Standards Are Fit For Use Standard must be free of leaks, dents and seals must be intact
|
|
- Mervin Dustin Sims
- 6 years ago
- Views:
Transcription
1 Test Procedures for Inspecting Fuel Dispensers (90 liters/min or less) 1. Standards 2. Device Use 3. Visual Exam 4. Performance 5. Sealing Physical Standards Physical Standards Certified Within Prescribed Period (R56) Test Measures must be certified every 1 year Provers with valves must be certified every 4 years (some 2 years) Electronic thermometers must be certified every 2 years Standards Are Fit For Use Standard must be free of leaks, dents and seals must be intact Wet Before Use 20 second drain time for 20 liters measures (STP22) Device Use Approval Review Device must be in every respect identical to the device referenced in the approval and be suitable for its intended use. (NOA, A8) Approval Number Approval number must be stamped on device. (A8, R17) Initially Inspected All devices must be initially inspected before use in trade and bear initial inspection markings (A8, R29, Bulletin V -8 & V-9) Flow Rates within Approved Range Device must not be used below minimum approved flow rate or be capable of operation at flows in excess of maximum approved rate (NOA, R271, R280, R290, STP21)
2 Visual Exam - Marking & Labeling Markings Present & Located Correctly Plate affixed to device with manufacturer name, model, serial number, approval number(s), min/max flow rate, Volume Corrected to 15 C, usage restrictions, etc. (NOA, R18, R21, R70) Markings Permanent Markings on plates should be die stamped. Other markings non-removable end weather resistant (R18) Unit of Measurement and Monetary Markings Liters, Dollar signs, decimals, cents per liter, $ per liter are correct location and size (R18, R135, R136, R137) Number of Outlets Appropriate If more than one outlet, appropriate signs, lights and solenoids (R282) Printer Tickets Appropriate to the printer and printed with adequate number of digits, decimals (R126, R149, Bulletin V -7) Printer Tickets Information printed as required i.e. net volume, liters, $ total and price per liter (R129, R295, SVM1-27, Bulletin V-20) Visual Exam - General Installed as per NOA &Manufactured Instructions Approval must be checked for any installation inspections. (NOA, R68, R69, R70) Register Visible To Customer The primary register must be visible to customer at all times (R143, R144)
3 Minimum Graduation and Sufficient Digits in Total Price Volume display - five digits and 0.01 L or finer Total $ - sufficient digits to compute max liters x max $/liter (R68, R126, SVM1-20 &21, Bulletin V -7) Linearization Factors If applicable, adjacent linearization factors must not vary by more than 0.25%. (SVM1-10) ATC On Seasonal and partial ATC conversions not allowed. (Bulletin V -19, SVM1-27) Visual Exam - Piping Air Elimination Ensure air eliminator present (if applicable), not plugged or restricted. (R274, R276, R279) Filter / Strainer Ensure filter or strainer installed immediately upstream from meter. (R277) ATC Sensor and Test Well Installed Appropriately Test well must be installed immediately adjacent to the probe, must be within one metre of the meter. Thermal well must be of appropriate design and retain fluid. No pumps, valves, etc between probe and meter. (SVM2-23, 24, 25) Performance Return to Zero Test STP1 All means of registration (gross, net, total $) must return to zero. (R249, R252, R256, STP1)
4 Interlock Test STP2 The dispenser must be interlocked so that it cannot deliver product unless the display have been returned to zero. The dispenser must also prevent the delivery of another product once the delivery has started (or more than 100ml has been dispensed), unless reset to zero. (R252, R253, R254, SVM1-12, SVM1-17) Segment Test STP3 Segment must all go on and all go off during test or prevent use if faulty. (SVM1-12) Prover Shell Correction STP23 Although not generally done for 20 litre measures, correction must be made if temperature of product in prover is different than 15 C. (Bulletin V-17) Slow Flow Test STP4 For 20 litres must be within 50 ml (in factory) and 100 ml (in field). (R261, R262, R265) Fast Flow Test STP5 For 20 litres must be within 50ml ( in factory) & 100ml ( in field). If an adjustment is required the results must be within 20ml. (R261, R262, R265, R35) Repeatability Test STP7 Required if the difference between the fast and slow exceeds 100 ml Three fast runs - all runs must be within 20 ml (factory) or 40 ml (field) (R138, R263) Agreement Between Registrations STP9 Electronic registers having the same increment of registration must agree exactly. Electronic registers having different increments of registration must agree within 0.6 times the larger increment. (R139, R2 92, R293, SVM1-20, Bulletin V-7 and V-20)
