2005 Honda Civic DX ENGINE PERFORMANCE EVAP System - Civic (Except Hatchback & Hybrid)
|
|
- Norah Gordon
- 6 years ago
- Views:
Transcription
1 DTC P1456: EVAP CONTROL SYSTEM LEAKAGE (FUEL TANK SYSTEM) NOTE: The fuel system is designed to allow specified maximum vacuum and pressure conditions. Do not deviate from the vacuum and pressure tests as indicated in these procedures. Excessive pressure/vacuum would damage the EVAP components or cause eventual fuel tank failure. Special Tools Required Vacuum Pump/Gauge, 0-30 in. Hg A973X-041-XXXXX This is a two-trip code. Once cleared, it cannot be reproduced in one trip. Also, certain specific driving and ambient conditions must occur before the ECM/PCM will complete the system checks. Additional test drives may still not meet the specific conditions needed to reproduce the code. Follow these troubleshooting procedures carefully to ensure the integrity of the system and to confirm the cause of the problem or code. NOTE: Fresh fuel has a higher volatility that will create greater pressure/vacuum. The optimum condition for testing is fresh fuel, and must be less than a full tank of gas. If possible, to assist in leak detection, add 1 gallon of fresh fuel to the tank (as long as it will not fill the tank), just before starting these procedures. Fuel Fill Cap Check 1. Check the fuel fill cap (the cap must say "If not tightened 3 clicks check engine light may come on"). Is the proper fuel fill cap installed and properly tightened? YES - Go to step 2. NO - Replace or tighten the cap. 2. Check the fuel fill cap seal. Is the fuel fill cap seal missing or damaged? YES - Replace the fuel fill cap (gray or black colored cap). NO - The fuel fill cap is OK. Go to step 3. EVAP Canister Purge Valve Test 3. Disconnect the vacuum hose from the EVAP canister purge valve (A), and connect a vacuum pump to the hose. Friday, November 07, :53:28 12:53:33 PM Page Mitchell Repair Information Company, LLC.
2 Fig. 28: Disconnecting Vacuum Hose From EVAP Canister Purge Valve 4. Turn the ignition switch ON (II). 5. Apply vacuum to the hose. Does the valve hold vacuum? YES - The EVAP canister purge valve is OK. Go to step 11. NO - Go to step 6. Friday, November 07, :53:28 PM Page Mitchell Repair Information Company, LLC.
3 6. Turn the ignition switch OFF. 7. Disconnect the EVAP canister purge valve 2P connector. 8. Check for continuity between EVAP canister purge valve 2P connector terminal No. 2 and body ground. Fig. 29: Checking Continuity Between EVAP Canister Purge Valve 2P Connector Terminal No. 2 & Body Ground Is there continuity? YES - Go to step 9. NO - Replace the EVAP canister purge valve. 9. Disconnect ECM/PCM connector B (24P). Friday, November 07, :53:28 PM Page Mitchell Repair Information Company, LLC.
4 10. Check for continuity between EVAP canister purge valve 2P connector terminal No. 2 and body ground. Fig. 30: Checking Continuity Between EVAP Canister Purge Valve 2P Connector Terminal No. 2 & Body Ground Is there continuity? YES - Repair short in the wire between the EVAP canister purge valve and the ECM/PCM (B21). NO - Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck (see ECM/PCM UPDATING, SUBSTITUTION AND REPLACEMENT ). If the symptom/indication goes away with a known-good ECM/PCM, replace the original ECM/PCM. EVAP Bypass Solenoid Valve Test 11. Disconnect both vacuum hoses from the EVAP two way valve (A), and connect a vacuum pump to the Friday, November 07, :53:28 PM Page Mitchell Repair Information Company, LLC.
5 canister port on the EVAP two way valve. Fig. 31: Disconnecting Both Vacuum Hoses From EVAP Two-Way Valve 12. Turn the EVAP bypass solenoid valve ON with the HDS, or connect ECM/PCM connected terminal E20 to body ground with a jumper wire. Friday, November 07, :53:28 PM Page Mitchell Repair Information Company, LLC.
6 Fig. 32: Turning EVAP Bypass Solenoid Valve ON With HDS Or Connect ECM/PCM Connector Terminal E20 To Body Ground With Jumper Wire (ECM/PCM CONNECTOR E (31P)) 13. Turn the ignition switch ON (II). 14. Apply vacuum to the hose. Does the valve hold vacuum? YES - Go to step 15. NO - Go to step Turn the ignition switch OFF. 16. Disconnect the EVAP bypass solenoid valve 2P connector. 17. Check for continuity between EVAP bypass solenoid valve 2P connector terminal No. 2 and body ground. Friday, November 07, :53:29 PM Page Mitchell Repair Information Company, LLC.
7 Fig. 33: Checking Continuity Between EVAP Bypass Solenoid Valve 2P Connector Terminal No. 2 & Body Ground (EVAP CANISTER PURGE VALVE 2P CONNECTOR) Is there continuity? YES - Go to step 18. NO - Repair open in the wire between the EVAP bypass solenoid valve and the ECM/PCM (E20). 18. Turn the ignition switch ON (II). 19. Measure voltage between EVAP bypass solenoid valve 2P connector terminal No. 1 and body ground. Friday, November 07, :53:29 PM Page Mitchell Repair Information Company, LLC.
8 Fig. 34: Measuring Voltage Between EVAP Bypass Solenoid Valve 2P Connector Terminal No. 1 & Body Ground (EVAP CANISTER PURGE VALVE 2P CONNECTOR) Friday, November 07, :53:29 PM Page Mitchell Repair Information Company, LLC.
