Piping technology copper/gunmetal
|
|
|
- Gervase Brooks
- 5 years ago
- Views:
Transcription
1 model no. page model no. page model no. page model no. page model no. page Profipress with SC-Contur Piping technology copper/gunmetal 1 ZM_A1_int_en_ _083425_5.pdf :24:38
2 Press connector system with press connectors made of copper and gunmetal tested in acc. with DVGW worksheet W 534 with DVGW test seal and pipes made of copper in acc. with EN 1057 in acc. with DVGW worksheet GW 392. Suitable for drinking water installations in acc. with DIN For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly. Press connectors All sizes with SC-Contur connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage. During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa 0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hpa 0.3 MPa. Marking Green dot on the press connection Sealing elements EPDM, black (ethylene-propylene-dien-monomer rubber); up to 110 C; not resistant against hydrocarbon solvent, chlorinated hydrocarbon solvents, turpentine, petrol carbon does not exceed TOC max = 1.5 mg/l at values between ph = ! Note Limitations of use heating systems Observe VDI 2035 and EN 12828! Certification Profipress (d 12 54) DVGW-Reg.-No. DW-8511BQ0586 Profipress XL (d 64.0) DVGW-Reg.-No. DW-8511BQ0586 Use of press tools The functional safety of the Viega press connector systems is primarily dependent on the perfect condition of the press tools and press machines used. For this reason, for the production of press connections, we recommend the use of Viega press tools and their regular inspection by authorised service points. Technical data Press connectors and components are constantly being optimised. If required, the current Z and installation dimensions can be obtained from the download area of the Viega homepage: viega.com Accessories for use with Easytop fittings, see product area system fittings. 2 Dimensions/Material Standard sizes: d 12; 15; 18; 22; 28; 35; 42; 54 made of copper XL sizes: d 64.0; 66.7; 76.1; 88.9; made of copper XL sizes: d 76.1; 88.9; made of gunmetal Press connectors with threaded connection made of gunmetal: d 12 54; Press connectors with threaded connection made of copper: d 64.0 Areas of application Drinking water Heating/Radiator connection Rainwater Compressed air, noble gases Cooling water pipelines Industry Plant engineering Special applications with EPDM sealing element, factory-fitted stationary sprinkler-extinguishing systems - with VdS certificate G for the sizes DN20-DN50 in connection with copper pipes in acc. with EN 1057 R290 (hard) Solar systems with flat collectors with FKM sealing element (accessories) Solar systems with flat/vacuum collectors District heat suppliers and low pressure steam systems Use of the system for application areas and media other than those described here must be agreed with Viega Service Center. Operating conditions Drinking water installations Operating temperature max. 85 C Operating pressure max. 1.6 MPa Heating installations Operating temperature max. 110 C Operating pressure max. 1.6 MPa Note Observe flow direction! Components made of copper may not be installed upstream from galvanised ferrous materials! Note Limitations of use drinking water (related to the material - except components as fittings, instruments etc.) Pipes made of copper may only be used when the ph value of the drinking water is ph 7.4 or the total volume of organic ZM_A1_int_en_ _083425_5.pdf :24:38
3 Profipress with SC-Contur A1 A1 Index Elbows 4 T-pieces 7 Adapter pieces/adapter elbows 13 Couplings 19 Reductions 21 Screw fittings 23 Caps, plugs 26 Flanges 27 Wall plates 29 Wall lead-ins 33 Compensators 33 Gunmetal ball valves 34 Free-flow valves 35 Concealed free-flow valves, concealed straight seat valves 35 Manifolds, cross pieces 36 Radiator connections 37 Skirting board radiator connection pieces 40 GTIN-Code (Global Trade Item Number, previously EAN-Code) The GTIN-Code composed out of the constant manufacturer number and a six-digit article code - in this example The exchange of the last six digits against the article code shows the GTIN-Code. 3 ZM_A1_int_en_ _083425_5.pdf :24:38
4 ELBOWS Profipress Elbow 90 Model 2416 article d L Z L* Z* L* = length of the previous version Z* = previous version Profipress XL Elbow 90 Model 2416XL article d Z L Sanpress XL Elbow 90 Model 2216XL article d Z L Z* L* Z* = previous version L* = length of the previous version Profipress Elbow 90 Model article d Z L1 L2 Z* L1* L2* Z* = previous version L* = length of the previous version 4 ZM_A1_int_en_ _083425_5.pdf :24:40
5 Profipress with SC-Contur A1 A1 Profipress XL Elbow 90 Model XL article d Z L1 L Sanpress XL Elbow 90 Model XL article d Z L1 L2 Z* L1* L2* Z* = previous version L* = length of the previous version Profipress Elbow 45 Model 2426 article d Z L Z* L* Z* = previous version L* = length of the previous version Profipress XL Elbow 45 Model 2426XL article d Z L ZM_A1_int_en_ _083425_5.pdf :24:41
