ECLIPSE CCFL ANGEL EYES FITTING GUIDE COURTESY OF CHROMELINE DESIGN

Size: px

Start display at page:

Download "ECLIPSE CCFL ANGEL EYES FITTING GUIDE COURTESY OF CHROMELINE DESIGN"

Doreen Beasley
5 years ago
Views:

1 ECLIPSE CCFL ANGEL EYES FITTING GUIDE COURTESY OF CHROMELINE DESIGN Page 1 of 8

2 : Thank you for purchasing Eclipse Lights for your BMW E36. Please read through these instructions carefully before installation. CAUTION Eclipse lights are made from GLASS, please be careful when handling the rings to avoid any breakages or personal injury. DO NOT put any force on the rings at any time during installation When correctly installed the rings will provide years of trouble free operation. The kit is very easy to install. Please take your time during the installation. The rings, once installed, are durable enough to take the rigors of driving. When installed the rings will resist vibration extremely well. The rings are only susceptible to breakage during installation if not careful. Do not attempt to flex, bend or put pressure on the ring itself. The rings can shatter when broken which may result in flying glass. It is advisable to wear eye protection when handling & installation the rings. All fluorescent lamps contain small amounts of Mercury. If you break a ring do not blow the debris away or inhale the powder. Wipe up any debris with a damp paper towel. Handle the rings with care until they are installed inside of headlights and they will provide years of trouble free operation. Lamps can last for over 100,000 hours of operation. The power packs included have to be hard wired into the headlamps. Ensure you have suitable connectors or soldering equipment available before installation. Please contact us if you have questions before continuing Eclipse Lights are guaranteed for 1 year. Return any defective components for immediate replacement. (Rings which have been broken during installation are not covered) Enjoy your product The Eclipse Team Page 2 of 8

With the headlamps removed from the vehicle :.

and back housing together. 2 clips are on the top and 2 clips on the bottom.

There are 4 clips to release, 2 on each side of the headlamp.

Ensure that the headlamp lenses are clean and free of any dirt/dust.

3 With the headlamps removed from the vehicle :. 1, Use a flat blade screwdriver, remove the 4 metal clips holding the lens assembly and back housing together. 2 clips are on the top and 2 clips on the bottom. 2, Unclip the lens assembly from the rear housing. There are 4 clips to release, 2 on each side of the headlamp. 3, Pull the lens assembly apart from the rear housing and place on a clean surface. Ensure that the headlamp lenses are clean and free of any dirt/dust. Clean them it if necessary!!! CAUTION!! Be very careful when handling the rings they are made of GLASS. Do not exert any force on the ring at any time 4, Carefully slide a tube shaped moulding onto each ring. Page 3 of 8

5, Carefully place the ring into the lens cavity.

* * It may be necessary to bend the wiring on the end of the ring, If

6, Ensure the tube moulding is positioned with the flat surface facing

Carefully rotate the tube into the desired position, if required.

4 5, Carefully place the ring into the lens cavity. Ensure the ring is seated flat against the lens. * * It may be necessary to bend the wiring on the end of the ring, If necessary please do so very carefully. 6, Ensure the tube moulding is positioned with the flat surface facing away from the lens, i.e. towards you. Carefully rotate the tube into the desired position, if required. 7, Use masking tape to hold the rings in position as shown. 8, The next step requires a clear Silicone based sealant/adhesive. Clear sealant/adhesives are readily available from motor factor stores. Page 4 of 8

Edge of glass lens 9, Carefully apply the silicone adhesive onto the ends of the rings as

Remove any unwanted adhesive immediately (follow the instructions on the silicone sealant)

moulding and the edge of the lens as shown.

5 Edge of glass lens 9, Carefully apply the silicone adhesive onto the ends of the rings as shown. Only apply adhesive to the edge of the glass lens. Remove any unwanted adhesive immediately (follow the instructions on the silicone sealant) Edge of glass lens 10, Carefully apply the silicone adhesive onto the flat edge of the tube moulding and the edge of the lens as shown. Repeat steps 5-10 until all of the rings have been assembled in position. Allow the silicone adhesive to cure. The power packs can be installed whilst the silicone is curing. Page 5 of 8

11, Remove the back cover from the headlamp and remove the side light bulb holder.

The power packs are terminated with bullet connectors which can be removed if not required.

Join the RED wire (positive) from the power pack to the GREY wire (positive) from the headlamp side light circuit.

6 11, Remove the back cover from the headlamp and remove the side light bulb holder. 12, Wiring the power pack into the side light circuit. The power packs are terminated with bullet connectors which can be removed if not required. Soldering is the best method to join the wires although Scotch Loc type connectors can be used. Join the RED wire (positive) from the power pack to the GREY wire (positive) from the headlamp side light circuit. Join the BROWN wire (earth) from the power pack to the BROWN wire (earth) from the headlamp side light circuit. Check that all connections are secure. 13, Carefully bring the lens You may want to remove the standard side assembly light bulb and before back housing continuing. together. Ensure the silicone holding the rings is cured before continuing Carefully pass the wires from the rings through the top of the reflectors in the back housing. DO NOT PULL ON THE WIRES as they may damage the rings. Page 6 of 8

14, Carefully assemble the lens assembly and back housing together.

The 4 clips should click when correctly assembled.

16, Assemble the wires from each ring into the black connectors.

Push the metal clip into the black plastic connector as shown.

7 14, Carefully assemble the lens assembly and back housing together. Make sure the wiring is not trapped when reassembling. The 4 clips should click when correctly assembled. 15, Carefully pass the wiring from the rings through the back housing as shown. 16, Assemble the wires from each ring into the black connectors. Ensure that the small tang on the metal clip is facing upwards. Push the metal clip into the black plastic connector as shown. The metal clips will lock into position when correctly assembled. Each ring should be wired into its own connector. 17,Assemble the connectors together as shown. The rings can be connected to either plug from the power pack. Page 7 of 8

18, Remove the self adhesive backing paper from the power pack and secure

Tidy the wiring using the cable ties provided.

8 18, Remove the self adhesive backing paper from the power pack and secure to the inside of the headlamp. Tidy the wiring using the cable ties provided. 19, Refit the back cover and the 4 metal clips to each headlamp. Refit the headlamps to the vehicle. Eclipse Lights may take up to 60 seconds to reach full brightness, this is perfectly normal. Please contact us if you have any questions before installation. Enjoy your Eclipse Lights Page 8 of 8

Bulb Replacement REPLACING BULBS

Bulb Replacement REPLACING BULBS Check the operation of all exterior lamps before you drive the vehicle. Caution: Before attempting to replace a bulb, ensure that both the affected lamp and the vehicle's