9 Fig. 35: Replacing EVAP Two-Way/Bypass Solenoid Valve Is there battery voltage? YES - Replace the EVAP two way/bypass solenoid valve (A). NO - Repair open in the wire between the EVAP bypass solenoid valve and the No. 4 ACG (10A) fuse. 20. Plug the fuel tank port (A) of the EVAP two way valve. Friday, November 07, :53:29 PM Page Mitchell Repair Information Company, LLC.
10 Fig. 36: Plugging Fuel Tank Port Of EVAP Two-Way Valve 21. While monitoring FTP sensor voltage with the HDS, or measuring the voltage between ECM/PCM connector terminals E4 and E14, slowly pump the vacuum pump until the voltage drops to about 1.5 volts. Friday, November 07, :53:29 PM Page Mitchell Repair Information Company, LLC.
11 Fig. 37: Measuring Voltage ECM/PCM Connector Terminals E4 & E14 (ECM/PCM CONNECTOR E (31P)) Does the voltage drop to 1.5 V and hold for at least 20 seconds? YES - The EVAP bypass solenoid valve/evap two way valve is OK. Go to step 22. NO - Repair the leak from the EVAP bypass solenoid valve, EVAP two way valve, and FTP sensor. EVAP Canister Vent Shut Valve Test 22. Disconnect the vacuum hose from the EVAP canister vent filter (A), and connect a vacuum pump to the hose. Friday, November 07, :53:29 PM Page Mitchell Repair Information Company, LLC.
12 Fig. 38: Disconnecting Vacuum Hose From EVAP Canister Vent Filter 23. Turn the ignition switch ON (II). 24. Apply vacuum to the hose with five strokes of the pump. Does the valve hold vacuum? YES - Go to step 25. NO - The EVAP canister vent shut valve is OK. Go to step Turn the ignition switch OFF. 26. Disconnect the EVAP canister vent shut valve 2P connector. 27. Check for continuity between EVAP canister vent shut valve 2P connector terminal No. 2 and body ground. Friday, November 07, :53:29 PM Page Mitchell Repair Information Company, LLC.
13 Fig. 39: Checking Continuity Between EVAP Canister Vent Shut Valve 2P Connector Terminal No. 2 & Body Ground Friday, November 07, :53:29 PM Page Mitchell Repair Information Company, LLC.
14 Fig. 40: Replacing EVAP Canister Vent Shut Valve & O-Ring Is there continuity? YES - Go to step 28. NO - Replace the EVAP canister vent shut valve (A) and O-ring (B). 28. Disconnect ECM/PCM connector E (31P). 29. Check for continuity between EVAP canister vent solenoid valve 2P connector terminal No. 2 and body ground. Friday, November 07, :53:29 PM Page Mitchell Repair Information Company, LLC.
15 Fig. 41: Checking Continuity Between EVAP Canister Vent Solenoid Valve 2P Connector Terminals No. 2 & Body Ground Is there continuity? YES - Repair short in the wire between the EVAP canister vent shut valve and the ECM/PCM (E21). NO - Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck (see ECM/PCM UPDATING, SUBSTITUTION AND REPLACEMENT ). If the symptom/indication goes away with a known-good ECM/PCM, replace the original ECM/PCM. Vacuum Hoses and Connections Test 30. Do the fuel tank vapor control valve test (see Fuel Tank Vapor Control Valve Test ). Friday, November 07, :53:29 PM Page Mitchell Repair Information Company, LLC.
16 Is the fuel tank vapor control valve OK? YES - Go to step 31. NO - Replace the fuel tank vapor control valve. 31. Tighten the fuel cap 3 "clicks", then monitor the FTP readings with the HDS or a scan tool. 32. Start the engine, and let it idle for 5 minutes. 33. Check the FTP sensor readings. Fig. 42: Checking FTP Sensor Readings Is the reading above 0.5 kpa (4 mm Hg, 0.16 in.hg) pressure, about 3 V? YES - Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck (see ECM/PCM UPDATING, SUBSTITUTION AND REPLACEMENT ). If the symptom/indication goes away with a known-good ECM/PCM, replace the original ECM/PCM. Friday, November 07, :53:29 PM Page Mitchell Repair Information Company, LLC.
17 NO - Check these parts for leaks: Fuel tank (A) Fuel fill cap (B) Fuel fill pipe (C) Fuel tank vapor control valve (D) Fuel tank vapor recirculation valve (E) Fuel tank vapor recirculation tube (F) Fuel tank vapor signal tube (G) Fuel tank vapor control vent tube (H) FTP sensor (J) Repair or replace any leaking parts. Friday, November 07, :53:29 PM Page Mitchell Repair Information Company, LLC.
