Maintenance Manual WATER SUMP CONTROL VALVE F532B

Size: px
Start display at page:

Download "Maintenance Manual WATER SUMP CONTROL VALVE F532B"

Transcription

1 WATER SUMP CONTROL VALVE F532B

2 LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical line in the outer margin of the page. When a revision is issued, the entire document is reissued with the current revision number and date shown on all pages. For major revisions, the basic number is incremented. For minor revisions, the number following the decimal is incremented. Dates of issue for original and subsequent revisions are as follows: Original /01/2004 The total number of pages in this technical document is 16 consisting of the following: Title, A, 1 14 TABLE OF CONTENTS SUBJECT PAGE Introduction 1 Description and Operation 1 Fault Isolation 4 Disassembly 6 Cleaning 7 Inspection 8 Assembly 9 Testing 11 Illustrated Parts List 12

3 1. General INTRODUCTION This manual provides component maintenance shop instructions for the Water Sump Control Valve (valve). 2. Revision Service This manual will be revised as necessary to show the current information. 3. Weights and Measurements Weights and measurements in this manual are expressed in both English (U.S. customary) and Metric (SI) units. 1. Description DESCRIPTION AND OPERATION The Water Sump Control Valve (valve) (see Figures 1 and 2) provides the means of detecting free water accumulation in filter/separators, storage tanks and other refueling system components. The major functional components of the valve are the float, the valve, the sump and the plunger assembly. 2. Operation A. Negligible Free Water Accumulation When the accumulated free water in the sump is negligible, the specific gravity of the float is sufficient to keep it from floating, and the refueling system operates normally. B. Excessive Free Water Accumulation As free water accumulates, its higher specific gravity causes the float to move upward. When the free water accumulation is sufficient, float movement actuates its normally open valve closes and opens a path for the system reference pressure to vent. When this occurs, the refueling system shuts down due to the lack of reference pressure to its control valves.

4 C. Refueling System Restart When the refueling system has been shut down due to excessive free water accumulation in the valve sump, operator action is required to drain the water. When the water has drained, the float will sink, the vent valve will close, and normal operation will resume. D. Pre-Check Plunger The pre-check plunger provides the means to verify proper operation of the valve. When the plunger is pushed, it manually lifts the float and operates the valve, causing system reference pressure to vent. An audible sound is produced when the system reference pressure vents. The pre-check plunger should be used periodically, in accordance with the operator s established operating procedures. E. Reference Pressure Source The valve can operate with reference air or fuel pressure. Reference air can be vented to the atmosphere. Reference fuel pressure must be vented to a low pressure purge tank. 3. Leading Particulars (Refer to Table 1) Table 1. Leading Particulars Service Automotive and Aviation Fuels and Water Operating Pressure Maximum Working 200 psi (1 380 kpa) Through Valve 85 psi (590 kpa) Fluid Temperature 35 to 135 F ( 37 to 57 C) Ambient Temperature 65 to 160 F ( 54 to 71 C) Weight (approximate) 15 pounds (6,8 kg) (Specific gravity: 0.83 maximum)

5 FAULT ISOLATION 1. General Refer to Table 2 for fault isolation information. Locate suspected faulty component and take appropriate remedial action. Table 2. Fault Isolation FAULT POSSIBLE CAUSE CORRECTIVE ACTION Valve will not close Pivot (15, IPL Figure 1) improperly adjusted Seat in valve body (12) excessively worn or damaged due to contamination Table 2. Fault Isolation Adjust the pivot (refer to ASSEMBLY section, paragraph 3F). Replace the valve body. FAULT POSSIBLE CAUSE CORRECTIVE ACTION Valve will not close Leakage from the vent port Weight of float assembly (items 16 through 19) is incorrect Reference pressure inlet and outlines switched Seat of poppet (6) excessively worn or damaged due to contamination Seat in valve body (12) excessively worn or damaged due to contamination Check and correct the float weight (refer to ASSEMBLY paragraph 3F). Reverse the lines. Replace the poppet. Replace the valve body.

6 Fuel to air leakage contamination Pivot (15) improperly adjusted Weight of float assembly (items 16 through 19) is incorrect Damaged quad rings (9) due to contamination Adjust the pivot (refer to ASSEMBLY section, paragraph 3F). Check and correct the float weight (refer to ASSEMBLY paragraph 3B). Replace the quad rings. DISASSEMBLY NOTE: Prior to disassembly, the vessel in which the water sump control valve is installed must be drained in accordance with the applicable instructions, and the water sump control valve must be disconnected and removed from the vessel. 1. Seal Replacement Parts Kits Refer to the ILLUSTRATED PARTS LIST section for the Replacement Parts Kit information. 2. Disassembling the Water Sump Control Valve (Refer to IPL Figure 1) A. Remove the packing (20) from the packing groove of the sump (21). B. Remove the screws (7), the washers (8), the cap (1), the spring (5) and the poppet (6) from the valve body (12). Remove the packings (2 and 4) and the packing cap (3) from the valve body. C. Remove the screws (10), the washers (11) and gently pull the valve body (12) away from the sump (21). Using a suitable small diameter tool (a straightened large paper clip works well), push out the pin (16), and remove the valve body and associated parts. D. Remove the packing (13) and the pivot (15) from the valve body. CAUTION: BE CAREFUL NOT TO CHANGE THE SETTING OF THE PIVOT (15). IT IS SET AT THE FACTORY TO THE DIMENSION SHOWN IN FIGURE 2. E. Remove the rod (14) from the valve body (12). Remove the packings (9) from the rod. F. Remove the float from the sump. Remove the plug (17) and the packing (18) from the float. G. If there has been leakage from the plunger assembly, remove the plug (22.1) from the sump (21). Remove the ring (22.5) from the plunger (22.2). Remove the plunger (22.2), the backup ring (22.3), and the packings (22.4) from the plug

7 CLEANING 1. Cleaning Materials Refer to Table 4 for recommended cleaning materials. Suitable equivalent cleaning materials may be substituted for the items listed. Table 4. Recommended Cleaning Materials DESCRIPTION SPECIFICATION SOURCE Brush, Bristle, stiff, nonmetallic Commercially available Dry Cleaning Solvent P-D-680, Type 2 Commercially available Pick, Teflon Commercially available Plastic Bags Commercially available Tissues, lint-free Commercially available 2. Cleaning Procedures WARNING: DRY CLEANING SOLVENT IS FLAMMABLE AND TOXIC TO EYES, SKIN, AND RESPIRATORY TRACT. SKIN/EYE PROTECTION REQUIRED. AVOID REPEATED/PROLONGED CONTACT. USE ONLY IN WELL VENTILATED AREAS. GOOD GENERAL VENTILATION IS NORMALLY ADEQUATE. KEEP AWAY FROM OPEN FLAMES OR OTHER IGNITION SOURCES. A. Clean all metal parts by washing thoroughly in dry cleaning solvent. Remove stubborn deposits by scrubbing with a nonmetallic stiff bristle brush. Use a Teflon pick to remove obstructions from ports, grooves and passages. NOTE: All of the parts must be free of corrosion, dirt, grease, oil, or any other foreign matter. WARNING: WEAR EYE PROTECTION WHEN DRYING PARTS WITH COMPRESSED AIR. DO NOT DIRECT AIRSTREAM AT PERSONNEL OR LIGHT METAL PARTS. B. Dry parts with clean lint-free tissues or clean, dry compressed air. C. Package clean parts in plastic bags.

