The Advantage Series. Pump & Dispenser Specifications MDE-3807A

Transcription

1 The Advantage Series Pump & Dispenser Specifications MDE-3807A

2 Computer Programs and Documentation All Gilbarco Inc. computer programs (including software on diskettes and within memory chips) and documentation are copyrighted by, and shall remain the property of, Gilbarco Inc. Such computer programs and documents may also contain trade secret information. The duplication, disclosure, modification, or unauthorized use of computer programs or documentation is strictly prohibited, unless otherwise licensed by Gilbarco Inc. FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate this equipment. Approvals Gilbarco is an ISO 9001:2000 registered company. Underwriters Laboratories: New York City: U. L. File# Products listed with U. L. NYFD C of A # MH1941 All Gilbarco pumps and dispensers that bear the U.L. listing mark. MH8467 Transac System 1000 and PAM 1000 E Dell DHM Minitower E G-SITE and Passport Systems NCWM - Certificate of Compliance: Gilbarco pumps and dispensers are evaluated by the National Conference of Weights and Measures (NCWM) under the National Type Evaluation Program (NTEP). NCWM has issued the following Certificates of Compliance (COC): COC# Product Model # COC# Product Model # COC# Product Model # Eclipse Exx H111B Series AC, RAC External Mount CRIND CECXXXXXXX Encore Nxx MPD-1 Series AN, RAN Dimension Dxx AF, RAF, AG, T-12C Console PA0188, RA Fixed Blender RAG Legacy Jxxx T-12C Console PA0203, RA0203 Dispenser - Low Profile AR, RAR G-SITE Printer (Epson) PA T-12G Console PA0180, RA0180 Indoor Card Q11640 G-SITE Distribution Box PA T-15 Console PA0189 Outdoor Card Q11891 G-SITE Keyboard PA T-15 Controller C2 PA CRIND G-SITE Mini Tower PA0301 T-15 Controller PA0190 TS-1000 Console PA0240 G-SITE Monitor PA0303 ProBlender AU, RAU TS-1000 Controller PA0241 G-SITE Printer (Citizen) PA0308 Precision Blender AE, RAE Distribution Box PA C+ Meter T Dispenser - Standard AK, RAK Micro-T Console PA Passport PA0324 Dispenser - Low Profile AL, RAL Meter - EC Series PA024EC Ecometer T20453 Fixed Blender AP, RAF VaporVac Kits CV Meter - C Series PA024NC The Advantage Series Bxx, RBxx Meter - C Series PA024TC Trimline Series AA, RAA Salesmaker ProBlender AB, RAB Meter - C Series PA024XC Salesmaker Series 2/2H/4/4A AM MPD-A3 Series AD, RAD Patents Gilbarco Inc. products are manufactured or sold under one or more of the following U.S. patents.: Dispensers 4,566,504 4,556,927 4,570,686 4,687,033 4,728,788 4,748,846 4,781,066 4,793,589 4,799,940 4,805,453 4,876,653 4,890,210 4,913,813 4,930,665 4,934,565 4,938,054 4,938,251 4,939,730 4,967,366 4,978,029 4,986,445 5,013,434 5,029,100 5,040,577 5,083,846 5,098,179 5,099,403 5,110,010 5,134,548 5,156,199 5,269,353 5,228,084 5,325,706 5,345,979 5,355,915 5,363,988 5,384,850 5,407,115 5,417,256 5,448,638 5,561,715 5,450,883 5,452,750 5,464,466 5,493,315 5,501,246 5,514,933 5,515,390 5,535,130 5,542,458 5,543,849 5,546,981 5,557,084 5,571,310 5,592,979 5,602,745 5,561,715 5,602,745 5,626,649 5,630,528 5,708,580 5,719,779 5,719,781 5,720,325 5,724,067 5,734,851 5,755,854 5,782,275 5,794,667 5,798,931 5,803,136 5,843,212 5,857,500 5,868,179 5,871,651 5,890,520 5,898,141 5,954,080 5,956,259 5,969,691 5,971,042 5,979,705 5,980,090 5,992,395 5,996,888 6,026,866 6,026,868 6,032,126 6,052,629 6,054,940 6,062,473 6,065,507 6,065,638 6,067,476 6,070,156 6,073,840 6,078,888 6,078,896 6,082,415 6,085,775 6,087,954 6,092,410 6,098,879 6,102,085 6,116,505 6,119,110 6,123,118 6,149,033 6,157,871 6,170,539 6,176,421 6,184,846 6,185,307 6,185,893 6,196,065 6,227,227 6,244,310 6,250,151 6,253,779 6,263,319 6,275,746 6,296,148 6,302,165 6,313,737 6,325,112 6,326,934 6,336,479 6,338,369 6,347,649 6,352,176 6,357,493 6,360,137 6,363,299 6,364,206 RE35,238 D262,971 D265,092 D306,719 D309,144 D316,471 D413,124 D413,311 D413,336 D413,337 D413,610 D413,901 D413,902 D414,192 D414,501 D414,778 D414,779 D414,780 D414,781 D414,782 D415,166 D415,167 D415,168 D415,169 D415,170 D415,171 D415,172 D415,501 D415,777 D416,915 D416,916 D417,226 D418,523 D420,684 D421,612 D422,285 D422,604 D426,555 D428,424 D428,897 D429,739 D429,740 D432,140 D432,548 D432,552 D433,032 D433,033 D433,034 D433,035 D433,036 D433,037 D433,685 D433,686 D435,051 D440,579 D443,624 Point of Sale/Back Office Equipment 4,967,366 5,228,084 5,448,638 5,561,715 5,798,931 5,980,090 5,493,315 5,708,580 5,719,779 5,719,781 5,724,067 5,734,851 6,032,126 6,067,527 6,073,840 6,078,888 6,116,505 6,185,307 6,263,319 6,275,746 6,326,934 6,360,137 6,363,299 6,364,206 Trademarks Non-registered trademarks C-PAM G-SITE Lite Surge Management System ECR Highline Tank Monitor EMC MultiLine TCR G-CAT Optimum Series Ultra-Hi Gilbert PAM 1000 ValueLine G-Poll Interface PAM SmartPad SMART Connect Product 4805 The Advantage Series and Legacy Series 4986 Encore and Eclipse Registered trademarks Dimension Series The Advantage Series Eclipse Gilbarco Transac TRIND InfoScreen Trimline Passport Legacy VaporVac CRIND Making Things Better G-SITE Performer MPD Transac System 1000 InfoScreen GOLD Encore California Air Resources Board (CARB): Executive Order # Product G Balance Vapor Recovery G AB VaporVac Additional U.S. and foreign patents pending. Additional U.S. and foreign trademarks pending. Other brand or product names shown may be trademarks or registered trademarks of their respective holders. This document is subject to change without notice. For information regarding Gilbarco Inc. Literature, call (336) literature@gilbarco.com Internet: Gilbarco Inc. All Rights Reserved

