Product Catalogue A1 Roadlines Pty Ltd

Transcription

1 Product Catalogue A1 Roadlines Pty Ltd

2 The specifications in this catalogue are correct at the time of publication but are subject to change at the discretion of the manufacturer and are indicative of the makes and models shown. Other makes and models may be available with differing specifications. 2

3 INDEX Portable Traffic Signal Systems 4-7 LED Flashing Arrow Signs Type A & B 8 LED Solar Flashing Arrow Sign Trailer Type C 9 Truck Mounted Attenuator (TMA) Trailer Mounted Attenuator (TA) 12 GL3000 Guidance Lasers 13 GMax3400 & GMax II 3900 Pedestrian Line Marker 14 GMax II 5900 & GMax II 7900 Pedestrian Line Marker 15 Graco LineLazer IV & LineDriver Graco RoadLazer RoadPak Line Striper Graco ThermoLazer & ThermoLazer ProMelt Graco GrindLazer 24 Line Remover 25 Line Marking Products & Stencils 26 Graco FieldLazer 27 3

4 Portable Traffic Signal Systems Master and Slave Communications between the MASTER and SLAVE is by radio or cable link. The Portable Traffic Signals have an in-built fail safe system such that they will automatically revert to flashing yellow operation in the event that a hazardous, incompatible or other fault condition occurs. A1 Roadlines, the leaders in Traffic Control Equipment, offers you the most advanced, most reliable and cost-effective Portable System on the market. Our CS-200 Model Solar Portable Traffic Signal Systems comply with Australian Standard AS Portable Traffic Signal Systems and various State Road Authority Specifications. Portable Traffic Signals are used where temporary control of vehicular traffic is required, such as at road or bridge works. It provides two main forms of control via shuttle control and plant-crossing control. The equipment is comprised of two electronic controllers known as MASTER and SLAVE mounted in a trailer unit that is capable of being split with each unit being positioned separately on the work site. The dual-trailer system allows the trailers to be connected together so that it can be towed as one individual unit. This capability allows the system to be towed to the job site using one vehicle. The Portable Traffic Signals are capable of operating under manual or automatic control and each separate unit is fully self-contained and powered by battery with a solar charging system. The fully lockable steel enclosure protects the controller and batteries from the elements and vandalism. Modes Of Operation Manual Fixed Time Flashing Yellow Vehicle Actuated using Radar Vehicle Detectors Radio Remote Control 4

5 Operational Features One Way or Two Way Operation TRH-3 Radio Linked Hand Held Controller (Operates up to 1km from Master). OR Cable Linked Handheld Controller (Operates up to 25m from Master) Time displayed in seconds All times easily entered and stored automatically in computer memory Battery Charger Indicator Fault description displayed on Liquid Crystal Display Auxiliary Lantern Drives provided for intersection control Maintenance Facilities Inbuilt fault log Lanterns can be turned off for set-up and maintenance Readily available components used in manufacture Fully Australian designed and manufactured providing easy access to support and spare parts Lanterns All Portable Traffic Signal Systems are fitted with Australian Standard AS Traffic Signal Lanterns 200mm, 3 aspect LED Lanterns. Radio-Link Communications The A1 Roadlines range of Portable Traffic Signal Systems employs sophisticated radio-link communications between the two trailers. This ensures constant, reliable communications in all operating modes. Optional Extras TRH-3 Radio Remote Control The water-resistant remote control lets you operate the system up to 1km (LOS) from the master control and features an LCD display. The unit operates up to 8 hours on an internal rechargeable battery. AGD202 Radar Vehicle Detector The AGD202 Radar Vehicle Detector is designed to be mounted near the red aspect of the traffic signal lantern pointing towards the oncoming traffic. The detector has a single zone of detection stretching from the radar to typically 60m along the carriageway. The detection zone is such that only vehicles approaching the detector are detected and vehicles travelling away from the detector are ignored. 5

6 Portable Traffic Signal Systems Power Supply Solar System Silent, environmentally safe, highefficiency solar power delivers peak current year round, even under extreme heat or overcast conditions. Fitted with two (2) 60W Solar Modules per unit, 10AMP solar power regulator and six (6) 6V 210Ah Batteries. Battery Charger A 240V 45AMP on board Battery Charger with 15AMP External Power Inlet is also available as an optional extra. SPECIFICATIONS TRAILER Solar Trailer Solar Trailer & Sign Frame Length (Overall) 3500mm 3800mm Width (Overall) 1630mm Height (Travel Position) 1670mm Height (Operating Position) 3000mm Combined Gross Weight 935kg 1015kg Finish Polyester Powder Coat Wheels, Tyres 155/70R13, Ford Stud Pattern Coupling 50mm Quick Release Ring Coupling Optional Extra Tail Lights Dual Voltage LED LANTERN Lantern (AS ) 12 V 200mm, 3 Aspect LED Max Lamp Drive Current >2.0 amp Visibility Distance 100m CONTROLLERS Model CS-200 Min. & Max. Times Pre-set as per State Specifications Distance Apart 1000m Radio Link 400m Cable Link POWER Primary Source Six (6) x 6V 210Ah Batteries Solar Controller 10AMP Back-Up Supply Two (2) x 60W Solar Panels 6

