Rhino-Rack 4 Bike Carrier RBC044
|
|
- Austin Johns
- 6 years ago
- Views:
Transcription
1 Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the bike rack is installed in the correct locations. Check the contents of kit before commencing fi tment and report any discrepancies. Place these instructions in the vehicle s glove box after installation is complete. Layout Maximum carrying capacity: 15kg (33lbs) per bike. Max 4 Bikes. Totalling 60kg/ 130lbs. Warning: Do not attempt to fit the bike carrier to your vehicle unless you fully understand this fi tting instructions. Please direct any questions regarding fi tting to the dealer from where the bike carrier was purchased. Use only non-stretch fastening ropes or straps. Recommendations: It is essential that all bolt connections be checked after driving a short distance when you fi rst install your bike carrier. Bolt connections should be checked again at regular intervals (once a week is enough, depending on road conditions, usage, loads and distances travelled). You should also check the bike carrier each time it is re-fi tted. Always make sure to fasten your load securely. Please also ensure that all loads are evenly distributed and that the centre of gravity is kept as low as possible. Bike carrier must be removed when putting vehicle through an automatic car wash. In some states it may be against the law to obstruct clear view of lamps and registration plates. It is suggested that the Rhino- Rack Number Plate Holder (RBCA011) be purchased. Caution: The handling characteristics of the vehicle changes when you transport a load on the roof or at the rear. For safety reasons we recommend you exercise extreme care when transporting wind-resistant loads. Special consideration must be taken into account when cornering and braking. Note for Dealers and Fitters Important Information
2 General Parts List Item Component Name Qty Part No. 1 Support Arm 1-2 Mast 1-3 Receiving Bar 1-4 Multi Facted Bike Holders 4-5 Rubber Straps 12-6 Lever 1-7 Instructions 1 R Tools Required: 1: Socket Wrench 2: Allen Key Note: Check all Box are present Straps - 1 Hitch Bolt (with washers) - 1 Pivot Bolt (with washers and nut) - 3 Celvis Pins - 1 Safety Strap - 1 Allen Key Instructions 1 Install the Mast to the Receiving Bar. 2 Align the holes on the Mast with those on the Receiving Bar. 3 Insert the Security Pin (which was pre installed in the Mast) to the upper hole of the Hitch Receiver. 4 Be sure the Pin is completely through the Mast and Hitch Receiver.
3 5 Insert the Clevis Pin into the hole of the Security Pin. 6 Insert the Pivot Bolt into the Lower hole of the Receiving Bar. 7 The two Flat Washers must be against either side of the Draw Bar. 8 Install the Locking Nut. Use a Socket Wrench to install. 9 Now install the Rack to the Hitch Receiver. Align the holes. Note: If you have a 1 1/4 Receiver you will need to use an Allen Key to disconnect the Sleeve from the Receiving Bar. 10 Place the Bike onto the Bike Carrier. The Frame of the Bike will fi t into the Cradle on the Bike Barrier as shown. The rear of the Bike should be secured here.
4 11 Using the Rubber Straps on the Carrier, Fix the rear of the Frame in place. Loop a Strap over the top of the Frame and secure in place. Loop a Strap around the rear of the Frame and secure as shown. 12 Using the Rubber Straps on the Carrier, Fix the front of the Frame in place. 13 Fix the bikes in place using the Strap provided. Wrap the Strap through both wheels of the bike and around the Back of the Bike Carrier
5 Note Top View: For additional Bikes (4 max), face Bike in alternate directions. This will ensure the Bikes will not clash together during travel. Ensure there is no obstruction of view to lamps and registration plates, adjust fork positions to achieve this if required To access the rear of the vehicle, remove the Security Pin. Lift up the Lever as shown. The Rack will tilt forward. This is only to be done when bikes are not on the Rack. Note: Check the Bikes do not cover/ block the Tail Lights and Licence Plate. An RBCA011 (License Plate Holder) may be required to meet road and safety regulations in your state.
