MOTORCYCLE DIVISION 4-STROKE BULLETIN NO. GS/GSX/GSX-R - 97 REVISED DATE: 9/2/98
|
|
- Noreen Armstrong
- 5 years ago
- Views:
Transcription
1 MOTORCYCLE DIVISION 4-STROKE BULLETIN NO. GS/GSX/GSX-R - 97 REVISED DATE: 9/2/98 MODEL: SUBJECT: REFERENCE: GSX-R750W FUEL HOSE DISCONNECTED FROM FUEL PUMP NEW FUEL PIPE SET (PN E50) SERVICE MANUAL (PN E) & SERVICE MANUAL SUPPLEMENT ( E) This bulletin contains revised parts and repair information. Follow the recommendations and instructions in this bulletin when installing the new fuel pipe set, fuel pump gasket and mounting bolts. Discard the original GSX-R #97 bulletin dated 8/14/98 and place this version in your service bulletin set. NOTICE: In certain regions of the country, the hose connecting the fuel pump to the fuel filter may come off causing a lack of fuel pressure to the fuel injection system. The fuel pump will operate normally when the ignition is turned on, but the engine will not start because fuel is not pumped into the fuel injection system. If you encounter this symptom, inspect the fuel pump output. If faulty, remove the fuel pump assembly from the fuel tank and see if the fuel hose has come off the fuel pump or fuel filter. If so, replace the hose and original clamps with a Fuel Pipe Set (PN E50). The fuel pipe set has a pair of hoses, new hose clamps, and a pipe/ bracket combination which will secure the fuel pipe and hoses to the fuel pump bracket with screws. Use a new Fuel Pump Gasket (PN F01) and new Fuel Pump Mounting Bolts (PN F00, Qty. 8) when reinstalling a repaired fuel pump into the fuel tank. The new fuel pump mounting bolts have a different torque specification than the original bolts (see page 4 of this bulletin). AFFECTED MODELS: Some 1998 GSX-R750W models may be affected. No action is required unless the motorcycle will not start due to a lack of fuel pump output
2 hose ORIGINAL FUEL HOSE PN E50 is secured to pump bracket with screws NEW FUEL PIPE SET PN E50 and bracket assembly PARTS INFORMATION: Order the parts listed below from the Suzuki Parts Department as needed. Part Description Part Number Qty. Fuel Pipe Set E50 1 Fuel Pump Gasket F01 1 Mounting Bolts F00 8 CORRECTIVE ACTION: Carefully read and follow the instructions, warnings and cautions in section 4 of the GSX-R750 Service Manual Supplement (PN E) before beginning service. Verify fuel pump operation by performing the fuel pressure inspection outlined on page 4-50 and the fuel discharge amount inspection on page Fuel pressure gauge adaptor Oil pressure gauge Oil pressure gauge hose FUEL PRESSURE: FUEL DISCHARGE AMOUNT: 41 psi (2.9kg/cm 2, 250kPa) 1.1 oz/3 seconds (26-30ml/3 seconds) Gasoline is highly flammable, explosive and toxic. Keep heat, sparks and flame away. If the fuel pump does not meet the fuel pressure and discharge specifications, the fuel pump assembly will need to be removed and inspected
3 INSTALLING THE FUEL PIPE SET: Remove the fuel tank (see page 4-49) Remove the fuel pump assembly from the fuel tank by removing the mounting bolts (see page 4-51). 1 hose ORIGINAL Fuel Pump (Fig 1) If the fuel pump hose has come off the fuel pump or filter, remove it completely from the fuel pump assembly and replace it with the fuel pipe set. Fuel pump CAUTION Do not reuse a fuel pump hose that has come off the pump or filter fitting. Replace the hose with a new fuel pipe set. Do not reuse the original hose clamps. Only use the new clamps from the fuel pipe set. & bracket (Fig 2) Slip the hoses onto the fuel pump and fuel filter fittings. Secure the pipe/bracket to the fuel pump assembly bracket with the new screws provided with the pipe set. CAUTION The fuel pump fitting, fuel filter fitting and new fuel pipe and hoses must be free of gasoline or other residue or the hoses may not stay secured on the pump assembly. NEW Fuel Pipe Set 2 Fuel Pipe Set Mounting & bracket Screw The new pipe and hoses need to be thoroughly cleaned with contact cleaner, or a similar solvent, to remove any "release agent". The "release agent", is a film left on the hose from the molding process.
