Mark 608 Series. Pressure Regulators Mark 608 Gas Pressure Regulators. Gas Pressure Regulators. Specifications. CRN Registration Number Available
|
|
|
- Rosalind Snow
- 5 years ago
- Views:
Transcription
1 Mark 608 Series Gas Pressure Regulators The 1-1/2" and 2" size Mark 608 valves are for use on large tank blanketing applications or other low pressure gas regulation. In a tank blanketing application, the Mark 608 is used to control the flow of the blanketing gas into the tank to maintain the proper positive pressure. Once the blanket has been established, a small flow of nitrogen is continually admitted to the tank to keep the blanket fresh. These valves are often used in conjunction with Jordan's Mark 508 back pressure gas regulator, used to vent gas from the tank to prevent blanketing pressure from rising to a level that could damage the tank. The Mark 608 comes standard with an extra large diaphragm to give set point control as low as 2.0" W.C. (4,98 mbar). In addition, the "S" pattern body design allows for high flow capacity and also gives the option of having bubble tight shutoff. Sizes: 1-1/2" (DN40) & 2" (DN50) End Connections Threaded NPT, BSPT, BSPP Flanged 150#, 300#, PN16, PN40 Others upon request Materials Body: Bronze (B61), Carbon Steel (WCB), Stainless Steel (CF8M) Trim: 316 Stainless Steel Seat: 316 Stainless Steel Diaphragm: Buna-N/Nylon, Viton/Nomex and EPDM with Polyester reinforcement Soft seat and o-rings match diaphragm material Shutoff: ANSI Class VI 1-1/2" 2" Specifications CRN Registration Number Available Ranges 2 to 5 inches w.c. (5,0 to 12,5 mbar)* 4 to 8 inches w.c. (10,0 to 20 mbar)* 8 to 28 inches w.c. (20 to 70 mbar)* 10 to 17 inches w.c. (25 to 42 mbar) 14 to 28 inches w.c. (35 to 70 mbar) 0.75 to 1 psi (52 to 69 mbar) 1 to 2 psi (69 to 138 mbar) 1.5 to 3 psi (0,10 to 0,21 bar) 3 to 5 psi (0,21 to 0,34 bar) Cv Rating: 23 (20 Kv) Pressure Temperature Rating F (4,1 37,8 C) F (4,1 135 C) Maximum Downstream Pressure: 25 psig (1,7 bar) *Inverted mounting is required for set points below 10" wc. Pressure Regulators Mark 608 Gas Pressure Regulators Jordan a division of Richards Industries 3170 Wasson Road Cincinnati, OH (f) info@richardsind.com
2 Dimensions (NPT, SWE, BSPT, BSPP Ends) 15.0 D C B 3/4" FNPT Vent (Top) 3/4" FNPT Sensing Tap (Bottom) Dimensions (inches) lbs 1-1/2" " /4" FNPT Sensing Port A Dimensions (metric) kgs DN40 171,5 125, DN50 171,5 125, Dimensions (150# Flanged Ends) 15.0 D C B 3/4" FNPT Vent (Top) 3/4" FNPT Sensing Tap (Bottom) Dimensions (inches) lbs 1-1/2" " * IFE only " for WFE and TFE 3/4" FNPT Sensing Port A Dimensions (metric) kgs DN40 222,3 125, DN , * IFE only. 279,45mm for WFE and TFE *Inverted Mounting is required for set points below 10" wc
3 Dimensions (300# Flanged Ends) 15.0 D 3/4" FNPT Vent (Top) C 3/4" FNPT Sensing Tap (Bottom) B 3/4" FNPT Sensing Port A ANSI Dimensions (inches) Size Flange A B C D lbs 1-1/2" 300# 9.25* " 300# * IFE only " for WFE and TFE ANSI Dimensions (metric) Size Flange A B C D kgs DN40 PN40 235,0* 125, DN50 PN40 266,7 125, * IFE only. 279,45mm for WFE and TFE *Inverted Mounting is required for set points below 10" wc
4 Range Set Point Accuracy 1-1/2" Mark 608 Series Capacities 2.0 psi (0,14 bar) 3.0 psi (0,21 bar) 5.0 psi (0,34 bar) WC 3.0" WC 0.75" WC ,0-12,5 mbar 7,5 mbar 1,9 mbar psi (0.7 bar) 15.0 psi (1,0 bar) Inlet Pressure 20.0 psi (1,4 bar) 25.0 psi (1,7 bar) 30.0 psi (2,1 bar) 40.0 psi (2,8 bar) 50.0 psi (3,5 bar) 60.0 psi (4,1 bar) " WC 10,0-20,0 mbar " WC 20,0-70,0 mbar 5.0" WC " WC 7.0" WC ,5 mbar ,5 mbar 17,4 mbar " WC " WC 25.0" WC ,9 mbar ,7 mbar 62,3 mbar " WC 12.0" WC " WC 15.0" WC ,9-42,4 mbar 28,9 mbar ,0 mbar 37,4 mbar " WC 15.0" WC " WC 25.0" WC ,9-70,0 mbar 37,4 mbar ,2 mbar 62,3 mbar psi 51,7-69,0 mbar 1-2 psi 69,0-137,9 mbar psi ,21 bar 3-5 psi 0,21-0,34 mbar 0.75 psi psi 1 psi ,7 mbar 12, ,8 mbar mbar psi psi 2.0 psi ,10 bar 20, ,14 bar mbar psi psi 3.0 psi ,14 bar 27, ,21 bar mbar psi psi 5.0 psi ,24 bar 34, ,34 bar mbar Nitrogen at 0.97 s.g. in scfh and Nm 3 /hr Operation in shaded areas not recommended