6 Sanpress XL Elbow 45 Model 2226XL article d Z L Profipress Elbow 45 Model article d Z L1 L2 Z* L1* L2* Z* = previous version L* = length of the previous version Profipress XL Elbow 45 Model XL article d Z L1 L Sanpress XL Elbow 45 Model XL article d Z L1 L ZM_A1_int_en_ _083425_5.pdf :24:43
7 Profipress with SC-Contur A1 A1 Profipress Crossover Model 2427 article d Z L H1 H Profipress Crossover Model 2428 article d Z L H1 H T-PIECES Profipress T-piece Model 2418 article d1 d2 d3 Z1 Z2 Z3 L1 L2 L ZM_A1_int_en_ _083425_5.pdf :24:44
8 Profipress T-piece Model 2418 article d1 d2 d3 Z1 Z2 Z3 L1 L2 L Sanpress T-piece Model 2218 article d1 d2 d3 Z1 Z2 Z3 L1 L2 L ZM_A1_int_en_ _083425_5.pdf :24:45
9 Profipress with SC-Contur A1 A1 Profipress T-piece Model article d1 d2 d3 Z2 Z3 L1 L2 L Profipress XL T-piece Model 2418XL article d1 d2 d3 Z1 Z2 Z3 L1 L2 L ZM_A1_int_en_ _083425_5.pdf :24:46
10 Sanpress XL T-piece Model 2218XL article d1 d2 d3 Z1 Z2 Z3 L1 L2 L Sanpress T-piece Model article d1 R d2 Z1 Z3 L1 L2 L ¾ ¾ ¾ ¾ ¾ ¾ ¼ ZM_A1_int_en_ _083425_5.pdf :24:47
11 Profipress with SC-Contur A1 A1 Sanpress T-piece Model article d1 Rp d2 Z1 Z2 Z3 L1 L2 L3 SS Z1* Z2* Z3* L1* L2* L3* ½ ⅜ ½ ½ ½ ¾ ½ ¾ ½ ½ ½ Z* = Z- dimension of the previous version L* = length of the previous version Sanpress T-piece, G¼, with plug-in end Model article d1 G d2 Z1 Z2 L1 L2 L ¼ ¼ ¼ ¼ ¼ ¼ ¼ ZM_A1_int_en_ _083425_5.pdf :24:48
12 Profipress XL T-piece Model XL article d1 d2 Rp Z1 Z2 Z3 L1 L2 L3 SS ¾ ¾ ¾ ¾ Sanpress XL T-piece Model XL article d1 Rp d2 Z1 Z2 Z3 L1 L2 L3 SS ¾ ¾ ¾ ZM_A1_int_en_ _083425_5.pdf :24:49
13 Profipress with SC-Contur A1 A1 ADAPTER PIECES/ADAPTER ELBOWS Sanpress Adapter Model 2211 article d R Z L SS Z* L* SS* ⅜ ½ ⅜ ½ ⅜ ½ ¾ ½ ¾ ½ ¾ ½ ¾ ¾ ¼ ¼ ½ ¼ ½ ½ Z* = previous version L* = length of the previous version SS* = previous version (spanner size) Sanpress Adapter Model article d G Z L SS ½ Profipress XL Adapter Model 2411XL article d R Z L SS ½ ½ ½ Sanpress XL Adapter Model 2211XL article d R Z L ½ ZM_A1_int_en_ _083425_5.pdf :24:50
14 Sanpress Adapter Model 2212 article d Rp Z L SS ⅜ ½ ½ ⅜ ½ ¾ ½ ½ ¾ ½ ¾ ½ ¾ ¼ ¾ ¼ ¼ ½ ½ Profipress XL Adapter Model 2412XL article d Rp Z L SS ½ ½ Sanpress Adapter Model article d Rp Z L H ½ ½ ½ Sanpress Adapter Model article d Rp Z L H * 18 ½ * = Discontinued, limited availability 14 ZM_A1_int_en_ _083425_5.pdf :24:51
15 Profipress with SC-Contur A1 A1 Sanpress Adapter Model article DN d Z L1 L2 SS1 SS SS = Spanner size SS = spanner size Sanpress Adapter Model 2213 article d1 d2 L Z SS1 SS * * SS = Spanner size SS = spanner size * = Discontinued, limited availability Sanfix P Adapter Model 2213P article d1 d2 L Z * * = Discontinued, limited availability Profipress Adapter Model P article d1 d2 Z L Raxofix Adapter Model 5313P article d1 d2 Z L ZM_A1_int_en_ _083425_5.pdf :24:52
16 Sanfix P Plug-in piece Model 2113 article d1 d2 Z L Raxofix Plug-in piece Model 5313 article d1 d2 Z L Sanpress Plug-in piece Model article d R L SS ½ ½ ½ ¾ ½ ¾ ¼ ½ Sanpress Plug-in piece Model article d Rp Z L SS ½ ½ ½ ¾ ½ ¾ ¾ ¼ ½ ZM_A1_int_en_ _083425_5.pdf :24:53
17 Profipress with SC-Contur A1 A1 Sanpress Adapter elbow 90 Model 2214 article d R Z L1 L2 SS Z* L1* L2* ⅜ ½ ½ ⅜ ½ ¾ ½ ½ ¾ ¾ ¼ ½ Z* = previous version L* = length of the previous version Sanpress Adapter elbow 90 Model article d R Z L1 L ½ ZM_A1_int_en_ _083425_5.pdf :24:54
18 Sanpress Adapter elbow 90 Model article d Rp Z1 Z2 L1 L2 Z1* Z2* L1* L2* ⅜ ½ ½ ⅜ ½ ¾ ½ ½ ¾ ½ ¾ ½ ¾ ¼ ½ Z* = Z- dimension of the previous version L* = length of the previous version Sanpress Plug-in elbow 90 Model article d Rp Z L1 L ½ ZM_A1_int_en_ _083425_5.pdf :24:55
19 Profipress with SC-Contur A1 A1 COUPLINGS Profipress Coupling Model 2415 article d Z L Profipress XL Coupling Model 2415XL article d Z L Sanpress XL Coupling Model 2215XL article d Z L Profipress Sliding coupling Model article d L INDmin INDmin = insertion depth minimum Profipress XL Sliding coupling Model XL article d L INDmin INDmin = insertion depth minimum 19 ZM_A1_int_en_ _083425_5.pdf :24:56
20 Sanpress XL Sliding coupling Model XL article d L INDmin INDmin = insertion depth minimum Sanpress Sliding coupling Model article d L INDmin INDmin = insertion depth minimum Sanpress Sliding coupling Model article d Z L INDmin INDmin = insertion depth minimum Sanpress Coupling Model article d Z L ) Press connection d10 should be carried out with a size 12 press jaw! 20 ZM_A1_int_en_ _083425_5.pdf :24:57
21 Profipress with SC-Contur A1 A1 REDUCTIONS Profipress Reducer Model article d1 d2 Z L Profipress XL Reducer Model XL article d1 d2 Z L Sanpress Reducer Model article d1 d2 Z L Z* L* Z* = previous version L* = length of the previous version 21 ZM_A1_int_en_ _083425_5.pdf :24:57
22 Sanpress Reducer Model NC article d1 d2 Z L ) Press connection d14 should be carried out with a size 15 press jaw! 2) Press connection d16 should be carried out with a size 18 press jaw! Sanpress XL Reducer Model XL article d1 d2 Z L Profipress Reducing coupling Model article d1 d2 Z L Profipress Reducing elbow 90 Model article d1 d2 Z L1 L ZM_A1_int_en_ _083425_5.pdf :24:58