7 Portable Traffic Signal Systems SPECIFICATIONS Battery Version Solar Version Length (Overall) 1200mm 1200mm Width (Operating Position) 810mm 810mm Height (Travel Position) 1300mm 1300mm Height (Operating Position) 2550mm 2550mm Weight 137kg 159kg Finish Polyester Powder Coat Wheels, Tyres 4.10 x 3.50 x 6 4ply LANTERN Lantern (AS ) 12V 200mm, 3 Aspect LED Max Lamp Drive Current >2.00 amp Visibility Distance 100m CONTROLLERS Model CS-200 Min. & Max. Times Pre-set as per State Specifications Distance Apart 1000m Radio Link 400m Cable Link POWER Primary Source One (1) x 12V 210Ah Battery One (1) x 6V 210Ah Batteries Solar Controller N/A 10AMP Back-Up Supply N/A One (1) x 40W Solar Panels Battery Charger 240V 25AMP Charger with 15AMP External Inlet n Battery Version PURPOSE BUILT TRAILER & WHEELBARROWS COMBINED SPECIFICATIONS Length (Overall) 3170mm Width (Overall) 1390mm Height (Travel Position) 1740mm Weight (Battery Version) 450kg Weight (Solar Version) 494kg Tyres Alloy Wheel Brakes None Finish Galvanised Coupling 50mm Quick Release Ring Coupling Optional Extra Tail Lights Dual Voltage LED Wheelbarrow System Our Wheelbarrow Portable Traffic Signal System complies with Australian Standard AS Portable Traffic Signal Systems and various State Road Authority Specifications. The MASTER and SLAVE units are mounted in a small steel housing mounted on two pneumatic wheels that are capable of being wheeled around the work site. n A purpose built trailer is available for easy transportation of the Wheelbarrow System. n Solar Version Available in two options Battery Only Version with 25AMP Battery Charger or Solar Version with 25AMP Battery Charger. 7

8 LED Flashing Arrow Signs - Type A & B Australian Standards The Type A & B LED Flashing Arrow Signs meet AS Illuminated Flashing Arrows Signs and and Roads and Maritime Services Flashing Arrow Sign Specification FAS/5. Type A The Type A or Type B LED Flashing Arrow Signs are designed to be vehicle mounted and give advance warning of a short-term road closure and are available in single or double sided and operates from 12V to 24V systems without voltage converters. The arrow controller is lightweight and available for single or doublesided arrow signs. Type B Features Easy to use one touch controller, with real time display Arrow can be changed at the push of a button In built LED diagnostics Automatic dimming Heavy duty military specification wiring connectors Optional power lift control SPECIFICATIONS SINGLE SIDED Model Type A Type B Size 1260mm x 650mm 1500mm x 770mm No. Lamps Face No. Lamps Rear Nil Nil Flash Rate 35 cycles per minute 35 cycles per minute For Use On Cars, Vans, Utilities or Small Plant items Trucks or Larger Plant items Visibility Distance 0-500m 0-860m Modes Of Operation Arrow Right Arrow Left Double-Headed Arrow Non-Directional Warning 8

9 LED Flashing Arrow Sign Type C The Type C LED Flashing Arrow Sign meets AS Illuminated Flashing Arrow Signs and Roads & Maritime Services Flashing Arrow Sign Specification FAS/5. Type C LED Flashing Arrow Sign Trailer is a self-contained item of plant supplied on its own trailer with back-up battery supply powered by two (2) 80W solar panels positioned flat on top of the arrow sign to attain the optimum solar energy regardless of trailer direction. Used in conjunction with other signs and devices it provides advanced warning and directional information to assist in diverting and controlling traffic around construction or maintenance activities. A lockable steel enclosure protects the controller and batteries from the elements and vandalism. Modes Of Operation Arrow Right Arrow Left Double-Headed Arrow Non-Directional Warning The Type C LED Flashing Arrow Sign is also available for Truck or Trailer Mounted Attenuators. SPECIFICATIONS TRAILER Fixed Mast Tilt Adjusting Mast Length (Overall) 3150mm Width (Travel Position) 1730mm Width (Operating Position) 2440mm Height (Travel Position) 2730mm Height (Operating Position) 3500mm Combined Gross Weight 620kg 720kg Finish Polyester Powder Coat Wheels, Tyres 175/75 R14, HT Stud Pattern Coupling 50mm Quick Release Ring Coupling Optional Extra Tail Lights Dual Voltage LED ARROW SIGN Size 2440mm x 1220mm No. Lamps Face 15 No. Lamps Rear 2 Flash Rate 35 cycles per minute Visibility Distance 0-860m For Use On Trailer or TMA POWER (TRAILER) Primary Source Six (6) x 6V 210Ah Batteries Solar Controller 20AMP Back-Up Supply Two (2) x 80W Solar Panels 9