5 Range Set Point Accuracy 2.0 psi 3.0 psi 5.0 psi (0,14 bar) (0,21 bar) (0,34 bar) WC 3.0" WC 0.75" WC ,0-12,5 mbar 7,5 mbar 1,9 mbar " Mark 608 Series Capacities 10.0 psi (0.7 bar) 15.0 psi (1,0 bar) Inlet Pressure 20.0 psi (1,4 bar) 25.0 psi (1,7 bar) 30.0 psi (2,1 bar) 40.0 psi (2,8 bar) 50.0 psi (3,5 bar) 60.0 psi (4,1 bar) " WC 10,0-20,0 mbar " WC 20,0-70,0 mbar 5.0" WC " WC 7.0" WC ,5 mbar ,5 mbar 17,4 mbar " WC " WC 25.0" WC ,9 mbar ,7 mbar 62,3 mbar " WC 12.0" WC " WC 15.0" WC ,9-42,4 mbar 28,9 mbar ,0 mbar 37,4 mbar " WC 15.0" WC " WC 25.0" WC ,9-70,0 mbar 37,4 mbar ,2 mbar 62,3 mbar psi 51,7-69,0 mbar 1-2 psi 69,0-137,9 mbar psi ,21 bar 3-5 psi 0,21-0,34 mbar 0.75 psi psi 1 psi ,7 mbar ,9 mbar 68,8 mbar psi psi 2.0 psi ,10 bar ,7 mbar 0,14 bar psi psi 3.0 psi ,14 bar ,5 mbar 0,21 bar psi psi 5.0 psi ,24 bar ,4 mbar 0,34 bar Nitrogen at 0.97 s.g. in scfh and Nm 3 /hr Operation in shaded areas not recommended
6 MK608/0414/2K/B Ordering Schematic Model No Size Body Mat'l Model 608 Standard Size /2" (DN40) 200 2" (DN50) BR CS S6 Body Material Bronze Carbon Steel (WCB) Stainless Steel (CF8M) 1 & 2 End Connections PT NPT BT BSPT BP BSPP SW FSW F1 125#FE F5 150# FE F2 250# FE F3 300# FE F7 PN10 DIN FE F6 PN16 DIN FE F8 PN25 DIN FE F4 PN40 DIN FE I3 IFE 300# I5 IFE 150# 3 & 4 Seat & Diaphragm BN Buna - N VN Viton EN EPDM 5 & 6 Range W.C. mbar " W.C. 5,0-12,5 mbar " W.C. 10,0-19,9 mbar " W.C. 19,9-70,0 mbar " W.C. 24,9-42,3 mbar " W.C. 34,9-70,0 mbar psi 51,7-69,0 mbar psi 69,0-137,9 mbar psi 0,10-0,21 bar psi 0,21-0,34 bar 7 & 8 Actuator SD Standard 9 & 10 Bushing TF Teflon CG Carbon Graphite 11 & 12 PED Compliance 00 Not Required FF CE Category 1 Note: Inverted mounting is required for set points below 10" wc. Jordan a division of Richards Industries 3170 Wasson Road Cincinnati, OH (f) info@richardsind.com
Mark 608BP Series. Pressure Regulators Mark 608BP Gas Pressure Regulators. Balanced Plug Gas Pressure Regulators. Features
Mark 608BP Series Balanced Plug Gas Pressure Regulators The Mark 608BP Balanced Plug Gas Pressure Regulator is the ideal valve for low pressure gas regulation with higher inlet pressures. The selfcontained
Mark 78 Series. Control Valves Mark 78 Globe Style Control Valves. Globe Style Control Valve. Function. Features. CRN Registration Number Available
Mark 78 Series Globe Style Control Valve The Mark 78 pneumatic control valve is designed for accurate performance and simplified maintenance. This versatile product can be used on a variety of applications,
Mark 695 Series. Pressure Regulators Mark 695 Piloted Tank Blanketing Regulators. Piloted Tank Blanketing Regulator 3/4"- 1" Optional Features
Mark 695 Series Piloted Tank Blanketing Regulator 3/4"- 1" The Mark 695 Series piloted soft seat regulator was designed specifically to provide accurate pressure control on very low pressure tank blanketing
Mark 63/64 Series. Pressure Regulators Mark 63/64 Differential Pressure Regulators. Differential Pressure Regulators. Features
Mark 63/64 Series Differential Pressure Regulators The Jordan Mark 63 is designed to maintain a constant differential between the pressure on the discharge side of the regulator and the signal pressure
Mark 50 Series. Back Pressure Regulators Mark 50 Self-Operated Back Pressure Regulators. Self-Operated Back Pressure Regulators.