23 Profipress with SC-Contur A1 A1 Profipress Reducing elbow 45 Model article d1 d2 Z L1 L * * = Discontinued, limited availability SCREW FITTINGS Sanpress Screw fitting Model 2260 article d Z L SS1 SS SS = Spanner size SS = spanner size Sanpress Adapter union Model 2262 article d Rp Z L SS1 SS ½ ½ ¾ ½ ¾ ¾ ¾ ¼ ½ SS = Spanner size SS = spanner size 23 ZM_A1_int_en_ _083425_5.pdf :24:59
24 Sanpress Adapter union Model 2265 article d R Z L SS1 SS ⅜ ½ ½ ¾ ½ ¾ ½ ¾ ¾ ¼ ½ SS = Spanner size SS = spanner size Sanpress Adapter union 90 Model 2255 article d Rp Z1 Z2 L1 L2 SS1 SS ½ ½ ½ ¾ ¾ ¼ ½ SS = Spanner size SS = spanner size Sanpress Connection screw fitting Model 2263 article VdS d G Z L1 L2 SS ⅜ ½ ¾ ⅜ ½ ¾ ⅜ ½ ¾ ¼ ½ ¾ ¾ ¾ ¼ ½ ¼ ½ ½ ¾ ¼ ZM_A1_int_en_ _083425_5.pdf :25:01
25 Profipress with SC-Contur A1 A1 Sanpress Connection screw fitting Model 2263 article VdS d G Z L1 L2 SS ⅜ ½ ¾ VdS = VdS certification Sanpress XL Connection screw fitting Model 2263XL article d G Z L1 L2 SS ½ Sanpress Connection screw fitting Model 2264 article d G Z L1 L2 SS ¾ ¾ ¼ ½ ¾ ⅜ Sanpress Insulating union Model 2267 article d Rp Z L SS1 SS ½ ¾ ½ ¾ ¾ ¼ ½ SS = Spanner size SS = spanner size 25 ZM_A1_int_en_ _083425_5.pdf :25:02
26 CAPS, PLUGS Profipress Cap Model 2456 article d Z L Profipress XL Cap Model 2456XL article d Rp Z L1 L2 SS ¾ ¾ ¾ ¾ Sanpress XL Cap Model 2256XL article d Rp Z L ¾ ¾ ¾ Profipress Plug Model 2457 article d L ZM_A1_int_en_ _083425_5.pdf :25:03
27 Profipress with SC-Contur A1 A1 Forcing plug - brass Model 2269 article d L Ø Ø = diameter FLANGES Sanpress Flange adapter Model article DN d Z L W1 W2 Ø1 Ø2 k n Ø = diameter k = bolt circle diameter n = number of holes 27 ZM_A1_int_en_ _083425_5.pdf :25:04
28 Profipress XL Flange adapter Model XL article DN d Z L W1 W2 Ø1 k Ø2 n Ø = diameter k = bolt circle diameter Ø = diameter n = number of holes Sanpress XL Flange adapter Model XL article DN d Z L W1 W2 Ø1 Ø2 k n Ø = diameter k = bolt circle diameter n = number of holes 28 ZM_A1_int_en_ _083425_5.pdf :25:05
29 Profipress with SC-Contur A1 A1 Sanpress XL Flange, PN 16 Model XL article DN Rp Ø1 L W1 W2 Ø2 k n ½ Ø = diameter k = bolt circle diameter n = number of holes WALL PLATES Sanpress Wall plate Model 2225 article d Rp L Z1 Z2 L1 L2 L3 L ½ ZM_A1_int_en_ _083425_5.pdf :25:06
30 Sanpress Wall plate Model article d Rp Z1 Z2 L1 L2 L3 L4 Z1* Z2* L1* L2* L3* L4* ½ ½ ½ ½ ½ ¾ ½ ¾ Z* = Z- dimension of the previous version L* = length of the previous version Sanpress Wall plate Model article d Rp Z1 Z2 L1 L2 L3 L ½ Sanpress Double wall plate Model article d1 Rp d2 Z1 Z2 Z3 L1 L2 L3 L ½ ½ ½ Sanpress Wall plate T-piece Model article d1 Rp d2 Z1 Z2 L1 L2 L ½ ½ ZM_A1_int_en_ _083425_5.pdf :25:07
31 Profipress with SC-Contur A1 A1 Press-in nozzle Model article d Z L Mounting bracket - galvanised steel Model article DG L1 L2 L3 L4 L5 L6 L7 M /100/ DG = depth gauge M = thread type Mounting bracket - galvanised steel Model article DG L1 L2 L3 L4 L5 M DG = depth gauge M = thread type Mounting bracket - galvanised steel Model article L1 L2 L3 L4 L5 M M = thread type 31 ZM_A1_int_en_ _083425_5.pdf :25:08
32 Sanpress Mounting unit Model article d Rp DG Z1 Z2 L1 L2 L3 L4 L5 L ½ DG = depth gauge Sanpress Mounting unit Model article d Rp DG Z1 Z2 L1 L2 L3 L4 L5 L ½ DG = depth gauge Sanpress Mounting unit Model article d1 Rp d2 Z1 Z2 L1 L2 L3 L4 L5 L ¾ Connection elbow 90 Model article Rp Z1 Z2 L1 L2 L3 M ½ ¾ M = thread type 1) gunmetal 2) brass 32 ZM_A1_int_en_ _083425_5.pdf :25:09
33 Profipress with SC-Contur A1 A1 WALL LEAD-INS Sanpress Wall lead-in Model article d Rp G L Z1 Z2 L1 L2 L ½ ¾ ½ ¾ ½ ¾ ½ ¾ Sanpress Wall lead-in Model article d Rp G L Z1 Z2 L1 L ½ ¾ Mounting set Model article G SS D ¾ D = external diameter COMPENSATORS Compensator Model 2251 article d Z L Ø Ø = diameter 33 ZM_A1_int_en_ _083425_5.pdf :25:10
34 GUNMETAL BALL VALVES Easytop Ball valve Model 2270 article DN d Z1 Z2 L1 L2 L3 H1 H ) Discontinued, limited availability Easytop Ball valve Model article DN d Rp Z1 Z2 L1 L2 L3 H1 H ½ ½ ¾ ¼ ½ ) Discontinued, limited availability Easytop Ball valve Model article DN d Z1 Z2 L1 L2 L3 H1 H ZM_A1_int_en_ _083425_5.pdf :25:11
35 Profipress with SC-Contur A1 A1 FREE-FLOW VALVES Easytop Free-flow valve Model 2242 article d Z L H1 H2 Ø Ø = diameter 1) Discontinued, limited availability CONCEALED FREE-FLOW VALVES, CONCEALED STRAIGHT SEAT VALVES Easytop Concealed free-flow valve Model 2240 article d ID Z L H1 H2 ID Ø1 Ø ID = installation depth Ø = diameter 1) Discontinued, limited availability Easytop Concealed straight seat valve Model 2235 article DN d ID Z L H1 H2 Ø ID = installation depth Ø = diameter 1) Discontinued, limited availability 35 ZM_A1_int_en_ _083425_5.pdf :25:12
36 MANIFOLDS, CROSS PIECES Sanpress Screed manifold Model 2252 article d1 d2 d3 Z1 Z2 L1 L2 L3 L4 L ) Press connection d10 should be carried out with a size 12 press jaw! Sanpress Cross T-piece Model article d1 d2 Z1 Z2 Z3 Z4 Z5 L1 L2 L3 L4 L5 L6 L Sanpress Cross piece Model 2244 article d1 d2 INDmin Z L1 L INDmin = insertion depth minimum Sanpress Cross piece Model 2248 article d1 d2 Z1 Z2 L1 L ZM_A1_int_en_ _083425_5.pdf :25:13
