RESIDENTIAL GRADE

Transcription

1 1 RESIDENTIAL GRADE

2 LEDH-310ICA 3.5 Low Voltage LED IC Rated New Construction Recessed Housing MR16 LED Bulb 4-13/16 (123mm) DESCRIPTION 3-3/4 (95mm) Ceiling Cut-out : 3-7/8 Lamp, Max, Watt. : 12.2W The LEDH-310ICA is designed for insulated ceilings and can be in direct contact with insulation material. The LEDH-310ICA offers a wide choice of trim types including reflector, lensed and wall wash trims. This AIR-TIGHT housing design prevents airflow through the ceiling, helping save on heating and cooling costs. Housing Galvanized steel housing painted white 5-1/2 height allows use in 2 X6 joist construction. Housing adjusts for ceilings up to 1-1/4 thick. Junction Box Listed for through branch circuit wiring. (Max.8 No 12 AWG 90 C branch circuit conductors.(4 in, 4 out) (5)1/2" knockouts with true pry-out slots and (4) knockouts with Romex cable clamp. Ground wire provided on J-box. Recommended Dimmer Lutron : D i v a(dv-600p) Skylark( S -600P) Ariadni(AY-600P) Consult tech. service or factory for additional dimmers Mounting Frame Galvanized steel construction. 8 L X 5-1/2 W Transformer 120V magnetic transformer steps line voltage down to 12V operating voltage for lamps up to 15W Max. Available 277V-12V transformer. Socket GU5.3 Ceramic Bi-Pin Socket. Lamp LED MR16 12V 12.2W Max. (Not Included: see "Cree COB LED at end of section for Specs and ordering information) Bar Hangers Maximum extension of 24 allows for extra distance between joists. Housing can be positioned at any point within 24 joist span. Snap-off segments allow tool-free shortening for 12 joists. Bar hangers may be repositioned 90 degrees. Integral T-bar clips snaps onto T-bars and no additional clips are required. Optional Quick Connect Push-in Wire Connectors. Three Quick Connectors Pre-installed push-in wire connectors for fast and easy wiring. Listing cetlus Damp Location. 02/02/17

3 LEDH-310ICAR 3.5 Low Voltage LED IC Rated Remodel Recessed Housing MR16 LED Bulb 14-5/16 (363mm) 4-13/16 (123mm) DESCRIPTION 3-3/5 (92mm) Ceiling Cut-out : 3-7/8 Lamp, Max, Watt. : 12.2W The LEDH-310ICAR is designed for insulated ceilings and can be in direct contact with insulation material. The LEDH-310ICAR offers a wide choice of trim types including reflector, lensed and wall wash trims. This AIR-TIGHT housing design prevents airflow through the ceiling, helping save on heating and cooling costs. Housing Galvanized steel housing painted white 5-1/2 height allows use in 2 X6 joist construction. Housing adjusts for ceilings up to 1-1/2 thick. Junction Box Listed for through branch circuit wiring. (Max.8 No 12 AWG 90 C branch circuit conductors.(4 in, 4 out) (5)1/2" knockouts with true pry-out slots and (4) knockouts with Romex cable clamp. Ground wire provided on J-box. Recommended Dimmer Lutron : D i v a(dv-600p) Skylark( S -600P) Ariadni(AY-600P) Consult tech. service or factory for additional dimmers Transformer 120V magnetic transformer steps line voltage down to 12V operating voltage for lamps up to 15W Max. Available 277V-12V transformer. Socket GU5.3 Ceramic Bi-Pin Socket. Lamp LED MR16 12V 12.2W Max. (Not Included: see "Cree COB LED at end of section for Specs and ordering information) Remoled Clips 4 remodel clips secure housing and accommodates 1/2 and 5/8 ceiling materials. Optional Quick Connect Push-in Wire Connectors. Three Quick Connectors Pre-installed push-in wire connectors for fast and easy wiring. Listing cetlus Damp Location.

4 Designs/Trims For LEDH-310ICA, LEDH-310ICAR LT-350 Shower Frosted Flat Lens Die-Cast Construction O.D : 4-5/16" MR16 LED Bulb LT-350WH LT-350CH LT-350SN LT-351 Shower Convex Shape Lens Die-Cast Construction O.D : 4-5/16" LT-351WH LT-351CH LT-351MO LT-352 Tapered Glass Diffuser Die-Cast Construction O.D : 4-5/16" LT-352WH LT-352WH-B LT-352BK LT-354 Adjustable Reflector Die-Cast Construction O.D : 4-5/16" LT-354CL LT-354CL-CH LT-354WH LT-355 Adjustable Baffle Die-Cast Construction O.D : 4-5/16" LT-355WH LT-355BK LT-355BK-CH LT-358 Pin Spot w/ Baffle Die-Cast Construction O.D : 4-5/16" LT-358BK LT-358BK-SN LT-358BK-MO LT-359 Pin Spot w/reflector Die-Cast Construction O.D : 4-5/16" LT-359CL LT-359BK-SN LT-359BK-MO LT-360 Slotted Wall Wash Die-Cast Construction O.D : 4-5/16" LT-360WH LT-360SN LT-360MO

5 Designs/Trims For LEDH-310ICA, LEDH-310ICAR LT-361 Adjustable Wall Wash w/baffle Die-Cast Construction O.D : 4-5/16" MR16 LED Bulb LT-361WH LT-361PB LT-361MO LT-362 Dropped Clear Etched Lens Die-Cast Construction O.D : 4-5/16" LT-362WH LT-362BK LT-362SN LT-364 Gimbal w/baffle Die-Cast Construction O.D : 4-5/16" LT-364WH LT-364BK-SN LT-364BK-MO Ordering Information Model LEDH-310ICA = 3.5, IC New Construction LEDH-310ICAR = 3.5, IC Remodel Example : LEDH-310ICA277-Q Voltage Blank = 120V to 12V 277 = 277V to 12V -Options -E = Electronic Transformer -Q = Quick Wire Connectors Design / Trim* LT-350WH = White LT-350CH = Chrome LT-350SN = Satin Nickel LT-351WH = White LT-351CH = Chrome LT-351MO = Mocha LT-352WH = White LT-352WH-B = White-Blue LT-352BK = Black LT-354CL = Clear LT-354CL-CH = Clear-Chrome LT-354WH = White LT-350WH LT-355WH = White LT-355BK = Black LT-355BK-CH = Black-Chrome LT-358BK = Black LT-358BK-SN = Black-Satin Nickel LT-358BK-MO = Black-Mocha LT-359CL = Clear LT-359BK-SN = Black-Satin Nickel LT-359BK-MO = Black-Mocha LT-360WH = White LT-360SN = Satin Nickel LT-360MO = Mocha LT-361WH = White LT-361PB = Polished Brass LT-361MO = Mocha LT-362WH = White LT-362BK = Black LT-362SN = Satin Nickel LT-364WH = White LT-364BK-SN = Black-Satin Nickel LT-364BK-MO = Black-Mocha * Consult factory for other Color Temperatures and Finishes

6 LEDH-410ICA 4 Low Voltage LED IC Rated New Construction Recessed Housing 13-1/4 will extand to 25 MR16 LED Bulb 5-1/2 (140mm) DESCRIPTION 4-5/16 (109mm) Ceiling Cut-out : 4-3/8 Lamp, Max, Watt. : 12.2W The LEDH-410ICA is designed for insulated ceilings and can be in direct contact with insulation material. The LEDH-410ICA offers a wide choice of trim types including reflector, lensed and wall wash trims. This AIR-TIGHT housing design prevents airflow through the ceiling, helping save on heating and cooling costs. Housing Single wall aluminum housing. 5-1/2 height allows use in 2 X6 joist construction. Housing adjusts for ceilings up to 1-1/4 thick. Junction Box Listed for through branch circuit wiring. (Max.8 No 12 AWG 90 C branch circuit conductors.(4 in, 4 out) (5)1/2" knockouts with true pry-out slots and (4) knockouts with Romex cable clamp. Ground wire provided on J-box. Recommended Dimmer Lutron : D i v a(dv-600p) Skylark( S -600P) Ariadni(AY-600P) Consult tech. service or factory for additional dimmers Mounting Frame Galvanized steel construction. 8 L X 5-1/2 W Transformer 120V magnetic transformer steps line voltage down to 12V operating voltage for lamps up to 15W Max. Available 277V-12V transformer. Socket GU5.3 Ceramic Bi-Pin Socket. Lamp LED MR16 12V 12.2W Max. (Not Included: see "Cree COB LED at end of section for Specs and ordering information) Bar Hangers Maximum extension of 24 allows for extra distance between joists. Housing can be positioned at any point within 24 joist span. Snap-off segments allow tool-free shortening for 12 joists. Bar hangers may be repositioned 90 degrees. Integral T-bar clips snaps onto T-bars and no additional clips are required. Optional Quick Connect Push-in Wire Connectors. Three Quick Connectors Pre-installed push-in wire connectors for fast and easy wiring. Listing cetlus Damp Location.

7 LEDH-410ICAR 4 Low Voltage LED IC Rated Remodel Recessed Housing MR16 LED Bulb 14-3/8 (365.2mm) 5-5/8 (142.3mm) DESCRIPTION 4-1/8 (105mm) Ceiling Cut-out : 4-3/8 Lamp, Max, Watt. : 12.2W The LEDH-410ICAR is designed for insulated ceilings and can be in direct contact with insulation material. The LEDH-410ICAR offers a wide choice of trim types including reflector, lensed and wall wash trims. This AIR-TIGHT housing design prevents airflow through the ceiling, helping save on heating and cooling costs. Housing Single wall aluminum housing. 5-1/2 height allows use in 2 X6 joist construction. Housing adjusts for ceilings up to 1-1/2 thick. Junction Box Listed for through branch circuit wiring. (Max.8 No 12 AWG 90 C branch circuit conductors.(4 in, 4 out) (5)1/2" knockouts with true pry-out slots and (4) knockouts with Romex cable clamp. Ground wire provided on J-box. Recommended Dimmer Lutron : D i v a(dv-600p) Skylark( S -600P) Ariadni(AY-600P) Consult tech. service or factory for additional dimmers Transformer 120V magnetic transformer steps line voltage down to 12V operating voltage for lamps up to 15W Max. Available 277V-12V transformer. Socket GU5.3 Ceramic Bi-Pin Socket. Lamp LED MR16 12V 12.2W Max. (Not Included: see "Cree COB LED at end of section for Specs and ordering information) Remoled Clips 3 remodel clips secure housing and accommodates 1/2 and 5/8 ceiling materials. Optional Quick Connect Push-in Wire Connectors. Three Quick Connectors Pre-installed push-in wire connectors for fast and easy wiring. Listing cetlus Damp Location.