Mark 50 Series Self-Operated Back Pressure Regulators The Mark 50 Sliding Gate Back Pressure Regulator is used to regulate upstream pressure at a predetermined setpoint. The spring in the Mark 50 holds
Mark 33 Series. Control Valves Mark 33/39 Electric Motor Control Valves. Electric Motor Control Valves. Features. CRN Registration Number Available
Mark 33 Series Electric Motor Control Valves The Mark 33 is a motor operated valve featuring the Jordan sliding gate seat and heavy-duty industrial motors for proportional (resistance), on-off, 4-20mA
Mark 675 Series. Pressure Regulators Mark 675 Pressure Regulators. Self-Operated Pressure Regulators. Mark 675 Features
Mark 675 Series Self-Operated Pressure Regulators The Mark 675 Wafer Style Sliding Gate Pressure Regulator is used to regulate the downstream pressure to a predetermined setpoint. The spring in the Mark
Mark 53/54 Series. Pressure Regulators Mark 53 Differential Back Pressure Regulators. Differential Back Pressure Regulators.
Mark 53/54 Series ifferential Back Pressure Regulators The Jordan Mark 53 maintains a constant differential between the inlet pressure and the pressure loaded on top of the diaphragm. It can be used for
Pneumatic Control Valves Mark 70 Sliding Gate Control Valves. Sliding Gate Control Valves. 3L/T-2R/S33 Series Mark 70 Series.
3L/T-2R/S33 Series Mark 7 Series Sliding Gate Control Valves The Mark 7 Series is a line of pneumatically-operated diaphragm control valves that combine multiple spring actuators with the precision of
Mark 89/89MX Series. Temperature Regulators Mark 89/89MX Three-Way Temperature Regulators. Three-Way Temperature Regulators.
Mark 89/89MX Series Three-Way Temperature Regulators The Mark 89 is used for diverting service and is ideal for bypassing fluids around coolers or filters. In this configuration, there is one inlet and
Pneumatic Control Valves Mark 70 Sliding Gate Control Valves. Sliding Gate Control Valves. 3L/T-2R/S33 Series Mark 70 Series.
3L/T-2R/S33 Series Mark 7 Series Sliding Gate Control Valves The Mark 7 Series is a line of pneumatically-operated diaphragm control valves that combine multiple spring actuators with the precision of
Mark 80. Self-Operated Temperature Regulators. Temperature Regulators Mark 80 Self-Operated Temperature Regulators FEATURES
Mark 80 Self-Operated Temperature Regulators The MK80 Series is completely self-operated and requires no external power source or other expensive instrumentation to operate the valve. The operation of
Mark 60 Series. Pressure Regulators Mark 60 Pressure Regulators. Self Operated Pressure Regulators. CRN Registration Number Available
Mark 60 Series Self Operated Pressure Regulators The Mark 60 Sliding Gate Pressure Regulator is used to regulate the downstream pressure to a predetermined setpoint. The spring in the Mark 60 holds the
Mark 79/79MX Series JORDANVALYE. Three-Way Control Valves
Mark 79/79MX Series Three-Way Control Valves The Mark 79 is a pneumatic 3-way control valve for use in either bypass or mixing service. The MK79 utilizes the unique sliding gate trim design to provide
Mark 37/377 Series. Control Valves Mark 37/377 Final Control Element. Final Control Element. Features
Mark 37/377 Series Final Control Element The Mark 37 is a motor-operated control valve that combines a state-of-the-art electronic linear actuator with the exceptional performance of Jordan s sliding gate
V1C Series. Pneumatic Control Valves V1C Series Cage-Guided Control Valves. Cage-Guided Control Valve. Features
V1C Series Cage-Guided Control Valve The V1C cage-guided balanced trim control valve offers high pressures and tight shutoff with the use of standard spring/diaphragm actuators. The balanced cage trim
Mark 70 Series. Sliding Gate Control Valves. Pneumatic Control Valves Mark 70 Sliding Gate Control Valves MARK 70 FEATURES
Mark 7 Series Sliding Gate Control Valves The MK7 Series is a line of pneumatically-operated diaphragm control valves that combine multiple spring actuators with the precision of Jordan Valve s advanced
Mark 75HW Series. Hand Operated Valves Mark 75 Pneumatic Control Valves. Wafer Style Hand Operated Valves. Size and Price Advantage
