Lift Stik. Installation, Operation and Service Manual PLS PLS PLS PLS Model Number Serial # Date Placed in Service

Transcription

1 Lift Stik PLS PLS PLS PLS Installation, Operation and Service Manual Model Number Serial # Date Placed in Service IMPORTANT: READ CAREFULLY BEFORE INSTALLING OR OPERATING LIFT Part orders are subject to a $50 minimum charge. March 2017

2 This manual was current at the time of printing. To obtain the latest, most updated version, please contact the Customer Service Department or go to our website: -- you will find a complete list of current Owner s Manuals to print. PRESTO OWNER S MANUAL Page 2 LIFT STIK

3 C O N T E N T S S E C T I O N 1: Introduction...4 Responsibility of Owners and Users...5 S E C T I O N 2: Safety Alert Symbols and Signal Words...6 Safety...7 S E C T I O N 3: Installation...7 A. Inspection...7 S E C T I O N 4: Operation...7 A. Operating Instructions...7 B. Daily Operations Maintenance Checks...8 Operator Instructions...8 A. Preparation for Use...8 B. Operations...9 S E C T I O N 5: Battery Maintenance...9 A. Preparing to Charge a Battery...9 B. Locating the Charger...9 C. Precautions...9 D. Battery Charger Connection Precautions...10 S E C T I O N 6: Maintenance...13 A. Instructions...13 B. Monthly Operations Maintenance Checks...13 C. Maintenance...13 ORDERING REPLACEMENT PARTS...25 RESTOCKING POLICY...26 RETURN MAT'LS AUTHORIZATION (RMA) PROCEDURES...27 WARRANTY...28 L I S T O F F I G U R E S : Figure 1 Components Diagram...11 Figure 2 Specifications...12 Figure 3 Spare Parts...14 Figure 4 Chain Routing for PLS Figure 5 Changing the PLS Motor Figure 6 Wiring Diagrams...20 Figure 7 Lift Stik Dimensions PRESTO OWNER S MANUAL Page 3 LIFT STIK

4 S E C T I O N 1 INTRODUCTION This manual attempts to provide all of the information necessary for the safe and proper installation, operation and maintenance of Presto Lifts Inc. Lift Stik. It is important that all personnel involved with the installation, maintenance or operator of the stacker read this manual. Additional manuals are available upon request or at Each of the Presto Lift Inc. stackers is equipped with nameplate, serial number and model identifications. Please refer to these numbers when ordering parts or requesting further information. The Presto Lifts Inc. stackers are designed for lifting, lowering and positioning a wide variety of loads. WHERE UNIQUE SITUATIONS ARISE, WHICH ARE NOT COVRED IN THIS MANUAL, CALL PRESTO LIFTS FOR FURTHER INSTRUCTIONS. The battery-operated stackers are designed for in-plant/ non-hazardous locations only. These units are not for personnel lifting. All equipment is manually propelled and powered vertical travel. PRESTO OWNER S MANUAL Page 4 LIFT STIK

5 Responsibility of Owners and Users Inspection and Maintenance The device shall be inspected and maintained in proper working order in accordance with Presto s owner s manual. Removal from Service Any device not in safe operating condition such as, but not limited to, excessive leakage, missing rollers, pins, or fasteners, any bent or cracked structural members, cut or frayed electric, hydraulic, or pneumatic lines, damaged or malfunctioning controls or safety devices, etc. shall be removed from service until it is repaired to the original manufacturer s standards. Repairs All repairs shall be made by qualified personnel in conformance with Presto s instructions. Operators Only trained personnel and authorized personnel shall be permitted to operate PowerStak. Before Operation Before using the device, the operator shall have: Read and/or had explained, and understood, the manufacturer s operating instructions and safety rules. Inspected the device for proper operation and condition. Any suspect item shall be carefully examined and a determination made by a qualified person as to whether it constitutes a hazard. All items not in conformance with Presto s specification shall be corrected before further use of the PowerStak. During Operation The device shall only be used in accordance with this owner s manual. Do not overload. Ensure that all safety devices are operational and in place. Modifications or Alterations Modifications or alterations to any Presto industrial positioning equipment shall be made only with written permission from Presto. PRESTO OWNER S MANUAL Page 5 LIFT STIK