10 Scorpion Truck Mounted Attenuator (TMA) The Scorpion Model C TL-3 Truck Mounted Attenuator (TMA) is mounted to a shadow vehicle for purposes of protecting the work crew in front of the shadow vehicle and protecting the motorist that might drive into the lane closed off by the shadow vehicle. The Scorpion Model C TL-3 TMA is designed to conveniently fold up and over the flat bed or tipper truck during transport and storage. The compact design and balanced weight distribution makes it ideal for high-speed travel. Its low profile and open tubular design are beneficial in minimising wind resistance and drag, enabling you to drive at freeway speeds safely, as well as increasing rear visibility. The Scorpion TL-3 TMA consists of strut and cartridge sections that are linked together on a support frame. The curved side rails are made from corrosion resistant aluminium tubes, which offer full width impact protection along the entire length of the TMA. The side rails were designed to re-direct errant vehicles away from the rear of the truck (coffin corner). The aluminium boxes are filled with a moisture proof, aluminium honeycomb material. The boxes, together with the curved side rails, absorb the energy from an impacting vehicle. The aluminium boxes are painted with a bright yellow powdercoated finish, for lasting durability. Upon impact, the Scorpion TMA crushes in progressive stages. When hit by a lighter vehicle weighing approximately 820kg, travelling at speeds up to 100 km/h, the impact will crush the cartridge section of the 10

11 SPECIFICATIONS Weight 900kg Length (from back of vehicle) - Travel/Storage 974mm - Deployed 4210mm Width 2450mm Height (from ground) - Travel/Storage 3650mm - Deployed (Ground Clearance) 300mm Custom-Built Trucks A1 Roadlines also specialises in the manufacture of TMA trucks and are tailor made to meet state specifications for TMAs and customer requirements. Scorpion. When hit by a heavier vehicle, such as a truck or 4WD weighing approximately 2000kg, travelling at speeds up to 100km/h, both the strut and cartridge sections will crush, absorbing the energy from the impact. Incidental damage sometimes occurs during backing-up or turning corners. With Scorpion s modular design and construction, only the portions of the TMA that are damaged need to be replaced. The Scorpion TL-3 TMA has been tested and passed all optional and mandatory requirements of NCHRP- 350 Test Level 3 (TL-3) and can be used in work zones up to 100 km/h. Our commitment to quality and attention to detail is evident in the TMA trucks we have built. TMA Accessories available to meet state specifications Automatic Impact Braking System (AIB) 4 Point Harness Seat Belt and Mounting LED Warning Lamps Beacons Rearview Camera System Type C LED Flashing Arrow Sign In-Cabin Control Panel UHF Radio Permanent Mounted Class 1 Multi-Message Sign Variable Message Sign 11

12 Scorpion Trailer Attenuator Trailer Attenuator The Scorpion Trailer Attenuator from TrafFix Devices Inc. has also been tested and passed all optional and mandatory requirements of NCHRP 350, Test Level 3 (TL-3) and can be used in work zones up to 100 km/h. Features: Only Trailer Attenuator tested and approved when attached to a 4.5 tonne host vehicle. Single point attachment to standard 20,000kg (minimum) rated pintle hook is quick and easy. The unique curved design gives full width protection to the back of the host vehicle and protects the coffin corners of the truck. Rear axle placement improves trailer stability and prevents the tail from bottoming out on driveways or uneven surfaces. Available in a shorter (3.8m) lower speed TL-2 (70 km/h) model, which is ideal for congested city streets. Optional Type C LED Flashing Arrow Sign can easily be attached to the Scorpion Trailer Attenuator. Telescoping Anti-Rotational System (TARS ) minimises Scorpion Trailer rotation during angled impacts and prevents trailer separation from host vehicle. The Scorpion s proven modular design crushes in progressive stages allowing quick and economical replacement of damaged parts. SPECIFICATIONS TL-2 TL-3 Weight 760kg 1060kg Length 3800mm 5300mm Width 2400mm 2400mm Height 900mm 900mm 12

13 GL3000 Guidance Lasers The GL3000 Series Lasers use an ultra high visibility green Laser to establish visual line control. Depending on the model, the operator adjusts the laser spot to the desired reference point on the road surface using a remote control panel located in the cab of the vehicle or manually at the laser. The laser spot is impacted directly on the road surface about 10 to 30 feet ahead, showing the operator exactly where the vehicle is relative to on line. The Laser spot is on the road ahead of the operator so that the reference is in the driving field of view instead of a TV screen or boom pointer. GL3000P The GL3000P Guidance Laser uses an ultra high visibility green laser to establish visual line control for the vehicle driver. Used for highway paint striping, asphalt distributors, road wideners, pavement profilers, or virtually any application requiring vehicle line control. GL3000P model is for truck mounting. GL3000PM The GL3000PM Guidance Laser uses an ultra high visibility green laser to establish visual line control. Used for highway paint striping, asphalt pavers, road wideners, pavement profilers, or virtually any application requiring vehicle line control. The GL3000PM is also particularly effective for gun carriage alignment on paint striping trucks. n GL300PM Gun carriage guidance n GL300PM gun carriage guidance and GL3000P truck guidance from bird s eye view n GL300P Truck guidance 13

