National Crane 600H Series

Transcription

1 National Crane 6H Series Product Guide Features 18,1 t (2 USt) rating Six boom options available from 11,58 m (38 ft) to 27,42 m (9 ft) Full-, mid-, and retracted-span outriggers Mentor LMI System Internal anti-two block wiring Standard and rear mount options

2 Features National Crane Series 6H 18,1 t (2 USt) maximum capacity 3,2 m (99 ft) maximum tip height (main boom) 43,95 m (144 ft) maximum tip height (boom with jib) oom At 27,5 m (9 ft) the 6H series four-section boom is the longest in its size range. The longer boom allows the operator to perform more lifts without the use of a jib, reducing setup time and improving efficiency. A 11,58 m (38 ft) three-section boom, 15 m (49 ft) four-section boom, 18,3 m (6 ft) threesection boom, 21,64 (71 ft) three-section boom, and 24,38 m (8 ft) four-section boom are also available. Overload protection Mentor Load Moment Indicator (LMI) with work area definition system (WADS) is standard on all Series 6H machines. The LMI display console is weatherproof and displays all crane load lifting values simultaneously. "HO"-style outriggers Standard Mount: Two sets of HO -style outriggers with 5,28 m (17 ft 4 in) span, with 3,4 m (1 ft) mid span setting with manual locks and reduced capacity chart and fully retracted outrigger spread with reduced capacity chart. Rear Mount: 4.7 m (15.3 ft) full span, with 4,5 m (13.3 ft) midspan setting with manual locks and reduced capacity chart and fully retracted outrigger spread with reduced capacity chart. Main outriggers are equipped with removable ball and socket aluminum foot pads standard.

3 Features Improved serviceability and reliability helps keep you working longer earings on the boom and retract cables can be greased through access holes in the boom side plates Number of internal boom parts has been reduced, deceasing service time Internal anti-two-block wire routing eliminates damage potential Painting crane components before assembly reduces the possibility of rust and enhances the appearance of the machine State of the art control valve provides smoother operation. The new design eliminates parts, reducing repair costs and improving the machines serviceability Easy-reeve boom tip and sheave blocks simplify rigging changes by decreasing the time needed to change line reeving Performance you can rely on The Series 6H is standard with 375 non-continuous rotation The optional duty cycle package which includes a burst of speed winch provides faster winch payout and pickup of unloaded cable The stronger standard torsion box improves rigidity, reduces truck frame flex and reduces the need for counterweight A control knob located on the swing motor brake release valve can be easily adjusted to the crane operator's swing speed preference Easy Glide oom Wear Pads reduce the conditions that cause boom chatter and vibration. The net result is smoother crane operation.

4 Contents Features 2 Mounting configurations 5 Specifications 6 Capacities 7 Dimensions specifications 14 Accessories 15 4

