" P1133 Models: '97 - '99 Camry and '99 Solara Introduction Under certain driving conditions, some S-FE California emission specification Camrys and S-FE California emission specification Solaras may exhibit a M.I.L. "ON" with DTC P1133 (Air Fuel Ratio Sensor Slow Response Malfunction). An improved Air Fuel Ratio (A/F) Sensor was developed to correct this condition (See TSB EG006-99). In some rare cases, P1133 may still set after the improved A/F sensor is installed. The Engine Control Module (ECM) logic has been modified to correct this condition. Applicable Vehicles ^ model year Camrys with 5S-FE California emission specification. ^ 1999 model year Solaras with 5S-FE California emission specification.

6 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - MIL ON - DTC P1133 Update... Page 2 of 3 Parts Information Warranty Information Applicable Warranty*: This repair is covered under the Toyota Federal Emissions Warranty. This warranty is in effect for 96 months or 80,000 miles, whichever occurs first, from the vehicle's in-service date. * Warranty application is limited to correction of a problem based upon a customer's specific complaint. Repair Procedure 1. Should a M.I.L. "ON" condition with P1133 be encountered, perform diagnostic procedures as described in the Repair Manual.

7 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - MIL ON - DTC P1133 Update... Page 3 of 3 2. If the problem source cannot be identified after checking all affected areas according to the Repair Manual, the cause may be an A/F Sensor or ECM logic malfunction. In this case, follow the procedure in the flowchart shown to determine which part needs to be replaced. Replace the ECM only if the A/F Sensor in the vehicle was produced after August 31, Copyright 2003 ALLDATA LLC Terms of Use

8 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - A/C - Loose Center Vent Adju Page 1 of 3 Top - Vehicle Technical Service Bulletins. Customer Interest A/C - Loose Center Vent.. Adjustment 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI. Notes A/C - Loose Center Vent Adjustment BULLETIN: BO GROUP: BODY DATE: March 10, 2000 TITLE: LOOSE CENTER HVAC VENT ADJUSTMENT MODELS: '98 - '99 CBU Camry Introduction: A repair procedure has been made available to remedy customer complaints regarding loose vertical adjustment of the center vents on CBU Camry. Applicable Vehicles: ^ 1998 through 1999 model year Japan built Camry. Production Change Information:

9 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - A/C - Loose Center Vent Adju... Page 2 of 3 Parts Information: Repair Procedure: 1. Remove the left vent barrel by gently prying using a wide flat tool with smooth edges. Be careful not to damage the vent assembly. 2. Install a washer (P/N ) on the shaft inside the vent duct. 3. Reinstall the vent barrel by carefully pushing it into position until it locks onto the shafts on the sides of the duct. Be sure the spacer and/or washer do not fall down into the vent duct. NOTE: The spacer (P/N ) can be ordered, if lost. 4. Confirm that the vent vertical adjustment is tighter and moves smoothly. 5. Repeat steps 1 through 5 for the right center vent.

10 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - A/C - Loose Center Vent Adju... Page 3 of 3 Warranty Information Applicable Warranty*: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. * Warranty application is limited to correction of a problem based upon a customer's specific complaint. Copyright 2003 ALLDATA LLC Terms of Use

11 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - A/C - Loose Center Vent Adju Page 1 of 3 Top - Vehicle Technical Service Bulletins. Customer Interest A/C - Loose Center Vent.. Adjustments 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI. Notes A/C - Loose Center Vent Adjustments BODY BO REVISED April 28, 2000 Title: LOOSE CENTER HVAC VENT ADJUSTMENT Model: '98 - '99 CBU Camry TSB Revision Notice: There is updated information in this bulletin. Introduction A repair procedure has been made available to remedy customer complaints regarding loose vertical adjustment of the center venison CBU Camry. Applicable Vehicles ^ 1998 through 1999 model year Japan built Camry. Production Change Information

12 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - A/C - Loose Center Vent Adju... Page 2 of 3 Parts Information Repair Procedure 1. Remove the left vent barrel by gently prying using a wide flat tool with smooth edges. Be careful not to damage the vent assembly. 2. Install a washer (P/N ) on the shaft inside the vent duct. 3. Reinstall the vent barrel by carefully pushing it into position until it locks onto the shafts on the sides of the duct. Be sure the spacer and/or washer do not fall down into the vent duct. NOTE: The spacer (P/N ) can be ordered, if lost. 4. Confirm that the vent vertical adjustment is tighter and moves smoothly. 5. Repeat steps 1 through 4 for the right center vent.

13 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - A/C - Loose Center Vent Adju... Page 3 of 3 WARRANTY INFORMATION Copyright 2003 ALLDATA LLC Terms of Use

14 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Brakes - Pad Clicking Noise Page 1 of 6 Top - Vehicle Technical Service Bulletins. Customer Interest.. Brakes - Pad Clicking Noise 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI. Notes Brakes - Pad Clicking Noise BRAKES BR October 20, 2000 Title: BRAKE PAD CLICKING NOISE Models: '90- '00 All Models Introduction A clicking type noise may be noticed when first applying the brakes after changing vehicle travel direction (Drive/Forward to Reverse, Reverse to Drive/Forward). This is a normal noise caused by the required brake pad-to-caliper clearances. When the direction of travel is changed, the brake pads may "shift" towards the new direction of travel. When the brake pad contacts the caliper, a clicking noise may be heard. To minimize this clicking noise, a disc brake caliper grease has been made available for use during brake service/maintenance operations. Under normal usage conditions this grease should be effective for a period of 6 months to 1 year. Applicable Vehicles ^ model year Toyota vehicles, all models. Parts Information

15 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Brakes - Pad Clicking Noise Page 2 of 6 Warranty Information Application Procedure There are two types of brake calipers: floating and fixed. Check the type of brake caliper installed on the vehicle by removing the wheel assembly. 1. Floating Type Brake Caliper A. Lift up or remove the brake caliper and suspend it securely. HINT :Do not disconnect the flexible hose from the brake caliper. B. If equipped with anti-squeal spring: Remove the anti-squeal springs. C. Remove the brake pads with anti-squeal shims. D. Remove the pad support plates from the torque plate. Clean any dust from the pad support plates, torque plates and brake pads.

16 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Brakes - Pad Clicking Noise Page 3 of 6 E. Apply a small amount of the disc brake caliper grease (1-2 mm thick) to both sides of the pad support plates. NOTE :Do NOT apply grease to the friction surfaces of the brake pads or the disc rotor. F. If the pad support plate is fixed to the torque plate with adhesive tape, perform the operation according to the flow chart. G. Apply a small amount of the disc brake caliper grease (1-2 mm thick) to the caliper as indicated in the illustration. H. Install the brake pads with the anti-squeal shims. I. If equipped with anti-squeal spring: Install the anti-squeal springs. J. Press the piston in firmly and install the brake caliper. NOTE : ^ Clean excess grease. from brake pad and caliper. ^ Do NOT apply grease to the friction surfaces of the brake pads or the disc rotor.

17 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Brakes - Pad Clicking Noise Page 4 of 6 K. Install the wheel assembly. 2. Fixed Type Brake Caliper There are two types of brake pads: ^ Type "A": Has a projection on the upper and lower side of the brake pad. (See illustration.) ^ Type "B": Has a flat upper and lower edge on the brake pad backing plate. Type "A" Brake Pad A. Remove the anti-squeal spring, clip and pad guide pin. B. Remove the brake pads with the anti-squeal shims. C. Clean any dust from the brake pads.