Mark 75HW Series Wafer Style Hand Operated Valves The Mark 75HW is a manually operated, sliding gate control valve. The wafer style body provides great value for the end user while offering all of the
708MV Series Motor Valve
708MV Series Motor Valve FRACTIONAL FLOW CONTROL S CRN Registration Number Available The Mark 708MV offers several advantages including extreme accuracy, high turndown ratios and repeatability. The features
Mark 908 Series. Pressure Regulators Mark 908X Piloted Blanketing Regulators
Pressure Regulators Mark 908X Piloted Blanketing Regulators Mark 908 Series 3/4" - 1" (DN20 - DN25) Low Pressure Blanketing (Gas overlay) PRV for medium to large Stainless and SUD vessels The Mark 908
708 Series. Fractional Flow Control Valves FRACTIONAL FLOW CONTROL VALVES. CRN Registration Number Available
708 Series Fractional Flow Control Valves FRACTIONAL FLOW CONTROL S CRN Registration Number Available The Mark 708 was developed by Jordan Valve to provide the most accurate control available for fractional
JRPH/JRPL Series. Pressure Reducing Valves. a division of Jordan Valve PRESSURE REDUCING VALVE JRPH & JRPL SERIES FLOW CONFIGURATIONS
a division of Jordan Valve JRPH/JRPL Series Pressure Reducing Valves PRESSURE REDUCING VALVE The LowFlow JRPH Series and JRPL Series are piston operated, balanced trim pressure regulators with high Cv's
Mark 5108 Series. Back Pressure Regulating Valves Mark 5108 Series. Back Pressure Regulating Valves. Valve Features. Operation
Mark 5108 Series Back Pressure Regulating Valves In many liquid piping systems, it is vital that line pressure is maintained within relatively narrow limits. The Mark 5108 is designed to do just that.
Jordan Control Valve Series
Jordan Control Valve Series JCVS Globe Style Control Valves Mark ED and ET Globe Style Control Valves The Mark ED and ET are single port, globe style bodies with composition or metal seats, and a balanced
Mark 6127 Series. Pressure Regulators Mark 6127 Series. Pressure Reducing Valves. Valve Features. Operation
Mark 6127 Series Pressure Reducing Valves The primary function of the Mark 6127 is to reduce a greater upstream pressure to a lesser, more manageable downstream pressure, operating without regard to either
Mark 75 Series. Control Valves Mark 75 Pneumatic Control Valves. Wafer Style Control Valves. Pricing Advantage. Weight Advantage
Mark 75 Series Wafer Style Control Valves The Mark 75 wafer style control valve was developed by Jordan Valve as the next generation of control valves. Featuring all the benefits of the time-tested Sliding
1/4" JRPH/JRPL Series
1/4" JRPH/JRPL Series Pressure Reducing Valves PRESSURE REDUCING VALVES The 1/4" LowFlow JRPH Series and JRPL Series are piston operated pressure regulators that offer excellent control at Cv's of 0.20
Control Valves & Regulators
Control Valves & Regulators Sliding Gate Valves Pressure Regulators Temperature Regulators Control Valves Positioners Jordan Valve sliding gate regulators and control valves are excellent choices for many
High Capacity Direct Operated Pressure Reducing Valve. Features
MK608UBAN Series High Capacity Direct Operated Pressure Reducing Valve The MK608UBAN series are spring loaded, direct-operated, pressure reducing regulators. Their main function is to regulate the outlet
MK608MM Series. Pressure Regulators Mark 608MM Self-Operated Pressure Regulator. Self-Operated Pressure Reducing Valve. Features
MK608MM Series Self-Operated Pressure Reducing Valve The MK608MM series is a spring loaded, self actuated, direct-operated valve. They are available in 1 up to 10 inches (DN25 through DN250) body sizes.
MK508UBS Series. Back Pressure Regulator MK508UBS. Threaded or Flanged Connections Carbon Steel, Stainless Steel & Alloy Construction.
MK508UBS Series Threaded or Flanged Connections Carbon Steel, Stainless Steel & Alloy Construction The MK508UBS Series are spring loaded, direct-operated, pressure relief valves used downstream of pressure
MK508MM Series. Back Pressure Regulators Mark 508MM Self-Operated Back Pressure Regulators. Self-Operated Back Pressure Regulators.
