Series 600H. preliminary product guide. contents. features. Features 2. All new design. Mounting Configurations USt (18.

Transcription

1 Series 6H preliminary product guide features ll new design 2 USt (1.1 t) rating 9 ft (27.4 m) Four-section boom Full, mid-, and retracted span outriggers NEW Mentor LMI system Internal anti-two block Standard and rear mount options contents Features 2 Mounting onfigurations 3 Specifications 4 apacities imensions Specifications 13 ccessories 1 *Product may be shown with optional equipment.

2 features Why uy a National rane Series 6H: 6H 2 *Product may be shown with optional equipment. 2 USt (1.1 t) maximum capacity ft (42.7 m) w/optional jib maximum vertical reach* 1 ft (3. m) maximum vertical hydraulic reach* Mentor Load Moment Indicator system (LMI) Proportional boom extension High performance planetary winch Heavy-duty triple pump hydraulics * Maximum vertical reach is groundlevel to boom tip height at maximum extension and angle with outriggers/stabilizers fully extended. 2 USt (1.1 t) Rating The new 6H provides a 2 USt (1.1 t) capacity with six boom length options. 9 ft (27.4 m) Four-section oom The longest in its size range. The longer boom allows the operator to perform more lifts without the use of a jib, reducing setup time and improving efficiency. 3 ft (11. m) three-section boom, 49 ft (1 m) four-section boom, 6 ft (1.3 m) three-section boom, 71 ft (21.64 m) three-section boom, and ft (24.3 m) four-section boom are also availble. Overload Protection ll National rane boom trucks are equipped with overload protection: Mentor Load Moment Indicator (LMI) is standard on all series 6H machines with (WS) work area definition system. LMI display console is weatherproof. ll crane load lifting values are displayed simultaneously. Easy Glide oom Wear Pads Reduce the conditions that cause boom chatter and vibration. The net result is smoother crane operation. HO -style Outriggers Two sets of HO -style outriggers. Standard mount: 2 ft (6.9 m) full span, with ft (4.27 m) midspan setting with manual locks and reduced capacity chart, and fully retracted outrigger spread with reduced capacity chart. Rear mount: 1.3 ft (4.7 m) full span, with 13.3 ft (4. m) midspan setting with manual locks and reduced capacity chart, and fully retracted outrigger spread with reduced capacity chart. Main outriggers are equipped with removable ball and socket aluminum foot pads. Rotation The Series 6H is standard with 37 non-continuous rotation. djustable Swing Speed Standard on the 6H. control knob located on the swing motor brake release valve can be easily adjusted to the crane operator s swing speed preference. Heavier uty Torsion ox The stronger standard torsion box improves rigidity, reduces truck frame flex and reduces the need for counterweight. Speedy-reeve oom Tip and Sheave locks These standard features simplify rigging changes by decreasing the time needed to change line reeving. urst-of-speed Winch Provides faster winch payout and pickup of unloaded cable. Pre-painted omponents Painting crane components before assembly reduces the possibility of rust, improves serviceability and enhances the appearance of the machine. Improved Serviceability earings on the boom extend and retract cables can be greased through access holes in the boom side plates. Number of internal boom parts has been reduced, decreasing service time when rebuilding the machine. Internal anti-two-block wire routing eliminates damage potential. Electronic versions of manuals available through Manitowoc rane RE. New State-of-the-art ontrol Valve Provides smoother operation. The new design eliminates parts, reducing repair costs and improving the machine s serviceability. National rane is the Market Leader National rane is number one in the production of commercial truck-mounted boom trucks and has many programs and people directly and indirectly involved to provide our customers reliable products. National rane has the boom truck industry s leading test program. Every structural part of the crane is cycle tested up to 6, cycles at full capacity. In addition to cycle testing, each model is subjected to state-of-the-art strain gauge testing that measures metal deformation as small as one one-millionth of an inch. The net result is that any weak areas are caught in test, not on job sites where costly downtime occurs. Lift and telescoping cylinders are manufactured by National rane, so that the seals, packing glands, and end plates are traced for accurate shipment of replacement parts. Parts are available for all National rane machines, even if they are years old. National rane has a formalized quality program and is ISO 91 approved. National rane s Quality Management System is ISO 91:2 pproved.