6 SAFETY ALERT SYMBOLS AND SIGNAL WORDS The safety of all persons operating, maintaining, repairing, or in the vicinity of this equipment is of paramount concern. This is a powerful machine with moving parts, and is capable of causing personal injury if proper precautions are not taken. Therefore, throughout this manual, certain hazards have been identified which may occur in the use of the machine, and there are appropriate instructions or precautions which should be taken to avoid these hazards. In some cases, there are consequences which may occur if instructions or precautions are not followed. Below are the symbols and signal words along with their definitions referenced from ANSI Z Product Safety Signs and Labels. Safety Alert Symbols These are the safety alert symbols.. They are used to alert you to potential physical injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. For use with DANGER signal word (Red Background) For use with WARNING signal word (Orange Background) For use with CAUTION signal word (Yellow Background) Signal Words The meaning of different signal words as defined by ANSI Standard Z535.4 indicates the relative seriousness of the hazardous situation. DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. (Red Background) WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. (Orange Background) (Yellow Background) CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE is used to address practices not related to personal injury. (Blue Background) SAFETY INSTRUCTIONS (Green Background) SAFETY INSTRUCTIONS (or equivalent) signs indicate safetyrelated instructions or procedures. PRESTO OWNER S MANUAL Page 6 LIFT STIK

7 S E C T I O N 2 SAFETY The battery-operated stackers are very powerful lifts capable of doing large amounts of work. DO NOT INSTALL OR OPERATE THESE LIFTS WITHOUT CAREFULLY READING THIS MANU- AL. In order to provide for the safe operation of these stackers, Presto Lifts Inc. has identified certain hazards that may occur during the installation, maintenance and use of these lifts. For safety reasons these units are designed to be serviced or repaired in the collapsed position. If performed properly, this will greatly reduce the possibility of injury. WARNING! Do not perform any repair work on lifts if there is a load on the forks or platform. Do not perform any repair work if the forks or platform is in the raised position. All personnel must stand clear of the lift while in motion. Do not put hands or feet under the forks or platform. Do not stand underneath the forks or platform. Do not stand in front of the stacker while in motion. Do not stand, sit or climb on the lift. Do not use the lift on soft, uneven or unstable surfaces. Do not exceed the load center or capacity. S E C T I O N 3 INSTALLATION A. INSPECTION: Upon receipt of the stacker, inspect the equipment completely to determine if there is any shipping damage, and that the lift is complete. Presto Lifts Inc. tests and inspects every piece of equipment prior to shipment. If damage is apparent, a freight claim must be filed with the freight company. Do not use the lift if there appears to be any damage. With the lift in a collapsed position, check the following: 1 Check for signs of damage especially to the back cabinet that houses the battery and power pack. 2 Check base frame for dimensions and structural integrity. 3 Inspect for any bent or damaged metal parts. S E C T I O N 4 OPERATION A. OPERATING INSTRUCTIONS: 1. To raise lift, push "Lift" button. 2. To lower lift, push "Lower" button. 3. Whenever the control handle is released, the lift stops. AUTHORIZED OPERATORS SHOULD READ AND UNDERSTAND ALL INSTRUCTIONS, PRE- CAUTIONS AND WARNINGS. IMPROPER USE OF THIS LIFT COULD RESULT IN INJURY AND/OR DAMAGE TO LOAD AND EQUIPMENT. 1 Inspect the lift for damaged or worn parts. Do not use if not in safe operating condition. 2 Use lift on hard level surfaces only. 3 Make sure load is evenly distributed, not loose or unstable, and is as far back on platform or forks as possible. Do not pick up loads on tips or forks or edge of platform. 4 For fork models, adjust forks to the maximum practical width. Pick up loads on both forks (not one). 5 Do not overload. Check load center and load weight capacities on manufacturer s nameplate. 6 Make sure travel and work area is clear of obstructions. 7 Check overhead clearance before lifting loads or transporting. 8 Make sure floor lock pad is in firm contact with floor before lifting load, lowering load or using as a workstation. 9 Brace or block lift when sliding loads on or off platform or forks. PRESTO OWNER S MANUAL Page 7 LIFT STIK