Rhino-Rack 4 Bike Carrier RBC044
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationRhino Ski/ Snowboard Carrier 572, 573, 574, 576
Rhino Ski/ Snowboard Carrier 572, 573, 574, 576! Important: Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before
More informationRhino-Rack Kayak T-Load Tow Ball Mount (RTL001)
CONTROLLED Rhino-Rack Kayak T-Load Tow Ball Mount (RTL001) Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks
More informationXTray Small (RMCB01)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the XTray is installed in the correct locations. Check the contents of
More informationRhino-Rack 2 Hitch Receiver Bike Carrier (4 Bikes)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationToyota FJ Cruiser Backbone RFJB1
Toyota FJ Cruiser Backbone RFJB1 Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in
More informationRSP15 Rhino Sportz - Honda CRV 2007 Two Crossbar System
RSP15 Rhino Sportz - Honda CRV 2007 Two Crossbar System Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to
More informationRBLW - Rear Boat Loader Worm Drive
RBLW - Rear Boat Loader Worm Drive Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please
More informationMitsubishi Triton Backbone RMTB1
Layout Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct location. Check
More informationMaximum load carrying capacity: 100kg / 220lbs. Important Information. 1. Check Part No./Kit is correct 3. Fit roof rack accessory
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct location. Check the contents
More informationNissan Patrol Y62 RNPB1
Nissan Patrol Y62 RNPB1 Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct
More informationRhino-Rack Kayak T-Load 2 Hitch Mount (RTL002)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fi tment and report any discrepancies. Clean roof prior to installation.
More informationRSP29 ISUZU MU-X Two Crossbars
Two Crossbars Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
More informationRhino-Rack Hybrid Bike Carrier (RBC050)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationToyota Fortuner SX046
Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fi tment and report any discrepancies.
More informationRTS507 NISSAN Navara Dual Cab Track Mount System
Place these instructions in the vehicle s glove box after installation is complete. Parts List Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction
More informationToyota 4Runner Track Mount Kit (RTS545)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Roof Rack System is installed in the correct location. Check the
More informationToyota Kluger RSP31. Maximum load carrying capacity: 80kg / 176lbs. Important Information. 1. Check Part No./Kit is correct 3. Fit roof rack accessory
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Roof Rack System is installed in the correct location. Check the contents
More informationRhino 2500 Series - Two Bar Heavy Duty System.
Rhino 2500 Series - Two Bar Heavy Duty System. Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit
More informationRhino 2500 series for Aero Crossbar.
Rhino 2500 series for Aero Crossbar. Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please
More informationRhino-Rack Rocky Mount Bike Carrier (RBC050)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationSX055 VW Passat. 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
SX055 VW Passat Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fi tment and
More informationRhino-Rack Toyota Prado 2 Bar Aero Roof Rack System (RSP23)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the racks are installed in the correct locations. Check the contents of
More informationRhino-Rack Hybrid Bike Carrier (RBC050)
CONTROLLED Rhino-Rack Hybrid Bike Carrier (RBC050) Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are
More information2500 RS Rhino Vortex - Two Bar System.
Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fi tment and report any discrepancies.
More informationRTS536 Toyota Prado 150 Track Mount
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the track mount system is installed in the correct location. Check the
More informationRLT600 Crossbar System MERCEDES-BENZ Vito & Metris
RLT600 Crossbar System MERCEDES-BENZ Vito & Metris Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing fi tment and report any discrepancies.
More informationMS Short Multi Slide Step Ladder System
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction
More informationNM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System
NM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System Parts List Important: Care Instruction: Clean vehicle roof prior to fi tting Rhino Heavy Duty roof racks. Tools Required: Pneumatic or concertina
More informationRhino-Rack Toyota Prado 3 Bar Heavy Duty System (RLCP23)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the racks are installed in the correct locations. Check the contents of
More informationToyota 4Runner Backbone - RT4B1
Fit Time: 1 Hour Important Information Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance Rack Weight 42102B 69kg / 152lb 49kg
More informationToyota Fortuner GLX/GX & Crusade Backbone - RTFB1
Toyota Fortuner GLX/GX & Crusade Backbone - RTFB1 Fit time: 1.5 hours Note: OEM roof rails removed. IMPORTANT INFORMATION Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo
More informationChannel Mount Generic Instructions (RDM01).
