CAREboy Instruction Manual. Multifunctional cordless waxer and cleaner

Transcription

1 Instruction Manual Multifunctional cordless waxer and cleaner

2 PRODUCT AND PARTS SCHEMATIC DRAWING Handle Battery Spray button Charging indicator Moping waxing switch Push to open Plastic cover LED-illumination 2 Rotary plate Water level display Nozzle Moping waxing pads (2 pcs. blue, 2 pcs. green) Aluminium alloy tube Power adapter

3 SPECIFICATION SCHEUCHER CAREBOY Rated voltage Rated power Noise Battery capacity Charging time Run time Water tank capacity Dimensions Weight 14.4 V 60 W 60 db 4000 mah 3 hours > 30 min. 330 ml. 130 x 40 x 9,5 cm 3,7 kg We reserve the right to continuously change the product design and improve the product technology without notice. ATTENTION 1. Only suitable for even/smooth surfaces such as parquet, wooden floor, stone, tiles, ceramic, laminate, vinyl floor etc. Do not use on wall or window or other uneven surfaces Do not put in water or other liquid. Clean with damp cloth. 3. Do not touch the moving parts when working. 4. Put moping pads or waxing pads on the rotary plates before use. 5. Only use recommended care and cleaning products. Other products can only be used on own risk and responsibility. Do not fill in any liquids containing solvents. *This product is only for floor care. Users are responsible for error usage for this product.

4 ASSEMBLY INSTRUCTIONS 1. Install the handle 1.1. Connect the terminal of the handle to the port which is on the top of aluminum alloy tube (see picture 1). Pic Put the aluminum alloy tube into the bottom of handle. Rotate the aluminum alloy tube until it gets locked in the handle (See picture 2) 2. Install the main body 2.1. Connect the terminal of the aluminum alloy tube to the port which is on side of the main body (see picture 1). 4 Pic Put the aluminum alloy tube into the product body. Rotate the aluminum alloy tube until it gets locked (see picture 2). 3. Install battery ( No need for new product) 3.1. Remove the screws and open the cover ( see picture 1) Pic Connect the terminals correctly ( see picture 2) 3.3. Recharge the battery monthly to keep good battery performance. Non-original battery may damage the product.

5 OPERATING INSTRUCTIONS 1. Add water/waxing oil/detergents 1.1. Push the PUSH button to open the plastic cover (See picture 1) 1.2. Remove the rubber plug and fill the water tank with water or waxing oil or diluted detergent in appropriate amount. (see picture 2) 1.3. If necessary, clean surplus quantities with an absorbent cloth and close the cover. *Always keep some water or other suitable liquid in the water tank to avoid water pump idling. Pic 2 2. Charging 2.1. Fully charge the battery before first use 2.2. Always use the original charger to charge the battery 2.3. A slow flashing LED (about one flashing every second) indicates low battery. Please charge the battery in time. 3. Replace PADS 3.1. Use the original cleaning or waxing pads 3.2. Put the adhesive side of the pad on the rotary plate (see picture 1) 3.3. Power off and hold the edge of the pad and then slightly pull off the pad USING 4.1. Fix pads on the rotary plates Fill in Scheucher PARQUET CARE (for maintaining your oiled/waxed parquet floor) OR Scheucher PARQUET CLEANER (diluted with water as indicated) (for cleaning your parquet floor) into the tank Choose the speed of rotation by moving the selector switch. Low speed is intended for cleaning your parquet floor, high speed is for polishing of the care wax oil Move slowly forwards and backwards and spray care wax oil or detergent on the parquet floor as required. Observe the spray distance to avoid contamination of walls or furniture Clean floor before you apply PARQUET CARE Only use clean pads for PARQUET CARE Please empty the tank, if you do not want to use your for an extended period of time, fill in water, clean the nozzle with a few sprays and then empty the water.

6 TROUBLE SHOOTING PROBLEM CAUSES SOLUTION Water spray failure Tank is empty There is air in the water pipe Fill tank Push spray button several times to expel the air Nozzle blocking Motor stops workink and LED flashes rapidly LED flashes once every second Motor stops, LED lights properly Spray nozzle/water injector blocked Hard components are contained in the liquid. Over-current protection Low battery Motors over-temperature protection Clean nozzle opening with a needle Leeren Sie den Tank und füllen Sie den Tank neu auf. Restart after a few seconds. Recharge battery Stop using and turn off the switch. Cool it naturalls and reuse it. 6 Please note: 1. Temperature increases in the long continuous uninterrupted running process of the motor. Over-temperature protection starts upon over-heated motors. Turn off the switch, cool the product naturally and reuse 2. Don t keep it working for more than 20 minutes for one time 3. Do not apply any force load on the machine FAQ: How to clean the pad? Clean pads after cleaning your floor with clear water. In case of heavy contamination, wash the pads in the washing machine at max. 60 C. After using care wax oil, immediately wash the pads in the washer at a maximum of 60 C. This prevents the risk of self-ignition and you can reuse the pads. Where can I buy pads, battery, care and maintenance products? Please contact your local Scheucher dealer. Will it damage the floor when the rotary plates rotate at high speed? Fitted with soft and thick-anti-abrade pads, the rotary plates make no damage to the floor. Can it clean dirt or dust? Our special pads can absorb dirt, dust or liquid amounting to several times pad s weight. How do I correctly clean my parquet floor with? First, clean the floor with a vacuum cleaner to remove coarse dirt. Fill PARQUET CLEANER in the tank and clean the parquet floor by slowly moving back and forth. Spray the cleaner as needed on the floor. Work in partial surfaces. Due to the high absorption capacity of the pads, a too wet cleaning is automatically avoided. Follow the instructions of Scheucher PARKETT CLEANER.

7 How do I correctly use PARQUET CARE my parquet floor with? Clean the floor as described before. Empty the tank and fill in PARKETT CARE care oil into the tank. Replace the pads and use the green care pads. Spray PARQUET CARE on the floor and polish it at high speed by slowly moving the back and forth. Work in partial areas and spray it onto the floor as needed. Avoid a visible, wet oil film on the parquet floor. ATTENTION: Over waxed floors may become slippery and cause danger. Follow the instructions of PARQUET CARE. How do I correctly charge my? When the battery becomes empty, the rotational speed of the rotary plates drops and the motor stops. Use only the original charger to recharge the battery. During charging, the LED lights up red as soon as charging is completed, the LED lights up green. How long does it take to charge the battery? A complete charge takes 2.5 to 3 hours. If the machine does not work out as intended, please read the operating instructions first. If you can t find a solution, please contact your dealer or contact us at CONTENT Nr. NAME AMOUNT BEMERKUNG 1 waxer and cleaner Charger Europe 230 V 1 3 Waxing pads (green) 2 use for care with Scheucher Parquet CARE 4 Cleaning pads (blue) 2 use for cleaning with Scheucher Parkett CLEANER 5 Manual 1 in German and English language Designed for Scheucher in USA, Made in China. Mamibot Manufacturing USA Inc. Orange St. #600, Wilmington, New Castle, Delaware, USA.

8