2005 Honda Civic DX. Information marked with an asterisk (*) applies to the D17A2 engine.
DTC P0135: PRIMARY HO2S (SENSOR 1) HEATER CIRCUIT MALFUNCTION NOTE: Information marked with an asterisk (*) applies to the D17A2 engine. 1. Reset the ECM/PCM (see HOW TO RESET THE ECM/PCM ). 2. Start the
More information2004 Honda Element EX DTC P2647: ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) CIRCUIT HIGH VOLTAGE
DTC P2647: ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) CIRCUIT HIGH VOLTAGE NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting
More informationCOMPONENT LOCATION INDEX
DTC TROUBLESHOOTING COMPONENT LOCATION INDEX 2007-08 ENGINE PERFORMANCE Idle Control System - Element Fig. 1: Identifying Idle Control System Component Location DTC P0506: IDLE CONTROL SYSTEM RPM LOWER
More information2001 Honda Accord DX DTC P0135: PRIMARY HO2S (SENSOR 1) HEATER CIRCUIT MALFUNCTION, DTC P0141: SECONDARY HO2S (SENSOR 2) HEATER CIRCUIT MALFUNCTION
DTC P0135: PRIMARY HO2S (SENSOR 1) HEATER CIRCUIT MALFUNCTION, DTC P0141: SECONDARY HO2S (SENSOR 2) HEATER CIRCUIT MALFUNCTION NOTE: Information marked with an asterisk (*) applies to DTC P0141. 1. Reset
More informationPGM-FI MAIN RELAY CIRCUIT TROUBLESHOOTING
PGM-FI MAIN RELAY CIRCUIT TROUBLESHOOTING 1. Turn the ignition switch OFF, then disconnect the PGM-FI main relay 7P connector. 2. Check for continuity between body ground and PGM-FI main relay 7P connector
More informationDTC P1259: VTEC System Malfunction. Special Tools Required
DTC P1259: VTEC System Malfunction Special Tools Required Pressure gauge adapter 07NAJ-P07010A A/T low pressure gauge w/panel 07406-0070300 A/T pressure hose 07406-0020201 A/T pressure hose, 2,210 mm 07MAJ-PY4011A
More informationEmission Control System
Emission Control System Exhaust Gas Recirculation (EGR) System [B18A1 engine: A/T] Troubleshooting Flowchart The Malfunction Indicator Lamp (MIL) indicates Diagnostic Trouble Code (DTC) 12: A problem in
More informationEmission Control System
Emission Control System Exhaust Gas Recirculation System Troubleshooting Flowchart Self diagnosis indicates code 12: Most likely a problem in the Exhaust Gas Recirculation (EGR) system. The EGR System
More informationEvaporative Emission Control System Operation Description (Enhanced)
Page 1 of 7 1999 Chevrolet Chevy Suburban - 2WD Escalade, Pickup (Classic), Suburban, Tahoe, Yukon (VIN C/K) Service Manual Document ID: 222842 Evaporative Emission Control System Operation Description
More informationP0441-EVAP PURGE SYSTEM PERFO... P0441-EVAP PURGE SYSTEM PERFORMANCE
P0441-EVAP PURGE SYSTEM PERFO... P0441-EVAP PURGE SYSTEM PERFORMANCE For a complete wiring diagram, refer to the Wiring Information. Theory of Operation EVAP SYSTEM COMPONENTS CALLOUT DESCRIPTION 1 Filter
More information1998 Acura 3.5RL. F - BASIC TESTING' '1998 ENGINE PERFORMANCE Acura - Basic Diagnostic Procedures
FUEL PUMP 1. Remove fuel tank filler cap. Listen for fuel pump operation noise at fuel tank filler. Fuel pump should operate for 2 seconds after ignition switch is turned on. If fuel pump operates as specified,
More informationEvaporative Emission Control System Operation Description
Page 1 of 5 2000 Chevrolet Venture Ext. Montana, Silhoutte, Trans Sport, Venture (VIN U) Service Manual Engine Engine Controls - 3.4L Description and Operation Evaporative Emission Control System Operation
More information2002 Buick Rendezvous - AWD
2002 Buick Rendezvous - AWD DTC P0410 Description The control module activates the secondary air injection (AIR) system by grounding both the pump relay and the vacuum control solenoid control circuits.
More informationDTC P0455 EVAP CONTROL SYSTEM
On Board Diagnosis Logic PFP:14950 This diagnosis detects a very large leak (fuel filler cap fell off etc.) in EVAP system between the fuel tank and EVAP canister purge volume control solenoid valve. UBS00B8S
More information1 of 14 9/4/2016 4:05 PM
1 of 14 9/4/2016 4:05 PM P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION P0068-Manifold Pressure/Throttle Position Correlation Theory of Operation This DTC sets when an unexpected high intake manifold
More informationOn Board Diagnostics II A PCED
Page 1 of 8 HX18 DTC P0446 OR P1450: CHECK FOR VISUAL CAUSES OF EXCESSIVE FUEL TANK VACUUM Continuous Memory Diagnostic Trouble Code (DTC) P0446 or P1450 indicates that Self-Test has detected the Evaporative
More information2003 Chevrolet S10 - Engine Performance & Emission Controls > Engine Controls - 4.3L > Diagn...
Page 1 of 7 2003 Chevrolet S10 : Engine Performance & Emission Controls > Engine Controls -4.3L > Diagnostic Information And Procedures > DTC P0442 DTC P0442 DTC P0442 System Description This diagnostic
More informationIt is normal for the A/C compressor to turn off under certain conditions, such as low idle, high engine coolant temperature, or hard acceleration.
2007 Honda Odyssey 3.5L Eng LX 1Search AC COMPRESSOR CLUTCH A/C Compressor Clutch Circuit Troubleshooting NOTE: It is normal for the A/C compressor to turn off under certain conditions, such as low idle,
More informationControl Module Command EVAP Canister Purge Valve EVAP Canister Vent Valve ON Open Closed OFF Closed Open
DTC P0440 System Description The control module tests the evaporative emission (EVAP) system for a large leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP
More informationP0456-EVAP PURGE SYSTEM SMALL LEAK
2014 Journey (2.4L L4) - JC P0456-EVAP PURGE SYSTEM SMALL LEAK Report a problem with this article Special Tools: Click to display a list of tools used in this procedure For a complete wiring diagram, refer
More informationDTC P0451(A) EVAPORATIVE EMISSION CONTROL SYSTEM PRESSURE SENSOR/SWITCH RANGE/PERFORMANCE
05210 DTC (A) EVAPORATIVE EMISSION CONTROL RANGE/PERFORMANCE 052NT12 DTC P0452 EVAPORATIVE EMISSION CONTROL LOW INPUT DTC P0453 EVAPORATIVE EMISSION CONTROL HIGH INPUT CIRCUIT DESCRIPTION The vapor pressure
More informationDTC P0340 CMP SENSOR (PHASE) DTC No. Trouble diagnosis name DTC detecting condition Possible cause
DTC P0340 CMP SENSOR (PHASE) Component Description DTC P0340 CMP SENSOR (PHASE) The camshaft position sensor (PHASE) senses the retraction with intake valve camshaft to identify a particular cylinder.