8 Designs/Trims For LEDH-410ICA, LEDH-410ICAR LT-42 Adjustable Baffle White Metal Trim Ring O.D : 4-7/8" MR16 LED Bulb LT-42-WH LT-42-BK LT-42-CH LT-44 Adjustable Reflector White Metal Trim Ring O.D : 4-7/8" LT-44-CL LT-44-GD LT-44BK-MO LT-43 Eyeball White Metal Trim Ring O.D : 4-7/8" LT-43WH LT-43PB LT-43MO LT-47 Retractable Wall Wash White Metal Trim Ring O.D : 4-7/8" LT-47WH LT-47CH LT-47MO LT-48 Adjustable Wall Wash White Metal Trim Ring O.D : 4-7/8" LT-48WH LT-48SN LT-48AN LT-49 Pin Hole w/ Baffle White Metal Trim Ring O.D : 4-7/8" LT-49WH LT-49SN LT-49MO LT-410 Slotted Wall Wash w/ Baffle White Metal Trim Ring O.D : 4-7/8" LT-410WH LT-410BK LT-410BK-MO LT-411 Gimbal White Metal Trim Ring O.D : 4-7/8" LT-411WH LT-411SN LT-411MO

9 Designs/Trims For LEDH-410ICA, LEDH-410ICAR LT-416 Eyeball w/ Baffle White Metal Trim Ring O.D : 4-7/8" MR16 LED Bulb LT-416WH LT-416BK LT-416BK-PB LT-418 Pin Spot White Metal Trim Ring O.D : 4-7/8" LT-418WH LT-418BK LT-418BK-SN LT-46 Wall Wash White Metal Trim Ring O.D : 4-7/8" LT-46WH LT-417 Wall Wash w/ Baffle White Metal Trim Ring O.D : 4-7/8" LT-417WH LT-417BK Ordering Information Model Voltage -Options Design / Trim* LEDH-410ICA = 4, IC New Construction LEDH-410ICAR = 4, IC Remodel Example : LEDH-410ICA-E-Q Blank = 120V to 12V 277 = 277V to 12V -E = Electronic Transformer -Q = Quick Wire Connectors LT-42WH = White LT-42BK = Black LT-42CH = Chrome LT-43WH = White LT-43PB = Polished Brass LT-43MO = Mocha LT-44CL = Clear LT-44GD = Gold LT-44BK-MO = Black-Mocha LT-47WH = White LT-47CH = Chrome LT-47MO = Mocha LT-42WH LT-48WH = White LT-48SN = Satin Nickel LT-48AN = Antique Nickel LT-49WH = White LT-49SN = Satin Nickel LT-49MO = Mocha LT-410WH = White LT-410BK = Black LT-410BK-MO = Black-Mocha LT-411WH = White LT-411SN = Satin Nickel LT-411MO = Mocha LT-416WH = White LT-416BK = Black LT-416BK-PB = Black-Polished Brass LT-418WH = White LT-418BK = Black LT-418BK-SN = Black-Satin Nickel LT-46WH = White LT-417WH = White LT-417BK = Black * Consult factory for other Color Temperatures and Finishes

10 CREE COB LED Designed as a direct retrofit to most MR16 lighting fixtures 6W LED lamp, for replacement of 35-50W MR16 lamps High efficacy (~67-70lm/W) High quality light with a color rendering index of 80CRI Suitable for use in totally enclosed luminaires Product Offering Lamp Energy Used Brightness CCT Beam Angles E9564F-M W 400 lm 2700K 25 E9564F-M W 400 lm 2700K 40 E9564F-M W 420 lm 3000K 25 E9564F-M W 420 lm 3000K 40 Features and Benefits 6W GU5.3 base LED lamp Available beam angles : 25 and 40 Input voltage : 12VAC or DC Available in two different color temperatures: 2700K warm 3000K warm white Rated lifetime : 40,000 hours UV,NIR and Mercury free 3years Lum-Tech Lighting warranty For different color temperatures and beam angles, contact factory for availability and order quantities Specifications Average lifetime Starting time Switching cycles (30s on, 30s off) Warm up time Working Conditions Tc temperature max Mercury 40,000 hr 20 ms 1,000,000 None (Instant On) -20~ mg LED Brand Length Diameter Weight Input voltage Nominal current (12VAC/ 60HZ) Power Power factor CREE 46.5mm 50mm 52g 120VAC 1.0A max 6W >0.75

11 LEDH-3110ICA 120VAC LED DoB 3.5 IC/AIR-TIGHT Recessed down light for new construction LEDH VAC LED DoB 3.5 NON-IC Recessed down light for new construction 3.5 LED 8 (203mm) 5-1/2 (140mm) DESCRIPTION 13-1/4" Will Expand To 25" 4-3/8 (110mm) Height : 5-1/2 Ceiling Cut-out : 3-7/8 The LEDH-3110ICA and LEDH-3110 are IC and Non-IC type 3.5 aperture down lights. The LED DoB Module is designed to maintain 70% average lumen output at 50,000hr or 5 years life. Non-IC rated housing must be kept 3 away from insulation. IC rated housing is suitable for direct contact with insulation. Equivalent light output to a 35W MR16 lamp while using only 9 watts of power. Suitable for Wet Location. Housing Galvanized steel housing. Housing is adjustable for thickness up to 1-1/4 Junction Box Listed for through branch circuit wiring. (Max.8 No 12 AWG 90 C branch circuit conductors.) (5)1/2" knockouts with pry-out slots and (4) knockouts with Romex cable clamps. Ground wire provided on J-box. Bar Hangers 24 Bar Hangers provide stability and support on joists and T-Bar Grid ceilings. Housing can be positioned at any point within 24 joist spacing. Score lines allow easy bend & snap-off shortening for 12 joist spacing. Trims Standard offerings with baffle trims in painted white or black plus haze clear reflectors. See Trims spec sheet for full offerings and ordering information. Optics Lens: Fine, textured surface of tempered glass provides high lumen transmission and diffusion for even illumination. LED Engine Aluminum Heat Sink computer designed in conjunction with an aluminum clad PC board for superior thermal management. Lumen Maintenance: L70, 70% lumens of initial 50,000 hours. Electrical Connection: LED DoB module is replaceable via an on-board quick disconnect terminal (No tools required). Electrical Connection; Provided with quick connector between LED module and housing for easy plug and play installation. 120VAC Direct DoB circuit on Board with customized IC chip % triac dimmable with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for a maximum 45 fixtures per run on a 600W max load per dimmer switch and a max. 23 fixtures per a dimmer switch for a 300W load. Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Wet Location ENERGY STAR California Title 24 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 9 W Lumen (+/-5%) 555 lm Efficacy (LPW) 61.7 lm/w Beam Angle 43.7 CRI (Typical) 80 CCT (Color +/-5%) 2700K, 3000K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELVSeries RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers 02/02/17

12 LEDH-3110ICAR 120VAC LED DoB 3.5 LED IC/AIR-TIGHT Recessed down light for Remodeling LEDH-3110R 120VAC LED DoB 3.5 LED NON-IC Recessed down light for Remodeling 3.5 LED 5-5/16 (138.8mm) DESCRIPTION 3-7/8 (98.5mm) 16-3/4 (423mm) Height : 5-5/16 Ceiling Cut-out : 3-7/8 LEDH-3110ICAR and LEDH-3110R are IC and Non-IC type 3.5 aperture down lights. The LED DoB 120VAC Direct Module is 9W and is designed to maintain 70% average lumen output at 50,000hr or 5 years life. Non-IC rated housing must be kept 3 away from insulation. IC rated housings are suitable for direct contact with insulation. Equivalent light output to a 35W MR16 lamp while only using 9 watts of power. Suitable for Wet Locations. Housing Galvanized steel housing painted Black. Junction Box Listed for through branch circuit wiring. (Max.8 No 12 AWG 90 C branch circuit conductors.) (5)1/2" knockouts with pry-out slots and (4) knockouts with Romex cable clamps. Ground wire provided on J-box. Remodel Clips 3 remodel clips secure housing and accommodates 1/2" and 5/8" thick ceilings. Trims Standard offerings with baffle trims in painted white or black plus haze clear reflectors. See Trims spec sheet for full offerings and ordering information. Optics Glass Lens: Fine, textured surface of tempered glass provides high lumen transmission and diffusion for even illumination. LED Engine Aluminum Heat Sink computer designed in conjunction with an aluminum clad PC board for superior thermal management. Lumen Maintenance: L70, 70% lumens of initial 50,000 hours. Electrical Connection: LED DoB module is replaceable via an on-board quick disconnect terminal (No tools required). Electrical Connection; Provided with quick connector between LED module and housing for easy plug and play installation. 120VAC Direct DoB Driver on Board with customized IC chip % triac dimmable with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for a maximum 45 fixtures per run on a 600W max load per dimmer switch and a max. 23 fixtures per a dimmer switch for a 300W load. Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Wet Location ENERGY STAR California Title 24 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 9 W Lumen (+/-5%) 555 lm Efficacy (LPW) 61.7 lm/w Beam Angle 43.7 CRI (Typical) 80 CCT (Color +/-5%) 2700K, 3000K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELVSeries RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers 02/02/17

13 LEDT-C34 Reflector -HC = Haze Clear -PR = Pewter -CP = Champagne -WH = White Painted O.D : 4-5/16" 3.5 LED LEDT-C34-WH-WH LEDT-C32 Baffle -WH = White -BK = Black O.D : 4-5/16" LEDT-C32-WH-WH PHOTOMETRIC REPORT * Contact Factory for IES File Polar Candela Distribution CD: VA: ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width fc 1.6 ft 47.1 fc 3.2 ft 21.0 fc 4.8 ft 11.8 fc 6.4 ft 7.5 fc 8.0 ft 5.2 fc 9.6 ft Beam Spread: 43.7 [LEDH-3110ICA-840DOB+LEDT-C34-WH] Ordering Information Model -Watts -CRI Color Temp.* Driver Trim -Finishes* -Trim Ring Finishes* LEDH-3110 = 3.5 LED NON-IC LEDH-3110ICA = 3.5 LED IC LEDH-3110R = 3.5 LED NON-IC LEDH-3110ICAR = 3.5 LED IC -9 = 9W -8 = 80 CRI 27 = 2700K 30 = 3000K 40 = 4000K DOB = 120V Direct Driver on Board (dimmable with most Line or Low Voltage Dimmers) LEDT-C34 = Reflector LEDT-C32 = Baffle Reflector: -HC = Haze Clear -PR = Pewter -CP = Champane -WH = White Painted Baffle: -WH = White -BK = Black WH = White BK = Black SN = Satin Nickel AN = Antique Nickel AC = Antique Copper MO = Mocha CA = Cappuccino CH = Chrome UN = Natural Steel PB = Polished Brass Example : LEDH-3110ICA-9-830DOB LEDT-C34-HC-WH * Consult factory for other Color Temperatures and Finishes