3 Table of Contents Table of Contents The Advantage MPD Two-Grade, Three-Grade and Single-Hose Dispensers Elevation Diagram Foundation Diagram The Advantage MPD Four-Grade and Single Hose + 1 Dispensers Elevation Diagram Foundation Diagram The Advantage MPD Two-Grade, Three-Grade and Four-Grade Pumps Elevation Diagram Two-Grade and Three-Grade Pumps Foundation Diagrams Four-Grade Pump Foundation Diagrams The Advantage Dual, Quad, and Super-Hi Dual Dispensers Elevation Diagram Foundation Diagram The Advantage Dual, Quad and Super-Hi Dual Pumps Elevation Diagram Foundation Diagram The Advantage Fixed Blender Six-Hose Dispenser Elevation Diagrams Foundation Diagram The Advantage Selectable Blender 36" Dispenser Elevation Diagram Foundation Diagram The Advantage Selectable Blender 48" Dispenser Elevation Diagram Foundation Diagram The Advantage Selectable Blender Pump Elevation Diagram Foundation Diagram MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page i

4 Metric Conversion Table Metric Conversion Table Inches Millimeters Inches Centimeters 1/ centimeters 1/ centimeters 3/ centimeters 1/ centimeters 5/ centimeters 3/ centimeters 7/ centimeters 1/ centimeters 9/ centimeters 5/ centimeters 11/ centimeters 3/ centimeters 13/ centimeters 7/ centimeters 15/ / / / / / / / / / / / / / / / / " = 25.4mm 1mm =.03937" Page ii MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

5 PRESS The Advantage MPD Two-Grade, Three-Grade and Single-Hose Dispensers Elevation Diagram The Advantage MPD Two-Grade, Three-Grade and Single-Hose Dispensers Elevation Diagram (Models B02, B03, B04, B05, B84, and B85) 5-1/8" 53-13/16" 49-1/2" 9-1/2" 31-5/16" 21" 42" 23-1/2" 94" 95-3/16" 60-1/2" Two-Grade units do not have the middle nozzle put-down. 16" 22" 21-1/4" (Long Nozzle Cradle) 22-1/2" (Medium Nozzle Cradle) 24-1/2" (Short Nozzle Cradle) 48" 21-1/2" 32-3/8" Short Nozzle Cradles 36-1/8" Long Nozzle Cradles Note: Gilbarco VaporVac and some Balance Vapor Recovery units use short nozzle cradles. Single-Line CRIND InfoScreen and Monochrome CRIND Single-Hose units have nozzle boot located on right side. 53-1/2" 53-1/2" Screening Specifications Lower Doors Overall: 22.94" H x 49.74" W Front Surface: 19.94" H x 42.25" W Front Surface: 9.5" H x 53.81" W Side Surface: 9.5" H x 31.31" W TD Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 1

6 The Advantage MPD Two-Grade, Three-Grade and Single-Hose Dispensers Foundation Diagram The Advantage MPD Two-Grade, Three-Grade and Single-Hose Dispensers Foundation Diagram (Models B02, B03, B04, B05, B84, B85) 7 1" V/R ADAPTER 3 1/2 10 3/4 9 1/ /2 3 1/ / OPENING/STUB-UP FOR 1/2" CONDUIT (SPEAKER & CALL BUTTON) OPENING/STUB-UP FOR 1/2" CONDUIT (OVERHEAD SPEAKER ONLY) AUXILLARY JUNCTION BOX (FOR OVERHEAD SPEAKER & CALL BUTTON) INSTALLER'S 1/2" CONDUIT & UNILET BOX (OVERHEAD SPEAKER ONLY) 9 5/ / /16 INSTALLER'S 1/2" CONDUIT (OVERHEAD SPEAKER & CALL BUTTON) 2 7/ /16 NOTES: 1 - INLET UNION HEIGHT SUCH TO ACCOMODATE A CUSTOMER SUPPLIED DOUBLE-POPPIT SHEAR VALVE. 2 - DISREGARD CENTER PRODUCT FOR 2-GRADE WIDE FRAME UNITS (4) 13/16 X 1 7/16 SLOTS FOR ANCHOR BOLTS 16 1/2 9 1/4 2 3/8 (3) 1 1/2 SUPPLY UNIONS 2 3/4 2 1/2 14 1/2 OPENING/STUB-UP FOR 1" CONDUIT /16 1" STANDARD ELBOW 1 X 2 3/8 LG NIPPLE POWER JUNCTION BOX 1" CAPPED ELBOW (SUPPLIED) INSTALLER'S 1" CONDUIT 1 X 1 1/2 LG NIPPLE FIELD J-BOX VIEW FACING THE COVER OF J-BOXES R19109 TD Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii.. Page 2 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