8 INSPECTION 1. General A. Under strong light and magnification, visually check all parts in accordance with the general criteria specified in paragraph 2 below. B. Repair minor damage in accordance with local directives. If damage is major or beyond simple repair, replace the part rather than attempt extensive repairs. 2. Component Checks (Refer to Table 5) DESCRIPTION Table 5. Component Checks (IPL Figure 1 Item Number) General Poppet (6) Rod (14) CHECK CRITERIA Visually check all parts as applicable for nicks, cracks, cuts, burrs, corrosion, breaks, scoring, chafing, scarring, deformation, dents, thread damage, or any other obvious defects. Make sure that the ports, passages, recesses and sealing grooves are clean and unobstructed. Check all sealing and seating surfaces for damage or corrosion that would affect sealing. The inside and outside diameters must be free of scratches. The air passages must not be obstructed (free air flow is critically important). The seating faces must be free of scratches.

9 ASSEMBLY 1. Overhaul and Seal Replacement Parts Kits Refer to the ILLUSTRATED PARTS LIST section for the recommended seal and overhaul replacement parts kit information. 2. Assembly Materials Refer to Table 7 for recommended assembly materials. Suitable equivalent materials may be substituted for the items listed. Table 7. Recommended Assembly Materials DESCRIPTION SPECIFICATION SOURCE Grease, Silicone 33 Dow Corning (commercially available) 3. Assembling the Water Sump Control Valve (Refer to IPL Figure 1) A. Lubrication Prior to assembly, lightly lubricate all of the packings, seals and screw threads with silicone grease (#33). B. Assembling the Float Assembly Fill the float (19) with water to a weight of 4.15 (±0.05) pounds (1,87 to 1,90 kg) (including the packing (18) and the plug (17). Tighten the plug securely. CAUTION: DO NOT STRETCH THE PACKING CAP (3). BE CAREFUL NOT TO CREASE THE PACKING CAP DURING INSTALLATION. C. Install the packing (2) in the cap (1). Gently roll the packing cap (3) so that it will form around the packing. Install the packing cap on the packing. D. Lightly lubricate the inside diameter of the poppet (6) with silicone grease (#33). Install the poppet and the spring (5) in the cap (1). E. Install the quad rings (9) in the grooves of the rod (14). Lightly lubricate the quad rings (on the rod) with silicone grease (#33).

10 F. Install the rod (14) in the valve body (12). Install the packing (13) in the packing groove of the valve body. Make sure that the pivot is installed in accordance with the dimensional requirement of Figure 3. G. Install the float assembly (items 17, 18 and 19) in the sump (21). H. Hook the pin on the float (19) into the groove of the rod (14). Line up the hole of the pivot (15) with the holes in the lever of the float and install the pin (16). I. Make sure that the packing (13) is correctly seated in its groove on the valve body (12). Secure the valve body to the sump with the screws (10) and the washers (11). J. Install the cap (1) on the valve body (12) and secure it with the screws (7) and the washers (8). K. Assembling the Plunger Assembly Install the plunger (22.1) with new packings (22.4) and a new backup ring (22.3) in the plug (22.1). Install the ring (22.4) on the plunger. L. Install the plunger assembly (22) in the sump (21). Tighten the plug (22.1) securely. TESTING NOTE: Prior to testing, the vessel in which the water sump control valve is installed must be drained in accordance with the applicable instructions, and the valve must be disconnected and removed from the vessel. 1. Leakage and Functional Test A. Connect a regulated air pressure source (85 psig maximum) to the PRESSURE INLET port. B. Connect a pressure gage to the PRESSURE OUTLET port. C. Connect an open line to the VENT port. WARNING: AVIATION FUEL IS FLAMMABLE AND TOXIC TO YOUR EYES, YOUR SKIN, AND YOUR RESPIRATORY TRACT. SKIN AND EYE PROTECTION IS REQUIRED. AVOID REPEATED OR PROLONGED CONTACT. KEEP AWAY FROM OPEN FLAMES OR OTHER IGNITION SOURCES.

11 D. Immerse the valve with its mounting flange horizontal and facing upward in a container of clean aviation fuel. Pressurize the inlet port to 60 psig. E. The float must remain in its fully down position. No air bubbles (indicating external leakage) should be visible. F. Vent the test pressure to 0 psig. Remove the water sump control valve from the container and blow it dry with shop air. G. Immerse the valve with its mounting flange horizontal and facing upward in a container of clean water. Do not pressurize the inlet port. H. The float should rise to its fully up position. I. Manually push the float to its fully down position and hold it down. Pressurize the inlet port to 60 psig. The pressure gage should indicate 60 psig. J. Release the float. Air should vent from the open line. The pressure gage should indicate 0 psig. K. Manually push the float to its fully down position and hold it down. The pressure gage should indicate 60 psig. L. Vent the test pressure to 0 psig. Remove the valve from the container and thoroughly dry it with shop air. Disconnect the valve from the test setup.

12 ILLUSTRATED PARTS LIST 1. General This section lists, describes, and illustrates all detail parts required for maintenance support of the Water Sump Control Valve. 2. Scope of Information A. The parts list is indentured to show the relationship between each part and its next higher assembly. Item numbers used in the parts list are keyed to the corresponding numbers of the accompanying illustration. B. Abbreviations ASSY FIG. MOD REF Assembly. Figure. Modification. Reference item. KIT REPLACEMENT PARTS KITS AVAILABLE ITEMS IN KIT PART NUMBER DESCRIPTION (IPL Figure 2) KITF532-1 Seal Replacement 2, 3, 4, 9, 13 and Overhaul 2, 3, 4, 6, 7, 8, 9, 10, 11, 13 and 20

13 FIG. DESCRIPTION MOD UNITS ITEM PART NUMBER CODES PER ASSY 1 F532B VALVE, WATER SUMP CONTROL REF 1 F60W CAP BD019 PACKING, PREFORMED 1 3 DW CAP, PACKING SPECIAL A031 PACKING, PREFORMED 1 5 F60W1811 SPRING, COMPRESSION 1 6 F60W1810 POPPET 1 7 CAN500C10-28 SCREW, MACHINE 4 8 CMS WASHER, LOCK 4 9 Q Y RING, QUAD 3 10 CAN SCREW, MACHINE WASHER, FLAT BODY, VALVE (Aluminum alloy) A133 PACKING, PREFORMED 1 14 F60W1809 ROD 1 15 F60W1628? PIVOT 1 16 F60W1627 PIN, HINGE 1 17 CAN814-16D? PLUG 1 18 CMS PACKING, PREFORMED 1? 19 F60W1649 FLOAT A266 PACKING, PREFORMED 1 21 F60W SUMP (Aluminum alloy) SUMP (Aluminum alloy) (Alternate for 1 F60W1622-2) PLUNGER ASSEMBLY PLUG 1