18 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Brakes - Pad Clicking Noise Page 5 of 6 D. Apply a small amount of the disc brake caliper grease (1-2 mm thick) to the areas indicated in the illustration. NOTE :Do NOT apply grease to the friction surfaces of the brake pads or the disc rotor. E. Install the brake pads with the anti-squeal shims. NOTE :Clean excess grease from the brake pads and caliper. F. Install the pad guide pin, clip and anti-squeal spring. G. Install the wheel assembly. Type "B" Brake Pad A. Remove the clip, pins and anti-rattle spring/pad retainer clip. B. Remove the brake pads with the anti-squeal shims. C. Clean any dust from the brake pads.

19 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Brakes - Pad Clicking Noise Page 6 of 6 D. Apply a small amount of the disc brake caliper grease (1-2 mm thick) to the areas indicated in the illustration. NOTE :Do NOT apply grease to the friction surfaces of the brake pads or the disc rotor. E. Install the brake pads with the anti-squeal shims. NOTE :Clean excess grease from the brake pads and caliper. F. Install the pad guide pin, clip and anti-squeal spring. G. Install the wheel assembly. Copyright 2003 ALLDATA LLC Terms of Use

20 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - California 1 of 2 04/29/2003 9:37 AM 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Powertrain Management. Computers and Control Systems... Oxygen Sensor... Description and Operation.... California Notes California To obtain a high purification rate for the CO, HC and NOx components of the exhaust gas, a three-way catalytic converter is used, but for the most efficient use of the three-way catalytic converter, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel ratio. The A/F sensor has the characteristic that provides output Voltage* approximately proportional to the existing air-fuel ratio. The A/F sensor output voltage* is used to provide feedback for the ECM to control the air-fuel ratio. By the A/F sensor output, the ECM can determine the deviation amount from the stoichiometric air-fuel ratio and control the proper injection time immediately. If the A/F sensor is malfunctioning, ECM is unable to perform accurate air-fuel ratio control. The A/F sensor is equipped with a heater which heats the zirconia element. The heater is controlled by the ECM. When the intake air volume is low (the temp. of the exhaust gas is low), current flows to the heater to heat the sensor for accurate oxygen concentration detection. *: The voltage value changes at the inside of the ECM only.

21 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - California 2 of 2 04/29/2003 9:37 AM Copyright 2003 ALLDATA LLC Terms of Use

22 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Child Restraint - Seat Top Stra Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. All Technical Service Bulletins Child Restraint - Seat Top Strap.. Installation. Notes Child Restraint - Seat Top Strap Installation BODY BO May 24, 2002 Title: CHILD RESTRAINT SEAT TOP STRAP BRACKET INSTALLATION Models: '83 - '00 All Models Introduction Child restraint seat top strap bracket installation procedures are provided to supplement the Owner's Manual. Beginning with 2001 models, the top strap brackets are factory installed.

23 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Child Restraint - Seat Top Stra... Page 2 of 2 NOTE: ^ The child restraint seat top strap assembly is not available as a service part. Contact the child restraint seat manufacturer for recommended top strap information, top strap to child restraint seat installation instructions, and top strap retailers. ^ The top strap brackets can only be installed on vehicles that have nuts welded in place by the factory. The locations of these nuts can be found in the Owner's Manual (for most 1983 and newer models.) Toyota does not recommend modifying vehicles that do not have nuts welded in place by the factory. Some Land Cruiser and RAV4 vehicles, prior to 2001 model year, may not have these nuts welded in by the factory. Applicable Vehicles ^ model year vehicles, all models. Parts Information Warranty Information Copyright 2003 ALLDATA LLC Terms of Use

24 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Installation Procedure/ReferenPage 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. All Technical Service Bulletins Child Restraint - Seat Top Strap.. Installation Installation Procedure/Reference... Information. Notes Installation Procedure/Reference Information Installation Procedure Child Restraint Seat Top Strap Bracket Installation Obtain the exact year and vehicle model Toyota Owner's Manual before beginning installation. 1. Confirm with the customer which seat location(s) they will be installing the child restraint seat. The Owner's Manual seat section provides an illustration showing available top strap bracket location(s). The illustration page in the Owner's Manual is shown in this bulletin. NOTE: Determine which kit parts are needed for each specific child seat location, by referring information in this bulletin.

25 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Installation Procedure/ReferenPage... 2 of Remove a 20mm diameter area of the carpet or trim material above the bracket mounting location. In some vehicles, a 20mm circle is already pre-cut into the interior trim material. Once the interior trim material is removed, the nuts welded in by the factory should be visible. 3. If a 5mm or 15mm spacer is specified, remove the red lock washer from the Bracket Sub-Assembly (P/N ) and remove the 10mm spacer. Assure the red lock washer is re-installed onto the bolt. If a 5mm spacer is needed, use the 15mm bolt from the CRS Kit (P/N ).

26 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Installation Procedure/ReferenPage... 3 of Install the bracket assembly, according to the directions in the Owner's Manual. Tighten the bolt to N-m, ( kgf-m, ft-lbf). ^ Assure the top strap is attached to the child seat, according to the child seat manufacturer's instructions. ^ Assure the child seat is installed in the vehicle according to the Toyota Owner's Manual (seat section). Owner's Manual Installation Reference Information

27 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Installation Procedure/ReferenPage... 4 of 10

28 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Installation Procedure/ReferenPage... 5 of 10

29 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Installation Procedure/ReferenPage... 6 of 10

30 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Installation Procedure/ReferenPage... 7 of 10

31 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Installation Procedure/ReferenPage... 8 of 10

32 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Installation Procedure/ReferenPage... 9 of 10

33 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Installation Procedure/Refe... Page 10 of 10 The illustrations shown contain a reference information chart. This chart contain. ^ Owner's Manual page(s) that provide the illustration showing available top strap bracket location(s). The information goes back to 1983 model year models and newer already had the bracket installed by the factory. Installation notes, such as bracket spacer sizes for each specific child seat location. Copyright 2003 ALLDATA LLC Terms of Use

34 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Doors - High Closing Effort/WPage 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest... Doors - High Closing Effort/Weatherstrip Modification Notes Doors - High Closing Effort/Weatherstrip Modification BODY BO January 15, 1999 Title: DOOR CLOSING EFFORT Models: '97 - '98 Camry Introduction To enhance the door closing effort on Camry vehicles, several production changes have been implemented on the door opening weatherstrips. Production Change Information ^ 1997 and 1998 Camrys starting with the following VINS: TMMK V-6 4T1BF22KXVU cyl 4T1BG22KXVU V-6 4T1BF22KXVU cyl 4T1BG22KXVU TMC V-6 JT2BF22KXW cyl JT2BG22KXW

35 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Doors - High Closing Effort/WPage... 2 of 2 Parts Information Repair Procedure Replace the Door Opening weatherstrip on the affected door. Warranty Information Applicable Warranty**: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. **Warranty application is limited to correction of a problem based upon a customer's complaint. Copyright 2003 ALLDATA LLC Terms of Use