3 mounting configuration The configurations are based on the Series 6H with an % stability factor. The complete unit must be installed in accordance with factory requirements and a test performed to determine actual stability and counterweight requirements since individual truck chassis vary. onfiguration 1 with Torsion ox 1 Full apacity Work rea Working area...1 Gross xle Weight Rating Front..., lb (6 kg) Gross xle Weight Rating Rear...34, lb (1,442 kg) Gross Vehicle Weight Rating...4, lb (21,3 kg) Wheelbase...26 in (6 cm) ab to xle/trunnion (/T) in (4 cm) Frame Section Modulus (SM) under crane: 11, PSI (7 MPa)...2 in 3 (327.7 cm 3 ) Frame Section Modulus (SM) over rear stabilizers: 11, PSI (7 MPa)...13 in 3 (213 cm 3 ) Stability Weight, Front...,7 lb (3946 kg) minimum* Stability Weight, Rear..., lb (6 kg) minimum* 3 This configuration is the least expensive method for the Model 6H. This mount, with the crane mounted behind the cab, requires the least weight of all mounts for stability; thus, you can haul larger payloads on your truck. It requires standard subbase and rear (SH) stabilizers. onfiguration 2 with Torsion ox 36 Full apacity Work rea Working area...36 Gross xle Weight Rating Front..., lb (6 kg) Gross xle Weight Rating Rear...34, lb (1,422 kg) Gross Vehicle Weight Rating...4, lb (21,3 kg) Wheelbase...26 in (6 cm) ab to xle/trunnion (/T) in (4 cm) Frame Section Modulus (SM) under crane: 11, PSI (7 MPa)...2 in 3 (32 cm 3 ) Frame Section Modulus (SM) over rear stabilizers: 11, PSI (7 MPa)...13 in 3 (213 cm 3 ) Stability Weight, Front...,7 lb (3946 kg) minimum* Stability Weight, Rear...,6 lb (391 kg) minimum* Requires front SFO stabilizer to give machine full capacity 36 around the truck. Truck must meet the minimum requirements above. Front stabilizer gives the machine a solid base, helping the operator control loads precisely. Extended front frame rails required for SFO installation. onfiguration 3 with Torsion ox Rear Mount Working area...36 Gross xle Weight Rating Front..., lb (443 kg) Gross xle Weight Rating Rear...34, lb (1,422 kg) Gross Vehicle Weight Rating...46, lb (2,6 kg) Wheelbase...26 in (6 cm) ab to xle/trunnion (/T)... in (396 cm) Frame Section Modulus (SM) under crane: 11, PSI (7 MPa) in 3 (2 cm 3 ) Frame Section Modulus (SM) over rear stabilizers: 11, PSI (7 MPa) in 3 (2 cm 3 ) Stability Weight, Front...6, lb (294 kg) minimum* Stability Weight, Rear...9, lb (439 kg) minimum* llows the installation of the Model 6H on a chassis. In most cases, the chassis will not require reinforcing, and the amount of counterweight required is minimized, increasing payload capacities. Extended front frame rails required for SFO installation. Notes: Gross Vehicle Weight rating (GVWR) is dependent on all components of the vehicle (axles, tires, springs, frame, etc.) meeting manufacturers recommendations: always specify GVWR when purchasing trucks iesel engines require a variable speed governor and energize-to-run fuel solenoid for smooth crane operation; electronic fuel injection requires EET engine remote throttle ll mounting data is based on a National Series 6H with an percent stability factor *Estimated axle scale rates prior to installation of crane, stabilizers and subbase for % stability. The complete unit must be installed in accordance with factory requirements, and a test performed to determine actual stability and counterweight requirements per SE J; contact the factory for details Transmission neutral safety interlock switch is required with optional remote control 6H