5 Computed Value Test STP10 Total dollar computed must be in agreement with the volume registered multiplied by price per litre to the nearest cent. (R140, SVM1-13, SVM1-21, SVM1-26) Pulser Backlash Test STP14 Test to ensure that repetitive (5 times) starting and stopping does not affect accuracy, result must be within the applicable limit of error. (R265, SVM1-20, SVM1-35) Prepay Test STP17 The dispenser must not deliver less than the preset amount and can go over by up to 50ml. (SVM1-32, SVM1-33) Anti drain valve Test STP11 The nozzle must have a functioning anti-drain valve that prevents the hose from being drained between transactions. lf any appreciable loss, close nozzle valve, drain measure, turn on dispenser and perform another fast flow test, must be within the applicable limit of error. (R286) Hose Expansion Test STP12 Perform fast run and turn off dispenser. Open nozzle to relieve hose pressure. Drain measure and retest dispenser Device must be a within 100 ml on 20 litres. (R238, R265, R272, Bulletin V-1) Delivery cross-over Test STP15 For single product twin dispenser product must not be capable of delivery from a turned off side when the other side is operating. Where a common pump supplies many dispensers product must not be capable of delivery from an off dispenser, when the pump is turned on through the use of another dispenser. (R68, R254) Blend Test STP16 Performance test required on the two extreme ranges of products. Tests on mid ratios and blends is optional. No separate test required on mid-blends. Must be within the applicable limit of error. (R265, SVM1-16)
6 ATC Test STP18 Minimum run of 20 litres required for ATC test. Limit of error 0.5 C (in factory) and 1C (in field) Ensure proper API tables used for particular product. (R270, SVM2-20) ATC Probe Failure Test STP19 To be applied by service technician during manufacturer (factory) initial inspections Disconnect probe during delivery. Product flow must cease immediately or within a few litres.(svm2-11) EM /RF interference Test STP20 The device must not be affected in any way by EM or RF found to be emitted in the general area of the device.(r66, R68, R124,R142S, SVM1-31) Sealing Meter Calibration Measuring element / calibrator must be sealed. R235 Electronic Calibration Any means of adjusting the calibration of the register must be sealed. SVM1-8,9 ATC Adjustment Any means of adjusting lhe ATC must be accessible and sealed. SVM2-7 ATC Sensor ATC sensor must be sealed to prevent removal, SVM2-l0 Flow Control Valve If applicable, f low control valve must be sealed to limit flow to maximum. R280
7 Note: More detailed Field Inspection Test Procedures are found at: More W&M Legislation links are found at: Contact info: Stefan Luca FUELMEASURE INC. Tel:(519) Fax:(866)
National Type Evaluation Program. Checklists and Test Procedures for Retail Motor Fuel Dispensers
National Type Evaluation Program Liquid Measuring Devices Checklists and Test Procedures for Retail Motor Fuel Dispensers 7. Indicating and Recording Elements Code Reference: G-S.5.1. and G-UR.1.1. General
More information6" Steel Model G6. Smith Meter Rotary Vane PD Meters. Features. Operating Specifications Maximum Flow Rate. Options
SPECIFICATIONS 6" Steel Model G6 Bulletin SS01014 Issue/Rev. 1.0 (4/18) Smith Meter Rotary Vane PD Meters The Smith Meter Model G6 Meter is a 6", double-case, straight-through rotary vane type positive
More informationTitle: Terms and Conditions for the Approval of Coriolis Liquid Meters. Effective Date: Page: 1 of 9 Revision: 1
Effective Date: 2012-12-01 Page: 1 of 9 Revision: 1 1.0 Application These terms and conditions apply to Coriolis metering assemblies and to metering installations used in trade 1. 2.0 Definitions In this
More informationMETROLOGICAL AND TECHNICAL REQUIREMENTS FOR LIQUID MEASURING DEVICES SUBJECT TO LEGAL METROLOGY CONTROL
SADCMEL DOCUMENT 5 METROLOGICAL AND TECHNICAL REQUIREMENTS FOR LIQUID MEASURING DEVICES SUBJECT TO LEGAL METROLOGY CONTROL Page 1 of 8 FOREWORD This document covers metrological and technical requirements
More informationBENNETT CNG DISPENSER MAINTENANCE SCHEDULE
BENNETT CNG DISPENSER MAINTENANCE SCHEDULE Serial #: DIN #: Company Name: CAUTION: Only trained personnel may work on dispensers. CAUTION: The emergency shut off valve if installed must be closed. CAUTION:
More informationCode Requirements for ASTs at Motor Vehicle-Dispensing Stations
Code Requirements for ASTs at Motor Vehicle-Dispensing Stations This table compares aboveground storage tank requirements in the 2015 edition of, to the 2015 International Fire Code (). Please note that
More information3" Steel Model E3. We put you first. And keep you ahead.
SPECIFICATIONS MEASUREMENT SOLUTIONS 3" Model E3 Bulletin SS01016 Issue/Rev. 1.1 (2/15) We put you first. And keep you ahead. SMITH METER PD METERS The Smith Meter Model E3 is a 3", double-case, straightthrough
More informationSmith Meter PD Meters 3" Steel Model E3
Smith Meter PD Meters 3" Steel Model E3 Specifications Bulletin SS01016 Issue/Rev 1.0 (8/13) The Smith Meter Model E3 is a 3", double-case, straight-through (S1 through S7) or angle-type (A1 and A3), rotary
More informationGREASE CONTROL GUNS GREASE CONTROL GUNS Grease control gun Grease control gun with rigid stem and 3 jaw connector ( ).