36 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Drive Axles - Front Hub Nut RPage 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. All Technical Service Bulletins... Drive Axles - Front Hub Nut Replacement Notes Drive Axles - Front Hub Nut Replacement DRIVELINE/DIFFERENTIAL DL MARCH 6, 1998 TITLE: FRONT AXLE HUB NUT REPLACEMENT MODELS: '92 - '98 TERCEL, PASEO, COROLLA, CELICA, CAMRY '96 - '98 RAV4 Introduction Due to a change of the friction control treatment on the nut thread, both types of Front Axle Hub Nuts (silver and black) for Tercel, Paseo, Corolla, Celica, Camry and RAV4s are NOT reusable. NOTE: When replacing the Front Axle Hub Nut the new part must be the same color as the old part. When replacing a Silver nut -- use a NEW Silver nut and when replacing a Black nut -- use a NEW Black nut. Affected Vehicles

37 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Drive Axles - Front Hub Nut... RPage 2 of Tercel, Paseo, Corolla, Celica, Camry and RAV4s. Parts Information PART NUMBER PART NAME COLOR Nut, Axle Hub Silver Nut, Axle Hub Black Warranty Information Copyright 2003 ALLDATA LLC Terms of Use

38 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Emissions System - MIL ON/DPage 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest Emissions System - MIL ON/DTC's.. P0440/P0441/P0446 Set. Notes Emissions System - MIL ON/DTC's P0440/P0441/P0446 Set ENGINE EG Title: M.I.L. "ON" P0440, P0441 & P0446 Models: '98 - '99 Camry & Solara July 12, 2002 Introduction Under certain driving conditions, some model year Camry and Solara vehicles may exhibit a M.I.L. "ON" with DTCs P0440, P0441 and P0446 stored due to an inoperative Vapor Pressure Sensor 3 way Vacuum Switching Valve (VSV). An improved Vapor Pressure Sensor VSV has been developed to correct this condition. Applicable Vehicles ^ model year Camry & Solara vehicles. Parts Information

39 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Emissions System - MIL ON/DPage... 2 of 6 Required Tools & Material NOTE: Additional Diagnostic Tester Kits, Program Cards or SSTs may be ordered by calling OTC at Warranty Information Applicable Warranty *: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. * Warranty application is limited to correction of a problem based upon a customer's specific complaint. Inspection & Repair Procedure Test VSV Operation Using ACTIVE TEST on the Toyota Diagnostic Tester

40 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Emissions System - MIL ON/DPage... 3 of 6 1. Test operation of the Vapor Pressure Sensor VSV using the Toyota Diagnostic Tester in ACTIVE TEST (see screen flow in Figure 1). NOTE: Vapor Pressure Sensor VSV is listed as TANK BYPASS VSV on the Diagnostic Tester.

41 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Emissions System - MIL ON/DPage... 4 of 6 2. Locate Vapor Pressure Sensor VSV as shown in Figure 2 (or see SFI section of 1998 or 1999 Camry or Solara Repair Manual). 3. Using the Diagnostic Tester ACTIVE TEST switch the Vapor Pressure Sensor VSV (TANK BYPASS VSV) to ON using the arrow keys. 4. Does the Vapor Pressure Sensor VSV make a "click" noise when switched to ON? YES --> Go to "Test VSV for Vacuum Leaks". NO --> Go to Step Is the wiring harness connector properly connected to the Vapor Pressure Sensor VSV? YES --> Go to Step 6. NO --> Fix the connector, then return to Step Disconnect the wiring harness connector for the Vapor Pressure Sensor VSV. 7. Using a DVOM test at Pin 1 to a known good ground. (Red wire on Solara, black and yellow wire on Camry). Is battery voltage (B+) present at Pin 1 of the Vapor Pressure Sensor VSV connector when the TANK BYPASS VSV ACTIVE TEST is switched to ON?

42 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Emissions System - MIL ON/DPage... 5 of 6 YES --> Go to Step 8. NO --> Perform diagnosis of power circuit. 8. Using a DVOM test at Pin 2 to a known good ground. The ECM provides ground when the VSV is switched ON. (White and red wire on Solara, violet wire on Camry). Is there continuity to ground at Pin 2 of the Vapor Pressure Sensor VSV connector when the TANK BYPASS VSV ACTIVE TEST is switched to ON? YES --> Replace the Vapor Pressure Sensor VSV. NO --> Perform diagnosis of ground circuit. Test VSV for Vacuum Leaks 1. Locate the vacuum hose going from charcoal canister to Port F of the Vapor Pressure Sensor VSV (see Figure 3). 2. Remove vacuum hose from Port F of the Vapor Pressure Sensor VSV and connect a hand-held vacuum pump to Port F using a short length of vacuum hose. 3. Apply at least 10 mm Hg vacuum to the VSV. Is a vacuum held for at least 1 minute?

43 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Emissions System - MIL ON/DPage... 6 of 6 YES --> Go to Step 4. NO --> Replace the Vapor Pressure Sensor VSV. 4. Disconnect the hand-held vacuum pump and reconnect the vacuum hose from the canister to the Vapor Pressure Sensor VSV. 5. Locate the vacuum hose going from charcoal canister to Port P of the Vapor Pressure Sensor VSV (see Figure 4). 6. Remove the vacuum hose from Port P of the Vapor Pressure Sensor VSV and connect a hand-held vacuum pump to Port P using a short length of vacuum hose. 7. Apply at least 10 mm Hg vacuum to the VSV. Is a vacuum held for at least 1 minute? YES --> Go to Step 8. NO --> Replace the Vapor Pressure Sensor VSV. 8. Disconnect the hand-held vacuum pump and reconnect the vacuum hose from the canister to the Vapor Pressure Sensor VSV. 9. Continue diagnosis of the EVAP system. Reference TSB EG005-01, "EVAP System Operation Information." Copyright 2003 ALLDATA LLC Terms of Use

44 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Front Suspension - Squeaking Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest.. Front Suspension - Squeaking Noise. Notes Front Suspension - Squeaking Noise STEERING ST December 21, 2001 Title: STEERING RACK END NOISE Models: '97- '00 Camry (NAP) & '99 - '00 Solara TSB Update Notice :The information contained in this TSB updates ST dated June 16, Revised text is shown by asterisks. Introduction Some model year Camry (NAP) and Solara vehicles may experience a squeaking noise from the front suspension. To improve this condition, production parts have been changed. Applicable Vehicles ^ model year Camry (North American Produced) vehicles. ^ model year Solara vehicles. Production Change Information

45 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Front Suspension - Squeaking... Page 2 of 2 Parts Information * NOTE:* Current service parts may be GRAY or BLACK in color. Warranty Information Applicable Warranty*: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. * Warranty application is limited to correction of a problem based upon a customer's specific complaint. Copyright 2003 ALLDATA LLC Terms of Use

46 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Suspension - Groans From Fro Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest Suspension - Groans From Front.. Driving Over Bumps. Notes Suspension - Groans From Front Driving Over Bumps SUSPENSION SU August 7, 1998 Title: FRONT SUSPENSION GROAN NOISE Models: '97-'98 Camry (TMMK) & '95-"97 Avalon TSB Update Notice: The information contained in this TSB supersedes SUOO2-97 dated July 18, Introduction A groan or crunch noise may be heard from the front suspension when driving over speed bumps or dips in the roadway on some North American produced Camrys and Avalons. This noise can be confirmed by jouncing the front suspension up and down to pinpoint the noise. Production Change Information