4 (Fig 3) The new fuel pump mounting bolts are a flange-head style. The original bolts have a hex head with a lock washer. 3 Fuel Pump Mounting Bolts The fuel pump gasket and mounting bolts must be replaced with a new a fuel pump gasket and new style mounting bolts to prevent fuel leakage. Clean the fuel pump mounting flange on the fuel tank. Install the new fuel pump gasket on the fuel tank before reinstalling the fuel pump. ORIGINAL Hex Head NEW Flange Head NOTE: Make sure the mounting bolt holes in the fuel tank and gasket align before attempting to install the fuel pump. 4 Mounting Bolt Tightening Sequence Gently slide the fuel pump into the fuel tank. Take care to not disturb the fuel pump gasket. Turn the new fuel pump mounting bolts lightly in by hand until they are seated (Fig. 4 & 5) Perform the mounting bolt tightening sequence in three steps: Torque the mounting bolts to the initial torque (1.8 lb-ft) following the correct sequence. " Torque the bolts to final torque (2.9 lb-ft) following the correct sequence. #Torque the bolts once again to the final torque (2.9 lb-ft) in the correct sequence. 7 2 FRONT Failure to follow the fuel pump mounting bolt torque specifications and tightening sequence could cause improper gasket sealing and fuel leakage. 5 Mounting Bolt Torque Steps & Specifications DO NOT OVER TIGHTEN THE MOUNTING BOLTS. Reinstall the fuel tank, following the instructions on pages 4-49 and 4-50 of the GSX- R750W service manual supplement (PN E). Clean and polish any fingerprints from the motorcycle. Add fuel so the fuel amount is at least the amount the customer had in the motorcycle before the fuel hose repair. (1) Initial torque...1.8lb-ft (21.6lb-in, 2.5N.m, 0.25kgf.m) (2 & 3) Final torque...2.9lb-ft (34.8lb-in, 4.0N.m, 0.4kgf.m) NOTE: A 1/4" drive torque wrench, calibrated in lb-in, works well on the low-torque mounting bolts
5 RIDE THE MOTORCYCLE: To ensure customer satisfaction, Suzuki suggests you ride the motorcycle several miles to make sure there are no fuel leaks and all the controls and the motorcycle operate correctly. ADVISE THE CUSTOMER OF THE FUEL LEVEL WHEN YOU DELIVER THE MOTORCYCLE. Correct any fuel pipe set repair related problems before delivering the motorcycle to the customer. AFFECTED DEPARTMENTS: The following departments in your dealership should be notified of this information: *Service * Parts *Sales Accessories American Suzuki Motor Corporation Technical Service Department Motorcycle - 5 -
CAUTION Fuel Lift Pump. Initial Check. Resistance Check. https://qsol2.cummins.com/qs2/pubsys2/xml/en/procedures/10/
Page 1 of 16 View Related Topic 005-045 Fuel Lift Pump Initial Check Inspect the engine harness, the lift pump power connector, the lift pump relay power connector and the lift pump relay pins for the
More informationB-026INT October 6, 1999 FUEL FILTER BRACKET RETROFIT (JAPAN ONLY) GENERAL RETURN THIS TO: INITIAL HERE TECHNICIAN NO.
5 SERVICE BULLETIN B-026INT October 6, 1999 FUEL FILTER BRACKET RETROFIT (JAPAN ONLY) GENERAL It has come to the attention of Buell Distribution Corporation that a certain number of 2000 Model X1 and S3/T
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. MII 11775 AUDIO ATTACHMENT KIT P/N 08B08-MEA-100 VTX1300S/R Issue Date October 2006 Honda Dealer: Please give a copy of these instructions
More information5-2 FUEL SYSTEM AND THROTTLE BODY FUEL SYSTEM FUEL DELIVERY SYSTEM The fuel delivery system consists of the fuel tank, fuel pump, fuel filters, fuel f
FUEL SYSTEM AND THROTTLE BODY 5-1 FUEL SYSTEM AND THROTTLE BODY I CONTENTS FUEL SYSTEM 5-2 FUEL DELIVERY SYSTEM 5-2 FUEL PUMP 5-3 FUEL PRESSURE REGULATOR 5-4 FUEL INJECTOR 5-4 FUEL PUMP CONTROL SYSTEM
More informationAutomotive FORENZA / RENO October 6, 2014 Technical Service Bulletin Engine Bulletin No. TS R1
Service Automotive FORENZA / RENO October 6, 2014 SUBJECT: MODEL(S): YEAR: Revisions: Throttle Position Sensor Replacement Forenza (RQ420) Reno (RQ420) 2006 2008 Forenza 2006 2008 Reno R1-10/08/14. This
More informationEquipped with Engine RPOs listed in the Table Below and MULTEC 2 Fuel Injectors
Various Driveability Symptoms Due to Clogged Fuel Injectors, MIL/SES DTCs P0171, P0172, P0174, P0300, P1174, P1175 (Clean Fuel Injectors and/or Perform Injector Test With AFIT CH-47976) 2005-2013 GM Passenger
