RLCP08R- Rear Crossbar
|
|
- Elfreda Black
- 5 years ago
- Views:
Transcription
1 - Rear Crossbar VOLKSWAGEN Caddy Maxi MY11> RENAULT Kangoo Maxi MY13> Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fitment and report any discrepancies. Clean roof mounting points prior to installation. Important Information Maximum carrying capacity: VW Caddy Maxi 100kg. Evenly distributed over all crossbars. Renault Kangoo/ Kangoo Maxi & Nissan Kubistar 80kg. Evenly distributed over all crossbars. Recommendations: It is essential that all bolt connections be checked after driving a short distance when you first install your crossbars. Bolt connections should be checked again at regular intervals (probably once a week is enough, depending on road conditions, usage, loads and distances travelled). You should also check the crossbars each time they are re-fitted. Make sure to fasten your load securely. Ensure all loads are evenly distributed and centre of gravity is kept as low as possible. Use only non-stretch fastening ropes or straps. Caution: The handling characteristics of the vehicle changes when you transport a load on the roof. For safety reasons we recommend you exercise extreme care when transporting wind-resistant loads. Special consideration must be taken into account when cornering and braking. Please remove crossbars when putting vehicle through an automatic car wash. Load ratings: Maximum permissible load for Caddy Maxi is 100kg per pair of crossbars, for Kangoo/Kubistar is 80kg. When crossbars are to be used in off-road conditions, please build a safety factor of 1.5 into this load limit. 66kg for Caddy/Caddy Maxi. 53kg for Kangoo/ Kubistar. Although the crossbars are tested and approved to AS , off-road conditions can be much more rigorous. However, increasing the number of crossbars does not increase the vehicles maximum permissible roof loading. Note for Dealers and Fitters: It is your responsibility to ensure instructions are given to the end user or client. Rhino-Rack 3 Pike Street, Rydalmere, Document No: R137 NSW 2116, Australia. Prepared By: Craig Jones Issue No: 03 (Ph) (02) Authorised By: Chris Murty Issue Date: 31/03/2015 (Fax) (02) These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended. Page 1 of 6
2 ! ü! ü! km/h X 2 x Crossbars = 5kg/11lbs? kg/lbs When these roof racks are to be used on a vehicle that is driven off sealed roads, the manufacturer maximum roof load rating (found in the vehicles User Manual) should be divided by 1.5. Subtract 5kg/11lbs from your maximum carrying capacity to account for the weight of the roof racks. Max: 100kg/220lbs (Urban road) = Max: 66kg/145lbs (Off road) WARNING! Important Load Carrying Instructions With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicle can be damaged if the item transported is rigidly fixed at points on both the cabin and canopy. Instead, rigidly fix to either the cabin roofracks or the canopy roofracks. üyes XNO üyes Page 2 of 6