More information1999 Dodge Caravan ENGINE PERFORMANCE Self-Diagnostics - Caravan, Town & Country, & Voyager
1. Attempt to start engine. If engine does not start, go to next step. If engine starts, go to step 4. 2. Turn ignition off. Disconnect connectors at Powertrain Control Module (PCM). PCM is located between
More informationDiagnostic Procedure
2001 Xterra Report a problem with this article If P0455 is displayed on the screen, go to Diagnostic Procedure, EC-402. If P0440 is displayed on the screen, go to Diagnostic Procedure, EC-356. If P1440
More information2001 CIVIC - Immobilizer System Troubleshooting
Page 1 of 5 2001 CIVIC - Immobilizer System Troubleshooting 1. Turn the ignition switch ON (II) with a programmed key. 2. Check to see if the immobilizer indicator comes on. Does the indicator come on?
More informationCOMPONENT LOCATION INDEX
COMPONENT LOCATION INDEX 2003-04 ACCESSORIES & EQUIPMENT Gauges - Element Fig. 1: Identifying Gauges Component Locations Page 1 Fig. 2: Locating Gauges & Gauge Connectors & Identifying Gauge Connector
More informationOn Board Diagnostics II PCED
Page 1 of 5 1999 PCED On Board Diagnostics II SECTION 5: Pinpoint Tests HD: Misfire Detection Monitor HD: Introduction HD1 DTC P0301-P0310: CHECK FOR NO LOW FUEL te: Running out of fuel can turn on the
More informationFuel injection system, servicing
24-1 Fuel injection system, servicing Component locations overview 1 - Oxygen sensor 1 before Three Way Catalyst G39 2 - Oxygen sensor 2 after Three Way Catalyst G130 3 - Engine Coolant Temperature sensor
More informationSymptom: P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELA- TION - VACUUM LEAK DETECTED
Symptom: P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELA- TION - VACUUM LEAK DETECTED When Monitored and Set Condition: VAC- UUM LEAK DETECTED When Monitored: During all drive modes. Set Condition: If
More informationP144F REQUESTED INFORMATION P144F EGR COOLER BYPASS STATUS LINE CIRCUIT HIGH RAM Pickup 6.7L Eng /12/2014 Printer Friendly View
P144F 2012 RAM Pickup 6.7L Eng 2500 REQUESTED INFORMATION P144F EGR COOLER BYPASS STATUS LINE CIRCUIT HIGH http://www1.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=true&ymms=false&classname=
More information4/24/2017 A L L Diagnostic Trouble Codes ( DTC ) Testing and Inspection, P Code Charts: P0441
Vehicle» A L L Diagnostic Trouble Codes ( DTC )» Testing and Inspection» P Code Charts» P0441 DTC P0441 Evaporative Emission Control System Incorrect Purge Flow CIRCUIT DESCRIPTION http://repair.alldata.com/alldata/article/display.action?componentid=3926&itypeid=423&nonstandardid=2379425&vehicleid=38048&windowname=mainadonlin
More informationPage 1 sur 5. Diagnostic Trouble Code Diagnosis Charts. Sportage [AL] > 2000 > Engine > 2.0 DOHC
Page 1 sur 5 Sportage [AL] > 2000 > Engine > 2.0 DOHC Diagnostic Trouble Code Diagnosis Charts P0440 / P0442 Threshold Values (P0440) ~ 1. At start of leak check ~ Fuel tank pressure:< -14.89 hpa in 20
More information1 CONFIRM DTC 2 PERFORM EVAP SYSTEM CHECK 3 CHECK OPERATION FOR PRESSURE SWITCHING VALVE INSPECTION PROCEDURE ES 240
240 1NZ-FXE EINE CONTROL SYSTEM SFI SYSTEM INSPECTION PROCEDURE 1 CONFIRM DTC Turn the power switch OFF and wait for 10 seconds. Turn the power switch ON (IG). (c) Turn the power switch OFF and wait for
More informationDTC P0442 Evaporative Emission Control System Leak Detected (small leak) DTC P0456 Evaporative Emission Control System Leak Detected (very small leak)
DI148 EINE DIAFV01 DTC P0442 Evaporative Emission Control System Leak Detected (small leak) DTC P0456 Evaporative Emission Control System Leak Detected (very small leak) CIRCUIT DESCRIPTI The vapor pressure
More informationP0456-EVAP PURGE SYSTEM SMALL LEAK
0 - JK - JEEP WRANGLER - 38L V6 (SMPI) P0456-EVAP PURGE SYSTEM SMALL LEAK MODULE- POWERTRAIN ESIM SIGNAL EVAP PURGE CONTROL EVAP PURGE RETURN CONTROL 35 C3 0 C3 9 C3 K07 8 VT/WT 5 C300 K07 8 VT/WT ESIM
More informationDO NOT adjust by-pass valve full-close screw. Adjustment is preset at factory.
I - SYSTEM/COMPONENT TESTS Article Text 1993 Honda Prelude For Cadi Centre Nsk CA 95051 Copyright 1998 Mitchell Repair Information Company, LLC Sunday, July 08, 2001 11:31AM ARTICLE BEGINNING 1993 ENGINE
More information1GR-FE ENGINE CONTROL SYSTEM SFI SYSTEM. DTC Monitoring Items Malfunction Detection Conditions Trouble Areas Detection Timings.