8 B. DAILY OPERATIONS MAINTENANCE CHECKS: 1. Battery A. Check for corroded and loose terminals. A white powder substance will be present if there is any existing corrosion. B. Visually inspect for any cracks or damage to the casing. C. Check for loose battery tie-downs. 2. Charger A. Inspect wire connections. B. Check power cord for nicks/damage. C. Check charger for proper mounting. 3. Frame Assembly A. Check wheel lock. B. Check chain roller assembly connections. C. Check for any worn or damaged parts. OPERATOR INSTRUCTIONS WARNINGS DO NOT use this lift until you have been trained and authorized to do so. DO NOT operate until you have read all warnings and instructions. DO NOT exceed load center or load weight capacities DO NOT operate until you have checked the conditions of the truck: lift systems, forks, chains, cables and floor lock. DO NOT use if any part is damaged, worn or not working properly. DO NOT use on ramps or inclines. Only smooth level surfaces. DO NOT use for lifting or carrying people. DO NOT handle unbalanced, unstable or loosely stacked loads. DO NOT travel with forks or platform in an elevated position. DO NOT handle high-unsecured loads that could fall backwards. DO NOT allow people to stand or pass under forks or platform with or without load. DO NOT operate when parts of anyone s body may be close to mast structure or any moving parts. DO NOT drop loads on platform or forks. DO NOT alter or modify this lift in any way. A. PREPARATION FOR USE This lift left our factory in perfect condition. It has been inspected and tested to assure performance standards PRESTO OWNER S MANUAL Page 8 LIFT STIK

9 have been met. Visually inspect lift for damage. Check for attachments and accessories that may have been ordered. If there is any damage or missing parts, report it to your carrier and your Presto Lifts dealer immediately. Remove all metal/plastic bands, cardboard and other material used for shipping purposes. Check to see if chains are in place, the wheel lock is in working order, and that the lift system is in working order. Connect battery cable. Check cables and wires on battery charger as well as battery. B. OPERATIONS PRECAUTIONS: AUTHORIZED OPERATORS SHOULD READ AND UNDERSTAND ALL INSTRUCTIONS, PRECAUTIONS AND WARNINGS. IMPROPER USE OF THIS LIFT TRUCK COULD RESULT IN INJURY AND/ OR DAMAGE TO LOAD AND EQUIPMENT. Inspect the lift for damaged or worn parts. Do not use if not in safe operating condition. Use lift on hard level surfaces only. Make sure load is evenly distributed (not loose or unstable), and is as far back on forks as possible. Do not pick up loads on tips of forks or edge of platform. Adjust forks to the maximum practical width. Pick up loads on both forks (not one). Do not overload: Check load center and load weight capacities on manufacturers name plate. Brace or block lift when sliding loads on or off platform or forks. S E C T I O N 5 BATTERY MAINTENANCE A. PREPARING TO CHARGE A BATTERY 1. Be sure area around lift and the battery is well ventilated while battery is being charged. 2. The battery terminals, connections and wiring including the plug in the battery box and charger connections should be clean and free of corrosion. When cleaning any of these components wear a face shield or other suitable protective eyewear. 3. For a sealed battery (a battery without cell caps) carefully follow the manufacturer s recharging instructions that are provided with the battery. If you do not have a copy of these instructions or the instructions for the battery charger they are available free of charge by calling Presto Read, understand and follow all battery and battery charger manufacturer s specific precautions while working with and/or charging batteries. B. LOCATING THE CHARGER 1. Locate charger as far away from battery as the cables permit. 2. Do not operate charger in a closed area or restrict ventilation in any way. Make sure travel and work area is clear of obstructions. Check overhead clearance before lifting loads or transporting. Make sure floor lock or pad is secured to floor before lifting, lowering or using as a workstation. C. PRECAUTIONS FOR GROUNDING AND AC POWER CORD CONNECTION Charger should be grounded to reduce risk of electric shock. Charger is equipped with an electric cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. PRESTO OWNER S MANUAL Page 9 LIFT STIK