3 Parts List Item Component Name Qty Part No. 1 M6 x 27mm Security Screw 2 B063 2 M10 Channel Nut 2 N024 3 M6 Spring Washer 2 W004 4 Leg Height Spacer 4 M016 5 M6 x 12.5mm Flat Washer 2 W003 6 RLCPH Leg 2 M559 7 M8 x 25mm Button head bolt 2 B140 8 M8 Spring Washer 2 W019 9 M8 Flat Washer 2 W Rubber O-ring 2 C RLCP Pad FL/RR 1 M RLCP Pad FR/RL 1 M M10 x 45mm Hex Bolt 2 B M10 x 20mm Hex Bolt 2 B M10 Shakeproof Washer 2 W M10 x 38mm Flat Washer 2 W mm Security Allen Key 1 H Pad Cover Plate 2 M Fitting Instruction 1 R ,12 Crossbars sold individually Part No. Part No. 1250mm Heavy Duty Crossbar SILVER RB1250S 1375mm Heavy Duty Crossbar SILVER RB1375S 1250mm Heavy Duty Crossbar BLACK RB1250B 1375mm Heavy Duty Crossbar BLACK RB1375B 1260mm Vortex Crossbar SILVER VA126S 1375mm Vortex Crossbar SILVER VA137S 1260mm Vortex Crossbar BLACK VA126B 1375mm Vortex Crossbar BLACK VA137B Heavy Duty crossbar Vortex crossbar Tools Required: Torque wrench 16mm spanner HD crossbar Rubber Mallet Knife 10mm spanner VA crossbar only 5mm Security Allen key, included. T40 Torx Key, Renault Kangoo Tape Measure 1 Volkswagen Caddy/ Maxi. Remove the roof plugs using the 5mm Security Allen key provided. Renault Kangoo/ Maxi & Nissan Kubistar. Remove the roof plugs using a T40 Torx drive. Store the screws for replacement when racks are removed. Volkswagen Caddy/ Maxi Renault Kangoo/ Maxi Nissan Kubistar Page 3 of 6
4 2 Roof pad orientation rear bar system. The top surface of the pads have FR-RL and FL-RR marked on them. This denotes their position on the roof. Volkswagen Caddy Maxi Renault Kangoo Maxi FRONT FRONT FR-RL REAR FL-RR FR-RL REAR FL-RR 3 M8 x 25mm bolt M8 spring washer Fit pads to roof. Insert the M8 bolt/washer assembly through the pad. Screw into the roof using the allen key provided. Do not fully tighten at this stage. M8 flat washer O-ring outside of vehicle. 4 Align pads. Before tightening make sure the opposing pads are parallel across the vehicle. Tighten roof pads to 4-5 Nm/3-4 lb/ft. Parallel across vehicle. Page 4 of 6
5 5 VOLKSWAGEN Caddy Maxi - Leg height spacers for 3 crossbar system. To maintain level height across three bars spacers are used. Front crossbar uses two leg height spacers. Middle and rear crossbars do not require a leg height spacer. Longer bolts are supplied to suit leg height spacers. Item 4. Leg height spacer. Item 6. RLCPH Leg. Front M10 x 45mm bolt. Front Middle Rear 6 RENAULT Kangoo Maxi - 2* & 3 crossbar system. The taller roof rack support legs (RLCPH) are used at the rear for a 3 crossbar system. *The tall leg (RLCPH) is also used at the rear when using either the front or middle mount point for a 2 crossbar system. Item 6. RLCPH Leg. Front Middle Rear 7 M6 x 27mm bolt Fit Legs to base pads. Place leg onto the pad. Assemble the M6 screw and washers as shown. Insert the screw through the leg and into the pad. Do not fully tighten at this stage. M6 spring washer M6 flat washer RLCPH leg RLCP base pad 8 Crossbar rubber. Insert rubber into top of crossbar. Page 5 of 6
6 9 Fit crossbars. Place crossbars onto legs. Make sure the channel nut sits across the bar as shown below. Channel nut must sit across the bar when tight. 10 Check crossbar overhang. Measure for equal crossbar over hang. Tighten M6 x 27mm leg screws to 3-4 Nm/2-3 lb/ft. Tighten M10 x 20mm crossbar bolts to Nm/8-9 lb/ft. Tighten M6 screws. = = = Tighten M10 bolts. 11 Fit end caps. Use a rubber mallet to knock end caps into crossbar. Page 6 of 6
RLCP08 / RLCP08H. Important Information. Please refer to your vehicle owners manual for maximum roof loading. Always use lower of the two figures.
