TABLE OF CONTENTS 3 VALVE SEATS PROGRESSIVE LISTING BY OUTSIDE DIAMETER ENGINE HARDWARE GENERAL APPLICATION DATA - 56

Transcription

1 A COMPANY

2 TABLE OF CONTENTS SECTION 1 INTRODUCTION TABLE OF CONTENTS PAGE - I 2 BEARINGS/ BUSHINGS GENERAL APPLICATION DATA 1-10 SET CONTENTS SPECIALTY SET LISTING SPECIALTY COMPONENT LISTING - 17 HI-PERFORMANCE VALVE SEATS PROGRESSIVE LISTING BY OUTSIDE DIAMETER ENGINE HARDWARE GENERAL APPLICATION DATA ENGINE HARDWARE FINISHING KITS - 57 GENERAL APPLICATION DATA VALVE SPRING BOOSTER SHIMS - 59 NUMERICAL LISTING - 60 PROGRESSIVE LISTING BY OUTSIDE DIAMETER - 61 PROGRESSIVE LISTING BY INSIDE DIAMETER CONVERSION REFERENCE CHART - 63 DISCLAIMER Although the information in this supplement has been gathered from the best available sources and every possible effort has been made to ensure accuracy, we cannot accept responsibility for any errors or omissions. We would very much appreciate being advised of any inaccuracies which might come to your attention. Dura-Bond reserves the right to update and change product specifications at any time without notice. This supplement contains parts information only. Before installing any part listed, consult the appropriate vehicle manufacturer's instructional manual for detailed installation instructions. WARRANTY Dura-Bond Bearing Company products are warranted to be free from defects of materials or workmanship for one year from the date of purchase. Dura-Bond Bearing Company's responsibility is limited to the replacement value of the product if Dura-Bond determines the product to be defective under normal use and service. Claims for labor or related component cost will not be considered. No other warranty, either expressed or implied, is made. Be sure to check us out online at for the latest additions. If you have a product need, we invite you to inquire. Check with us regarding all of your sleeve bearings, valve seats, and shim needs. *TRANSMISSION PIECES *MOTORCYCLES *MARINE APPLICATIONS *INDUSTRIAL APPLICATIONS *ANTIQUE VEHICLES *BUSHINGS Copywriter, Editor, Design Layout - William Dolak 2007 DURA-BOND BEARING COMPANY ALL RIGHTS RESERVED. NO PORTION OF THIS SUPPLEMENT MAY BE REPRODUCED WITHOUT OUR EXPRESS WRITTEN PERMISSION. I

3 CAMSHAFT BEARINGS DISPLACEMENT GENERAL APPLICATION DATA CAMSHAFT BEARING SET CYL. CU. IN. L BORE YEAR (ENG SERIES/MAKE/MODEL) STD. HI-PERF. OHC AMERICAN MOTORS 4 cyl 151ci 2.5L OHV PONTIAC R eng. AMX, Concord, Eagle, CH-16 Kammback, SX-4, Spirit (.001 under ID) CH-16W CATERPILLAR 6 cyl 403ci 6.6L Caterpillar Series 3116 CAT-5 6 cyl 638ci 10.5L Caterpillar Series 3306 (5 Bearing set) CAT-6 6 cyl 638ci 10.5L Caterpillar Series 3306 (3 Bearing set) CAT-7 CHECKER MOTORS CORP. 6 cyl 250ci 4.1L Chevrolet D Series Eng. (Late Models) CH-11 (Special oil control set w OD groove) CH-11B 8 cyl 267ci 4.4L Chevrolet J Series Eng. CH-8 CHP-8 CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 283ci 4.6L Chevrolet (includes C Series) Eng. CH-8 CHP-8 CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 305ci 5.0L Chevrolet H, U Series Eng. CH-8 CHP-8 CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 307ci 5.0L Chevrolet A Series Eng. CH-8 CHP-8 CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W *Denotes half shell bearings **Denotes balance shaft bearings 1

4 CAMSHAFT BEARINGS DISPLACEMENT GENERAL APPLICATION DATA CAMSHAFT BEARING SET CYL. CU. IN. L BORE YEAR (ENG SERIES/MAKE/MODEL) STD. HI-PERF. OHC CHECKER MOTORS CORP. (CONT'D) 8 cyl 327ci 5.3L Chevrolet Eng. CH-8 CHP-8 CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 350ci 5.7L Chevrolet (includes L Series) Eng. CH-8 CHP-8 CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W CHRYSLER 8 cyl 287ci 4.7L SOHC Chrysler PDA-4* 8 cyl 345ci 5.7L Hemi PD-31B 8 cyl 370ci 6.1L Hemi PD-31B DETROIT DIESEL 2 cyl 106ci 1.7L Detroit Diesel 2-53, 2-53N DE-2** (Camshaft brg & balance shaft bushing set, 5 pcs) (+.010 O.D.) DE-2R1** 3 cyl 159ci 2.6L Detroit Diesel 3-53,3-53N DE-2A** (Camshaft brg & balance shaft bushing set, 6 pcs) (+.010 O.D.) DE-2AR1** FORD MOTOR CO. 6 cyl 244ci 4.0L SOHC Ford Explorer, Mountaineer FA-6* 8 cyl 365ci 6.0L International Diesel IN-21 8 cyl 370ci 6.1L OHV Ford V-8 Eng. Ford MD & HD Truck/Van: 600- F-30 FP-30 or 900 Series FP-30T (+.005 O.D.) FP-30R (+.010 O.D.) F-30R1 (+.020 O.D.) F-30R2 6 cyl 401ci 6.6L OHV Ford Turbo-Diesel F-55 8 cyl 429ci 7.0L OHV Ford V-8 Vin Series J - R Eng. Ford, Mercury F-30 FP-30 or Passenger Cars & Hi Perf. Ford HD Truck: FP-30T Series (+.005 O.D.) FP-30R (+.010 O.D.) F-30R1 (+.020 O.D.) F-30R2 *Denotes half shell bearings **Denotes balance shaft bearings 2

5 CAMSHAFT BEARINGS DISPLACEMENT GENERAL APPLICATION DATA CAMSHAFT BEARING SET CYL. CU. IN. L BORE YEAR (ENG SERIES/MAKE/MODEL) STD. HI-PERF. OHC FORD MOTOR CO. (CONT'D) 8 cyl 460ci 7.5L OHV Ford V-8 Vin Series A, C, G, J, L Eng. Ford, F-30 FP-30 or Mercury, Lincoln incl. Continental, Cougar, Galaxie FP-30T LTD, Mark Series, Marquis, Monterey, T-Bird, Torino Ford Truck/Van: E , F , F (Super Duty) (+.005 O.D.) FP-30R (+.010 O.D.) F-30R1 (+.020 O.D.) F-30R2 6 cyl 474ci 7.8L OHV Ford Turbo-Diesel F-55 GENERAL MOTORS Includes truck (Chevrolet, GMC, Oldsmobile, & Pontiac) and passenger cars (Buick, Cadillac, Chevrolet, Geo, Oldsmobile, Pontiac, & Saturn) 4 cyl 134ci 2.2L Saturn (Balance shaft set) CHG-24** 4 cyl 151ci 2.5L OHV Pontiac Type R, 2 Engs. Buick, Chevrolet, Olds, CH-16 Pontiac Passenger Cars OHV Pontiac Type A, E Engs. Chevrolet/GMC Truck: S-10, GMC S-15 (.001 under ID) CH-16W 4 cyl 170ci 2.8L (Balance shaft set) CHG-23** 6 cyl 173ci 2.8L OHV Chevrolet V-6 Type LL2 Eng. GM A, N, J, X body CH-18 (89mm) incl. Century, Celebrity, Camaro, Citation, Astre, Fiero, 6000, Lumina. Chev/GMC Truck & Van: Blazer, S-10, Jimmy, S-15, Sonoma (Special brg set w wide #2 & 3 pos.) CH-18A (Oversize OD) CH-18RS (Oversize OD) CH-18R8 4 cyl 181ci 3.0L OHV GM Eng. (Marine & Industrial) CH-16 (.001 under ID) CH-16W 6 cyl 189ci 3.1L OHV Chev V-6 incl. Types D,M, T, W (88-95), Type V CH-18 (89mm) incl. Turbo (89-90). Buick, Chevrolet, Olds, Pontiac Pass. Cars (Special brg set w wide #2 & 3 pos.) CH-18A (Oversize OD) CH-18RS (Oversize OD) CH-18R8 6 cyl 207ci 3.4L DOHC Chevrolet V-6 Type X Eng. CH-18 (92mm) Chev Lumina & Mini-Van, Monte Carlo, Venture OHV Chevrolet V-6 Type E, S Eng. Chevrolet Camaro, Monte Carlo; Pontiac Firebird (Special brg set w wide #2 & 3 pos.) CH-18A (Oversize OD) CH-18RS (Oversize OD) CH-18R8 5 cyl 213ci 3.5L (Balance shaft set) CHG-23** 6 cyl 212ci 3.5L Olds (Balance shaft set) OG-1** 6 cyl 250ci 4.1L OHV Chevrolet Eng. (incl. Mexico) Buick, Chevrolet, CH-11 Olds., Pontiac Passenger Cars, Chevrolet/GMC LT. Truck & Van: Series (Special oil control set w/ O.D. groove) CH-11B *Denotes half shell bearings **Denotes balance shaft bearings 3

