HYDRAULICALLY DRIVEN PUMPS SELECTION GUIDE VERSION

Transcription

1 HYDRAULICALLY DRIVEN PUMPS SELECTION GUIDE VERSION

2 TABLE OF CONTENTS PAGES HYDRAULIC PUMPS/MOTORS OVERVIEW 1-11 HYDRAULIC SUBASSEMBLY FEATURES FM5 & 8 Performance curves Dimensional Drawings 19 Exploded Parts/Drawings FM8 HY SPEED Performance curves Dimensional Drawings 27 Exploded Parts/Drawings FM10 & 15 Performance curves 30 Dimensional Drawings 31 Exploded Parts/Drawings HHLF & 2CT Performance curves Dimensional Drawings Exploded Parts/Drawings SERIES 30 & 80 Performance curves Dimensional Drawings Exploded Parts/Drawings SERIES 60, 80 & 120 HY SPEED Performance curves Dimensional Drawings Exploded Parts/Drawings SERIES 120 PEDESTAL Performance curves 79 Dimensional Drawings 80 Exploded Parts/Drawings SERIES 300 Performance curves Dimensional Drawings 85 Exploded Parts/Drawings CHEMFLO 1-4 HY SPEED Performance curves Dimensional Drawings Exploded Parts/Drawings i MP PUMPS, INC. PHONE: (800) FAX: (586)

3 CHEMFLO 5-8 Performance curves Dimensional Drawings Exploded Parts/Drawings HYDRASUB Performance curves Dimensional Drawings Exploded Parts/Drawings HYDRAULIC SUBASSEMBLIES Pedestal Dimensional Drawings. 138 Pedestal Exploded Parts/Drawings HY Speed Dimensional Drawings HY Speed Exploded Parts/Drawings Ultra Motor Pedestal Dimensional Drawings. 163 Ultra Motor Exploded Parts/Drawings. 164 ii MP PUMPS, INC. PHONE: (800) FAX: (586)

4 HYDRAULICALLY DRIVEN PUMPS MP Pumps has the most comprehensive hydraulically driven/ centrifugal pump product line to meet your application requirements. Typical applications are bulk transfer, application spraying, stripping, and sump/vault water removal. Every MP pump that is offered close coupled to an electric motor has one or more hydraulically driven bearing frames available with up to four different motor displacements to match the needs of most hydraulic systems. All of the pumps are close coupled to a hydraulic motor drive that uses oversized high quality ball bearings where some motors are integrally designed into the bearing frame to eliminate coupling two shafts. Pump materials available are cast iron, bronze, stainless steel, and aluminum. Pump flow rates up to 500 GPM and total developed head up to 400 feet. Hydraulically driven pump products are shown in three groups. Self priming FM5, 8, 10, 15, HHLF, 2CT End Suction S30, 60, 80, 120, 300, CF1, 2, 3, 4, 5, 6, 7, 8 Submersible HydraSub 20, 25, 30 MP Pumps offers high speed gerotor and gear type motors to drive the centrifugal pump with three different bearing frame arrangements sized to meet oil flow, pressure and load required. Pump and motor selection can be made by following the outline where the pump is selected first then motor options can be evaluated to choose the best motor selection. Performance data, outline drawings, and features can viewed for each selection. 1 MP PUMPS, INC. PHONE: (800) FAX: (586)

5 Determine Pump Selection Product line matrix Pump Model Max Flow Rate (GPM) Max Pump Press. (psi) Material of Const. Inlet (inches) Outlet (inches) Motor Displacement (cu-in/rev) Max Oil Flow (gpm) SELF PRIMING Flomax Al, Br, CI 1 1/2 1 1/2.22,.37, Flomax Al, Br, CI, SS ,.45, Flomax Br, CI, SS Flomax Br, CI, SS HHLF /2 1 1/ Br, CI HHLF CT CI END SUCTION Series Br, CI 1 3/4.22,.37 9 S CI 1 1/4 1.22,.37,.45, S Br, CI 1 1/2 1 1/4.37,.45, S Br, CI 2 1 1/2.45,.58, S CI 3 2 1/2 1.16, Chemflo SS 1 1/2 1.22, CF SS 1 1/2 1.22, CF SS 2 1 1/2.22, CF SS 2 1 1/2.22, CF SS 2 1 1/2 1.16, CF SS , CF SS , CF SS 3 1 1/ SUBMERSIBLE HydraSub Al N/A 2.22,.37,.45 9 HS Al N/A 2 1/2.37,.45, HS Al N/A 3.45, MP PUMPS, INC. PHONE: (800) FAX: (586)