7 The Advantage MPD Two-Grade, Three-Grade and Single-Hose Dispensers Foundation Diagram Optional Conduit Locations (Models B02, B03, B04, B05, B84, B85) Optional Conduit Locations (See Standard Conduit Location drawing for all standard conduit locations.) TOP VIEW conduit 1/2" opening Speaker conduit opening 1/2" (Alternate Location - See MDE-3415) 2-1/4" 3-1/16" 22-1/2" Main conduit 3/4" opening (Alternate Column Location) (using Kit K ) 1-17/32" 16-3/16" 22-1/2" Speaker Unilet Box (Alternate Location - See MDE-3415) A SIDE Aux.Junction Box VIEW Aux.Junction Box J-BOX SIDE VIEW OF COLUMN Main Conduit (3) 3/4" Capped Elbow (supplied) Speaker Conduit Speaker Unilet Box Call Button Conduit Auxillary Junction Box 3-1/16" 16-7/10" 9-5/16" 7" RIGHT VIEW (Alternate Column Location) Using K LEFT VIEW (Alternate Column Location) See MDE-3415 LEFT VIEW TD Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii.. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 3

8 PRESS The Advantage MPD Four-Grade and Single Hose + 1 Dispensers Elevation Diagram The Advantage MPD Four-Grade and Single Hose + 1 Dispensers Elevation Diagram (Models B06, B07, B86, and B87) 53-13/16" 49-1/12" 31-5/16" 21" 5-1/8" 9-1/2" 42" 23-1/2" Detail B 88-7/8" 94" 95-3/16" 60-1/2" 16" 22" 25-5/8" 48" 21-1/2" 32-3/8" Short Nozzle Cradles 36-1/8" Long Nozzle Cradles 24-1/2" 22-1/2" (Short 21-1/4" (Medium Nozzle Cradle) (Long Nozzle Cradle) Nozzle Cradle) Single-Hose + 1 (uses both nozzle boots) Single-Hose (uses right hand nozzle boot) Note: Gilbarco VaporVac and some Balance Vapor Recovery units use short nozzle cradles. Screening Specifications Single-Line CRIND InfoScreen and Monochrome CRIND Detail B Lower Doors Overall: 22.94" H x 49.74" W Front Surface: 19.94" H x 42.25" W Front Surface: 9.5" H x 53.81" W Side Surface: 9.5" H x 31.31" W 53-1/2" 53-1/2" TD Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 4 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

9 The Advantage MPD Four-Grade and Single Hose + 1 Dispensers Elevation Diagram The Advantage MPD Four-Grade and Single-Hose Dispensers Foundation Diagram (Models B06, B07, B86 and B87)) THIS INLET FOR 1-PROD UNIT 13 5/8 16 1/2 TOP VIEW 2 3/8 3 3/4 10 3/4 9 1/ /2 21 1/2 3 1/ / OPENING/STUB-UP FOR 1/2" CONDUIT (SPEAKER & CALL BUTTON) 6 1/8 OPENING/STUB-UP FOR 1/2" CONDUIT (OVERHEAD SPEAKER ONLY) 14 1/2 16 3/ AUXILLARY JUNCTION BOX (FOR OVERHEAD SPEAKER & CALL BUTTON) INSTALLER'S 1/2" CONDUIT & UNILET BOX (OVERHEAD SPEAKER ONLY) 9 5/16 FIELD J-BOX 5 11/ / /16 2 7/16 VIEW FACING THE COVER OF J-BOXES INSTALLER'S 1/2" CONDUIT (OVERHEAD SPEAKER & CALL BUTTON) LEFT SIDE VIEW OF COLUMS 3 POWER JUNCTION BOX 1" V/R ADAPTER (4) 13/16 X 1 7/16 SLOTS FOR ANCHOR BOLTS (4) 1 1/2 SUPPLY UNIONS OPENING/STUB-UP FOR 3/4 CONDUIT 3/4 UNION (SUPPLIED) 1" INSTALLER'S CONDUIT 8 9/16 R19326 TD RIGHT SIDE VIEW OF COLUMS Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 5

10 The Advantage MPD Four-Grade and Single Hose + 1 Dispensers Elevation Diagram Optional Conduit Locations (Models B06, B07, B86 and B87) Optional Conduit Locations (See Standard Conduit Location drawing for all standard conduit locations.) TOP VIEW conduit 1/2" opening Speaker conduit opening 1/2" (Alternate Location - See MDE-3415) 2-1/4" 3-1/16" 22-1/2" Main conduit 3/4" opening (Alternate Column Location) (using Kit K ) 1-17/32" 16-3/16" 22-1/2" A SIDE Speaker Unilet Box (Alternate Location - See MDE-3415) Aux.Junction Box VIEW Aux.Junction Box J-BOX SIDE VIEW OF COLUMN Main Conduit (3) 3/4" Capped Elbow (supplied) Speaker Conduit Speaker Unilet Box Call Button Conduit Auxillary Junction Box 3-1/16" 16-7/10" 9-5/16" 7" RIGHT VIEW (Alternate Column Location) Using K LEFT VIEW (Alternate Column Location) See MDE-3415 LEFT VIEW TD Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 6 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