4 specifications oom and Jib ombinations ata 4 vailable in six basic models. Model 63H Equipped with a -3 ft ( m) three-section boom. Maximum tip height is 4 ft (.63 m) (no jib option available). -3 ft ( m) three-section boom Model 649H Equipped with a -49 ft (4.-1 m) four-section boom. This model can be equipped with a 1-2 ft ( m) two section jib. Maximum tip height w/2 ft (7.6 m) jib is 7 ft (26. m). -49 ft (4.-1 m) four-section boom 6FJ2M 1-2 ft ( m) two-section jib Model H Equipped with a 24-6 ft ( m) three-section boom. Maximum tip height is 7 ft (21.3 m) (no jib option available) ft ( m) three-section boom Model 671H Equipped with a ft ( m) three-section boom. This model can be equipped with a 2- ft ( m) two-section jib. Maximum tip height w/ ft (13.72 m) jib is ft (3.2 m) ft ( m) three-section boom 6FJM 2- ft ( m) two-section jib Model H Equipped with a 24- ft ( m) four-section boom. Maximum tip height is 9 ft (27.44 m) (no jib option available). 24- ft ( m) four-section boom Model 69H Equipped with a 27-9 ft ( m) four-section boom. This model can be equipped with a 2- ft ( m) two section jib. Maximum tip height w/ ft (13.72 m) jib is 4 ft (43.9 m) ft ( m) four-section boom 6FJM 2- ft ( m) two-section jib Note: Maximum tip is measured with outriggers/stabilizers fully extended. 6H Winch ata 6H Winch ata ll winch pulls and speeds in this chart are shown on the fourth layer Winch line pulls would increase on the first and second layers Winch line pulls may be limited by the winch capacity or the NSI to 1 cable safety factor, shown below this chart Hook blocks are rated at maximum capacity for the block. o not exceed rated cable pull with any block. 1 Part Line 2 Part Line 3 Part Line 4 Part Line Part Line 6 Part Line able verage reaking Max. Max. Max. Max. Max. Max. Winch Supplied Strength Pull Pull Pull Pull Pull Pull Standard 9/ in iameter 3, lb 7,7 lb ( kg) 1,4 lb ( kg) 23,1 lb (1 4.9 kg) 3, lb ( kg) 3, lb (.96 kg) 4, lb (.96 kg) Planetary Winch Rotation Resistant (17,463 kg) 6H Layer Winch Pull Winch Speed OS Winch Speed Rope apacity lb (kg) fpm (mpm) fpm (mpm) ft (m) 1 1,3 (47) 17 (4) 222 () ,36 (4246) 17 (3) 246 (7) ,2 (36) 192 (9) 271 (3) ,2 (47) 29 (64) 294 (9) ,23 (3279) 27 (69) 31 (97) 394 NOTE: ll ratings based on 34 GPM at 33 psi (.7 LPM at 22.7 MPa) urst of Speed maximum pull = 3 lb (13 kg) Winch are rum Pull llowable able Pull With standard rotation resistant rope...1,2 lb (4627 kg)...7,7 lb (3493 kg) lock Type Rating Weight ownhaul Weight...3. USt (3.49 t)...1 lb ( kg) 1 Sheave lock USt (1.4 t)...2 lb (91 kg) 2 Sheave lock USt (17.46 t)...3 lb (1 kg)