14 A1 GMax 3400 & GMax II 3900 Line Marker A1 Model GMax 3400 The A1 Model GMax 3400 is the introductory model of our range. n GMax 3400 Ideal for marking factories, schools, shopping centres, sports fields and light commercial duty. The Chromex Rod means that even the baby of the range has the strength to be used day in day out while still maintaining low weight and excellent output (up to 2.8 litres per minute, max tip size.027) A1 Model GMax II 3900 The A1 Model GMax II 3900 is the perfect contractor choice for professional line marking contractors. A lightweight machine with all the output you ll need (up to 4.7 litres per minute, max tip size.036). The GMax II 3900 also has the SmartControl which enables full control over the pump and its functions via its easy to read LCD readout. The GMax II 3900 also has Graco s ProConnect system which allows the pump to be removed without tools for easy repair. No other pump has this function. The machine comes complete with 15 metres of hose and one spray gun which can be fixed for line work or easily disconnected for hand/stencil work. A second gun is offered as an optional extra. n ProConnect System Open Closed n GMax II 3900 SPECIFICATIONS OPERATOR SPECS GMax 3400 GMax II 3900 Maximum Tip Size 1 gun to gun to guns to Maximum Delivery Rating 2.8 litres/min 4.7 litres/min Maximum Working Pressure 3300 psi (227 bar) 3300 psi (227 bar) Hose Length 15m 15m Engine 4.0 HP Honda Pull Start 4.0 HP Honda Pull Start Pro Connect N/A ü Typical Applications Small jobs, schools, sports fields, factories etc. Small - Medium Line marking Contractor OPTIONAL EXTRAS Bead Hopper & Dispenser ü ü QuickSelect Gun Selector* ü ü *QuickSelect Gun Selector - for simultaneous Paint & Beads 14

15 A1 GMax II 5900 & GMax II 7900 Line Marker Both the GMax II 5900 & GMax II 7900 are for the serious contractor who needs a heavy duty line marker with no compromises. n GMax II 7900 Now you can have the best of both worlds. A heavy duty machine fitted with the latest technology but easier to maintain than any machine you ve used before. A1 Model GMax II 5900 The GMax II 5900 is fitted with one hand gun and one striping gun. The new GMAX II 5900 can now handle a.043 tip with a whopping 6 litres per minute (free flow) from its new Chromex Piston Rod. n GMax II 5900 A1 Model GMax II 7900 The GMax II 7900 now offers the most output of any piston pump pedestrian line marker on the market. It s 8.3 litres per minute (free flow) means you can spray up to 3 guns at once! Great for airport runways. Both pumps offer the Graco ProConnect displacement pump which means you need NO tools to completely remove the pump. A fantastic innovation, which means less downtime when replacing the packings. When line marking is your livelihood - don t compromise. Either one of these heavy duty machines will give you years of top performance. SPECIFICATIONS OPERATOR SPECS GMax II 5900 GMax II 7900 Maximum Tip Size 1 gun to guns to gun to guns to guns to Maximum Delivery Rating 6.0 litres/min 8.3 litres/min Maximum Working Pressure 3300 psi (227 bar) 3300 psi (227 bar) Std Hose Length 15m 15m Engine 5.5 HP Honda Pull Start 6.5 HP Honda Pull Start ProConnect ü ü Typical Applications Continuous, heavy-duty striping requirements. Continuous, heavy-duty striping projects requiring higher output capacities ie. Airports. OPTIONAL EXTRAS 2nd Striping Gun Kit ü Standard Front Swivel Caster Wheel ü ü Bead Hopper and Dispenser ü ü QuickSelect Gun Selector* ü ü Purpose Built Tilt Trailer ü ü *QuickSelect Gun Selector - for simultaneous Paint & Beads 15

16 Graco LineLazer IV Airless Line Markers & Line In 1990 Graco introduced LineLazer, the innovative airless line marking system that revolutionised the line marking industry. Over the years, the LineLazer family of products has been improved to meet the ever changing needs of the road marking industry - each time delivering substantial benefits to the professional line marking contractor. LineLazer IV is now available as standard or with Auto-Layout System which continues the tradition of delivering innovation in user features and performance, creating an unmatched family of line markers. n LineLazer IV 200 HS with Line Driver and Accessories LineLazer 3400 The LineLazer 3400 is the preferred choice with contractors who are looking for professional performance and features, in a one-gun machine. n LineLazer 3400 Easy Reach controls Operator controls are located on the handle bars. Fine tune the line marking striping system operation without stopping. Chromex Pump Rod Long life rod treatment built for the most demanding applications. 4 times harder than ordinary chrome. Handle Bar Design A more natural, high-comfort design for greater line marking control and less operator fatigue. Contoured grips comfortably fit your hands. Swivel Front Wheel Provides easier up to the kerb car park marking with the ability to also mark arcs and curves. Tapered locking pin design for years of dependable operation. Electronic Pressure Control Accurate, tight tolerance system for excellent line quality. Easy-Roll Wheel Design Tall, low friction wheels push easier for reduced operator fatigue. 16

