- Name & Address Of Buyer: AL-LAMAA PALACE TRAD EST. Add: exit-18 new sulai industrial area riyadh-saudi arabia

Transcription

1 Inspection Order No. : IN-TJ BOSS No: TBA Page No. : 1 of 7 Date of issue: Nov.26th, 2014 INSPECTION REPORT (non-negotiable) - Description and Quantity of Rectangle Tube, SS 316 L Angle,SS316 mesh Commodity: - Name & Address Of Buyer: AL-LAMAA PALACE TRAD EST. Add: exit-18 new sulai industrial area riyadh-saudi arabia - Name & Address Of Seller: JINBAOLAI STEEL TRADING CO.,LTD Add: Room #A1115,Beichen Road &Longzhou Road Sqr.Beichen District, tianjin,china HEBEI SHUOLONG METAL PPPRODUCTS COLTD Add:Anping,Hengshui, Hebei,CHINA - Inspection Date & Place: Nov.25~26th, 2014 anping hebei and xiqing Tianjin, China - Contract No.: Nr: CS and Nr:CS Nov.5, Invoice (Packing List )No. SL date: Nov.5,2014 /10TF7806 date Nov 26, Nature Of Inspection: Item Comment Quantity check Acceptable Visual quality Marking and Subject to client s evaluation Packing check Dimension check Subject to client s evaluation witness the gross Acceptable Witness sampling Acceptable - Inspector: Rock huang - Reviewed by Kevin Li This is to report that we, SGS-CSTC (Tianjin) Co., Ltd. at the request of AL-LAMAA PALACE TRAD EST. conducted the following inspection: Disclaimer This document is issued by the Company under its General Conditions of Service accessible at Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any other holder of this document is advised that information contained hereon reflects the Company s findings at the time of its intervention only and within the limits of Client s instructions, if any. The Company s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS-CSTC Standards Technical Services SGS Mansion, No. 41, The 5th Avenue, TEDA, Tianjin, China, (Tianjin) Co., Ltd. t: +86(0) f +86(0) [V: 02 June. 1 st, 2012] Member of the SGS Group (Société Générale de Surveillance)

2 Instrument checklist During the inspection, the following instrument calibration status has been checked for inspection: No. MEASURING INSTRUMENT DESCRIPTION CALIBRATION CERTIFICATE NO. (Including measuring range and equipment No.) STATUS (OPTIONAL) 1 Steel tape(ind-tj-jc20m-38) Effectively - 2 Micrometer(IN-TJ-QF-21) Effectively - 3 Vernier caliper(ind-tj-kc-40) Effectively - 4 electronic balance Effectively 14h scale N/A N/A Before, SGS inspector required the manufacturer to provided the calibration certificate of scale for review, and it was not provided, the manufacturer declared that the electronic scale was not calibrated, so the value of just for reference. Inspection Finding: 1. Quantity check randomly: Method of quantity check Quantity check by 100%. The details as below: Item Description Req. Quantity pcs Act. Quantity pcs 1 Wire mesh Ss 316l angle tube 30 / Result: The result was acceptable except remark. 2. Visual quality Marking and Packing check randomly: Sample size: ANSI/ASQ, Z , s-4 TOTAL 4pcs During the inspection visual quality, marking and packing check was performed randomly by SGS inspector, all the cargos were nude,no marking was found, no obvious defect was found, such as crack, deformation, broken, etc Result: The result was Subject to client`s evaluation except remark. 3. Dimension check randomly: Sample size: ANSI/ASQ, Z , s-4 TOTAL 4pcs SGS inspector performed dimension check on the inspection site. Total 4rolls were selected randomly for dimension check, the details as below table: Inspection Order No.: IN-TJ Page No.: 2 of 8

3 unit: mm ITEM Sample MS W WD L Wire mesh 2 REQ. VALUE 60* ACT. VALUE 59.15~ ~ ~ ~10050 W W WT L SS 316l angle 2 REQ. VALUE ACT. VALUE 151.5~ ~ ~ ~ Result: The actual measured value for clients reference, due to no tolerance was provide to SGS inspector. So the result Subject to client`s evaluation except remark. 4. witness the gross : Sample size: witness the gross by 100% Total 9 rolls of wire meshes were selected randomly for net and under SGS inspector s witness, before, SGS inspector required the manufacturer to provide the calibration certificate of electronic scale and calibration certificate was Acceptable. Details as follow: Item Description Req. Net weight Act. Net weight 1 Wire mesh / 2 Wire mesh 44.7 / 3 Wire mesh / 4 Wire mesh / 5 Wire mesh / 6 Wire mesh 44.9 / 7 Wire mesh 44.9 / 8 Wire mesh 44.7 / 9 Wire mesh 44.6 / total kg Total 10 pcs of angles were selected randomly for net and under SGS inspector s witness, before, SGS inspector required the manufacturer to provide the calibration certificate of electronic scale and the manufacturer declared that the electronic scale was not calibrated, so the value of just for reference. Details as follow: Item Description Req. Net weight Act. Net weight 1 angles Result: The result Subject to client`s evaluation except remark. Inspection Order No.: IN-TJ Page No.: 3 of 8

4 5. Witness sampling: Sample size: according to requirements of client, 2pcs/cargoes, total 4pcs During the inspection, taken total 4 pcs of samples were taken from steel coils by manufacturer under SGS inspector witness, the cutting was performed by manual cutting, position at the end of cargoes, after sampling, SGS inspector pasted the label marks on each piece of samples, and then the samples were sent to Tianjin SGS by manufacturer. Details as follow: sampling sampling SGS label on cargos Express No Inspection Order No.: IN-TJ Page No.: 4 of 8

5 sampling sampling SGS label on cargos Express No Result: The result was acceptable except remark. THIS REPORT ONLY REFLECTED OUR ACTUAL FINDINGS. THE INSPECTION WAS DONE TO THE BEST OF OUR KNOWLEDGE AND ABILITY AND WITH DUE CARE. THE FINDINGS ARE VALID AS FOR TIME AND PLACE OF INSPECTION. Attachment: Photos during inspection Inspection Order No.: IN-TJ Page No.: 5 of 8

6 Visual check Visual check Dimension check Inspection Order No.: IN-TJ Page No.: 6 of 8

7 Inspection Order No.: IN-TJ Page No.: 7 of 8

8 Quantity check End of report Quantity check Inspection Order No.: IN-TJ Page No.: 8 of 8