11 PRESS The Advantage MPD Two-Grade, Three-Grade and Four-Grade Pumps Elevation Diagram The Advantage MPD Two-Grade, Three-Grade and Four-Grade Pumps Elevation Diagram (Models B12, B13, B14, B15 and B17) 53-13/16" 49-1/2" 31-5/16" 21" 5-1/8" 9-1/2" 95-3/16" 94" 62-1/2" 16" 22" 23-1/4" (Long Nozzle Cradle) 24-1/2" (Medium Nozzle Cradle) 26-1/2" (Short Nozzle Cradle) 48" (50'' for Four-Grade Pump) Note: Three-Grade Pump shown. All dimensions for all grades the same except as noted for Four-Grade Pump. 21-1/2" 32-3/8" Short Nozzle Cradles 36-1/8" Long Nozzle Cradles 33" Four-Grade Extended Lower Panel (Door) Single-Line CRINDª Note: Gilbarco VaporVac and some Balance Vapor Recovery units use short nozzle cradles. InfoScreenª and Monochrome CRIND 55-1/2" 55-1/2" Screening Specifications Lower Doors Overall: 22.94" H x 49.74" W Front Surface: 19.94" H x 42.25" W Front Surface: 9.5" H x 53.81" W Side Surface: 9.5" H x 31.31" W TD Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 7

12 The Advantage MPD Two-Grade and Three-Grade Pumps Foundation Diagrams The Advantage MPD Two-Grade and Three-Grade Pumps Foundation Diagrams (Models B12, B13, B14 and B15) Standard Conduit Locations (See Optional Conduit Location drawing for column conduit locations and call button option locations.) TOP VIEW Speaker conduit opening 1/2" 1" Vapor recovery adapter hole location. 48" 24" 41-3/4" 20-7/8" 33" 16-1/2" Slot dimensions for front & back anchor bolts. (4) 13/16" x 1-7/16" 10-3/4" 9-1/4" 7-7/8" 7-11/32" 6" 'A' 'B' 'C' 1-3/16" 21-1/2" 18-1/2" 15-3/4" 1-3/16" 5-5/8" 10-11/16" 15-25/32" 18-23/32" 17/32" 15-25/32" 18-13/16" Supply union (3) 1-1/2" Main conduit 1" opening VIEW Vapor Recovery Adaptor Speaker Unilet Box Main Junction Box with main conduit Supply union 13-11/16" J-BOX 1-1/16" 1-1/16" SIDE VIEW OF COLUMN Main Conduit 1" Capped Elbow (supplied) Speaker Conduit Speaker Unilet Box 11" 13-11/16" RIGHT VIEW LEFT VIEW PRODUCT INLET LOCATIONS THREE-GRADE, THREE-GRADE SINGLE-HOSE A INLET FROM TANK A B INLET FROM TANK B C INLET FROM TANK C FUNCTION 3-GRADE, 3-HOSE - B14, BG4 3-GRADE, 6-HOSE - B15, BG5 3-GRADE, 1-HOSE - BP4 3-GRADE, 2-HOSE - BP5 TWO-GRADE A INLET FROM TANK A B NOT USED C INLET FROM TANK C FUNCTION 2-GRADE, 2-HOSE - B02 2-GRADE, 4-HOSE - B03 S Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 8 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

13 The Advantage MPD Two-Grade and Three-Grade Pumps Foundation Diagrams Optional Conduit Locations Optional Conduit Locations (See Standard Conduit Location drawing for all standard conduit locations.) TOP VIEW 10-11/16" 7-1/4" conduit 1/2" opening VIEW 7-5/8" J-BOX SIDE VIEW OF COLUMN Call Button Conduit 7-5/8" 7-1/4" LEFT VIEW S Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 9

14 The Advantage MPD Four-Grade Pump Foundation Diagrams The Advantage MPD Four-Grade Pump Foundation Diagrams (Model B17) TOP VIEW /2" SPEAKER CONDUIT 16 1/2 14 3/8 13 1/8 10 3/4 9 1/4 8 7/ / / /16 5 1/2 21 1/2 18 1/2 (4) 1-1/2 SUPPLY UNIONS 6 3/16 OPENING FOR 1" CONDUIT (4) 13/16 X 1-7/16 SLOTS FOR ANCHOR BOLTS POWER JUNCTION BOX 1 1/ / /8 REF SIDE VIEW OF COLUMN INSTALLER'S 1/2" SPEAKER CONDUIT (FOR OVERHEAD SPEAKER) Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 10 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

15 PRESS The Advantage Dual, Quad, and Super-Hi Dual Dispensers Elevation Diagram The Advantage Dual, Quad, and Super-Hi Dual Dispensers Elevation Diagram (Models B20, B21, BD0, BD1, B42, and B43) 41-13/16" 37-1/4" 31-5/16" 21" 5-1/8" 9-1/2" 95-3/16" 94" 60-1/2" 16" 22" 21-1/4" (Long Nozzle Cradle) 22-1/2" (Medium Nozzle Cradle) 24-1/2" (Short Nozzle Cradle) 36" The Advantage Dual and Super-Hi flow units are less left Put-down and PPU module 21-1/2" 32-3/8" Short Nozzle Cradles 36-1/8" Long Nozzle Cradles Note: Gilbarco VaporVac and some Balance Vapor Recovery units use short nozzle cradles. Single-Line CRIND InfoScreen and Monochrome CRIND 53-1/2" 53-1/2" Screening Specifications Lower Doors Overall: 22.94" H x 37.74" W Front Surface: 19.94" H x 30.24" W Front Surface: 9.5" H x 41.81" W Side Surface: 9.5" H x 31.31" W Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 11