14 LEDH-680IC 6 IC LED Housing For Sloped Ceiling 6 LED 5-1/16 (129.3mm) 7-13/16 (198.5mm) 12-1/16 (305.7mm) 7-5/8 (193.8mm) 13-1/4 Will Expand To 25 DESCRIPTION Ceiling Cut-out : 7-1/16 X 6-7/8 Designed for sloped ceiling installations for ceilings from 2/12 to 6/12 pitch. The lamp aiming mechanism allowing to be aimed straight down regardless of ceiling pitch. The LEDH-680IC is designed for insulated ceilings and can be in direct contact with ceiling insulation. Junction Box Listed for through branch circuit wiring.(max.8 No 12 AWG 90 C branch circuit conductors.) (5)1/2" knockouts with true pry-out slots and (4) knockouts with Romex cable clamp. Ground wire provided on J-box. Provided listed quick connectors for easy snap-in wires. (Optional) Bar Hangers 24 Bar Hangers provide stability and support on joists and T-Bar Grid ceilings. Housing can be positioned at any point within 24 joist span. Score lines allow tooless shortening for 12 joists. Heat Sink Aluminum extruded Heat sink designed to facilitate heat dissipation to reduce LED junction temperature for maintaining constant light output, color and life of solid state components. Trims Available with baffle trims in white or black painted and haze clear reflectors. See Trims spec sheet for selection or ordering information. LED Engine Heat sink designed by computer simulation and aluminum board for low heat operation. Lumen Maintenance: L70/50, 70% lumens/50,000 hours Module construction includes LED, heat sink and lens. LED POWER SUPPLY Include 120~277V input high efficacy driver with the capability to dim using a Triac 120V low voltage electronic dimmer switch. Driver feature power factor >.90, THD <20% and has integral thermal protection to sense over temperature or internal failure. Driver mounts externally to the module, allowing future replacement, if needed. Consult with factory for optional 0~10V analog dimmable driver. SPECIFICATIONS LED Quantity Input Voltage 1EA (COB) 120V~277V AC Wattage (+ /-5%) Lumen (+ /-5%) Efficacy(LPW) 14W W 1, Color (+ /-5%) CRI (Typical) Beam Angle Dimming Lamp Life Environment 2700K, 3000K, 4000K 80 Avail. Triac (Standard), 0-10V 50,000hr Indoor 120V Approved Dimmers * Lutron: NovaT(Ntelv300&600) Diva (Dvelv-300P&303P) * Leviton: Acenti: Ate06-1Lw * Leviton Trimatron #705W(incandescent) Consult tech. service or factory for additional dimmers Warranty 50,000hr of lamp life. Listing ETL Listed. 07/06/17 LUM-TECH LIGHTING

15 TRIMS & PHOTOMETRIC REPORT For LEDH-680IC 6 LED TRIMS LEDT-S65 Slope Reflector haze clear reflector (-HC) pewter reflector (-PR) champane reflector (-CP) white painted reflector (-WH) O.D : 4-7/8" LEDT-S65-HC LEDT-S65-CP LEDT-S62 Slope Baffle white baffle (-WH) black baffle (-BK) O.D : 4-7/8" LEDT-S62-WH LEDT-S62-BK Note. Standard white plastic trim ring. Consult with factory for optional trim ring finish. PHOTOMETRIC REPORT * Contact Factory for IES File Polar Polar Candela Distribution CD: VA: ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at at a a Distance Center Beam FC Beam Width fc ft fc ft fc ft fc ft fc ft fc ft Beam Spread: Polar Polar Candela Distribution CD: VA: ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width fc fc fc fc fc ft ft ft ft ft fc ft Beam Spread: [LEDH-680IC-14+LEDT-S65] [LEDH-680IC-23+LEDT-S65] ORDERING INFORMATION Housing LEDH-680IC Watts -14 : 14W -23 : 23W Example : LEDH-680IC-14W-30 Color Temp. -27 : 2700K -30 : 3000K -40 : 4000K Driver -UTD : 120~277V Triac Dimming (Standrd) -UZTD : 120~277V, 0-10V, Triac & ELV: 1-100% Dimming *Option -EM : Emergency battery backup Trim -LEDT-S65 -LEDT-S62 Reflector Finish Example : LEDT-S65-HC-WH -HC : haze clear -WH : white painted *Consult with factory for custom finishes Baffle Finish for LEDT-S62 -WH : White -BK : Black LUM-TECH LIGHTING

16 LEDH-NCR4ICA 120VAC LED DoB 4 Recessed Housing Down Light with Baffle Trim for IC type New Construction Applications 4 LED 7-3/8 (187mm) 3-1/2 (89mm) DESCRIPTION 7-1/8 (181mm) 4-15/16 (126mm) Ceiling Cut-out : 4-1/4 The LEDH-NCR4ICA down light is a 4, IC rated luminaire. The LED DoB 120VAC Direct engine has a 10W LED Module with integral triac dimming and can be controlled with most of leading and trailing edge dimmer switches. This easy to install fixture is designed for use in New Construction applications with insulated ceilings. Suitable for Wet Locations. LED Module & Trim Durable, one-piece die cast aluminum heat sink with integrated trim. Module construction includes LED, heat sink, lens and baffle trim. White painted finish standard. Lens High Impact Thermal plastic. Translucent, high lumen transmission and diffusing for even illumination. Sealed for Wet Locations and is ideal for shower rooms. Mounting Provided with a plaster frame (7-1/8 x 7-1/8 ) for new construction. HB-24 bar hangers are available as an accessory for new construction. Electrical Connection; J-box: - Installed on the top of fixture with (5)1/2 knockout. - Listed for through branch circuit wiring (max. 4, 12 AWG, 90 C rated wire). - Ground wire provided. 120VAC Direct DoB Driver on Board with customized IC chip % triac dimmable with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for a maximum 45 fixtures per run on a 600W max load per dimmer switch and a max. 23 fixtures per a dimmer switch for a 300W load. Accessories HB-24 hanger bars for use with housing plate for new construction applications Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Wet Location ENERGY STAR California Title 24 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 10 W Lumen (+/-5%) 625 lm Efficacy (LPW) 62.5 lm/w Beam Angle 90.5 CRI (Typical) 80, 90 CCT (Color +/-5%) 2700K, 3000K, 3500K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers

17 4 LED PHOTOMETRIC REPORT * Contact Factory for IES File Polar Candela Distribution CD: VA: ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width 80.8 fc 4.0 ft 20.2 fc 8.1 ft 9.0 fc 12.1 ft 5.1 fc 16.1 ft 3.2 fc 20.2 ft 2.2 fc 24.2 ft Beam Spread: 90.5 [LEDH-NCR4ICA(R)-830DOB] Ordering Information Model -CRI Color Temp.* Finish* Driver Accessories LEDH-NCR4ICA= 4, 10W Recessed IC, New Construction LEDH-NCR4ICAR = 4, 10W Recessed IC, Remodeling -8 = 80 CRI -9 = 90 CRI 27 = 2700K 30 = 3000K 40 = 4000K blank = White (Standard) DOB = 120V Direct Driver on Board (dimmable with most Line or Low Voltage Dimmers) HB-24 = 24 adjustable Hanger Bars (2) LEDH-NCR4ICA only Example : LEDH-NCR4ICA-830DOB * Consult factory for other Color Temperatures and Finishes

18 LEDH-NCR4ICAR 120VAC LED DoB 4 Recessed Housing with Baffle Trim for IC type Remodeling Applications 4 LED 4-15/16 (126mm) 3-1/2 (89mm) DESCRIPTION 4-15/16 (126mm) 4-15/16 (126mm) Ceiling Cut-out : 4-3/8 The LEDH-NCR4ICAR down light is a 4, IC rated luminaire. The LED DoB 120VAC Direct engine has a 10W LED Module with integral triac dimming and can be controlled with most of leading and trailing edge dimmer switches. This easy to install fixture is designed for remodeling pplications with insulated ceilings. Thermally protected, Suitable for Wet Locations. LED Module & Trim Durable, one-piece diecast aluminum heat sink with integrated trim. Module construction includes LED, heat sink, lens and baffle trim. (2) mounting clips on trim module for remodeling jobs. White painted finish standard. Lens High Impact Thermal plastic. Translucent, high lumen transmission and diffusing for even illumination. Sealed for Wet Locations and is ideal for shower rooms. Electrical Connection; J-box: - Installed on the top of fixture with (5)3/4 knockout. - Listed for through branch circuit wiring (max. 8, 12 AWG, 90 C wire). - Ground wire provided. 120VAC Direct DoB Driver on Board with customized IC chip % triac dimmable with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for a maximum 45 fixtures per run on a 600W max load per dimmer switch and a max. 23 fixtures per a dimmer switch for a 300W load. Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Wet Location ENERGY STAR California Title 24 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 10 W Lumen (+/-5%) 625 lm Efficacy (LPW) 62.5 lm/w Beam Angle 90.5 CRI (Typical) 80, 90 CCT (Color +/-5%) 2700K, 3000K, 3500K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers

19 4 LED PHOTOMETRIC REPORT * Contact Factory for IES File Polar Candela Distribution CD: VA: ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width 80.8 fc 4.0 ft 20.2 fc 8.1 ft 9.0 fc 12.1 ft 5.1 fc 16.1 ft 3.2 fc 20.2 ft 2.2 fc 24.2 ft Beam Spread: 90.5 [LEDH-NCR4ICA(R)-830DOB] Ordering Information Model -CRI Color Temp.* Finish* Driver Accessories LEDH-NCR4ICA= 4, 10W Recessed IC, New Construction LEDH-NCR4ICAR = 4, 10W Recessed IC, Remodeling -8 = 80 CRI -9 = 90 CRI 27 = 2700K 30 = 3000K 40 = 4000K blank = White (Standard) DOB = 120V Direct Driver on Board (dimmable with most Line or Low Voltage Dimmers) HB-24 = 24 adjustable Hanger Bars (2) LEDH-NCR4ICA only Example : LEDH-NCR4ICA-830DOB * Consult factory for other Color Temperatures and Finishes