6 CAMSHAFT BEARINGS DISPLACEMENT GENERAL APPLICATION DATA CAMSHAFT BEARING SET CYL. CU. IN. L BORE YEAR (ENG SERIES/MAKE/MODEL) STD. HI-PERF. OHC GENERAL MOTORS (CONT'D) 6 cyl 262ci 4.3L OHV Chevrolet V-6 LB4, LF6-Hi Output Type B, N, W, CH-17 CHP-17 or X, Z incl H.O., Turbo (91-93) Eng. CHP-17T Chev/GMC Truck & Van: S-10, Blazer, Jimmy, Safari, Sierra, El Camino, Series (Balance shaft rear brg., includes tool) CHG-15A** (Cam bearing and balance shaft bearing kit) CH-17G OHV Chevrolet V-6 LB4, LF6-Hi Output Type T Eng, CH-21 (I.D.# starting w "T" located on front of block). Same applications above (Balance shaft rear brg., includes tool) CHG-15A** (Cam bearing and balance shaft bearing kit) CH-21G 8 cyl 262ci 4.3L OHV Chevrolet V-8 Type G Eng. Chevrolet Monza, CH-8 CHP-8 or Nova CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 265ci 4.3L OHV Chevrolet V-8 Type W Eng. Chevrolet Caprice. CH-8 CHP-8 or CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 267ci 4.4L OHV Chevrolet V-8 Type J Eng. Buick, Chevrolet, CH-8 CHP-8 or Olds, Pontiac Passenger Cars. Chev/GMC Truck: CHP-8T Caballero, El Camino. Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 283ci 4.6L OHV Chevrolet V-8 Eng. U.S. & Canada mfg. Chev. CH-8 CHP-8 or Full Size, Nomad, Camaro, Chevy II, Chevelle, Corvette. CHP-8T Chev/GMC Truck & Van: 10-80, Series Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 6 cyl 292ci 4.8L OHV Chevrolet 6 cyl Type T Eng. Chev/GMC Truck: CH-11 Blazer, Jimmy, Suburban, 10-60, Series (Special oil control set w/ O.D. groove) CH-11B *Denotes half shell bearings **Denotes balance shaft bearings 4

7 CAMSHAFT BEARINGS DISPLACEMENT GENERAL APPLICATION DATA CAMSHAFT BEARING SET CYL. CU. IN. L BORE YEAR (ENG SERIES/MAKE/MODEL) STD. HI-PERF. OHC GENERAL MOTORS (CONT'D) 8 cyl 305ci 5.0L OHV Chevrolet V-8 Type E-H, Q, M, S, U, X Eng. CH-8 CHP-8 or Buick Full Size, Skylark; Chev. Full Size, Camaro, CHP-8T Chevelle, Corvette, Nova; Olds Full Size; Pontiac Full Size, Firebird, Grand Am, Grand Prix, Phoenix, Sunbird, Ventura; Chev/GMC Truck & Van: Blazer, El Camino, Jimmy, Suburban, Tahoe, Yukon, Series Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 307ci 5.0L OHV Chevrolet V-8 Type A, F Eng. Chev. Full Size, CH-8 CHP-8 or Camaro, Chevelle, Nova; Pontiac Ventura, T-37 CHP-8T Chev/GMC Truck/Van: Blazer, El Camino, Jimmy, Sprint, Series Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 327ci 5.3L OHV Chevrolet V-8 Eng. Same as above including CH-8 CHP-8 or Camaro, El Camino, Sprint & Hi Perf. CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 346ci 5.7L OHV Chevrolet LS-1 2nd Series Mark III V-8 Vin Type G CH-23 CHP-23 or (Pass. Cars), R (Truck) Eng. Chevrolet Corvette, CHP-23T Chevrolet/GMC Truck 8 cyl 350ci 5.7L OHV Chevrolet V-8 Vin Type G, H, K, L, M, P, R, T, V, CH-8 CHP-8 or X, Y, 4, 6, 7, 8 Engs. incl. Hi Perf, Vortex & Aluminum CHP-8T blocks except DOHC Eng. Chevrolet & Hi-Perf, Buick, Cadillac, Olds, Pontiac Passenger Cars. Chev/GMC Truck & Van: Blazer, Jimmy, El Camino, Suburban, Yukon & S.U.V's, Series Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W *Denotes half shell bearings **Denotes balance shaft bearings 5

8 CAMSHAFT BEARINGS DISPLACEMENT GENERAL APPLICATION DATA CAMSHAFT BEARING SET CYL. CU. IN. L BORE YEAR (ENG SERIES/MAKE/MODEL) STD. HI-PERF. OHC GENERAL MOTORS (CONT'D) 8 cyl 366ci 6.0L OHV Chevrolet V-8 Type E, L Eng. Chev/GMC Truck & CH-12 CHP-12 or Van: 40-80; Series CHP-12T (Special oil control set w/ O.D. groove) CH-12B (+.010 O.D., hsg.) CHP-12R1 (+.020 O.D., hsg.) CHP-12R2 8 cyl 379ci 6.2L OHV GM Diesel V-8 Type C, J Eng. Chev/GMC Truck GM-7 & Van: Sierra, Suburban, Yukon, 10-30; Series (+.020 O.D.) GM-7R2 8 cyl 395ci 6.5L OHV GM Diesel/Turbo Diesel V-8 Type F, P, S, Y Eng. GM-7 Chev/GMC Truck & Van: Blazer, Jimmy, Express, Savana, Sierra, Suburban, Tahoe, Yukon, 10-30; Series (+.020 O.D.) GM-7R2 8 cyl 396ci 6.5L OHV Chevrolet Big Block V-8 & Hi-Perf. Eng. Chev. CH-12 CHP-12 or Full Size, Camaro, Chevelle, Corvette, Malibu, Nova CHP-12T Chev Truck: El Camino, 10-30; Series (Special oil control set w/ O.D. groove) CH-12B (+.010 O.D., hsg.) CHP-12R1 (+.020 O.D., hsg.) CHP-12R2 8 cyl 400ci 6.6L OHV Chevrolet 400 Small Block V-8 & Hi-Perf. Eng. CH-8 CHP-8 or Chev. Full Size, Chevelle Malibu, Monte Carlo CHP-8T Chev/GMC Truck & Van: Blazer, El Camino, Jimmy, Sprint, Suburban, 10-30; Series Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 402ci 6.6L OHV Chevrolet Big Block V-8 & Hi-Perf. Eng. Chev. CH-12 CHP-12 or Full Size, Camaro, Chevelle Malibu, Monte Carlo, Nova CHP-12T Chev Truck: El Camino, Sprint, 10-30; Series (Special oil control set w/ O.D. groove) CH-12B (+.010 O.D., hsg.) CHP-12R1 (+.020 O.D., hsg.) CHP-12R2 8 cyl 403ci 6.6L Chevrolet Duramax Diesel, Turbo V-8 Type LB7 Eng. GM-8 GMC Truck 8 cyl 427ci 7.0L OHV Chevrolet Big Block V-8 incl. Aluminum & Hi-Perf. CH-12 CHP-12 or Eng. Chev. Full Size, Camaro, Corvette & Hi-Perf. CHP-12T Chev/GMC Truck & Van: 40-80, Series (Special oil control set w/ O.D. groove) CH-12B (+.010 O.D., hsg.) CHP-12R1 (+.020 O.D., hsg.) CHP-12R2 8 cyl 454ci 7.4L OHV Chev Big Block V-8 Vin Type J, L, N, S, V, W, Y CH-12 CHP-12 or incl. Alum. & Hi-Perf. Eng. Chev. Full Size, Chevelle, CHP-12T Corvette, Monte Carlo & Hi-Perf. Chev/GMC Truck & Van: Blazer, El Camino, Jimmy, Sierra, Sprint, Suburban, Yukon, 10-30, Series (Special oil control set w/ O.D. groove) CH-12B (+.010 O.D., hsg.) CHP-12R1 (+.020 O.D., hsg.) CHP-12R2 *Denotes half shell bearings **Denotes balance shaft bearings 6