RLCP08 / RLCP08H Important Information Max: 100kg/220lbs. Please refer to your vehicle owners manual for maximum roof loading. Always use lower of the two figures. Recommendations: It is essential that
More informationRLCP27 Rhino Crossbar System Jeep Grand Cherokee
RLCP27 Rhino Crossbar System Jeep Grand Cherokee Maximum roof load: 68kg/149lbs Refer to vehicle manufacturers handbook for maximum roof loading. Always use lower of the two figures. Recommendations: It
More informationHyundai i30 & i40 Tourer RLCP40, RSP40/41
Hyundai i30 & i40 Tourer RLCP40, RSP40/41 Important Information Maximum roof load: 75kg/165lbs evenly distributed across two crossbars. Refer to vehicle owners manual for maximum roof loading. Always use
More informationToyota Kluger/Highlander SUV XU50 RLCP37
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Roof Rack System is installed in the correct location. Check the contents
More informationRLCP22 & RLCP22H Rhino Crossbar System
Rhino Crossbar System FIAT Ducato, Citroën Relay/Jumper, Peugeot Boxer, IVECO Daily, RAM ProMaster Important Information 1. Check Part No./Kit is correct 3. Fit roof rack accessory 2. Read through instruction
More informationRSP27 Rhino Sportz Two Crossbar System Jeep Grand Cherokee
RSP27 Rhino Sportz Two Crossbar System Jeep Grand Cherokee Important: Please read these instructions prior to installation. Check contents of kit before commencing fitment and report any discrepancies.
More informationRLT500 - Rhino Track Leg Kit
- Rhino Track Leg Kit Maximum carrying capacity: 100kg/220lbs evenly distributed over the crossbars. Please refer to your vehicle manufacturers handbook for maximum roof loading. Always use lower of these
More informationJeep Wrangler JK SG59 4dr & SG60 2dr- Rhino Sportz Gutter Mount
Jeep Wrangler JK 2011- SG59 4dr & SG60 2dr- Rhino Sportz Gutter Mount Important: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fitment and
More informationToyota Kluger RSP31. Maximum load carrying capacity: 80kg / 176lbs. Important Information. 1. Check Part No./Kit is correct 3. Fit roof rack accessory
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Roof Rack System is installed in the correct location. Check the contents
More informationRSP29 ISUZU MU-X Two Crossbars
Two Crossbars Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
More informationRLCP30 Leg Kit - To be used on Jeep Backbone RJKB1&2
Leg Kit - To be used on Jeep Backbone RJKB1&2 Important Information Max: 120kg (264lbs) - Three Crossbars. Max: 100 (220lbs) - Two Crossbars. Time: 30 mins. Read through instructions before installation.
More informationWARNING! 2 x Crossbars = 5kg. ? kg
WARNING ü ü km/h X 2 x Crossbars = 5kg? kg WARNING Important Load Carrying Instructions With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicle can be damaged if the item
More informationRhino-Rack Toyota Prado 3 Bar Heavy Duty System (RLCP23)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the racks are installed in the correct locations. Check the contents of
More informationFlexiglass - FlexiXover Canopy RTCFG02 RTCFG03
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Canopy Rack System is installed in the correct location. Check the
More informationWARNING! 2 x Crossbars = 5kg
WARNING!! ü!! km/h 2 x Crossbars = 5kg? kg - Please refer to your vehicle manufacturers handbook for maximum roof load capacity. - Any load transported on Roof Racks must be evenly distributed. - Instructions
More informationRhino Track Mount System
Tools required, Track install: Power drill Drill stop 5mm (3/6 ) drill bit Vacuum Cleaner Felt tip pen Carton knife Rivet gun/pneumatic Measuring tape Masking tape Automotive Butyl Sealant Caulking gun
More informationRLCP17 Rhino Heavy Duty Toyota landcruiser 200 Series Three Crossbar System.
RLCP17 Rhino Heavy Duty Toyota landcruiser 200 Series Three Crossbar System Place these instructions in vehicle s glovebox after installation is complete Important: Please read these instructions carefully
More informationRLT600 Crossbar System MERCEDES-BENZ Vito & Metris
RLT600 Crossbar System MERCEDES-BENZ Vito & Metris Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing fi tment and report any discrepancies.
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fi tment and report any discrepancies. Clean roof prior to installation.