20 LEDH-RT4SICA 4 IC and Airtight Shallow 2 hours Fire Rated LED Recessed Downlight 4 LED 120 Min. Fire Rated 4 (102mm) 4-1/4 (108mm) Housing Galvanized steel housing. Housing is adjustable for thickness up to 1-1/4 IC Fire Rated housing for 120 minutes. Junction Box Listed for through branch circuit wiring (Max.8 No 12 AWG, 90 C branch circuit conductors). (5) 1/2" knockouts with pry-out slots and (4) knockouts with Romex cable clamps. Ground wire provided on J-box. Bar Hangers 24 Bar Hangers provide stability and support on joists and T-Bar Grid ceilings. Housing can be positioned at any point within 24 joist spacing. Score lines allow easy bend & snap-off shortening for 12 joist spacing. Trims Standard offerings with baffle trims in painted white or black plus haze clear reflectors. See Trims spec sheet for full offerings and ordering information. Optics Lens: Fine, frosted surface of tempered glass provides high lumen transmission and diffusion for even illumination. LED Driver Universal, 120~277V input, high efficacy drivers with dimming capability with 0-10V Triac & ELV dimmer switches. Drivers feature power factor >.90, THD <20% with integral protection to sense over temperature or electrical issues. Driver mounts externally to the module to allow future replacement or upgrading if desired. Optional Lutron Hi-lume A-Series, LED drivers and EcoSystem 5-Series LED drivers are available. Lutron drivers provide flicker-free, smooth, continuous dimming down to 1% for Hi-lume and 5% for EcoSystem. (Contact factory for dimming system requirements) Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Damp and Wet Location California Title 24 Conforms to ASTM E283 Input Voltage Wattage (+/-5%) Lumen (+/-5%) Efficacy (LPW) Beam Angle CRI (Typical) CCT (Color +/-5%) Dimming LED Module Environment Height : 4-1/32 Housing Aperture : 4-3/16 Ceiling Cut-out : 4-1/4 SPECIFICATION VAC DOB CREE 10 W 11 W 820 lm 1014 lm 82 lm/w 92.2 lm/w , K, 3000K, 3500K, 4000K 0-10V, Triac, Lutron 1% & 5% 5 yr/50k hr Damp & Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers 09/19/18

21 LEDT-C44 Reflector -HC = Haze Clear -PR = Pewter -CP = Champagne -WH = White Painted O.D : 4-7/8" 4 LED LEDT-C44-WH-WH LEDT-C42 Baffle -WH = White -BK = Black O.D : 4-7/8" LEDT-C42-WH-WH LEDQT-42 Square Diecast Baffle -WH = White Frame : 4-3/4" x 4-3/4" LEDQT-42-WH LEDT-C411 Gimbal Adjustable -WH = White -BK = Black O.D : 4-7/8 LEDT-C411 LEDT-C450 Frosted Shower Lens -WH = White O.D : 4-7/8 LEDT-C450 Ordering Information Housing -Watts -Driver Trim -Watts -CRI Color* -Finishes* -Trim Ring Finish* LEDH-RT4SICA = 4 IC Air-tight Shallow -11 = 11W CREE * For Lutron & ERP Drivers ONLY -UZTD = ERP Triac, ELV & 0~10V Dimming -ULDE1 = Lutron 1% EcoSystem SoftOn/FadeToBlack -ULDE5 = Lutron 5% EcoSystem -LTE = 2-Wire 120V Lutron Dimming LEDT-C44 = Reflector LEDT-C42 = Baffle LEDQT-42 = Square Diecast Baffle LEDT-C411 = Gimbal Adjustable LEDT-C450 = Frosted Shower Lens -11 =11W CREE -10DOB =10W 120V Triac/ELV Dimming -10ZTDOB =10W 120V 0~10V Dimming -8 = 80-9 = = 2700K 30 = 3000K 35 = 3500K 40 = 4000K Reflector: -HC = Haze Clear -PR = Pewter -CP = Champagne -WH = White Painted Baffle: -WH = White -BK = Black -WH = White -BK = Black Example : LEDH-RT4SICA-11-UZTD LEDT-C HC-WH * Consult factory for other Color Temperatures and Finishes * Consult factory for 277V, ZTDOB LED module

22 LEDH-RT4ICA 4 IC/Airtight LED Recessed Down Light for New Construction 4 LED 6-3/8 (162mm) 5-9/16 (141mm) 8-1/8 (207mm) 4-1/4 (109mm) 4-1/8 (105mm) Housing Galvanized steel housing. Housing is adjustable for thickness up to 1-1/4 Junction Box Listed for through branch circuit wiring (Max.8 No 12 AWG, 90 C branch circuit conductors). (5) 1/2" knockouts with pry-out slots and (4) knockouts with Romex cable clamps. Ground wire provided on J-box. Bar Hangers 24 Bar Hangers provide stability and support on joists and T-Bar Grid ceilings. Housing can be positioned at any point within 24 joist spacing. Score lines allow easy bend & snap-off shortening for 12 joist spacing. Trims Standard offerings with baffle trims in painted white or black plus haze clear reflectors. See Trims spec sheet for full offerings and ordering information. Optics Lens: Fine, frosted surface of tempered glass provides high lumen transmission and diffusion for even illumination. LED Driver Universal, 120~277V input, high efficacy drivers with dimming capability with 0-10V Triac & ELV dimmer switches. Drivers feature power factor >.90, THD <20% with integral protection to sense over temperature or electrical issues. Driver mounts externally to the module to allow future replacement or upgrading if desired. Optional Lutron Hi-lume A-Series, LED drivers and EcoSystem 5-Series LED drivers are available. Lutron drivers provide flicker-free, smooth, continuous dimming down to 1% for Hi-lume and 5% for EcoSystem. (Contact factory for dimming system requirements) Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Damp and Wet Location ENERGY STAR California Title 24 Input Voltage Wattage (+/-5%) Lumen (+/-5%) Efficacy (LPW) Beam Angle CRI (Typical) CCT (Color +/-5%) Dimming LED Module Environment Height : 5-9/16 Housing Aperture : 4-1/4 Ceiling Cut-out : 4-3/8 SPECIFICATION VAC DOB CREE 10 W 11 W 820 lm 1014 lm 82 lm/w 92.2 lm/w , K, 3000K, 3500K, 4000K 0-10V, Triac, Lutron 1% & 5% 5 yr/50k hr Damp & Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers 09/19/18

23 LEDH-RT4ICAR 120VAC LED DoB 4 IC/AIR-TIGHT Recessed Down Light for Remodeling 4 LED 12 (305mm) 5-5/8 (142.3mm) DESCRIPTION The LEDH-RT4ICAR housing is designed for use with a separate LED Trim Module that is integrated with heat sink and is available with three trim styles. This Remodeling fixture offer easy and fast installation using a disconnect device and is held securely in the housing with two friction blade brackets. The LED DoB 120VAC Direct module is available in a 11W engine with integral triac dimming and can be controlled with most of leading and trailing edge dimmer switches. This luminaire is listed as IC and is suitable for direct contact with insulation. Suitable for Damp Locations. Housing Single wall aluminum housing gasketed for IC/Air-Tight ratings in insulated ceilings. 5-1/2 height allows use in 2 x 6 joist construction. LED Module & Trim Two-piece interchangeable trim for reflectors or baffles. Module construction includes LED, Heat Sink, Lens, Trims. White paint finish standard. Junction Box Listed for through branch circuit wiring (Max.8, 12 AWG, 90 C wire). (5) 1/2" knockouts with pry-out slots and (4) knockouts with Romex cable clamps. Ground wire provided on J-box. Provided with listed quick connectors for easy wiring. Remodel Clips 3 remodel clips secure housing and accommodates 1/2 and 5/8 thick ceiling materials. Lens High Impact Thermal plastic. Translucent, high lumen transmission and diffusing for even illumination. LED Engine Aluminum Heat Sink computer designed in conjunction with an aluminum clad PC board for superior thermal management. Lumen Maintenance: L70, 70% lumens of initial 50,000 hours. Electrical Connection; Provided with quick connector between LED module and housing for easy plug and play installation. 120VAC Direct DoB Driver on Board with customized IC chip % triac dimmable with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for a maximum 45 fixtures per run on a 600W max load per dimmer switch and a max. 23 fixtures per a dimmer switch for a 300W load. Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing ENERGY STAR California Title /8 (105mm) 4-1/8 (105mm) Height : 5-5/8 Ceiling Cut-out : 4-3/8 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 11W Lumen (+/-5%) 750 lm Efficacy (LPW) 68 lm/w Beam Angle 27.8 CRI (Typical) 80 CCT (Color +/-5%) 2700K, 3000K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Damp Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers 07/19/18

24 LEDT-C44 Reflector -HC = Haze Clear -PR = Pewter -CP = Champagne -WH = White Painted O.D : 4-7/8" 4 LED LEDT-C44-WH-WH LEDT-C42 Baffle -WH = White -BK = Black O.D : 4-7/8" LEDT-C42-WH-WH LEDQT-42 Square Diecast Baffle -WH = White Frame : 4-3/4" x 4-3/4" LEDQT-42-WH LEDT-C411 Gimbal Adjustable -WH = White -BK = Black O.D : 4-7/8 LEDT-C411 PHOTOMETRIC REPORT * Contact Factory for IES File Polar Candela Distribution ,800 1,500 1, CD: ,200 1,500 1,800 VA: ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width fc 1.0 ft fc 2.0 ft 47.1 fc 3.0 ft 26.5 fc 4.0 ft 17.0 fc 5.0 ft 11.8 fc 5.9 ft Beam Spread: 27.8 [LEDH-RT4ICA(R) DOB+LEDT-C44-HC] Ordering Information Housing Trim / Module -Watts -CRI / Color Temp.* -Reflector Finish* -Baffle Finish* -Trim Ring Finish* -Driver LEDH-RT4ICA = 4 IC, New Construction LEDT-C44 = Reflector LEDT-C42 = Baffle LEDQT-42 = Square Diecast Baffle -11 = 11W -827 = 80 CRI / 2700K -830 = 80 CRI / 3000K -840 = 80 CRI / 4000K -HC = Haze Clear -PR = Pewter -CP = Champane -WH = White Painted -WH = White -BK = Black -WH = White -BK = Black -DOB = 120V Direct Driver on Board (dimmable with most Line or Low Voltage Dimmers) LEDT-C411 = Gimbal Adjustable Example : LEDH-RT4ICA LEDT-C HC-DOB * Consult factory for other Color Temperatures and Finishes