MEASURE AND CONTROL GREASE CONTROL GUNS AND ACCESSORIES GREASE METERS OIL CONTROL GUNS AND ACCESSORIES OIL METERS OIL METER ACCESSORIES FLUID CONTROL GUNS FLUID METERS HIGH FLOW IN LINE METERS ADVANCED
More informationIndustrial Turbo Meters, Sizes 2" through 6"
Industrial Turbo Meters Sizes 2" through 6" TUR-UM-00530-EN-19 (October 2014) User Manual Industrial Turbo Meters, Sizes 2" through 6" User Manual CONTENTS Scope of the Manual 5 Specifications 5 Product
More informationMODELS: 800 Series (Reset, Preset, Ticket Printing) 600 Series (Reset) 157 (Non-Resettable Totalizer)
TS-301 Rev. A Mechanical Registers Models: 157, 600 Series and 800 Series MECHANICAL REGISTERS MODELS: 800 Series (Reset, Preset, Ticket Printing) 600 Series (Reset) 157 (Non-Resettable Totalizer) SPECIFICATIONS
More informationTypes and 52.20, Specialized test procedure Milk receiving and milk pick-up metering systems
Types 52.10 and 52.20, Specialized test procedure Milk receiving and milk pick-up metering systems Category: Volume Part: 4-STP Section: 28 Publication date: 2017-06-08 Revision number: 4 Application Milk
More informationEPO No. 28. Examination Procedure Outline (EPO) for. Compressed Natural Gas (CNG) Retail Motor-Fuel Dispensers
EPO No. 28 Examination Procedure Outline (EPO) for Compressed Natural Gas (CNG) Retail Motor-Fuel Dispensers It is recommended that this outline be followed as minimum criteria for examining retail motor-fuel
More informationMECHANICAL REGISTERS
TS-614(H) TS-301(E) MECHANICAL REGISTERS MODELS: 800 Series (Reset, Preset, Ticket Printing) 600 Series (Reset) 157 (Non-Resettable Totalizer) Mechanical Registers record the volume of liquid passing through
More informationProduct Loss During Retail Motor Fuel Dispenser Inspection
Product Loss During Retail Motor Fuel Dispenser Inspection By: Christian Lachance, P. Eng. Senior Engineer - ment Engineering and Laboratory Services ment Canada Date: Product Loss During Retail Motor
More informationAMB100L-im-issue INSTRUCTION MANUAL 240V DIESEL MINI BOWSER AMB100L AMB100L
-im-issue1-2015 INSTRUCTION MANUAL 240V DIESEL MINI BOWSER INSTRUCTION MANUAL 240V DIESEL MINI BOWSER INTRODUCTION Thank you for purchasing a Macnaught 240V Diesel Mini Bowser (100 l/min) The Macnaught
More information1. All aircraft fueling equipment shall have a Filter/Separator or a Full-Flow Fuel Monitor.
No. 401 STANDARD SAFETY PROCEDURES STANDARD EQUIPMENT LIST FOR FUELING VEHICLES OBJECTIVE: To ensure the safety of property and personnel, the following minimum operational/equipment list, for each fueling
More informationModel G6-S3. Repeatability ±0.02%
Issue/Rev. 0.6 (2/07) Smith Meter TM PD Rotary Vane Meter 6" Steel Model G6 Specifications Bulletin SS01014 The Smith Meter TM Model G6 Meter is a 6", double-case, straight-through (S3 through S8) or angle-type
More informationCounters, Printers, Preset Counters
SPECIFICATIONS Counters, Printers, Preset Counters Bulletin SS01100 Issue/Rev. 0.3 (10/17) Smith Meter PD Meter Accessories High Capacity and Large Numeral Counters Model 600 and 900 Series Non-Reset CountersModel
More informationTesting CNG. Retail Motor Fuel Dispensers
The s of Testing CNG Retail Motor Fuel Dispensers 1 Certain commercial entities, equipment, or materials may be identified in this presentation in order to describe a procedure or concept adequately. Such
More informationSTP-MLD. Installation and Owner s Manual
The Leader in Submersible Technology Mechanical Leak Detector STP-MLD STP-MLD-D STP-MLD-E Gasoline Diesel Flexible Pipe STP-MLD STP-MLD Installation and Owner s Manual 4805 Voges Rd., P.O. Box 139 McFarland,
More informationHigh Accuracy Mechanical Fuel meter FM-100
INSTRUCTION MANUAL S190, Rev A High Accuracy Mechanical Fuel meter FM-100 Congratulations on purchase of this World Class High Accuracy Mechanical Fuel Meter! Worldclass Mechanical Fuel Meter, extremely
More informationForensic Sciences Chapter ALABAMA DEPARTMENT OF FORENSIC SCIENCES ADMINISTRATIVE CODE CHAPTER IGNITION INTERLOCK RULES
Forensic Sciences Chapter 370-3-1 ALABAMA DEPARTMENT OF FORENSIC SCIENCES ADMINISTRATIVE CODE CHAPTER 370-3-1 IGNITION INTERLOCK RULES TABLE OF CONTENTS 370-3-1-.01 Ignition Interlock Rules 370-3-1-.01
More informationSKY-WEIGH HELICOPTER CARGO HOOK LOAD MONITORING SYSTEM. User Guide Quality Industrial Weighing and Force Measurement Equipment
MSI150X SKY-WEIGH HELICOPTER CARGO HOOK LOAD MONITORING SYSTEM User Guide Quality Industrial Weighing and Force Measurement Equipment Measurement Systems International Page 2 MSI-150X Sky-Weigh User Guide
More informationVGT Service Data Sheet 1 of 12
VGT Service Data Sheet 1 of 12 WARNING Turbochargers can be hazardous when not used as specified by the manufacturer. To prevent damage and personal injury: Always use the turbocharger part number specified
More informationRD712 & RD712XL Remote Displays. Model 615 / 615XL Indicator User s Manual
RD712 & RD712XL Remote Displays Model 615 / 615XL Indicator User s Manual EUROPEAN COUNTRIES WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which
More informationIMPORTANT!!!! Read this manual before attempting any installation, wiring or operation.