6 Determine Hydraulic Motor Drive Motor drive matrix Pump Model Hydraulic Assembly Type Max Motor flow (gpm) Max Press. (psi) Perf. Curve No. Motor Type Inlet Size Outlet Size Motor Size (cuin/rev) Bi- Rotation Y/N Flow Cont. option Y/N SELF PRIMING PUMPS Flomax S 0.37 Pedestal S S Gerotor SAE 8 SAE 8 Y Y Flomax 8 Pedestal S 0.37 Hy Speed S Pedestal S 0.45 Hy Speed S Pedestal S 0.58 Hy Speed S Flomax Pedestal Gear SAE 10 Flomax Pedestal Gear SAE 10 HHLF Pedestal Gear SAE 10 HHLF Pedestal Gear SAE 10 2CT END SUCTION PUMPS Hy Speed Gerotor SAE 8 SAE 8 Y Y Gerotor SAE 8 SAE 8 Y Y Gerotor SAE 8 SAE 8 Y Y SAE 10 SAE 10 SAE 10 SAE Gerotor SAE 8 SAE 8 Y Y Y Y Y Y N N N N Series S Pedestal S Gerotor SAE 8 SAE 8 Y Y S S 0.37 Hy S 0.45 Speed S S Gerotor SAE 8 SAE 8 Y Y S80 Pedestal S Gerotor SAE 8 SAE 8 Y Y 0.37 Hy Speed S Gerotor SAE 8 SAE 8 Y Y Pedestal S 0.45 Hy Speed S Pedestal S 0.58 Hy Speed S Gerotor SAE 8 SAE 8 Y Y Gerotor SAE 8 SAE 8 Y Y 3 MP PUMPS, INC. PHONE: (800) FAX: (586)

7 Pump Model END SUCTION PUMPS S Hydraulic Assembly Type Hy Speed Hy Speed Max Motor flow (gpm) Max Press. (psi) Perf. Curve No. Motor Type Inlet Size Outlet Size Motor Size (cuin/rev) Bi- Rotation Y/N Flow Cont. option Y/N S Gerotor SAE 8 SAE 8 N Y S Gerotor SAE 8 SAE 8 N Y 0.73 Pedestal Gear SAE 10 S S Gear SAE 12 Pedestal S Gear SAE 12 Chemflo Hy S 0.37 Speed S SAE 10 SAE 12 SAE 12 Gerotor SAE 8 SAE 8 Y Y Y Y Y N N N CF Hy S 0.37 Speed S CF Hy S 0.37 Speed S Gerotor SAE 8 SAE 8 Y Y Gerotor SAE 8 SAE 8 Y Y CF Hy S 0.37 Speed S CF Gear SAE 12 Pedestal Gear SAE 12 CF Gear SAE 12 Pedestal Gear SAE 12 CF Gear SAE 12 Pedestal Gear SAE 12 CF Pedestal Gear SAE 12 SUBMERSIBLE PUMPS Gerotor SAE 8 SAE 8 Y Y HydraSub N/A S Gerotor SAE 8 SAE 8 Y Y SAE 12 SAE 12 SAE 12 SAE 12 SAE 12 SAE 12 SAE N/A S Gerotor SAE 8 SAE 8 Y Y 0.45 N/A S Gerotor SAE 8 SAE 8 Y Y HS N/A S Gerotor SAE 8 SAE 8 Y Y 0.58 N/A Gerotor SAE 8 SAE 8 Y Y HS N/A S Gerotor SAE 8 SAE 8 Y Y 0.58 N/A S Gerotor SAE 8 SAE 8 Y Y Y Y Y Y Y Y Y N N N N N N N 4 MP PUMPS, INC. PHONE: (800) FAX: (586)

8 Gerotor Hydraulic Motor Options Gerotor motors are available in the G3 Hydraulic Pedestal or the HySpeed Pedestal (excludes the HydraSub). All gerotor motors have a patented case drain option that is plugged and can be used by removing the plug and connecting to the open port. Flow control option is pressure compensated and available for right hand rotation only (cannot be applied to left hand pumps or HydraSub). The flow control will allow 10 gpm of oil flow maximum to be bypassed. When to select a HySpeed drive. 1. Unusually high oil pressure/oil flow required and/or very low pump flow rate. 2. Bi-rotational is not required. 3. Flow control (open center) is not required. MP Gerotor Series Feature Pedestal HySpeed HydraSub Bi-rotational Y N Ynr Case Drain** Y Y Y Flow Control Optional* Optional NA Pressure Relief Valve Optional* Optional N Cast Iron Construction Y Y Y Single Shaft Design Y Y Y Seal (double/single) D S D Ports SAE Y Y Y Displacements Offered Pump/motor rotation R/L* RH LH Seal rating PSI Pressure Diff. Max PSI * Flow control and Pressure relief valve are available for RH only **Motors are normally supplied with the case drain plugged Motor Selection Hydraulic System Types There are three types of hydraulic systems: Open Center-OC, Closed Center pressure compensated- CCpc, and Closed Center load sensing CCls. The hydraulic motor selection must match the system to be compatible. Open Center OC Identified by oil flowrate This hydraulic system is made for a constant oil flow at a specific amount. The hydraulic motor must match the oil flow rate. If it does not match some of the oil must be bypassed around the motor by using a motor with a flow control. The best motor selection is to use the largest displacement as possible. This will minimize the oil that is bypassed and operated most efficiently. All OC systems must have motors with a flow control or have motors sized exactly to match the flow rate. Wherever possible use the largest motor displacement possible. A motor with a flow control may bypass up to 10 gpm of oil. Closed Center pressure compensated CCpc Identified by oil pressure This hydraulic system is made for delivering constant oil pressure. The hydraulic motor must be sized to match the system pressure. If the system pressure is higher than any motor performance curve offering an orifice must be used prior to the motor to reduce the pressure to the motor. The orifice is not available thru MP Pumps. This system is the most difficult to regulate for a centrifugal pump load where several orifices may need to be tested to achieve the correct size. Select the smallest motor displacement possible. A motor with a flow control should not be used. 5 MP PUMPS, INC. PHONE: (800) FAX: (586)