1GR-FE ENGINE CTROL SYSTEM SFI SYSTEM 239 DTC DTC DTC SUMMARY P0455 P0456 Evaporative Emission Control System Leak Detected (Gross Leak) Evaporative Emission Control System Leak Detected (Very Small Leak)
More informationDTC P0102 Mass Air Flow (MAF) Sensor Circuit Low Frequency
Seite 1 von 5 Document ID# 187823 1998 Chevrolet/Geo Tahoe - 2WD Print DTC P0102 Mass Air Flow (MAF) Sensor Circuit Low Frequency Circuit Description The mass air flow (MAF) sensor is
More information7. Evaporative Emission Control System
W1860BE.book Page 10 Tuesday, January 28, 2003 11:01 PM 7. Evaporative Emission Control System A: GENERAL The evaporative emission control system prevents fuel vapors from escaping into atmosphere. This
More informationOn Board Diagnostics II A PCED
Page 1 of 5 1998 PCED On Board Diagnostics II A SECTION 5A: Pinpoint Tests KE: Idle Air Control (IAC) Valve KE: Introduction KE1 IDLE CONCERNS OR STALLS: RUN KOER SELF-TEST AND OUTPUT CONTINUOUS MEMORY
More informationPage 1 of 8 HW7 DTC P1443: CHECK THE VOLTAGE ON THE PURGE FLOW (PF) SENSOR CIRCUIT VOLTAGE WITH ENGINE RUNNING Continuous Memory Diagnostic Trouble Code (DTC) P1443 indicates an incorrect evaporative system
More information1 of 7 12/18/2016 9:15 PM
1 of 7 12/18/2016 9:15 PM P0456-EVAP SYSTEM SMALL LEAK Special Tools: For a complete wiring diagram, refer to the Wiring Information. 2 of 7 12/18/2016 9:15 PM Theory of Operation 3 of 7 12/18/2016 9:15
More informationP245C REQUESTED INFORMATION P245C EGR COOLER BYPASS CONTROL CIRCUIT LOW RAM Pickup 6.7L Eng /12/2014 Printer Friendly View
P245C 2012 RAM Pickup 6.7L Eng 2500 REQUESTED INFORMATION P245C EGR COOLER BYPASS CONTROL CIRCUIT LOW http://www1.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=true&ymms=false&classname=
More information2002 Ford Crown Victoria LX MIL WITH DTC'S P0442, P0455, P0456, P0457, P1442 OR CHECK FUEL CAP LAMP WITH DTC P0457
MIL WITH DTC'S P0442, P0455, P0456, P0457, P1442 OR CHECK FUEL CAP LAMP WITH DTC P0457 TECHNICAL SERVICE BULLETIN Reference Number(s): 03-20-3, Date of Issue: October 13, 2003 1997-2000 CONTOUR; 1997-2002
More informationDTC P0440 EVAPORATIVE EMISSION CONTROL SYSTEM MALFUNCTION DTC P0442 EVAPORATIVE EMISSION CONTROL SYSTEM MALFUNCTION
0536 SFI SYSTEM (ZZGE) DTC P0440 EVAPORATIVE EMISSION CONTROL SYSTEM MALFUNCTION 057I003 DTC P044 EVAPORATIVE EMISSION CONTROL SYSTEM MALFUNCTION CIRCUIT DESCRIPTION The vapor pressure sensor, VSV for
More informationOxygen sensor control,
Page 1 of 46 24-71 Oxygen sensor control, checking Oxygen sensor and oxygen sensor control before catalytic converter, checking Special Tools and Equipment VAG1526A VAG1594A VAG1598/31 VAS5051 with VAG5051/1
More informationcylinder cars / trucks (except Saturn S-series cars) ENGINE DIAGNOSTIC PARAMETERS
2001 4-cylinder cars / trucks (except Saturn S-series cars) ENGINE DIAGNOSTIC S SECONDARY S AND Manifold Pressure/Throttle Position Sensor Manifold Pressure/Throttle Position Sensor Manifold Pressure Too
More informationDTC P0171, P0172, P0174, or P0175
Page 1 of 6 2009 Pontiac G8 G8 Service Manual Document ID: 2076050 DTC P0171, P0172, P0174, or P0175 Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic
More informationEVAP system, servicing
Page 1 of 65 20-130 EVAP system, servicing EVAP system components 1 - Cap nut 10 Nm 2 - Cover 3 - Stud For EVAP canister 15 Nm 4 - Sealing piece 5 - Bleed line To EVAP canister purge regulator valve -
More information1996 Toyota Camry DX ENGINE PERFORMANCE Toyota Basic Diagnostic Procedures
FUEL SYSTEM Basic diagnosis of fuel system should begin by checking fuel pump operation and fuel pressure. WARNING: ALWAYS release fuel pressure before disconnecting any fuel injection-related component.
More informationPowertrain DTC Summaries OBD II
Powertrain DTC Summaries Quick Reference Diagnostic Guide Jaguar X-TYPE 2.5L and 3.0L 2002 Model Year Revised January, 2002: P0706, P0731, P0732, P0733, P0734, P0735, P0740, P1780 POSSIBLE CAUSES Revised
More informationDTC P1655 Evaporative Emission (EVAP) Purge Solenoid Control Circuit
Page 1 of 5 1997 Pontiac Grand Am Achieva, Grand Am, Skylark (VIN N) Service Manual Document ID: 58460 DTC P55 Evaporative Emission (EVAP) Purge Solenoid Control Circuit Circuit Description Output Driver
More informationINSPECTION. 3. INSPECT FUEL TANK CAP Visually check if the cap and/or gasket are deformed or damaged. If necessary, repair or replace the cap.