Industrial Turbo Meters Sizes 2" through 6" Installation & Operation Manual IMPORTANT!!!! Read this manual before attempting any installation, wiring or operation. BadgerMeter,Inc. IOM-003-15 Part No.
More informationInstallation & Operation Manual. IMPORTANT: This manual contains important information. READ AND KEEP FOR REFERENCE.
Elecronic Preset Meter 2 Industrial Handheld Series Model EPM2-IND Standard Series IMPORTANT: This manual contains important information. READ AND KEEP FOR REFERENCE. IOM-139-02-EN (1-12) 53400-139 Rev.
More informationLACT MEASUREMENT. Total Head = Or PSI = S.G. 2.31
LACT MEASUREMENT Prepared By: Ken A. Steward. P.E. Linco-Electromatic, Inc. 4580 West Wall Street Midland, Texas 79703 The Operation of L.A.C.T. Units The simplest approach to the understanding of the
More informationThe RCS-6V kit. Page of Contents. 1. This Book 1.1. Warning & safety What can I do with the RCS-kit? Tips 3
The RCS-6V kit Page of Contents Page 1. This Book 1.1. Warning & safety 3 1.2. What can I do with the RCS-kit? 3 1.3. Tips 3 2. The principle of the system 2.1. How the load measurement system works 5
More informationBennett Pump Company
Bennett Pump Company Mechanical & Hydraulic Service Manual READ THIS BOOK This book has important information for safe installation and operation of this equipment. Read and understand this book before
More informationInstallation and Setup Instructions
Installation and Setup Instructions Model: Master Version: MMR80-40S Date of issue: 22 May 2009 Compac Industries Ltd P O Box 12-417 Penrose Auckland New Zealand Ph 64 9 5792 094 Fax 64 9 5790 635 www.compac.co.nz
More informationLCB File No. R PROPOSED REGULATION OF THE STATE ENVIRONMENTAL COMMISSION
LCB File No. R130-09 PROPOSED REGULATION OF THE STATE ENVIRONMENTAL COMMISSION EXPLANATION Matter in italics is new; matter in brackets [omitted material] is material to be omitted. AUTHORITY: NRS 445B.210,
More informationStandard Calibration Certificate
Mettler Toledo Service Business Unit Laboratory 1900 Polaris Parkway Columbus, OH 43240 1-800-METTLER Customer Standard Calibration Certificate Company: ABC Pharma Incorporated Address: 1432 East 9th Street
More informationModule 13 Rate-controller functions and settings Getting the best out of the functions available
SPRAY APPLICATION MANUAL FOR GRAIN GROWERS Module 13 Rate-controller functions and settings Getting the best out of the functions available Graham Betts and Bill Gordon PAGE 2 Key points A rate controller
More informationfusion RF Control Handle
SERVICE BULLETIN SB3088 Rev B 04/15 fusion 2.4 - RF Control Handle Model 3331-021...2.4 GHz RF Control Handle Thoroughly read and understand this manual before installing, operating or servicing this equipment.