47 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Suspension - Groans From Fro... Page 2 of 2 NOTE: Six ribs have been added to the top of the bumper which can be used to identify the new part (see illustration.) Parts Information Repair Procedures To repair a vehicle (built before the production change) with a groan or crunch noise from the front spring bumper, exchange the original part with a service part. Warranty Information This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. Warranty application is limited to correction of a problem based upon a customer's complaint. Copyright 2003 ALLDATA LLC Terms of Use

48 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Body - Fuel Door Not Releasi Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest... Body - Fuel Door Not Releasing On First Attempt Notes Body - Fuel Door Not Releasing On First Attempt BODY BO May 22, 1998 Title: FUEL DOOR OPERATION IMPROVEMENT Models: '97 - '98 Camry Introduction On some U.S. built 1997 and 1998 Camrys, the fuel filler door may not release on the first attempt. As a result, improvements have been made to the fuel filler door hinge spring and the fuel filler shield. Affected Vehicles and 1998 Camry vehicles within the following VIN ranges: Camry U.S. Plant # 1 4T1BG2 * K * VU to 4T1BG2 * K * WU

49 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Body - Fuel Door Not Releasi... Page 2 of 2 4T1BF2 * K * VU to 4T1BF2 * K * WU Camry U.S. Plant # 2 4T1BG2 * K * VU to 4T1BG2 * K * WU T1BF2 * K * CVU to 4T1BF2 * K * CWU Parts Information PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME Fuel Filler Door Hinge Sprin Same Fuel Filler Shield Repair Procedure Replace the fuel filler door hinge spring and fuel filler shield. Warranty Information Applicable Warranty: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's In-service date. * Warranty application is limited to correction of a problem based upon a customer's complaint. Copyright 2003 ALLDATA LLC Terms of Use

50 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Technical Service Bulletin Inf Page 1 of 2 Top - Vehicle Technical Service Bulletins. All Technical Service Bulletins Technical Service Bulletin.. Information 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI. Notes Technical Service Bulletin Information PRODUCT GENERAL INFORMATION PG MARCH 6, 1998 TITLE: 1998 TECHNICAL SERVICE BULLETIN INFORMATION MODELS: ALL MODELS Introduction Toyota Technical Service Bulletins (TSBs) continue to be one of the most current sources of technical information available. To ensure complete access to this reference source, use the following steps: All 1997 Technical Service Bulletins should be relocated to a temporary binder. - Place this bulletin along with all 1998 TSBs into the emptied TSB binder. - During the month of March, all dealers will receive bound books containing all TSBs issued in Upon receipt, discard all 1997 TSBs and refer only to the bound book for reference. - Additional copies of 1994 through 1998 TSBs are available to all Toyota dealerships through the Toyota Non Parts System (MDC NPM System) by using the Part Number designation:

51 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Technical Service Bulletin Inf... Page 2 of 2 Parts Information Copyright 2003 ALLDATA LLC Terms of Use

52 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Adjustments Page 1 of 1 Top - Vehicle Lighting and Horns. Headlamp.. Adjustments 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI. Notes Adjustments 1. ADJUSTMENT HEADLIGHT AIMING 2. ADJUSTMENT SPIRAL CABLE Copyright 2003 ALLDATA LLC Terms of Use

53 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Instrument Panel - Revised In Page 1 of 2 Top - Vehicle Technical Service Bulletins. All Technical Service Bulletins Instrument Panel - Revised.. Installation Procedure 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI. Notes Instrument Panel - Revised Installation Procedure BODY BO December 25, 1998 Title: CAMRY LOWER INSTRUMENT PANEL ASSEMBLY SERVICE TIP Models: '97-'98 Camry Introduction The instrument panel installation procedure has been revised in order to prevent rattles caused by broken clips. Please follow the procedure below when removing and reinstalling the No. 1 Lower Panel Assembly. Production Change Information ^ Camrys starting with the following VINs: 4T1BG22K * VUO T1BF22K * VU T1BG22K * VU T1BF22K * VU Repair Procedure Refer to 1998 Repair Manual page BO-75 (Step 5) for procedure and add the following steps:

54 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Instrument Panel - Revised In... Page 2 of 2 c. Remove the upper clips first. d. Remove lower bolt and screw second. NOTE: ^ To reinstall the panel, install upper clips first then install lower bolt & screw. ^ To prevent future rattle noises, take care not to break the clips during disassembly/reassembly. Warranty Information Copyright 2003 ALLDATA LLC Terms of Use

55 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Interior Trim - Center Console Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Body and Frame. Interior Trim.. Console... Technical Service Bulletins Interior Trim - Center Console.... Latch Improvements. Notes Interior Trim - Center Console Latch Improvements BODY BO March 26, 1999 Title: CAMRY CENTER CONSOLE LATCH IMPROVEMENTS Models: '97 - '99 Camry Introduction: The center console compartment door has been changed to improve the durability of the console box latch. Affected Vehicles: ^ Camrys produced before VIN: 4T1BG * * K * XU (L4) 4T1BF * * K * XU (V6) 4T1BG * * K * XU (L4) 4T1BF * * K * XU (V6) Parts Information: PREVIOUS PART # CURRENT PART # PART NAME 5891O-AAO1O-XX 5891O-AAO11-XX Console Box Assembly AAO1O-XX AAO11-XX Console Compartment Door Repair Procedure: On vehicles produced before the production change, replace the Rear Console Box with P/N AAO11-XX. Refer to Repair Manual for detailed repair procedures. NOTE: On vehicles produced after the production change, replace the console compartment door only.

56 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Interior Trim - Center Console... Page 2 of 2 These vehicles can be identified by a metal hinge on the console compartment door. Warranty Information Applicable Warranty*: This repair is covered Under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. * Warranty application is limited to correction of a problem based upon a customers specific complaint. Copyright 2003 ALLDATA LLC Terms of Use

57 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Interior Trim - Rear Console B Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. All Technical Service Bulletins Interior Trim - Rear Console Box.. Improvements. Notes Interior Trim - Rear Console Box Improvements BODY BO December 4, 1998 Title: CAMRY REAR CONSOLE BOX IMPROVEMENTS Models: '97-'98 Camry Introduction The rear console box has been changed to improve the durability of the console box hinge. Production Change Information ^ Camrys starting with the following VINs: 4T1BG * * K * VU (L4) 4T1BF * * K * VU (V6) 4T1BG * * K * VU (L4) 4T1BF * * K * VU (V6) Parts Information PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME AA011-XX AA011-XX Console Box Assembly Repair Procedure ^ On vehicles produced before the production change, replace the Rear Console Box with P/N AA011-XX. Refer to Repair Manual, page BO-72 for detailed repair procedures.

58 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Interior Trim - Rear Console... B Page 2 of 2 Warranty Information Applicable Warranty*: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's In-service date. * Warranty application is limited to correction of a problem based upon a customer's complaint. Copyright 2003 ALLDATA LLC Terms of Use

59 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Interior Trim - Sun Visor Van Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest... Interior Trim - Sun Visor Vanity Mirror Broken/Damaged Notes Interior Trim - Sun Visor Vanity Mirror Broken/Damaged BODY BO October 12, 2001 Title: SUNVISOR VANITY MIRROR IMPROVEMENT Models: '97 - '01 NAP Camry Introduction Production changes have been implemented on the model year NAP Camry vanity mirror assembly to improve strength and durability of the mirror cover hinge. Applicable Vehicles ^ model year NAP Camry vehicles.