37 Profipress with SC-Contur A1 A1 Sanpress Cross piece 24 Model 2247 article d1 d2 Z1 Z2 L1 L RADIATOR CONNECTIONS Radiator connection piece - matt nickel-plated brass Model article G DG Z1 L SS ¾ DG = depth gauge Radiator connection piece - matt nickel-plated brass Model article G DG Z1 Z2 L SS ¾ DG = depth gauge Radiator connection piece - matt nickel-plated brass Model article G DG Z1 L SS ¾ DG = depth gauge Radiator connection piece - matt nickel-plated brass Model article G DG Z1 Z2 L SS ¾ DG = depth gauge 37 ZM_A1_int_en_ _083425_5.pdf :25:14
38 Adapter set - brass Model article G1 G2 L SS ½ ¾ Adapter set Model article D L D = external diameter Connection screw fitting - nickel-plated brass Model article d G L SS ¾ ¾ Adapter set - matt nickel-plated brass Model article R G L SS ½ ¾ Adapter set - matt nickel-plated brass Model article G1 G2 Z L SS ¾ ¾ ZM_A1_int_en_ _083425_5.pdf :25:15
39 Profipress with SC-Contur A1 A1 Radiator connection block Model article d Z1 Z2 L1 L2 L3 L4 H1 H Radiator connection block Model article d H Z L1 L2 L3 L4 H1 H Radiator connection set - matt nickel-plated brass Model article d G Z1 Z2 Z3 L ¾ Radiator axial valve - nickel-plated brass Model article d R L1 L ½ Sanpress Return pipe screw fitting Model article d R Z L1 L2 SS ½ Sanpress Return pipe screw fitting Model article d R Z L1 L2 L3 SS ½ ZM_A1_int_en_ _083425_5.pdf :25:16
40 SKIRTING BOARD RADIATOR CONNECTION PIECES Skirting board radiator connection piece Model article Ø Z1 Z2 Z3 Z4 L1 L2 L3 L4 L5 L6 L Ø = diameter Sanpress Plug adapter Model article d Z L Plug adapter Model article Z L Sanpress Radiator connection piece Model article d1 G d2 Z1 Z2 Z3 L1 L2 L3 L4 L ½ ½ Radiator connection set - nickel-plated brass Model article d G L1 L2 L ¾ ZM_A1_int_en_ _083425_5.pdf :25:17
41 Profipress with SC-Contur A1 A1 Connection elbow 90 - stainless steel Model article d L1 L ZM_A1_int_en_ _083425_5.pdf :25:18
42 order code page order code page order code page order code page order code page ZM_A1_int_en_ _083425_5.pdf :25:18
43 order code page order code page order code page order code page order code page ZM_A1_int_en_ _083425_5.pdf :25:18
44 order code page order code page order code page order code page order code page 44 ZM_A1_int_en_ _083425_5.pdf :25:18
45 model no. page model no. page model no. page model no. page model no. page P XL P NC XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL XL P ZM_A1_int_en_ _083425_5.pdf :25:18
Piping technology gunmetal
model no. page model no. page model no. page model no. page model no. page Sanpress with SC-Contur Piping technology gunmetal 1 ZM_G3_int_en_20170106_082446_5.pdf 1 06.01.2017 10:02:32 Press connector
Piping technology stainless steel
model no. page model no. page model no. page model no. page model no. page Sanpress Inox with SC-Contur Piping technology stainless steel 1 ZM_G1_int_en_20170106_082446_5.pdf 1 06.01.2017 10:00:47 Press
Piping technology stainless steel
model no. page model no. page model no. page model no. page model no. page Sanpress Inox G with SC-Contur Piping technology stainless steel 1 ZM_G2_int_en_20170106_082446_5.pdf 1 06.01.2017 10:08:51 Press
Piping technology steel
model no. page model no. page model no. page model no. page model no. page Prestabo with SC-Contur Piping technology steel 1 ZM_F1_int_en_20170109_105948_5.pdf 1 09.01.2017 11:44:43 Press connector systems
Piping technology plastic
model no. page model no. page model no. page model no. page model no. page Viega Smartpress Piping technology plastic 1 ZM_L6_int_en_20170314_131501_5.pdf 1 14.03.2017 15:31:15 Flow-optimised press connector
Piping technology stainless steel
INT 4/ Catalogue 0/0 We reserve the right to effect changes. Sanpress Inox Piping technology stainless steel G Press connector system with press connectors an pipes mae of stainless steel material Nos..440
Take O ff Dimensions. Profipress with SC- Contur. Pipe line systems / Pipe connection technology 12.8 /
A Take O ff Dimensions Pipe line systems / Pipe connection technology Profipress with SC- Contur 2.8 / 202 86529 www.viega.com A Take Off Dimensions Pipe line systems / Pipe connection technology Profipress
Smartloop Connection Set. Instructions for Use from 07/2008. en_int
Smartloop Connection Set Instructions for Use Model Year built: 2276.1 from 07/2008 en_int Smartloop Connection Set 2 from 27 Table of contents Table of contents 1 About these instructions for use 4 1.1
Globo P. Ball valves Pump ball valve made of gunmetal
Globo Ball valves ump ball valve made of gunmetal IMI EIMEIER / Shut-off valves / Globo Globo Globo and Globo -S are used in pump warm water heating systems for direct connection to circulating pumps with
INT 4/15 Catalogue 2015/2016 We reserve the right to effect changes. System press tools. Piping technology
INT 4/5 Catalogue 205/206 We reserve the right to effect changes. Piping technology P For all Viega press systems from d 2 08.0. Viega system press tools can be used with all metallic Viega press systems
Areas of Application of Metallic Installation Systems
Areas of Application of Metallic Installation Systems Information for planning and completion 566263 02.15 / 2016 Areas of application of metallic installation systems Conversion Bar / Pascal.............