5 capacities Load Rating hart: Series 671H (21.6 m) oom with ft (13.7 m) Jib/Fullspan Outrigger 17.3 ft (.3 m) & Stabilizer Other Series 6H Load Rating harts are available. National rane will send you a chart on request or you may secure needed load rating information through your nearest National rane dealer. 2 nd Jib ft 1 st Jib 2 ft LENGTH IN FEET RIUS IN FEET 17'-4" FULL SPN OUTRIGGER LOK PINS MUST E ISENGGE o not 2 extend 4 1 jib into this 2-1 area SERIES 671H WITH ' JI FULL SPN OUTRIGGERS FULL SPN RER STILIZER HEIGHT IN FEET LMI OPERTING OE OPERTING MOE 1 Main oom No Jib Stowed 2 Main oom - Jib Stowed 3 2 ft. Tele Jib 4 ft. Tele Jib 11 Man asket On Main oom 13 Man asket on 2 ft. Tele Jib Man asket on 4 ft. Tele Jib UTION: o not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. o not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factoryapproved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. lways level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. o not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. SERIES 671H (21.6 M) WITH FT (13.7 M) JI/ FULLSPN OUTRIGGER & STILIZER NOTE: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. o not exceed rated jib capacities at any reduced boom lengths. LOLINE EQUIPMENT EUT. ownhaul weight...1 lb ( kg) One sheave block...2 lb (9.7 kg) Two sheave block...3 lb (1 kg) Load Rating hart: Series 671H (21.6 m) oom with ft (13.7 m) Jib/Fullspan Outrigger 17.3 ft (.3 m) & Stabilizer RIUS (ft) FT 4, 2, 21, 17,9,,9 11,3 7,6 4, FT 24,7 21, 17,9 1, 13,7 11,1,9 6,6 3, FT 24,2 2, 17, 1, 13,6 1,9,7 7,1, 4,1 1, FT 2,1 17,1 1, 13,2 1,7, 7,, 4,9 4, 2, 1, FT,,4,7 1,,3 6,,7 4, 4, 3,4 2,7 1, FT,, 1,, 6,6,7 4, 4,1 3, 3, 2, 1,9 *SHE RES RE STRUTURLLY LIMITE PITIES 6H THIS HRT IS ONLY GUIE N SHOUL NOT E USE TO OPERTE THE RNE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

6 capacities 6 Load Rating hart: Series 671H (21.6 m) oom with ft (13.7 m) Jib/Midspan Outrigger 1. ft (3. m) & Stabilizer Other Series 6H Load Rating harts are available. National rane will send you a chart on request or you may secure needed load rating information through your nearest National rane dealer. 2 nd Jib ft 1 st Jib 2 ft LENGTH IN FEET ' MI SPN OUTRIGGER LOK PINS MUST E ENGGE o not 3 extend 2. 4 boom or 2 jib into 1 this area RIUS IN FEET SERIES 671H (21.6 M) WITH FT (13.7 M) JI/MISPN OUTRIGGER & STILIZER SERIES 671H WITH ' JI MI SPN OUTRIGGERS MI SPN RER STILIZER HEIGHT IN FEET LMI OPERTING OE OPERTING MOE 21 Main oom - No Jib Stowed 22 Main oom - Jib Stowed 23 2 ft. Tele Jib 24 ft. Tele Jib LOLINE EQUIPMENT EUT ownhaul weight...1 lb ( kg) One sheave block...2 lb (9.7 kg) Two sheave block...3 lb (1 kg) UTION: o not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. o not exceed capacities at reduced radii. Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended and the outrigger lock pins engaged on a firm, level surface and the crane leveled and mounted on a factory recommended truck. lways level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. o not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. NOTE: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. o not exceed rated jib capacities at any reduced boom lengths. Load Rating hart: Series 671H (21.6 m) oom with ft (13.7 m) Jib/Midspan Outrigger 1. ft (3. m) & Stabilizer 6H RIUS (ft) FT 4, 2, 21, 1, 11,,9,9 3, 3, FT 24,7 21, 1, 11, 9,3 6,2 4,1 2, 2, FT 24,2 2,,2,2 9,6 6, 4,3 3,2 2,1 1, 1, FT 2,1,,4 9, 6,6 4, 3,2 2,3 1,7 1,2 *SHE RES RE STRUTURLLY LIMITE PITIES THIS HRT IS ONLY GUIE N SHOUL NOT E USE TO OPERTE THE RNE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane FT,, 9,9 6,7 4,6 3,3 2,4 1, 1, FT, 1,1 6,9 4,7 3,4 2, 1, 1,4 1, 7