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Roof Rack System is installed in the correct location. Check the
More informationRSP27 Rhino Sportz Two Crossbar System Jeep Grand Cherokee
RSP27 Rhino Sportz Two Crossbar System Jeep Grand Cherokee Important: Please read these instructions prior to installation. Check contents of kit before commencing fitment and report any discrepancies.
More informationToyota Prado 150 Backbone - RTPB1
Fit Time: 1.5 Hours Layout: IMPORTANT INFORMATION Maximum carrying capacity: Suitable Suitable On Road Cargo Off Road Cargo Pioneers On Road & Off Road Cargo Allowance Pioneers Allowance Allowance Static
More informationRhino 2500 series for Euro Crossbar.
Important: Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies.
More informationRhino-Rack Nautic Kayak Loader (NKL)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. heck the contents
More informationRLCP27 Rhino Crossbar System Jeep Grand Cherokee
RLCP27 Rhino Crossbar System Jeep Grand Cherokee Maximum roof load: 68kg/149lbs Refer to vehicle manufacturers handbook for maximum roof loading. Always use lower of the two figures. Recommendations: It
More informationToyota Hilux Track Mount (RTS543)
Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing fi tment and report any discrepancies. Place these instructions in the vehicle
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fi tment and report any discrepancies. Clean roof prior to installation.
More informationToyota Prado 120 Backbone - RTPB2
Toyota Prado 120 Backbone - RTPB2 Fit Time: 1.5 Hours Layout: IMPORTANT INFORMATION Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance
More informationWARNING! 2 x Crossbars = 5kg
WARNING!! ü!! km/h 2 x Crossbars = 5kg? kg - Please refer to your vehicle manufacturers handbook for maximum roof load capacity. - Any load transported on Roof Racks must be evenly distributed. - Do not
More informationRhino 2500 Series - Two Bar Heavy Duty System.
. Important: Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies.
More informationUniversal Pioneer Platform (Flat Pack) 42114B/42115B
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationToyota Kluger/Highlander SUV XU50 RLCP37
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Roof Rack System is installed in the correct location. Check the contents
More informationSX100. Place these instructions in the vehicle s glove box after installation is complete.
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction
More informationRhino-Rack ROC25 Crossbar Kit - RLKVF, RLKVFH, RLKVF2, RLKVF2H
Rhino-Rack ROC25 Crossbar Kit - RLKVF, RLKVFH, RLKVF2, RLKVF2H Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the
More informationRTS518 - Rhino Heavy Duty 2 & 3 Crossbar System Hyundai iload, imax, i800, H-1.
RTS518 - Rhino Heavy Duty 2 & 3 Crossbar System Hyundai iload, imax, i800, H-1. NOTE: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fi tment
More informationRhino-Rack Pioneer SX
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationRhino-Rack SUNSEEKER II Mesh Room (32108)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRhino 2500 Series. 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
Important: Rhino 2500 Series 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fitment and
More informationJeep JK 2dr Backbone - RJKB2
Fit Time: 1.5 Hours IMPORTANT INFORMATION Maximum carrying capacity: On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance Rack Weight 95kg / 209lbs 63kg / 138lbs 240kg / 530lbs
More informationJeep Wrangler JK SG59 4dr & SG60 2dr- Rhino Sportz Gutter Mount
Jeep Wrangler JK 2011- SG59 4dr & SG60 2dr- Rhino Sportz Gutter Mount Important: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fitment and
More informationRSP17 Rhino Toyota landcruiser 200 series Three Crossbar System.
Parts List RSP17 Rhino Toyota landcruiser 200 series Three Crossbar System. Place these instructions in vehicle s glovebox after installation is complete. Important: Please read these instructions carefully
More informationRLCP17 Rhino Heavy Duty Toyota landcruiser 200 Series Three Crossbar System.