MK508MM Series Self-Operated Back Pressure Regulators The MK508MM series are spring loaded, self actuated, direct-operated valves. The Mark 508MM Back Pressure Regulating Valves regulate upstream pressure
Direct-operated, Back Pressure Regulating Valve. Features
MK508BPM Series Direct-operated, Back Pressure Regulating Valve The MK508BPM series are spring loaded, self actuated, direct-operated, valves. Pressure relief valves are used to protect the system from
VALFONTA PRESSURE REGULATOR WITHOUT AUXILIARY ENERGY EXCESS PRESSURE VALVE (PRESSURE RELIEF VALVE) MODEL S1 MAIN CHARACTERISTICS
PRESSURE REGULATOR WITHOUT AUXILIARY ENERGY EXCESS PRESSURE VALVE (PRESSURE RELIEF VALVE) MODEL S1 MAIN CHARACTERISTICS The S1 model is self-operated bellows sealed pressure excess valve. This series of
T205 Series Tank Blanketing Regulators
T205 Series Tank Blanketing Regulators Bulletin 74.1:T205 September 2013 Figure 1. Type T205 Tank Blanketing Regulator Contents Features...1 Introduction...2 Specifi cations...2 Principle of Operation...2
JB Series. Gas Back Pressure Reducing Valves BACK PRESSURE REDUCING VALVE
JB Series Gas Back Pressure Reducing Valves BACK PRESSURE REDUCING VALVE The LowFlow JB Series line of back pressure regulators have the ability to handle very high pressures and very low flows. These
VALFONTA SELF-ACTING PRESSURE REDUCING VALVE M1
SELF-ACTING PRESSURE REDUCING VALVE M1 M1-15A-ENG PRESSURE REDUCING VALVE MODEL M1 VALFONTA MAIN CHARACTERISTICS The M1 model is self-operated bellows sealed pressure reducing valve. This series of regulators
T205 Series Tank Blanketing Regulators
Bulletin 74.1 D103747X012 T205 Series June 2018 T205 Series Tank Blanketing Regulators Figure 1. Type T205 Tank Blanketing Regulator Contents Features... 1 Introduction.... 1 Specifications... 2 Principle
F300 Pressure Regulator
F300 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges P302 has Internal Relief Valve for Overpressure Protection Ideal for Fix Factor Billing The F300 series pilot operated
T200 Pressure Regulator
T200 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges T202 has internal relief valve for overpressure protection The T200 series pressure regulator is a manual, direct acting,
UNIWORLD series PNEUMATIC VALVES
UNIWORLD series PNEUMATIC VALVES 5100AD/E 07 2013 SINGLE SEAT TWO WAY ON-OFF VALVES PED 97/23/CE / ATEX 94/9/CE / MACHINERY DIRECTIVE 2006/42/CE TYPE 5100 AD Normally open air closes Face-to-face ASME
"Send a signal not a technician" Mark 95AA and Mark 95AAFT upgrade kits available for currently istalled MK95 regula- tors Air Loading a MK95AA:
Mark 95 Series Sanitary ir ugmented Back Pressure Regulators The Mark 95 with air augmentation () option offers the same line sizes, Cv choices, seats, low build up characteristics, and stability of the
Marwin Valve 4700 Series 2000 WOG Three Piece Ball Valves
4700 Series 2000 WO Three Piece Ball Valves Fire Tested API 607 4 th ed. APPROVEDDD The new Marwin 4700 Series represents the leading technology in three piece ball valves. This versatile 2000 WO rated
Exploded view 3 piece ball valves Series R
Exploded view 3 piece ball valves Series R Ball valve of series R with reduced bore (standard version) DN10 to DN65 Example shown: Series R DN65 Please follow assembly and maintenance instructions carefully.
Product overview. Technical data
VALVES & CONTROLS ANDERSON GREENWOOD BLANKETING SYSTEMS The Complete Blanketing and Safety Valve System! Product overview Pad Valves Anderson Greenwood is a world leader in tank protection and blanketing.
HELYON PRESSURE REDUCING VALVE MODEL M1
PRESSURE REDUCING VALVE MODEL - 5 Chemin du Jubin 69570 DARDILLY MAIN CHARACTERISTICS The model is self-operated bellows sealed pressure reducing valve. This series of regulators is suitable for steam,
Type MR108 Direct-Operated Backpressure Regulators
July 2016 Type MR108 Direct-Operated Backpressure Regulators P1202_1 P1203_1 Type mr108 with low-pressure Actuator Type mr108 with high-pressure actuator Figure 1. Type MR108 Direct-Operated Backpressure
ANDERSON GREENWOOD. Flow Control. Anderson Greenwood Tank and Equipment Blanketing Systems. Pad Valves. De-Pad Valves. Total Flow Control Solutions
ANDERSON GREENWOOD The Complete Blanketing and Safety Valve System! Anderson Greenwood is truly the world leader in tank protection and blanketing. Anderson Greenwood has the experience and products to
P200 Pressure Regulator
P200 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges P202 has internal relief valve for overpressure protection The P200 series pressure regulator is a manual, direct acting,
JSRLP Series Low Pressure Reducing Valves for Bio-Pharm Gas Applications
JSRLP Series Low Pressure Reducing Valves for Bio-Pharm Gas Applications JSRLP is a high purity gas low pressure regulator designed and built specifically for hygienic, ASME BPE gas applications. The JSRLP
Built-in Slam-Shut Valve. Independent pneumatic control Accuracy class: ±5% Response time: 1 second. 1/2, 11/16, and 3/4-inch (13, 18, and 19 mm)
RP Series Regulators Introduction The RP Series regulators are direct-operated with non-balanced trim. Normally they are fitted with a built-in filter. They are produced in the following versions: Types
Mark 95 Series. Sanitary Valves Mark 95 Sanitary Back Pressure Regulators. Sanitary Back Pressure Regulators