25 LED-AFR4 120VAC LED DoB 4 Recessed Diecast Retrokit with E26 or Optional GU24 base Adapter 4 LED 2-1/8 (54.5mm) DESCRIPTION 4-15/16 (126mm) 4-15/16 (126mm) The 4 LED DoB Retrokit Module & Trim kit with E26 medium base Adapter is designed for 6 IC/Airtight and Non-IC incandescent recessed downlights and has an optional GU24 adapter for CFL housings. It is designed for use with Lum-tech models IIH-410, IH-410ICA and most compatible 4 housings certified under UL1598 standard. High efficacy 120VAC DoB (Driver on Board) LED Module with integral triac dimmer capability. The optical diffusing lens produces high lumen transmission and even illumination. Suitable for Wet Locations. LED Module & Trim Efficient one-piece diecast aluminum heat sink, baffle and trim with integrated LED DoB module. High reflectance White Baffle style Reflector improves beam distribution and uniformity. Lens High impact translucent plastic lens. High lumen transmission and diffusing for even illumination. Compatible Housings See Housing Compatibility section. Electrical Connection; E26 medium Edison connector provides easy retrofit of screw based incandescent housings. Optional GU24 base Adapter available for CFL housings. 120VAC LED Power Supply on-board with stated-of-the-art customized IC chip (DoB) % triac dimmable with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for use max. 45 fixtures per run of a dimmer switch 600W loaded and max. 23 fixtures per a dimmer switch 300W loaded. Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Wet Location ENERGY STAR California Title 24 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 10 W Lumen (+/-5%) 625 lm Efficacy (LPW) 62.5 lm/w Beam Angle 90.5 CRI (Typical) 80, 90 CCT (Color +/-5%) 2700K, 3000K, 3500K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers

26 HOUSING COMPATIBILITY 4 LED LED-AFR4 ETL Listed for installation in the following Lum-Tech E26 screw based 4 standard and shallow recessed housings; 4 : IH-410, IH-410R, IH-410ICA, FEH-V4ICA-GU24, FEH-V4ICAR-GU24 (GU24 base adapter only) LED-AFR4 ETL Listed for retrokit in the following 4 recessed housing; Halo : H99T, H99RT, H99ICT All-Pro : ET400, ET400R, ET400AT Juno : TC1, TC1R, IC1P Capri : R4, RR4, R4ASIC Lithonia : L3, L3R Thomas : PS4, PS4RM, PS4ASIC PHOTOMETRIC REPORT * Contact Factory for IES File Polar Candela Distribution CD: VA: [LED-AFR4-830DOB] ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width 80.8 fc 4.0 ft 20.2 fc 8.1 ft 9.0 fc 12.1 ft 5.1 fc 16.1 ft 3.2 fc 20.2 ft 2.2 fc 24.2 ft Beam Spread: 90.5 Ordering Information Model -CRI Color Temp.* Finish* Driver -Options LED-AFR4 = 4, 10W Recessed Diecast Retrokit -8 = 80 CRI -9 = 90 CRI 27 = 2700K 30 = 3000K 40 = 4000K blank = White (Standard) DOB = 120V Direct Driver on Board (dimmable with most Line or Low Voltage Dimmers) -GU24A = GU24 Adapter -ZE = Genderless Quick Connector (Select when ordering with LEDH Housings) Example : LED-AFR4-830DOB-GU24A * Consult factory for other Color Temperatures and Finishes

27 LED-LFR4 120VAC LED DoB 4" Recessed Retrokit with E26 or Optional GU24 base Adapter 4 LED 1-3/4 (45mm) DESCRIPTION 4-15/16 (126mm) 4-15/16 (126mm) The 4 LED DoB Retrokit with E26 medium base Adapter ideal for 4 IC/Airtight and Non-IC incandescent recessed downlights and has an optional GU24 adapter for CFL housings. It is designed for use with Lum-Tech models IH-410, IH-410ICA and most 4 housings certified under UL1598 standard. High efficacy 120VAC LED DoB (Driver on Board) Module (Campcell ) with integral triac dimmer capability. The optical diffusing lens produces high lumen transmission and even illumination. Suitable for Wet Location. LED Module Efficient one piece aluminum heat sink, reflector or baffle and integrated LED DoB module. High reflectance White Reflector or Baffle improves beam distribution and uniformity. Lens High impact translucent plastic lens. High lumen transmission and diffusing for even illumination. Compatible Housings All 4 recessed housings from Halo, Juno, Capri, Lithonia, Thomas and Prescolite. Electrical Connection; E26 medium Edison connector provides easy retrokit of screw based incandescent housings. Optional GU24 base Adapter available for CFL housings. 120VAC LED Power Supply on-board with stated-of-the-art customized IC chip (DoB) % triac dimming with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for use max. 45 fixtures per run on a 600W max load dimmer switch. 23 fixtures per run on a 300W max load dimmer switch. Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Wet Location ENERGY STAR California Title 24 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 10 W Lumen (+/-5%) 625 lm Efficacy (LPW) 62.5 lm/w Beam Angle 90.5 CRI (Typical) 80, 90 CCT (Color +/-5%) 2700K, 3000K, 3500K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers

28 HOUSING COMPATIBILITY LED-LFR4 ETL Listed for installation in the following Lum-Tech E26 screw based 4 standard recessed housings; 4 : IH-410, IH-410R, IH-410ICA, FEH-V4ICA-GU24, FEH-V4ICAR-GU24 (GU24 base adapter only) 4 LED LED-LFR4 ETL Listed for retrokit in the following 4 recessed housing; Halo : H99T, H99RT, H99ICT All-Pro : ET400, ET400R, ET400AT Juno : TC1, TC1R, IC1P Capri : R4, RR4, R4ASIC Lithonia : L3, L3R Thomas : PS4, PS4RM, PS4ASIC PHOTOMETRIC REPORT * Contact Factory for IES File Polar Candela Distribution CD: VA: [LED-LFR4-830RWH-DOB] 2.0ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width 80.8 fc 4.0 ft 20.2 fc 8.1 ft 9.0 fc 12.1 ft 5.1 fc 16.1 ft 3.2 fc 20.2 ft 2.2 fc 24.2 ft Beam Spread: 90.5 Ordering Information Model -CRI Color Temp.* Finishes (Reflectors & Baffles)* -Driver -Options LED-LFR4 = 4, 120VAC, 10W Recessed Retrokit -8 = 80 CRI -9 = 90 CRI 27 = 2700K 30 = 3000K 35 = 3500K 40 = 4000K RWH = White Reflector RBK = Black Reflector BWH = White Baffle BBK = Black Baffle -DOB = 120V Direct Driver on Board (dimmable with most Line or Low Voltage Dimmers) -GU24A = GU24 Adapter -ZE = Genderless Quick Connector (Select when ordering with LEDH Housings) Example : LED-LFR4-830RWH-DOB-GU24A * Consult factory for other Color Temperatures and Finishes

29 LEDH-NCR5ICA 120VAC LED DoB 5 Recessed Housing Down Light with Baffle Trim for IC type New Construction Applications 5 LED 7-3/8 (187mm) 3-7/8 (98mm) DESCRIPTION 7-1/8 (181mm) 7-1/4 (184mm) Ceiling Cut-out : 5-1/2 The LEDH-NCR5ICA down light is a 5, IC rated luminaire. The LED DoB 120VAC Direct engine has a 12.5W LED Module with integral triac dimming and can be controlled with most of leading and trailing edge dimmer switches. This easy to install fixture is designed for New Construction applications with insulated ceilings. Thermally protected, Suitable for Wet Locations. LED Module & Trim Durable, one-piece die cast aluminum heat sink with integrated trim. Module construction includes LED, heat sink, lens and baffle trim. White painted finish standard. Lens High Impact Thermal plastic. Translucent, high lumen transmission and diffusing for even illumination. Sealed for Wet Locations and is ideal for shower rooms. Mounting Provided with a plaster frame (7-1/8 x 7-1/8 ) for new construction. HB-24 bar hangers are available as an accessory for new construction. Electrical Connection; J-box: - Installed on the top of fixture with (5)1/2 knockout. - Listed for through branch circuit wiring (max. 4, 12 AWG, 90 C rated wire). - Ground wire provided. 120VAC Direct DoB Driver on Board with customized IC chip % triac dimmable with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for a maximum 45 fixtures per run on a 600W max load per dimmer switch and a max. 23 fixtures per a dimmer switch for a 300W load. Accessories HB-24 hanger bars for use with housing plate for new construction applications Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Wet Location ENERGY STAR California Title 24 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 12.5 W Lumen (+/-5%) 895 lm Efficacy (LPW) 71.6 lm/w Beam Angle 96.3 CRI (Typical) 80, 90 CCT (Color +/-5%) 2700K, 3000K, 3500K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers

30 LEDH-NCR5ICAR 120VAC LED DoB 5 Recessed Housing Down Light with Baffle Trim for IC type Remodeling Applications 5 LED 7-1/4 (184mm) 3-7/8 (98mm) DESCRIPTION 7-1/4 (184mm) 7-1/4 (184mm) Ceiling Cut-out : 5-1/2 The LEDH-NCR5ICAR down light is a 5, IC rated luminaire. The LED DoB 120VAC Direct engine has a 12.5W LED Module with integral triac dimming and can be controlled with most of leading and trailing edge dimmer switches. This easy to install fixture is designed for Remodeling applications with insulated ceilings. Thermally protected, Suitable for Wet Locations. LED Module & Trim Durable, one-piece diecast aluminum heat sink with integrated trim. Module construction includes LED, heat sink, lens and baffle trim. (2) mounting clips on trim module for remodeling jobs. White painted finish standard. Lens High Impact Thermal plastic. Translucent, high lumen transmission and diffusing for even illumination. Sealed for Wet Locations and is ideal for shower rooms. Electrical Connection; J-box: - Installed on the top of fixture with (5)3/4 knockout. - Listed for through branch circuit wiring (max. 8, 12 AWG, 90 C wire). - Ground wire provided. 120VAC Direct DoB Driver on Board with customized IC chip % triac dimmable with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for a maximum 45 fixtures per run on a 600W max load per dimmer switch and a max. 23 fixtures per a dimmer switch for a 300W load. Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Wet Location ENERGY STAR California Title 24 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 12.5 W Lumen (+/-5%) 895 lm Efficacy (LPW) 71.6 lm/w Beam Angle 96.3 CRI (Typical) 80, 90 CCT (Color +/-5%) 2700K, 3000K, 3500K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers

31 5 LED PHOTOMETRIC REPORT * Contact Factory for IES File Polar Candela Distribution CD: VA: ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width fc 4.5 ft 26.5 fc 8.9 ft 11.8 fc 13.4 ft 6.6 fc 17.9 ft 4.2 fc 22.3 ft 2.9 fc 26.8 ft Beam Spread: 96.3 [LEDH-NCR5ICA(R)-830DOB] Ordering Information Model -CRI Color Temp.* Finish* Driver Accessories LEDH-NCR5ICA= 5, 12.5W Recessed IC, New Construction LEDH-NCR5ICAR = 5, 12.5W Recessed IC, Remodeling -8 = 80 CRI -9 = 90 CRI 27 = 2700K 30 = 3000K 40 = 4000K blank = White (Standard) DOB = 120V Direct Driver on Board (dimmable with most Line or Low Voltage Dimmers) HB-24 = 24 adjustable Hanger Bars (2) LEDH-NCR5ICA only Example : LEDH-NCR5ICA-830DOB * Consult factory for other Color Temperatures and Finishes

32 LEDH-RT56ICA 6 IC/AIR-TIGHT Recessed Down Light Housing for New Construction with Lum-Tech 120VAC LED DoB 56 and 6" Retrokits 7-1/2" (190mm) 10-3/8" (263.5mm) 6-1/8" (157mm) 7-5/8" (193.6mm) 2-11/16" (68mm) DESCRIPTION [Shown with LED-AFR56 Retrokit ] 7-1/4" (184mm) Height : 7-1/2 Housing Aperture : 6-1/8 Ceiling Cut-out : 6-1/2 The LEDH-RT56ICA is a 6, IC/AIR TIGHT rated down light housing. This easy to install housing is designed for use in New Construction applications with insulated ceilings. The housing is designed to be used with Lum-Tech s 56 and 6 Retrokits and gives you a choice of seven versatile DOB kits for your projects. Housing Single wall aluminum housing gasketed for IC/Air-Tight ratings in insulated ceilings. Housing can be adjusted for ceiling thicknesses up to 1-1/4 Junction Box Listed for through branch circuit wiring (Max.8, 12 AWG, 90 C wire). (5) 1/2" knockouts with pry-out slots and (4) knockouts with Romex cable clamps. Ground wire provided on J-box. Provided with listed ZE genderless quick connectors for easy wiring to Lum-Tech retrokits. Compatible Lum-Tech LED DoB Retrokits LED-AFR56: 120VAC LED DoB 5 and 6 Recessed Diecast Retrokit LED-LFR56: 120VAC LED DoB 5 and 6 Recessed Retrokit LED-AFC6: 120VAC LED DoB 6 Recessed Retrokit with Interchangeable Trims LED-AF6E : 120VAC LED DoB 6 Recessed Eyeball Retrokit LED-LF6AD : 120VAC LED DoB 6 Recessed Gimbal Retrokit 11/15/17

33 LEDH-RT56ICAR 6 IC/AIR-TIGHT Recessed Down Light Housing for Remodeling with Lum-Tech 120VAC LED DoB 56 and 6" Retrokits 12-3/4 (324mm) 7-1/2 (191mm) 6-1/8 (157mm) 2-11/16" (68mm) DESCRIPTION [Shown with LED-AFR56 Retrokit ] 7-1/4" (184mm) Height : 7-1/2 Ceiling Cut-out : 6-1/2 The LEDH-RT56ICAR is a 6, IC/AIR TIGHT rated down light housing. This easy to install housing is designed for use in Remodeling applications with insulated ceilings. The housing is designed to be used with Lum-Tech s 56 and 6 Retrokits and gives you a choice of seven versatile DOB kits for your projects. This luminaire is listed as IC and is suitable for direct contact with insulation. Housing Single wall aluminum housing gasketed for IC/Air-Tight ratings in insulated ceilings. 7-1/2 height allows use in 2 x 8 joist construction. Junction Box Listed for through branch circuit wiring (Max.8, 12 AWG, 90 C wire). (5) 1/2" knockouts with pry-out slots and (4) knockouts with Romex cable clamps. Ground wire provided on J-box. Provided with listed ZE quick connectors for easy wiring to Lum-Tech retrokits. Compatible Lum-Tech LED DoB Retrokits LED-AFR56 : 120VAC LED DoB 5 and 6 Recessed Diecast Retrokit LED-LFR56 : 120VAC LED DoB 5 and 6 Recessed Retrokit LED-AFC6 : 120VAC LED DoB 6 Recessed Retrokit with Interchangeable Trims LED-AF6E : 120VAC LED DoB 6 Recessed Eyeball Retrokit LED-LF6AD : 120VAC LED DoB 6 Recessed Gimbal Retrokit 11/15/17

34 LED-AFR56 120VAC LED DoB 5" & 6 Diecast recessed Retrokit with E26 or Optional GU24 base Adapter 5 & 6 LED 2-11/16 (68mm) DESCRIPTION 7-1/4 (184mm) 7-1/4 (184mm) The 6 Diecast Retrokit LED module & trim kit with E26 medium screw base is designed for the 5 and 6 IC/Airtight and Non-IC incandescent recessed downlight and has an optional GU24 adapter for CFL housings. It is designed for use with Lum-Tech models IH-520ICA, IH-620ICA, IH-520, IH-620, shallow IH-640ICA, IH-640 and most 5 and 6 housings certified under UL1598 standard. High efficacy 120V DOB LED (Driver on Board) Module (Campcell ) with integral triac dimming capability. The optical diffusing lens produces high lumen transmission and even illumination. Suitable for Wet Location. LED Module & Trim Efficient diecast aluminum heat sink/baffle with integrated LED DoB module. High reflectance White Baffle style Reflector improves beam distribution and uniformity. Lens High impact translucent plastic lens. High lumen transmission and diffusing for even illumination. Mounting Dual torsion springs easily mount and adjust to compatible 5" & 6" recessed housings that have spring mounting tabs. Compatible Housings See Housing Compatibility section Electrical Connection; E26 medium Edison connector provides easy retrofit of screw based incandescent housings. Optional GU24 base Adapter available for CFL housings. 120VAC LED Power Supply on-board with stated-of-the-art customized IC chip (DoB) % triac dimming with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for use max. 45 fixtures per run on a 600W max load dimmer switch. 23 fixtures per run on a 300W max load dimmer switch. Warranty Lamp Life: 5 years/50k hours. Listing cetlus Wet Location ENERGY STAR California Title 24 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 12.5 W Lumen (+/-5%) 895 lm Efficacy (LPW) 71.6 lm/w Beam Angle 96.3 CRI (Typical) 85 CCT (Color +/-5%) 2700K, 3000K, 3500K, 4000K Dimming Triac Lamp Life 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers

35 5 & 6 LED HOUSING COMPATIBILITY LED-AFR56 ETL Listed for installation in the following Lum-Tech E26 screw based 5 and 6 standard and shallow recessed housings; 5 : IH-520ICA, IH-520ICAR, IH-520I, IH-520R 6 : IH-620ICA, IH-620ICAR, IH-610, IH-620R, Shallow: IH-640ICA, IH-640ICAR, IH-640, IH-640R LED-AFR56 ETL Classifed for retrokit in the following 5 and 6 recessed housing; Halo : H7ICAT, H7RICAT, H7ICT, H7RICT, H7ICATNB, H7ICTNB, H7T, H7RT, H7TNB, H7TCP, H7UICT, H7UICAT, H27ICAT, H27RICAT, H27ICT, H27RICT, H27T, H27RT, H5ICAT, H5RICAT, H5T, H5RT, H25ICAT All-Pro : 500AT, EI500RAT, ET500, ET500R, EI700AT, EI700RAT, E700ATNB, EI700, EI700R, EI700ATNB, EI700NB, ET700, ET700R, EI700U, EI700UAT, E2700AT, EI2700, EI2700R, ET2700, ET2700R Juno : IC22, IC22R, IC22W,IC22S,IC23, IC23W, IC21, IC21R, TC2, TC2R, IC20, IC20R, IC25, IC25R, IC25W, IC25S, TC20, TC20R Capri : CR1, PR1, QL1. R9ASIC Lithonia : L7X, L7XP Thomas : PS1, R9ASIC/PS9RM Prescolite : IBXS PHOTOMETRIC REPORT * Contact Factory for IES File Polar Candela Distribution CD: VA: [LED-AFR56-830DOB] ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width fc 4.5 ft 26.5 fc 8.9 ft 11.8 fc 13.4 ft 6.6 fc 17.9 ft 4.2 fc 22.3 ft 2.9 fc 26.8 ft Beam Spread: 96.3 Ordering Information Model Color Temp.* Finish* Driver -Options LED-AFR56 = 5 /6, 12.5W Recessed Diecast Retrokit 27 = 2700K 30 = 3000K 35 = 3500K 40 = 4000K blank = White (Standard) DOB = 120V Direct Driver on Board (dimmable with most Line or Low Voltage Dimmers) -GU24A = GU24 Adapter -ZE = Genderless Quick Connector (Select when ordering with LEDH Housings) Example : LED-AFR56-830DOB-GU24A * Consult factory for other Color Temperatures and Finishes 02/07/17

36 LED-LFR56 120VAC LED DoB 5 and 6 Recessed Retrokit with E26 or Optional GU24 base Adapter 5 & 6 LED 2-1/2 (63mm) DESCRIPTION 7-1/4 (184mm) The 5 & 6 LED DoB Retrokit Module & Trim kit with E26 medium base Adapter is designed for 5 & 6 IC/Airtight and Non-IC incandescent recessed downlights and has an optional GU24 adapter for CFL housings. Selection of interchangeable trim styles and finishes complement any design. It is designed for use with Lum-Tech models IH-520ICA, IH-620ICA, IH-520, IH-620, shallow IH-640ICA, IH-640 and most 5 & 6 housings certified under UL1598 standard. High efficacy 120VAC LED DoB (Driver on Board) Module (Campcell ) with integral triac dimmer capability. The optical diffusing lens produces high lumen transmission and even illumination. Suitable for Wet Location. LED Module Efficient aluminum heat sink with integrated DOB LED module. High reflectance White Reflectors and Baffles improve beam distribution and uniformity. Trim Available with Reflector or Baffle styles in standard and custom colors. Lens High impact translucent plastic lens. High lumen transmission and diffusing for even illumination. Mounting Precision formed steel torsion springs. Dual torsion springs easily mount and adjust to compatible 5" & 6" recessed housings that have spring mounting tabs. Easy trim installation with snap-on clips. Compatible Housings All 5" & 6 recessed housings from Halo, Juno, Capri, Lithonia, Thomas and Prescolite. Electrical Connection; E26 medium Edison connector provides easy retrokit of screw based incandescent housings. Optional GU24 base Adapter available for CFL housings. 120VAC LED Power Supply on-board with stated-of-the-art customized IC chip (DoB) % triac dimming with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for use max. 45 fixtures per run of a dimmer switch 600W loaded and max. 23 fixtures per a dimmer switch 300W loaded. Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Wet Location ENERGY STAR California Title 24 ID 7-1/4 (184mm) [ ID ] LED-LFR56 : 4-7/8 SPECIFICATION Item No. LED-LFR56 Input Voltage 120VAC Wattage (+/-5%) 12.5 W Lumen (+/-5%) 810 lm Efficacy (LPW) 64.8 lm/w Beam Angle 92.7 CRI (Typical) 80, 90 CCT (Color +/-5%) 2700K, 3000K, 3500K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers 10/26/17