More informationChevrolet Avalanche, Silverado 1500, Suburban, Tahoe
Engine Oil Consumption on Aluminum Block/Iron Block Engines with Active Fuel Management (AFM) (Install AFM Oil Deflector and Clean Carbon from Cylinder) 2007-2010 Cadillac Escalade, Escalade ESV, Escalade
More informationof 9 2/3/204 :44 PM 2007 GMC Yukon 5.3L Eng Base ENGINE OIL CONSUMPTION ON ALUMINUM BLOCK/IRON BLOCK ENGINES WITH ACTIVE FUEL MANAGEMENT (AFM) (INSTALL AFM OIL DEFLECTOR AND CLEAN CARBON FROM CYLINDER
More informationINSTALLATION TRUE DUAL HEADPIPES 497
TRUE DUAL HEADPIPES 497 PARTS INCLUDED 1 Front Head Pipe 1 Rear Head Pipe 1 Front Heat Shield 1 Rear Heat Shield 1 Bracket (stamped 422-P) 1 Bracket (stamped 423-P) 2 1/2 x 1-1/4 Socket Head Cap Screw
More information2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions P/N: (99-137)
2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions P/N: 422046 (99-137) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions
More informationUTV Universal Stronghold Auto- Latch Double Boot Mount
UTV Universal Stronghold Auto- Latch Double Boot Mount Product Instructions Part No: 0000 3 3 This Kit includes: Item Qty Part Description Bracket, Stronghold Adjustment Bracket, Bed Side Mount 3 Tube,
More information5. FUEL SYSTEM 5-0 FUEL SYSTEM UXV 500
5 FUEL SYSTEM 5 SERVICE INFORMATION------------------------------------------------ 5-02 TROUBLESHOOTING----------------------------------------------------- 5-03 FUEL TANK -----------------------------------------------------------------
More informationModel 797/797A/797B Tune-Up Kit
Model 797/797A/797B Tune-Up Kit Jacobs P/N 032146 This Tune-Up Kit requires Master Piston Assembly Tool, P/N J-45976. The tool is available through Kent-Moore. Information in this manual was current at
More informationLong Tube Header Installation PNs , 17276
Long Tube Header Installation PNs - 17260, 17276 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary for this installation.
More informationTECHNICAL BULLETIN. Yoke Removal and Installation Procedure for Meritor Drive Axles. Remove the Yoke and Pinion Seal WARNING CAUTION CAUTION.
Issued 11-99 TECHNICAL BULLETIN Yoke Removal and Installation Procedure for Meritor Drive Axles Remove the Yoke and Pinion Seal Figure 1 WARNING Park the vehicle on a level surface. Block the wheels to
More informationAIR CLEANER GENERAL REMOVAL. 1CAUTION Do not run engine without filter element in place. Debris could be drawn into the engine causing damage.
AIR CLEANER GENERAL The air cleaner prevents foreign material from entering the carburetor and engine by trapping airborne dust and dirt in the filter element. Service air cleaner filter element every
More informationNOTE: This bulletin applies to CS models built after February 1, 2004 (MDH 0201XX) equipped with a 3.5L engine (Sales Code EGN).
NUMBER: 09-010-06 GROUP: Engine DATE: September 16, 2006 THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 09-005-05, DATED DECEMBER 2, 2005, WHICH SHOULD BE REMOVED FROM YOUR FILES. THIS IS A COMPLETE
More information2015+ Mustang GT V8 X-Pipe/H-Pipe Exhaust Kit Installation Instructions
2015+ Mustang GT V8 X-Pipe/H-Pipe Exhaust Kit Installation Instructions P/N: 422046 and 422119 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang GT V8 X-Pipe/H-Pipe Exhaust Kit Installation
More informationSymptom Diagnostics - Hard Start/No Start April Hard Start/No Start - Two-Filter Fuel System (This Test Must Be Done First)
04 10-17 1 04 10-17 SUBJECT DATE Symptom Diagnostics - Hard Start/No Start April 2017 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Hard Start/No Start - Two-Filter
More informationP0171, P0172, P0174, P0300, P1174, P1175
#03-06-04-030F: Various Driveability Symptoms Due to Clogged Fuel Injectors, MIL/SES DTCs P0171, P0172, P0174, P0300, P1174, P1175 (Clean Fuel Injectors and/or Perform Injector Test With AFIT - CH-47976)
More information2015+ Mustang Shift Ball Installation Instructions P/N: (R BLK) P/N: (R WHT)
2015+ Mustang Shift Ball Installation Instructions P/N: 421906 (R1315-7213 BLK) P/N: 421907 (R1315-7213 WHT) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang Shift Ball Installation