60 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Interior Trim - Sun Visor Van... Page 2 of 2 Production Change Information Parts Information Repair procedure Replace damaged sunvisor with a service part. Warranty Information Applicable Warranty *: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. * Warranty application is limited to correction of a problem based upon a customer's specific complaint. Copyright 2003 ALLDATA LLC Terms of Use

61 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - MIL ON - DTC P1133 Oxyge Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest... MIL ON - DTC P1133 Oxygen Sensor Circuit Response Notes MIL ON - DTC P1133 Oxygen Sensor Circuit Response ENGINE EG Title: M.I.L. "ON" DTC P1133 Models: '97- '99 Camry and '99 Solara: 55-FE CA Spec. October 1, 1999 Introduction Under certain driving conditions, some 55-FE equipped Camry and 1999 Solara California emission specification vehicles may exhibit a M.I.L. "ON" DTC P1133. An improved Air Fuel Ratio Sensor has been developed to correct this condition. Applicable Vehicles Camry & 1999 Solara (55-FE) with California emission specification. Production Change Information Parts Information

62 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - MIL ON - DTC P1133 Oxyge... Page 2 of 2 PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME Sensor, Air Fuel Repair Procedure ^ Should a M.I.L. "ON" condition with DTC P1133 be encountered, perform diagnostic procedures as described in the Repair Manual. ^ It the problem source cannot be identified after checking all affected areas according to the Repair Manual, the cause may be an Air/Fuel Ratio Sensor malfunction. In this case, replace the Air/Fuel Ratio Sensor with the updated part. ^ If the Exhaust Manifold threads are damaged by removal of the sensor, they can be repaired by the proper use of a M18 x 1.5 tap. Warranty Information Applicable Warranty*: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. Coverage is extended to 36 months or 50,000 miles, whichever occurs first, in the states of California and Massachusetts due to state emissions warranty legislation. NOTE :Please enter the DTC in the condition/cause/remedy section when applying for warranty reimbursement. Copyright 2003 ALLDATA LLC Terms of Use

63 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - MIrrors - Vanity Mirror Impro Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. All Technical Service Bulletins... MIrrors - Vanity Mirror Improvement Notes MIrrors - Vanity Mirror Improvement BODY BO June 19, 1998 Title: VANITY MIRROR IMPROVEMENT Models: '96-'98 Avalon, '97-'98 Camry, '98 Sienna Introduction Production changes have been implemented on the 1998 Avalon, Camry and Sienna vanity mirror assembly to improve the strength and durability of the mirror cover hinge. Affected Vehicles ^ 1996 to 1998 Avalons with VINs before: 4T1BF18B * WU ^ 1997 to 1998 Camrys with VINs within the following VINs: ^ 4T1BG2 * K * VUOOOO74 to 4T1BG2 * K * WU (4 cyl.) ^ 4T1BG2 * K * VU to 4T1BG2 * K * WU (4 cyl.)

64 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - MIrrors - Vanity Mirror Impro... Page 2 of 2 ^ 4T1BF2 * K * VUOOOO72 to 4T1BF2 * K * WU (6 cyl.) ^ 4T1BF2 * K * VU to 4T1BF2 * K * WU (6 cyl.) ^ 1998 Siennas with VINs before: 4T3 * F1 * C * WU Parts Information MODEL CURRENT PART NUMBER PART NAME Avalon ACO10-XX Vanity Lamp Assembly ACO6O-XX Camry A0030-XX Vanity Lamp Assembly Sienna ACO3O-XX Vanity Lamp Assembly Repair Procedures Remove original vanity lamp assembly and install a new vanity lamp assembly. Warranty Information Applicable Warranty *: This repair is covered Under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. * Warranty application is limited to correction of a problem based upon a customer's complaint. Copyright 2003 ALLDATA LLC Terms of Use

65 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Mirrors - Wind Noise from the Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest Mirrors - Wind Noise from the Door.. Mirror. Notes Mirrors - Wind Noise from the Door Mirror BULLETIN NUMBER: NV DATE: March 31, 2000 TITLE: WIND NOISE FROM THE DOOR MIRROR MODELS: '97 - '99 Camry TSB UPDATE NOTICE: The information contained in this TSB updates BO dated December 3,1999. Revised text is red and underlined. INTRODUCTION Wind/road noise heard around the door mirrors of some Japan produced Camry vehicles may be caused by an improperly positioned mirror wire harness grommet and/or harness connector. APPLICABLE VEHICLES: 1997 through 1999 Camry vehicles. (Japan produced only) PRODUCTION CHANGE INFORMATION

66 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Mirrors - Wind Noise from the... Page 2 of 4 WARRANTY INFORMATION APPLICABLE WARRANTY*: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. Warranty application is limited to correction of a problem based upon a customer's specific complaint. REPAIR PROCEDURE: 1. Carefully pry off the door speaker cover and remove the nut using a 10 mm socket that secures the speaker to the door. 2. Look through the door mirror harness access hole and check the position of the wire harness grommet and wire harness connector - the harness connector should be inside the grommet and the grommet should be fully seated in the mirror housing.

67 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Mirrors - Wind Noise from the... Page 3 of 4 Examples of improperly installed assemblies are shown below: 3. To reposition the grommet and/or harness connector onto the mirror housing: ^ Remove the mirror housing (the remaining 2 nuts) from the door and carefully unclip the mirror from the housing. This will allow easier access and reinstallation of the grommet and/or harness connector. ^ Reposition the grommet so it is fully seated to the mirror housing. Assure the harness connector is inside the grommet. NOTE: Refer to the 1998 Camry Repair Manual pages BO-23 through BO-26.

68 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Mirrors - Wind Noise from the... Page 4 of 4 4. Reinstall the door mirror and speaker assembly: ^ Secure the mirror to the housing. ^ Properly align and reinstall the mirror assembly to the door. Tighten the upper and forward nuts. Torque: 5.5 N-m (56 Kgf-cm, 49 in-lb) ^ Reinstall the door speaker (one nut at the lower bracket) and speaker cover onto the door as shown in the illustration. Torque: 5.5 N-m (56 Kgf-cm. 49 in-lb) ^ Assure the power mirror adjustment and the door speaker functions properly. NOTE: Do NOT mount the UPPER speaker bracket behind the nut. Copyright 2003 ALLDATA LLC Terms of Use

69 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - P/S - Power Steering Rack Sq Page 1 of 2 Top - Vehicle Technical Service Bulletins. Customer Interest P/S - Power Steering Rack.. Squeaking Noise 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI. Notes P/S - Power Steering Rack Squeaking Noise STEERING ST June 16, 2000 Title: STEERING RACK END NOISE Models: '97 - '00 Camry (NAP) & '99 - '00 Solara Introduction Some model year Camry (NAP) and Solara vehicles may experience a squeaking noise from the front suspension. To improve this condition, production parts have been changed. Applicable Vehicles ^ model year Camry (North American Produced) ^ model year Solara Production Change Information

70 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - P/S - Power Steering Rack Sq... Page 2 of 2 Parts Information HINT: A quick reference in differentiating between the previous and new parts is that the previous Rack End Shaft is BLACK and the current part is GRAY. Warranty Information Applicable Warranty*: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. * Warranty application is limited to correction of a problem based upon a customer's specific complaint. Copyright 2003 ALLDATA LLC Terms of Use

71 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - P/S - Pressure Feed Tube/Line Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. All Technical Service Bulletins... P/S - Pressure Feed Tube/Line Changed Notes P/S - Pressure Feed Tube/Line Changed STEERING ST June 5, 1998 Title: Power Steering Pressure Feed Tube Models: '97-'98 Camry (TMMK) Introduction The power steering Pressure Feed Tube on both 4 cylinder and V6 North American produced Camrys has been changed. Production Change Information ^ Camrys (TMMK) starting with the following VINs: 5S-FE (L4) 1MZ-FE (V6) 4T1BG22K * WU T1BG22K * WU T1BF22K * WUO573O6 4T1BF22K * WU

72 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - P/S - Pressure Feed Tube/Line... Page 2 of 4 Parts Information Warranty Information * Both previous and current Pressure Feed Gaskets are interchangeable. Applicable Warranty *: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. Warranty application is limited to correction of a problem based upon a customer's complaint. Repair Procedure

73 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - P/S - Pressure Feed Tube/Line... Page 3 of 4 For repair of a leak at the Pressure Feed Tube and Gasket replace the Power Steering Pressure Feed Tube and Gasket. Refer to the Repair Manual for details. NOTE: Make sure the stopper of the Tube contacts the back side of the Pump Bracket as shown.

74 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - P/S - Pressure Feed Tube/Line... Page 4 of 4 NOTE: Before setting torque of the Union Bolt, make sure to position the index Bridge on the Gasket away from the Stopper on the banjo fitting. If the Index Bridge on the Gasket is deformed from its original condition, a new Gasket must be installed. Recommended repair torque for: Union Bolt - Torque: 52 N.m (525 kgf.cm, 38 ft.lbf) Oil Pressure Switch - Torque: 21 N.m (210 kgf.cm, 15 ft.lbf) Refer to the appropriate Camry Repair Manual, Steering Section (SR) for additional details. Copyright 2003 ALLDATA LLC Terms of Use

75 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Rear Hub Bearing O-Ring - Se Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. All Technical Service Bulletins Rear Hub Bearing O-Ring - Service.. Tip. Notes Rear Hub Bearing O-Ring - Service Tip SUSPENSION SU Title: REAR BEARING 0-RING SERVICE TIP Models: '97 - '01 Camry, '00 - '02 Avalon & '99 - '02 Solara March 1, 2002 Introduction When replacing the rear hub bearing assemblies on model year Camry, Avalon and Solara vehicles, replace the 0-ring. Applicable Vehicles ^ model year Camry vehicles. ^ model year Avalon vehicles produced before the VIN shown below. ^ model year Solara vehicles produced before the VIN shown below. Production Change Information

76 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Rear Hub Bearing O-Ring -... Se Page 2 of 3 Parts Information Warranty Information Repair Procedure REMOVAL 1. Remove Rear Wheel. Torque: 103 N.m (1,050 kgf.cm, 76 ft.lbf) 2. With Disc Brake: Remove Brake Caliper and Disc. A. Remove the brake caliper and disc. Torque: 47 N.m (475 kgf.cm, 34 ft.lbf) B. Support the brake caliper securely. 3. With Drum Brake: Remove Brake Drum. 4. Remove Rear Axle Hub. A. Remove the 4 bolts and rear axle hub.

77 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Rear Hub Bearing O-Ring -... Se Page 3 of 3 Torque: 80 N.m (820 kgf.cm, 59 ft.lbf) B. Remove the 0-ring. HINT: At the time of installation, coat the new 0-ring with MP grease. NOTE: Please ensure that the 0-ring is replaced with a new service part when installing the bearing assembly. C. With Drum Brake: Remove the bolt, and disconnect the flexible hose from the shock absorber. Torque: 29 N.m (300 kgf.cm, 22 ft.lbf) D. Support the backing plate securely. 5. With ABS: Remove ABS Speed Sensor Torque: 8.0 N.m (82 kgf.cm, 71 in.lbf) INSTALLATION Installation is in the reverse order of removal. Copyright 2003 ALLDATA LLC Terms of Use

78 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Recall 01V012000: Accelerato Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Recalls Recall 01V012000: Accelerator.. Cable Defect. Notes Recall 01V012000: Accelerator Cable Defect Vehicle Description: Passenger vehicles equipped with cruise control and V6 engines, and built at one of two lines at the Kentucky Plant. The accelerator cable housing could be deformed at the cruise control actuator-to-throttle body connection. The accelerator inner-cable could wear away and eventually break. This could allow the throttle to return to idle or remain in its most recent position regardless of accelerator pedal operation, increasing the risk of a crash. Dealers will replace the accelerator cable. Owner notification began February 23, Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Toyota at Also contact the National Highway Traffic Safety Administration's Auto Safety Hotline at DASH-2-DOT ( ). Copyright 2003 ALLDATA LLC Terms of Use

79 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Recall 99V307000: Steering WPage 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Recalls Recall 99V307000: Steering Wheel.. Set Nut Loose. Notes Recall 99V307000: Steering Wheel Set Nut Loose Vehicle Description: Passenger vehicles. The steering wheel set nut may not have been sufficiently tightened causing steering vibration and looseness. This can result in a loss of vehicle control. Dealers will tighten the steering wheel set nut. Owner notification began November 30, Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Toyota at or Lexus at Also contact the National Highway Traffic Safety Administration's Auto Safety Hotline at DASH-2-DOT ( ). Copyright 2003 ALLDATA LLC Terms of Use

80 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Seat Belts - Shoulder Anchor Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest Seat Belts - Shoulder Anchor Tape.. Set. Notes Seat Belts - Shoulder Anchor Tape Set BODY BO October 19, 2001 Title: SHOULDER BELT ANCHOR TAPE SET Models: All Applicable Avalon, Camry, Corolla, Previa, & Sienna Introduction To assist customers in preventing particle buildup and preserve the appearance of the shoulder belt anchor, the following procedure has been developed. Applicable Vehicles ^ model year Avalon vehicles. ^ model year Camry vehicles. ^ model year Corolla vehicles. ^ model year Previa vehicles. ^ model year Sienna*1 vehicles. *1 Except rear seat belt. Parts Information

81 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Seat Belts - Shoulder Anchor... Page 2 of 5 Warranty Information Applicable warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. * Warranty application is limited to correction of a problem based upon a customer's specific complaint. Installation Procedure 1. CLEAN SHOULDER BELT ANCHOR NOTE: ^ Do not install the tape when the vehicle temperature is below the freezing point. ^ Do not re-use removed fluorocarbon resin tape. A. Pull out the seat belt about 300 mm and attach a clip as shown in the illustration. HINT: Preventing the seat belt from retraction with a clip will make the following work easier.

82 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Seat Belts - Shoulder Anchor... Page 3 of 5 B. Put the Velcro tape (in the parts kit) through the hole of the shoulder belt anchor, brush-shaped side to the anchor. C. Pull both ends of the Velcro tape with your hand and shave off the dirt on the shoulder belt anchor by moving the Velcro tape several times as shown in the illustration. NOTE: Remove the dirt completely. Otherwise, the fluorocarbon resin tape may not adhere properly. 2. INSTALL FLUOROCARBON RESIN TAPE

83 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Seat Belts - Shoulder Anchor... Page 4 of 5 A. Place the fluorocarbon resin tape onto the seat belt as shown in the illustration. NOTE: Before installation of the fluorocarbon resin tape, it is necessary to pre-release the colored film about 5 mm for each side. (Not fully released.) B. By pulling up the seat belt, put the fluorocarbon resin tape through the hole of the shoulder belt anchor. Match the shoulder belt anchor to the center of the tape. C. Remove the upper side colored film from the fluorocarbon resin tape, and securely affix the tape to the outside of the shoulder belt anchor.

84 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Seat Belts - Shoulder Anchor... Page 5 of 5 D. Remove the lower side colored film from the fluorocarbon resin tape, and securely affix the tape to the outside of the shoulder belt anchor. NOTE : ^ Be sure to affix the fluorocarbon tape securely along all edges. ^ Pay attention not to make any wrinkles or slack in the fluorocarbon resin tape. E. Remove the clip. F. By pulling the seat belt up and down several times, as shown in the illustration, securely affix the fluorocarbon resin tape and confirm the smoothness of the belt movement. NOTE: Affix the fluorocarbon resin tape on the shoulder belt anchor to the other side following the same procedure. NOTE: If the seat belt requires cleaning to remove dirt, only use a neutral detergent or lukewarm water to clean. Use the seat belt after it is completely dried, to confirm proper operation. Copyright 2003 ALLDATA LLC Terms of Use

85 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Seats - Modified Track Stops Page 1 of 2 Top - Vehicle Technical Service Bulletins. Customer Interest Seats - Modified Track Stops.. Chattering 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI. Notes Seats - Modified Track Stops Chattering BODY BO June 5, 1998 Title: POWER FRONT SEAT CHATTERING Models: '97 - '98 Camry Introduction The recliner lead screw and lower rails have been changed to prevent seat cushion chattering on TMMK Camrys. Affected Vehicles ^ TMMK Camrys produced within the following VIN ranges: Parts Information PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME AA011 Same Front Power Seat Adjuste 72O10-AA011 Same Front Power Seat Adjuste

86 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Seats - Modified Track Stops... Page 2 of 2 Repair Procedure Replace the Seat Track Assembly on TMMK Camrys produced within the VIN ranges listed above. NOTE: The countermeasured parts can be Identified by a number greater than 0478 on the label attached to the front rail of the Front Power Seat Adjuster Assembly. Warranty Information Applicable Warranty *: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's In-service date. * Warranty application is limited to correction of a problem based upon a customer's complaint. Copyright 2003 ALLDATA LLC Terms of Use

87 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Steering - Gearbox Removal P Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. All Technical Service Bulletins... Steering - Gearbox Removal Precautions Notes Steering - Gearbox Removal Precautions STEERING ST May 22, 1998 Title: STEERING GEAR REMOVAL/REPLACEMENT Models: All Models equipped with SRS Airbag Introduction The following information is provided to supplement the Repair Manual procedure for removing/installing the steering gearbox or rack and pinion on vehicles equipped with a driver's side Supplemental Restraint System (SRS) Airbag. CAUTION :When the intermediate shaft is disconnected and the steering wheel is turned freely, the SRS spiral cable may be broken Therefore, as a precaution, make sure to pass the driver's seat belt through the steering wheel to prevent it from turning freely, as shown below. After working on SRS/Steering components, always check the operation of the SRS Warning Light. Refer to the appropriate repair manual If any diagnostic trouble codes are recorded. Affected Vehicles Tercel, Paseo, Corolla, MR2, Celica, Camry, Avalon, Supra, Previa, Sienna, RAV4, 4Runner, Tacoma, T-100 & Land Cruiser equipped with a driver's side SRS Airbag. Repair Procedure 1. Position the front wheels facing straight ahead. Figure # 1

88 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Steering - Gearbox Removal... P Page 2 of 2 2. Using the driver's seat belt, set the steering wheel so that it does not turn (see Fig. 1). Figure # 2 3. Paint match marks on the intermediate shaft and control valve shaft (see Fig. 2). 4. Remove the intermediate shaft retaining bolt and disconnect the intermediate shaft (see Fig. 2). Warranty Information Copyright 2003 ALLDATA LLC Terms of Use

89 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Steering - Rack Housing Bush Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest... Steering - Rack Housing Bushing Noise Notes Steering - Rack Housing Bushing Noise STEERING ST August 21, 1998 Title: STEERING RACK HOUSING BUSHING NOISE Models: '97 & '98 Camry Introduction The Steering Rack Bushing on Camry vehicles has been changed to reduce noise from the Steering Rack Housing Bracket No. 2. Production Change Information ^ Camrys starting with the following VINs:

90 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Steering - Rack Housing Bush... Page 2 of 3 JT2BG22K * V JT2BF22K * V T1BG22K * WU T1BG22K * WU T1BF22K * WU T1BF22K * WU Parts Information PREVIOUS PART NUMBER NEW PART NUMBER PART NAME Steering Rack Housing Bu Warranty Information Applicable Warranty*: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. Warranty application is limited to correction of a problem based upon a customer's complaint. Repair Procedure If the customer encounters noise in cold weather when turning at very low speed (2-3 m.p.h.), replace the Rack Housing Bushing with the updated part. NOTE: It is not necessary to remove the Steering Rack to replace the bushing. To remove the Rack Housing Bushing: 1. Remove the No. 2 Rack Housing Bolt.

91 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Steering - Rack Housing Bush... Page 3 of 3 2. Place matchmarks on the tie rod and rack end so that the toe will not be changed. Remove the Tie Rod End. 3. Remove the Rack Boot using a screwdriver to loosen the clamp. Be careful not to damage the boot. 4. Remove and replace the Bushing. Be sure to align the projection on the bushing with the hole in the bracket. Copyright 2003 ALLDATA LLC Terms of Use

92 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Sunroof - Inoperative Page 1 of 3 Top - Vehicle Technical Service Bulletins. Customer Interest.. Sunroof - Inoperative 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI. Notes Sunroof - Inoperative BODY BO December 17, 1999 Title SUNROOF OPERATION Models '97-'99 TMMK Camry Introduction Some TMMK Camry vehicles may experience an interruption in sunroof operation (not opening or closing). Changes have been made to the root drip channel guides to improve operation. The guides were modified to increase the clearance between the sun shade and opening flange by 2 mm. A radius was added to eliminate the sharp corners of the guides. Applicable Vehicles ^ TMMK Camry vehicles built before the production change. Production Change Information

93 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Sunroof - Inoperative Page 2 of 3 Parts Information Warranty Information Applicable Warranty*: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. Warranty application is limited to correction of a problem based upon a customer's specific complaint.

94 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Sunroof - Inoperative Page 3 of 3 Repair Procedure Remove the Roof Drip Channel Guides (left & right) and replace with the current parts. Copyright 2003 ALLDATA LLC Terms of Use

95 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Suspension - Front Support Ch Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest Suspension - Front Support Change.. Reduces Noise. Notes Suspension - Front Support Change Reduces Noise Bulletin Number: SU Group: SUSPENSION Date: January21, 2000 Title: FRONT SUSPENSION SUPPORT NOISE Models: '97 - '99 Avalon & '97 - '00 Camry TSB Update Notice: The information contained in this TSB updates SUOO2-99 dated September 3, Introduction: To eliminate a noise occurrence from the front suspension on washboard type road surfaces, the suspension support has been changed. Applicable Vehicles: Model Year Avalon and Camry vehicles.

96 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Suspension - Front Support Ch... Page 2 of 3 Production Change Information: The rubber bushing shape of the suspension support has been changed. Parts Information Warranty Information Applicable Warranty*: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. * Warranty application is limited to correction of a problem based upon a customer's specific complaint.

