INSTALLATION INSTRUCTION

Transcription

1 EN 795: 2012 Class CE TYPE TEST CE PRODUCTION QULITY CONTROL No SI Kitemark Court Davy venue Knowlhill Milton Keynes MK5 8PP United Kingdom No SI Product Services Kitemark Court Davy venue Knowlhill, Milton Keynes MK5 8PP, UK Floor Mounted Jib ase Model Numbers: , INSTLLTION INSTRUCTION , FORM NO: REV: E 3M 2006

2 2 175mm (6-7/8 in) 175mm (6-7/8 in) 175mm (6-7/8 in) 349mm (13-3/4 in) 175mm (6-7/8 in) 349mm (13-3/4 in)

3

4 EN WRNING: This product is part of a Personal Fall rrest and Work Positioning system. The user must follow the manufacturer s instructions for each component of the system. These instructions must be provided to the user of this equipment. The user must read and understand these instructions before using this equipment. Manufacturer s instructions must be followed for proper use and maintenance of this equipment. lterations or misuse of this product or failure to follow instructions may result in serious injury or death. If this product is resold outside the original country of destination, the reseller must provide these instructions in the language of the country in which the product will be used. IMPORTNT: If you have questions on the use, care, or suitability of this equipment for your application, contact Capital Safety. IMPORTNT: efore using this equipment, record the product identification information from the ID label into the inspection and maintenance log of this manual. IMPORTNT: Systems are designed to be used with Jib Systems manufactured by Capital Safety only. OSH Models ll connecting systems, (self retracting lifelines, winches and energy absorbing lanyards) used with the Jib Mast and ase system shall limit the average arresting forces to 4 kn (900 lbf). IMPORTNT: System is only rated for one user. CE Models ll connecting systems, (self retracting lifelines, winches and energy absorbing lanyards) used with the Jib Mast and ase system shall limit the average arresting forces to 6 kn (1350 lbf). IMPORTNT: System is only rated for one user SPECIFICTIONS: General Construction Structural Material Finish Welded Steel 36 Steel Sherwin Williams, N.L. Yellow, PYS8-C8589 Powder Coat Training: It is the responsibility of users of this equipment to understand these instructions and be trained in correct installation, use, and maintenance of this equipment. Users must be aware of the consequences of improper installation or use of this equipment. This instruction manual is not a substitute for a training program. Training must be provided on a periodic basis to ensure user proficiency. Description: The Floor Mounted Jib ase (Figure 1) is a anchor point for overhead applications. The Floor Mounted Jib ase is designed for use with a vertical mast being inserted into a concrete mounted base. Purpose: The Floor Mounted Jib ase is designed for use as a component of a Personal Fall rrest System. PFSs are used where free fall is possible before the fall is arrested and typically include: a Self Retracting Lifeline (EN 360) or Energy bsorbing Lanyard (EN 355); connector (EN 362) to attach to the anchor; and a Full ody Harness (EN 361). INSTLLTION: Concrete anchors and mounting hardware are not included. Mounting hardware must meet the requirements provided in the Fastener Requirements Table below. WRNING: Mounting surface must be able to support a minimum 22kN (4,780 lbf) load. Fastener Requirements Fastener Type Thread Type Pullout Grade Concrete nchor 3/4-10 UNC 34.6 kn (Minimum 7,787 lbs) Minimum Grade 8 olt 3/4-10 UNC 34.6 kn (Minimum 7,787 lbs) Minimum Grade 8 IMPORTNT: See fastener manufacturer specifications for mounting requirements. (See Figure 5 -.) Step-1: Mark anchor holes to be drilled per Figure 2 - layout. Drill hole to Concrete nchor depth specifications. (See Figure 2 -.) Remove debris from hole. Step - 2: Fastening the Mounted Jib ase (See Figure 3.) : Make sure the mounting surface is free of any debris before setting the Jib base in place. Make sure the core holes are free of any debris before inserting anchor bolts. Fasten the Jib ase to the existing concrete by inserting the anchor bolts with washers, and tightening the concrete anchor bolts to their recommended torque. Step - 3: Installing the Jib Mast on to the Jib ase. (See Figure 4.) Lower the Jib Mast until the Rotation lock is resting in the Locking Slot () in the Jib ase. Lower the Jib Mast onto the Jib ase sleeve until the full weight of the mast is on the base. Rotate the mast until the Locking Pin () snaps into the Locking Plate (). 4