9 Closed Center load sensing CCls Identified by oil pressure and load sense This system senses load and when the load is reduced the flow will be reduced to maintain a set pressure. The initial set-up fixes the hydraulic pressure to match the motor requirements where an orifice and a flow control is not needed. The motor should be sized close to the system pressure but the flow will be limited as well making the motor displacement selection not as critical. Pump/Motor Detail Pump Model SELF PRIMING PUMPS Material of Const. Discharge Orientation Motor Disp. (cuin/rev) Hyd. Asy. Type Motor Type Flow Control Y/N Part No. Perf. Curve No. Install. Drawing Service List No. Flomax 5 Y CI Vertical 0.22 Pedestal Gerotor CN 7126-S N CI Vertical 0.37 Pedestal Gerotor CI Vertical 0.45 Pedestal Gerotor Y CN 7088-S N Y CN 7089-S N Flomax 8 Y CI Vertical 0.37 Pedestal Gerotor CN 7090-S N CI Vertical 0.37 Hy Speed Gerotor CI Vertical 0.45 Pedestal Gerotor CI Vertical 0.45 Hy Speed Gerotor CI Vertical 0.58 Pedestal Gerotor CI Vertical 0.58 Hy Speed Gerotor Flomax 10 Br Vertical 0.73 Gear N Pedestal CI Vertical 0.73 Gear N Flomax 15 Br Vertical 0.73 Gear N Pedestal CI Vertical 0.73 Gear N HHLF1.5 Br Vertical Pedestal Gear N CI Vertical HHLF2.0 Br Vertical Pedestal Gear N CI Vertical CT-3 CI Vertical 0.58 Hy Speed Y CN 7093-S N Y CN 7091-S N Y CN 7094-S N Y CN 7092-S N Y CN 7095-S N CN CN CN CN Gerotor N CN MP PUMPS, INC. PHONE: (800) FAX: (586)

10 Pump Model END SUCTION PUMPS Material of Const. Discharge Orientation Motor Disp. (cuin/rev) Hyd. Asy. Type Motor Type Flow Control Y/N Part No. Perf. Curve No. Install. Drawing Service List No. Series 30 Y CI Horizontal 0.22 Pedestal Gerotor CN 7120-S N CI Horizontal 0.37 Pedestal Gerotor Y CN 7085-S N S60 Hy Y CI Horizontal 0.22 Gerotor CN 7121-S Speed N CI Horizontal 0.37 CI Horizontal 0.45 CI Horizontal 0.58 Hy Speed Hy Speed Hy Speed Gerotor Gerotor Gerotor Y CN 7102-S N Y CN 7101-S N Y CN 7122-S N S80 Y CI Horizontal 0.37 Pedestal Gerotor CN 7129-S N CI Horizontal 0.37 Hy Speed Gerotor CI Horizontal 0.45 Pedestal Gerotor CI Horizontal 0.45 Hy Speed Gerotor CI Horizontal 0.58 Pedestal Gerotor CI Horizontal 0.58 Hy Speed Gerotor Y CN 7103-S N Y CN 7086-S N Y CN 7104-S N Y CN 7087-S N Y CN 7105-S N S120 Hy Y CI Horizontal 0.45 Gerotor CN 7107-S Speed N CI Horizontal 0.58 Hy Speed Gerotor Br Horizontal 0.73 Pedestal Gear N CI Y CN 7108 N CN S300 CI Horizontal 1.16 Gear N CN 7041 Pedestal CI Horizontal 1.59 Gear N CN MP PUMPS, INC. PHONE: (800) FAX: (586)