4 01 ta l o g u e 2 Ca P R i c e L I S T
Catalogue 2014 The Complete Product Range The compression fittings: Our Gebo Quick the universal compression fittings are available for steel pipes of 1/2" to 2" diameter, for black steel pipes of 20 mm
NiroSan -Press. Press systems from high-grade stainless steel Made in Germany
NiroSan -Press pressable with V, M and SA-profile Press systems from high-grade stainless steel Made in Germany NiroSan -Press system fittings and NiroSan system pipes in stainless steel with tool compatibility,
Index. Contact General information SANHA Group Application overview Terms and Conditions of Sale PIPING SYSTEMS
Index Contact General information SANHA Group Application overview Terms and Conditions of Sale IV V VI X XIII PIPING SYSTEMS stainless steel NiroSan - (Series 9000) 1 NiroSan Gas - (Series 17000) 2 NiroSan
SINGLE-ECCENTRIC BUTTERFLY VALVES TYPE L32.6
Application Single-eccentric butterfly valves are industrial valves, which are designed to fully open or close a passage of the working medium flowing through a pipeline. They can also be used for flow-control
PRESS-FIT SYSTEM FOR SPRINKLER CONNECT WITH CONFIDENCE
PRESS-FIT SYSTEM FOR SPRINKLER CONNECT WITH CONFIDENCE CONNECT WITH CONFIDENCE With a wealth of expertise and the broadest range of solutions and systems on the market, Pegler Yorkshire s Connect products
New! NiroTherm. Premium solution for corrosive environments. exclusively from SANHA
NiroTherm New! = Tool Compatibility + Push & Stay + Leak Path Feature exclusively from SANHA Premium solution for corrosive environments Optimal for heating, cooling and compressed air installations high
Installation and operating instructions KEMPER Free-flow combination anti-pollution check valve EA Figure 145/146
Installation and operating instructions KEMPER Free-flow combination anti-pollution check valve EA Figure 145/146 Photo 1: Figure 145/146 0G Photo 2: Figure 145 1G 1. Application range The KEMPER Free-flow
Rubber-steel gaskets. Gasket profiles WG2 WG2P WL-HT KNG. Rubber-steel gaskets
Rubber-steel gaskets have amassed a wide range of applications in sealing technology. Wherever the secure sealing of media with an exceptionally low leak rate, as well as low bolt loads at relatively low
SINGLE-ECCENTRIC BUTTERFLY VALVES TYPE L32.6
Application Single-eccentric butterfly valves are industrial valves, which are designed to fully open or close a passage of the working medium flowing through a pipeline. They can also be used for flow-control
DOUBLE-ECCENTRIC BUTTERFLY VALVES TYPE L32.7
Application Double-eccentric butterfly valves are industrial valves, which are designed to fully open or close the passage of the working medium flowing through a pipeline. They can also be used for flow-control
SUITABLE FOR. Warm water EXAMPLES OF USE. Type approval ACS. Type approval WRAS (up to 85 C) Requirements. DIN DVGW guidelines DIN EN 1567 DIN 1988
Pressure reducing valves Series 682 9.4 682 Pressure reducing valves made of gunmetal with flange connections SUITABLE FOR Liquids neutral and non-neutral Air, gases and vapours neutral and non-neutral
Self-operated Temperature Regulators Type 1u Temperature Regulator
Self-operated Temperature Regulators Type 1u Temperature Regulator Version according to ANSI Application Temperature regulators for cooling plants Control thermostats for set points 1) from 15 to 480 F
W PSC Press DN AS3688 PN-16. W PSC Press DN AS3688 PN-16 COPPER PRESS SYSTEM (WATER) TECHNICAL AND INSTALLATION GUIDE
26126 AS3688 PN-16 W PSC Press 26126 AS3688 PN-16 W PSC Press COPPER PRESS SYSTEM () TECHNICAL AND INSTALLATION GUIDE Products WE ARE HERE FOR THE LONG RUN AND SO ARE OUR PRODUCTS! At the Plumbers Supplies
DA 50. Differential pressure controllers Adjustable set-point
DA 50 Differential pressure controllers Adjustable set-point IMI TA / Differential pressure controllers / DA 50 DA 50 These differential pressure controllers for heating and cooling systems are particularly
Chibro Press Fit Stainless Steel Pipe and Fittings. Data Sheet
Chibro Press Fit Stainless Steel Pipe and Fittings General Information Data Sheet The Chibro Press Fit Pipe system permits the installation of a metal piping system in a reliable and economic way. The
2/2-way Globe Valve for media up to +180 C, DN
2/2-way Globe Valve for media up to +180 C, DN 10-100 Compact globe valve version Flange, threaded and welded ports as standard Stainless steel 316L valve body vailable with flow direction below and above
Self-operated Temperature Regulators Type 1u Temperature Regulator
Self-operated Temperature Regulators Type 1u Temperature Regulator ANSI version Application Temperature regulators for cooling installations Control thermostats for set points 1) from 15 to 480 F ( 10
Piping technology PE-Xc/Al/ PE-Xc/gunmetal/ PPSU
INT 4/ Catalogue /6 We reerve the right to effect change. Pexfit Pro Piping technology PE-Xc/Al/ PE-Xc/gunmetal/ PPSU Pre connector ytem for rinking water intallation in acc. with DIN 988 an D IN 0930
Self-operated Temperature Regulators Temperature Regulator Type 1u
Self-operated Temperature Regulators Temperature Regulator Type u Application Temperature regulators for cooling installations Control thermostats for set points from 0 to 250 C G ½ to G or DN 5 to DN
4-way Distribution Valve
4-way Distribution Valve for one- and two-pipe systems Product specification sheet Application 4-way distribution valves are used to connect supply and return of a radiator to the corresponding pipes of
2/2 way Angle-Seat Valve for medium up to C, DN15-50
Type 2000 can be combined with 2/2 way Angle-Seat Valve for medium up to + 180 C, DN15-50 High flow rates Very high cycle life Clamp body according to EN ISO 2852, BS 4825 or ASME BPE For process valves
RTL. Floor Heating Controller Return temperature limiter with and without presetting
RTL Floor Heating Controller Return temperature limiter with and without presetting IMI HEIMEIER / Floor Heating Control / RTL RTL Among other things, the return temperature limiter RTL is used to limit
TA-Mini-Fast-Fit. Prefab units Fabricated solutions for small terminal units
TA-Mini-Fast-Fit Prefab units Fabricated solutions for small terminal units IMI TA / Control valves / TA-Mini-Fast-Fit TA-Mini-Fast-Fit Compact pressure independent solution for modulating or on/off control.