7 capacities Load Rating hart: Series H (23.4 m) oom/fullspan Outrigger 17.3 ft (.3 m) & Stabilizer Other Series 6H Load Rating harts are available. National rane will send you a chart on request or you may secure needed load rating information through your nearest National rane dealer. LENGTH IN FEET RIUS IN FEET LMI OPERTING OE OPERTING MOE 1 Main oom No Jib Stowed 11 Man asket On Main oom SERIES H (23.4 M) / FULLSPN OUTRIGGER & STILIZER SERIES H NO JI FULL SPN OUTRIGGERS FULL SPN RER STILIZER HEIGHT IN FEET 17'-4" FULL SPN OUTRIGGER LOK PINS MUST E ISENGGE. LOLINE EQUIPMENT EUT ownhaul weight...1 lb ( kg) One sheave block...2 lb (9.7 kg) Two sheave block...3 lb (1 kg) UTION: o not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. o not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factory-approved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. lways level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. o not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. 7 Load Rating: Series H (23.4 m) oom/ Fullspan Outrigger 17.3 ft (.3 m) & Stabilizer 6H RIUS (ft) FT 4, 27,1 22,4 19, 17,1,7 11,1, FT 2,4 21,4 1,,,2 11, 9,1 7, 3, FT 2,6 17, 1,3 13, 11, 9, 7,2, 4,6 2,6 1,7 FT 69 FT FT THIS HRT IS ONLY GUIE N SHOUL NOT E USE TO OPERTE THE RNE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane ,,7 13, 1,, 7,,9 4, 4,1 3, 2,2 1, ,1 1,1,2 6,,7 4, 4,1 3, 2,9 2, 1, ,, 6,, 4,6 4, 3, 3, 2, 2,1 1,7 1,1 Shaded areas are structurally limited capacities

8 capacities Load Rating hart: Series H (23.4 m) oom/midspan Outrigger 1 ft (3. m) & Stabilizer Other Series 6H Load Rating harts are available. National rane will send you a chart on request or you may secure needed load rating information through your nearest National rane dealer. LENGTH IN FEET RIUS IN FEET LMI OPERTING OE OPERTING MOE 21 Main oom - No Jib Stowed SERIES H (23.4 M) / MISPN OUTRIGGER & STILIZER 36 4 o not extend boom into this area SERIES H NO JI MI SPN OUTRIGGERS MI SPN RER STILIZER HEIGHT IN FEET 1' MI SPN OUTRIGGER LOK PINS MUST E ENGGE. LOLINE EQUIPMENT EUT ownhaul weight...1 lb ( kg) One sheave block...2 lb (9.7 kg) Two sheave block...3 lb (1 kg) UTION: o not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. o not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factory-approved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. lways level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. o not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. Load Rating: Series H (23.4 m) oom/ Midspan Outrigger 1 ft (3. m) & Stabilizer 6H RIUS (ft) FT 4, 27,1 22,4 19,, 9,9 6,, FT 2,4 21,4 1,, 1,3 6, 4, 3,1 2, FT 2,6 17, 1,3 13, 7, 4,6 3,2 2,2 1, 1, 1, THIS HRT IS ONLY GUIE N SHOUL NOT E USE TO OPERTE THE RNE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane FT 17,,7 13, 7,2 4, 3, 2,4 1,6 1, FT,1 7, 4,9 3, 2, 1,7 1, FT,,1 3,6 2,6 1,9 1, 9 Shaded areas are structurally limited capacities

9 capacities Load Rating hart: Series 69H (27.4 m) oom with ft (13. 7 m) Jib/Fullspan Outrigger 17.3 ft (.3 m) & Stabilizer Other Series 6H Load Rating harts are available. National rane will send you a chart on request or you may secure needed load rating information through your nearest National rane dealer. 2nd Jib ft 1st Jib 2 ft LENGTH IN FEET RIUS IN FEET 1'-3" FULL SPN OUTRIGGER LOK PINS MUST E ISENGGE. SERIES 69H (27.4 M) WITH FT (13.7 M) JI/ FULLSPN OUTRIGGER & STILIZER o not extend 3 jib into this 2 area SERIES 69H WITH ' JI FULL SPN OUTRIGGERS FULL SPN RER STILIZER HEIGHT IN FEET LMI OPERTING OE OPERTING MOE 1 Main oom No Jib Stowed 2 Main oom - Jib Stowed 3 2 ft. Tele Jib 4 ft. Tele Jib 11 Man asket On Main oom 13 Man asket on 2 ft. Tele Jib Man asket on 4 ft. Tele Jib LOLINE EQUIPMENT EUT ownhaul weight...1 lb ( kg) One sheave block...2 lb (9.7 kg) Two sheave block...3 lb (1 kg) UTION: o not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. o not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factory-approved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. lways level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. o not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. NOTE: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. o not exceed rated jib capacities at any reduced boom lengths. Load Rating hart: Series 69H (27.4 m) oom with ft (13.7 m) Jib/Fullspan Outrigger 17.3 ft (.3 m) & Stabilizer 9 6H RIUS (ft) FT 4, 2,7 21,4 1,,4,7 11,2 7, 4, FT 2,9 17,7 1,2 13,3 1, 9, 7,,2 1, FT 17, 1, 13,2 1,,1 6,7,7 4,6 3, 2, FT 7 FT 9 FT THIS HRT IS ONLY GUIE N SHOUL NOT E USE TO OPERTE THE RNE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane ,,6 9,9 7,9 6,, 4, 3, 3,1 2, 1, ,7 7,7 6,2,2 4,4 3,7 3,1 2,6 2,2 1,7 1, , 7, 6,1, 4,2 3, 3, 2, 2,1 1, 1, 1,1 Shaded areas are structurally limited capacities