More informationWARNING! 2 x Crossbars = 5kg
WARNING!! ü!! km/h 2 x Crossbars = 5kg? kg - Please refer to your vehicle manufacturers handbook for maximum roof load capacity. - Any load transported on Roof Racks must be evenly distributed. - Do not
More informationSX100. Place these instructions in the vehicle s glove box after installation is complete.
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction
More informationWARNING! 2 x Crossbars = 5kg. ? kg
WARNING!! ü! ü! km/h X 2 x Crossbars = 5kg? kg WARNING! Important Load Carrying Instructions With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicle can be damaged if
More informationRSP17 Rhino Toyota landcruiser 200 series Three Crossbar System.
Parts List RSP17 Rhino Toyota landcruiser 200 series Three Crossbar System. Place these instructions in vehicle s glovebox after installation is complete. Important: Please read these instructions carefully
More informationRhino-Rack Toyota Prado 2 Bar Aero Roof Rack System (RSP23)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the racks are installed in the correct locations. Check the contents of
More informationNissan Patrol Y62 RNPB1
Nissan Patrol Y62 RNPB1 Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct
More informationRhino 2500 series for Euro Crossbar.
Important: Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies.
More informationToyota 4Runner Track Mount Kit (RTS545)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Roof Rack System is installed in the correct location. Check the
More informationRhino Ski/ Snowboard Carrier 572, 573, 574, 576
Rhino Ski/ Snowboard Carrier 572, 573, 574, 576! Important: Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fi tment and report any discrepancies. Clean roof prior to installation.
More informationRhino 2500 Series - Two Bar Heavy Duty System.
. Important: Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies.
More informationJeep Wrangler JK 2dr Hard Top 2007 On
Important Information Max: 100kg (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you are unsure or have any questions, refer to the dealer or place of purchase.
More informationCare Instruction: Wash vehicle roof prior to installing Rhino Tracks.
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationToyota Hilux Track Mount (RTS543)
Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing fi tment and report any discrepancies. Place these instructions in the vehicle
More informationMitsubishi Triton Backbone RMTB1
Layout Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct location. Check
More informationRhino 2500 Series - Two Bar Heavy Duty System.
Rhino 2500 Series - Two Bar Heavy Duty System. Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit
More informationToyota Fortuner SX046
Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fi tment and report any discrepancies.
More informationRTS528 - Holden Colorado/ Isuzu D-MAX Space Cab Track Mount System
RTS528 - Holden Colorado/ Isuzu D-MAX Space Cab Track Mount System Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the
More informationJeep Wrangler JK 4dr Hard Top 11-14
Jeep Wrangler JK 4dr Hard Top 11-14 Important Information Max: 120kg (264lbs) - Three Crossbars. Max: 100 (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you
More informationRTS524 MITSUBISHI Challenger - Two Cross Bar Track Mount System - With or without roof rails -
RTS524 MITSUBISHI Challenger - Two Cross Bar Track Mount System - With or without roof rails - Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction
More informationJeep JK 2dr Backbone - RJKB2
Fit Time: 1.5 Hours IMPORTANT INFORMATION Maximum carrying capacity: On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance Rack Weight 95kg / 209lbs 63kg / 138lbs 240kg / 530lbs
More informationRTS518 - Rhino Heavy Duty 2 & 3 Crossbar System Hyundai iload, imax, i800, H-1.
RTS518 - Rhino Heavy Duty 2 & 3 Crossbar System Hyundai iload, imax, i800, H-1. NOTE: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fi tment
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationJeep Wrangler JK 4dr Hard Top n
Jeep Wrangler JK 4dr Hard Top 2007 0n Important Information Max: 120kg (264lbs) - Three Crossbars. Max: 100 (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you
More informationNM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System
NM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System Parts List Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
CONTROLLED Pioneer Tray, Pioneer Platform & Pioneer Tradie Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior
More informationRTS532 ISUZU MU-X LS-U & LS-M Trackmount
RTS532 ISUZU MU-X LS-U & LS-M Trackmount Assistance from a second person is recommended for the Track install. Please read these instructions carefully prior to installation. Check the contents of kit
More informationChannel Mount Generic Instructions (RDM01).