5 Mounting configuration The configurations are based on the Series 6H with an 85% stability factor. The complete unit must be installed in accordance with factory requirements and a test performed to determine actual stability and counterweight requirements since individual truck chassis vary. 6." Front jack required for 36 work area 6." 44.69" 6." W 44.69" 192." 6." W 192." 14.31" 14.31" Tandem 2' ed 66." 111." Tandem 2' ed 66." 111." 92." 92." " Top of truck frame rail " Top of truck frame rail Configuration 1 with torsion box 18 full capacity work area Working area Gross axle weight rating front... 6 kg (14, lb) Gross axle weight rating rear... 15,442 kg (34, lb) Gross vehicle weight rating... 21,773 kg (48, lb) Wheelbase... cm (6 in) Cab to axle/trunnion (CA/CT) cm (192 in) Frame Section Modulus (SM) under crane: 758 MPa (11, PSI) ,7 cm 3 ( 2 in 3 ) Frame Section Modulus (SM) over rear stabilizers: 758 MPa (11, PSI) cm 3 (13 in 3 ) Stability weight, front kg (87 lb) minimum* Stability weight, rear kg (86 lb) minimum* This configuration is the least expensive method for the Model 6H. This mount, with the crane mounted behind the cab, requires the least weight of all mounts for stability; thus, you can haul larger payloads on your truck. It requires standard subbase and rear (ASH) stabilizers. *Weights do not include RSOD, PTO, pumpt, bed and SFO. Configuration 2 with torsion box 36 full capacity work area Working area...36 Gross axle weight rating front... 6 kg (14, lb) Gross axle weight rating rear... 15,422 kg (34, lb) Gross vehicle weight rating... 21,773 kg (48, lb) Wheelbase... cm (6 in) Cab to axle/trunnion (CA/CT) cm (192 in) Frame Section Modulus (SM) under crane: 758 MPa (11, PSI) cm 3 (2 in 3 ) Frame Section Modulus (SM) over rear stabilizers: 758 MPa (11, PSI) cm 3 (13 in 3 ) Stability weight, front kg (87 lb) minimum* Stability weight, rear kg (86 lb) minimum* Requires front SFO stabilizer to give machine full capacity 36 around the truck. Truck must meet the minimum requirements above. Front stabilizer gives the machine a solid base, helping the operator control loads precisely. Extended front frame rails required for SFO installation. *Weights do not include RSOD, PTO, pumpt, bed and SFO. 2.19" 92.49" 23." 192." 6." ' ed Tandem 78." 129." 44.69" " Top of truck frame rail Configuration 3 with torsion box rear mount Working area...36 Gross axle weight rating front kg (12, lb) Gross axle weight rating rear... 15,422 kg (34, lb) Gross vehicle weight rating... 2,8 kg (46, lb) Wheelbase... cm (6 in) Cab to axle/trunnion (CA/CT) cm (192 in) Frame Section Modulus (SM) under crane: 758 MPa (11, PSI) cm 3 (15.9 in 3 ) Frame Section Modulus (SM) over rear stabilizers: 758 MPa (11, PSI) cm 3 (15.9 in 3 ) Stability weight, front kg ( lb) minimum* Stability weight, rear kg (95 lb) minimum* Allows the installation of the Model 6H on a chassis. In most cases, the chassis will not require reinforcing, and the amount of counterweight required is minimized, increasing payload capacities. *Weights do not include RSOD, PTO, pumpt, bed and SFO. Notes: Gross Vehicle Weight rating (GVWR) is dependent on all components of the vehicle (axles, tires, springs, frame, etc.) meeting manufacturers recommendations: always specify GVWR when purchasing trucks Diesel engines require a variable speed governor and energize-to-run fuel solenoid for smooth crane operation; electronic fuel injection requires EET engine remote throttle All mounting data is based on a National Series 6H with an 85 percent stability factor The complete unit must be installed in accordance with factory requirements, and a test performed to determine actual stability and counterweight requirements per SAE J7; contact the factory for details Transmission neutral safety interlock switch is required with optional radio remote control National Crane 6H *Estimated axle scale rates prior to installation of crane, stabilizers and subbase for 85% stability. 5