SUITABLE FOR. Warm water EXAMPLES OF USE APPROVALS. Type approval ACS. Type approval WRAS (up to 85 C)
Pressure reducing valves Series 482 9.3 482 Pressure reducing valves made of stainless steel with flange connections SUITABLE FOR Liquids neutral and non-neutral Air, gases and vapours neutral and non-neutral
Pressure relief controller for oil V22D28 (PN 16, 25)
Data sheet Pressure relief controller for oil V22D28 (PN 16, 25) Description The controller has a control valve, an actuator with one control diaphragm and a spring for pressure setting. Features: - safe
Butterfly valves PN6, PN10, PN16
4 136 Butterfly valves PN6, PN10, PN16 VKF46... Butterfly valves for fitting between counter-flanges Nominal pressures PN6, PN10, PN16 For fitting between PN6, PN10 or PN16 counter-flanges to ISO 7005
2/2-way Globe Valve for media up to +180 C, DN
2/2-way Globe Valve for media up to +180 C, DN 10-100 Compact globe valve version Flange, threaded and welded ports as standard Stainless steel 316L valve body Available with flow direction below and above
SITRANS F flowmeters. SITRANS F O delta p - Primary differential pressure devices Metering pipe with orifice plate and annular chambers 4/369
and annular chambers Application Suitable for non-corrosive and corrosive gases, vapors and liquids; permissible operating temperature -10 to +00 C. Design Orifice plate with annular chambers consisting
Mikrotherm F. Manual Radiator Valves With presetting
Mikrotherm F Manual Radiator Valves With presetting IMI HEIMEIER / Thermostatic Heads & Radiator Valves / Mikrotherm F Mikrotherm F The Mikrotherm F manual radiator valve is used in warm water pump heating
ANSI version. The valve closes when the differential pressure rises
Self-operated Regulators Series 42 Differential Pressure Regulator with Type 2424/Type 2428 Actuator and Type 2422 Valve Type 42-24 A Type 42-24 B Type 42-28 A Type 42-28 B ANSI version Application For
SUITABLE FOR. Warm water EXAMPLES OF USE APPROVALS. Type approval ACS. Type approval WRAS (up to 85 C)
Pressure reducing valves Series 681 9.2 681 Pressure reducing valves made of gunmetal with threaded connections SUITABLE FOR Liquids neutral and non-neutral Air, gases and vapours neutral and non-neutral
Pipeline Accessories. Rubber Steel gasket Type RSG Type RSG-V Type RFG 4 pipes
Pipeline Accessories Rubber Steel gasket Type RSG Type RSG-V Type RFG 4 pipes Flange Gaskets Type RSG 4 pipes Reg.Nr. NG-5113CQ0574 Trinkwasser KTW/W270 Product Information RSG 4 pipes Rubber-Steel-Flange-Gasket
Instrumentation Products Gauge Valves and Pressure Gauge Accessories
Instrumentation Products Gauge Valves and Pressure Gauge Accessories Introduction Introduction The AS-Schneider Group with its headquarters in Germany is one of the World s Leading Manufacturers of Instrumentation
Flow-compensated temperature controller AVTQ DN 15
Data sheet Flow-compensated temperature controller AVTQ DN 15 Description AVTQ is a self-acting flow-compensated temperature controller primarily for use in district heating systems with plate heat exchangers
PRESS STAINLESS STEEL
PRESS STAINLESS STEEL UP TO 54 MM PRESS-FITTED WITH M OR V PROFILE! SUPERIOR PRICING & QUALITY 20 YEAR WARRANTY 12 MM - 108 MM PRODUCT CATALOGUE UK 015 PRODUCT CATALOGUE Press stainless steel Straight
Valves for building. Y-strainers... page 204 PVC valves Ball valves... page 204 Butterfly valve... page 204 Ball check valve...
Valves for building Ball valves PN25/20... page 194 PN30/20... page 195 PN40/30 - Lead-free brass... page 196 Valve for gas... page 197 Stem extension valves... page 197 3 way valves... page 197 Mini valves...
Application technology, 5th edition. Volume III: Fonterra radiant heating and cooling
Application technology, 5th edition Volume III: Fonterra radiant heating and cooling Regulation components, manifolds and manifold cabinets Regulation components, manifolds and manifold cabinets System
Valves for building. Y-strainers... page 272 PVC valves Ball valves... page 272 Butterfly valves... page 272 Ball check valves...
Valves for building Ball valves PN25/20... page 262 PN30/20...pages 262 to 263 PN40/30 - Lead-free brass... page 264 Valve for gas... page 265 Stem extension valves... page 265 3 way valves... page 265
KFE Ball Valves The Benchmark for Quality and Reliability
Simplex KFE Ball Valves CLIMATE CONTROL SYSTEMS KFE Ball Valves The Benchmark for Quality and Reliability I For heating, domestic water and solar I Ease of installation due to proven design I Convenient
COMPANY PROFILE TABLE OF CONTENT. Our products have been supplied to local and foreign customers for the following industries:
UTTERFLY VALVES TALE OF CONTENT COMPANY PROFILE The company ARMATURY Group a.s. is a leading Czech manufacturer and distributor of industrial valves, fittings and control systems for valves. The annual
2/2-way Quarter-Turn Ball Valve in stainless steel with pneumatic rotary actuator, DN 10-50
2/2-way Quarter-Turn Ball Valve in stainless steel with pneumatic rotary actuator, 10-50 (2652) (2655) 2 or ball valve Pneumatic actuator Compact design Visual position indicator Types 2652/2655 can be
Pressure relief controller AVA (PN 25)
Data sheet Pressure relief controller AVA (PN 25) Description AVA is a self-acting pressure relief controller primarily for use in district heating systems. The controller is normally closed and opens
2 PIECES BALL VALVE PN63
2 PIECES BALL VALVE PN63 Model/Ref: 220 www.lauridsenindustri.com Size : Ends : Min Temperature : Max Temperature : DN 15 to DN 400 Flanges ISO PN10/16-10 C + 120 C Max Pressure : 16 Bars up to DN 200
Push-Fit Transition Coupling for PE-100/PVC-U water pipes up to 16 bar patented
Push-Fit Transition Coupling for PE-100/PVC-U water pipes up to 16 bar patented PE-100 / PVC-U pull-out resistant long type Push-Fit Transition Coupling for PE-100 and PVC-U water pipes up to 16 bar d90
Type 455, 456. Facts. Flanged Safety Relief Valves spring loaded. The-Safety-Valve.com. US Units
Type 455, 456 Flanged Safety Relief Valves spring loaded US Units Facts The-Safety-Valve.com LWN 468.08-E 462.01-D 40 Cap H2 19 Lock nut 18 Adjusting screw 16 Upper spring plate 9 Bonnet 12 Spindle 54
Ball valves and shut off valves
Shut off valves HE Hand slide valves W Ball valves QH, manually actuated Ball valves VAPB, mechanically actuated Ball valves VAPB CR, mechanically actuated, corrosion resistant 2003/10 Subject to change
Product range Solex Technical data and dimensioning. 5 Years
Qualität made in Germany Product range Solex Technical data and dimensioning Quality made in Germany 5 Years Handwerkergarantie m anufacturer s warranty Product range Solex Dimensioning High-Flow system
Products: Composite Hose Metall Hose Bellows, Compensators Swivel Joints Composite Hose. Metall Hose, Bellows and Compensators