17 Driver LineLazer IV 3900 & 5900 Both the LineLazer IV 3900 and LineLazer IV 5900 models incorporate a range of substantial performance enhancements - designed specifically to deliver the most precise and consistent lines in the industry. Advanced Vibration Reduction System Removes engine vibration, taking line quality to the next level. Up to 60% less vibration at the spray tip. Chromex Pump Rod Long life rod treatment built for the most demanding applications 4 times harder than ordinary chrome Rear Gun Mount System Ability to place the guns near the rear axle for applying straighter long lines and smoother curved lines. Better gun visibility, especially on glass bead applications. Light Weight Gun Holder A full 25% lighter to minimise gun movement caused by rough pavement conditions Durable, extruded aluminium design Spring-assisted cable return for positive gun shut-off n LineLazer IV 3900 n LineLazer IV 5900 Flow-Through Easy-Out Filter Filter screen removes with the cap for convenient, mess-free access Flow-through design flushes faster for quicker colour changes Filters from the inside out LineLazer IV 200HS The LineLazer IV 200HS is the high production solution for medium to larger jobs that demand line perfection - every time! LineLazer IV 200HS Features Advanced Vibration Reduction System Rear Gun Mount System Light Weight Gun Holder Chromex Pump Rod Flow-through Easy Out Filter Cooling Fan Design Exclusive design delivers nearly 70% more air flow to keep the hydraulic pump running cool High-Capacity Cooling System 20% larger hydraulic fluid reservoir keeps the system running cool Innovative cooling fins wrap down and under the reservoir for improved air flow Smart-Control Pressure System Provides consistent spraying pressure, reducing pulsation and line variations n LineLazer IV 200HS with LineDriverHD n LineLazer IV 200HS 17

18 Graco LineLazers & LineDrivers The New Auto-Layout System Eliminate the hassle of manually spotting out car bays and pre-marking road lines with the all new Auto-Layout LineLazer. n LineLazer IV 3900 Auto-Layout System n LineLazer IV 5900 Auto-Layout System n LineLazer IV 200HS Auto-Layout System Less Hassle, Less Fatigue No bending to mark the lines Eliminates the strain to read the tape measure Takes the hassle out of calculating distances and car bay sizes Take the Pain Out Of Layout! No more tape measures No more calculation errors No more guessing No more sore backs No more wasted energy New Digital Display The display now shows psi, km/h, litre instant average, meterage, litres, and litre total all in one screen Simple push button design makes it easy to use Exclusive Durable Can Holder Design Folds up for on-board storage Pivots forward or backwards if hit n Accurately places layout dots for you n Simply Connect the Dots n LineDriver HD LineDriver and LineDriver HD Ride-On Striping Systems Connect the LineDriver to your LineLazer to help you double your line marking production. The LineDriver and LineDriver HD Ride-On Systems provide the most innovative user-friendly ride-on systems for the professional line marking contractor. n Pre-registration Safety Kit 18

19 LineLazer & LineDriver Specifications LINELAZER SPECIFICATIONS OPERATOR SPECS LineLazer 3400 LineLazer IV 3900 & With Auto-Layout System Maximum Tip Size 1 gun to gun to guns to LineLazer IV 5900 & With Auto-Layout System 1 gun to guns to LineLazer IV 200HS & With Auto-Layout System 1 gun to guns to Maximum Delivery Rating 2.8 litres/min 4.7 litres/min 6.0 litres/min 8.4 litres/min Maximum Working Pressure 3300 psi (227 bar) 3300 psi (227 bar) 3300 psi (227 bar) 3300 psi (227 bar) Engine 4.0 HP Honda Pull Start 4.0 HP Honda Pull Start 5.5 HP Honda Pull Start 5.5 HP Honda Pull Start Weight (No Paint or Beads) 65kg 96kg 105kg 125kg Material Sprayed Most common traffic paints and architectural coatings Most heavy, low VOC, waterborne and rubberised traffic paints Typical Applications Ideal for parking lots and seal coat contractors, schools, factories, etc Continuous, heavy-duty striping requirements Continuous, heavy-duty striping projects requiring high-output capacities Continuous, heavy-duty striping projects requiring higher-output capacities ie. Airports, Longitudinal Lines OPTIONAL EXTRAS LineDriver or LineDriver HD û ü ü ü EZ Bead System with two û ü ü ü dispensers EZ Bead Wind Deflectors û ü ü ü Line Pointer System - Short Pointer - Long Pointer û û ü ü ü ü ü ü LineLazer Light Kit û ü ü ü 57L Paint Hopper û ü ü ü Purpose Built Trailer for LineLazer & LineDriver û ü ü ü Light Kit Line Pointer System LINEDRIVER & LINEDRIVER HD SPECIFICATIONS OPERATOR SPECS LineDriver LineDriver HD Operating Speeds Forward to 16 km/h Reverse to 10 km/h Maintain striping speed within 0.16 km/h Forward to 16 km/h Reverse to 10 km/h Maintain striping speed within 0.16 km/h Engine 5.5 HP Honda Pull Start 6.5 HP Honda Pull Start Weight 120kg 125kg OPTIONAL EXTRAS Pre-registration Safety Kit ü ü EZ Bead System 57 Litre Paint Hopper n Combine LineLazer IV with LineDriver to create the ultimate ride-on line marking system 19