6 Specifications oom and jib combinations data Available in six basic models. Model 638H Equipped with a 4,88 m - 11,58 m ( ft - 38 ft) three-section boom. Maximum tip height is 14,63 m (48 ft) (no jib option available). 4,88 m -11,58 m ( ft - 38 ft) three-section boom Model 649H Equipped with a 4,88 m -15 m ( ft - 49 ft) four-section boom. Maximum tip height is 17,98 m (59 ft). (no jib option available). 4,88 m - 5 m ( ft -49 ft) four-section boom Model 66H Equipped with a 7,32 m - 18,3 m (24 ft - 6 ft) three-section boom. Maximum tip height is 21,3 m (7 ft) (no jib option available). 7,2 m - 18,3 m (24 ft- 6 ft) three-section boom Model 671H Equipped with a 8,23 m - 21,64 m (27 ft - 71 ft) three-section boom. This model can be equipped with a 7,62 m - 13,72 m ( ft - ft) two-section jib. Maximum tip height with 13,72 m ( ft) jib is 38, m (1 ft). 8,23 m - 21,64 m (27 ft - 71 ft) three-section boom 6FJM 7,62 m - 13,72 m ( ft - ft) two-section jib Model 68H Equipped with a 7,32 m - 24,38 m (24 ft - 8 ft) four-section boom. Maximum tip height is 27,44 m (9 ft) (no jib option available). 7,32 m - 24,38 m (24 ft- 8 ft) four-section boom Model 69H Equipped with a 8,23 m - 27,43 m (27 ft - 9 ft) four-section boom. This model can be equipped with a 7,62 m - 13,72 m ( ft - ft) two section jib. Maximum tip height with 13,72 m ( ft) jib is 43,95 m (144 ft). 8,23 m - 27,43 m (27 ft - 9 ft) four-section boom 6FJM 7,62 m - 13,72 m ( ft - ft) two-section jib Note: Maximum tip is measured with outriggers/stabilizers fully extended. 6

7 Capacities 6H Winch Data All winch pulls and speeds in this chart are shown on the fourth layer Winch line pulls would increase on the first and second layers Winch line pulls may be limited by the winch capacity or the ANSI 5 to 1 cable safety factor, shown below this chart Hook blocks are rated at maximum capacity for the block. Do not exceed rated cable pull with any block. 1 part line 2 part line 3 part line 4 part line 5 part line 6 part line Winch Cable supplied Minimum breaking strength Max. pull Max. pull Max. pull Max. pull Max. pull Max. pull Standard planetary winch 9/" diameter rotation resistant kg (38,5 lb) 3493 kg (77 lb) 6985 kg (15,4 lb) kg (23,1 lb) kg (3,8 lb) kg (38,5 lb) kg (4, lb) Layer Winch pull Winch speed OS winch speed Rope capacity kg lb mpm fpm mpm fpm m ft , NOTE: All ratings based on 128,7 LPM at 22,75 MPa (34 GPM at 33 psi). urst of speed maximum pull = 1361 kg (3 lb) Winch are drum pull Allowable cable pull With standard rotation resistant rope 4627 kg (1,2 lb) 3493 kg (77 lb) lock Type Rating Weight Downhaul Weight 6,4 t (7 USt) 78 kg (171 lb) 1 Sheave lock 11,3 t (12.5 USt) 91 kg (2 lb) 2 Sheave lock 2 t (22 USt) 1 kg (5 lb) National Crane Series 6H 7

8 Capacities 638H: 11,58 m (38 ft) boom with full span outriggers, no jib Other Series 6H load rating charts are available. National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. LENGTH IN FEET A 2 4 RADIUS IN FEET HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factoryapproved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. Load chart RADIUS (FT) (DEG) FT (L) (DEG) A 24 FT (L) (DEG) 31 FT (L) (DEG) 38 FT (L) , 36,15 3,,6 21,9,75 1, , 24,3 2,9 18,15,2 14,2 12, ,5 23, 2,15 17,8 15,8 14,15 12,9 1, ,75 22,2 19,2 17,5 15,2 13,75 12, * Shaded areas are structurally limited capacities. 8 THIS CHART IS ONLY A GUIDE AND SHOULD NOT E USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

9 Capacities 649H: 15 m (49 ft) boom with full span outriggers, no jib Other Series 6H load rating charts are available. National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. LENGTH IN FEET C A RADIUS IN FEET HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factory-approved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. Load chart RADIUS (ft) FT 4, 29,6 24,7 2,4 13, ,95 * Shaded areas are structurally limited capacities. A FT 38,1 27,4 23,2 2,2 17,75 15,75 12, FT 26,2 22,2 19, 17, 15,2 12, C 41 FT,3 21,3 18,,3 14, 12, FT 19,5 17,5 15, 13,75 11, National Crane 6H THIS CHART IS ONLY A GUIDE AND SHOULD NOT E USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 9