EMISSION CONTROL EC5 EC0E601 INSPECTION 1. INSPECT LINES AND CONNECTORS Visually check for loose connections, sharp bends or damage. 2. INSPECT FUEL TANK FILLER PIPE Visually check for deformation, cracks
More informationFor Troubleshooting of DTC related components, see chart on page INTAKE AIR BYPASS (IAB) HIGH CONTROL SOLENOID
Index For Troubleshooting of DTC related components, see chart on page 11-53. '96-99 models: EXHAUST GAS RECIRCULATION (EGR) and LIFT MANIFOLD ABSOLUTE PRESSURE (MAP) INTAKE AIR BYPASS (IAB) HIGH page
More informationFig.11 Powertrain Control Module (PCM)
2003 Dodge or Ram Truck Caravan V6-3.3L VIN R Vehicle > Powertrain Management > Relays and Modules - Powertrain Management > Relays and Modules - Computers and Control Systems > Engine Control Module >
More informationMalfunction Criteria and Threshold Value Adaptive value. Secondary Parameters with Enable Conditions. >50.8 S Engine load 9-45% Delta fuel adaptation
DTC Error Message P0171 System Too Lean (Bank 1) Diagnostic Procedure Check fuel pump delivery and quantity. Refer to page 126. Check Fuel pressure regulator and residual pressure. Refer to Fuel Injection
More informationPowertrain DTC Summaries EOBD
Powertrain DTC Summaries Quick Reference Diagnostic Guide Jaguar S-TYPE V6, V8 N/A and V8 SC 2002.5 Model Year Refer to pages 2 9 for important information regarding the use of Powertrain DTC Summaries.
More information1 of 8 9/11/2015 3:59 PM
1 of 8 9/11/2015 3:59 PM P013C-O2 SENSOR 2/2 SLOW RESPONSE - RICH TO LEAN For complete wiring diagrams refer to Diagrams/Electrical. - When Monitored: With the engine running, vehicle speed between 32
More information2011 Cadillac SRX SRX VIN N Service Manual #PI0703B: Service Rear Axle Message Displayed on Driver Information Center (DIC), DTC C0407 with Symptom Code 64 or C0403 Symptom Code 62 Set - (Feb 25, 2013)
More informationDIAGNOSTIC TROUBLE CODE CHART
DIAGNOSTIC TROUBLE CODE CHART 05 35 HINT: As for the vehicle for MEXICO, refer to Repair Manual 2003 COROLLA MATRIX (Pub. No. RM940U). Parameters listed in the chart may not be exactly the same as your
More informationDIAGNOSTIC TROUBLE CODE CHART HINT:
DIAGNOSTICS DIAGNOSTIC TROUBLE CODE CHART HINT: SFI SYSTEM (1MZFE) 05241 Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument or other factors. If a
More informationUse only gold-plated terminals when servicing terminals in harness connector. The respective fuses of Diesel-Direct fuel injection system must be OK:
Page 1 of 7 Volkswagen > A4 Platform > 1999-2005 1.9 Liter 4-Cyl. 2V TDI and TDI PD Generic Scan Tool, Engine Code(s): ALH, BEW 26 - Exhaust system, Emission controls Exhaust Gas Recirculation (EGR) system
More informationDTC P0441 EVAPORATIVE EMISSION CONTROL SYSTEM INCORRECT PURGE FLOW DTC P0446 EVAPORATIVE EMISSION CONTROL SYSTEM VENT CONTROL MALFUNCTION
05180 DIAGNOSTICS DTC P0441 EVAPORATIVE EMISSION CONTROL SYSTEM INCORRECT PURGE FLOW 05DJV01 DTC P0446 EVAPORATIVE EMISSION CONTROL SYSTEM VENT CONTROL MALFUNCTION CIRCUIT DESCRIPTION The vapor pressure
More informationFOR HELP WITH USING witech FOR ECU FLASH REPROGRAMMING, CLICK ON THE APPLICATION S HELP TAB.
NUMBER: GROUP: 18-022-17 REV. B Vehicle Performance DATE: April 07, 2017 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may
More informationA/T INTERLOCK SYSTEM Acura TSX AUTOMATIC TRANSMISSIONS A/T Interlock System - TSX COMPONENT LOCATION INDEX
A/T INTERLOCK SYSTEM COMPONENT LOCATION INDEX 2004 AUTOMATIC TRANSMISSIONS A/T Interlock System - TSX Fig. 1: Locating A/T Interlock System Components CIRCUIT DIAGRAM Wednesday, March 12, 2008 9:52:31
More informationPowertrain DTC Summaries EOBD
Powertrain DTC Summaries Quick Reference Diagnostic Guide Jaguar X-TYPE 2.0 L 2002.25 Model Year Refer to page 2 for important information regarding the use of Powertrain DTC Summaries. Jaguar X-TYPE 2.0
More informationDTC P0451 EVAPORATIVE EMISSION CONTROL SYSTEM PRESSURE SENSOR/SWITCH RANGE/PERFORMANCE
DTC P0451 EVAPORATIVE EMISSION CONTROL SYSTEM PRESSURE SENSOR/SWITCH RANGE/PERFORMANCE 05255 052NT23 DTC P0452 EVAPORATIVE EMISSION CONTROL SYSTEM PRESSURE SENSOR/SWITCH LOW INPUT DTC P0453 EVAPORATIVE
More informationDocument ID: Some customers may comment that the service rear axle message is displayed on the driver information center (DIC).