11 Pump Model END SUCTION PUMPS Material of Const. Discharge Orientation Motor Disp. (cuin/rev) Hyd. Asy. Type Motor Type Flow Control Y/N Part No. Perf. Curve No. Install. Drawing Service List No. Chemflo Hy Y Vertical 0.22 Gerotor CN 7113-S SS Speed N SS Vertical 0.37 Hy Speed Gerotor Y N CN 7109-S CF Hy Y Vertical 0.22 Gerotor CN 7128-S SS Speed N SS Vertical 0.37 Hy Speed Gerotor Y CN 7110-S N CF Hy Y Vertical 0.22 Gerotor CN 7114-S SS Speed N SS Vertical 0.37 Hy Speed Gerotor Y CN 7111-S N CF Hy Y Vertical 0.22 Gerotor CN 7115-S SS Speed N SS Vertical 0.37 Hy Speed Gerotor Y CN 7112-S N CF CN Vertical Pedestal Gear N SS CN CF CN Vertical Pedestal Gear N SS CN CF CN Vertical Pedestal Gear N SS CN CF 8 SUBMERSIBLE HydraSub SS Vertical 1.59 Pedestal Gear N CN Al Vertical 0.22 N/A Gerotor N CN 7117-S Al Vertical 0.37 N/A Gerotor N CN 7096-S Al Vertical 0.45 N/A Gerotor N CN 7098-S HS 25 Al Vertical 0.45 N/A Gerotor N CN 7099-S Al Vertical 0.58 N/A Gerotor N CN 7072 HS 30 Al Vertical 0.45 N/A Gerotor N CN 7100-S Al Vertical 0.58 N/A Gerotor N CN 7118-S MP PUMPS, INC. PHONE: (800) FAX: (586)

12 Comparison with Ace and Hypro Feature MP PUMPS* HYPRO ACE Bi-rotational Y N N Reverse Check NR R R Orifice Limit NA R R Case Drain Y N N Flow Control Ball/sp(op)** Needle Needle Pressure Relief Valve Y(op) N N Gerotor Y Y N Cast Iron Construction Y Y Y Single Shaft Design Y Y N Seal (double/single) D S S Ports (SAE/NPT) SAE 8 NPT NPT Displacements Offered Pump/motor rotation RH/LH*** LH LH Seal rating PSI Pressure Diff. Max PSI *Pedestal features Bi-rotational, case drain when not plugged (a patentable feature), cast iron, gerotor, flow control/pressure relief valve, with oil lubed bearings. ** Flow control is pressure compensating via ball and spring design that is optional. *** Left hand rotation limited availability based upon the pump offered. Op= optional 9 MP PUMPS, INC. PHONE: (800) FAX: (586)

13 10 MP PUMPS, INC. PHONE: (800) FAX: (586)

14 Hydraulic Drive & Pump Selection When selecting the best pump and motor for the application use this to guide you to the proper fit. In some cases there may be multiple solutions because of overlap in product. Information Required (minimum) Centrifugal pump GPM Pump flow rate expected PSI Discharge pressure Y/N Self priming requirement Hydraulic System One of three systems 1. Open Center- Usually stated as open and always rated for flow rate. GPM Oil flow rate 2. Closed Center- Load Sensing (Closed-LS) GPM Oil flow rate (max) PSI Oil system hydraulic pressure (max) 3. Closed Center- Pressure Compensating (Closed-PC) PSI Oil system hydraulic pressure GPM Oil flow rate (max) Determine Best Fit Select the pump based upon the hydraulic curves or the Hypro/Ace pump cross reference. In some cases the discharge of the pump can be used. Select the motor by the system type and oil flow/pressure. 1. Open Center Systems The motor must have a flow control. Select the largest motor possible to match the oil flow rate. Whenever the flow rate exceeds the motor range the flow control will allow up to 10 GPM bypass. 2. Closed Center (LS) The motor should not have a flow control. Select the motor size based upon flow rate to be smaller than the maximum oil system flow rate. If a smaller motor is available and the pressure requirement is within range use the smaller motor. 3. Closed Center (PC) The motor should not have a flow control. Select the smallest motor to match the motor pressure and the system pressure. If the pressure difference is greater than 400 psi (system-pump curve) an orifice will be required to limit hydraulic flow and we will not recommend the use of our pump. When in doubt consult the factory. 11 MP PUMPS, INC. PHONE: (800) FAX: (586)