10 Capacities 66H: 18,3 m (6 ft) boom with full span outriggers, no jib Other Series 6H load rating charts are available. National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. LENGTH IN FEET RADIUS IN FEET A C HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factoryapproved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. RADIUS (ft) FT * Shaded areas are structurally limited capacities. 4, 27,2 22,8 19, 17,15 15,15 11, Load chart A 33 FT,8 21,6 18,7,4 14,6 11, FT, 2,7 17,8 15,75 14,5 11, C 51 FT 2,4 17,4 15, 13,6 11, FT 17,15 14,95 13,2 1, THIS CHART IS ONLY A GUIDE AND SHOULD NOT E USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

11 Capacities 671H: 21,6 m (71 ft) boom with 13,7 m ( ft) jib and full span outriggers Other Series 6H load rating charts are available. National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. 2 nd Jib ' 1 st Jib ' LENGTH IN FEET D C A 28 Do not 2 extend 1 jib into this -1 area HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factory-approved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. RADIUS IN FEET NOTE: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. Do not exceed rated jib capacities at any reduced boom lengths. Load chart RADIUS (ft) FT 4,, 21, 17,9, 14,9 11, A FT 44 FT * Shaded areas are structurally limited capacities. 24,75 21, 17,95 15, 13,7 11, , 2, 17, 15,5 13, 1, C 53 FT 2,1 17,15 15, 13, 1, D 62 FT, 14,4 12,75 1, FT 12, 12, 1, ft ft JI FULL SPAN RATED LOADS ft 44 ft JI JI RADIUS (ft) National Crane 6H THIS CHART IS ONLY A GUIDE AND SHOULD NOT E USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 11

12 Capacities 68H: 23,4 m (8 ft) boom with full span outriggers, no jib Other Series 6H load rating charts are available. National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. LENGTH IN FEET A D C RADIUS IN FEET HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factory-approved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. RADIUS (ft) FT * Shaded areas are structurally limited capacities. 4, 27,1 22,4 19,5 17,1 14,75 11, A 36 FT,4 21,4 18,, 14,2 11, Load chart 47 FT 2,6 17, 15,3 13, 11, C 58 FT 17,5 14,75 13,5 1, D 69 FT 12,15 1, FT THIS CHART IS ONLY A GUIDE AND SHOULD NOT E USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

13 Capacities 69H: 27,4 m (9 ft) boom with 13,7 m ( ft) jib and full span outriggers Other Series 6H load rating charts are available. National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. 2nd Jib ' LENGTH IN FEET 1st Jib ' RADIUS IN FEET Do not extend jib into 8 6 this 2 area A C D HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii. Load ratings shown on the appropriate charts are maximum allowable loads with the crane mounted on a factoryapproved truck and all outriggers at either full span or at mid span range and set on a firm level surface so that the crane is level and all tires are suspended. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. NOTE: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. Do not exceed rated jib capacities at any reduced boom lengths. Load chart RADIUS (ft) FT 4,,75 21,4 18,,4 14,75 11, A 41 FT 2,95 17,75 15, 13,3 1, FT 17, 15, 13,2 1, C 66 FT 14, 12, D 78 FT FT ft ft JI FULL SPAN RATED LOADS ft ft JI JI RADIUS (ft) * Shaded areas are structurally limited capacities National Crane 6H THIS CHART IS ONLY A GUIDE AND SHOULD NOT E USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 13