5 INSPECTION: IMPORTNT: Extreme working conditions (harsh environments, prolonged use) may require increasing the frequency of inspections.. WRNING: If the system has been damaged do to fall arrest, it must be immediately removed from service, inspected, or contact Capital Safety for repair or replacement. efore Every use: Monthly: LELS: ll fasteners must be tight, secure and not damaged. Inspect for corrosion or rust. ll labels must be present and fully legible. Inspect for cracks around the Jib ase. Record results of inspection in the inspection and maintenance log provided. If inspection reveals an unsafe or defective condition, remove Concrete Mounted Jib ase from service and destroy, or contact Capital Safety for repair or replacement. formal inspection should be done by a Competent Person 1 other than the user. Record results of inspection in the inspection and maintenance log provided. C C 1 Competent Person: One who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them. 5

6 6

7 INSPECTION ND MINTENNCE LOG SERIL NUMER: MODEL NUMER: DTE PURCHSED: DTE OF FIRST USE: INSPECTION DTE INSPECTION ITEMS NOTED CORRECTIVE CTION MINTENNCE PERFORMED

8 LIMITED LIFETIME WRRNTY Warranty to End User: D Industries, LLC dba CPITL SFETY US ( CPITL SFETY ) warrants to the original end user ( End User ) that its products are free from defects in materials and workmanship under normal use and service. This warranty extends for the lifetime of the product from the date the product is purchased by the End User, in new and unused condition, from a CPITL SFETY authorized distributor. CPITL SFETY S entire liability to End User and End User s exclusive remedy under this warranty is limited to the repair or replacement in kind of any defective product within its lifetime (as CPITL SFETY in its sole discretion determines and deems appropriate). No oral or written information or advice given by CPITL SFETY, its distributors, directors, officers, agents or employees shall create any different or additional warranties or in any way increase the scope of this warranty. CPITL SFETY will not accept liability for defects that are the result of product abuse, misuse, alteration or modification, or for defects that are due to a failure to install, maintain, or use the product in accordance with the manufacturer s instructions. CPITL SFETY S WRRNTY PPLIES ONLY TO THE END USER. THIS WRRNTY IS THE ONLY WRRNTY PPLICLE TO OUR PRODUCTS ND IS IN LIEU OF LL OTHER WRRNTIES ND LIILITIES, EXPRESSED OR IMPLIED. CPITL SFETY EXPRESSLY EXCLUDES ND DISCLIMS NY IMPLIED WRRNTIES OF MERCHNTILITY OR FITNESS FOR PRTICULR PURPOSE, ND SHLL NOT E LILE FOR INCIDENTL, PUNITIVE OR CONSEQUENTIL DMGES OF NY NTURE, INCLUDING WITHOUT LIMITTION, LOST PROFITS, REVENUES, OR PRODUCTIVITY, OR FOR ODILY INJURY OR DETH OR LOSS OR DMGE TO PROPERTY, UNDER NY THEORY OF LIILITY, INCLUDING WITHOUT LIMITTION, CONTRCT, WRRNTY, STRICT LIILITY, TORT (INCLUDING NEGLIGENCE) OR OTHER LEGL OR EQUITLE THEORY. US 3833 SL Way Red Wing, MN Toll Free: Phone: Fax: solutions@capitalsafety.com razil Rua nne Frank, 2621 oqueirão Curitiba PR razil Phone: brasil@capitalsafety.com Mexico Calle Norte 35, 895-E Col. Industrial Vallejo C.P zcapotzalco Mexico D.F. Phone: (55) mexico@capitalsafety.com Colombia Compañía Latinoamericana de Seguridad S..S. Carrera 106 #15-25 Interior 105 Manzana 15 Zona Franca - ogotá, Colombia Phone: servicioalcliente@capitalsafety.com Canada 260 Export oulevard Mississauga, ON L5S 1Y9 Phone: Toll-Free: Fax: info.ca@capitalsafety.com EME (Europe, Middle East, frica) EME Headquarters: 5a Merse Road North Moons Moat Redditch, Worcestershire 98 9HL UK Phone: + 44 (0) Fax: + 44 (0) csgne@capitalsafety.com France: Le roc Center Z.I. 1re venue - P Carros Le roc Cedex France Phone: Fax: information@capitalsafety.com ustralia & New Zealand 95 Derby Street Silverwater Sydney NSW 2128 ustralia Phone: +(61) Toll-Free : (US) Toll-Free : (NZ) Fax: +(61) sales@capitalsafety.com.au sia Singapore: 69, Ubi Road 1, #05-20 Oxley izhub Singapore Phone: Fax: inquiry@capitalsafety.com Shanghai: Rm 1406, China Venturetech Plaza 819 Nan Jing Xi Rd, Shanghai , P R China Phone: Fax: inquiry@capitalsafety.cn I S O 9001