15 HYDRAULIC SUBASSEMBLY FEATURES 12 MP PUMPS, INC. PHONE: (800) FAX: (586)

16 FLOMAX Performance - Pedestal 13 MP PUMPS, INC. PHONE: (800) FAX: (586)

17 FLOMAX Performance - Pedestal 14 MP PUMPS, INC. PHONE: (800) FAX: (586)

18 FLOMAX Performance - Pedestal 15 MP PUMPS, INC. PHONE: (800) FAX: (586)

19 FLOMAX Performance - Pedestal 16 MP PUMPS, INC. PHONE: (800) FAX: (586)

20 FLOMAX Performance - Pedestal 17 MP PUMPS, INC. PHONE: (800) FAX: (586)

21 FLOMAX Performance - Pedestal 18 MP PUMPS, INC. PHONE: (800) FAX: (586)

22 FLOMAX Dimensions - Pedestal 19 MP PUMPS, INC. PHONE: (800) FAX: (586)

23 FLOMAX 5 Exploded View Pedestal With Flow Control 20 MP PUMPS, INC. PHONE: (800) FAX: (586)

24 FLOMAX 8 Exploded Views Pedestal With Flow Control 21 MP PUMPS, INC. PHONE: (800) FAX: (586)

25 FLOMAX 8 Exploded Views Pedestal With Flow Control 22 MP PUMPS, INC. PHONE: (800) FAX: (586)

26 FLOMAX 5 Exploded Views - Pedestal 23 MP PUMPS, INC. PHONE: (800) FAX: (586)

27 FLOMAX Performance HY Speed 24 MP PUMPS, INC. PHONE: (800) FAX: (586)

28 FLOMAX Performance HY Speed 25 MP PUMPS, INC. PHONE: (800) FAX: (586)

29 FLOMAX Performance HY Speed 26 MP PUMPS, INC. PHONE: (800) FAX: (586)

30 FLOMAX Dimensions HY Speed 27 MP PUMPS, INC. PHONE: (800) FAX: (586)

31 FLOMAX 8 Exploded View HY Speed With Flow Control 28 MP PUMPS, INC. PHONE: (800) FAX: (586)

32 FLOMAX 8 Exploded View HY Speed 29 MP PUMPS, INC. PHONE: (800) FAX: (586)

33 FLOMAX Performance 30 MP PUMPS, INC. PHONE: (800) FAX: (586)

34 FLOMAX Dimensions 31 MP PUMPS, INC. PHONE: (800) FAX: (586)

35 FLOMAX 10 Exploded View 32 MP PUMPS, INC. PHONE: (800) FAX: (586)

36 FLOMAX 10 Exploded View Bronze Impeller 33 MP PUMPS, INC. PHONE: (800) FAX: (586)

37 FLOMAX 15 Exploded View 34 MP PUMPS, INC. PHONE: (800) FAX: (586)

38 FLOMAX 15 Exploded View Bronze Impeller 35 MP PUMPS, INC. PHONE: (800) FAX: (586)

39 FLOMAX 15 Exploded View Stainless Impeller 36 MP PUMPS, INC. PHONE: (800) FAX: (586)

40 FLOMAX 15 Exploded View Ni-Resist Seal 37 MP PUMPS, INC. PHONE: (800) FAX: (586)

41 FLOMAX 15 Exploded View Stainless Pump Ni-Resist Seal 38 MP PUMPS, INC. PHONE: (800) FAX: (586)

42 HHLF & 2CT Performance 39 MP PUMPS, INC. PHONE: (800) FAX: (586)

43 HHLF & 2CT Performance 40 MP PUMPS, INC. PHONE: (800) FAX: (586)

44 HHLF & 2CT Performance 41 MP PUMPS, INC. PHONE: (800) FAX: (586)

45 HHLF & 2CT Dimensions 42 MP PUMPS, INC. PHONE: (800) FAX: (586)

46 HHLF & 2CT Dimensions 43 MP PUMPS, INC. PHONE: (800) FAX: (586)

47 HHLF 2CT-3 & 2CT Exploded View With Flow Control 44 MP PUMPS, INC. PHONE: (800) FAX: (586)

48 HHLF 2CT-3 & 2CT Exploded View 45 MP PUMPS, INC. PHONE: (800) FAX: (586)

49 HHLF 2.0 Exploded View Bronze Impeller 46 MP PUMPS, INC. PHONE: (800) FAX: (586)

50 HHLF 1.5 Exploded View 47 MP PUMPS, INC. PHONE: (800) FAX: (586)

51 HHLF 2.0 Exploded View Bronze 48 MP PUMPS, INC. PHONE: (800) FAX: (586)

52 HHLF 2.0 Exploded View 49 MP PUMPS, INC. PHONE: (800) FAX: (586)

53 SERIES Performance - Pedestal 50 MP PUMPS, INC. PHONE: (800) FAX: (586)

54 SERIES Performance - Pedestal 51 MP PUMPS, INC. PHONE: (800) FAX: (586)