10 capacities 1 Load Rating hart: Series 69H (27.4 m) oom with ft (13.7 m) Jib/Midspan Outrigger 1 ft (3. m) & Stabilizer Other Series 6H Load Rating harts are available. National rane will send you a chart on request or you may secure needed load rating information through your nearest National rane dealer. 2nd Jib ft 1st Jib 2 ft LENGTH IN FEET '-3" MI SPN OUTRIGGER LOK PINS MUST E ENGGE o not 3 extend 6 2 jib into boom or 4 this 1 area RIUS IN FEET SERIES 69H (27.4 M) WITH FT (13.7 M) JI/ MISPN OUTRIGGER & STILIZER SERIES 69H WITH ' JI MI SPN OUTRIGGERS MI SPN RER STILIZER HEIGHT IN FEET LMI OPERTING OE OPERTING MOE 21 Main oom - No Jib Stowed 22 Main oom - Jib Stowed 23 2 ft. Tele Jib 24 ft. Tele Jib LOLINE EQUIPMENT EUT ownhaul weight...1 lb ( kg) One sheave block...2 lb (9.7 kg) Two sheave block...3 lb (1 kg) UTION: o not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. o not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factory-approved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. lways level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. o not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. NOTE: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. o not exceed rated jib capacities at any reduced boom lengths. Load Rating: Series 69H (27.4 m) oom/ Fullspan Outrigger 1 ft (3. m) & Stabilizer 6H RIUS (ft) FT 4, 2,7 21,4 1,,4,7 11,2 7, 2, FT 2,9 17,7 1,2 13,3 1,, 6,1 4, FT 17, 1, 13,2 1,,1 6,3 4,7 3, 2, 2,1 THIS HRT IS ONLY GUIE N SHOUL NOT E USE TO OPERTE THE RNE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane FT,,6 9,9 7,9 6, 4,9 3,7 2,9 2, 1,7 1, FT 9,7 7,7 6,2 4,9 3, 2,9 2,3 1, 1,4 1, FT 7, 7,6 6,2, 3,9 3,1 2,4 1,9 1, 1,1 Shaded areas are structurally limited capacities