16 The Advantage Dual, Quad and Super-Hi Dual Dispensers Foundation Diagram The Advantage Dual, Quad and Super-Hi Dual Dispensers Foundation Diagram (Models B20, B21, BD0, BD1, B42 and B43) 7 AUXILLARY JUNCTION BOX (FOR OVERHEAD SPEAKER & CALL BUTTON) INSTALLER'S 1/2" CONDUIT (OVERHEAD SPEAKER & CALL BUTTON) 1" V/R ADAPTER 9 1/4 3 1/2 18 1/2 3 1/16 5 OPENING/STUB-UP FOR 1/2" CONDUIT (SPEAKER & CALL BUTTON) OPENING/STUB-UP FOR 1/2" CONDUIT (OVERHEAD SPEAKER ONLY) INSTALLER'S 1/2" CONDUIT & UNILET BOX (OVERHEAD SPEAKER ONLY) 9 5/ /16 2 7/ / /16 NOTES: 1 - INLET UNION HEIGHT IS SUCH TO ACCOMODATE A CUSTOMER SUPPLIED DOUBLE-POPPIT SHEAR VALVE (4) 13/16 X 1 7/16 SLOTS FOR ANCHOR BOLTS /2 (3) 1 1/2 SUPPLY UNIONS 10 3/ /2 2 3/4 8 1/2 3 1/4 OPENING/STUB-UP FOR 1" CONDUIT 10 3/ " STANDARD ELBOW POWER JUNCTION BOX 1 X 1 1/2 LG NIPPLE FIELD J-BOX VIEW FACING THE COVER OF J-BOXES R19348 TD X 2 3/8 LG NIPPLE 1" CAPPED ELBOW (SUPPLIED) INSTALLER'S 1" CONDUIT Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 12 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

17 The Advantage Dual, Quad and Super-Hi Dual Dispensers Foundation Diagram Optional Conduit Locations (Models B20, B21, BD0, BD1, B42 and B43) Optional Conduit Locations (See Standard Conduit Location drawing for all standard conduit locations.) TOP VIEW conduit 1/2" opening 3-1/16" 'A' 'B' LEFT VIEW 10-3/16" Aux.junction box VIEW J-BOX SIDE VIEW OF COLUMN Call Button Conduit 3-1/16" 7" LEFT VIEW Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 13

18 PRESS The Advantage Dual, Quad and Super-Hi Dual Pumps Elevation Diagram The Advantage Dual, Quad and Super-Hi Dual Pumps Elevation Diagram (Models B30, B31, BE0, BE1, B52, and B53) 41-13/16" 37-1/4" 31-5/16" 21" 5-1/8" 9-1/2" Details A and B 95-3/16" 94" 62-1/2" Dual and Super-Hi units have no left nozzle boot 16" 22" 23-1/4" (Long Nozzle Cradle) 24-1/2" (Medium Nozzle Cradle) 26-1/2" (Short Nozzle Cradle) 36" 21-1/2" 32-3/8" Short Nozzle Cradles 36-1/8" Long Nozzle Cradles Note: Gilbarco VaporVac and some Balance Vapor Recovery units use short nozzle cradles. Single-Line CRIND InfoScreen and Monochrome CRIND Advantage International Quad Note: Advantage International units use centralized PPUs (effective August 1998). 55-1/2" 55-1/2" Screening Specifications Lower Doors Overall: 22.94" H x 37.74" W Front Surface: 19.94" H x 30.24" W Front Surface: 9.5" H x 41.81" W Side Surface: 9.5" H x 31.31" W S Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 14 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

19 The Advantage Dual, Quad and Super-Hi Dual Pumps Foundation Diagram The Advantage Dual, Quad and Super-Hi Dual Pumps Foundation Diagram (Models B30, B31, B52 and B53) Standard Conduit Locations (See Optional Conduit Location drawing for column conduit locations and call button option locations.) TOP VIEW Speaker conduit opening 1/2" 1" Vapor recovery adapter hole location 36" 18" 29-3/4" 14-7/8" 21" 10-1/2" Slot dimensions for front & back anchor bolts. (4) 13/16" x 1-7/16" 10-3/4" 9-1/4" 7-7/8" 7-1/4" 6" 15-3/4" 21-1/2" 18-1/2" 'B' 1-3/16" 1-3/16" 'A' 5-5/8" 8-29/32" 12-23/32" 2-11/16" 8-29/32" 12-13/16" Supply union (1 or 2) 1-1/2" Main conduit 1" opening VIEW Vapor Recovery Adaptor Speaker Unilet Box Main Junction Box with main conduit 7-5/16" J-BOX SIDE VIEW OF COLUMN 1-1/16" 1-1/16" 'A' 'B' Main Conduit Speaker Conduit 1" Capped Elbow (supplied) Speaker Unilet Box 11" 7-5/16" RIGHT VIEW LEFT VIEW TOP VIEW OF MODEL CONFIGURATIONS DUAL PUMP G1 SIDE B SUPER-HI DUAL PUMP G2 SIDE B QUAD PUMP G1 SIDE B G2 'A' 'B' 'A' 'B' 'A' 'B' SIDE A G1 SIDE A G1 G1 SIDE A G2 PRODUCT INLET LOCATIONS DUAL PUMP SUPER-HI DUAL PUMP QUAD PUMP A B INLET FROM TANK A NOT USED FUNCTION A B INLET FROM TANK A INLET FROM TANK A FUNCTION A B INLET FROM TANK A INLET FROM TANK B FUNCTION B30 1-GRADE, 1-HOSE, 1-SIDE (Uses position 'A') B21 1-GRADE, 1-HOSE, 2-SIDE BE0 1-GRADE, 1-HOSE, 1-SIDE (Uses position 'B') BE1 1-GRADE, 1-HOSE, 2-SIDE B52 2-GRADE, 2-HOSE, 1-SIDE (Uses position 'A and B') B53 2-GRADE, 2-HOSE, 2-SIDE NOTE: NUMBER OF HOSES LISTED ARE PER GRADE, PER SIDE. S Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 15