Page 1 of 14 Document ID: 2789612 #PI0703: Service Rear Message Displayed on Driver Information Center (DIC), DTC C0407 with Symptom Code 64 or C0403 with Symptom Code 62 Set - (Mar 20, 2012) Subject:
More informationDTC P0441 EVAPORATIVE EMISSION CONTROL SYSTEM INCORRECT PURGE FLOW DTC P0446 EVAPORATIVE EMISSION CONTROL SYSTEM VENT CONTROL CIRCUIT
05202 DTC P0441 EVAPORATIVE EMISSION CONTROL SYSTEM INCORRECT PURGE FLOW 05FNT02 DTC P0446 EVAPORATIVE EMISSION CONTROL SYSTEM VENT CONTROL CIRCUIT CIRCUIT DESCRIPTION The vapor pressure sensor and VSV
More informationVAPOR TRAILS: FINDING & FIXING EVAPORATIVE SYSTEM FAULTS. by 1975 and established the U.S. Environmental
VAPOR TRAILS: FINDING & FIXING EVAPORATIVE SYSTEM FAULTS BY BOB PATTENGALE Current OBD II systems can detect evap system leaks too small to see, or even smell. Finding and fixing these and other system
More information2011 Transit Connect Workshop Manual
SECTION 303-12: Intake Air Distribution and Filtering REMOVAL AND INSTALLATION Procedure revision date: 09/23/2010 Intake Air System Components - Exploded View Item Part Number 1 9F991 Throttle Body (TB)
More informationP0088-FUEL RAIL PRESSURE TOO HIGH
2008 - KA - DODGE NITRO - 2.8L 4 CYL TURBO DIESEL 28 - DTC-Based Diagnostics/MODULE, Engine Control (ECM)/Diagnosis and Testing P0088- RAIL TOO HIGH BATT A0 30 RELAY- AUTO SHUT DOWN MODULE- TOTALLY INTEGRATED
More informationEmissions Theory and Diagnostics
SECTION 1 Introduction 5-Gas Theory Emissions History OBD II SECTION 2 PCV System Function Failure Diagnosis Emissions Theory and Diagnostics SECTION 3 EGR EGR Theory Vacuum Systems Backpressure Systems
More informationSECONDARY PARAMETERS AND ENABLE CONDITIONS
SECONDARY S AND Manifold Pressure Sensor Rationality Manifold Pressure Too Low Manifold Pressure Too High Intake Air Temperature Sensor Shorted Intake Air Temperature Sensor Open Coolant Temperature Sensor
More informationIntake Manifold Tuning (IMT)
Page 1 of 11 24-154 Intake Manifold Tuning (IMT) system Notes: The change-over of the manifold from long to short intake path occurs at approx. 4500 RPM. Component location page 24-1 Required special tools
More informationDIAGNOSTIC TROUBLE CODE CHART
DIAGNOSTIC TROUBLE CODE CHART HINT: DI231 Parameters listed in the chart may not be exactly the same as your readings due to the type of instrument or other factors. If a malfunction code is displayed
More informationCOMPONENT LOCATION INDEX
COMPONENT LOCATION INDEX 2011-12 ENGINE Ignition System - Odyssey Fig. 1: Identifying Ignition System Replacement Components IGNITION TIMING INSPECTION 1. Connect the HDS to the DLC (see step 2 on HOW
More informationTurbocharger system. Note: Observe rules of cleanliness Page Charge air pressure control connection diagram Page 21-2.
Page 1 of 50 21-1 Turbocharger system Note: Observe rules of cleanliness Page 21-22. Charge air pressure control connection diagram Page 21-2. All hose connections are secured with hose clamps: parts catalog.
More informationFuel Pump Electrical Circuit Diagnosis
1999 Chevrolet/Geo Tahoe - 4WD Fuel Pump Electrical Circuit Diagnosis Refer to Fuel Controls. Circuit Description When the ignition switch is turned ON, the VCM energizes the fuel pump relay which powers
More information#PIP4862A: Service Rear Axle Message Displayed DTC C0407 Sym64 - (Sep 21, 2011)
Page 1 of 5 Document ID: 2714825 #PIP4862A: Service Rear Axle Message Displayed DTC C0407 Sym64 - (Sep 21, 2011) Subject: Service Rear Axle Message Displayed DTC C0407 Sym64 Models: 2010-2012 Buick Lacrosse
More informationGROUP 13C 13C-1 CONTENTS GENERAL DESCRIPTION... 13C-2 FUEL TANK... 13C-11 FUEL SUPPLY DIAGNOSIS... 13C-3 SPECIAL TOOLS... 13C-8
13C-1 GROUP 13C CONTENTS GENERAL DESCRIPTION......... 13C-2 DIAGNOSIS....... 13C-3 INTRODUCTION TO DIAGNOSIS........................ 13C-3 TROUBOLESHOOTING STRATEGY..... 13C-3 SYMPTOM CHART...................
More information2.8 Liter VR6 2V Fuel Injection & Ignition, Engine Code(s): AAA m.y
2.8 Liter VR6 2V Fuel Injection & Ignition, Engine Code(s): AAA m.y. 1996-1997 01 - On Board Diagnostic (OBD) On Board Diagnostic (OBD II) Malfunction Indicator Lamp (MIL) On Board Diagnostic (OBD II),
More informationIMPORTANT: Hoses touching the frame, body, or engine may cause system noise. Verify that the hoses do not touch any other part of the vehicle.
Page 1 of 16 BLEEDING THE POWER STEERING SYSTEM Tools Required J 35555 Metal Mityvac J 43485 Power Steering Bleeder Adapter IMPORTANT: Hoses touching the frame, body, or engine may cause system noise.