Mark 95 Series CRN Registration Number vailable Sanitary Back Pressure Regulators The Mark 95 is available with a hard or soft seat and a variety of diaphragm and o-ring materials, making the valve well-suited
F200 Pilot Operated Pressure Regulator
F200 Pilot Operated Pressure Regulator External or Internal Pressure Registration Minimize Sudden Downstream Load Change Ideal for Fix Factor Billing Quick Response Time / High ccuracy The F200 series
Manual & Automated Ball Valves
Manual & Automated Ball Valves Fire Safe Valves Metal Seated Valves Three Way Valves Automated Valves Standard Service Three Piece Ball Valves Product Matrix for Marwin Valves Model 9000 Series DM9000
P200 Pressure Regulator
P200 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges P202 has internal relief valve for overpressure protection The P200 series pressure regulator is a manual, direct acting,
SVC/SHC Series. Sanitary Check Valves. NEW - SVC for vertical down process outflow and drain installations. Features
SVC/SHC Series Sanitary Check Valves NEW - SVC for vertical down process outflow and drain installations The patented SVC/SHC Series are vertical and horizontal check valves designed specifically for use
Manual & Automated Ball Valves
Manual & Automated Ball Valves Fire Safe Valves Metal Seated Valves Three Way Valves Automated Valves Standard Service Three Piece Ball Valves Product Matrix for Marwin Valves Model 4600 Series 8700 Series
P200 Pressure Regulator
P200 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges P202 has internal relief valve for overpressure protection The P200 series pressure regulator is a manual, direct acting,
Model 5400 / 5450 Control Valve
Model 5400 / 5450 Control Valve The Model 5400 (Figure ) and Model 5450 (Figure 2) control valves are designed to meet the high pressure and erosive applications common to the oil and gas industry. These
Mark 75PTP Series JORDANVALVE. Piston Operated Wafer Style Control Valves. CRN Registration Number Available
Mark 75PTP Series CRN Registration Number Available Piston Operated Wafer Style Control Valves The Mark 75PTP is a Mark 75 wafer style control valve with an 80mm (1" - 2"} Stainless Steel Piston Actuator.
CV3000 Series. Control Ball Valve 4000 psi WOG (276 bar) Fully Customizable Flow Control Inserts Carbon, Stainless, Alloy Bar Stock Construction
4 psi WOG (276 bar) CV3 Series CV3F-xxx Series Full Port Valve CV3R-xxx Series Reduced Port Valve Features Uni-directional control valve Zero leakage shutoff, soft seated Upstream Cv plate control element
Special Kv available. Classification according pressure equipment Directive, 2014/68/UE
SELF-OPERATED PRESSURE REGULATORS PRESSURE REDUCING VALVE MODEL PRV45 PRODUCT FEATURES Self-actuating pressure reducing valve balancing by diaphragm used to provide a constant downstream still there being
JSRLF Series. Sanitary Valves JSRLF Series Low Flow Gas Reducing Valves
JSRLF Series Low Flow Pressure Reducing Valves for Bio, Pharma and High Purity Gas pplication The Steriflow JSRLF Series line of low flow pressure regulators have the ability to handle very high pressures
LVG SERIES. Gas Limiting Orifice Valve. Features. Benefits. Combustion Excellence Since 1888 LVG-1
Gas Limiting Orifice Valve Features Precision machined valve flow piston Rugged cast iron body Replaceable cartridge assembly for LVG 55-5 Straight through valve design; right angle valve option Pressure
THE SLIDING GATE SEAT: A BETTER DESIGN
PRODUCT OVERVIEW THE SLIDING GATE SEAT: A BETTER DESIGN SIMPLE CONCEPT, SUPERIOR PERFORMANCE You will notice something different in a Jordan valve... the sliding gate seat. A remarkably simple concept
THE SLIDING GATE SEAT: A BETTER DESIGN
PRODUCT OVERVIEW THE SLIDING GATE SEAT: A BETTER DESIGN SIMPLE CONCEPT, SUPERIOR PERFORMANCE You will notice something different in a Jordan valve... the sliding gate seat. A remarkably simple concept
10000F Series. High Pressure Ball Valve 6000 psi WOG (414 bar) Multiple End Connections Carbon, Stainless. Alloy Bar Stock Construction
1F-xxx Series Valve Quick Spec Product Scope Size Range 1/4" 2", (Sch 16 Pipe Bore) 2"Reduced; 3" Double Reduced Body Type 3-pc, non Swing-out design, Optional Ends Pressure Rating up to 6 psi WOG & up
JSRHF Series. Sanitary Valves JSRHF Series High Flow Pressure Reducing Valves. High Flow Bioprocess Clean Gas Pressure Reducing Valves
JSRHF Series High Flow Bioprocess Clean Gas Pressure Reducing Valves The JSRHF Series high purity gas pressure regulator was designed and built specifically for Bio-Pharma gas applications. Traditionally,
Angle Seat Valve /2" up to 3"
1/ up to up to 428 F Pneumatically operated angle seat valve for the control of neutral and aggressive gases, liquids and steam. Compact design For temperatures from -22 F up to +428 F Working pressure
Mark 978 Series STERIFLOW. Sanitary Control Valve. Sanitary Valves Mark 978 Globe-Style Control Valve AVAILABLE FINISHES FEATURES APPLICATIONS
Mark 978 Series Sanitary Control Valve The Mark 978 Sanitary Control Valve Series is designed to meet the required specifications for sterile process control valves. The MK978 Series is suitable for a
Model 5400 / 5450 Control Valve
Model 5400 / 5450 Control Valve The Model 5400 (open yoke) and Model 5450 (closecoupled) control valves are designed to meet the high pressure and erosive applications common to the oil and gas industry.