14 FIG. DESCRIPTION MOD UNITS ITEM PART NUMBER CODES PER PLUNGER CMS RING, BACKUP BD0 PACKING, PREFORMED X3/32 RING, SPLIT 1 RR138 RING, SPLIT (Alternate for 1X3/32) 1 ASSY

Water Slug Control Switch F528/F528B Series

Water Slug Control Switch F528/F528B Series Water Slug Control Switch F528/F528B Series Whittaker Controls Avery-Hardoll 12838 Saticoy Street Holland Way North Hollywood Blandford Forum CA 91605-3505 Dorset DT11 7BJ USA UK Tel: +1 818 765 8160 Tel:

More information

Maintenance Manual. 4-Inch Internal Valve. F614 Series

Maintenance Manual. 4-Inch Internal Valve. F614 Series 4-Inch Internal Valve F614 Series LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical line in the outer margin of the page.

More information

Maintenance Manual 6-INCH INTERNAL VALVE F620 SERIES

Maintenance Manual 6-INCH INTERNAL VALVE F620 SERIES Maintenance Manual 6-INCH INTERNAL VALVE F620 SERIES REVISION 1.1 03/15/2002 LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical

More information

Maintenance Manual 3-INCH INTERNAL VALVE F660 SERIES

Maintenance Manual 3-INCH INTERNAL VALVE F660 SERIES Maintenance Manual 3-INCH INTERNAL VALVE F660 SERIES REVISION 1.1 03/15/2002 LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical

More information

Maintenance Manual. 3-Inch Internal Valve. F660 Series

Maintenance Manual. 3-Inch Internal Valve. F660 Series 3-Inch Internal Valve F660 Series LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical line in the outer margin of the page.

More information

Maintenance Manual. Hydrant Coupler. F250 Series

Maintenance Manual. Hydrant Coupler. F250 Series Hydrant Coupler F250 Series LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical line in the outer margin of the page. When

More information

Maintenance Manual 4½-INCH INTERNAL VALVE F635 SERIES

Maintenance Manual 4½-INCH INTERNAL VALVE F635 SERIES Maintenance Manual 4½-INCH INTERNAL VALVE F635 SERIES REVISION 1.0 11/01/2004 LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical

More information

Maintenance Manual HOSE END PRESSURE CONTROL VALVE F594 / F595 SERIES

Maintenance Manual HOSE END PRESSURE CONTROL VALVE F594 / F595 SERIES Maintenance Manual HOSE END PRESSURE CONTROL VALVE F594 / F595 SERIES NOTICE: PROPRIETARY INFORMATION OF WHITTAKER CONTROLS, INC., A BUSINESS UNIT OF MEGGITT PLC. THE INFORMATION CONTAINED IN THIS DOCUMENT

More information

Maintenance Manual BARRIER SERVO ASSEMBLY F1510 SERIES

Maintenance Manual BARRIER SERVO ASSEMBLY F1510 SERIES Maintenance Manual BARRIER SERVO ASSEMBLY F1510 SERIES NOTICE: PROPRIETARY INFORMATION OF, A BUSINESS UNIT OF MEGGITT PLC. THE INFORMATION CONTAINED IN THIS DOCUMENT IS DISCLOSED IN CONFIDENCE. IT IS THE

More information

Maintenance Manual HYDRANT SHUTOFF VALVE F352 / F353 SERIES

Maintenance Manual HYDRANT SHUTOFF VALVE F352 / F353 SERIES Maintenance Manual HYDRANT SHUTOFF VALVE F352 / F353 SERIES NOTICE: PROPRIETARY INFORMATION OF WHITTAKER CONTROLS, INC., A BUSINESS UNIT OF MEGGITT PLC. THE INFORMATION CONTAINED IN THIS DOCUMENT IS DISCLOSED

More information

Maintenance Manual UNDERWING REFUELING NOZZLE F116 SERIES

Maintenance Manual UNDERWING REFUELING NOZZLE F116 SERIES Maintenance Manual UNDERWING REFUELING NOZZLE F116 SERIES NOTICE: PROPRIETARY INFORMATION OF WHITTAKER CONTROLS, INC., A BUSINESS UNIT OF MEGGITT PLC. THE INFORMATION CONTAINED IN THIS DOCUMENT IS DISCLOSED

More information

Pressure Control Coupler F239 Series

Pressure Control Coupler F239 Series Pressure Control Coupler F239 Series Whittaker Controls 12838 Saticoy Street North Hollywood CA 91605-3505 USA Tel: +1 818 765 8160 Fax: +1 818 759 2194 www.wkr.com www.meggittfuelling.com www.meggitt.com

More information

Hydrant Coupler F211 Series

Hydrant Coupler F211 Series Hydrant Coupler F211 Series Whittaker Controls Avery-Hardoll 12838 Saticoy Street Holland Way North Hollywood Blandford Forum CA 91605-3505 Dorset DT11 7BJ USA UK Tel: +1 818 765 8160 Tel: +44 (0) 1258

More information

Underwing Refuelling Nozzle F116 Series

Underwing Refuelling Nozzle F116 Series Underwing Refuelling Nozzle F116 Series MMF116 Revision 2.0 01 August 2013 Meggitt (North Hollywood), Inc. Proprietary Information The information contained in this document is disclosed in confidence.

More information

F582/F584 MAINTENANCE MANUAL

F582/F584 MAINTENANCE MANUAL F582/F584 MAINTENANCE MANUAL 1. DESCRIPTION AND OPERATION 1.1 DESCRIPTION The F582/F584 Swivel Disconnects are designed to provide the ability to custom build a Nozzle or Hydrant Coupler system to meet

More information

SD Bendix TC-4 Modulating Control Valve TYPICAL PIPING DIAGRAM EXHAUST PORT DELIVERY PORT DELIVERY PORT FIGURE 1 SUPPLY PORT FIGURE 2

SD Bendix TC-4 Modulating Control Valve TYPICAL PIPING DIAGRAM EXHAUST PORT DELIVERY PORT DELIVERY PORT FIGURE 1 SUPPLY PORT FIGURE 2 SD-03-4503 Bendix TC-4 Modulating Control Valve EXHAUST DELIVERY DELIVERY FIGURE 1 SUPPLY TC-2 TP-2 TRAILER SERVICE BRAKE CHAMBERS GAUGE TW-1 MANIFOLD TC-2 SV-1 DS-1 COUPLINGS TRAILER EMERGENCY SPRING