9 CAMSHAFT BEARINGS DISPLACEMENT GENERAL APPLICATION DATA CAMSHAFT BEARING SET CYL. CU. IN. L BORE YEAR (ENG SERIES/MAKE/MODEL) STD. HI-PERF. OHC GENERAL MOTORS (CONT'D) 8 cyl 496ci 8.1L OHV Chevrolet Vortec 8100 L18 CH-12 CHP-12 or CHP-12T (Special oil control set w/ O.D. groove) CH-12B (+.010 O.D., hsg.) CHP-12R1 (+.020 O.D., hsg.) CHP-12R2 8 cyl 502ci 8.2L OHV Chev Bowtie V-8 Hi-Perf. Block w std. CH-12 CHP-12 or hsg bores. GM Hi-Perf Car & Truck CHP-12T (Special oil control set w/ O.D. groove) CH-12B (+.010 O.D., hsg.) CHP-12R1 (+.020 O.D., hsg.) CHP-12R2 HOLDEN 6 cyl ci Holden 138 Red (2250) HO-1 6 cyl ci Holden 149 Red HO-1 6 cyl ci Holden 161 Red (2650) HO-1 6 cyl ci Holden 173 Blue/Black (2850), 173 Red (2850) HO-1 6 cyl ci Holden 179 Red HO-1 6 cyl ci Holden 186 Red HO-1 6 cyl ci Holden 202 Blue/Black (3300), 202 Red (3300) HO-1 8 cyl ci Holden 253 Blue (4.2) HO-2 (+.002 O.D. #5 brg) HO-2S 8 cyl ci Holden 308 Red HO-2 (+.002 O.D. #5 brg) HO-2S IHC (NAVISTAR) TRUCK 8 cyl 365ci 6.0L International Diesel IN-21 ISUZU Also see (General Motors) 6 cyl 173ci 2.8L OHV V-6 Chevrolet Type LL2 Eng. Isuzu Trooper II CH-18 (89mm) (Special brg set w wide #2 & 3 pos.) CH-18A (Oversize OD) CH-18RS (Oversize OD) CH-18R8 6 cyl 189ci 3.1L OHV V-6 Chevrolet Type LG6, CPC Eng. Isuzu Pickup, CH-18 (89mm) Rodeo (Special brg set w wide #2 & 3 pos.) CH-18A (Oversize OD) CH-18RS (Oversize OD) CH-18R8 6 cyl 262ci 4.3L OHV Chevrolet V-6 Type LB4, LF6-Hi Output X Series CH-17 CHP-17 or Eng, (all models except T series). Isuzu Hombre, CHP-17T Truck & Industrial (Balance shaft rear brg., includes tool) CHG-15A** (Cam bearing and balance shaft bearing kit) CH-17G OHV Chevrolet V-6 LB4, LF6-Hi Output Type T Eng, CH-21 (I.D.# starting w "T" located on front of block). Same applications above (Balance shaft rear brg., includes tool) CHG-15A** (Cam bearing and balance shaft bearing kit) CH-21G *Denotes half shell bearings **Denotes balance shaft bearings 7

10 CAMSHAFT BEARINGS DISPLACEMENT GENERAL APPLICATION DATA CAMSHAFT BEARING SET CYL. CU. IN. L BORE YEAR (ENG SERIES/MAKE/MODEL) STD. HI-PERF. OHC ISUZU (CONT'D) 8 cyl 350ci 5.7L OHV Chevrolet V-8 Vin Type CPC Code G, H, K, L, M, CH-8 CHP-8 or P, R, T, V, X, Y, 4, 6, 7, 8 engs incl. Hi Perf, Vortex & CHP-8T Aluminum blocks except DOHC Eng. Isuzu Truck & Industrial Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W JEEP Also see (American Motors & Chrysler) 4 cyl 150ci 2.46L Jeep Inline 4 N-10 4 cyl 151ci 2.5L OHV Pontiac Type B Eng. Jeep CJ, DJ, Pick-up, CH-16 Scrambler (.001 under ID) CH-16W 6 cyl 173ci 2.8L OHV Chevrolet V-6 w Type LL2 Eng. Jeep CH-18 (89mm) Cherokee, Commanche, Sportwagon, Wagoneer (Special brg set w wide #2 & 3 pos.) CH-18A (Oversize OD) CH-18RS (Oversize OD) CH-18R8 6 cyl 242ci 4.0L Jeep Inline 6 N-10 MERCRUISER/MERCURY MARINE 4 cyl 224ci 3.7L Ford 470, 470R Mercruiser/Mercury Marine Eng. F-30 FP-30 or FP-30T (+.005 O.D.) FP-30R (+.010 O.D.) F-30R1 (+.020 O.D.) F-30R2 MILITARY STANDARD 3 cyl 159ci 2.6L Detroit Diesel 3-53, 3-53N Eng. Military Truck M561 DE-2A** (Camshaft brg & balance shaft bushing set, 5 pcs) (+.010 O.D.) DE-2AR1** 8 cyl 283ci 4.6L OHV Chevrolet V-8 Eng. GMC Military Truck & Van: CH-8 CHP-8 or M114A1, M116, T114 CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 302ci 5.0L OHV Chevrolet V-8 Eng. GMC Military Truck & Van: CH-8 CHP-8 or M207C CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W *Denotes half shell bearings **Denotes balance shaft bearings 8

11 CAMSHAFT BEARINGS DISPLACEMENT GENERAL APPLICATION DATA CAMSHAFT BEARING SET CYL. CU. IN. L BORE YEAR (ENG SERIES/MAKE/MODEL) STD. HI-PERF. OHC NISSAN (includes INFINITI, DATSUN) 4 cyl ci Nissan ZD30 (Balance shaft set) NIG-1** (96mm) SATURN (ALSO SEE GENERAL MOTORS) 4 cyl 134ci 2.2L Saturn (Balance shaft set) CHG-24** STUDEBAKER 8 cyl 283ci 4.6L OHV V-8 Chevrolet Eng. Studebaker Avanti, CH-8 CHP-8 or Commander, Cruiser, Daytona, Wagonaire CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W TOYOTA 4 cyl 2.2L Toyota 5SFE DOHC, 32 Tooth Gear (Balance shaft set) TOG-11** 4 cyl 2.2L Toyota 5SFE DOHC, 22 Tooth Gear (Balance shaft set) TOG-11A** 4 cyl 2.2L Toyota 5SFE DOHC, 22, 32 Tooth Gear (Balance shaft set) TOG-11C** (Combines TOG-11 and TOG-11A) VOLVO-PENTA Marine Engines 8 cyl 305ci 5.0L Volvo-Penta (Chevrolet) AQ200D, AQ225D, BB225A, CH-8 CHP-8 or BB225AV Marine Eng. CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W 8 cyl 350ci 5.7L Volvo-Penta (Chevrolet) AQ260A, AQ290D, BB260A, CH-8 CHP-8 or BB260AV Marine Eng. CHP-8T Options: (+.010 o'size, hsg,.0795 wall) CH-4A (+.010 OD, hsg) CHP-8R1 (+.020 OD, hsg) CHP-8R2 (+.030 OD, hsg) CHP-8R3 (+.040 OD, hsg) CHP-8R4 (.001 under ID) CH-8W WAUKESHA 6 cyl 330ci 5.3L Waukesha VRD330 Diesel, VRD330S Turbocharged WA-8 Diesel 6 cyl 330ci 5.3L Waukesha VRG330 CNG WA-8 6 cyl 468ci 7.6L Waukesha 140HL, 140HS WA-10 6 cyl 501ci 8.2L Waukesha V WA-11 6 cyl 525ci 8.6L Waukesha 140GK, 140GS, 140GKB, 140HK WA-10 6 cyl 554ci 9.1L Waukesha 140GZ, 140GZC, 140GZU, F554G, 140GZB WA-10 *Denotes half shell bearings **Denotes balance shaft bearings 9

12 CAMSHAFT BEARINGS DISPLACEMENT GENERAL APPLICATION DATA CAMSHAFT BEARING SET CYL. CU. IN. L BORE YEAR (ENG SERIES/MAKE/MODEL) STD. HI-PERF. OHC WAUKESHA (CONT'D) 6 cyl 638ci 10.5L Waukesha 145GS, 145HS WA-11 6 cyl 779ci 12.8L Waukesha 145GK, 145GKU, 145GKB, 145HK WA-11 6 cyl 817ci 13.4L Waukesha 145GZ, 145GZU, F817G, 145GZB WA-11 6 cyl 1013ci 16.6L Waukesha 6WAL, 6WALH WA-9 6 cyl 1196ci 19.6L Waukesha 6WAKB, 6WAKD, 6WAK, 6WAKC, 6WAKDB, WA-9 6WAKDBS, 6WAKDS, 6WAKM, F1197G, F1197GR, 6WAKH SPECIALTY AFTERMARKET BLOCKS 8 cyl NA NA NA NA Dart, Little "M" Block, (2.000 hsg bore), O.D. groove DT-1T with 3 hole, 120 degree spacing. (+.010 O.D.) DT-1TR1 8 cyl NA NA NA NA Dart, Big "M" Block, (2.120 hsg bore), O.D. groove GMP-12LT with 3 hole, 120 degree spacing. 8 cyl NA NA NA NA Dart, Iron Eagle GMP-2T 8 cyl NA NA NA NA Dart, Ford SVO Block SBF-1T (+.010 O.D.) SBF-1R1T *Denotes half shell bearings **Denotes balance shaft bearings 10