Type T205B Balanced Tank Blanketing Regulator
April 2014 Type T205B Balanced Tank Blanketing Regulator Figure 1. Type T205B Balanced Tank Blanketing Regulator Contents Introduction...2 Specifications...2 Features...3 Principle of Operation...3 Installation...4
Series 240 Pneumatic On-off Valve Type 3351
Series 240 Pneumatic On-off Valve Type 3351 Application Control valve with a tight shutoff of liquids, gases and steam in accordance with DIN or ANSI standards Nominal sizes DN 15 to 100 NPS ½ to 4 Nominal
* Contact your sales representative for compliance to NACE MR or later requirements.
VALVES & CONTROLS crosby SERIES 800, 900 OMNI-TRIM, AND BP OMNI-TRIM Crosby s Series 800 adjustable blowdown, Series 900 fixed blowdown OMNI-TRIM, and BP OMNI-TRIM full nozzle pressure relief valves have
NON-RETURN VALVE RT25
NON-RETURN VALVE RT25 DESCRIPTION The RT25 all stainless steel disc check valve has a compact design and was specially designed for use with steam and hot condensate. Connections are female screwed MAIN
Ideal Installation. I & M Mark 67 (1/2 6 ) Control Line. Installation & Maintenance Instructions for Mark 67 Pressure Regulators
I & M Mark (/ ) 0 Wasson Road Cincinnati, OH 0 USA Phone --00 Fax -8-00 info@richardsind.com www.jordanvalve.com Installation & Maintenance Instructions for Mark Pressure Regulators Warning: Jordan Valve
BUTTERFLY VALVE 17 SERIES Gearbox
DN H1 H2 H3 BUTTERFLY VALVE 17 SERIES Gearbox FIGURE: 17234ER: 17234BR: 17234VR: Seat in EPDM, with gearbox Seat in Buna, with gearbox Seat in Viton, with gearbox B ØR L DIMENSIONS: (mm) DN L B XR H1 H2
3L/T-2P/Q33 Series 3 Way Ball Valves
3L/T-P/Q33 Series 3 Way Ball Valves A multi-port valve that will lower overall costs by allowing the replacement of two or three conventional straight-line valves, eliminating excess fittings and simplifying
cs200 series commercial / Industrial pressure reducing regulators
November 2013 cs200 series commercial / Industrial pressure reducing regulators P1188 Figure 1. Typical CS200 Series Pressure Reducing Regulator Features and Benefits Wide Range of Body Sizes and End Connections
Sanitary Valves JSB Series Back Pressure Valves
3L/T-2R/S33 Series JS Series Compact, High Purity ack Pressure Regulating Valve J-Pure is the first fully drainable compact back pressure regulator designed and built specifically for hygienic, ASME PE
JSRHF Series. Sanitary Valves JSRHF Series High Flow Pressure Reducing Valves. High Flow Bioprocess Clean Gas Pressure Reducing Valves
JSRHF Series High Flow Bioprocess Clean Gas Pressure Reducing Valves The JSRHF Series high purity gas pressure regulator was designed and built specifically for Bio-Pharma gas applications. Traditionally,
Type MR108 Direct-Operated Backpressure Regulators
August 2013 Type MR108 Direct-Operated Backpressure Regulators P1202 P1203 TYPE MR108 WITH LOW- ACTUATOR TYPE MR108 WITH HIGH- ACTUATOR Figure 1. Type MR108 Direct-Operated Backpressure Regulators Contents
butterfly valves high performance Ruamcharoen Engineering And Supplies Ltp., Tel : Fax :
high performance EXECUTION OFFSET FROM CENTRE OF VALVE OFFSET FROM CENTRE OF SEAT VALVE CENTRE LINE SHAFT CENTRE LINE Valve body is solid, heavy duty. Seat Retainer construction allows Gasket conforming
Paramax Series Control Ball Valve. Specification Data CM6004 7/97
Paramax Control Ball Valve Specification Data CM6004 7/97 Table of Contents Numbering System........................ 3 Specifications............................ 4 Seal Ring Limitations......................