More information

SD Bendix R-6 Relay Valve DESCRIPTION OPERATION

SD Bendix R-6 Relay Valve DESCRIPTION OPERATION SD-03-1060 Bendix R-6 Relay Valve SUPPLY PORT (RESERVOIR MOUNT TYPE) SERVICE PORT RETURN SPRING RELAY PISTON DELIVERY PORTS (4) SUPPLY PORT EXHAUST R-6 RELAY VALVE INSERT FIGURE 1 FIGURE 2 DESCRIPTION

More information

Warning and Safety Precautions

Warning and Safety Precautions EXPRESS WARRANTY AND DISCLAIMER OF IMPLIED WARRANTIES Lily Corporation unconditionally guarantees its products to be free of defects in material or workmanship and further warrants that, for a period of

More information

Defender Series. Overfill Prevention Valve. Automatic Shutoff for USTs. Installation, Operation and Maintenance Series

Defender Series. Overfill Prevention Valve. Automatic Shutoff for USTs. Installation, Operation and Maintenance Series Defender Series Overfill Prevention Valve Automatic Shutoff for USTs Installation, Operation and Maintenance 708-590 Series For use in 4" gravity-fill applications only 25-370 Gallons per Minute flow Compatible

More information

3/8" NPT PISTON SPRING INLET EXHAUST VALVE SPRING LOWER PISTON ASSEMBLY

3/8 NPT PISTON SPRING INLET EXHAUST VALVE SPRING LOWER PISTON ASSEMBLY SD-03-951 Bendix LQ-3 & LQ-4 * Front Axle Ratio Valve 1/4" NPT 3/8" NPT INLET LOWER ASSEMBLY 1/4" NPT 3/8" NPT HOLD OFF (WHEN REQUIRED) LQ-3 FRONT AXLE RATIO LQ-4 FRONT AXLE RATIO * (*THE LQ-4 'S OPERATION

More information

SECONDARY SERVICE EXTERIOR R-12DC VALVE (MODEL WITH 4 VERTICAL DELIVERY PORTS) DELIVERY COVER SECONDARY RELAY PISTON VALVE RETAINER INLET EXHAUST

SECONDARY SERVICE EXTERIOR R-12DC VALVE (MODEL WITH 4 VERTICAL DELIVERY PORTS) DELIVERY COVER SECONDARY RELAY PISTON VALVE RETAINER INLET EXHAUST SD-03-1068 Bendix R-12DC Relay Valve with Biased Double Check PRIMARY SECONDARY EXTERIOR R-12DC (MODEL WITH 4 VERTICAL DELIVERY PORTS) SUPPLY (2) EXTERIOR R-12DC (MODEL WITH 2 HORIZONTAL PORTS) DELIVERY

More information

SYSTEM SAVER 318 AIR COMPRESSOR FOR MACK E-TECH AND ASET ENGINES MAINTENANCE MANUAL

SYSTEM SAVER 318 AIR COMPRESSOR FOR MACK E-TECH AND ASET ENGINES MAINTENANCE MANUAL SYSTEM SAVER 318 AIR COMPRESSOR FOR MACK E-TECH AND ASET ENGINES MAINTENANCE MANUAL NON-THROUGH DRIVE THROUGH DRIVE Service Notes About This Manual This manual provides service and repair procedures for

More information

SD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2

SD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2 SD-03-832 Bendix E-10PR Retarder Control Brake Valve MOUNTING PLATE SUPPLY 4 PORTS ELECTRICAL AUXILIARY DESCRIPTION TREADLE RETARDER CONTROL SECTION EXHAUST DELIVERY 4 PORTS FIGURE 1 - E-10PR RETARDER

More information

P-1 LOAD PROPORTIONAL VALVE, (60%), Pc.No

P-1 LOAD PROPORTIONAL VALVE, (60%), Pc.No P-1 LOAD PROPORTIONAL VALVE, (60%), Pc.No. 577723 DECEMBER, 1988 Supersedes issue dated November, 1976 NOTE: The following description and operation is based on this device and its components being new

More information

SD Bendix E-12 & E-15 Dual Brake Valve DESCRIPTION

SD Bendix E-12 & E-15 Dual Brake Valve DESCRIPTION SD-03-6 Bendix E- & E-15 Dual Brake Valve TREADLE UPPER BODY ASSEMBLY PRIMARY DELIVERY ( ) 1 SECONDARY DELIVERY ( ) LOWER BODY ASSEMBLY MOUNTING PLATE PRIMARY SUPPLY ( SUP-1) PRIMARY SUPPLY ( SUP-) PRIMARY

More information

MGFHVLP. Instructions/Parts. Mini Gravity Feed System E. Part No Includes MGFHVLP Mini Gravity Feed Spray Gun and MGC 125 Gravity Cup.

MGFHVLP. Instructions/Parts. Mini Gravity Feed System E. Part No Includes MGFHVLP Mini Gravity Feed Spray Gun and MGC 125 Gravity Cup. Instructions/Parts MGFHVLP Mini Gravity Feed System FOR PRODUCT INFORMATION CALL: 1-800-742-7731 309989E For gravity feed spraying of automotive colors and clears. Ideal for touch-up and detail work. Important

More information

SD Bendix MV-1 Modutrol DESCRIPTION

SD Bendix MV-1 Modutrol DESCRIPTION SD-03-3411 Bendix MV-1 Modutrol VALVE A 5-3/8 VALVE B VALVE C VALVE E VALVE D FIGURE 1 - MV-1 MODUTROL DESCRIPTION The Bendix MV-1 modutrol assembly is an integrated air control module designed for dash

More information

BRAKES. Section III REAR AXLE DATA AND SPECIFICATIONS HAND BRAKE CHRYSLER SERVICE MANUAL BRAKES 17

BRAKES. Section III REAR AXLE DATA AND SPECIFICATIONS HAND BRAKE CHRYSLER SERVICE MANUAL BRAKES 17 BRAKES 17 There is no basic design change in the rear axle and sure grip differential except the larger diameter pinion shaft is now used on all models for 1959. The Service Procedures will remain the

More information

Model Ton Hand Carry Axle Jack P/N: CJ67D0250-1

Model Ton Hand Carry Axle Jack P/N: CJ67D0250-1 Model 1504-50 15 Ton Hand Carry Axle Jack P/N: CJ67D0250-1 Operation and Maintenance Manual with Illustrated Parts List 2222 South Third Street Columbus, Ohio 43207-2402 Phone (614) 443-7492 FAX (614)

More information

Operation & Maintenance Instruction , S.9. MARCH, 2005 Supersedes issue dated March, 2003

Operation & Maintenance Instruction , S.9. MARCH, 2005 Supersedes issue dated March, 2003 S-1 LOAD SENSOR VALVES, SUSPENSION MOUNTING - PART NO. 664801-0001 SUSPENSION MOUNTING - PART NO. 665132-0001 FLOOR MOUNTING - PART NO. 664801-0002 FLOOR MOUNTING - PART NO. 665132-0002 MARCH, 2005 Supersedes