20 Graco RoadLazer RoadPak Modular Road Stripi The RoadLazer RoadPak System The Roadpak System is the latest innovation in road striping from Graco. It s a high production modular striping system that comes in eight ready-tostripe systems designed by Graco exclusively for you. Or you can design your own custom striping system that perfectly fits your unique striping needs. You decide. The RoadLazer Roadpak modular striping system allows you to either simply hook up an exclusive single hitch 1 or 2 pump striping system or, better yet, simply hook up an exclusive slide-in 1 or 2 pump striping system. Installation of the RoadPak System will depend on the number of options you choose but plan for 1 to 3 hours depending on your final choice of systems. You ll find that installing the RoadPak System is easy and simple to understand due to the plug and play compatibility of the choices available or ask A1 for a quote to install for you. 20

21 ng System SPECIFICATIONS Type Skid Max Litre/Minute Max Operating psi (bar) 2900 / 20 Max Spray Tips Four (4) Max Tip Size (1 Gun) Max Air 100 psi 13 Optional Double Bead Drop Yes Bead Capacity per tank 204kg Optional Bead Tanks (204kg) Up to four (4) tanks Optional Paint Tanks (125 litres) Up to four (4) tanks Double-Acting Guns Standard Optional Carriage Lift (Winch) Yes Pump Size (Rod Dia) 1.44 Stroke Length 12cm Cycle Per Litre 56 Guns Per Pump Two (2) Engine 18 HP Air Reservoir Standard Air QD Standard Air psi Gauge Standard Recirculation Back To Supply Standard Stroke Counters (Litre) Standard Hydraulic Reservoir 15 Litres Bead psi (bar) 60 / 4.1 Spray Guns Two (2) Bead Guns Two (2) Weight - 1 Pump RoadPak (24G624) 386kg - 2 Pump RoadPak (24G625) 431kg - 2 Pump Gun Arm (24G629) 61kg - Slide-In Mounting Frame (24G627) 77kg - Single Hitch Mounting Frame (24G626) 54kg n Heavy-Duty RPS 2900 Hydraulic System The heart of the RoadPak System is a proven performer. Its non-stall design provides the peace of mind you can only get from Graco designed products. n Displacement Pump System The Graco displacement pumps have delivered some of the best results in pumping striping paint for over 20 years. With maximum spray tip support at 2000 psi, the Graco pumps will spray the toughest traffic paints you ll ever need to use. With the new prime valve you can now recirculate paint to the container keeping it mixed and ready to go. n Heavy-Duty Compressor New 100 psi at 13.1 cfm means you now have all the air you need to make sure that your guns (paint and bead) are going to turn on and off to assure you the best possible starts and stops for your paint lines. Plus, you get a 8.3 litre Accumulation Tank for your air accessories, such as the hand bead gun. n Kohler Power 18 hp Kohler engine supplies the needed power for making sure you have a proven, reliable engine for your striping needs. With over 15 years of proven experience on the RoadLazer, Graco are confident Kohler will continue to deliver exceptional performance for years to come. n Heavy-Duty Modular Frame System Graco introduce the heavy-duty modular frame. Its small size allows it to fit most anywhere you need it to from the back of a truck, the bed of a ute or a flat bed truck this frame is built to last. It s also simple to add all the options you need to this frame as it s designed to allow multiple accessories to be easily added in minutes, optimising your striping system. 21