More informationL (LU4, LJ3, L88) used in Saab 9-5 ENGINE DIAGNOSTIC PARAMETERS
Catalytic Converter Monitoring P0420 Front vs. Rear O2 sensor signal Evaluated data 1,75 times FTP std 80 (unitless) Coolant temp Throttle Delta load, positive Delta load, negative Engine speed, man. trans
More informationDiagnostic Trouble Code (DTC) memory, checking and erasing
Page 1 of 49 01-12 Diagnostic Trouble Code (DTC) memory, checking and erasing Check DTC Memory (function 02) - Connect VAS5051 tester Page 01-7 and select vehicle system "01 - Engine electronics". Engine
More informationBULLETIN TESTING. Article from Honda Service News. DTC P0341: CMP Sensor A and CKP Sensor Incorrect Phase Detected. Troubleshooting Flowchart
2005 Honda Truck CR-V 4WD L4-2.4L Vehicle > ALL Diagnostic Trouble Codes ( DTC ) > Testing and Inspection > P Code Charts > P0341 BULLETIN TESTING Article from Honda Service News DTC P0341: CMP Sensor
More informationComputers and Control Systems: Symptom Related Diagnostic Procedures C Charts. Part 1 of 6. Chart C-1 (1 Of 6)
1993 Cadillac DeVille V8-300 4.9L Page 1 Computers and Control Systems: Symptom Related Diagnostic Procedures C Charts Part 1 of 6 Chart C-1 (1 Of 6) 1993 Cadillac DeVille V8-300 4.9L Page 2 Wiring Diagram.
More informationinsider info. before it can be inspected for proper emissions. Misfire, Fuel System and Component
insider info. Rough Idle On MPFI Vehicles If you encounter a rough idle complaint on any sequential injection MPFI vehicle, basic checks should be made to ensure that the correct injector wire connector
More informationI - SYSTEM/COMPONENT TESTS
I - SYSTEM/COMPONENT TESTS 1995 Volvo 850 1995 ENGINE PERFORMANCE Volvo - System & Component Testing 850 INTRODUCTION NOTE: In this article, Engine Control Module (ECM) may also be referred to as Engine
More informationTHE witech SOFTWARE LEVEL MUST BE AT RELEASE **15.04** OR HIGHER TO PERFORM THIS PROCEDURE.
2014 RAM 3500 HD 6.7L Eng Big Horn FLASH: 6.7L DIAGNOSTIC AND SYSTEM IMPROVEMENTS TECHNICAL SERVICE BULLETIN Reference Number(s): 18-045-15, Date of Issue: May 20, 2015 CHRYSLER: 2014 Ram 2500 Pick Up
More informationDH - RAM 1500/2500 PICKUP - 6.7L CUMMINS TURBO DIESEL
007 - DH - RAM 500/500 PICKUP - 6.7L CUMMINS TURBO DIESEL U004-CAN B BUS (-) CIRCUIT OPEN For a complete wiring diagram, refer to the Wiring Information. When Monitored: With the ignition on and battery
More information5 CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
360 1NZ-FXE EINE CONTROL SYSTEM SFI SYSTEM 5 CHECK HARNS AND CONNECTOR (A/F SENSOR - ECM) Wire Harness Side A/F Sensor Connector Disconnect the A5 A/F sensor connector. A5 HT AF+ +B Front View E5 A085153E07
More informationFuel System Diagnosis
Page 1 of 6 2001 Chevrolet Malibu Malibu (VIN N) Service Manual Engine Engine Controls - 3.1L (LG8) Diagnostic Information and Procedures Document ID: 704675 Fuel System Diagnosis System Description When
More informationELECTRONIC FUEL INJECTION
Table of Contents ELECTRONIC FUEL INJECTION Section 3B - Troubleshooting and Diagnostics TROUBLESHOOTING AND DIAGNOSTICS Specifications........................... 3B-1 Special Tools...........................
More informationBefore performing symptom troubleshooting, check for power train DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
2003 Honda Civic 1.7L Eng LX Component AC PRESSURE SENSOR A/C Pressure Switch Circuit Troubleshooting NOTE: Do not use this troubleshooting procedure if any of the following items are operative; condenser
More informationSTARTER CIRCUIT TROUBLESHOOTING
2000 Honda Accord EX Sedan V6-3.0L Vehicle > Starting and Charging > Starting System > Starter Motor > Testing and Inspection > Component Tests and General Diagnostics STARTER CIRCUIT TROUBLESHOOTING Starter
More informationDTC P0440 Evaporative Emission Control System Malfunction
DIAGNOSTICS EINE DI81 DI1JZ07 DTC P0440 Evaporative Emission Control System Malfunction CIRCUIT DESCRIPTION The vapor pressure sensor, VSV for canister closed valve (CCV) and VSV for pressure switching
More informationIntake manifold change-over
Page 1 of 10 24-67 Intake manifold change-over This test should only be performed if there is a performance deficiency. The intake manifold switches from the long intake path to the short one at approx.
More informationEvaporative Emissions
Page 1 of 6 Published : Apr 8, 2005 Evaporative Emissions 4.4L V8 Evaporative Emissions Component Layout Item Part Number 1 - Fuel filler head 2 - DMTL pump filter (NAS only) 3 - Fuel tank vent hose to
More informationP0777-SECONDARY PRESSURE SOLENOID STUCK ON (LOW PRESSURE)
009 - MK - JEEP COMPASS/PATRIOT -.0L 4 CYL DOHC 6V DUAL V.V.T. P0777-SECONDARY STUCK ON (LOW ) / LINE SECONDARY ON/OFF 3 4 T0 DG/LB T9 T9 T60 YL/DB YL/LB YL/GY C C 3 C 4 C LINE SECONDARY ON/OFF MODULE-
More information