More informationSERVICE INSTRUCTIONS. Material Pump
TM TM SERVICE INSTRUCTIONS Material Pump 9618 DESCRIPTION Model 9618 is designed for pumping petroleum products from the original container to a desired location. Due to its non-corrosive (aluminum and
More information5. FUEL SYSTEM 5-0 FUEL SYSTEM MXU 250R/300R
5 FUEL SYSTEM 5 SERVICE INFORMATION------------------------------------------------ 5-2 TROUBLESHOOTING----------------------------------------------------- 5-3 FUEL TANK -----------------------------------------------------------------
More informationINSTRUCTION FOR EFI FUEL PRESSURE GAUGE TOOL
INSTRUCTION FOR EFI FUEL PRESSURE GAUGE TOOL This gauge is now a must have new tool, as 90% of all Big Twins motorcycles have Electronic Fuel injection. (EFI). If you have a customer that is experiencing
More information2011 Cadillac SRX SRX VIN N Service Manual #PI0703B: Service Rear Axle Message Displayed on Driver Information Center (DIC), DTC C0407 with Symptom Code 64 or C0403 Symptom Code 62 Set - (Feb 25, 2013)
More informationHeader Installation for Ford Mustang GT, PN-17290* Adaptor Pipe PN-60566**
Header Installation for Ford Mustang GT, PN-17290* Adaptor Pipe PN-60566** These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this
More informationSUBJECT: INTEGRATED FUEL SYSTEM (IFS) UNIT PUMP SERVICE
DATE: July 30, 2010 SERVICE BULLETIN SUPERSEDES: S.B. 560 dated November 22, 2008 NO: 560R1 SUBJECT: INTEGRATED FUEL SYSTEM (IFS) UNIT PUMP SERVICE RELATED PUBLICATIONS: IFS OPERATION AND INSTRUCTION MANUAL
More informationFord F-150 Off Road Exhaust Kit
2011-14 Ford F-150 Off Road Exhaust Kit P/N: 620092 (SLP1111-5E292) Application: 2011-14 Ford F-150 equipped with the following engine options: 3.5L Eco-Boost Engine with automatic transmission. 5.0L 4V
More informationw w w. h d o n l i n e s h o p. d e SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL INSTALLATION -J04480 REV.
-J080 REV. 2009-05-2 SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL Kit Numbers 292-08, 29080-09 Models For model fitment information, see the P&A Retail Catalog or the Parts and
More informationVOYAGEUR 144 BRAKE LIGHT SUPPORT KIT
VOYAGEUR 144 BRAKE LIGHT SUPPORT KIT P/N 2883838 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationPage 1 of 6 Section 03-01C: Engine 3.4L SHO 1999 Taurus/Sable Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/25/1998 Intake Manifold Upper Removal 1. Disconnect battery ground cable (14301).
More informationInjector. General Information CAUTION. Use only the specified injector for the engine.
Page 1 of 32 006-026 Injector General Information CAUTION Use only the specified injector for the engine. All engines use closed nozzle, hole-type injectors. However, the injectors can have different part
More information2014+ GM Truck Cat Back Exhaust Kit 4.3L/5.3L/6.2L
2014+ GM Truck Cat Back Exhaust Kit 4.3L/5.3L/6.2L Installation Instructions P/N: 620074 (99-47) 4.3L/5.3L P/N: 620080 (99-139) 6.2L 39555 Schoolcraft Rd, Plymouth MI, 48170 855.SLP.PERF 2014+ GM Truck
More informationInstallation Instructions And Warranty Information
Corporate Office: PerTronix Inc. 440 E. Arrow Highway, San Dimas, California 91773 * Phone 909.599.5955 FAX 909.599.6424 Installation Instructions And Warranty Information 1999-2006 Chevrolet/GMC 2WD 1500,
More informationOperating and Maintenance Manual Gas & Diesel Engine Powered Diaphragm Pumps. Series 55A
Operating and Maintenance Manual Gas & Diesel Engine Powered Diaphragm Pumps Series 55A Operation Manual Contents: Serial Number/Model Number Information Pg.1 Safety Information Pg. 1 Safety Information
More informationIGNITION TIMING (GASOLINE)
IGNITION TIMING (GASOLINE) 4-CYLINDER IGNITION TIMING 2.5L (VIN E) 1. Set parking brake, block drive wheels and place transmission in Neutral or Park. Warm engine to normal operating temperature. Turn
More informationInstallation for Honda Accord PN s 11840, 11853, 11949
Installation for Honda Accord PN s 11840, 11853, 11949 BORLA PERFORMANCE INDUSTRIES ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts
More informationThis Bulletin has been revised to update Warranty Information. Please discard Corporate Bulletin Number L.