37 HOUSING COMPATIBILITY 5 & 6 LED LED-LFR56 ETL Listed for installation in the following Lum-Tech E26 screw based 5 and 6 standard and shallow recessed housings; 5 : IH-520ICA, IH-520ICAR, IH-520I, IH-520R 6 : IH-620ICA, IH-620ICAR, IH-610, IH-620R, Shallow: IH-640ICA, IH-640ICAR, IH-640, IH-640R LED-LFR56 ETL Listed for retrokit in the following 5 and 6 recessed housing; Halo : H7ICAT, H7RICAT, H7ICT, H7RICT, H7ICATNB, H7ICTNB, H7T, H7RT, H7TNB, H7TCP, H7UICT, H7UICAT, H27ICAT, H27RICAT, H27ICT, H27RICT, H27T, H27RT, H5ICAT, H5RICAT, H5T, H5RT, H25ICAT All-Pro : 500AT, EI500RAT, ET500, ET500R, EI700AT, EI700RAT, E700ATNB, EI700, EI700R, EI700ATNB, EI700NB, ET700, ET700R, EI700U, EI700UAT, E2700AT, EI2700, EI2700R, ET2700, ET2700R Juno : IC22, IC22R, IC22W,IC22S,IC23, IC23W, IC21, IC21R, TC2, TC2R, IC20, IC20R, IC25, IC25R, IC25W, IC25S, TC20, TC20R Capri : CR1, PR1, QL1. R9ASIC Lithonia : L7X, L7XP Thomas : PS1, R9ASIC/PS9RM Prescolite : IBXS LED-LFR56 Retrokit Reflectors and Baffles Reflector White or Clear Reflector O.D : 7-1/4" (184mm) for 5/6 housing Baffle White or Black Baffle O.D : 7-1/4" (184mm) for 5/6 housing RWH BWH PHOTOMETRIC REPORT * Contact Factory for IES File Polar Candela Distribution CD: VA: [LED-LFR56-830DOB] ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width fc 4.2 ft 25.9 fc 8.4 ft 11.5 fc 12.6 ft 6.5 fc 16.8 ft 4.1 fc 21.0 ft 2.9 fc 25.2 ft Beam Spread: 92.7 Ordering Information Model -CRI Color Temp.* Finishes (Reflectors & Baffles)* -Driver -Options LED-LFR56 = 5 / 6, 120VAC, 12.5W Recessed Retrokit -8 = 80 CRI -9 = 90 CRI 27 = 2700K 30 = 3000K 35 = 3500K 40 = 4000K RWH = White Reflector RBK = Black Reflector BWH = White Baffle BBK = Black Baffle -DOB = 120V Direct Driver on Board (dimmable with most Line or Low Voltage Dimmers) -GU24A = GU24 Adapter -ZE = Genderless Quick Connector (Select when ordering with LEDH Housings) Example : LED-LFR56-830RWH-DOB-GU24A * Consult factory for other Color Temperatures and Finishes

38 LED-AFC6 120VAC LED DoB 6 Recessed Retrokit with Interchangeable Trims and E26 or Optional GU24 base Adapters 6 LED 4-5/16 (110.2mm) DESCRIPTION 7-9/16 (192mm) 5-11/16 (144mm) The 6 LED DoB Retrokit Module & Trim kit with E26 medium base Adapter is designed for 6 IC/Airtight and Non-IC incandescent recessed downlights and has an optional GU24 adapter for CFL housings. It is designed for use with Lum-tech models IH-620ICA, IH-620, shallow IH-640ICA, IH-640 and most 6 housings certified under UL1598 standard. High efficacy 120VAC DoB (Driver on Board) LED Module (Campcell ) with integral triac dimmer capability. The optical diffusing lens produces high lumen transmission and even illumination. Suitable for Wet Location. LED Module Efficient aluminum extrusion heat sink with integrated LED DoB module High reflectance White Reflectors and Baffles improves beam distribution and uniformity. Trims Available with Reflectors in White or anodized Clear Haze and Baffle trims in White or Black. Lens High impact translucent plastic lens. High lumen transmission and diffusing for even illumination. Mounting Precision formed steel torsion springs easily adjust to 6" housings. Dual torsion springs easily mount into compatible 6" recessed housings that have spring mounting tabs. Easy trim installation with snap-on clips. Compatible Housings See Housing Compatibility section Electrical Connection; E26 medium Edison connector provides easy retrokit of screw based incandescent housings. Optional GU24 base Adapter available for CFL housings. 120VAC LED Power Supply on-board with stated-of-the-art customized IC chip (DoB) % triac dimming with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for use max. 45 fixtures per run of a dimmer switch 600W loaded and max. 23 fixtures per a dimmer switch 300W loaded. Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Wet Location ENERGY STAR California Title 24 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 12.5 W Lumen (+/-5%) 885 lm Efficacy (LPW) 70.8 lm/w Beam Angle 54.3 CRI (Typical) 80, 90 CCT (Color +/-5%) 2700K, 3000K, 3500K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers

39 6 LED HOUSING COMPATIBILITY LED-AFC6 ETL Listed for installation in the following Lum-Tech E26 screw based 6 standard and shallow recessed housings; 6 : IH-620ICA, IH-620ICAR, IH-610, IH-620R, Shallow: IH-640ICA, IH-640ICAR, IH-640, IH-640R LED-AFC6 ETL Listed for retrokit in the following 6 recessed housing; Halo : H7ICAT, H7RICAT, H7ICT, H7RICT, H7ICATNB, H7ICTNB, H7T, H7RT, H7TNB, H7TCP, H7UICT, H7UICAT, H27ICAT, H27RICAT, H27ICT, H27RICT, H27T, H27RT, H5ICAT, H5RICAT, H5T, H5RT, H25ICAT All-Pro : EI700AT, EI700RAT, E700ATNB, EI700, EI700R, EI700ATNB, EI700NB, ET700, ET700R, EI700U, EI700UAT, E2700AT, EI2700, EI2700R, ET2700, ET2700R Juno : IC22, IC22R, IC22W,IC22S,IC23, IC23W, IC21, IC21R, TC2, TC2R, IC20, IC20R, IC25, IC25R, IC25W, IC25S, TC20, TC20R Capri : CR1, PR1, QL1. R9ASIC Lithonia : L7X, L7XP Thomas : PS1, R9ASIC/PS9RM Prescolite : IBXS LED-AFC6 Retrokit Reflectors and Baffles Reflector White or Clear Reflector O.D : 7-9/16" (192mm) for 5/6 housing Baffle White or Black Baffle O.D : 7-9/16" (192mm) for 5/6 housing RHC RWH BWH PHOTOMETRIC REPORT * Contact Factory for IES File Polar Candela Distribution CD: VA: [LED-AFC6-827RHC-DOB] 2.0ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width fc 2.0 ft 56.9 fc 4.1 ft 25.3 fc 6.1 ft 14.2 fc 8.2 ft 9.1 fc 10.2 ft 6.3 fc 12.3 ft Beam Spread: 54.3 Ordering Information Model -CRI Color Temp.* Finishes (Reflectors & Baffles)* -Driver -Options LED-AFC6 = 6", 120VAC, 12.5W Recessed Retrokit with Interchangeable Trims -8 = 80 CRI -9 = 90 CRI 27 = 2700K 30 = 3000K 35 = 3500K 40 = 4000K RWH = White Reflector RHC = Haze Clear Reflector BWH = White Baffle BBK = Black Baffle -DOB = 120V Direct Driver on Board (dimmable with most Line or Low Voltage Dimmers) -GU24A = GU24 Adapter -ZE = Genderless Quick Connector (Select when ordering with LEDH Housings) Example : LED-AFC6-830RWH-DOB-GU24A * Consult factory for other Color Temperatures and Finishes

40 LED-AF6E 120VAC LED DoB 6" Recessed Eyeball Retrokit with E26 or Optional GU24 base Adapter 6 LED 3-3/16 (80.6mm) DESCRIPTION 7-3/4 (196.5mm) 4-1/2 (114.9mm) The 6 eyeball LED Retrokit Module & Trim kit with E26 medium base Adapter is designed for 6 IC/Airtight and Non-IC incandescent recessed downlights and has an optional GU24 adapter for CFL housings. It is designed for use with Lum-Tech models IH-620ICA, IH-620, shallow IH-640ICA, IH-640 and most 6 housings certified under UL1598. High efficacy 120VAC DoB (Driver on Board) LED Module (Campcell ) with integral triac dimmer capability. The optical diffusing lens produces high lumen transmission and even illumination. Suitable for Wet Location. LED Module Efficient aluminum extrusion heat sink with integrated LED DoB module. Eyeball head rotates 358 degrees and can tilt 0-30 degrees. Lens High impact translucent plastic lens. High lumen transmission and diffusing for even illumination. Mounting Precision formed steel torsion springs easily adjust to 6" housings. Dual torsion springs easily mount into compatible 6" recessed housings that have spring mounting tabs. Compatible Housings See Housing Compatibility section Electrical Connection; E26 medium Edison connector provides easy retrokit of screw based incandescent housings. Optional GU24 base Adapter available for CFL housings. 120VAC LED Power Supply on-board with stated-of-the-art customized IC chip (DoB) % triac dimming with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for use max. 45 fixtures per run on a 600W max load dimmer switch. 23 fixtures per run on a 300W max load dimmer switch. Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Wet Location ENERGY STAR California Title 24 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 12.5 W Lumen (+/-5%) 820 lm Efficacy (LPW) 65.6 lm/w Beam Angle 78.9 CRI (Typical) 80, 90 CCT (Color +/-5%) 2700K, 3000K, 3500K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers

41 6 LED HOUSING COMPATIBILITY LED-AF6E ETL Listed for installation in the following Lum-Tech E26 screw based 6 standard and shallow recessed housings; 6 : IH-620ICA, IH-620ICAR, IH-610, IH-620R, Shallow: IH-640ICA, IH-640ICAR, IH-640, IH-640R LED-AF6E ETL Listed for retrokit in the following 6 recessed housing; Halo : H7ICAT, H7RICAT, H7ICT, H7RICT, H7ICATNB, H7ICTNB, H7T, H7RT, H7TNB, H7TCP, H7UICT, H7UICAT, H27ICAT, H27RICAT, H27ICT, H27RICT, H27T, H27RT, H5ICAT, H5RICAT, H5T, H5RT, H25ICAT All-Pro : EI700AT, EI700RAT, E700ATNB, EI700, EI700R, EI700ATNB, EI700NB, ET700, ET700R, EI700U, EI700UAT, E2700AT, EI2700, EI2700R, ET2700, ET2700R Juno : IC22, IC22R, IC22W,IC22S,IC23, IC23W, IC21, IC21R, TC2, TC2R, IC20, IC20R, IC25, IC25R, IC25W, IC25S, TC20, TC20R Capri : CR1, PR1, QL1. R9ASIC Lithonia : L7X, L7XP Thomas : PS1, R9ASIC/PS9RM Prescolite : IBXS PHOTOMETRIC REPORT * Contact Factory for IES File Polar Candela Distribution CD: VA: [LED-AF6E-830DOB] ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width fc 3.3 ft 29.6 fc 6.6 ft 13.2 fc 9.9 ft 7.4 fc 13.2 ft 4.7 fc 16.5 ft 3.3 fc 19.8 ft Beam Spread: 78.9 Ordering Information Model -CRI Color Temp.* Finish* Driver -Options LED-AF6E = 6", 120VAC, 12.5W Recessed Eyeball Retrokit -8 = 80 CRI -9 = 90 CRI 27 = 2700K 30 = 3000K 35 = 3500K 40 = 4000K blank = White (Standard) DOB = 120V Direct Driver on Board (dimmable with most Line or Low Voltage Dimmers) -GU24A = GU24 Adapter -ZE = Genderless Quick Connector (Select when ordering with LEDH Housings) Example : LED-AF6E-830DOB-GU24A * Consult factory for other Color Temperatures and Finishes

42 LED-AF6AD 120VAC LED DoB 6 Recessed Gimbal Retrokit with E26 or Optional GU24 base Adapter 6 LED 3-3/16 (80.6mm) DESCRIPTION 7-3/4 (196.5mm) 4-15/16 (125mm) The 6 LED DoB Gimbal Retrokit with E26 medium base Adapter ideal for 6 IC/Airtight and Non-IC incandescent recessed downlights and has an optional GU24 adapter for CFL housings. It is designed for use with Lum-Tech models IH-620ICA, IH-620, shallow IH-640ICA, IH-640 and most 6 housings certified under UL1598 standard. High efficacy 120VAC LED DoB (Driver on Board) Module (Campcell ) with integral triac dimmer capability. The optical diffusing lens produces high lumen transmission and even illumination. Suitable for Wet Locationn. LED Module Efficient aluminum extrusion heat sink with integrated LED DoB module. Gimbal head rotates 358 degrees and can tilt 0-30 degrees. High reflectance Reflector improves beam distribution and uniformity Lens High impact translucent plastic lens. High lumen transmission and diffusing for even illumination. Mounting Precision formed steel torsion springs easily adjust to 6" housings. Dual torsion springs easily mount into compatible 6" recessed housings that have spring mounting tabs. Compatible Housings See Housing Compatibility section Electrical Connection; E26 medium Edison connector provides easy retrokit of screw based incandescent housings. Optional GU24 base Adapter available for CFL housings. 120VAC LED Power Supply on-board with stated-of-the-art customized IC chip (DoB) % triac dimming with most of leading and trailing edge incandescent & low voltage dimmer switches. Advanced driver circuit design (Pat. Pending) prevents damage to the LED module and switch from common inrush currents. Recommended for use max. 45 fixtures per run on a 600W max load dimmer switch. 23 fixtures per run on a 300W max load dimmer switch. Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetlus Wet Location ENERGY STAR California Title 24 SPECIFICATION Input Voltage 120VAC Wattage (+/-5%) 12.5 W Lumen (+/-5%) 900 lm Efficacy (LPW) 72 lm/w Beam Angle 74 CRI (Typical) 80, 90 CCT (Color +/-5%) 2700K, 3000K, 3500K, 4000K Dimming Triac LED Module 5 yr/50k hr Environment Wet Location Trailing Edge Dimmer Diva DVCL Series Diva DVLV Series Nova T NT Series Glyder GLV Series Ariadni AYCL Series RadioRA 2 10ND Series Skylark SLV Series Skylark SLV Series Skylark Contour CTCL Series Maestro Wireless MRF2-6ND Series Lutron Homeworks RPM-4U Lutron Homeworks QS HQRD-6ND Series Lutron Homeworks QS HQRD-10ND Series - Leviton Model Numbers : SureSlide 6633 Leading Edge Dimmer Diva DVELV Series Skylark SELV Series Nova T NTELV Series RadioRA RRD-6NA Series Maestro MAELV Series Maestro MRF2-6ELV Series Lutron Grafik Eye PHPM-PA Series Lutron Homeworks QS HQRD-6NA Series Consult tech. service or factory for additional dimmers

43 6 LED HOUSING COMPATIBILITY LED-AF6AD ETL Listed for installation in the following Lum-Tech E26 screw based 6 standard and shallow recessed housings; 6 : IH-620ICA, IH-620ICAR, IH-610, IH-620R, Shallow: IH-640ICA, IH-640ICAR, IH-640, IH-640R LED-AF6AD ETL Listed for retrokit in the following 6 recessed housing; Halo : H7ICAT, H7RICAT, H7ICT, H7RICT, H7ICATNB, H7ICTNB, H7T, H7RT, H7TNB, H7TCP, H7UICT, H7UICAT, H27ICAT, H27RICAT, H27ICT, H27RICT, H27T, H27RT, H5ICAT, H5RICAT, H5T, H5RT, H25ICAT All-Pro : EI700AT, EI700RAT, E700ATNB, EI700, EI700R, EI700ATNB, EI700NB, ET700, ET700R, EI700U, EI700UAT, E2700AT, EI2700, EI2700R, ET2700, ET2700R Juno : IC22, IC22R, IC22W,IC22S,IC23, IC23W, IC21, IC21R, TC2, TC2R, IC20, IC20R, IC25, IC25R, IC25W, IC25S, TC20, TC20R Capri : CR1, PR1, QL1. R9ASIC Lithonia : L7X, L7XP Thomas : PS1, R9ASIC/PS9RM Prescolite : IBXS PHOTOMETRIC REPORT * Contact Factory for IES File Polar Candela Distribution CD: VA: [LED-AF6AD-830DOB] 2.0ft 4.0ft 6.0ft 8.0ft 10.0ft 12.0ft Illuminance at a Distance Center Beam FC Beam Width fc 3.0 ft 33.2 fc 6.0 ft 14.8 fc 9.0 ft 8.3 fc 12.0 ft 5.3 fc 15.0 ft 3.7 fc 18.0 ft Beam Spread: 74 Ordering Information Model -CRI Color Temp.* Finish* Driver -Options LED-AF6AD = 6", 120VAC, 12.5W Recessed Gimbal Retrokit -8 = 80 CRI -9 = 90 CRI 27 = 2700K 30 = 3000K 35 = 3500K 40 = 4000K blank = White (Standard) DOB = 120V Direct Driver on Board (dimmable with most Line or Low Voltage Dimmers) -GU24A = GU24 Adapter -ZE = Genderless Quick Connector (Select when ordering with LEDH Housings) Example : LED-AF6AD-830DOB-GU24A * Consult factory for other Color Temperatures and Finishes

44 TMS12 Series 4 and 6 Square, 120 or 277VAC LED DoB, Recessed Retrofit with E26 and Optional GU24 Base Adapters 4 & 6 LED [ TMS124 ] [ TMS126 ] LED Square Recessed Mount 5-1/8 (130mm) 1-9/16 (39mm) 7-7/16 (189.5mm) 1-15/16 (50mm) 5-1/8 (130mm) 5-1/8 (130mm) 7-7/16 (189.5mm) 7-7/16 (189.5mm) DESCRIPTION The 4 and 6 Square Retrofits are low profile recessed LED module & trim kits with an E26 medium screw base adaptor for 4 and 6 IC/Airtight and Non-IC incandescent recessed downlights. An Optional GU24 adapter for CFL housing is also available. They are designed for use with most 4 and 6 housings. FEATURES and FUNCTION Features One piece light engine integrated with durable diecast aluminum housing. Easy Installation into housing via spring clips that is compatible with most 4 cans (TMS124) and 6 cans (TMS126). Heat treated, frosted glass provides a soft, luminous glow. 120 or 277VAC LED DoB module with integrated IC chip imbedded on board. E26 adaptor is standard, optional GU24 adaptor for CFL sockets available. Triac dimming standard. Input Voltage Wattage (Typ) Lumen (Typ) Efficacy (LPW) Compatible Housing C R I (Typical) Color (+/-5% ) Dimming Limited Warranty LED Module: 5 years/50k hours Product: 3 years Listing cetl-us Damp Location ENERGY STAR California Title 24 SPECIFICATION 120VAC or 277VAC 10 W 15 W 700 (90CRI) 1,000 (90CRI) 70 lm/w 66.5 lm/w See Housing Compatibility section 80, K, 3000K, 3500K 4000K Triac Ordering Information * Consult with factory for approved dimmers Model -CRI Color Temp.* Housing Finish* -Voltage -Options TMS124 = 4 LED Square, 120 or 277VAC DoB, 10W Retrofit TMS126 = 6 LED Square, 120 or 277VAC DoB, 15W Retrofit -8 = 80 CRI -9 = 90 CRI 27 = 2700K 30 = 3000K 35 = 3500K 40 = 4000K -WH = White -DOB1 = 120VAC -DOB2 = 277VAC -GU24A = GU24 Adapter Example : TMS WH-DOB1 ** Consult factory for other Color Temperatures and Finishes 03/29/18