20 The Advantage Dual, Quad and Super-Hi Dual Pumps Foundation Diagram Optional Conduit Locations (Models B30, B31, B52 and B53) Optional Conduit Locations (See Standard Conduit Location drawing for all standard conduit locations.) TOP VIEW Aux.junction box 2-11/16" 7-1/4" 'B' 'A' conduit 1/2" opening VIEW 7-5/16" J-BOX SIDE VIEW OF COLUMN Call Button Conduit 7-5/16" 7-1/4" LEFT VIEW S Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 16 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

21 PRESS The Advantage Fixed Blender Six-Hose Dispenser Elevation Diagrams The Advantage Fixed Blender Six-Hose Dispenser Elevation Diagrams (Models B64 and B65) 53-13/16" 49-1/12" 31-5/16" 21" 5-1/8" 9-1/2" 42" 23-1/2" Detail B 601/2" 88-7/8" 94" 95-3/16" 16" 22" 25-1/4" 25-5/8" 48" 21-1/2" 32-3/8" Short Nozzle Cradles 36-1/8" Long Nozzle Cradles Single-Line CRIND InfoScreen and Monochrome CRIND Detail B 24-1/2" 22-1/2" (Short 21-1/4" (Medium Nozzle Cradle) (Long Nozzle Cradle) Nozzle Cradle) Note: Gilbarco VaporVac and some Balance Vapor Recovery units use short nozzle cradles. 53-1/2" 53-1/2" Screening Specifications Lower Doors Overall: 22.94" H x 49.74" W Front Surface: 19.94" H x 42.25" W Front Surface: 9.5" H x 53.81" W Side Surface: 9.5" H x 31.31" W Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 17

22 The Advantage Fixed Blender Six-Hose Dispenser Foundation Diagram The Advantage Fixed Blender Six-Hose Dispenser Foundation Diagram (Models B64 and B65) /2 AUXILLARY JUNCTION BOX (FOR OVERHEAD SPEAKER & CALL BUTTON) INSTALLER'S 1/2" CONDUIT (OVERHEAD SPEAKER & CALL BUTTON) 10 3/4 1" V/R ADAPTER 9 1/ /2 3 1/ / OPENING/STUB-UP FOR 1/2" CONDUIT (SPEAKER & CALL BUTTON) OPENING/STUB-UP FOR 1/2" CONDUIT (OVERHEAD SPEAKER ONLY) INSTALLER'S 1/2" CONDUIT & UNILET BOX (OVERHEAD SPEAKER ONLY) 9 5/ /16 2 7/ / /16 NOTES: 1 - INLET UNION HEIGHT IS SUCH TO ACCOMODATE A CUSTOMER SUPPLIED DOUBLE-POPPIT SHEAR VALVE. 48 (4) 13/16 X 1 7/16 SLOTS FOR ANCHOR BOLTS /8 16 1/2 (2) 1 1/2 SUPPLY UNIONS 3 1/16 7 5/8 OPENING/STUB-UP FOR 3/4 CONDUIT 14 1/2 7 5/8 16 3/ / /4 UNION (SUPPLIED) 3/4 UNION (SUPPLIED) POWER JUNCTION BOX INSTALLER'S 1" CONDUIT FIELD J-BOX 8 9/16 N23327 (BLUE TAG) LOW PRODUCT VIEW FACING THE COVER OF J-BOXES N23328 (WHITE TAG) HIGH PRODUCT R19447 TD Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 18 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

23 The Advantage Fixed Blender Six-Hose Dispenser Foundation Diagram Optional Conduit Locations (Models B64 and B65) Optional Conduit Locations (See Standard Conduit Location drawing for all standard conduit locations.) TOP VIEW conduit 1/2" opening Speaker conduit opening 1/2" (Alternate Location - See MDE-3415) 2-1/4" 3-1/16" 22-1/2" Main conduit 3/4" opening (Alternate Column Location) (using Kit K ) 1-17/32" 16-3/16" 22-1/2" Speaker Unilet Box (Alternate Location - See MDE-3415) Aux.Junction Box VIEW Aux.Junction Box J-BOX SIDE VIEW OF COLUMN Main Conduit (3) 3/4" Capped Elbow (supplied) Speaker Conduit Speaker Unilet Box Call Button Conduit Auxillary Junction Box 3-1/16" 16-7/10" 9-5/16" 7" RIGHT VIEW LEFT VIEW LEFT VIEW (Alternate Column Location) Using K (Alternate Column Location) See MDE-3415 Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 19

24 PRESS The Advantage Selectable Blender 36" Dispenser Elevation Diagram The Advantage Selectable Blender 36" Dispenser Elevation Diagram (Models B78, B7A, B7E, B7G, B7K, and B7N) 41-13/16" 37-1/4" 31-5/16" 21" 5-1/8" 9-1/2" Detail B 95-3/16" 94" 62" 42-1/4" 27-1/4" 16" 22" 25-1/4" 36" 22" 32-3/8" Short Nozzle Cradles 36-1/8" Long Nozzle Cradles Single-Line CRIND InfoScreen and Monochrome CRIND Detail B 24-1/2" 22-1/2" (Short 24-1/4" (Medium Nozzle Cradle) (Long Nozzle Cradle) Nozzle Cradle) 53-1/2" 53-1/2" Note: Gilbarco VaporVac and some Balance Vapor Recovery units use short nozzle cradles. Screening Specifications Lower Doors Overall: 22.94" H x 37.74" W Front Surface: 19.94" H x 30.24" W Front Surface: 9.5" H x 41.81" W Side Surface: 9.5" H x 31.31" W Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 20 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