F200 Pilot Operated Pressure Regulator
F00 Pilot Operated Pressure Regulator External or Internal Pressure Registration Minimize Sudden ownstream Load Change Ideal for Fix Factor Billing Quick Response Time / High ccuracy The F00 series is
DBOY Series Pneumatic Control Valve
Applications Process control systems for food, pulp and paper, chemical, petrochemical & other industries HVAC systems Feed water and fuel system controls in boiler rooms Packaged systems (OEM) such as
3000F Series. Full Port 2-Way 3-pc Body
Up to 4 psi WOG (275 bar) 3F Series 3F-xxx Series Valve Features Up to 4 psi service Special barstock body material options including Alloy 2, Duplex, Hastelloy C, Monel, Titanium, 254 SMO, Bronze and
JSBLF Series Compact, High Purity Low Flow Back Pressure Regulating Valve
JSBLF Series Compact, High Purity Low Flow Back Pressure Regulating Valve The JSBLF is a fully drainable compact back pressure regulator designed and built specifically for hygienic, ASME BPE low flow
ABOUT US. LOWFLOW VALVE 3170 Wasson Road Cincinnati, OH USA LowFlowValve.com
Fractional Flow Control Valves Heavy Duty Control Valves (DN8 - DN50) Pressure Regulators Back Pressure Regulators Piston Operated Pressure Regulators Diaphragm-Sensed Pressure Regulators High Pressure
ABOUT US. LOWFLOW VALVE 3170 Wasson Road Cincinnati, OH USA LowFlowValve.com
Fractional Flow Control Valves Heavy Duty Control Valves (1/4" - 2") Pressure Regulators Back Pressure Regulators Piston Operated Pressure Regulators Diaphragm-Sensed Pressure Regulators High Pressure
627 Series Pressure Reducing Regulators
627 Series Pressure Reducing Regulators Introduction The 627 Series direct-operated reducing regulators (Figure 1) are for low and high systems. These regulators can be used with natural gas, air, or a
KOSO HAMMEL DAHL. Specifications. Body Size: Globe - 1/2" through 6" ( mm). Angle - 1/2" through 2" (15-50 mm).
control valves KOSO HAMMEL DAHL B U L L E T I N G 1 3 0-1 FEATURES Cage-retained quick change seat ring simplifies maintenance. Metal seats for a variety of services and ANSI IV and V shutoff. Soft seat
627 Series Pressure Reducing Regulators
627 Series Pressure Reducing Regulators Introduction The 627 Series direct-operated pressure reducing regulators (Figure 1) are for low and high pressure systems. These regulators can be used with natural
KEYSTONE FIGURES 310/312 K-LOK BUTTERFLY VALVES
310 - Wafer high performance butterfly valve 312 - Lugged high performance butterfly valve FEATURES GENERAL APPLICATION High performance applications such as steam, chill water, water, utility lines, gasoline,
JSRLF Series. Low Flow Pressure Reducing Valves for Bio, Pharma and High Purity Gas Application
JSRLF Series Low Flow Pressure Reducing Valves for Bio, Pharma and High Purity Gas Application New Option! EPDM seat for low lockup and tight shutoff on no flow or deadhead blanketing applications The
* Contact your sales representative for compliance to NACE MR or later requirements.
VALVES & CONTROLS crosby SERIES 00, 00 OMNI-TRIM, AND BP OMNI-TRIM Crosby s Series 00 adjustable blowdown, Series 00 fixed blowdown OMNI-TRIM, and BP OMNI-TRIM full nozzle pressure relief valves have a
627 Series Pressure Reducing Regulators
627 Series Pressure Reducing Regulators Introduction The 627 Series direct-operated pressure reducing regulators (Figure 1) are for low and high-pressure systems. These regulators can be used with natural
Fabricated Bevel Gear Operator Bi-Directional Metal Seat 150 PSI Bi-Directional Resilient Seat 150 PSI
Knife Gate Valves Uni-Directional (Metal Seated) Manual Handwheel Style KGV...2 Carbon Steel Technical Data 150 PSI 2 24...3 304 Stainless Steel Technical Data 150 PSI 2 24...3 316 Stainless Steel Technical
CP400 Series Commercial/Industrial Pressure Loaded Pressure Reducing Regulators
CP400 Series Commercial/Industrial Pressure Loaded Pressure Reducing Regulators September 2014 P1182 typical type cp400 regulator P1522 P1410 Typical type CP403 Regulator WITH INTEGRAL TRUE-MONITOR PROTECTION
Series 240 Type 3351 Pneumatic On/off Valve
Series 240 Type 3351 Pneumatic On/off Valve Application Shut-off valve with tight shut-off for liquids, gases and vapors according to DIN or ANSI standards Valve size DN 15 to 100 NPS ½ to 4 Pressure rating