13 BEARING SET CONTENTS SET NO. ENGINE MFG. CONTENTS POSITION HOUSING BORE LENGTH MAX. WALL CAT-5 CATERPILLAR CAT std CAT-5-1 2,3,4,5,6, CAT-6 CATERPILLAR CAT std CAT-2-2 2,3,4, CAT-7 CATERPILLAR CAT std CAT-2-2 2, CH-8W GENERAL MOTORS CORP. CH-4-1W CH-4-2W 2, CH-4-3W 3, CHP-8R1 GENERAL MOTORS CORP. CHP ,2,3,4, CHP-8R1T std CHP-8R2 GENERAL MOTORS CORP. CHP ,2,3,4, CHP-8R2T std CHP-8R3 GENERAL MOTORS CORP. CHP ,2,3,4, CHP-8R3T std CHP-8R4 GENERAL MOTORS CORP. CHP ,2,3,4, CHP-8R4T std CHP-10 GENERAL MOTORS CORP. CHP , CHP-10T CHP , std CHP CH-11B GENERAL MOTORS CORP. CH-5-3B 1,2,3, std CH-12B GENERAL MOTORS CORP. CH-12-1B std CH-12-2B 2, CH-12-3B 3, CH-16W GENERAL MOTORS CORP. CH-5-3W 1,2, std CH-17G GENERAL MOTORS CORP. CH std CH-4-2 2, CH CHG SH-1798T (Tool) CH-18RS GENERAL MOTORS CORP. CH-18-1R std CH-18-2R2 2, CH-18-4R CH-18R8 GENERAL MOTORS CORP. CH-18-1R std CH-18-2R8 2, CH-18-4R CH-21G GENERAL MOTORS CORP. CH-4-1 1, std CH CH CHG SH-1798T (Tool) CH-23 GENERAL MOTORS CORP. CH , std CH , CH CHP-23 GENERAL MOTORS CORP. CHP , CHP-23T CHP , std CHP CHG-15A** GENERAL MOTORS CORP. CHG std SH-1798T (Tool) *Denotes half shell bearings **Denotes balance shaft bearings 11

14 BEARING SET CONTENTS SET NO. ENGINE MFG. CONTENTS POSITION HOUSING BORE LENGTH MAX. WALL CHG-23** GENERAL MOTORS CORP. CHG-23-1 Right Rear std CHG-23-2 Right Front CHG-23.3 Left Front CHG-23-4 Left Rear CHG-24** GENERAL MOTORS CORP. CHG ,2 (2 pcs.) std DE-2R1 DETROIT DIESEL DE-2-1R1 1,3 (4 pcs.) std DE-2-2R1 2 (1 pcs.) DE-2AR1 DETROIT DIESEL DE-2-1R1 1,3 (4 pcs.) std DE-2-2R1 2 (2 pcs.) DT-1T SPECIALTY AFTERMARKET BLOCKS DT-1-1 1,2,3,4, std DT-1TR1 SPECIALTY AFTERMARKET BLOCKS DT ,2,3,4, std F-30R1 FORD F-30-1R1 1,2,3,4, std F-30R2 FORD F-30-1R2 1,2,3,4, std F-55 FORD F ,2,3,4,5,6, std FA-6* FORD FA-6-2(U) std FA-6-4(U) 2,3, FA-6-1(L) FA-6-3(L) 2,3, GM-7R2 GENERAL MOTORS CORP. GM-7-1R std GM-7-2R2 2,3, GM GM-8 GENERAL MOTORS CORP. GM std GM-8-2 2,3,4, GMP-2T SPECIALTY AFTERMARKET BLOCKS GMP-2-1 1,2,3,4, std GMP-12LT SPECIALTY AFTERMARKET BLOCKS CH-12-3LT 1,2,3,4, std HO-1 HOLDEN HO-1-1 1,2,3, std HO-2 HOLDEN HO und HO HO HO HO HO-2S HOLDEN HO und HO HO HO HO-2-5S IN-21 IHC (NAVISTAR) IN ,2,3,4, std N-10 JEEP N std N N N NIG-1** NISSAN NIG std NIG OG-1** GENERAL MOTORS CORP. OG std *Denotes half shell bearings **Denotes balance shaft bearings 12

15 BEARING SET CONTENTS SET NO. ENGINE MFG. CONTENTS POSITION HOUSING BORE LENGTH MAX. WALL PD-31B CHRYSLER PD-31-1B std PD-31-2B PD-31-3B PD-31-4B PD-31-5B PDA-4* CHRYSLER PDA-4-2 (U) 1,2,3,4, std PDA-4-1 (L) 1,2,3,4, SBF-1T SPECIALTY AFTERMARKET BLOCKS 351-HPB std 351-HPB HPB HPB HPB SBF-1R1T SPECIALTY AFTERMARKET BLOCKS 351-HPB-1R std 351-HPB-2R HPB-3R HPB-4R HPB-5R TOG-11** TOYOTA TOG-11-1 (4 pcs.) und TOG-11-2 (4 pcs.) und TOG-11-3 (4 pcs.) TOG-11A** TOYOTA TOG-11-1 (8 pcs.) und TOG-11-3 (4 pcs.) und TOG-11C** TOG-11-1 (8 pcs.) und TOG-11-2 (4 pcs.) und TOG-11-3 (4 pcs.) WA-8 WAUKESHA WA std WA-8-2 2,3, WA-9 WAUKESHA WA std WA-9-2 2, WA WA-10 WAUKESHA WA-2-1 1,2,3, std WA-11 WAUKESHA WA ,2,3, std *Denotes half shell bearings **Denotes balance shaft bearings 13

16 SPECIALTY CAMSHAFT BEARING SETS SET NO. COMMENTS CONTENTS POSITION HOUSING BORE LENGTH MAX. WALL 351HP-R1 HP cam brg set w.010 oversize OD 351HP-1R std 351HP-2R HP-3R HP-4R HP-5R B-12B Special oil control set B-11-1B und w OD groove in #1 position B-9-2 2,3, C-4A Cam brg set w wide #5 position C std C C C C-4-5A CH-4A Cam brg set w.010 oversize OD CH-4-1S 1,2,3,4, std CH-8W Cam brg set w.001 under ID CH-4-1W CH-4-2W 2, CH-4-3W 3, CHP-8R1 Cam brg set w.010 oversize OD CHP ,2,3,4, std CHP-8R2 Cam brg set w.020 oversize OD CHP ,2,3,4, std CHP-8R3 Cam brg set w.030 oversize OD CHP ,2,3,4, std CHP-8R4 Cam brg set w.040 oversize OD CHP ,2,3,4, std CH-11B Special oil control set w OD groove CH-5-3B 1,2,3, std CH-12B Special oil control set w OD groove CH-12-1B std CH-12-2B 2, CH-12-3B 3, CHP-12R1 Cam brg set w.010 oversize OD CHP std CHP ,3,4, CHP-12R2 Cam brg set w.020 oversize OD CHP std CHP ,3,4, CH-17G Combines CH-17 and CHG-15A** CH std CH-4-2 2, CH CHG SH-1798T (Tool) CH-17X Cam brg set w.001 under ID CH-4-1W std CH-4-2W 2, CH-4-3W CH-18A Cam brg set w wide #2 & 3 position CH-18-1A und CH-18-2A 2, CH CH-18RS Cam brg set w oversize OD CH-18-1R std CH-18-2R2 2, CH-18-4R CH-18R8 Cam brg set w oversize OD CH-18-1R std CH-18-2R8 2, CH-18-4R *Denotes half shell bearings **Denotes balance shaft bearings 14