More information

S-1 LOAD SENSOR VALVES, PART NOS & PART NOS &

S-1 LOAD SENSOR VALVES, PART NOS & PART NOS & S-1 LOAD SENSOR VALVES, PART NOS. 578553-0001 & 578553-0011 PART NOS. 665133-0001 & 665133-0011 AUGUST, 2005 Supersedes issue dated December, 2004 NOTE: The following description and operation is based

More information

Removal and Installation of the DD15 and DD16 Cylinder Head April Removal of the DD15 and DD16 Cylinder Head

Removal and Installation of the DD15 and DD16 Cylinder Head April Removal of the DD15 and DD16 Cylinder Head 4 102-12 1 4 102-12 SUBJECT DATE Removal and Installation of the DD15 and DD16 Cylinder Head April 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081

More information

Anderson Greenwood Series 400 Piston Pilot POPRV Installation and Maintenance Instructions

Anderson Greenwood Series 400 Piston Pilot POPRV Installation and Maintenance Instructions Before installation these instructions must be fully read and understood As capacity relief of the system is satisfied, system pressure will begin to decrease. When it does, the pilot will actuate and

More information

Anderson Greenwood Series 800 POSRV Installation and Maintenance Instructions

Anderson Greenwood Series 800 POSRV Installation and Maintenance Instructions Before installation these instructions must be fully read and understood Table of contents 1. General valve description and start-up... 1 2. Main valve maintenance... 2 3. Pilot maintenance... 6 4. Pilot

More information

ANDERSON GREENWOOD SERIES 500 PILOT OPERATED SAFETY RELIEF VALVES INSTALLATION AND MAINTENANCE INSTRUCTIONS

ANDERSON GREENWOOD SERIES 500 PILOT OPERATED SAFETY RELIEF VALVES INSTALLATION AND MAINTENANCE INSTRUCTIONS Before installation these instructions must be fully read and understood TABLE OF CONTENTS 1. General valve description and start-up... 1 2. Main valve maintenance... 1 3. Pilot maintenance... 5 4. Pilot

More information

28-A DOUBLE CHECK VALVE PORTION, Pc. No

28-A DOUBLE CHECK VALVE PORTION, Pc. No 28-A DOUBLE CHECK VALVE PORTION, Pc. No. 650143 NOVEMBER, 1989 Supersedes issue dated January, 1989 NOTE: The following description and operation is based on this device and its components being new or

More information

TC Series Cooling Systems

TC Series Cooling Systems TC Series Cooling Systems Table of Contents Table of Contents...1 List of Figures...1 Safety...2 Introduction...2 General Specifications...2 Types of Coolant...2 Routine Maintenance...2 Surge Tank Coolant

More information

Model No. 668D3. COFFEPUMP Part No Product Code: O/C GJAN21.DB6B-DC310B

Model No. 668D3. COFFEPUMP Part No Product Code: O/C GJAN21.DB6B-DC310B Model No. 668D3 COFFEPUMP Part No. 9168 Product Code: O/C GJAN21.DB6B-DC310B OVERHAUL MANUAL with ILLUSTRATED PARTS LIST Page 1 of 15 P/N 5914 Rev D 01/17/05 1.0 Introduction 1.1 Description 1.1.1 The

More information

D Instructions/Parts. Siphon Feed Detail Spray Gun D

D Instructions/Parts. Siphon Feed Detail Spray Gun D Instructions/Parts D-5-55 Siphon Feed Detail Spray Gun FOR PRODUCT INFORMATION CALL: 1-800-742-7731 309991D Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.

More information

5. FUEL SYSTEM 5-0 FUEL SYSTEM UXV 500

5. FUEL SYSTEM 5-0 FUEL SYSTEM UXV 500 5 FUEL SYSTEM 5 SERVICE INFORMATION------------------------------------------------ 5-02 TROUBLESHOOTING----------------------------------------------------- 5-03 FUEL TANK -----------------------------------------------------------------

More information

Operation and Maintenance Manual

Operation and Maintenance Manual Operation and Maintenance Manual MODEL S-216-J-( ) Series AIR-DRIVEN HYDRAULIC PUMP ISSUED NOVEMBER 1994 Revised February 2005 Sprague Products Division of Curtiss-Wright Flow Control Corporation 10195

More information

SD Bendix RE-6 and RE-6NC Relay Valves RE-6. Valve. RE-6 & RE-6NC Valves RE-6NC. Valve RE-6 VALVE DESCRIPTION

SD Bendix RE-6 and RE-6NC Relay Valves RE-6. Valve. RE-6 & RE-6NC Valves RE-6NC. Valve RE-6 VALVE DESCRIPTION SD-03-1151 Bendix RE-6 and RE-6NC Relay s PISTON RELAY PISTON SERVICE PORT SEALING RING O-RING INLET AND EXHAUST VALVE RE-6 SPRING SUPPLY PORT CHECK VALVE MOUNTING FLANGE SPRING RE-6 & RE-6NC s RESERVOIR

More information

SECTION 4 - FUEL/LUBRICATION/COOLING

SECTION 4 - FUEL/LUBRICATION/COOLING For Arctic Cat Discount Parts Call 606-678-9623 or 606-561-4983 SECTION 4 - FUEL/LUBRICATION/COOLING 4 TABLE OF CONTENTS Carburetor Specifications... 4-2 Carburetor Schematic... 4-2 Carburetor... 4-3 Cleaning

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE NUMBER: 10 01 12 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

Purging Air From Divider Block Lubrication Systems

Purging Air From Divider Block Lubrication Systems FROST ENGINEERING SERVICE Purging Air From Lubrication Systems A D I V I S I O N O F G E C S E Y S A L E S & S E R V I C E DESCRIPTION Divider block lubrication systems operate correctly only when all

More information

SD Bendix PP-7 Trailer Supply Valve FUNCTION AND DESCRIPTION

SD Bendix PP-7 Trailer Supply Valve FUNCTION AND DESCRIPTION SD-03-3617 Bendix PP-7 Trailer FUNCTION AND DESCRIPTION NUT & THREAD 1/8 P.T. SUPPLY EXHAUST The PP-7 trailer supply valve provides in cab control for the tractor protection system and functions in conjunction

More information

ANDERSON GREENWOOD. Before installation these instructions must be fully read and understood.