22 Graco ThermoLazer & ThermoLazer ProMelt ThermoLazer System The ThermoLazer striper is the most user-friendly, innovative thermoplastic striper to hit the streets. ThermoLazer ProMelt System Graco s breakthrough technology allows you to melt up to 136kg of thermoplastic on-board in less than an hour. n ThermoLazer The ThermoLazer & ThermoLazer ProMelt features the first ever ride-on solution with the capability to connect to a Graco LineDriver. This provides superior handling, improved line quality and increased productivity. With the LineDriver attached, the user is less fatigued and will get the job done faster. This unit is the first striper with dual rear wheels and a single front caster wheel that provides LineLazer-like handling the EasyGlide System. Graco recently introduced the world s first fast-melt, on-board thermoplastic striping system, the ThermoLazer ProMelt. The Graco ThermoLazer ProMelt System safely and easily melts 136 kg of thermoplastic material on board in less than one hour with a one man operation. This not only increases productivity from one job per day to up to three, but also reduces time, labour and capital costs by eliminating the need for expensive support systems like pre-melt kettle trucks or trailers and additional crew. n ThermoLazer Promelt The Graco ThermoLazer ProMelt System features the new SmartDie II system, the next generation in innovating steel design that enables use with or without heat for more flexibility in all weather conditions. Hardened steel dies with built-in mil thickness adjustment ensure durability. The SmartDie II system features no-spring heavy-duty construction that stays on the unit making it easier to clean without the need to remove it every time. This unique die system floats with the surface enabling accurate placement of thermoplastic and improved line quality. The no-tool die change-out system makes it fast and easy to switch line widths. 22

23 n EasyGlide Wheel Mount System Front mounted caster along with dual rear pneumatic air-filled tyres makes handling safe and easy to manoeuvre as a LineLazer striper n Ease-Z-Steer Handle Bar System Makes turning and handling simple as a LineLazer System Fully adjustable handles for users of all sizes n Split Bead Hopper System Split hopper holds over 40kg of beads Simple conversion to dual bead system with optional kit n Fat Track Front Swivel Wheel Proven front caster wheel system makes turning fast and easy Manoeuvre curves better No need to muscle it while moving n ProMelt Technology 4 Chamber Melting System more surface area to melt thermoplastic fast 100,000 BTUs faster melt time means more jobs get done everyday n Tri-Flame Die Heat System Reliable, safe system to keep die ready to use n Bead Dispense System No-tool system allows fast and flexible line width changes n SmartDie II Fast change-out system hardened steel dies with mil thickness adjustment system built-in Use with or without heat allows you to optimize your striping in all weather conditions Floats with the surface puts the thermoplastic where you want it for superior line quality External Heat System optional 4-torch die heat system SPECIFICATIONS Unit Model ThermoLazer System ThermoLazer ProMelt System Part Number 24H625 24H623 Bead Hopper Capacity 40 kg 40 kg Material Hopper Size 136 kg 136 kg Hopper Chamber Single QuadMelt Internal Mixing Paddles Dual PaddleMax System QuadMix System Hopper Lid System Flat, Dual Lid Raised, Single Lid Melt Time For 136 kg Thermoplastic hours Less than 1 hour Die Heater Tri-Flame Tri-Flame Main Burners 30,000 BTU 100,000 BTU Fuel Source LP Gas (Tank not included) LP Gas (Tank not included) Weight 133 kg 157 kg LineDriver Optional Extra Optional Extra Temperature Limit Control N/A 475 F Dies Available Smart Die / Smart Die II SmartDie II Dies Sizes Available (Inches) 3, 4, 5, 6, 7, 8, 9, 10,12, 3x3x3, 4x3x4, 4x4x4 3, 4, 5, 6, 7, 8, 9, 10,12, 3x3x3, 4x3x4, 4x4x4 External 4-Torch Die Heat System Optional Optional Weight 134kg 157kg Length 1830mm 1830mm Height 1300mm 1300mm Width 1220mm 1220mm LINEDRIVER & LINEDRIVER HD SPECIFICATIONS OPERATOR SPECS LineDriver LineDriver HD Operating Speeds Forward to 16 km/h Reverse to 10 km/h Maintain striping speed within 0.16 km/h Forward to 16 km/h Reverse to 10 km/h Maintain striping speed within 0.16 km/h Engine 5.5 HP Honda Pull Start 6.5 HP Honda Pull Start Weight 120kg 125kg OPTIONAL EXTRAS Pre-registration Safety Kit ü ü 23