97 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Suspension - Front Support Ch... Page 3 of 3 Copyright 2003 ALLDATA LLC Terms of Use

98 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Trunk - Water Leaks Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins.. Customer Interest.. Trunk - Water Leaks Notes Trunk - Water Leaks BODY BO November 3, 2000 Title: LEAKS INTO TRUNK Models: '97 - '01 Camry (U.S.), '98 - '01 Sienna, '99 - '01 Solara & '01 Avalon Introduction A field fix is available for incidents of moisture and odors permeating into the vehicle. The Quarter Panel Air Duct flaps may have become loose or missing. Replacing the Quarter Panel Air Duct will remedy the condition. Applicable Vehicles ^ model year Camry (U.S. produced) ^ model year Sienna ^ model year Solara ^ 2001 model year Avalon

99 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Trunk - Water Leaks Page 2 of 2 Production Change Information Parts Information Repair Procedure Replace the Quarter Panel Air Duct. Warranty Information Applicable Warranty*: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. * Warranty application is limited to correction of a problem based upon a customer's specific complaint. Copyright 2003 ALLDATA LLC Terms of Use

100 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Valve Cover Oil Baffle - Dam Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. All Technical Service Bulletins Valve Cover Oil Baffle - Damage.. Prevention. Notes Valve Cover Oil Baffle - Damage Prevention ENGINE EG Title: GENERAL MAINTENANCE TIP Models: All '93 - '03 Models March 22, 2002 Introduction To help prevent unnecessary complications during the oil fill process, no undue load should be placed on the oil baffle attached to the inside of the valve cover (see illustration). This baffle is designed to deflect oil and should not be used to support the weight of heavy oil fill devices. These devices can place stress on the baffle, and bend or break it during the oil fill process.

101 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Valve Cover Oil Baffle - Dam... Page 2 of 2 Applicable Vehicles ^ All model year Toyota vehicles. Oil Filling Procedure Please take measures to ensure that the baffle is not damaged during the oil fill process. If it does become damaged, repair it before any collateral damage occurs. Warranty Information Copyright 2003 ALLDATA LLC Terms of Use

102 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Windows - Door Glass Displa Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest.. Windows - Door Glass Displaced. Notes Windows - Door Glass Displaced BODY BO Title: DOOR GLASS DISPLACEMENT FIELD FIX Models: '98 - '99 TMMK Camry September 3, 1999 Introduction On some 1998 and 1999 Camry Vehicles, the door glass may be displaced from the front door glass run if the door is closed forcefully with the windows partially down. A field fix has been developed in order to remedy this condition. Applicable Vehicles ^ TMMK Camrys built before 4T1BG * * K * XU T1BF * * K * XU T1BG * * K * XU T1BF * * K * XU Parts Information PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME N/A AAO10 Self-Adhesive Stopper Warranty Information

103 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Windows - Door Glass Displa... Page 2 of 3 Applicable Warranty*: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. * Warranty application is limited to correction of a problem based upon a customer's specific complaint Repair Procedure Refer to 1998 Camry Repair Manual (Vol. 2) Pages BO Remove the front door trim to gain access to the window components. 2. Inspect the front and rear lower frames and the door glass run for damage as a result of the glass being displaced. ^ In cases of slight deformation of window frames, reform as necessary. If significantly deformed or damaged, replace the frame. ^ Replace the window run if cut, torn, mutilated, etc. 3. Replace any damaged parts. 4. Remove front lower frame from the door and attach the self-adhesive rubber stopper (P/N AAO1O) 120 mm from the top of the frame as shown above. NOTE :To insure proper adhesion of the self-adhesive rubber stopper, the surface of the frame must be cleaned to remove any foreign material.

104 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Windows - Door Glass Displa... Page 3 of 3 5. Reinstall the front lower frame, door glass run, and door trim. Copyright 2003 ALLDATA LLC Terms of Use

105 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Windshield Wiper Blade - Ma Page 1 of 2 Top - Vehicle Technical Service Bulletins. All Technical Service Bulletins Windshield Wiper Blade -.. Maintenance and Cleaning 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI. Notes Windshield Wiper Blade - Maintenance and Cleaning BODY BO Title: WINDSHIELD WIPER BLADE MAINTENANCE AND CLEANING Models: All Models December 7, 2001 Introduction The following procedures are recommended to maintain windshield wiper blade performance. Applicable Vehicles ^ All models. Warranty Information Maintenance, Cleaning and Use Recommendations for Windshield Wiper Maintenance, Cleaning and Use: 1. Scheduled Maintenance ^ Check wiper rubber blades every 4-6 months or 7,500 miles for wear, cracking and contamination. ^ Clean glass and rubber wiper blades if blades are not clearing glass adequately. If this does not correct the problem, then replace the rubber elements.

106 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Windshield Wiper Blade - Ma... Page 2 of 2 2. Cleaning Procedure ^ Wiper Rubber: Bugs, dirt, sap and road grime on blades will cause streaking. ^ Clean wiper rubber of road and environmental debris using cloth or paper towel soaked with windshield washer fluid or mild detergent. ^8DO NOT USE fuel, kerosene, or petroleum based products to clean rubber wiper blades. ^ Windshield: Bugs, road grime, sap and car wash wax treatments decrease wiper performance. ^ Rinse windshield with water and apply non-abrasive cleaner, such as Bon-Ami ( with a sponge. NOTE: Make sure to use plenty of water with all powder based cleaners so the glass is not scratched. 3. Contributors to Poor Performance/Decreased Rubber Blade Life (require rubber replacement) ^ Dusty areas cause the rubber edge to wear quickly. ^ Sand and salt used for road conditioning during winter causes the edge to wear quickly, so areas with significant snowfall require more frequent wiper replacement. ^ Heat and time cause the rubber to become excessively "permanent set," so the rubber does not turn over, resulting in streaking and/or unwiped areas on the glass. ^ Rubber is easily cut or torn while using ice scrapers on the glass. ^ Rubber can be torn when pulling blades off a frozen windshield. ^ Using wipers instead of an ice scraper to remove frost and ice from the windshield during a car warm up can dull, nick, or tear the rubber. ^ Banging wiper on the glass to remove ice & snow can cause the blade to bend and rubber to come out of the blade providing the potential to scratch the glass. ^ Ice forms in wiper blade pin joints, which causes streaking and unwiped areas. To remove ice from pin joints, compress the blade and rubber with your hand to loosen the frozen joints. To prevent this condition, use winter blades with a rubber cover. Copyright 2003 ALLDATA LLC Terms of Use

107 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Brakes - Front Pads Groan/Gr Page 1 of Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI Top - Vehicle Technical Service Bulletins. Customer Interest Brakes - Front Pads.. Groan/Grinding/Squeak/Vibration. Notes Brakes - Front Pads Groan/Grinding/Squeak/Vibration BRAKES BR002R-98 August 7, 1998 Title: FRONT BRAKE NOISE Models: '97 - '98 Camry L4 Introduction New Front Brake Kits are available to reduce front brake groan noise and grinding noise, or squeak or vibration. Affected Vehicles ^ All 1997 and cylinder Camrys. Parts Information

108 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI - Brakes - Front Pads Groan/Gr... Page 2 of 3 For models with ABS - (Approximately 90% of L4 Camry sales were equipped with ABS) Warranty Information For models with ABS - For models without ABS -