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Roof Rack System is installed in the correct location. Check the
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationSX055 VW Passat. 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
SX055 VW Passat Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fi tment and
More informationXTray Small (RMCB01)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the XTray is installed in the correct locations. Check the contents of
More information2500 RS Rhino Vortex - Two Bar System.
Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fi tment and report any discrepancies.
More informationRTS538 ISUZU MU-X LS-T Trackmount
Please read these instructions carefully prior to installation. Check the contents of kit before commencing fi tment and report any discrepancies. Please refer to your fi tting instruction to ensure that
More informationRTS527 - Holden Colorado/ Isuzu D-MAX Crew Cab Track Mount System
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRTS536 Toyota Prado 150 Track Mount
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the track mount system is installed in the correct location. Check the
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Important Information Maximum carrying capacity: Up to 100kg. Evenly distributed over the crossbars. connections should
More informationRhino-Rack Kayak T-Load 2 Hitch Mount (RTL002)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRhino Pioneer SXB (44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete.
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationJeep Wrangler JK 2dr Hard Top 2007 On
Important Information Max: 100kg (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you are unsure or have any questions, refer to the dealer or place of purchase.
More informationRTS510 Rhino Heavy Duty Track Mount System - MITSUBISHI TRITON MK
RTS510 Rhino Heavy Duty Track Mount System - MITSUBISHI TRITON MK Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the
More informationRSP15 Rhino Sportz - Honda CRV 2007 Two Crossbar System
RSP15 Rhino Sportz - Honda CRV 2007 Two Crossbar System Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to
More informationRhino-Rack SUNSEEKER II Mesh Room (32108)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationNM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System
NM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System Parts List Important: Care Instruction: Clean vehicle roof prior to fi tting Rhino Heavy Duty roof racks. Tools Required: Pneumatic or concertina
More informationMaximum load carrying capacity: 100kg / 220lbs. Important Information. 1. Check Part No./Kit is correct 3. Fit roof rack accessory
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct location. Check the contents
More informationRTS507 NISSAN Navara Dual Cab Track Mount System
Place these instructions in the vehicle s glove box after installation is complete. Parts List Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction
More informationLandrover Discovery 3 - Rhino Tracks.
Parts List Important: Landrover Discovery 3 - Rhino Tracks. Place these instructions in the vehicle s glove box after installation is complete. Please read these instructions carefully prior to installation.
More informationRBLW - Rear Boat Loader Worm Drive
RBLW - Rear Boat Loader Worm Drive Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please
More informationRhino-Rack Pioneer SX
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationToyota FJ Cruiser Backbone RFJB1
Toyota FJ Cruiser Backbone RFJB1 Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in
More informationRhino-Rack 2 Hitch Receiver Bike Carrier (4 Bikes)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationMS Short Multi Slide Step Ladder System
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction
More informationDownload your Vehicle Fitment Sheet
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationRhino 2500 series for Aero Crossbar.
Rhino 2500 series for Aero Crossbar. Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please
More informationRhino-Rack Rocky Mount Bike Carrier (RBC050)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRhino-Rack 4 Bike Carrier RBC044
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationToyota 4Runner Backbone - RT4B1
Fit Time: 1 Hour Important Information Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance Rack Weight 42102B 69kg / 152lb 49kg
More informationRhino Rack Bow Strap Bonnet Tie Down (RBAS1)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationRhino-Rack Kayak T-Load Tow Ball Mount (RTL001)
CONTROLLED Rhino-Rack Kayak T-Load Tow Ball Mount (RTL001) Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks
More informationRhino-Rack Hybrid Bike Carrier (RBC050)
CONTROLLED Rhino-Rack Hybrid Bike Carrier (RBC050) Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are
More informationUniversal Pioneer Platform (Flat Pack) 42114B/42115B
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationRhino-Rack Nautic Kayak Loader (NKL)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. heck the contents
More informationRhino Pioneer SXB (44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete.