14 Dimensions Standard mount Series G H Dry weight* 638H 123 cm (48.43 in) 1 cm (.81 in) 631 kg (13,891 lb) w/oil weight* 6632 kg (14,622 lb) H style rear stabilizers with oil weight 672 kg (1481 lb) 649H 141 cm (.32 in) 123 cm (48.38 in) 9 kg (14,529 lb) 6937 kg ( lb) 66H 8 cm (66.9 in) 128 cm (5. in) 6857 kg (15,1 lb) 7218 kg (15,912 lb) 95.5" 671H 176 cm (69.29 in) 134 cm (52.92 in) 71 kg (15,8 lb) 77 kg (,9 lb) 68H 5 cm (64.93 in) 142 cm (.95 in) 73 kg (,236 lb) 7752 kg (17,9 lb) 69H 197 cm (77. in) 153 cm (6.8 in) 87 kg (17,3 lb) 8398 kg (18,515 lb) * AOVE WEIGHTS DO NOT INCLUDE RESERVOIR, RSOD, JI, PTO, PUMP, ED ** WEIGHT INCLUDES, WINCH, ROPE, TURRET, LIFT CYLINDER, FRAME, CONTROLS, OUTRIGGERS, PLATFORMS, TORQUE OX, REST, UMPER, DOWNHAUL WEIGHT Top of truck frame rail 19 (49.56") 641 (.") 2248 (88.5") Retracted 348 (12.") Mid span R 1152 (.34") tail swing 5283 (28.") Extended STANDARD MOUNT 638H 5 (' - 7") Retracted (38' - ") Extended 671H 847 (27' - 7") Retracted (71' - ") Extended 533 G (21.") 649H 4978 (' - 4") Retracted 14 9 (49' - ") Extended 68H 7315 (24' - ") Retracted (8' - ") Extended 66H 7264 (23' - 1") Retracted (6' - 2") Extended 69H 8484 (27' - 1") Retracted (9' - ") Extended (143.97") 315 (118.72") 2394 (94.") 1848 (72.75") CG H 9.95 UNITS IN INCHES UNLESS SPECIFIED Top of truck frame rail Rotation 14

15 Accessories Radio Remote Controls Eliminate the handling and maintenance concerns that accompany cabled remotes. Operate to a range of about 76 m ( ft), varying with conditions. Heavy-duty Personnel asket 544 kg (12 lb) capacity steel basket with safety loops for two passengers. Gravity leveling 183 cm x 17 cm (72 in x 42 in) platform. Fast attachment and secure locking systems. Load chart must show 143 kg (23 lb) minimum to operate this accessory. R4R SA-1 SA-R1 (provides rotation) Duty Cycle Package urst of speed winch (OS) control option, hydraulic oil cooler (OC), and self-contained radiator system with electric fan. Single Front Outrigger Center front stabilizer with a in vertical stroke ulkhead-steel oom mounted hose reel With control valve and hydraulic hoses Spanish-Language Danger Decals, DCPKG SFO HSD CRH SDD Spanish Operators Manuals SOM National Crane 6H 15

16 Manitowoc Cranes Regional headquarters Americas Manitowoc, Wisconsin, USA Tel: Fax: Shady Grove, Pennsylvania, USA Tel: Fax: Europe, Middle East, Africa Dardilly, France Tel: +33 () Fax: +33 () China Shanghai, China Tel: Fax: Greater Asia-Pacific Singapore Tel: Fax: Regional offices Americas razil Alphaville Mexico Monterrey Chile Santiago Europe, Middle East, Africa France audemont Cergy Decines Germany Langenfeld Italy Lainate Netherlands reda Poland Warsaw Portugal altar Russia Moscow South Africa Johannesburg U.A.E. Dubai U.K. uckingham China eijing Chengdu Guangzhou Xian Greater Asia-Pacific Australia risbane Melbourne Sydney India Chennai Delhi Hyderabad Pune Korea Seoul Philippines Makati City Singapore Factories razil Passo Fundo China TaiAn Zhangjiagang France Charlieu Moulins Germany Wilhelmshaven India Pune Italy Niella Tanaro Portugal altar Fânzeres USA Manitowoc Port Washington Shady Grove This document is non-contractual. Constant improvement and engineering progress 214 Manitowoc Form No. 6H PG Part No. 6H / 2M / 314