11 capacities Load Rating hart: RER MOUNT Series 69H (27.4 m) oom with ft (13. 7 m) Jib/Fullspan Outrigger 1.3 ft (4.7 m) & Stabilizer Other Series 6H Load Rating harts are available. National rane will send you a chart on request or you may secure needed load rating information through your nearest National rane dealer. 2nd Jib ft 1st Jib 2 ft LENGTH IN FEET RIUS IN FEET 17'-4" FULL SPN OUTRIGGER LOK PINS MUST E ISENGGE. SERIES 69H (27.4 M) WITH FT (13.7 M) JI/ FULLSPN OUTRIGGER & STILIZER o not extend 3 jib into this 2 area SERIES 69H WITH ' JI FULL SPN OUTRIGGERS FULL SPN RER STILIZER HEIGHT IN FEET LMI OPERTING OE OPERTING MOE 1 Main oom No Jib Stowed 2 Main oom - Jib Stowed 3 2 ft. Tele Jib 4 ft. Tele Jib 11 Man asket On Main oom 13 Man asket on 2 ft. Tele Jib Man asket on 4 ft. Tele Jib LOLINE EQUIPMENT EUT ownhaul weight...1 lb ( kg) One sheave block...2 lb (9.7 kg) Two sheave block...3 lb (1 kg) UTION: o not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. o not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factory-approved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. lways level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. o not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. NOTE: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. o not exceed rated jib capacities at any reduced boom lengths. Load Rating hart: RER MOUNT Series 69H (27.4 m) oom with ft (13.7 m) Jib/Fullspan Outrigger 1.3 ft (4.7 m) & Stabilizer 11 6H RIUS (ft) FT 4, 2,7 21,4 1,,4,7 11,2 7, 4, FT 2,9 17,7 1,2 13,3 1, 9, 7,,2 1, FT 17, 1, 13,2 1,,1 6,7,7 4,6 3, 2, FT,,6 9,9 7,9 6,, 4, 3, 3,1 2, 1, FT 9,7 7,7 6,2,2 4,4 3,7 3,1 2,6 2,2 1,7 1, FT 7, 7, 6,1, 4,2 3, 3, 2, 2,1 1, 1, 1,1 Shaded areas are structurally limited capacities THIS HRT IS ONLY GUIE N SHOUL NOT E USE TO OPERTE THE RNE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

12 capacities Load Rating hart: RER MOUNT Series 69H (27.4 m) oom with ft (13.7 m) Jib/Midspan Outrigger 13.3 ft (4.1 m) & Stabilizer Other Series 6H Load Rating harts are available. National rane will send you a chart on request or you may secure needed load rating information through your nearest National rane dealer. LENGTH IN FEET o not 41 3 extend 6 boom or 27 2 jib into 4 this 1 area RIUS IN FEET 2nd Jib ft 1st Jib 2 ft 1' MI SPN OUTRIGGER LOK PINS MUST E ENGGE. SERIES 69H (27.4 M) WITH FT (13.7 M) JI/ MISPN OUTRIGGER & STILIZER SERIES 69H WITH ' JI MI SPN OUTRIGGERS MI SPN RER STILIZER HEIGHT IN FEET LMI OPERTING OE OPERTING MOE 21 Main oom - No Jib Stowed 22 Main oom - Jib Stowed 23 2 ft. Tele Jib 24 ft. Tele Jib LOLINE EQUIPMENT EUT ownhaul weight...1 lb ( kg) One sheave block...2 lb (9.7 kg) Two sheave block...3 lb (1 kg) UTION: o not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. o not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factory-approved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. lways level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. o not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. NOTE: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. o not exceed rated jib capacities at any reduced boom lengths. Load Rating: RER MOUNT Series 69H (27.4 m) oom with ft (13.7 m) Jib/ Fullspan Outrigger 13.3 ft (4.1 m) & Stabilizer 6H RIUS (ft) FT 4, 2,7 21,4 1,,4,7 11,2 7, 2, FT 2,9 17,7 1,2 13,3 1,, 6,1 4, FT 17, 1, 13,2 1,,1 6,3 4,7 3, 2, 2, FT,,6 9,9 7,9 6, 4,9 3,7 2,9 2, 1,7 1, FT 9,7 7,7 6,2 4,9 3, 2,9 2,3 1, 1,4 1, FT 7, 7,6 6,2, 3,9 3,1 2,4 1,9 1, 1,1 Shaded areas are structurally limited capacities THIS HRT IS ONLY GUIE N SHOUL NOT E USE TO OPERTE THE RNE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

13 dimensions specifications standard mount 13 6H G ENTER OF GRVITY FROM ENTERLINE Series G H RY WEIGHT* W/OIL WEIGHT* 671H in [1 cm] 2.92 in [134 cm] 1, lb [7,1 kg],69 lb [7,7 kg] H in [ cm].9 in [2 cm],236 lb [7,36 kg] 17,9 lb [7,72 kg] 69H. in [197 cm] 6. in [13 cm] 17,63 lb [,7 kg] 1,1 lb [,39 kg] * OVE WEIGHTS O NOT INLUE RESERVOIR, RSO, JI, PTO, PUMP, E ** WEIGHT INLUES, WINH, ROPE, TURRET, LIFT YLINER, FRME, ONTROLS, OUTRIGGERS, PLTFORMS, TORQUE OX, REST, UMPER, OWNHUL WEIGHT UNITS IN INHES UNLESS SPEIFIE