Composite Hose Metall Hose Bellows, Compensators Swivel Joints Composite Hose Very flexible and easy to handle hoses for trucks, ships, railroad cars and industrial applications. Available in various designs
3-Port Seat Valves with Male Thread, PN 16
4 463 3-Port Seat Valves with Male Thread, PN 16 VXG41 Use Media Bronze CC491K (Rg5) valve body DN 15DN 50 k vs 1640 m 3 /h Flat sealing connections with external thread G B to ISO 228/1 Sets of ALG 3
GSR - your partner for valve technology. Welcome to the world of valve technology. Your GSR Team
Welcome to the world of valve technology GSR - your partner for valve technology This is the world of solenoid valves, with and without explosion protection, of external medium-controlled valves and motorised
2/2-way Angle-Seat Valve for medium up to +180 C, threaded port connection, DN 15-65
2/2-way Angle-Seat Valve for medium up to +180 C, threaded port connection, DN 15-65 Type 2000 can be combined with High flow rate Long life cycle NC and NO universal s with modular universal accessory
Solenoid valve. Technical data Orifice 1/4 4 Body materials Actuator material Seal material Media Viscosity. Control medium Port connections
/-way Diaphragm Valve with plastic body, pneumatically operated, 1/ 3 with true union 3 with fl ange pplications with aggressive media Flow optimised body with zero dead volume Self draining installation
Thermostatic actuator RAVI - for 2-way valves RAV-/8 (PN 10), VMT-/8 (PN 10), VMA (PN 16)
- for 2-way valves RAV-/8 (PN 10), VMT-/8 (PN 10), VMA (PN 16) Description RAVI is self-acting thermostatic actuator primarily for use for temperature control of small hot water cylinders - either storage
2018/2019 PRODUCT CATALOGUE. Ball valves Heating, piping and industrial fittings 40YEARS
PRODUCT CATALOGUE Ball valves Heating, piping and industrial fittings 2018/2019 40YEARS PERSONAL CONTACTS at WESA-Armaturen GmbH Reception 07181 / 404-0 info@wesa-armaturen.de Sales management Germany
Side channel pumps PN 16 SOH - SOHB. Self-priming centrifugal pumps. Technical description
Side channel pumps PN 16 Self-priming centrifugal pumps SOH - SOHB Technical description Operating data Design Industries Media pumped: Nominal diameter: 1-1 1 /2 Flow rate: 0.3-7.5 m 3 /h Pump head: 5-155
Pressure independent control valve with integrated flow limiter AVQM (PN 16) - return and flow mounting
Data sheet Pressure independent control valve with integrated flow limiter AVQM (PN 16) - return and flow mounting Description Controllers are used together with Danfoss electrical actuators: AMV 0 1)
Supplementary instructions. Mounting accessories, pressure measurement technology. Document ID: 43478
Supplementary instructions Mounting accessories, pressure measurement technology Document ID: 78 Contents Contents About this document.... Function.... Target group.... Symbols used... For your safety....
Item Component Remarks Type 4393 Type ), SA Vulcanized soft seal disc SA L SA L
Available designs materials Materials Item Component Remarks 3 4 1 Base / Inlet body 2 Outlet body Threaded connection Flange connection 2.1 Outlet adaptor Flange connection 2.4 Outlet flange Flange connection
Hydrants. Tab 2, page 1
Hydrants Tab 2, page 1 Hydrants Hydrants Made of ductile cast iron (SGCI) Introduction Hydrants made by Keulahütte GmbH in Krauschwitz are manufactured based on many years of design and development work
2-port and 3-port valves with T-bypass PN 16
4 854 2-port valves 3-port valve with T-bypass CVTIX 2-port and 3-port valves with T-bypass PN 16 VVP45..S VMP45..S ronze CC499K valve body DN 10 and DN 15 k vs 0.63 2.5 m 3 /h Externally threaded connections
2/2-way-Globe Valve with stainless steel design for media up to +180ºC, DN 13-50
2/2-way-Globe Valve with stainless steel design for media up to +180ºC, DN 13-50 High cycle life Flow optimised body in stainless steel 316L Deliverable with fl ow direction below or above seat Clean design
High CATALOG. Efficiency. Pilot Operated Safety Valves Series 810 Pop Action Series 820 Modulate Action. The-Safety-Valve.com
High Efficiency Pilot Operated Safety Valves Series 10 Pop Action Series 20 Modulate Action CATALOG The-Safety-Valve.com Valve finder How to find the right product group High operating to set pressure
MK508MM Series. Back Pressure Regulators Mark 508MM Self-Operated Back Pressure Regulators. Self-Operated Back Pressure Regulators.
MK508MM Series Self-Operated Back Pressure Regulators The MK508MM series are spring loaded, self actuated, direct-operated valves. The Mark 508MM Back Pressure Regulating Valves regulate upstream pressure
SUITABLE FOR. Steam EXAMPLES OF USE APPROVALS. Type approval WRAS. Type approval ACS. Requirements DIN EN ISO PED 2014/68/EU TRD 421
Type test approved safety valves angle-type for industrial applications Series 642 642 Safety valves made of gunmetal, angle-type with threaded or flange connections SUITABLE FOR Liquids neutral and non-neutral
Pressure reduction controllers (PN 25) AVDS - for steam AVD - for water
Data sheet Pressure reduction controllers (PN 25) - for steam AVD - for water Description Main data AVD: DN 15-50 k VS 0,4-25 m 3 /h PN 25 Setting range: 1-5 bar / 3-12 bar Temperature: - Circulation water/glycolic
SH Stainless Steel Piping System
Stainless Steel Piping Systems SH Stainless Steel Piping System 2018 PRICE LIST Industrial Applications Heating Compressed Air Closed Water Circulation Systems ry Fire Water Mains Solar SH system pipes
R o L. BUTTERFLY VALVE of carbon steel with welded ends 313 -series BLUE LINE. Description
of carbon steel 313 -series C ont R o L Description Edition 23-07-2015 The welded butterfly valve 313 is specially designed for district heating and district cooling. It can be used as an on-off or control
SUITABLE FOR EXAMPLES OF USE APPROVALS. Requirements PED 2014/68/EU
Overflow and pressure control valves Series 630 6.10 630 Overflow and pressure control valves made of gunmetal, straightway form with threaded connections externally adjustable SUITABLE FOR Liquids neutral
Direct-operated, Back Pressure Regulating Valve. Features
MK508BPM Series Direct-operated, Back Pressure Regulating Valve The MK508BPM series are spring loaded, self actuated, direct-operated, valves. Pressure relief valves are used to protect the system from
2018 High Performance Check Valves for liquid and gaseous media
2018 High Performance Check Valves for liquid and gaseous media Check valves Catalogue 45 Date: 04/2018 WEH - We Engineer Hightech All rights reserved, WEH GmbH 2018. Unauthorized copies are strictly forbidden
MK508UBS Series. Back Pressure Regulator MK508UBS. Threaded or Flanged Connections Carbon Steel, Stainless Steel & Alloy Construction.