RLCP17 Rhino Heavy Duty Toyota landcruiser 200 Series Three Crossbar System Place these instructions in vehicle s glovebox after installation is complete Important: Please read these instructions carefully
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Important Information Maximum carrying capacity: Up to 100kg. Evenly distributed over the crossbars. connections should
More informationRTS538 ISUZU MU-X LS-T Trackmount
Please read these instructions carefully prior to installation. Check the contents of kit before commencing fi tment and report any discrepancies. Please refer to your fi tting instruction to ensure that
More informationImportant Information
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRhino-Rack Nautic Kayak Loader (NKL)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. heck the contents
More informationRTS528 - Holden Colorado/ Isuzu D-MAX Space Cab Track Mount System
RTS528 - Holden Colorado/ Isuzu D-MAX Space Cab Track Mount System Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the
More informationWARNING! 2 x Crossbars = 5kg. ? kg
WARNING ü ü km/h X 2 x Crossbars = 5kg? kg WARNING Important Load Carrying Instructions With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicle can be damaged if the item
More informationRTS510 Rhino Heavy Duty Track Mount System - MITSUBISHI TRITON MK
RTS510 Rhino Heavy Duty Track Mount System - MITSUBISHI TRITON MK Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the
More informationLandrover Discovery 3 - Rhino Tracks.
Parts List Important: Landrover Discovery 3 - Rhino Tracks. Place these instructions in the vehicle s glove box after installation is complete. Please read these instructions carefully prior to installation.
More informationRTS527 - Holden Colorado/ Isuzu D-MAX Crew Cab Track Mount System
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRhino Tourmaster Alloy Tray (RTAT)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationWARNING! 2 x Crossbars = 5kg
WARNING!! ü!! km/h 2 x Crossbars = 5kg? kg - Please refer to your vehicle manufacturers handbook for maximum roof load capacity. - Any load transported on Roof Racks must be evenly distributed. - Instructions
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
CONTROLLED Pioneer Tray, Pioneer Platform & Pioneer Tradie Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationRLCP08R- Rear Crossbar
- Rear Crossbar VOLKSWAGEN Caddy Maxi MY11> RENAULT Kangoo Maxi MY13> Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fitment
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationRLCP22 & RLCP22H Rhino Crossbar System
Rhino Crossbar System FIAT Ducato, Citroën Relay/Jumper, Peugeot Boxer, IVECO Daily, RAM ProMaster Important Information 1. Check Part No./Kit is correct 3. Fit roof rack accessory 2. Read through instruction
More informationJeep Wrangler JK 2dr Hard Top 2007 On
Important Information Max: 100kg (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you are unsure or have any questions, refer to the dealer or place of purchase.
More informationNM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System
NM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System Parts List Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the
More informationFlexiglass - FlexiXover Canopy RTCFG02 RTCFG03
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Canopy Rack System is installed in the correct location. Check the
More informationDownload your Vehicle Fitment Sheet
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationRhino Pioneer SXB (44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete.
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationRLT500 - Rhino Track Leg Kit
- Rhino Track Leg Kit Maximum carrying capacity: 100kg/220lbs evenly distributed over the crossbars. Please refer to your vehicle manufacturers handbook for maximum roof loading. Always use lower of these
More informationRhino Track Mount System
Tools required, Track install: Power drill Drill stop 5mm (3/6 ) drill bit Vacuum Cleaner Felt tip pen Carton knife Rivet gun/pneumatic Measuring tape Masking tape Automotive Butyl Sealant Caulking gun
More informationRTS524 MITSUBISHI Challenger - Two Cross Bar Track Mount System - With or without roof rails -
RTS524 MITSUBISHI Challenger - Two Cross Bar Track Mount System - With or without roof rails - Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction
More informationWARNING! 2 x Crossbars = 5kg. ? kg
WARNING!! ü! ü! km/h X 2 x Crossbars = 5kg? kg WARNING! Important Load Carrying Instructions With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicle can be damaged if
More informationCare Instruction: Wash vehicle roof prior to installing Rhino Tracks.
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationJeep Wrangler JK 4dr Hard Top n
Jeep Wrangler JK 4dr Hard Top 2007 0n Important Information Max: 120kg (264lbs) - Three Crossbars. Max: 100 (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you
More informationRLCP30 Leg Kit - To be used on Jeep Backbone RJKB1&2
Leg Kit - To be used on Jeep Backbone RJKB1&2 Important Information Max: 120kg (264lbs) - Three Crossbars. Max: 100 (220lbs) - Two Crossbars. Time: 30 mins. Read through instructions before installation.
More informationRhino Rack Bow Strap Bonnet Tie Down (RBAS1)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationPART NUMBER: E361SAJ400
A KIT CONTENTS: Do not use this product with hitch extenders. PIVOT BOLT (1X) PIVOT WASHER (2X) PIVOT NUT (1X) HITCH BOLT (1X) LOCK WASHER (1X) WASHER(1X) SAFETY CLIP (1X) STRAP (6X) BASE (1X) LOCKING
More informationRhino Pioneer SXB (44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete.
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationHyundai i30 & i40 Tourer RLCP40, RSP40/41
Hyundai i30 & i40 Tourer RLCP40, RSP40/41 Important Information Maximum roof load: 75kg/165lbs evenly distributed across two crossbars. Refer to vehicle owners manual for maximum roof loading. Always use
More informationRhino Master Fit Luggage Boxes
Rhino Master Fit Luggage Boxes Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing
More informationRTS532 ISUZU MU-X LS-U & LS-M Trackmount
RTS532 ISUZU MU-X LS-U & LS-M Trackmount Assistance from a second person is recommended for the Track install. Please read these instructions carefully prior to installation. Check the contents of kit
More informationRLCP08 / RLCP08H. Important Information. Please refer to your vehicle owners manual for maximum roof loading. Always use lower of the two figures.
RLCP08 / RLCP08H Important Information Max: 100kg/220lbs. Please refer to your vehicle owners manual for maximum roof loading. Always use lower of the two figures. Recommendations: It is essential that
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationHolden Colorado / Isuzu Dmax D/Cab Side Steps Kit (SS003) On
Holden Colorado / Isuzu Dmax D/Cab Side Steps Kit (SS003) 2012 - On Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the
More informationRhino Zenith Masterfit Luggage Box
RMFZ66 RMFZ86 Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please refer to your fitting
More informationFord Ranger / Mazda BT-50 D/Cab Side Steps Kit (SS002) On
Ford Ranger / Mazda BT-50 D/Cab Side Steps Kit (SS002) 2012 - On Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof
More informationB C A. EN bike trays with ratchet arms 2. EN front wheel holder 2. EN rear wheel holder assembly 2. EN 4mm self tapping screw 10
T2 PRO 9036 2 BIKE ADD-ON FOR (2" HITCH) = North American English PARTS INCLUDED B C A D A E F G H I J K L M N part description qty. A add-on mast 1 B bike trays with ratchet arms 2 C front wheel holder
More informationDO NOT USE THIS PRODUCT WITH HITCH EXTENDERS. USE ONLY YAKIMA ADAPTERS WITH THIS PRODUCT. DO NOT USE ANY OTHER BRAND TONGUE ADAPTER.
FlipSide 4 DO NOT USE THIS PRODUCT WITH HITCH EXTENDERS. USE ONLY YAKIMA ADAPTERS WITH THIS PRODUCT. DO NOT USE ANY OTHER BRAND TONGUE ADAPTER. For Your Safety Warranty Registration on-line YAKIMA.com
More informationBag height and brush adjustment Adjust clevis up or down to make sure that the bag clears the ground when attached to tractor.
18 Cubic Foot Professional Grade Lawn Sweeper Model No. 42SWP18 Large capacity 18 cubic foot hopper. Easy to dump bag. No-slip brush height adjustment. Free wheels in reverse. Stores upright for space
More informationHaul-Your-Might T3. Product Name: Product Code: Please read all instructions carefully before assembly, installation and/or use of this product.
WARNING: DO NOT exceed 800 lbs. (363 Kgs) WARNING: DO NOT exceed vehicle manufacturer s weight rating. Haul-Your-Might T3 Tools Required: 17mm Socket 5mm Hex Key 1/8 Hex Key Tape Measure 17mm Wrench 13mm
More informationInstallation Instructions. Universal Accessories, Bike Holder Development. All Vehicle Production ASSEMBLY OF RACK HOURS
Page 1 of 7 Installation Instructions March 2004 Universal Accessories, Bike Holder Accessory Development SUBJECT MODEL MINI LINK SYSTEM BIKE HOLDER- PIN 82110154540 Cooper (R50) and Cooper S (R53) All
More information