ANDERSON GREENWOOD. Before installation these instructions must be fully read and understood. ANDERSON GREENWOOD Before installation these instructions must be fully read and understood. 1.1 General The Anderson Greenwood Series 200 Pilot Operated SRV uses the principle of pressurizing the larger

More information

SD Bendix MV-3 Dash Control Module DESCRIPTION. Bottom View

SD Bendix MV-3 Dash Control Module DESCRIPTION. Bottom View SD-03-3415 Bendix MV-3 Dash Control Module MOUNTING PLATE MOUNTING HOLES (4) Dual Circuit SUPPLY Check VALVE AUXILIARY PORT (Optional) delivery DESCRIPTION secondary supply Trailer delivery FIGURE 1 -

More information

Temperature Sensor Series

Temperature Sensor Series GENERAL DESCRIPTION The patented* No. 85026-Series Temperature Sensor contains a two-position valve operated by temperature variations around the integral sensing bulb. It is used to vent or block a pneumatic

More information

DESCRIPTION & OPERATION

DESCRIPTION & OPERATION 2004 BRAKES Disc - TSX DESCRIPTION & OPERATION WARNING: DO NOT use air pressure or a dry brush to clean brake assemblies. Avoid breathing brake dust. Use OSHA-approved vacuum cleaner for cleaning and collecting

More information

Pressure Relief Valve Maintenance Manual

Pressure Relief Valve Maintenance Manual Technical Manual 1098T Pressure Relief Valve Maintenance Manual Farris Engineering Division of Curtiss-Wright Flow Control Corporation TABLE OF CONTENTS - Manual Revision 0 Introduction & Safety Tips...

More information

SD Bendix SR-5 Trailer Spring Brake Valve DESCRIPTION PORTS. 1-1/2" or 3/4" NPT Spring Brake Reservoir Mounting (SPR BK RES)

SD Bendix SR-5 Trailer Spring Brake Valve DESCRIPTION PORTS. 1-1/2 or 3/4 NPT Spring Brake Reservoir Mounting (SPR BK RES) SD-03-4516 Bendix SR-5 Trailer Spring Brake Valve PRESSURE PROTECTION SR-5 IDENTIFICATION HOLE 1/4 NPT (2) COVER* FIGURE 1 DESCRIPTION 1/4 NPT TRAILER 1/4 NPT SR-5 TRAILER *SHOWN WITH OPTIONAL ANTI-COMPOUNDING

More information

SD Bendix TP-4 Tractor Protection Valve (Formerly VM-1) DESCRIPTION

SD Bendix TP-4 Tractor Protection Valve (Formerly VM-1) DESCRIPTION SD-03-3653 Bendix TP-4 Tractor Protection Valve (Formerly VM-1) CIRCUIT DELIVERY PORT (SCD) PRIMARY CIRCUIT DELIVERY PORT (PCD) EMERG. STOP LIGHT SWITCH (TE-SLS) PORT EMERG. SUPPLY (TES) PORT MOUNTING

More information

Crispin Valves Operating Guide. Crispin

Crispin Valves Operating Guide. Crispin Crispin Valves Operating Guide Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 www.crispinvalve.com sales@crispinvalve.com

More information

1/2" AIR DRIVEN DIAPHRAGM PUMP

1/2 AIR DRIVEN DIAPHRAGM PUMP 1/2" DRIVEN DIAPHRAGM PUMP OPERATION AND SERVICE GUIDE O-1225D NOV. 2008 Page 1 of 6 Refer to Bulletin P-605, Parts List P-9151 DRIVEN, DOUBLE DIAPHRAGM PUMP MANUAL Congratulations on purchasing one of

More information

Installation Manual For ISL98, ISL03, ISL07, ISC07

Installation Manual For ISL98, ISL03, ISL07, ISC07 Installation Manual For ISL98, ISL03, ISL07, ISC07 Table of Contents Section 1: Introduction... 3 Housing Identification... 3 Engine Identification... 3 Special Tools... 3 Automatic Transmissions... 3

More information

#8 VENT VALVE with BRANCH PIPE TEE, Part No

#8 VENT VALVE with BRANCH PIPE TEE, Part No #8 VENT VALVE with BRANCH PIPE TEE, Part No. 579076 JANUARY, 001 Supersedes Issue dated November, 1988 NOTE: The following description and operation is based on this device and its components being new

More information

Power Train. Chapter 5

Power Train. Chapter 5 Chapter Power Train Spefications................................................................. -3 Test Spefications........................................................ -3 Repair Spefications.......................................................

More information

CHAPTER 22 SERVICING

CHAPTER 22 SERVICING CHAPTER 22 SERVICING Section Title 22-10 Main Rotor Gearbox......................................... 22.1 22-11 Cleaning Chip Detector..................................... 22.3 22-12 Cleaning Sight Gage.......................................

More information

CHESTER HOIST AIR LOW HEADROOM CHAIN HOISTS AL-680 SECTION A

CHESTER HOIST AIR LOW HEADROOM CHAIN HOISTS AL-680 SECTION A CHESTER HOIST AIR LOW HEADROOM CHAIN HOISTS AL-680 SECTION A OPERATING and MAINTENANCE INSTRUCTIONS FOR AL SERIES HOISTS Users should refer to the ANSI B30.16 American National Standard and ASME HST-5M

More information

M-3025CB-AV Fuel Pump

M-3025CB-AV Fuel Pump SAVE THESE INSTRUCTIONS M-3025CB-AV Fuel Pump Owner s Manual TABLE OF CONTENTS General Information... 2 Safety Instructions... 2 Installation... 3 Operation... 4 Maintenance... 4 Repair... 5 Troubleshooting...

More information

Vickers. Overhaul Manual. Vane Pumps. Small and Large Series Combination Pumps VC(K)(S)-**-(*)*D*-6(1) VC(K)(S)-**-(*)-*-*D*-5(1)

Vickers. Overhaul Manual. Vane Pumps. Small and Large Series Combination Pumps VC(K)(S)-**-(*)*D*-6(1) VC(K)(S)-**-(*)-*-*D*-5(1) Overhaul Manual Vickers Vane Pumps Small and Large Series Combination Pumps VC(K)(S)-**-(*)*D*-6(1) VC(K)(S)-**-(*)-*-*D*-5(1) Revised 12/1/86 I-3150-S Table of Contents Section I. Introduction................................................................................

More information

BRAKE SYSTEM Return To Main Table of Contents

BRAKE SYSTEM Return To Main Table of Contents BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...

More information

1" COMBINED DIRT COLLECTOR & DYNABALL TM CUT-OUT COCK PORTION

1 COMBINED DIRT COLLECTOR & DYNABALL TM CUT-OUT COCK PORTION 1" COMBINED DIRT COLLECTOR & DYNABALL TM CUT-OUT COCK PORTION Part No. 577071 IMPORTANT: This catalog is published as an aid in identifying the detail parts that make up this complete device. Refer to

More information

CARBURETOR. Preliminary Check. Removal of DuraForce Carburetor

CARBURETOR. Preliminary Check. Removal of DuraForce Carburetor Fuel Leaks From Carburetor (Leaking starts after running, stops after shutdown) Note: This condition which does NOT drain the fuel tank is called spit-back. Possible Causes Engine RPM out of proper range

More information

Air Trap TATSU2. Copyright 2013 by TLV CO., LTD. All rights reserved ISO 9001/ ISO M-02 (TATSU2) 7 August 2013.