14 dimensions specifications rear mount 6H G ENTER OF GRVITY FROM ENTERLINE Series G H RY WEIGHT* W/OIL WEIGHT* 671H 9.9 in [244 cm] 1.2 in [13 cm] 17,1 lb [7,73 kg] 17,3 lb [7,1 kg] H 9.9 in [229 cm].3 in [ cm] 17,927 lb [,132 kg] 1, lb [,2 kg] 69H 99.4 in [23 cm] 7.34 in [6 cm] 1,71 lb [,49 kg] 1,7 lb [,67 kg] * OVE WEIGHTS O NOT INLUE RESERVOIR, RSO, JI, PTO, PUMP, E ** WEIGHT INLUES, WINH, ROPE, TURRET, LIFT YLINER, FRME, ONTROLS, OUTRIGGERS, PLTFORMS, TORQUE OX, REST, UMPER, OWNHUL WEIGHT UNITS IN INHES UNLESS SPEIFIE

15 Radio Remote ontrols Eliminate the handling and maintenance concerns that accompany cabled remotes. Operate to a range of about 2 ft ( m), varying with conditions. One-Person asket Strong but lightweight steel basket with 3 lb (139 kg) capacity, gravity hung with swing lock and full body harness. accessories R4R 1-S 21-S (for dual locking baskets) 1 Heavy-duty Personnel asket 1,2 lb (44 kg) capacity steel basket with safety loops for four passengers. Gravity leveling 72 x 42 inch (13 x 17 cm) platform. Fast attachment and secure locking systems. Load chart must show 2,3 lb (3 kg) minimum to operate this accessory. Hydraulic Oil ooler utomatic, self-contained radiator system with electric fans cools oil under continuous operation. Winch rum Rotation Indicator Last Wrap Indicator Option on winch with indicator on Easy Reach console. Single Front Outrigger enter front stabilizer with a 2 in vertical stroke S-1 S-R1 (provides rotation) O WRI LLI SFO Steel Tool ox Options ulkhead-steel for super-duty beds Spanish-Language anger ecals, ontrol Knobs, and Operators Manuals HS S SOM 6H

16 Regional Headquarters mericas Manitowoc, Wisconsin, US Tel: Fax: Shady Grove, Pennsylvania, US Tel: Fax: Europe, Middle East, frica Ecully, France Tel: Fax: sia Pacific Shanghai, hina Tel: Fax: Singapore Tel: Fax: Regional Offices mericas razil lphaville Tel: Fax: Mexico Monterrey Tel: Fax: Europe, Middle East, frica lgeria Hydra Tel: Fax: zeck Republic Netvorice Tel: Fax: France audemont Tel: Fax: ergy Tel: Fax: ecines Tel: Fax: Germany Langenfeld Tel: Fax: Hungary udapest Tel: Fax: Italy Parabiago Tel: Fax: Netherlands reda Tel: Fax: Poland Warsaw Tel: Fax: Portugal lfena Tel: Fax: Lisbon Tel: Fax: Russia Moscow Tel: Fax: U..E. ubai Tel: Fax: U. K. Middlesex Tel: Fax: Sunderland Tel: Fax: sia Pacific ustralia Melbourne Tel: Fax: Sydney Tel: Fax: hina eijing Tel: Fax: Xi an Tel: Fax: Korea Seoul Tel: Fax: Philippines Makati ity Tel: Fax: Factories razil lphaville hina Zhangjiagang France harlieu La layette Moulins Germany Wilhelmshaven India alcutta Pune Italy Niella Tanaro Portugal Fânzeres U.S.. Manitowoc Port Washington Shady Grove onstant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment and price changes without notice. Illustrations shown may include optional equipment and accessories, and may not include all standard equipment. 2 MNITOWO Printed in US Form No. 6H PG Part No. 6H / 2 / 1M