10 DANGER Never alter the AC cord or plug provided. If it will not fit outlet, have proper outlet installed by a qualified electrician. Improper connection can result in a risk of an electric shock. D. BATTERY CHARGER CONNECTION PRECAUTIONS CAUTION Connect and disconnect the DC output plug (or clips) only when the AC cord is disconnected from the electric outlet. Never allow clips to touch each other. 1. When hooking up the charger, attach the plug into the twist-lock receptacle on the side of the battery box or connect the clips directly to the battery on units that are not pre-wired with a plug on the side of the battery box. 3. The POSITIVE (red or white) clip from the battery charger to the POSITIVE (POS, P, +) post of the battery. 4. When making each connection, twist or rock clip back and forth several times to make a good connection and to reduce the risk of a clip slipping off and creating a spark. Do not twist or rock clip on the battery after the second clip connection is made. 5. When disconnecting the charger, disconnect AC cord from the electrical outlet before removing any clips from battery or chassis. IF THESE INSTRUCTIONS ARE NOT CLEAR OR IF THERE ARE ANY QUESTIONS PLEASE CON- TACT PRESTO LIFTS INC. FOR UNITS NOT EQUIPPED WITH A TWIST- LOCK, PREWIRED CHARGER PLUG FOLLOW THESE ADDITIONAL PRECAUTIONS 1. Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has larger diameter than NEGA- TIVE (NEG, N, -) battery post. 2. Determine which post of battery is grounded (connected) to the chassis of the machine. Connect the NEGATIVE (Black) clip from the battery charger to the machine chassis as far away from the battery as possible. PRESTO OWNER S MANUAL Page 10 LIFT STIK

11 Figure 1: Components Diagram ITEM DESCRIPTION 1 Motor 2 Battery 3 Circuit board 5 Control unit 6 Caster with brake 7 Caster, fixed wheel 8 Caster, fixed wheel 11 Main switch 12 Battery charger PRESTO OWNER S MANUAL Page 11 LIFT STIK

12 Figure 2: Specifications The maximum load refers to the load being uniformly distributed over the entire platform on the basic performance of each work positioner model. If the accessory is added by the purchaser, a new weight decal might be required on the work positioner. G = Center of gravity H = Maximum platform height Q = Maximum permitted load (capacity) D = Maximum center of gravity. Distance from the mast in relation to the platform/attachment area. D may not exceed half the platform length Please contact Presto Lifts Inc. to discuss specific load if it does not meet standard criteria. PRESTO OWNER S MANUAL Page 12 LIFT STIK

13 S E C T I O N 6 MAINTENANCE Operation of Presto Lift Stik is very simple as is their construction. They require very little maintenance. Reasonable care will result in excellent trouble-free performance. Presto Lift Stik's are designed for oneperson operation and ease of performance. A. INSTRUCTIONS: 1 Grease wheels and casters at least once a month to maintain easy roll of lift. 2 Do not overload your lift. 3. Lubricate monthly with PTFE Dry Workshop Lube or equivalent. B. MONTHLY OPERATIONS MAINTENANCE CHECKS: 1. Battery (maintenance free) A. Clean terminals. 2. Frame Assembly A. Clean and lubricate all roller bearings and cam followers. B. Clean and inspect all welds. C. Check wheels for wear and damage. D. Inspect nameplate for legibility. Place the serial and model number shown on the nameplate on the cover of the manual for future reference. Operator Daily Checks DAMAGE: Check for bent, dented, worn or broken parts. WHEELS AND CASTERS: Check for wear and that they are turning smoothly. LIFT CHAINS: Check to see that they are in place and not loose. FORKS: Check that they are in place and stable. LIFT SYSTEM: Check to assure that there is no binding or excessive play in the platform or fork back plate. WHEEL LOCK: Check to assure pad is contacting the wheel and holds truck in place. CABLES; WIRES: Check that there are no loose cables or wires. CAUTION: DO NOT USE LIFT IF IT IS NOT PERATING PROPERLY, OR APPEARS UNSAFE IN ANY WAY! C. MAINTENANCE The attached bulletin outlines maintenance instructions and parts. A visual check should be made on a daily basis to assure the safety of the lift. PRESTO OWNER S MANUAL Page 13 LIFT STIK

14 Figure 3: SPARE PARTS PLS PLS PLS PLS Motor Contact Parts Department 2 Battery * * * * 3 Circuit board Contact Parts Department 4 Charger cable R R R R Control unit w/ cable R86005 R86005 R86005 R Front Wheel R84251 R86003 R86003 R Rear Swivel Wheel R84250 R84297 R84297 R Lift Chain R86009 R86011 R86012 R Transmission Chain R Sprocket wheel kit R86019 R86020 R86020 R Main switch R86004 R86004 R86004 R Battery charger R84242** R84242** R84242** R84242** 13 Front Shroud Rear Shroud Up/Down Limit Switch * The repair parts battery will be different than the original, but it will functionally do the same job. ** For machines manufactured in October 2005 or newer. Note: (Lift Stiks require 2 batteries each) PRESTO OWNER S MANUAL Page 14 LIFT STIK