2008 C hevrolet Avalanche - 2WD [3GNEC 12048G177472] Avalanche, Escalade, Suburban, Tahoe, Yukon VIN C /K Service Manual Engine Engine Mechanical - 4.8L, 5.3L, 6.0L, 6.2L, or 7.0L Repair Instructions -
More informationInstallation Instructions Part Number
Installation Instructions Part Number 84152143 Thank you for choosing Chevrolet Performance as your high performance source. Chevrolet is committed to providing proven, innovative performance technology
More informationSB Service Bulletin
SB-10052924-4799 Service Bulletin Applies To: 2013 Pilot 2WD From VIN 5FNYF3...DB014058 thru 5FNYF3...DB025447 2013 Pilot 4WD From VIN 5FNYF4...DB025128 thru 5FNYF4...DB048530 13-055 July 19, 2013 MIL
More informationPerformer Series Carburetor Rebuild Kit Catalog #1477 Models
Please read these instructions carefully before attempting to rebuild your carburetor. Make sure to refer to your carburetor Owner s Manual for further information if need be. If you have any questions
More informationSERVICE INSTRUCTIONS Air Motor
SERVICE INSTRUCTIONS Air Motor 338905 DESCRIPTION The air motor has a 3" diameter piston with a -5/8" stroke. When the pump-tube upper packing is not incorporated into the air motor, the air motor is considered
More informationROUSH Convertible Stylebar Installation Instructions P/N: (1315-STYLEBAR) Convertible Only
Installation Instructions P/N: 421911 (1315-STYLEBAR) Convertible Only 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH Installation Instructions P/N: 421911 (1315-STYLEBAR) Convertible Only Application:
More informationM-SERIES DIAPHRAGM COMPRESSOR REBUILD KIT
Copy Part# 20000, Rev. E Page 1 of 9 M-SERIES DIAPHRAGM COMPRESSOR REBUILD KIT Part# 20090K Disassembly Instructions DO NOT discard any component unless directed to do so. All mounting hardware will be
More informationIMPORTANT INFORMATION
Table of Contents IMPORTANT INFORMATION Section 1B - Maintenance MAINTENANCE 1 B Specifications........................... 1B-1 Special Tools........................... 1B-2 Mercury/Quicksilver Lubricants
More information5. FUEL SYSTEM FUEL SYSTEM 5-0
5 FUEL SYSTEM 5-0 SERVICE INFORMATION GENERAL INSTRUCTIONS SERVICE INFORMATION...5-1 CARBURETOR INSTALLATION...5-9 TROUBLESHOOTING...5-1 PILOT SCREW ADJUSTMENT...5-10 CARBURETOR REMOVAL...5-2 AUTO BYSTARTER...5-3
More informationRepair Instructions and Parts List
Repair Instructions and Parts List 309887B Manufactured by Pressure Washers INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. APS2730H Model 246798, Series
More information2015+ Mustang LoudMouth I and LoudMouth II Exhaust Kits
2015+ Mustang LoudMouth I and Installation Instructions P/N: 620054, 620055, 620061, 620062 (S1315-5231LM1, S1315-5231LM2, S1315S1-5231LM1, S1315S1-5231LM2) *LoudMouth II shown. BY 39555 Schoolcraft Rd,
More informationMaintenance Manual WATER SUMP CONTROL VALVE F532B
WATER SUMP CONTROL VALVE F532B LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical line in the outer margin of the page. When
More information4. FUEL SYSTEM 4-0 FUEL SYSTEM NEXXON 50
4 FUEL SYSTEM SERVICE INFORMATION ------------------------------------------------ 4-2 TROUBLESHOOTING----------------------------------------------------- 4-3 AIR CLEANER REMOVAL -----------------------------------------------
More informationB-022 June 11, 1999 SAFETY RECALL CODE FUEL TANK VENT VALVE ASSEMBLY GENERAL RETURN THIS TO: INITIAL HERE TECHNICIAN NO.
4 SERVICE BULLETIN B-022 June 11, 1999 SAFETY RECALL CDE 0815 - FUEL TANK VENT VALVE ASSEMBLY GENERAL Buell Motorcycle Company has learned that certain 1995 through 1999 Buell motorcycles were built with
More informationSERVICE INSTRUCTIONS. Transfer Pump
TM TM SERVICE INSTRUCTIONS Transfer Pump 6799 DESCRIPTION Model 6799 is an air operated, self-priming, piston type transfer pump designed to transfer gasoline or diesel fuel at 30 gpm or oils up to SAE
More information12. CARBURETOR 12-0 CARBURETOR VITALITY 50
12 12 CARBURETOR SERVICE INFORMATION (2-STROKE)... 12-2 SERVICE INFORMATION (4-STROKE)... 12-3 THROTTLE VALVE (2-STROKE)... 12-5 CARBURETOR (2-STROKE)... 12-7 AIR SCREW ADJUSTMENT (2-STROKE)... 12-13 REED
More informationAG-HA-2500N GASOLINE GENERATOR
AG-HA-2500N GASOLINE GENERATOR OWNER S MANUAL BEFORE OPERATING THIS EQUIPMENT PLEASE READ THESE INSTRUCTIONS CAREFULLY (I)WARNING 1. Read the operator s instruction manual. 2. Attention! Exhaust gases
More information18SP653 EPA04 and EPA98 MBE 4000 High Pressure Fuel Line and Transfer Tube Installation
18SP653 EPA04 and EPA98 MBE 4000 High Pressure Fuel Line and Transfer Tube Installation KIT DESCRIPTION A service kit (P/N: A4600700135) is now available to install EPA07 high pressure fuel injector lines
More informationTHIS PRODUCT IS DESIGNED FOR USE IN CLOSED COURSE RACING AND IS NOT INTENDED FOR HIGHWAY USE.