55 SERIES Performance - Pedestal 52 MP PUMPS, INC. PHONE: (800) FAX: (586)

56 SERIES Performance - Pedestal 53 MP PUMPS, INC. PHONE: (800) FAX: (586)

57 SERIES Performance - Pedestal 54 MP PUMPS, INC. PHONE: (800) FAX: (586)

58 Series Dimensions - Pedestal 55 MP PUMPS, INC. PHONE: (800) FAX: (586)

59 Series Dimensions - Pedestal 56 MP PUMPS, INC. PHONE: (800) FAX: (586)

60 Series 3.0 Exploded View Pedestal With Flow Control 57 MP PUMPS, INC. PHONE: (800) FAX: (586)

61 Series 3.0 Exploded View Pedestal 58 MP PUMPS, INC. PHONE: (800) FAX: (586)

62 Series 80 Exploded View Pedestal With Flow Control 59 MP PUMPS, INC. PHONE: (800) FAX: (586)

63 Series 80 Exploded View Pedestal 60 MP PUMPS, INC. PHONE: (800) FAX: (586)

64 Series Performance HY Speed 61 MP PUMPS, INC. PHONE: (800) FAX: (586)

65 Series Performance HY Speed 62 MP PUMPS, INC. PHONE: (800) FAX: (586)

66 Series Performance HY Speed 63 MP PUMPS, INC. PHONE: (800) FAX: (586)

67 Series Performance HY Speed 64 MP PUMPS, INC. PHONE: (800) FAX: (586)

68 Series Performance HY Speed 65 MP PUMPS, INC. PHONE: (800) FAX: (586)

69 Series Performance HY Speed 66 MP PUMPS, INC. PHONE: (800) FAX: (586)

70 Series Performance HY Speed 67 MP PUMPS, INC. PHONE: (800) FAX: (586)

71 Series Performance HY Speed 68 MP PUMPS, INC. PHONE: (800) FAX: (586)

72 Series Performance HY Speed 69 MP PUMPS, INC. PHONE: (800) FAX: (586)

73 Series Dimensions HY Speed 70 MP PUMPS, INC. PHONE: (800) FAX: (586)

74 Series Dimensions HY Speed 71 MP PUMPS, INC. PHONE: (800) FAX: (586)

75 Series Dimensions HY Speed 72 MP PUMPS, INC. PHONE: (800) FAX: (586)

76 Series 60 Exploded View HY Speed With Flow Control 73 MP PUMPS, INC. PHONE: (800) FAX: (586)

77 Series 80 Exploded View HY Speed 74 MP PUMPS, INC. PHONE: (800) FAX: (586)

78 Series 80 Exploded View HY Speed With Flow Control 75 MP PUMPS, INC. PHONE: (800) FAX: (586)

79 Series 80 Exploded View HY Speed 76 MP PUMPS, INC. PHONE: (800) FAX: (586)

80 Series 120 Exploded View HY Speed With Flow Control 77 MP PUMPS, INC. PHONE: (800) FAX: (586)

81 Series 120 Exploded View HY Speed 78 MP PUMPS, INC. PHONE: (800) FAX: (586)

82 Series Performance 79 MP PUMPS, INC. PHONE: (800) FAX: (586)

83 Series Dimensions 80 MP PUMPS, INC. PHONE: (800) FAX: (586)

84 Series 120 Exploded View 81 MP PUMPS, INC. PHONE: (800) FAX: (586)

85 Series 120 Exploded View Bronze Pump 82 MP PUMPS, INC. PHONE: (800) FAX: (586)

86 Series Performance 83 MP PUMPS, INC. PHONE: (800) FAX: (586)

87 Series Performance 84 MP PUMPS, INC. PHONE: (800) FAX: (586)

88 Series Dimensions 85 MP PUMPS, INC. PHONE: (800) FAX: (586)

89 SERIES 300 Exploded View With 1.16 Disp. Motor 86 MP PUMPS, INC. PHONE: (800) FAX: (586)

90 SERIES 300 Exploded View With 1.59 Disp. Motor 87 MP PUMPS, INC. PHONE: (800) FAX: (586)

91 CHEMFLO Performance HY Speed 88 MP PUMPS, INC. PHONE: (800) FAX: (586)

92 CHEMFLO Performance HY Speed 89 MP PUMPS, INC. PHONE: (800) FAX: (586)

93 CHEMFLO Performance HY Speed 90 MP PUMPS, INC. PHONE: (800) FAX: (586)

94 CHEMFLO Performance HY Speed 91 MP PUMPS, INC. PHONE: (800) FAX: (586)

95 CHEMFLO Performance HY Speed 92 MP PUMPS, INC. PHONE: (800) FAX: (586)