More informationRIGID TANKER INSPECTION CHECKLIST
PASS2LOAD INSPECTION P2L label # RIGID TANKER INSPECTION CHECKLIST AIL Location: AIL No: Inspector Name: Rego No: DG No: Vehicle Owner: This checklist must be completed in conjunction with the SLP Operating
More informationStandard Calibration Certificate
Mettler Toledo Service Business Unit Laboratory 1900 Polaris Parkway Columbus, OH 43240 1-800-METTLER Customer Standard Calibration Certificate Company: Address: Allied Food Processing 3433 West High Street
More informationFL-100-R (109) Operations and Installation Manual
Page 1 of 23 All specification subject to change 2002-2005 FL-100-R (109) Operations and Installation Manual This manual is certified for use with instrument serial number ASL000000 Use of this manual
More informationCHAPTER 9 : TYPE II TEST ON SI ENGINES (VERIFYING CARBON MONOXIDE EMISSION AT IDLING)
CHAPTER 9 : TYPE II TEST ON SI ENGINES (VERIFYING CARBON MONOXIDE EMISSION AT IDLING) 1 Scope : This Chapter describes the procedure for the TYPE II test for verifying carbon monoxide emission at idling
More informationInstallation & Calibration
Installation & Calibration ED2-AT Series SkidWeigh System Lift Truck On-board Check Weighing With Accumulative Load Weight Total ED2-AT Series SkidWeigh V.1.1 General Installation Guide This ED2-AT Series
More informationDESIGN, OPERATION & MAINTENANCE OF L.A.C.T. UNITS
DESIGN, OPERATION & MAINTENANCE OF L.A.C.T. UNITS INTRODUCTION The two most common methods of measuring the volume of petroleum liquids are tank gauging and liquid metering. The problems associated with
More informationfactsheet Field Sprayer Calibration Introduction Pre-Calibration Checklist Using a Calibration Bottle
Field Sprayer Calibration Introduction It is important to properly calibrate your sprayer for maximum performance. Improper spray application can be costly in terms of poor pest control, crop injury and
More informationOPERATIONS MANUAL M-520. Please take the time to read these instructions before starting to use the scales. Page 1
OPERATIONS MANUAL M-520 Please take the time to read these instructions before starting to use the scales Page 1 Contents Power supply 3 Specifications 3 Maintenance and general care 3 Key functions 4
More informationLorri Grainawi Steel Tank Institute. PA NISTM April 25, 2013 Harrisburg, PA
Lorri Grainawi Steel Tank Institute PA NISTM April 25, 2013 Harrisburg, PA PEI/RP1200-12 ------------------------------------------------------ 1. Introduction 2. Definitions 3. Safety 4. Tank Secondary
More information25 mm (1 in), 38 mm (1-1/2 in) & 50 mm (2 in) TYPE S FLOWMETERS WITH MODEL 157 AND 800 SERIES REGISTERS
TS- Rev. B Type S lowmeters 1, 1 1 2 & 2 mm (1 in), mm (1-1/2 in) & mm (2 in) TYPE S LOWMETERS WITH MODEL 7 AND 8 SERIES REGISTERS 1-1/2" Type S with Model 7 Register SPECIICATIONS 1" Type S with Model
More informationINSTALLATION INSTRUCTIONS FOR THE TRUCK MOUNTED VIPER ADDITIVE INJECTION SYSTEM GTP-8776C
INSTALLATION INSTRUCTIONS FOR THE TRUCK MOUNTED VIPER ADDITIVE INJECTION SYSTEM GTP-8776C This additive injection system was designed to be used with five gallon jug of additive. The system is supplied
More informationMECHANICAL and HYDRAULIC SERVICE MANUAL READ THIS BOOK
READ THIS BOOK This book has important information for the safe maintenance and service of this equipment. Read and understand this book before applying power. Keep this book and tell all service technicians
More informationPh: (07) Fax: (07) Pump Manual
sales@scintex.com.au www.scintex.com.au Ph: (07) 3137 0135 Fax: (07) 3041 0541 Pump Manual 12V 75LPM Vane Pump & Vane Pump Station SPEP12V75 & SP12VFS75 SPEP12V75 SP12VFS75 Parts List No. Part Name QTY
More informationCode Requirements for ASTs at Motor Vehicle-Dispensing Stations
Code Requirements for ASTs at Motor Vehicle-Dispensing Stations This table compares aboveground storage tank requirements in the 2008 edition of NFPA 30A, and the 2006 International Fire Code (IFC). Please
More informationSTP-MLD+ Installation and Owner s Manual. Manual # Revision Date Changes from previous revision
STP-MLD+ Installation and Owner s Manual Manual # Revision Date Changes from previous revision 400439002 3 Sept. 2014 Changed MLD+AG description to 85% ethanol Franklin Fueling Systems 3760 Marsh Rd. Madison,
More informationNC State University Design and Construction Guidelines Division 23 Energy Management
1.1 Purpose A. The following guidelines provide the methodology and requirements to assure that designs meet NC State standards for campus utility metering. 2.1 General Requirements A. Meters shall have
More informationPRECISION UK Ltd DUPLEX AGSS PLANT
DUPLEX AGSS PLANT Contents Page Section Page Product Description General 3 AGSS Plant 3 AGSS Remote Switch 3 Operation General 4 Safety General 5 Installation General 5 Mechanical 5 Electrical 7 Wiring
More informationMR 5-30 or MR 5-30N Series Fuel Meter Owner s Manual