Air Trap TATSU2. Copyright 2013 by TLV CO., LTD. All rights reserved ISO 9001/ ISO M-02 (TATSU2) 7 August 2013. 172-65177M-02 (TATSU2) 7 August 2013 ISO 9001/ ISO 14001 Manufacturer Kakogawa, Japan is approved by LRQA LTD. to ISO 9001/14001 Air Trap TATSU2 Copyright 2013 by TLV CO., LTD. All rights reserved 1 Contents

More information

Installation, Operation, and Maintenance Manual

Installation, Operation, and Maintenance Manual Installation, Operation, and Maintenance Manual API 6D Piston Check Valve - IOM: Installation, Operation and Maintenance Manual 1/16 Table of Contents 1 INTRODUCTION... 3 1.1 SCOPE... 3 1.2 DISCLAIMER...

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 11 01-14 1 11 01-14 SUBJECT DATE DD15 and DD16 Cylinder Head November 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081 DDC-SVC-MAN-0181 DDC-SVC-MAN-S181

More information

D-1-A TRIPLE VALVE, PC. NO

D-1-A TRIPLE VALVE, PC. NO D-1-A TRIPLE VALVE, PC. NO. 577893 MARCH, 1985 Supersedes issue dated July, 1984 NOTE: The following description and operation is based on this device and its components being new or this device and its

More information

Technical Data P3 PISTON POWER PUMP NON-ELECTRIC CONDENSATE PUMP SD 9952B

Technical Data P3 PISTON POWER PUMP NON-ELECTRIC CONDENSATE PUMP SD 9952B Technical Data SD 9952B SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NEW YORK, 12586-2035 P3 PISTON POWER PUMP NON-ELECTRIC CONDENSATE PUMP Pressures To 250 PSIG (20.7 barg) Temperatures

More information

SM64155 Maintenance & Repair Manual

SM64155 Maintenance & Repair Manual SM64155 September 2011 Applicable addition manuals: Aerospace Group Conveyance Systems Division Carter Brand SM61429 Nozzle SM64349 Nozzle SM64201 Nozzle Maintenance & Repair Manual Continuity Dry Break

More information

Spring Brake Application

Spring Brake Application Technical Tip Maxibrake I Series Spring Brakes Disassembly, Inspections and Reconditioning Instructions Maxibrake I Series spring brake products are mechanical devices and are subject to wear after extended

More information

Installation Operation Maintenance. LSSN Butterfly Valve AGA Approved 50MM - 150MM. QAD#IM6055.REVA

Installation Operation Maintenance. LSSN Butterfly Valve AGA Approved 50MM - 150MM.  QAD#IM6055.REVA LSSN Butterfly Valve Installation Operation Maintenance Licence Number: 5326 www.challengervalves.com.au 1 Index 1. INTRODUCTION 1.1 Design Features 3 1.2 Flange and Pipe Compatibility 4 1.3 Operating

More information

T1-Titanium Non-HVLP Spray Gun

T1-Titanium Non-HVLP Spray Gun T1-Titanium Non-HVLP Spray Gun THE SPRAY GUN PEOPLE FOR PRODUCT INFORMATION CALL: 1-800-742-7731 Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.

More information

COVER. Bendix ATR-6 Antilock. Traction Relay Valves DELIVERY PORTS (6) FIGURE 1 - BENDIX ATR-6 (AND ATR-3 ) ANTILOCK TRACTION RELAY VALVES

COVER. Bendix ATR-6 Antilock. Traction Relay Valves DELIVERY PORTS (6) FIGURE 1 - BENDIX ATR-6 (AND ATR-3 ) ANTILOCK TRACTION RELAY VALVES SD-13-4861 Bendix ATR-6 and ATR-3 Antilock Traction Relay Valves 2 PIN SOLENOID CONNECTOR Bendix ATR-3 Antilock Traction Relay Valves CONTROL SOLENOID CONTROL PORT COVER Bendix ATR-6 Antilock Traction

More information

CLUTCH 6-1 CLUTCH CONTENTS

CLUTCH 6-1 CLUTCH CONTENTS Z CLUTCH 6-1 CLUTCH CONTENTS page page CLUTCH DIAGNOSIS... 2 CLUTCH SERVICE... 9 CLUTCH COMPONENTS MECHANICAL COMPONENTS The clutch mechanism in Grand Cherokee models with manual transmission consists

More information

NILFISK BA 500 Service Manual

NILFISK BA 500 Service Manual NILFISK BA 500 Service Manual Model 66324400 12/94 Form Number 043023 TABLE OF CONTENTS Batteries...21 Brush Drive Belt Adjustment Or Replacement...7 Brush Drive Motor - Carbon brush Inspection... 8 Brush

More information

DP5 Pump. 5:1, Air-operated, Heavy Duty, Oil. General. Operation. Technical Data. Installation R1 09/10

DP5 Pump. 5:1, Air-operated, Heavy Duty, Oil. General. Operation. Technical Data. Installation R1 09/10 DP5 Pump 5:1, Air-operated, Heavy Duty, Oil General The DP5 Pump is a compressed air-operated reciprocating piston medium pressure pump. These pumps are suitable for distribution of all types of light

More information

Technical Manual MSI Hydraulic Adjustable Choke

Technical Manual MSI Hydraulic Adjustable Choke Technical Manual MSI Hydraulic Adjustable Choke MSI A Division of Dixie Iron Works, Ltd. 300 W. Main St. Alice, TX 78332 www.diwmsi.com (800) 242-0059 Revision A TABLE OF CONTENTS SECTION 1 WARNINGS...

More information

MOTORCYCLE DIVISION 4-STROKE BULLETIN NO. GS/GSX/GSX-R - 97 REVISED DATE: 9/2/98

MOTORCYCLE DIVISION 4-STROKE BULLETIN NO. GS/GSX/GSX-R - 97 REVISED DATE: 9/2/98 MOTORCYCLE DIVISION 4-STROKE BULLETIN NO. GS/GSX/GSX-R - 97 REVISED DATE: 9/2/98 MODEL: SUBJECT: REFERENCE: GSX-R750W FUEL HOSE DISCONNECTED FROM FUEL PUMP NEW FUEL PIPE SET (PN 15310-33E50) SERVICE MANUAL

More information

BLACKMER PISTON AIR/RELIEF VALVE (w/o spring) CONVERSION KIT SAFETY DATA. For Pump Models: TXH3C, TXH3B, TXH3A, TXD2.5A, TXD1225A