96 CHEMFLO Performance HY Speed 93 MP PUMPS, INC. PHONE: (800) FAX: (586)

97 CHEMFLO Performance HY Speed 94 MP PUMPS, INC. PHONE: (800) FAX: (586)

98 CHEMFLO Performance HY Speed 95 MP PUMPS, INC. PHONE: (800) FAX: (586)

99 CHEMFLO Dimensions HY Speed 96 MP PUMPS, INC. PHONE: (800) FAX: (586)

100 CHEMFLO Dimensions HY Speed 97 MP PUMPS, INC. PHONE: (800) FAX: (586)

101 CHEMFLO 1-2 Exploded View HY Speed With Flow Control 98 MP PUMPS, INC. PHONE: (800) FAX: (586)

102 CHEMFLO 3-4 Exploded View HY Speed With Flow Control 99 MP PUMPS, INC. PHONE: (800) FAX: (586)

103 CHEMFLO 1-2 Exploded View HY Speed 100 MP PUMPS, INC. PHONE: (800) FAX: (586)

104 CHEMFLO 3-4 Exploded View HY Speed 101 MP PUMPS, INC. PHONE: (800) FAX: (586)

105 CHEMFLO Performance 102 MP PUMPS, INC. PHONE: (800) FAX: (586)

106 CHEMFLO Performance 103 MP PUMPS, INC. PHONE: (800) FAX: (586)

107 CHEMFLO Performance 104 MP PUMPS, INC. PHONE: (800) FAX: (586)

108 CHEMFLO Performance 105 MP PUMPS, INC. PHONE: (800) FAX: (586)

109 CHEMFLO Performance 106 MP PUMPS, INC. PHONE: (800) FAX: (586)

110 CHEMFLO Performance 107 MP PUMPS, INC. PHONE: (800) FAX: (586)

111 CHEMFLO Performance 108 MP PUMPS, INC. PHONE: (800) FAX: (586)

112 CHEMFLO Dimensions 109 MP PUMPS, INC. PHONE: (800) FAX: (586)

113 CHEMFLO Dimensions 110 MP PUMPS, INC. PHONE: (800) FAX: (586)

114 CHEMFLO Dimensions 111 MP PUMPS, INC. PHONE: (800) FAX: (586)

115 CHEMFLO Dimensions 112 MP PUMPS, INC. PHONE: (800) FAX: (586)

116 CHEMFLO 5 Exploded View With 1.16 Disp. Motor 113 MP PUMPS, INC. PHONE: (800) FAX: (586)

117 CHEMFLO 5 Exploded View With 1.59 Disp. Motor 114 MP PUMPS, INC. PHONE: (800) FAX: (586)

118 CHEMFLO 6 Exploded View With 1.16 Disp. Motor 115 MP PUMPS, INC. PHONE: (800) FAX: (586)

119 CHEMFLO 6 Exploded View With 1.59 Disp. Motor 116 MP PUMPS, INC. PHONE: (800) FAX: (586)

120 CHEMFLO 6 Exploded View With 1.59 Disp. Motor and Severe Service Seal 117 MP PUMPS, INC. PHONE: (800) FAX: (586)

121 CHEMFLO 7 Exploded View With 1.16 Disp. Motor and Severe Service Seal 118 MP PUMPS, INC. PHONE: (800) FAX: (586)

122 CHEMFLO 7 Exploded View With 1.59 Disp. Motor and Severe Service Seal 119 MP PUMPS, INC. PHONE: (800) FAX: (586)

123 CHEMFLO 8 Exploded View 120 MP PUMPS, INC. PHONE: (800) FAX: (586)

124 HYDRASUB Performance 121 MP PUMPS, INC. PHONE: (800) FAX: (586)

125 HYDRASUB Performance 122 MP PUMPS, INC. PHONE: (800) FAX: (586)

126 HYDRASUB Performance 123 MP PUMPS, INC. PHONE: (800) FAX: (586)

127 HYDRASUB Performance 124 MP PUMPS, INC. PHONE: (800) FAX: (586)

128 HYDRASUB Performance 125 MP PUMPS, INC. PHONE: (800) FAX: (586)

129 HYDRASUB Performance 126 MP PUMPS, INC. PHONE: (800) FAX: (586)

130 HYDRASUB Performance 127 MP PUMPS, INC. PHONE: (800) FAX: (586)

131 HYDRASUB Performance 128 MP PUMPS, INC. PHONE: (800) FAX: (586)

132 HYDRASUB Performance 129 MP PUMPS, INC. PHONE: (800) FAX: (586)

133 HYDRASUB Dimensions 130 MP PUMPS, INC. PHONE: (800) FAX: (586)

134 HYDRASUB Dimensions 131 MP PUMPS, INC. PHONE: (800) FAX: (586)

135 HYDRASUB 20 Exploded View.22 Disp. Motor 132 MP PUMPS, INC. PHONE: (800) FAX: (586)