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationRhino 2500 Series. 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
Important: Rhino 2500 Series 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fitment and
More informationRhino-Rack ROC25 Crossbar Kit - RLKVF, RLKVFH, RLKVF2, RLKVF2H
Rhino-Rack ROC25 Crossbar Kit - RLKVF, RLKVFH, RLKVF2, RLKVF2H Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the
More informationRhino Tourmaster Alloy Tray (RTAT)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRhino-Rack Nautic Kayak Loader (NKL)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. heck the contents
More informationToyota Prado 120 Backbone - RTPB2
Toyota Prado 120 Backbone - RTPB2 Fit Time: 1.5 Hours Layout: IMPORTANT INFORMATION Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance
More informationToyota Prado 150 Backbone - RTPB1
Fit Time: 1.5 Hours Layout: IMPORTANT INFORMATION Maximum carrying capacity: Suitable Suitable On Road Cargo Off Road Cargo Pioneers On Road & Off Road Cargo Allowance Pioneers Allowance Allowance Static
More informationHolden Colorado / Isuzu Dmax D/Cab Side Steps Kit (SS003) On
Holden Colorado / Isuzu Dmax D/Cab Side Steps Kit (SS003) 2012 - On Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the
More informationToyota Fortuner GLX/GX & Crusade Backbone - RTFB1
Toyota Fortuner GLX/GX & Crusade Backbone - RTFB1 Fit time: 1.5 hours Note: OEM roof rails removed. IMPORTANT INFORMATION Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo
More informationImportant Information
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRhino Zenith Masterfit Luggage Box
RMFZ66 RMFZ86 Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please refer to your fitting
More informationFord Ranger / Mazda BT-50 D/Cab Side Steps Kit (SS002) On
Ford Ranger / Mazda BT-50 D/Cab Side Steps Kit (SS002) 2012 - On Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof
More informationRhino-Rack Hybrid Bike Carrier (RBC050)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRhino-Rack 4 Bike Carrier RBC044
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationRhino Master Fit Luggage Boxes
Rhino Master Fit Luggage Boxes Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing
More informationLOCKN LOAD. MAX VEHICLE ROOF LOAD RATING: 100KG (2 Leg Pairs) 150KG (3 Leg Pairs) TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES + CARGO
LOCKN LOAD TM GUTTER MOUNT KIT GUTTER MOUNT HEAVY DUTY ROOF RACK ATTACHMENT SYSTEM MAX VEHICLE ROOF LOAD RATING: 00KG ( Leg Pairs) 50KG (3 Leg Pairs) TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES
More informationK327W. Fitting Kit. Fitting Instructions for Basic Carrier. x 4 x 4 x 4 x 4. Revision No: 5E 1
Fitting Kit Fitting Instructions for Basic Carrier x 4 x 4 x 4 x 4 Revision No: 5E 1 Items you will require: Attention: First Time Installation Tape measure Pen Cordless drill Depth stop Vacuum cleaner
More informationK491. Fitting Kit. Fitting Instructions for Basic Carrier. x 4 x 5 x 5 x 4. x 4 x 8 x 4 x 2. x 2. Revision No: 1.2
Fitting Instructions for Basic Carrier x 4 x 5 x 5 x 4 x 4 x 8 x 4 x 2 x 2 Revision No: 1.2 1 MAX kg W/P WHD MAX kg W/P WHD Audi A3 Sportback, 5dr Hatch 04-+ EU 60 60 A3 Sportback, 5dr Hatch Mar 05-+ NZ
More informationFIRST TIME INSTALLATION
LOCKN LOAD TM PLATFORM MAX PLATFORM LOAD RATING: 100 KG (sizes A, B, F, G, I, K, & L) 150 KG (sizes C, D, E, H, J, N, P & U) PLEASE REFER TO VEHICLE MANUFACTURER SPECIFICATIONS FOR MAX ROOF LOAD RATING
More information