BLACKMER PISTON AIR/RELIEF VALVE (w/o spring) CONVERSION KIT SAFETY DATA. For Pump Models: TXH3C, TXH3B, TXH3A, TXD2.5A, TXD1225A BLACKMER PISTON AIR/RELIEF VALVE (w/o spring) CONVERSION KIT INSTALLATION OPERATION & MAINTENANCE INSTRUCTIONS WITH PARTS LIST For Pump Models: TXH3C, TXH3B, TXH3A, TXD2.5A, TXD1225A 964608 Page 1 of 8

More information

OPERATING INSTRUCTIONS & SERVICE MANUAL BLUE MAX II HYDROSTATIC TEST PUMP

OPERATING INSTRUCTIONS & SERVICE MANUAL BLUE MAX II HYDROSTATIC TEST PUMP PAGE 1 OF 10 OPERATING INSTRUCTIONS & SERVICE MANUAL BLUE MAX II HYDROSTATIC TEST PUMP EFFICIENT, EASY OPERATION Air operated pump Wide range of pressures and volumes Easy to operate controls Output pressure

More information

HIGH PRESSURE CONTROL VALVE PISTON BALANCED

HIGH PRESSURE CONTROL VALVE PISTON BALANCED PISTON BALANCED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to be

More information

CARTRIDGE FILTER SYSTEMS OWNER S MANUAL

CARTRIDGE FILTER SYSTEMS OWNER S MANUAL CARTRIDGE FILTER SYSTEMS OWNER S MANUAL Installation Operation Parts Designed, Engineered & Manufactured in the USA. 2017 Waterway Plastics 2200 East Sturgis Road, Oxnard CA 93030 Phone 805.981.0262 Fax

More information

MULTIPOSITION AIR CYLINDER

MULTIPOSITION AIR CYLINDER MULTIPOSITION AIR CYLINDER CAST ALUMINUM FOUR-POSITION - ALL AIR SERVICE INFORMATION MOUNTING! Devices should be mounted and positioned in such a manner that they cannot be accidentally operated. INSTALLATION

More information

Parking brake Mechanical brake acting on rear wheels

Parking brake Mechanical brake acting on rear wheels 11 Brake System 11.1 General SPECIFICATIONS EJTC0010 Master cylinder Type Tandem type I.D. mm(in.) 20.64 mm (0.813 in.) Fluid level warning sensor Provided Brake booster Type Vacuum Boosting ratio 4.0

More information

Hydraulic Hand Crimping Tool, PN

Hydraulic Hand Crimping Tool, PN Hydraulic Hand Crimping Tool, PN 59974-1 Instruction Sheet 408-6757 19 JUN 17 Rev G PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand

More information

1. General Description

1. General Description General Description 1. General Description A: SPECIFICATION Front disc brake Rear disc brake Master cylinder Brake booster Brake line Model Other models WRX MT WRX AT STi Size 15 inch type 16 inch type

More information

WARNING Carefully Read These Instructions Before Use

WARNING Carefully Read These Instructions Before Use DO NOT RETURN THIS SPRAYER TO STORE Call: 1-800-950-4458 Backpack Sprayer Use and Care Manual Manufactured for Northern Tool + Equipment Co., Inc. WARNING Carefully Read These Instructions Before Use Model

More information

Free Float Air Trap JA3 JAF3 / JA5 JAF5 JA7 / JA7.2 / JA7.5 / JA8

Free Float Air Trap JA3 JAF3 / JA5 JAF5 JA7 / JA7.2 / JA7.5 / JA8 172-65144MA-05 (JA Series) 29 July 2013 ISO 9001/ ISO 14001 Manufacturer Kakogawa, Japan is approved by LRQA LTD. to ISO 9001/14001 Free Float Air Trap JA3 JAF3 / JA5 JAF5 JA7 / JA7.2 / JA7.5 / JA8 Copyright

More information

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388). TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all

More information

ENGINE LUBRICATION SYSTEM

ENGINE LUBRICATION SYSTEM B ENGINE SECTION LU A ENGINE LUBRICATION SYSTEM LU C D CONTENTS E QR25DE PRECAUTIONS... 2 Precautions for Liquid Gasket... 2 REMOVAL OF LIQUID GASKET SEALING... 2 LIQUID GASKET APPLICATION PROCEDURE...

More information

Air-Assist Service Jack Max. Capacity: 10 Tons

Air-Assist Service Jack Max. Capacity: 10 Tons Form No. 565786 Parts List & Operating Instructions for: 1511B Air-Assist Service Jack Max. Capacity: 10 Tons 109 67 66 68 77 69 70 78 95 94 107 106 108 26 71 72 72 93 X L 65 75 92 91 90 89 88 87 86 85

More information

Section 10 Chapter 17

Section 10 Chapter 17 Section 10 Chapter 17 24 Valve, 8.3 Liter Engine Air Intake System Note: All coding used in the 8.3 Liter and 9 Liter engine manuals are Cummins engine codes. These engine codes have no meaning to New

More information

DEAD ENGINE FIXTURE PORTION

DEAD ENGINE FIXTURE PORTION V 4243-1 Operation & Maintance Information DEAD ENGINE FIXTURE PORTION "U-1-65-8" Dead Engine Fixture, PART NO. 653968 "U-1-40-8" Dead Engine Fixture, PART NO. 569299 AUGUST, 2000 Supersedes issue dated

More information

TECHNICAL BULLETIN. Yoke Removal and Installation Procedure for Meritor Drive Axles. Remove the Yoke and Pinion Seal WARNING CAUTION CAUTION.

TECHNICAL BULLETIN. Yoke Removal and Installation Procedure for Meritor Drive Axles. Remove the Yoke and Pinion Seal WARNING CAUTION CAUTION. Issued 11-99 TECHNICAL BULLETIN Yoke Removal and Installation Procedure for Meritor Drive Axles Remove the Yoke and Pinion Seal Figure 1 WARNING Park the vehicle on a level surface. Block the wheels to

More information

Troubleshooting guide for poor acceleration, black smoke, and flash code 39, SID 147, FMI 7 or 2

Troubleshooting guide for poor acceleration, black smoke, and flash code 39, SID 147, FMI 7 or 2 No.: 09 TS-17Rev2 November 25, 2009 TO: FROM: Service Locations Technical Support Development SUBJECT: EPA04 DDEC V Series 60 Engines Turbocharger Performance Diagnostic Checklist NOTE: This document supersedes

More information

Wastewater Air Release Valve Models 48A, 49A

Wastewater Air Release Valve Models 48A, 49A Manual No. WWAR-OM1-2 Wastewater Air Release Valve Models 48A, 49A Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF OPERATION... 1 INSTALLATION...

More information

INSTALLATION, OPERATION & MAINTENANCE GUIDE

INSTALLATION, OPERATION & MAINTENANCE GUIDE INSTALLATION, OPERATION & MAINTENANCE GUIDE SINGLE CARTRIDGE SEAL INTERNATIONAL BRAZIL SOUTHERN USA HEADQUARTERS REPAIR & SERVICE 1 Jackson Street Rua Javaés, 441/443 1719 South Sonny Avenue Essex Junction,

More information