17 SPECIALTY CAMSHAFT BEARING SETS SET NO. COMMENTS CONTENTS POSITION HOUSING BORE LENGTH MAX. WALL CH-21G Combines CH-21 and CHG-15A** CH-4-1 1, std CH CH CHG SH-1798T (Tool) CH-21X Cam brg set w.001 under ID CH-4-1W 1, std CH-4-2W CH-4-3W DE-2R1** Cam brg & bal. shaft set DE-2-1R1 1,3 (4 pcs.) std w.010 oversize OD DE-2-2R1 2 (1 pcs.) DE-2AR1** Cam brg & bal. shaft set DE-2-1R1 1,3 (4 pcs.) std w.010 oversize OD DE-2-2R1 2 (2 pcs.) DT-1TR1 Cam brg set w.010 oversize OD DT ,2,3,4, std F-23B Special oil control set w OD groove F-23-1B 1,2,3, und F-30R1 Cam brg set w.010 oversize OD F-30-1R1 1,2,3,4, std F-30R2 Cam brg set w.020 oversize OD F-30-1R2 1,2,3,4, std FP-30R HP cam brg set w.005 oversized OD FP-30-1R 1,2,3,4, std F-34B Special oil control set w OD groove F-34-1B 1,2, und F-34S Cam brg set w.020 oversize OD F-34-1S 1,2,3, std F-38 Combines F-52 and FG-51 AGB , std F , F , F-38X Combines F-52X and FG-51 AGB , std w special wide #2 & #3 position F-52-1X 1, F-51-2X 2, F-47B Special oil control set w OD groove F und F-47-2B F-47-3B F F-48A Cam brg set w I.D. groove # 4 position F und F , F-48-4A F-49B Special oil control set w OD groove F-49-1B 1, und F-23-1B 2, F-50A Cam brg set w special wide #4 brg F und F und F und F-50-4A GM-7R2 Cam brg set w.020 oversize OD GM-7-1R std GM-7-2R2 2,3, GM HO-2S Cam brg set w #5 position HO und HO HO HO HO-2-5S IN-17R2 Cam brg set w.020 oversize OD IN-17-1S std IN-17-2S 2,3,4, *Denotes half shell bearings **Denotes balance shaft bearings 15

18 SPECIALTY CAMSHAFT BEARING SETS SET NO. COMMENTS CONTENTS POSITION HOUSING BORE LENGTH MAX. WALL JDG-7R** Balance shaft set w.078 oversized OD JDG-7-1R 1,2,3,4,5, std MIA-2* OHC cam brg set w heavy wall, MIA-1-7(U) oversize OD MIA-1-5(U) 2,3,4, (heavy wall) MIA-1-6(L) 1,2,3,4, N-7B Special oil control set N std w OD groove in #2 & #3 position N-7-2B N-7-3B N PD-28B Special oil control set PD std w OD groove in #2 & #3 position PD-28-2B PD-28-3B PD SBF-1R1T HP Cam brg set w.010 oversize OD 351-HPB-1R std 351-HPB-2R HPB-3R HPB-4R HPB-5R *Denotes half shell bearings **Denotes balance shaft bearings 16

19 SPECIALTY BEARING COMPONENT LISTING BY HOUSING BORE MINIMUM CAM JOURNAL COMPONENT HOUSING BORE LENGTH MAX. WALL DIAMETER COMMENTS MIG-2-1R L OD Groove, 3 Oil Holes 19502LT OD Groove, 3 Oil Holes BRO Oil Hole, 1 Pin Hole 19500L L OD Groove, 3 Oil Holes 19501LT OD Groove, 3 Oil Holes CH-12-3L OD Groove, 3 Oil Holes CH-12-3LT OD Groove, 3 Oil Holes CHP-12-3LT OD Groove, 3 Oil Holes GMP GMP-1-1T GMP GMP-2-1T LR LR OD Groove, 3 Oil Holes CH-12-3LR OD Groove, 3 Oil Holes 19500LR LR OD Groove, 3 Oil Holes CH-12-3LR OD Groove, 3 Oil Holes 19500LR LR OD Groove, 3 Oil Holes CH-12-3LR OD Groove, 3 Oil Holes 19500LR GM GM2125-1T GM GM GM GM2125-4T GM GM GM GM GM GM GM GM L GM GM GM No Oil Hole GM No Oil Hole 60215P OD Groove, 3 Oil Holes GM OD Groove, 3 Oil Holes GM-55-1T OD Groove, 3 Oil Holes GMP OD Groove, 3 Oil Holes GMP-55-1T OD Groove, 3 Oil Holes BRG OD Groove, 3 Oil Holes GM OD Groove, 3 Oil Holes GM2300-1T OD Groove, 3 Oil Holes GM2300-1R OD Groove, 3 Oil Holes GM2300-1R OD Groove, 3 Oil Holes GM OD Groove, 3 Oil Holes PN OD Groove, No Oil Hole GM OD Groove, 3 Oil Holes GM-60-1A OD Groove, 3 Oil Holes GM-60-1W OD Groove, 3 Oil Holes CN mm 17

20 ID Hi Performance Ad.indd 1 3/22/05 1:09:52 PM 18

21 HIGH PERFORMANCE DISPLACEMENT CYL. CU. IN. L BORE YEAR MAKE/ MODEL(S) ENGINE HI-PERF. COATED CHRYSLER 8 cyl 273ci 4.5L Chrysler OHV (Includes 273A Series) PDP-16 PDP-16T 8 cyl 277ci 4.5L Chrysler OHV PDP-16 PDP-16T 8 cyl 301ci 4.9L Chrysler OHV (Includes Hemi Eng.) PDP-16 PDP-16T 8 cyl 303ci 5.0L Chrysler OHV (Includes Canadian Eng.) PDP-16 PDP-16T 8 cyl 313ci 5.1L Chrysler OHV (Includes Canadian Eng.) PDP-16 PDP-16T 8 cyl 318ci 5.2L Chrysler OHV PDP-16 PDP-16T 8 cyl 318ci 5.2L Chrysler OHV PDP-25 PDP-25T 8 cyl 326ci 5.3L Chrysler OHV (Includes Canadian Eng.) PDP-16 PDP-16T 8 cyl 340ci 5.6L Chrysler OHV PDP-16 PDP-16T 8 cyl 350ci 5.7L Chrysler OHV PDP-17 PDP-17T 8 cyl 360ci 5.9L Chrysler OHV PDP-16 PDP-16T 8 cyl 360ci 5.9L Chrysler OHV PDP-25 PDP-25T 8 cyl 361ci 5.9L Chrysler OHV PDP-17 PDP-17T 8 cyl 383ci 6.3L Chrysler OHV (Includes Canadian Eng.) PDP-17 PDP-17T 8 cyl 400ci 6.6L Chrysler OHV PDP-17 PDP-17T 8 cyl 413ci 6.7L Chrysler OHV PDP-17 PDP-17T 8 cyl 426ci 7.0L Chrysler OHV (Includes Canadian, Hemi Eng.) PDP-17 PDP-17T 8 cyl 440ci 7.2L Chrysler OHV PDP-17 PDP-17T FORD 8 cyl 221ci 3.6L Ford OHV Series L Eng. FP-18 FP-18T 8 cyl 255ci 4.2L Ford OHV Series D Eng. FP-18 FP-18T 8 cyl 260ci 4.3L Ford OHV Series F Eng. FP-18 FP-18T 8 cyl 289ci 4.7L Ford OHV FP-18 FP-18T 8 cyl 302ci 5.0L Ford OHV Series D, E, F, G, J, M, P, Y Eng. FP-18 FP-18T 8 cyl 302ci 5.0L NA Ford SVO S302 Block (2.204 hsg. bore) 351HP 351HPT 8 cyl 302ci 5.0L NA Ford SVO S302 Block O.D. (2.214 hsg. bore) 351HP-R1 8 cyl 302ci 5.0L NA Ford SVO R302 Block (2.204 hsg. bore) 351RHP 351RHPT 19

22 HIGH PERFORMANCE DISPLACEMENT CYL. CU. IN. L BORE YEAR MAKE/ MODEL(S) ENGINE HI-PERF. COATED FORD (CONT'D) 8 cyl 330ci 5.4L Ford OHV Series MD, HD Eng. FP-33 FP-33T 8 cyl 332ci 5.4L Ford OHV Series B, G Eng. FP-33 FP-33T 8 cyl 351ci 5.8L Ford 351W - Windsor Series C, G, H, M, W Eng. FP-18 FP-18T 8 cyl 351ci 5.8L Ford 351C-Cleveland, CJ Series H Eng., FP-26 FP-26T 351M - Modified Series G, H Eng. 8 cyl 351ci 5.8L NA Ford SVO S351, V351, W351, R352 Block (2.204 hsg. bore) 351HP 351HPT 8 cyl 351ci 5.8L NA Ford SVO S351, V351, W351, R352 Block O.D. 351HP-R1 (2.214 hsg. bore) 8 cyl 351ci 5.8L NA Ford SVO R351 Block (2.204 hsg. bore) 351RHP 351RHPT 8 cyl 352ci 5.8L Ford OHV Series D, H, R Eng. FP-33 FP-33T 8 cyl 359ci 5.9L Ford OHV Series MD, HD Eng. FP-33 FP-33T 8 cyl 360ci 5.9L Ford OHV Series LD, MD Eng. FP-33 FP-33T 8 cyl 361ci 5.9L Ford OHV Series MD, HD Eng. FP-33 FP-33T 8 cyl 370ci 6.1L Ford OHV Series MD, HD Eng. FP-30 FP-30T 8 cyl 370ci 6.1L Ford OHV Series MD, HD Eng O.D. FP-30R 8 cyl 389ci 6.4L Ford OHV Series MD, HD Eng. FP-33 FP-33T 8 cyl 390ci 6.4L Ford OHV Series G-Z Eng. FP-33 FP-33T 8 cyl 391ci 6.4L Ford OHV Series MD, HD Eng. FP-33 FP-33T 8 cyl 400ci 6.6L Ford OHV Series S, Z Eng. FP-26 FP-26T 8 cyl 406ci 6.6L Ford OHV Series B, G Eng. FP-33 FP-33T 8 cyl 410ci 6.7L Ford OHV Series M Eng. FP-33 FP-33T 8 cyl 427ci 7.0L Ford OHV FP-33 FP-33T 8 cyl 428ci 7.0L Ford OHV Series P, Q, R Eng. FP-33 FP-33T 8 cyl 429ci 7.0L Ford OHV Series J-R Eng. FP-30 FP-30T 8 cyl 429ci 7.0L Ford OHV Series J-R Eng O.D. FP-30R 8 cyl 460ci 7.5L Ford OHV Series A, C, G, J, L Eng. FP-30 FP-33T 8 cyl 460ci 7.5L Ford OHV Series A, C, G, J, L Eng O.D. FP-30R GENERAL MOTORS 6 cyl 181ci 3.0L Buick OHV Type L Eng. (w/ 20 bolt oil pan) BP-13 BP-13T 20

23 HIGH PERFORMANCE DISPLACEMENT CYL. CU. IN. L BORE YEAR MAKE/ MODEL(S) ENGINE HI-PERF. COATED GENERAL MOTORS (CONT'D) 4 cyl 195ci 3.2L Pontiac OHV PP-3 PP-3T 4 cyl 195ci 3.2L Pontiac OHV PP-4 PP-4T 6 cyl 200ci 3.3L Chevrolet OHV Type M Eng. CHP-17 CHP-17T 6 cyl 204ci 3.3L Buick OHV Type N Eng. BP-13 BP-13T 6 cyl 229ci 3.8L Chevrolet OHV Type K, 9 Eng. CHP-17 CHP-17T 6 cyl 231ci 3.8L Buick OHV Type C, E, K, L Eng. (w/ 20 bolt oil pan) BP-13 BP-13T 6 cyl 262ci 4.3L Chevrolet OHV Type B, N, W, X, Z Eng. CHP-17 CHP-17T (Includes H.O., Turbo (91-93)) 8 cyl 262ci 4.3L Chevrolet OHV Type G Eng. CHP-8 CHP-8T 8 cyl 262ci 4.3L Chevrolet OHV Type G Eng O.D. (2.030 hsg. bore) CHP-8R1 CHP-8R1T 8 cyl 262ci 4.3L Chevrolet OHV Type G Eng O.D. (2.040 hsg. bore) CHP-8R2 CHP-8R2T 8 cyl 262ci 4.3L Chevrolet OHV Type G Eng O.D. (2.050 hsg. bore) CHP-8R3 CHP-8R3T 8 cyl 262ci 4.3L Chevrolet OHV Type G Eng O.D. (2.060 hsg. bore) CHP-8R4 CHP-8R4T 8 cyl 265ci 4.3L Chevrolet OHV (Includes Canadian Eng.) CHP-4 CHP-4T 8 cyl 265ci 4.3L Chevrolet OHV Type W Eng. CHP-8 CHP-8T 8 cyl 265ci 4.3L Chevrolet OHV Type W Eng O.D. (2.030 hsg. bore) CHP-8R1 CHP-8R1T 8 cyl 265ci 4.3L Chevrolet OHV Type W Eng O.D. (2.040 hsg. bore) CHP-8R2 CHP-8R2T 8 cyl 265ci 4.3L Chevrolet OHV Type W Eng O.D. (2.050 hsg. bore) CHP-8R3 CHP-8R3T 8 cyl 265ci 4.3L Chevrolet OHV Type W Eng O.D. (2.060 hsg. bore) CHP-8R4 CHP-8R4T 8 cyl 265ci 4.3L Pontiac OHV Type S Eng. PP-4 PP-4T 8 cyl 267ci 4.4L Chevrolet OHV Type J Eng. CHP-8 CHP-8T 8 cyl 267ci 4.4L Chevrolet OHV Type J Eng O.D. (2.030 hsg. bore) CHP-8R1 CHP-8R1T 8 cyl 267ci 4.4L Chevrolet OHV Type J Eng O.D. (2.040 hsg. bore) CHP-8R2 CHP-8R2T 8 cyl 267ci 4.4L Chevrolet OHV Type J Eng O.D. (2.050 hsg. bore) CHP-8R3 CHP-8R3T 8 cyl 267ci 4.4L Chevrolet OHV Type J Eng O.D. (2.060 hsg. bore) CHP-8R4 CHP-8R4T 8 cyl 283ci 4.6L Chevrolet OHV (Includes Canadian Eng.) CHP-4 CHP-4T 8 cyl 283ci 4.6L Chevrolet OHV (Includes Canadian Eng.) CHP-8 CHP-8T 8 cyl 283ci 4.6L Chevrolet OHV O.D. (2.030 hsg. bore) CHP-8R1 CHP-8R1T 21

24 HIGH PERFORMANCE DISPLACEMENT CYL. CU. IN. L BORE YEAR MAKE/ MODEL(S) ENGINE HI-PERF. COATED GENERAL MOTORS (CONT'D) 8 cyl 283ci 4.6L Chevrolet OHV O.D. (2.040 hsg. bore) CHP-8R2 CHP-8R2T 8 cyl 283ci 4.6L Chevrolet OHV O.D. (2.050 hsg. bore) CHP-8R3 CHP-8R3T 8 cyl 283ci 4.6L Chevrolet OHV O.D. (2.060 hsg. bore) CHP-8R4 CHP-8R4T 8 cyl 287ci 4.7L Pontiac OHV PP-3 PP-3T 8 cyl 288ci 4.7L Pontiac OHV PP-3 PP-3T 8 cyl 294ci 4.8L Chevrolet OHV Vortec 4800 Type V Eng. CHP-10 CHP-10T 8 cyl 301ci 4.9L Pontiac OHV Type W Eng. (Includes Turbo) PP-4 PP-4T 8 cyl 302ci 5.0L Chevrolet OHV (Includes Canadian Eng.) CHP-8 CHP-8T 8 cyl 302ci 5.0L Chevrolet OHV (Includes Canadian Eng.) CHP-8R1 CHP-8R1T O.D. (2.030 hsg. bore) 8 cyl 302ci 5.0L Chevrolet OHV (Includes Canadian Eng.) CHP-8R2 CHP-8R2T O.D. (2.040 hsg. bore) 8 cyl 302ci 5.0L Chevrolet OHV (Includes Canadian Eng.) CHP-8R3 CHP-8R3T O.D. (2.050 hsg. bore) 8 cyl 302ci 5.0L Chevrolet OHV (Includes Canadian Eng.) CHP-8R4 CHP-8R4T O.D. (2.060 hsg. bore) 8 cyl 305ci 5.0L Chevrolet OHV Type E-H, Q, M, S, U, X Eng. CHP-8 CHP-8T 8 cyl 305ci 5.0L Chevrolet OHV Type E-H, Q, M, S, U, X Eng. CHP-8R1 CHP-8R1T O.D. (2.030 hsg. bore) 8 cyl 305ci 5.0L Chevrolet OHV Type E-H, Q, M, S, U, X Eng. CHP-8R2 CHP-8R2T O.D. (2.040 hsg. bore) 8 cyl 305ci 5.0L Chevrolet OHV Type E-H, Q, M, S, U, X Eng. CHP-8R3 CHP-8R3T O.D. (2.050 hsg. bore) 8 cyl 305ci 5.0L Chevrolet OHV Type E-H, Q, M, S, U, X Eng. CHP-8R4 CHP-8R4T O.D. (2.060 hsg. bore) 8 cyl 307ci 5.0L Chevrolet OHV Type A, F Eng. CHP-8 CHP-8T 8 cyl 307ci 5.0L Chevrolet OHV Type A, F Eng O.D. (2.030 hsg. bore) CHP-8R1 CHP-8R1T 8 cyl 307ci 5.0L Chevrolet OHV Type A, F Eng O.D. (2.040 hsg. bore) CHP-8R2 CHP-8R2T 8 cyl 307ci 5.0L Chevrolet OHV Type A, F Eng O.D. (2.050 hsg. bore) CHP-8R3 CHP-8R3T 8 cyl 307ci 5.0L Chevrolet OHV Type A, F Eng O.D. (2.060 hsg. bore) CHP-8R4 CHP-8R4T 8 cyl 316ci 5.2L Pontiac OHV PP-3 PP-3T 8 cyl 325ci 5.3L Chevrolet OHV Vortec 5300 Type T Eng. CHP-10 CHP-10T 8 cyl 326ci 5.3L Pontiac OHV PP-4 PP-4T 8 cyl 327ci 5.3L Chevrolet OHV CHP-4 CHP-4T 8 cyl 327ci 5.3L Chevrolet OHV CHP-8 CHP-8T 22

25 HIGH PERFORMANCE DISPLACEMENT CYL. CU. IN. L BORE YEAR MAKE/ MODEL(S) ENGINE HI-PERF. COATED GENERAL MOTORS (CONT'D) 8 cyl 327ci 5.3L Chevrolet OHV O.D. (2.030 hsg. bore) CHP-8R1 CHP-8R1T 8 cyl 327ci 5.3L Chevrolet OHV O.D. (2.040 hsg. bore) CHP-8R2 CHP-8R2T 8 cyl 327ci 5.3L Chevrolet OHV O.D. (2.050 hsg. bore) CHP-8R3 CHP-8R3T 8 cyl 327ci 5.3L Chevrolet OHV O.D. (2.060 hsg. bore) CHP-8R4 CHP-8R4T 8 cyl 336ci 5.5L GMC OHV PP-3 PP-3T 8 cyl 346ci 5.7L Chevrolet OHV LS-1, LS-6 Mark III Type G, R Eng. (1st Series) CHP-10 CHP-10T 8 cyl 346ci 5.7L Chevrolet OHV LS-1, LS-6 Mark III Type G, R Eng. (2nd Series) CHP-23 CHP-23T 8 cyl 347ci 5.7L Pontiac OHV Type A, B Eng. PP-3 PP-3T 8 cyl 350ci 5.7L Pontiac OHV Type A, B, E, K, M, N, P Eng. PP-4 PP-4T 8 cyl 350ci 5.7L Buick OHV Type B, H, J, X Eng. BP-9 BP-9T 8 cyl 350ci 5.7L Chevrolet OHV Type G, H, K, L, M, P, R, T, V, X, Y, 4, 6, 7, 8 Eng. CHP-8 CHP-8T 8 cyl 350ci 5.7L Chevrolet OHV Type G, H, K, L, M, P, R, T, V, X, Y, 4, 6, 7, 8 Eng. CHP-8R1 CHP-8R1T O.D. (2.030 hsg. bore) 8 cyl 350ci 5.7L Chevrolet OHV Type G, H, K, L, M, P, R, T, V, X, Y, 4, 6, 7, 8 Eng. CHP-8R2 CHP-8R2T O.D. (2.040 hsg. bore) 8 cyl 350ci 5.7L Chevrolet OHV Type G, H, K, L, M, P, R, T, V, X, Y, 4, 6, 7, 8 Eng. CHP-8R3 CHP-8R3T O.D. (2.050 hsg. bore) 8 cyl 350ci 5.7L Chevrolet OHV Type G, H, K, L, M, P, R, T, V, X, Y, 4, 6, 7, 8 Eng. CHP-8R4 CHP-8R4T O.D. (2.060 hsg. bore) 8 cyl 350ci 5.7L ON Chevrolet Bowtie Block (2.000 hsg. bore) GMP-8 GMP-8T 8 cyl 350ci 5.7L NA Oldsmobile Rocket Eng. (2.120 hsg. bore) GMP-1 GMP-1T 8 cyl 350ci 5.7L NA Hi-Perf. Block with 55mm (2.282 hsg. bore) GMP-55 GMP-55T 8 cyl 365ci 6.0L Chevrolet OHV Vortec 6000 Type U Eng. CHP-10 CHP-10T 8 cyl 366ci 6.0L Chevrolet OHV Type E, L Eng. CHP-12 CHP-12T 8 cyl 366ci 6.0L Chevrolet OHV Type E, L Eng O.D. (2.150 hsg. bore) CHP-12R1 8 cyl 366ci 6.0L Chevrolet OHV Type E, L Eng O.D. (2.160 hsg. bore) CHP-12R2 8 cyl 370ci 6.1L Pontiac OHV PP-3 PP-3T 8 cyl 389ci 6.4L Pontiac OHV PP-3 PP-3T 8 cyl 389ci 6.4L Pontiac OHV PP-4 PP-4T 8 cyl 396ci 6.5L Chevrolet OHV Big Block CHP-12 CHP-12T 8 cyl 396ci 6.5L Chevrolet OHV Big Block O.D. (2.150 hsg. bore) CHP-12R1 23

26 HIGH PERFORMANCE DISPLACEMENT CYL. CU. IN. L BORE YEAR MAKE/ MODEL(S) ENGINE HI-PERF. COATED GENERAL MOTORS (CONT'D) 8 cyl 396ci 6.5L Chevrolet OHV Big Block O.D. (2.160 hsg. bore) CHP-12R2 8 cyl 400ci 6.6L Buick OHV BP-9 BP-9T 8 cyl 400ci 6.6L Pontiac OHV Type R Eng. PP-4 PP-4T 8 cyl 400ci 6.6L Chevrolet OHV Small Block CHP-8 CHP-8T 8 cyl 400ci 6.6L Chevrolet OHV Small Block O.D. (2.030 hsg. bore) CHP-8R1 CHP-8R1T 8 cyl 400ci 6.6L Chevrolet OHV Small Block O.D. (2.040 hsg. bore) CHP-8R2 CHP-8R2T 8 cyl 400ci 6.6L Chevrolet OHV Small Block O.D. (2.050 hsg. bore) CHP-8R3 CHP-8R3T 8 cyl 400ci 6.6L Chevrolet OHV Small Block O.D. (2.060 hsg. bore) CHP-8R4 CHP-8R4T 8 cyl 400ci 6.6L Chevrolet OHV Big Block CHP-12 CHP-12T 8 cyl 400ci 6.6L Chevrolet OHV Big Block O.D. (2.150 hsg. bore) CHP-12R1 8 cyl 400ci 6.6L Chevrolet OHV Big Block O.D. (2.160 hsg. bore) CHP-12R2 8 cyl 400ci 6.6L NA Oldsmobile Rocket Eng. (2.120 hsg. bore) GMP-1 GMP-1T 8 cyl 402ci 6.6L Chevrolet OHV Big Block CHP-12 CHP-12T 8 cyl 402ci 6.6L Chevrolet OHV Big Block O.D. (2.150 hsg. bore) CHP-12R1 8 cyl 402ci 6.6L Chevrolet OHV Big Block O.D. (2.160 hsg. bore) CHP-12R2 8 cyl 421ci 6.9L Pontiac OHV PP-4 PP-4T 8 cyl 421ci 6.9L Pontiac OHV PP-3 PP-3T 8 cyl 427ci 7.0L Chevrolet OHV Big Block (Includes Aluminum Block) CHP-12 CHP-12T 8 cyl 427ci 7.0L Chevrolet OHV Big Block (Includes Aluminum Block) CHP-12R O.D. (2.150 hsg. bore) 8 cyl 427ci 7.0L Chevrolet OHV Big Block (Includes Aluminum Block) CHP-12R O.D. (2.160 hsg. bore) 8 cyl 428ci 7.0L Pontiac OHV PP-4 PP-4T 8 cyl 430ci 7.0L Buick OHV BP-9 BP-9T 8 cyl 454ci 7.4L Chevrolet OHV Big Block Type J, L, N, S, V, W, Y Eng. CHP-12 CHP-12T (Includes Aluminum Block) 8 cyl 454ci 7.4L Chevrolet OHV Big Block Type J, L, N, S, V, W, Y Eng. CHP-12R1 (Includes Aluminum Block) O.D. (2.150 hsg. bore) 8 cyl 454ci 7.4L Chevrolet OHV Big Block Type J, L, N, S, V, W, Y Eng. CHP-12R2 (Includes Aluminum Block) O.D. (2.160 hsg. bore) 8 cyl 455ci 7.5L Buick OHV Type T, U, V Eng. BP-9 BP-9T 8 cyl 455ci 7.5L Pontiac OHV Type Y (H.O., S.D.) Eng. PP-4 PP-4T 24

27 HIGH PERFORMANCE DISPLACEMENT CYL. CU. IN. L BORE YEAR MAKE/ MODEL(S) ENGINE HI-PERF. COATED GENERAL MOTORS (CONT'D) 8 cyl 496ci 8.1L Chevrolet OHV Vortec 8100 L18 CHP-12 CHP-12T 8 cyl 496ci 8.1L Chevrolet OHV Vortec 8100 L O.D. (2.150 hsg. bore) CHP-12R1 8 cyl 496ci 8.1L Chevrolet OHV Vortec 8100 L O.D. (2.160 hsg. bore) CHP-12R2 8 cyl 502ci 8.2L NA Chevrolet OHV Bowtie Block CHP-12 CHP-12T 8 cyl 502ci 8.2L NA Chevrolet OHV Bowtie Block O.D. (2.150 hsg. bore) CHP-12R1 8 cyl 502ci 8.2L NA Chevrolet OHV Bowtie Block O.D. (2.160 hsg. bore) CHP-12R2 8 cyl 502ci 8.2L NA Chevrolet Bowtie Block (2.120 hsg. bore) GMP-12 GMP-12T ISUZU 6 cyl 262ci 4.3L Chevrolet OHV LB4, LF6-Hi Output X Series Eng. CHP-17 CHP-17T 8 cyl 350ci 5.7L Chevrolet OHV Type G, H, K, L, M, P, R, T, V, X, Y, 4, 6, 7, 8 Eng. CHP-8 CHP-8T (Includes Vortec, Aluminum Block) 8 cyl 350ci 5.7L Chevrolet OHV Type G, H, K, L, M, P, R, T, V, X, Y, 4, 6, 7, 8 Eng. CHP-8R1 CHP-8R1T (Includes Vortec, Aluminum Block) O.D. (2.030 hsg. bore) 8 cyl 350ci 5.7L Chevrolet OHV Type G, H, K, L, M, P, R, T, V, X, Y, 4, 6, 7, 8 Eng. CHP-8R2 CHP-8R2T (Includes Vortec, Aluminum Block) O.D. (2.040 hsg. bore) 8 cyl 350ci 5.7L Chevrolet OHV Type G, H, K, L, M, P, R, T, V, X, Y, 4, 6, 7, 8 Eng. CHP-8R3 CHP-8R3T (Includes Vortec, Aluminum Block) O.D. (2.050 hsg. bore) 8 cyl 350ci 5.7L Chevrolet OHV Type G, H, K, L, M, P, R, T, V, X, Y, 4, 6, 7, 8 Eng. CHP-8R4 CHP-8R4T (Includes Vortec, Aluminum Block) O.D. (2.060 hsg. bore) JEEP 8 cyl 318ci 5.2L Chrysler OHV Type Y Eng. PDP-25 PDP-25T 8 cyl 350ci 5.7L Buick OHV Type Y Eng. BP-9 BP-9T 8 cyl 360ci 5.9L Chrysler OHV Type Z Eng. PDP-25 PDP-25T STUDEBAKER 8 cyl 283ci 4.6L Chevrolet OHV CHP-8 CHP-8T VOLVO-PENTA 8 cyl 305ci 5.0L Volvo-Penta (Chevrolet) AQ200D, AQ225D, BB225A, BB225AV CHP-8 CHP-8T Marine Eng. 8 cyl 350ci 5.7L Volvo-Penta (Chevrolet) AQ260A, AQ290A, BB260A, BB260AV CHP-8 CHP-8T Marine Eng. SPECIALTY AFTERMARKET BLOCKS 8 cyl NA NA NA NA Dart, Little "M" Block, (2.000 hsg bore), O.D. groove DT-1T with 3 hole, 120 degree spacing. (+.010 O.D.) DT-1TR1 8 cyl NA NA NA NA Dart, Big "M" Block, (2.120 hsg bore), O.D. groove GMP-12LT with 3 hole, 120 degree spacing. 8 cyl NA NA NA NA Dart, Iron Eagle GMP-2T 8 cyl NA NA NA NA Dart, Ford SVO Block SBF-1T (+.010 O.D.) SBF-1R1T 25

28 26

29 27

30 28

31 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * Special ID features 29

32 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * Special ID features 30

33 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * Special ID features 31

34 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * Special ID features 32

35 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * Special ID features 33

36 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * * Special ID features 34

37 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * Special ID features 35

38 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * Special ID features 36

39 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * Special ID features 37

40 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * Special ID features 38

41 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * Special ID features 39

42 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * Special ID features 40

43 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * * * * * * Special ID features 41

44 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * Special ID features 42

45 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * * * Special ID features 43

46 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * * Special ID features 44

47 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * Special ID features 45

48 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * Special ID features 46

49 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * Special ID features 47

50 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * Special ID features 48

51 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * * * Special ID features 49

52 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * * * Special ID features 50

53 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * * * * * Special ID features 51

54 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * * * * * Special ID features 52

55 VALVE SEAT PROGRESSIVE LISTING BY OUTSIDE DIAMETER PART NUMBER SERIES ACTUAL ID TOP SEAT OD ID TAPER DEPTH ANGLE * * Specialty Seats / * / * * Special ID features 53

56 WE SUPPORT CHARTER MEMBER 54

57 55

58 ENGINE HARDWARE MAKE & PRODUCT DIMENSION PART NO. APPLICATION TYPE O.D. I.D. LENGTH CHRYSLER CAM BOLTS & WASHERS AB-040-P V-8 Cam Bolt FORD 7/16-14 x 1 Hex HEAD DOWELS AD L Hollow Dowel SPACER SP L Spacer TIMING COVER DOWELS AD L Hollow Dowel GENERAL MOTORS CAM BOLTS & WASHERS AB-6501-P (6.2L) / (6.5L) Chevy Diesel Cam Bolt AW-6502-P (6.2L) / (6.5L) Chevy Diesel Cam Bolt Washer 12mm-1.75 x 40mm Hex 31/64 x 1-7/8 x 1/4 Washer CAM BOX DOWELS AD L Ecotech Hollow Dowel CAM LOCK PLATE AW-013-P All Other GM V6 / V8 Hi Perf. Cam Lock Plate N/A N/A N/A CAM RETAINER AW-6504-P (6.2L) / (6.5L) Chevy Diesel Cam Retainer N/A N/A N/A CAM SHIM AW-6503-P (6.2L) / (6.5L) Chevy Diesel Cam Shim N/A N/A N/A CAM SPACER SP L(230ci) Cam Spacer OIL DIPSTICK PLUGS AP L (262ci) Oil Dipstick Plug N/A N/A N/A OIL FILTER ADAPTER BOLTS AB-039-P All Other GM V6 / V8 Hi Perf. Bolt 5/16-18 x TIMING GEAR OILER TC-4 2.5L (151ci), 3.8L (230ci), 4.1L (250ci), 4.8L (292ci) Timing Gear Oiler (Press in Type) N/A N/A N/A TRANSMISSION DOWELS AD-023 All Other GM V6 / V8 Hi Perf. Solid Dowel Solid

59 57

60 ENGINE HARDWARE FINISHING KITS MAKE & DIMENSION KIT NO. YEAR APPLICATION CONTENTS QTY. DESCRIPTION O.D. I.D. LENGTH CHRYSLER FKP-2 Dodge/Chrysler/Plymouth AD-1284-P 4 Head Dowel Solid SB V CID AD-1284-P 2 Timing Cover Solid AB-040-P 1 Cam Bolt 7/16-14 x 1 Hex AW-006-P 1 Cam Bolt Washer (Tapered) 1-1/2 x 7/16 x 1/8 Washer AD Distributor Tower Shaft Bushing N/A N/A N/A AK-005-P 1 Woodruff Key Optional parts not included in kit. 3/16 x 1-13/16 AD Transmission Dowel Solid GENERAL MOTORS FKC-1HP Chevy SB V CID AD-927-P 4 Head Dowel Solid (Hi Performance) AD-1284-P 4 Timing Cover / Oil Pump Dowel Solid AB-001-P 3 Cam Bolt 5/16-18 x 3/4 Hex AW-013-P 1 Cam Lock Plate N/A N/A N/A AB-039-P 2 Oil Filter Adapter Bolts 5/16-18 x AK-001-P 1 Woodruff Key 3/16 x 1-3/8 AK-002-P 2 Woodruff Key 3/16 x 3/4 AD Transmission Dowel Solid FKC-3HP Chevy BB V CID AD-8081-P 4 Head Dowel (Hi Performance) AD-1284-P 4 Timing Cover / Oil Pump Dowel Solid AW-013-P 1 Cam Lock Plate N/A N/A N/A AB-039-P 2 Oil Filter Adapter Bolts 5/16-18 x AB-001-P 3 Cam Bolt 5/16-18 x 3/4 Hex AK-002-P 2 Woodruff Key 3/16 x 3/4 AD Transmission Dowel Solid FKC-5A Chevy Diesel (6.2L) / (6.5L) AB-6501-P 1 Cam Bolt 12mm-1.75 x 40mm Hex AW-6502-P 1 Cam Bolt Washer 31/64 x 1-7/8 x 1/4 Washer AW-6504-P 1 Cam Retainer N/A N/A N/A AW-6503-P 1 Cam Shim N/A N/A N/A 58

61 59