25 The Advantage Selectable Blender 36" Dispenser Foundation Diagram The Advantage Selectable Blender 36" Dispenser Foundation Diagram (Models B78, B7A, B7E, B7G, B7K, and B7N) AUXILLARY JUNCTION BOX (FOR OVERHEAD SPEAKER & CALL BUTTON) 7 INSTALLER'S 1/2" CONDUIT (OVERHEAD SPEAKER & CALL BUTTON) VAPOR SHEAR VALVE LOCATION WHEN USING MOUNTING BRACKET KIT K / /4 9 1/ /16 3 1/ /2 18 1/ OPENING/STUB-UP FOR 1/2" CONDUIT (SPEAKER & CALL BUTTON) OPENING/STUB-UP FOR 1/2" CONDUIT (OVERHEAD SPEAKER ONLY) INSTALLER'S 1/2" CONDUIT & UNILET BOX (OVERHEAD SPEAKER ONLY) 5 11/ /16 9 5/16 1 1/16 2 7/ / /16 NOTES: 1 - INLET UNION HEIGHT SUCH TO ACCOMODATE A CUSTOMER SUPPLIED DOUBLE-POPPIT SHEAR VALVE. 2 DIMENSION IS TO TOP OF VAPOR SHEAR VALVE (NOT SHOWN) " V/R ADAPTER (STANDARD LOCATION) /2 (4) 13/16 X 1 7/16 SLOTS FOR ANCHOR BOLTS 3 1/4 (2) 1 1/2 SUPPLY UNIONS 3 1/2 2 3/4 OPENING/STUB-UP FOR 1" CONDUIT 8 1/ /16 1" STANDARD ELBOW 1 X 2-3/8 LG. NIPPLE POWER JUNCTION BOX 1" CAPPED ELBOW (SUPPLIED) HIGH PRODUCT 1" INSTALLER'S CONDUIT 1 X 1 1/2 LG NIPPLE 2 3/8 9 1/ /16 LOW PRODUCT R19471 VIEW FACING THE COVER OF J-BOXES TD Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 21

26 The Advantage Selectable Blender 36" Dispenser Foundation Diagram Optional Conduit Locations (Models B78, B7A, B7E, B7G, B7K, and B7N) Optional Conduit Locations (See Standard Conduit Location drawing for all standard conduit locations.) TOP VIEW conduit 1/2" opening 3-1/16" 'A' 'B' LEFT VIEW 10-3/16" Aux.junction box VIEW J-BOX SIDE VIEW OF COLUMN Call Button Conduit 3-1/16" 7" LEFT VIEW Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 22 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

27 PRESS The Advantage Selectable Blender 48" Dispenser Elevation Diagram The Advantage Selectable Blender 48" Dispenser Elevation Diagram (B79, B7B, B7C, B7D, B7F, B7H, B7I, B7J, B7L, B7M, B7O and B7P) 53-13/16" 49-1/12" 31-5/16" 21" 5-1/8" 9-1/2" 42" 23-1/2" Detail B 60-1/2" 88-7/8" 94" 95-3/16" 42-1/4" 16" 22" 25-1/4" 25-5/8" 48" 21-1/2" 32-3/8" Short Nozzle Cradles 36-1/8" Long Nozzle Cradles Single-Line CRIND InfoScreen and Monochrome CRIND Detail B 53-1/2" 53-1/2" A side Screening Specifications Lower Doors Overall: 22.94" H x 49.74" W Front Surface: 19.94" H x 42.25" W Front Surface: 9.5" H x 53.81" W Side Surface: 9.5" H x 31.31" W 24-1/2" 22-1/2" (Short 21-1/4" (Medium Nozzle Cradle) (Long Nozzle Cradle) Nozzle Cradle) Note: Gilbarco VaporVac and some Balance Vapor Recovery units use short nozzle cradles. B side Configuration example: Model - x+ 0, symmetrical, hose left Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 23

28 The Advantage Selectable Blender 48" Dispenser Foundation Diagram The Advantage Selectable Blender 48" Dispenser Foundation Diagram (B79, B7B, B7C, B7D, B7F, B7H, B7I, B7J, B7L, B7M, B7O and B7P) 7 1" V/R ADAPTER 2 3/8 10 3/4 9 1/4 3 1/2 21 1/ / /2 OPENING/STUB-UP FOR 1/2" CONDUIT (SPEAKER & CALL BUTTON) 14 1/2 16 OPENING/STUB-UP FOR 1/2" CONDUIT (OVERHEAD SPEAKER ONLY) 16 3/16 24 AUXILLARY JUNCTION BOX (FOR OVERHEAD SPEAKER & CALL BUTTON) INSTALLER'S 1/2" CONDUIT & UNILET BOX (OVERHEAD SPEAKER ONLY) 9 5/ /16-1/16 VIEW INSTALLER'S 1/2" CONDUIT (OVERHEAD SPEAKER & CALL BUTTON) 2 7/ /16 FACING THE COVER OF J-BOXES NOTES: 1 - INLET UNION HEIGHT IS SUCH TO ACCOMODATE A CUSTOMER SUPPLIED DOUBLE-POPPIT SHEAR VALVE /2 (4) 13/16 X 1 7/16 SLOTS FOR ANCHOR BOLTS 2 1/2 (3) 1 1/2 SUPPLY UNIONS 8 2 3/ /4 OPENING/STUB-UP FOR 1" CONDUIT ' STANDARD ELBOW LOW PRODUCT HIGH PRODUCT THIS INLET FOR +1 (STRAIGHT PRODUCT) ON X+1 MODELS 1 X 1 1/2 LG NIPPLE FIELD J-BOX 1 X 2 3/8 LG. NIPPLE 1" CAPPED ELBOW (SUPPLIED) INSTALLER'S CONDUIT 9 1/4 R19463 TD Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 24 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