RESEARCH&DEVELOPMENT OF AMERICA, INC. 420 DANIELS STREET STE A, CHINO CA., 91710 (800)634-9166 (909)628-4722 FACSIMILE (909)91-2198 www.yoshimura-rd.com YOSHIMURA PERFORMANCE EXHAUST SYSTEM 2006-2007 SUZUKI
More informationInstallation Instructions and Warranty Information
Corporate Office: PerTronix Inc. 440 E. Arrow Highway, San Dimas, California 91773 * Phone 909.599.5955 FAX 909.599.6424 Installation Instructions and Warranty Information JBA Headers for JEEP Wrangler
More informationFuel Pump ( ) Table of Contents. Summary. View Related Topic. Summary. General Information Test. Preparatory Steps. Remove.
View Related Topic Fuel Pump (005-016) Table of Contents Summary General Information Test Without Electric Lift Pump With Electric Lift Pump Preparatory Steps Marine Applications Remove Rear Gear Train
More informationTECHNICAL SERVICE BULLETIN
Bulletin No.: TSB-023 Date: June 2, 2016 Subject: Models: EMER NGV1 Fill Receptacles Gen 2 Back Of Cab, Gen 3 Frame Mount Fuel Storage Modules Background All Quantum fuel storage modules are equipped with
More informationCRUSHER TRUE DUAL HEADPIPES 513
CRUSHER TRUE DUAL HEADPIPES 513 THANK YOU FOR CHOOSING CRUSHER! PROTECT YOURSELF AND OTHERS FROM POTENTIAL INJURY AND PROPERTY DAMAGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS,
More informationActions Required to Avoid Repeat Turbocharger Failures
SERVICE BULLETIN (Also applies to Mack Trucks Australia) (Supersedes SB214020 dated 7/26/04) Number: SB214020 Date: 07/21/05 Model: ASET, E-Tech Actions Required to Avoid Repeat Turbocharger Failures When
More information2014 Buick Encore. Fig. 2: Replacing Measured Compressor Oil Courtesy of GENERAL MOTORS COMPANY
Fig. 2: Replacing Measured Compressor Oil Courtesy of GENERAL MOTORS COMPANY 2. Add back the same quantity of polyalkylene glycol (PAG) oil as drained from the removed air conditioning compressor. Refer
More informationCylinder head, removing and
Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder
More informationM-9603-SVT mm Cold Air Kit w/premium Calibration INSTALLATION INSTRUCTIONS
Please contact the Tech Line for the most current instruction information (800) 367-3788.!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: This kit is designed for
More informationMustang Billet Rear Lower Control Arm Kit
Mustang Billet Rear Lower Control Arm Kit Part #R06030037 Application: 2005-2009 Ford Mustang Installation Instructions Before installing your ROUSH Performance Product(s), read through the entire installation
More informationEDELBROCK THUNDER SERIES AVS CARBURETORS Part #1801, 1802, 1803, 1804, 1805, 1806, 1812, 1813, 1825, 1826 INSTALLATION INSTRUCTIONS
EDELBROCK THUNDER SERIES AVS CARBURETORS Part #1801, 1802, 1803, 1804, 1805, 1806, 1812, 1813, 1825, 1826 INSTALLATION INSTRUCTIONS IMPORTANT NOTE: Proper installation is the responsibility of the installer.
More informationINTAKE AIR TEMPERATURE SENSOR (IAT)
INTAKE AIR TEMPERATURE SENSOR (IAT) 4.8 Refer to the ELECTRICAL DIAGNOSTIC MANUAL for information on the function and testing of the intake air temperature sensor (IAT sensor). sm054 To prevent accidental
More informationNote: The engine may start, but you may still have high leakoff within the high-pressure fuel system. NOTICE
Introduction There have been isolated occurrences of excessive fuel leakage past the electronic unit injectors on some engines. Accelerated wear on the delivery valve results in an increased leak rate.