SAVE THESE INSTRUCTIONS MR 5-30 or MR 5-30N Series Fuel Meter Owner s Manual TABLE OF CONTENTS General Information...2 Installation...3 Operation...3 Calibration...4 Maintenance...5 Troubleshooting...6
More informationNT-500 Technical Support Guide. For use by qualified company approved Technicians
NT-500 Technical Support Guide For use by qualified company approved Technicians INTRODUCTION The NT-500 is designed to offer the full range of features required to perform radiofrequency denervation The
More informationEC type-examination certificate UK/0126/0072 Revision 2
UK/0126/0072 MI-005 EC type-examination certificate UK/0126/0072 Revision 2 issued by: The National Measurement Office Notified Body Number 0126 In accordance with the requirements of the Measuring Instruments
More informationUK Weighing Federation Technical Articles
GLOSSARY The source of each definition is identified by the superscript number and listed out in full at the end of this glossary. Accuracy classification (1) classification as a Class I, Class II, Class
More informationTable of Contents. 1.0 INFORMATION 1.1 Introduction About This Manual Helpful Hints and Warnings Service and Product Support
Contents Table of Contents 1.0 INFORMATION 1.1 Introduction 1.1.1 About This Manual 1.1.2 Helpful Hints and Warnings 1.1.3 Service and Product Support 1.2 Product Information 1.2.1 System Components 2.0
More informationH. HERMANN EHLERS GMBH
H. HERMANN EHLERS GMBH Fördern - Messen - Regeln - Dosieren - Verdichten Ingenieurbüro - Werksvertretungen Positive displacement meters series - - An der Autobahn 45 28876 Oyten Tel. 04207/91 21-0 Fax
More informationStandard Specification for ASTM Hydrometers 1
Designation: E 100 03 Standard Specification for ASTM s 1 This standard is issued under the fixed designation E 100; the number immediately following the designation indicates the year of original adoption
More informationSmith Meter Truck Meter Packages Specifications
Issue/Rev. 0.4 (8/12) P Meter Smith Meter Truck Meter Packages Specifications ulletin SS01095 TP (Ticket Printer) LN (Large Numeral ounter) Preset ounter Air Eliminator/ Strainer Faucet P Meter Smith Meter
More informationLesson 4: Fuel Costs and Fuel Economy
Lesson 4: Fuel Costs and Fuel Economy Fuel Economy (Fuel Consumption) A major operating cost of a vehicle is the gasoline. Different vehicles require different amounts of gasoline to drive the same distance.
More informationTruck Scale Description
NUWEIGH RIDGE SERIES TRUCK SCALE DATA SHEET Description The NUWEIGH Ridge Series has been manufactured to the highest standards and will provide you with a long term solution, the truck scale has been
More informationWarranty conditions on DHOLLANDIA tail lifts Date :
tail lifts Date : 1. Abbreviations DHO = or her official national agent / distributor HTL = Hydraulic tail lift CV = (Commercial) vehicle 2. Period 2.1 - The warranty period lasts 12 months from the day
More informationTires are available in a number of sizes and tread patterns dependent on the vehicle usage. Tire sizes are as follows:
Published: Jan 26, 2005 Wheels and Tires GENERAL A number of alloy wheel and tire size combinations are available. A Tire Pressure Monitoring System (TPMS) is also available. This system monitors the pressure
More informationLM-200 MECHANICAL LUBE METER Owner s Manual
LM-200 MECHANICAL LUBE METER Owner s Manual To the owner Congratulations on receiving your GPI Mechanical Lube Meter. We at GPI are pleased to provide you with a Lube Meter designed to give you maximum
More informationAir Handling Unit Construction Checklist
Air Handling Unit Construction Checklist Project: Date: AHU Tag: Location: Submittal / Approvals Submittal. The above equipment and systems integral to them are complete and ready for functional testing.
More informationAccu-Guard Compact + Ideal for Industrial / Manufacturing Applications or Shop Environments. Take complete CONTROL of your fluid inventory.
Accu-Guard Compact + Take complete CONTROL of your fluid inventory. Alemite s all-new Accu-Guard Compact + allows you to easily manage your entire fluid inventory. This state-ofthe-art fluid management
More informationSafety cap. Measuring probe. Seal. Operating principle. Advantages of balanced circuits. Balanced circuits have the following principal benefits:
Balancing valve, fixed orifice 0 series CALEFFI 0/ NA ACCREDITED ISO 900 FM ISO 900 No. 000 Function Product range Caleffi 0 series low lead, manual balancing valves are used to measure and adjust the
More informationTECHNICAL MANUAL CALIBRATION PROCEDURE FOR MANUALLY OPERATED TORQUE WRENCHES 6% TO 20% (GENERAL)
TECHNICAL MANUAL CALIBRATION PROCEDURE FOR MANUALLY OPERATED TORQUE RENCHES 6% TO 20% (GENERAL) Distribution Statement - Distribution authorized to U. S. Government agencies and their contractors for official
More informationPETROL. Double Case PD Flowmeters. Trust in us Our Quality Counts. Technical Bulletin. PETROL Instruments S.r.l.