24 Graco GrindLazer n GrindLazer 270 n GrindLazer 390 n GrindLazer 480 The GrindLazer 270 is the perfect scarifier for removing car park lines. It s EasyGlide Wheel Mount System makes it as easy to use as a LineLazer and its rugged, innovative design means you can count on it to perform for a lifetime of use. The GrindLazer 390 is the contractor choice for all-round scarifying jobs including car park lines, intersection markings, construction zones and sidewalk smoothing. With the optional LineDriver system its productivity is unmatched and means you can get more work done everyday without the fatigue from walking. The GrindLazer 480 is the high production choice when it comes to the most demanding scarifier jobs. With its Up-Cut cutting direction you not only are able to remove all types of lines found on car parks or roadways but now have the power to do inlay grooving jobs. Combined with the LineDriver you ll finish jobs faster and more accurately than ever before! Note: GrindLazer 480 with Reverse / Up-Cut cutting direction requires the use of a LineDriver System. The unit cannot operate without a LineDriver due to the ProStart safety switch interlock system. n GrindLazer 480 with LineDriver SPECIFICATIONS Unit Model GrindLazer 270 GrindLazer 390 GrindLazer 480 Maximum Working Width IN / CM 8 / / / 25 Engine Size CC / HP Honda 270 / 9 Honda 390 / 13 Vanguard 480 / 16 Front Tyre Pneumatic Air-Filled, Swivel Pneumatic Air-Filled, Swivel Pneumatic Air-Filled, Swivel Rear Tyres Pneumatic Air-Filled Pneumatic Air-Filled Pneumatic Air-Filled Drive Belt Style 3-Cog 3-Cog 3-Cog Cut Direction (Drum) Forward Forward Reverse / Up-Cut Clutch Heavy-Duty Centrifugal Heavy-Duty Centrifugal Extreme Duty Centrifugal Weight (KG) LineDriver Optional Extra Optional Extra Optional Extra Applications Traffic Paint Removal Thermoplastic Removal Smoothing Uneven Surfaces Traffic Paint Removal Thermoplastic Removal Smoothing Uneven Surfaces Epoxy Removal Traffic Paint Removal Thermoplastic Removal Smoothing Uneven Surfaces Inlay Grooving Removal Rate Walk 55 sq m / hr 74 sq m / hr N/A Removal Rate Ride 120 sq m / hr 158 sq m / hr 195 sq m / hr 24

25 Line Remover Paint Line Remover For low cost, fast efficient line removal Line Removal permanently! Up to 150mm wide line removal. Easy to use - Works in traffic, compact design suitable for concrete or asphalt. Centrifugal Clutch Easier starting. Enables engine to idle with cutter head resting on roadway, without machine moving forward. Works fast Self-propelling Revolutionary Line Remover Head Assembly Mounted between twin heavy-duty bearings, comprising five individual cutter shafts. Components heat-treated for longer life. n Cutter Head Assembly Hardened steel cutters shear off paint with high speed cutting action. Cutters are spaced on five shafts for 4 or 6 line removal. On the job cutter change takes only minutes. n Robust Construction Frame is heavy section welded steel plate reinforced at stress points, while cutter head assembly cover lid is 10 gauge steel plate. n Operator Protected by steel plate mounted rear of cutter head assembly. n Handle Wide bar with rubber grips ensure good control. Throttle control and cut-out switch mounted adjacent to handle bar. n Vee Belt Drive Guarded twin vee belts drive cutter assembly. Width of removed line Dimensions Weight Engine SPECIFICATIONS 25mm - 600mm 1220mm L x 650mm W x 920mm H 99kg 9 HP Briggs & Stratton Pull Start 25

26 Line Marking Products & Stencils n Line-O-Dots 100mm Plastic Line-O-Dots with peg. Available in White and Yellow. n Paint Supplied in 15 and/or 20 litre drums. Waterborne & Chlorinated Rubber. n Glass Beads Drop-on Glass Beads for high reflectivity of painted lines. Supplied in 25kg bags. n Thinners Cleaning thinners for line marking machine maintenance only. n Chalk Line Box & Chalk For setting out line marking. Supplied in 45 metre lengths of heavy duty line. Chalk is also available separately. n Spray Cans and Striper A full range of spray cans are available in assorted colours. For small jobs try the Superstriper aerosol line marking system. n Pavement Markers & Fixing Glue A full colour range of Reflective Pavement Markers, Ceramic Markers, Post Delineators and Glue Available. n Stencils A1 manufacture a complete range of custom made stencils including lettering, numbering, company logo s, graphics or plain text using 0.8mm - 2mm aluminium. Most stencils can be produced within hours at a very reasonable price. We also offer arrows & statcon markings using aluminium channel. 26

27 Graco FieldLazer Graco FieldLazer The Graco FieldLazer sets a new standard in sports field marking. This hardworking striper boasts plenty of features and capabilities to set it apart! With its low weight and specially designed cart, FieldLazer is easy to use on the field. Each component on FieldLazer is designed to deliver superior performance in a lightweight and compact package. At just 36kgs, FieldLazer weighs in as the easiest-to-push airless field striper. The exclusive tall-wheel cart rolls easily over ruts and cleat marks that can cause smaller wheeled machines to dip and dive. The result is less operator fatigue and straighter lines! Whether you spray mostly straight lines or fields full of lines, logos or numbers, FieldLazer s industry leading technology and many job-friendly features help you complete your jobs quickly and efficiently. Versatile and simple-to-use, it can help tackle your field marking jobs with ease. Max Working Pressure Max Delivery Pressure Spray Tip Selection 50mm (2 ) 100mm - 200mm (4-8 ) 200mm - 300mm (8-12 ) Engine Weight SPECIFICATIONS 900 psi (62 bar) 1.9 litre/min LL5217 LL5421 LL cc Honda 4-Stroke 36kg 27

28 A1 Roadlines Pty Ltd 89 Rushdale Street, Knoxfield Vic 3180 Telephone: Freecall: (A1ROAD) Facsimile: Website: