Submersible Pumps. 5'' CS Series Pumps

Transcription

1 5'' CS Series Pumps 1

2 Submersible Pumps 5 5 CS CS Series Pumps Features Ordering Information Model Number Explanation 3 CS 4-1 Ordering Information Phase No. of Stages Series m 3 BEP Model FE Order No. kw Phase Stages 3CS All 0.55 stainless construction: 1 All CS 4 components in contact with the pumped fluid, including hydraulics, are made from 304 stainless steel to provide superior 3CS efficiency and performance over a wide variety of applications. 3CS CS Compact 0.9 close-coupled 1 design: 7 Suitable for most common water well applications, the CS may also be operated in fountains, cisterns, or 3CS watercourses, 1.1 either 1 vertically or 8horizontally. Accessories FE Order No Power cable, M Float switch Applications: Domestic water supply Pressure boosting Irrigation Features: Fountains Septic effluent pumping Water distribution Model FE Order No. Easy installation: The single phase version is equipped with internal capacitor and kwthermal motor Phase protection, Stages eliminating the need for a separate control panel. 5CS Easy plug-in type wiring connections: Both the power cord and the fl oat 5CS switch 0.9 can be easily 1 replaced in case 5 of damage. 5CS Sealed motor: The long-life motor is completely sealed in a water-tight stainless enclosure and is cooled by the pumped fluid. Double mechanical seal: The internal motor electrical components are further protected by two mechanical seals lubricated by an oil chamber (FDA compliant) that prevents wear and damage from running dry. Heavy duty motor shaft: An oversized motor shaft extends through pump and is Description designed to maintain alignment while handling mechanical stresses as it provides smooth transfer of power to the stages. Specifications: Switch socket plug Capacities up to 7.5 m 3 /h Start switch connector Heads up to 8 Bar (80 metres) Maximum working pressure: 10 Bar Discharge size: 1.25 inches BSPP Maximum immersion: m Maximum solids size up to 2 mm Class F insulation, IP68 protection Duty rating: Continuous either vertical or horizontal up to maximum ambient temperature of o C Maximum starts per hour: Level control included m power cable type H07RN F supplied with AU/NZ 2-3 pin plug 1

3 Ordering Information Model Number Explanation 3 CS 4-1 Phase No. of Stages Series m 3 BEP Ordering Information Model FE Order No. kw Phase Stages 3CS CS CS CS CS Model FE Order No. kw Phase Stages 5CS CS CS Accessories FE Order No. Description Power cable, M Float switch Switch socket plug Start switch connector 2

4 Performance and Dimensional Data Performance Chart Model Stages Motor Power Input Power Internal Capacitor Rated Current Single-Phase kw HP kw µf V 2-2 V, 50 Hz Length (mm) 3CS CS CS CS CS Weight (kg) Model Stages Motor Power Input Power Internal Capacitor Rated Current Single-Phase kw HP kw µf V 2-2 V, 50 Hz Length (mm) 5CS CS CS Weight (kg) Dimensions Rp 1 ¼ 230 mm 7 mm 175 mm PACKAGING Lt Ø134 3

5 Performance Curves ft 3 m 100 3CS Performance Curves rpm CS CS CS6 Total head CS5 3CS l/min (m 3 /h) U.S. gpm Efficiency % 50 ηp l/min (m 3 /h) U.S. gpm Capacity 4

6 Performance Curves ft m 90 5CS Performance Curves rpm CS CS5 Total head CS l/min (m 3 /h) U.S. gpm Efficiency % ηp l/min Capacity (m 3 /h) U.S. gpm 5 5

7 Components & Materials of Construction Ref. No. Description Screws and flanges for pre-loading assembly Power cable assembly Seeger-ring Level control assembly Capacitor with cables and connectors Clamp for capacitor.00 Outer case with discharge head.01 Suction strainer Motor housing and stator Upper motor cover Upper bearing housing with cover Lower motor cover Lower bearing cover Kit O-Rings (5 pcs) Kit mechanical seals (2 pcs) Kit ball bearings (2 pcs) Rotor and pump shaft Kit screws, nut and washers.00 Stage housing and diffuser.01 Spacer.02 Floating neck ring assembly.03 Initial stage housing Impeller Impeller spacers (2 pcs).01 Materials of Construction No. Part Description Material / Flanges for preloading assembly Stainless steel DIN-EN (AISI 304).00 Outer case with discharge head Stainless steel DIN-EN / (AISI 441/304).01 Suction strainer Stainless steel DIN-EN (AISI 304) Motor housing Stainless steel DIN-EN (AISI 304) / Covers/flanges motor casing Stainless steel DIN-EN (AISI 304) Pump shaft Stainless steel DIN-EN (AISI 304).00 /.01 /.03 Diffuser/s Stainless steel DIN-EN (AISI 304) / Impeller/s with spacers Stainless steel DIN-EN (AISI 304) Screws and washers Stainless steel DIN-EN (AISI 304) O-Ring NBR / Upper mechanical seal Ceramic/Carbon/NBR Lower mechanical seal Ceramic/Carbon/NBR 6

8 AUSTRALIA / NEW ZEALAND Franklin Electric (Australia) Pty. Ltd Micro Circuit Dandenong South, Victoria 3175 Australia Phone: Fax: Toll Free: 1300-FRANKLIN FE