Double Case PD Flowmeters Technical Bulletin The trusted specialist manufacturer of high precision instruments that relies upon the accurate measurement of fluid volumes Trust in us Our Quality Counts
More informationInfraCal TOG/TPH Analyzer,
InfraCal TOG/TPH Analyzer, Model CVH Calibration www.wilksir.com Calibration Oil Heavy hydrocarbon No volatiles No Additives Mixing Standards Volume/volume ppm Oil Solvent 400 40ul 10 ml 300 30ul 10 ml
More informationElectronic Rising Plate Meter. Instruction Manual FARMWORKS. Equations for Rising Plate Meter. FARMWORKS Precision Farming Systems Technical Support
Equations for Rising Plate Meter For your convenience the following are the current equations promoted by Dexcel since May 2001 Please refer to Page 8 of this booklet on how to alter and select the appropriate
More informationHeating and Gas Installations - December 2014
This is an example of good practice maintenance specifications. It is not exhaustive and should only be used to assist with facilities management or specification of a maintenance contract. Emergency Gas
More informationZTM AND ZTMB ZENNER TURBINE METERS INSTALLATION, MAINTENANCE AND SERVICING
ZTM AND ZTMB ZENNER TURBINE METERS INSTALLATION, MAINTENANCE AND SERVICING INSTALLATION 1. The meter is intended for measuring potable, cold water in one direction. 2. The meter is to be installed in a
More informationDate. Director c/o Petroleum Storage Program Manitoba Conservation and Water Stewardship 1007 Century Street Winnipeg, MB R3H 0W4
Date Director c/o Petroleum Storage Program Manitoba Conservation and Water Stewardship 1007 Century Street Winnipeg, MB R3H 0W4 To the Attention of the Director: Re: Insert Company Name Request for Variance
More informationTYPE MP OSCILLATING PISTON FLOWMETER
TS-150 (G) TYPE MP OSCILLATING PISTON FLOWMETER Flow Rates of 3.8 to 1,140 Liters/Min. (1 to 300 gpm) Accuracy of ±0.5% of Rate ±0.1% Repeatability Magnetically Coupled Output Shaft Proven Reliable Oscillating
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL MODEL T575N TEMPERATURE COMPENSATED TOTALIZER/PRINTER DOC#: MN-T575N SPONSLER, INC. Liquid and Gas Flow Measuring Devices and Controls LBS ON OFF TRUCK TOTALIZER MODEL T575N
More informationStandard Features and Options
Page 1 of 5 For: Indicating Element Digital Electronic Models: 200, 205, 210, 210-F, 210-FE, 212-G, 212-G, 215, 220 and 225 n max : 10 000 Accuracy Class: III / III L Submitted By: 203 East Daugherty Street
More informationNGW & HGW SERIES CONTENTS OPERATION MANUAL CAUTIONS HIGH RESOLUTION MULTI-FUNCTION DIGITAL SCALE 1. INSTALLATION 2. SPECIFICATIONS
NGW & HGW SERIES HIGH RESOLUTION MULTI-FUNCTION DIGITAL SCALE CONTENTS CAUTIONS 1. INSTALLATION 2. SPECIFICATIONS OPERATION MANUAL 3. KEYBOARD LAYOUT AND DESCRIPTION 4. INITIAL SETUP PLEASE READ THIS MANUAL
More information6109A / 7109A. Portable Calibration Baths. Four times more calibration throughput with twice the accuracy of Micro-Baths and dry-block calibrators
6109A / 7109A Portable Calibration Baths Four times more calibration throughput with twice the accuracy of Micro-Baths and dry-block calibrators Portable calibration baths designed for clean process applications
More informationNozzles Lane-oriented and High-hose Attachment Downloadable Software. Endress & Hauser LPG Mass DN15 Diesel Exhaust Fluid (DEF)
Page 1 of 11 For: Retail Motor Fuel Dispenser (RMFD) Dispenser, Electronic Computing Models: NA, NPA, NPB, NPC and Field Upgrade Modules Gilbarco Part Number ENC-DEF-RF Generic Names: Encore 500, Encore
More informationMECHANICAL FUEL METER. FM-100 and FM-200 Series Owner s Manual
MECHANICAL FUEL METER FM-100 and FM-200 Series Owner s Manual To the owner Congratulations on receiving your GPI Mechanical Fuel Meter. We at GPI are pleased to provide you with a fuel meter designed to
More informationSTP-MLD Installation and Owner s Manual
STP-MLD Installation and Owner s Manual 2006 400439001 Rev. 6 Franklin Fueling Systems 3760 Marsh Rd. Madison WI 53718 USA Tel: +1 608 838 8786 800 225 9787 Fax: +1 608 838 6433 www.franklinfueling.com
More informationChapter 2. The Vehicle-Tank Metering System
Chapter 2 The Vehicle-Tank Metering System Chapter Objectives Upon completion of this chapter, you should be able to: 1. Describe the vehicle-tank metering system, its uses, and its relation to other liquid-volume