136 HYDRASUB 20 Exploded View.37 Disp. Motor 133 MP PUMPS, INC. PHONE: (800) FAX: (586)

137 HYDRASUB 20 Exploded View.45 Disp. Motor 134 MP PUMPS, INC. PHONE: (800) FAX: (586)

138 HYDRASUB 25 Exploded View.45 Disp. Motor 135 MP PUMPS, INC. PHONE: (800) FAX: (586)

139 HYDRASUB 30 Exploded View.58 Disp. Motor 136 MP PUMPS, INC. PHONE: (800) FAX: (586)

140 HYDRASUB 30 Exploded View.58 Disp. Motor 137 MP PUMPS, INC. PHONE: (800) FAX: (586)

141 HYDRAULIC Dimensions - Pedestal 138 MP PUMPS, INC. PHONE: (800) FAX: (586)

142 HYDRAULIC Exploded View Pedestal.22 Disp. Motor With Flow Control 139 MP PUMPS, INC. PHONE: (800) FAX: (586)

143 HYDRAULIC Exploded View Pedestal.22 Disp. Motor 140 MP PUMPS, INC. PHONE: (800) FAX: (586)

144 HYDRAULIC Exploded View Pedestal.37 Disp. Motor With Flow Control 141 MP PUMPS, INC. PHONE: (800) FAX: (586)

145 HYDRAULIC Exploded View Pedestal.37 Disp. Motor 142 MP PUMPS, INC. PHONE: (800) FAX: (586)

146 HYDRAULIC Exploded View Pedestal.45 Disp. Motor With Flow Control 143 MP PUMPS, INC. PHONE: (800) FAX: (586)

147 HYDRAULIC Exploded View Pedestal.45 Disp. Motor 144 MP PUMPS, INC. PHONE: (800) FAX: (586)

148 HYDRAULIC Exploded View Pedestal.58 Disp. Motor With Flow Control 145 MP PUMPS, INC. PHONE: (800) FAX: (586)

149 HYDRAULIC Exploded View Pedestal.58 Disp. Motor 146 MP PUMPS, INC. PHONE: (800) FAX: (586)

150 HYDRAULIC Dimensions HY Speed 147 MP PUMPS, INC. PHONE: (800) FAX: (586)

151 HYDRAULIC Dimensions HY Speed 148 MP PUMPS, INC. PHONE: (800) FAX: (586)

152 HYDRAULIC Exploded View HY Speed.22 Disp. Motor With Flow Control 149 MP PUMPS, INC. PHONE: (800) FAX: (586)

153 HYDRAULIC Exploded View HY Speed.22 Disp. Motor 150 MP PUMPS, INC. PHONE: (800) FAX: (586)

154 HYDRAULIC Exploded View HY Speed.37 Disp. Motor With Flow Control 151 MP PUMPS, INC. PHONE: (800) FAX: (586)

155 HYDRAULIC Exploded View HY Speed.37 Disp. Motor With Flow Control 152 MP PUMPS, INC. PHONE: (800) FAX: (586)

156 HYDRAULIC Exploded View HY Speed.37 Disp. Motor 153 MP PUMPS, INC. PHONE: (800) FAX: (586)

157 HYDRAULIC Exploded View HY Speed.37 Disp. Motor 154 MP PUMPS, INC. PHONE: (800) FAX: (586)

158 HYDRAULIC Exploded View HY Speed.45 Disp. Motor With Flow Control 155 MP PUMPS, INC. PHONE: (800) FAX: (586)

159 HYDRAULIC Exploded View HY Speed.45 Disp. Motor With Flow Control 156 MP PUMPS, INC. PHONE: (800) FAX: (586)

160 HYDRAULIC Exploded View HY Speed.45 Disp. Motor 157 MP PUMPS, INC. PHONE: (800) FAX: (586)

161 HYDRAULIC Exploded View HY Speed.45 Disp. Motor 158 MP PUMPS, INC. PHONE: (800) FAX: (586)

162 HYDRAULIC Exploded View HY Speed.58 Disp. Motor With Flow Control 159 MP PUMPS, INC. PHONE: (800) FAX: (586)

163 HYDRAULIC Exploded View HY Speed.58 Disp. Motor With Flow Control 160 MP PUMPS, INC. PHONE: (800) FAX: (586)

164 HYDRAULIC Exploded View HY Speed.58 Disp. Motor 161 MP PUMPS, INC. PHONE: (800) FAX: (586)

165 HYDRAULIC Exploded View HY Speed.58 Disp. Motor 162 MP PUMPS, INC. PHONE: (800) FAX: (586)

166 HYDRAULIC Dimensions HY Speed 163 MP PUMPS, INC. PHONE: (800) FAX: (586)

167 HYDRAULIC Exploded View 164 MP PUMPS, INC. PHONE: (800) FAX: (586)