More information1 of 12 12/28/2015 8:40 PM
1 of 12 12/28/2015 8:40 PM TECHNICAL Bulletin No.: 11-06-04-007C Date: November 08, 2012 Subject: Diagnosis and Repair - Malfunction Indicator Lamp (MIL) Illuminated, Reduced Engine Power Message Displayed,
More informationFitting Instructions: Street Triple Arrow Race Exhaust System 3:1 - A
Fitting Instructions: Street Triple Arrow Race Exhaust System 3: - A960098 Thank you for choosing this Triumph genuine accessory kit. This accessory kit is the product of Triumph's use of proven engineering,
More informationw w w. h d o n l i n e s h o p. d e SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL INSTALLATION -J04479 REV.
-J04479 REV. 008-- SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL Kit Numbers 95-08A, 9006-09A Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories
More informationService Bulletin CL Warranty Extension: EGR Port Clogging. December 17, (Supersedes , dated October 26, 2001)
Service Bulletin 99-045 Applies To: 1997 99 3.0CL ALL December 17, 2001 3.0CL Warranty Extension: Port Clogging (Supersedes 99-045, dated October 26, 2001) BACKGROUND In some areas of the U.S., certain
More information2. Disconnect negative battery cable to avoid possible fuel discharge if an accidental attempt is made to start the engines.
PART #25001 LT1 Adjustable Fuel Pressure Regulator, 1994-1997 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION
More informationTURBOCHARGER Toyota Celica DESCRIPTION OPERATION TURBOCHARGING SYSTEMS All Models
TURBOCHARGER 1988 Toyota Celica 1988 TURBOCHARGING SYSTEMS All Models DESCRIPTION Most models use a water-cooled turbocharger, mounted directly to the exhaust manifold with a wastegate assembly attached
More informationNo part of this publication may be reproduced without written permission.
Thank you for purchasing a Honda generator. This manual covers operation and maintenance of the EB3000 and EB4000 generators. All information in this publication is based on the latest product information
More informationExhaust System Installation for Audi S4, S5 & S5 Sportback PNs ,
Exhaust System Installation for Audi S4, S5 & S5 Sportback PNs 140740, 140749 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary
More information2003 Hyundai Sonata LX
TIMING & COUNTERBALANCE SHAFT BELTS Removal CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate
More informationMazda North American Operations Irvine, CA
Service Bulletin Mazda North American Operations Irvine, CA 92618-2922 Subject: VARIABLE VALVE TIMING (VVT) NOISE AND/OR TIMING CHAIN NOISE Bulletin No: 01-012/12 MULTI-MODEL (L3 TURBO) - VARIABLE VALVE
More informationSCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT
-J04479 REV. 009-06-0 SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT GENERAL Kit Numbers 95-08A, 9006-09A, 876-0 Models For model fitment information, see the P&A Retail Catalog or the Parts
More informationQualified Manufacturer Declared Modified Part FOR CLOSED COURSE COMPETITION ONLY; NOT INTENDED FOR STREET USE
RESEARCH&DEVELOPMENT OF AMERICA, INC. 5420 DANIELS STREET STE A, CHINO CA., 91710 (800) 634-9166 (909) 628-4722 FAX (909) 591-2198 www.yoshimura-rd.com RACE SERIES Qualified Manufacturer Declared Modified
More informationDrive Axles SHAIS171. The Dana LMS Hub is available on the following Steer and Drive Axle Models:
Information Sheet Spicer Drive Axles SHAIS171 Topic: Dana LMS Hub Assembly Procedure Steer and Drive Axles Note: Bulletin ABIB-0302 replaces the original bulletin ABIB-9606. The Dana LMS hub design eliminates
More informationREF QTY PART DESCRIPTION PART NUMBER
USB RETROFIT KIT P/N 2883689, 2883690 APPLICATION Verify accessory fitment at www.indianmotorcycle.com. Kit PN 2883690: All 2018 and older Indian Scout and Scout Bobber Models Kit PN 2883689: 2019 and
More informationInstallation Instructions for Scion FR-S, Toyota FT86, or Subaru BRZ PN-11839, 11937
Installation Instructions for Scion FR-S, Toyota FT86, or Subaru BRZ PN-11839, 11937 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the
More informationTHIS PRODUCT IS DESIGNED FOR USE IN CLOSED COURSE RACING AND IS NOT INTENDED FOR HIGHWAY USE.
RESEARCH&DEVELOPMENT OF AMERICA, INC. 5420 DANIELS STREET STE A, CHINO CA., 91710 (800)634-9166 (909)628-4722 FACSIMILE (909)591-2198 www.yoshimura-rd.com YOSHIMURA PERFORMANCE EXHAUST SYSTEM 2006-2007
More informationREGULATORS ALPHA 8 SECOND STAGE OCEANIC ALPHA 8 SERVICE PROCEDURE
OCEANIC ALPHA 8 SERVICE PROCEDURE This Alpha 8 Service Procedure conveys a list of components and service procedures that reflect the Alpha 8 as it was configured at the time of this writing (2/19/05).