29 The Advantage Selectable Blender 48" Dispenser Foundation Diagram Optional Conduit Locations (B79, B7B, B7C, B7D, B7F, B7H, B7I, B7J, B7L, B7M, B7O and B7P) Optional Conduit Locations (See Standard Conduit Location drawing for all standard conduit locations.) TOP VIEW conduit 1/2" opening Speaker conduit opening 1/2" (Alternate Location - See MDE-3415) 22-1/2" 2-1/4" 3-1/16" 16-3/16" Speaker Unilet Box (Alternate Location - See MDE-3415) Aux.Junction Box VIEW Aux.Junction Box J-BOX SIDE VIEW OF COLUMN Speaker Conduit Speaker Unilet Box Call Button Conduit Auxillary Junction Box 3-1/16" 9-5/16" 7" LEFT VIEW LEFT VIEW (Alternate Column Location) See MDE-3415 Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 25

30 PRESS The Advantage Selectable Blender Pump Elevation Diagram The Advantage Selectable Blender Pump Elevation Diagram (Models BAE, BA8, BAN, BAK, BAG, and BAA) 41-13/16" 37-1/4" 31-5/16" 21" 5-1/8" 9-1/2" Detail B 95-3/16" 94" 64" 46-1/4" 29-1/4" 16" 22" 25-1/4" 36" 22" 32-3/8" Short Nozzle Cradles 36-1/8" Long Nozzle Cradles Single-Line CRIND InfoScreen and Monochrome CRIND Detail B 28-1/2" 26-1/2" (Short 25-1/4" (Medium Nozzle Cradle) (Long Nozzle Cradle) Nozzle Cradle) 55-1/2" 55-1/2" Note: Gilbarco VaporVac and some Balance Vapor Recovery units use short nozzle cradles. Screening Specifications Lower Doors Overall: 22.94" H x 37.74" W Front Surface: 19.94" H x 30.24" W Front Surface: 9.5" H x 41.81" W Side Surface: 9.5" H x 31.31" W S Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 26 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

31 The Advantage Selectable Blender Pump Foundation Diagram The Advantage Selectable Blender Pump Foundation Diagram (Models BAE, BA8, BAN, BAK, BAG, and BAA) Standard Conduit Locations (See Optional Conduit Location drawing for column conduit locations and call button option locations.) TOP VIEW Speaker conduit opening 1/2" 1" Vapor recovery adapter hole location 36" 18" 29-3/4" 14-7/8" 21" 10-1/2" Slot dimensions for front & back anchor bolts. (4) 13/16" x 1-7/16" 10-3/4" 9-1/4" 7-7/8" 7-1/4" 6" 15-3/4" 21-1/2" 18-1/2" 'B' 1-3/16" 1-3/16" 'A' 5-5/8" Position A = low product Position B = high product 8-29/32" 12-23/32" 2-11/16" 8-29/32" 12-13/16" Supply union (1 or 2) 1-1/2" Main conduit 1" opening VIEW Vapor Recovery Adaptor Speaker Unilet Box Main Junction Box with main conduit 7-5/16" J-BOX SIDE VIEW OF COLUMN 1-1/16" 1-1/16" 'A' 'B' Main Conduit Speaker Conduit 1" Capped Elbow (supplied) Speaker Unilet Box 11" 7-5/16" RIGHT VIEW LEFT VIEW TOP VIEW OF MODEL CONFIGURATIONS DUAL PUMP G1 SIDE B SUPER-HI DUAL PUMP G2 SIDE B QUAD PUMP G1 SIDE B G2 'A' 'B' 'A' 'B' 'A' 'B' SIDE A G1 SIDE A G1 G1 SIDE A G2 PRODUCT INLET LOCATIONS DUAL PUMP SUPER-HI DUAL PUMP QUAD PUMP A B INLET FROM TANK A NOT USED FUNCTION A B INLET FROM TANK A INLET FROM TANK A FUNCTION A B INLET FROM TANK A INLET FROM TANK B FUNCTION B30 1-GRADE, 1-HOSE, 1-SIDE (Uses position 'A') B21 1-GRADE, 1-HOSE, 2-SIDE BE0 1-GRADE, 1-HOSE, 1-SIDE (Uses position 'B') BE1 1-GRADE, 1-HOSE, 2-SIDE B52 2-GRADE, 2-HOSE, 1-SIDE (Uses position 'A and B') B53 2-GRADE, 2-HOSE, 2-SIDE NOTE: NUMBER OF HOSES LISTED ARE PER GRADE, PER SIDE. S Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004 Page 27

32 The Advantage Selectable Blender Pump Foundation Diagram Optional Conduit Locations (Models BAE, BA8, BAN, BAK, BAG, and BAA) Optional Conduit Locations (See Standard Conduit Location drawing for all standard conduit locations.) TOP VIEW Aux.junction box 2-11/16" 7-1/4" 'A' 'B' conduit 1/2" opening VIEW 7-5/16" J-BOX SIDE VIEW OF COLUMN Call Button Conduit 7-5/16" 7-1/4" LEFT VIEW S Note: Measurements are in inches unless otherwise specified. See Metric Conversion Table on page ii. Page 28 MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004

33

34 2004 Gilbarco Inc West Friendly Avenue Post Office Box Greensboro, North Carolina Phone (336) Printed in the U.S.A. MDE-3807A The Advantage Series Pump and Dispenser Specifications January 2004