15 Figure 4: CHAIN ROUTING PLS PRESTO OWNER S MANUAL Page 15 LIFT STIK

16 Changing the PLS Motor PRESTO OWNER S MANUAL Page 16 LIFT STIK

17 Figure 5: Changing the PLS Motor (Pages 14-16) PRESTO OWNER S MANUAL Page 17 LIFT STIK

18 PRESTO OWNER S MANUAL Page 18 LIFT STIK

19 PRESTO OWNER S MANUAL Page 19 LIFT STIK

20 Figure 6: Wiring Diagrams Electrical Diagram PLS52-185, PLS48-230, PLS Electrical Diagram PLS PRESTO OWNER S MANUAL Page 20 LIFT STIK

21 Figure 7: Lift Stik Dimensions (Pages18-21) PRESTO LIFT STIK PLS MODEL LIFTING RAISED LOWERED LENGTH WIDTH HEIGHT PLATFORM SIZE BATTERY CHARGER WEIGHT INCL. NUMBER CAPACITY HEIGHT HEIGHT (inches) (inches) (inches) (w x l) (lbs.) (lbs.) (inches) (inches) PLS / /2 x 23-1/2 24V/7,2Ah 1,5A 115V 86 PRESTO OWNER S MANUAL Page 21 LIFT STIK

22 PRESTO LIFT STIK PLS MODEL LIFTING MAXIMUM MINIMUM LENGTH WIDTH HEIGHT PLATFORM SIZE BATTERY CHARGER WEIGHT INCL. NUMBER CAPACITY HEIGHT HEIGHT (inches) (inches) (inches) (w x l) EMB (lbs.) (lbs.) (inches) (inches) PLS /4 33-1/4 23-3/ X VDC 115V 93 PRESTO OWNER S MANUAL Page 22 LIFT STIK

23 PRESTO LIFT STIK PLS MODEL LIFTING MAXIMUM MINIMUM LENGTH WIDTH HEIGHT PLATFORM SIZE BATTERY CHARGER WEIGHT INCL. NUMBER CAPACITY HEIGHT HEIGHT (inches) (inches) (inches) (w x l) EMB (lbs.) (lbs.) (inches) (inches) PLS /4 33-1/4 23-3/4 75-1/2 18 X VDC 115V 99 PRESTO OWNER S MANUAL Page 23 LIFT STIK

24 PRESTO LIFT STIK PLS MODEL LIFTING MAXIMUM MINIMUM LENGTH WIDTH HEIGHT PLATFORM SIZE BATTERY CHARGER WEIGHT INCL. NUMBER CAPACITY HEIGHT HEIGHT (inches) (inches) (inches) (w x l) EMB (lbs.) (lbs.) (inches) (inches) PLS / /2 22 X 23 24V / 12ah 1.5A/115V 141 PRESTO OWNER S MANUAL Page 24 LIFT STIK

25 Ordering Replacement Parts Presto Lifts has carefully chosen the components in your unit to be the best available for the purpose. Replacement parts should be identical to the original equipment. Presto Lifts will not be responsible for equipment failures resulting from the use of incorrect replacement parts or from unauthorized modifications to the unit. Presto Lifts can supply all replacement parts for your lift. With your order, please include the model number and the serial number of the unit. You can find these numbers on the name plate. This plate is located within the cabinet, or the angle iron cylinder cross support. To order replacement parts, please call the Presto Parts Department. Parts are shipped subject to the following terms: FOB factory Returns only with the approval of our parts department. Credit cards preferred (except parts covered by warranty). Freight collect for truck (except parts covered by warranty). Freight - prepaid and invoice for small parcel shipments (except parts covered by warranty). The warranty for repair parts is 30 days from date of shipment. Parts replaced under warranty are on a charge-credit basis. We will invoice you when we ship the replacement part, then credit you when you return the worn or damaged part, and we verify that it is covered by our warranty. Labor is not covered under warranty for Parts orders. Presto Lifts Parts Department 50 Commerce Way Norton, MA Telephone: FAX: Service@PrestoLifts.com PRESTO OWNER S MANUAL Page 25 LIFT STIK

26 PARTS Standard parts may be returned with a 20% restocking fee. Modified or custom-engineered parts are not returnable. Unfortunately, due to potentially concealed damage, all sales of electrical assemblies are final. QUALITY ISSUES Should you feel there is a quality problem, please contact the seller to ask questions and gather information on how to rectify the issue. Presto Lift Inc. reserves the right to determine potential credits, as a result of factory defects, based on its inspection of the merchandise. GENERAL All products shipped from our factory have passed Quality Assurance inspection and testing. The carrier of choice has signed for, and accepted the product in new working condition. The customer should inspect to ensure it is not received damaged, has no concealed damage or is not incomplete. Parts orders are determined to be complete based upon Presto Lift, Inc. inspection sheets and carrier shipping weights. PRESTO OWNER S MANUAL Page 26 LIFT STIK

27 RETURN GOODS AUTHORIZATION POLICY Presto Lifts provides the Return Goods Authorization (RGA) Policy, for specific models, as a courtesy to our distributors in the event they do not receive what they ordered. If a customer wishes to return a Presto Lifts product, please contact the Customer Service Department and request an RGA number. This request must be made on or before the fifteenth calendar day following the date of Presto Lifts invoice for the merchandise. Not all units are returnable. Quantity orders and special designs cannot be returned under any circumstances. Presto Customer Service reserves the right for final judgment on all product returns. The RGA number must appear on the outside of any packaging material for a return to be accepted and processed by Presto Lifts. Customers shipping returns from the Continental US, Canada, or Mexico have thirty (30) days from date of RGA issue to have the product arrive at Presto Lifts facility. All merchandise must arrive Free on Board at Presto Lifts facility or the shipment will be refused and returned to the sender. All credits are issued less restocking and refurbishing charges, regardless if the merchandise was damaged in transit. Return addresses: please refer to your RMA for the address to which your product should be returned. Presto Lift Inc. 715 Highway 77 Manila, Arkansas Telephone: Fax: PRESTO OWNER S MANUAL Page 27 LIFT STIK

28 Presto Lifts Limited Warranty Policy Presto Lifts warrants all of its products against defects in the welded structural frame and, if applicable, scissor legs from faulty material and workmanship for a period of five (5) years from the date of invoice. All batteries and battery chargers have a limited warranty against defects in faulty material and workmanship for a ninety (90) day period from the date of invoice through Presto Lifts. All other components have a limited warranty against defects in faulty material and workmanship for a two (2) year period from the date of invoice and a 30 day limited warranty on labor. Please note that prior authorization from Presto Lifts is required on all warranty work. There are no implied warranties of any kind, more specifically, there are no warranties of merchantability or fitness for any particular purpose. Presto Lifts' sole warranty shall be as set forth in this limited warranty. Presto Lifts will elect to repair or replace a defective component without charge, if any components should become defective within the limited warranty period. Proof of purchase is required for warranty. The charge for shipping the defective component is the responsibility of the buyer and must be accompanied with an RMA number. The shipping charge to return the component to the buyer is the responsibility of Presto Lifts, Inc. This limited warranty does not cover labor expense for removal or reinstallation of components after thirty days. This limited warranty shall not cover, among other things: damages resulting from foreign matter or water, failure to provide reasonable and necessary maintenance, and if applicable, use of product while charger is plugged into an AC outlet, or failure to follow operating instructions. The limited warranty is not valid for damage resulting from negligence, accident, unreasonable use, abuse or misuse, exceeding data plate capacities or altering the product without Presto Lifts authorization. Presto Lifts expressly disclaims and excludes any liability for consequential, incidental, indirect or punitive damages or financial loss to people or property resulting from any breach of warranty or the operation or failure of this product. Presto Lifts makes no representation that this product complies with local, state, or federal safety/product standards codes. Should this product fail to comply in any way with those codes, it shall not be considered a defect of materials or workmanship. Presto Lifts shall not be held liable for any damages resulting from noncompliance. It is the dealer's responsibility to exercise this limited warranty. This limited warranty is provided to the original purchaser (defined as the original end user) and is nontransferable. This constitutes the complete and final agreement involving Presto Lifts and limited warranty obligations for products. PRESTO OWNER S MANUAL Page 28 LIFT STIK