MK508UBS Series Threaded or Flanged Connections Carbon Steel, Stainless Steel & Alloy Construction The MK508UBS Series are spring loaded, direct-operated, pressure relief valves used downstream of pressure
Flow-Through Fitting ARF 215
Flow-Through Fitting ARF 215 Standard Models Model for Pressurized Sensors Latest Product Information: www.knick.de Warranty Defects occurring within 1 year from delivery date shall be remedied free of
2/2-way Angle-Seat Valve for media up to +180 C, threaded port connection, DN 13-65
2/2-way Angle-Seat Valve for media up to +180 C, threaded port connection, DN 13-65 Standard valve body Type 2000 can be combined with Short valve body High flow rate and long life cycle Very high cycle
Table of contents. Chapter 1: Fusiotherm. Chapter 4: climasystem Produktgruppe 20. Chapter 5: aquatherm. Chapter 2: aquatherm SHT.
Table of contents Chapter 1: Fusiotherm 01 Fusiotherm -pipe 04 climatherm-pipe & aquatherm-lilac 07 Accessories 09 Fittings 15 Weld-in saddle 19 Threaded connections and accessories 22 Transition pieces
Flow controller (PN 25) AVQ - return and flow mounting
Data sheet Flow controller (PN 5) - return and flow mounting Description is a self-acting flow controller primarily for use in district heating systems. The controller closes when set max. flow is exceeded.
VALFONTA PRESSURE REGULATOR WITHOUT AUXILIARY ENERGY EXCESS PRESSURE VALVE (PRESSURE RELIEF VALVE) MODEL S1 MAIN CHARACTERISTICS
PRESSURE REGULATOR WITHOUT AUXILIARY ENERGY EXCESS PRESSURE VALVE (PRESSURE RELIEF VALVE) MODEL S1 MAIN CHARACTERISTICS The S1 model is self-operated bellows sealed pressure excess valve. This series of
2/2-way Solenoid Valve for liquids and gases
2/2-way Solenoid Valve for liquids and gases Type 6213EV can be combined with... Coupled spring diaphragm system opened without differential pressure Waterhammer free and low noise HP00 version with increased
3/2-way Solenoid Valve, direct-acting, NC or NO
3/2-way Solenoid Valve, direct-acting, NC or NO Electrical connection cable plug, Form A With or without manual override as standard Threaded port and sub-base s Impulse optional Type 6014 can be combined
Valves and Solutions for the Process Industries
Valves and Solutions for the Process Industries Overview Process Industries 1. Business Unit Process Industries Safety Relief Valves 1.1 This is our business 1.2 Organisation 1.3 Offices and Locations
V Verafix Design Thera Design Edition - Lockshield Valve WITH HIGH QUALITY SURFACE FOR DESIGN RADIATORS
V2480 - Verafix Design Thera Design Edition - Lockshield Valve WITH HIGH QUALITY SURFACE FOR DESIGN RADIATORS PRODUCT DATA Angle Straight Application The Thera Design Edition is particularly styled for
Pressure relief controller AFA / VFG 2(1) (PN 16, 25, 40)
Data sheet Pressure relief controller AFA / VFG 2(1) (PN 16, 25, 40) Description The controller is a self-acting pressure relief controller primarily for use in district heating systems. The controller
Differential-Pressure Flow Meter
Design and application The metering orifice measures and monitors the flow rate of liquids. The user mounts the orifice between flanges or with Rp screwed connections into the conduit. The unimpeded, straight
Differential pressure controller with flow limitation and with integrated control valve (PN 16) AHPBM-F flow mounting, fixed setting
Data sheet Differential pressure controller with flow limitation and with integrated control valve (PN 16) AHPBM-F flow mounting, fixed setting Description The controller has a control valve with adjustable
Regutec F. Return Lockshield Radiator lockshield
Regutec F Return Lockshield Radiator lockshield IMI HEIMEIER / Thermostatic Heads & Radiator Valves / Regutec F Regutec F The Regutec lockshield is used in pumped warm water heating and air conditioning
V2000FS FS type TRV Body FINELY PRESETTABLE RADIATOR VALVE WITH FLUSH POSITION
V2000FS FS type TRV Body FINELY PRESETTABLE RADIATOR VALVE WITH FLUSH POSITION PRODUCT DATA Application 011 Angle to DIN Angle to NF Straight to DIN Straight to NF Thermostatic radiator valve bodies (TRV
Compact. Performance. Safety Relief Valves Series 437 Series 459. The-Safety-Valve.com
Compact Performance Safety Relief Valves Series 437 Series 459 EXTENDED CATALOG The-Safety-Valve.com Valve Finder How to find the right Product Group High operating to set pressure ratio, high backpressure
Pressure Regulator compact 8011
Pressure Regulator compact 8011 GS 3 series 1/2 up to 6 Self operated regulation of inlet and outlet pressures of neutral through to highly aggressive media in process engineering, chemical industries
Manual Presetting Valves LENO MSV-B
Data Sheet Description LENO MSV-B is a new generation of manual valves for balancing flow in heating, cooling and domestic hot water systems. LENO MSV-B is a combined presetting and shut off valve with
Data sheet Pressure independent control valve with integrated flow limiter AVQM (PN 16) - return and flow mounting
Pressure independent control valve with integrated flow limiter AVQM (PN 16) - return and flow mounting Description Controllers are used together with Danfoss electrical actuators: - AMV 150 1) - AMV(E)