More informationIdle Air Control (IAC) System Diagnosis
Page 1 of 6 2002 Chevrolet Tahoe - 4WD Avalanche, Escalade, Suburban, Tahoe, Yukon VIN C/K Service Manual Engine Engine Controls - 4.8L, 5.3L, and 6.0L Diagnostic Information and Procedures Document ID:
More informationRequirements and Responsibilities for Fire Pump Packages
Philosophy The performance and long term reliability of a fire pump is directly related to proper assembly and installation of the fire pump package components. For this reason FM Approvals requires that
More informationTable of Contents. 1.0 INFORMATION 1.1 Introduction. 1.2 Product Information. 2.0 INSTALLATION 2.1 Pre-Installation. 2.2 Component Installation
Contents Table of Contents 1.0 INFORMATION 1.1 Introduction 1.1.1 About This Manual 1.1.2 Helpful Hints and Warnings 1.1.3 Service and Product Support 1.2 Product Information 1.2.1 System Components 2.0
More informationSAC SERIES CONTENTS TRIPLE-INTERVAL HIGH PRECISION COUNTING SCALE OPERATION MANUAL 1. INSTALLATION 2. SPECIFICATIONS
CONTENTS SAC SERIES TRIPLE-INTERVAL HIGH PRECISION COUNTING SCALE 1. INSTALLATION 2. SPECIFICATIONS 2.1 GENERAL SPECIFICATIONS 2.2 MINIMUM PIECES, WEIGHT APPLIED & SAMPLE SIZE WEIGHT SPECIFICATIONS OPERATION
More informationTAPE EXTENSOMETER Model CONVEX-D. Roctest Limited, All rights reserved.
INSTRUCTION MANUAL TAPE EXTENSOMETER Model Roctest Limited, 2013. All rights reserved. This product should be installed and operated only by qualified personnel. Its misuse is potentially dangerous. The
More informationInstallation, Operation, and Maintenance Manual
Installation, Operation, and Maintenance Manual Welker Flanged Liquid Sampler Model LSS-1F Drawing No.: AD478BF.1 Manual No.: IOM-140 The information in this manual has been carefully checked for accuracy
More informationOPERATOR S MANUAL X INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
OPERATOR MANUAL 635360-X INCLUDING: OPERATION, INTALLATION & MAINTENANCE ELECTRONIC PREET DIGITAL METER FOR UE WITH LUBRICATION FLUID RELEAED: 10-7-04 REVIED: 6-11-10 (REV. 03) READ THI MANUAL CAREFULLY
More informationMPT-200A SPECIFICATIONS AND OPERATING INSTRUCTIONS
MPT-200A SPECIFICATIONS AND OPERATING INSTRUCTIONS DATASHEET 1. SAFETY The MPT-200A Wire Crimp Pull Tester is a force measurement device, and as such should be operated with due caution. Operator should
More informationRML2000. Installation Manual. Measurement systems for the future, from the trusted name in metering...neptune.
M-614(C) 09/06 RML Inst. RML2000 Installation Manual IMPORTANT: To assure proper installation of this product, thoroughly review the information in this revision of the manual. Information is subject to
More informationCommissioning Manual PLATE HEAT EXCHANGER. Customer Name: Serial number: Purchase order number: Project:
Commissioning Manual PLATE HEAT EXCHANGER Customer Name: Serial number: Purchase order number: Project: Table of Contents ----------------------------------------------------------------- Page: 2 3 Name
More informationEGT-100 Operations and Installation Manual
Page 1 of 11 All specification subject to change 2002-2005 EGT-100 Operations and Installation Manual This manual is certified for use with instrument serial number ASL000000 Use of this manual with any
More informationLD Series Electronic Meters
LD Series Electronic Meters Manual and Preset Dispense Dispenses in gallons, quarts, pints and liters Easy to read LCD display with durable switches for long life Rugged engineered material for superior
More informationSECTION METERS AND GAUGES FOR HVAC PIPING
SECTION 23 05 19 METERS AND GAUGES FOR HVAC PIPING PART 1 - GENERAL 1.1 SUMMARY A. Work included: Provision of materials, installation and testing of: 1. Thermometers 2. Thermometer Wells 3. Differential
More informationLiquid Turbine Flow Meter OwnerÊs Manual
Liquid Turbine Flow Meter OwnerÊs Manual Manual LWGY-G Rev.1.0 Content 1.0 GENERAL INFORMATION... 1 2.0 SPECIFICATIONS... 2 3.0 OPERATION CONDITIONS... 3 4.0 CAUTIONS FOR INSTALLATION... 4 5.0 DIMENSION...
More informationD3000. Troubleshooting Guide
Page 1 of 6 17486-00 Rev B s3 April 2009 Contents Description Page Safety.. 3 Introduction 3 Standard External Controls, Indicators and Normal Alarm Conditions 3 Troubleshooting Table.. 4 Unable to program
More information