More informationRead all instructions carefully before attempting installation. REV DSL
Corporate Office: PerTronix Inc. 440 E. Arrow Highway, San Dimas, California 91773 * Phone 909.599.5955 FAX 909.599.6424 Installation Instructions And Warranty Information Part # 6830S ~ Small Block Chevrolet
More informationInstruction Manual Speed meter Kit for XR50 / XR100 Motard
Thank you for purchasing one of our TAKEGAWA-made products. Please strictly follow the following instructions in installing and using the kit. Before installing the kit, please be sure to check the kit
More informationOverhead Set ( )
Overhead Set Overhead Set (003-004) Page 1 of 17 Table of Contents Summary General Information Preparatory Steps Adjust CELECT or CELECT Plus STC Finishing Steps Summary Disconnect batteries. Refer to
More informationInstallation Instructions and Warranty Information
Corporate Office: PerTronix Inc. 440 E. Arrow Highway, San Dimas, California 91773 * Phone 909.599.5955 FAX 909.599.6424 Installation Instructions and Warranty Information Chevrolet & GMC Silverado/Sierra,
More informationInstallation Instructions
SLP GM/Chevrolet LS3 COIL COVER KIT 2010+ Camaro 5.3L/6.2L 2007+ GMT900 5.3L/6.2L PN: 620038 Installation Instructions Important Notes: Before installing your SLP Coil Cover Kit, please read the installation
More informationHI-FLOW FUEL RAIL. Installation Instructions for Scion tc & xb AEM Fuel Rail AN Hose adaptor
HI-FLOW FUEL RAIL Installation Instructions for 08-10 Scion tc & xb 25-170 AEM Fuel Rail 2-661 -6 AN Hose adaptor AEM Performance Electronics INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:
More informationFOR SAFE OPERATION. * Exhaust contains poisonous carbon monoxide Avoid inhalation of exhaust gases. Never engine in a closed garage or confined area.
FOR SAFE OPERATION WARNING: * To prevent fire hazards and to provide adequate ventilation, keep the engine at least 3 ft away from buildings and other equipment, during operation. * Do not place flammable
More informationInstallation Instructions
Parts Installation Instructions DESCRIPTION PART # QTY A Alignment Tab PN ESB101 1 B Drill Guide PN ESB102 1 C Actuator Cable Assembly PN ESB103 1 C1 72 Actuator Cable 1 C2 5/16 Jam Nut 1 C3 Star Washer
More informationChevrolet Camaro (Gen6) Installation Guide Long Tube Header PN 17293*
BORLA PERFORMANCE INDUSTRIES Chevrolet Camaro (Gen6) Installation Guide Long Tube Header PN 17293* ***** Please compare the parts in the box with the bill of materials provided ***** (view the following
More information2016+ Camaro V8 or V6/I4 Exhaust Kit
2016+ Camaro V8 or V6/I4 Exhaust Kit Installation Instructions P/N: 620079 (99-135) P/N: 620078 (99-136) 39555 Schoolcraft Rd, Plymouth MI, 48170 855.SLP.PERF 2016+ Camaro V8 or V6/I4 Exhaust Kit Installation
More informationS&S. S&S Oil Supply Line Installation Kit PN (For Harley-Davidson Dyna Models) PN (For FLT Models)
Instruction 510-0039 03-07-13 Copyright 2011, 2013 by S&S Cycle, Inc. All rights reserved. Printed in the U.S.A. S&S Cycle, Inc. 14025 County Highway G PO Box 215 Viola, Wisconsin 54664 Phone: 608-627-1497
More informationMODEL MODEL NUMBER SERIAL NUMBER
WARRANTY BULLETIN Warranty Campaign CAN-AM SSV CAUTION: All involved customers must be notified, all involved units must be corrected as per instruction herein. May 6, 2014 Campaign no.: 2013 0016 2013
More informationS&S Cycle, Inc County Hwy. G Box 215 Viola, Wisconsin U.S.A.
Instruction Sheet 51-1046 1-28-03 Copyright 1999, 2003 by S&S Cycle, Inc. All rights reserved. Printed in the U.S.A. S&S Cycle, Inc. 14025 County Hwy. G Box 215 Viola, Wisconsin 54664 U.S.A. Phone 608-627-2080
More informationInstallation Instructions for S&S Single Bore Throttle Bodies
Instruction 51-1239 12-29-15 Rev 2 Copyright 2009, 2015 by S&S Cycle, Inc. All rights reserved. Printed in the U.S.A. S&S Cycle, Inc. 14025 Cty Hwy G PO Box 215 Viola, Wisconsin 54664 Phone: 608-627-1497
More informationFUEL SYSTEM PRECAUTION FU 1
2GR-FE EL EL SYSTEM EL SYSTEM PRECAUTION 1 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of the ignition switch used on this model differs according to the specifications of the vehicle. The expressions
More information